Програмируем температурен контролер - терморегулатор. 2-level Display: PV and SV. Control Output 2 None Voltage output (for driving SSR)

Transcription

1 Програмируем температурен контролер - терморегулатор (48 x 48 mm) CSM DS_E Programmable Controllers Join the Series! Program up to 256 segments and take advantage of the high cost performance of the new CD that improves both the field of view and contrast. Set up to 8 programmed patterns with up to 32 segments (steps) each. igh-resolution display with 5 digits/. C display in a compact Controller (48 x 48 mm). igh-speed sampling cycle of 6 ms. igh Accuracy Thermocouple/Pt input: ±.% of PV Analog input: ±.% FS Universal inputs on all models (thermocouple, PT, or analog input) to handle various sensors with one Controller. A PV/SV-status display function can be set to automatically alternate between displaying the status of the Temperature Controller (auto/ manual, RUN/RESET, and alarms) and the PV or SV. Flexible contact outputs with logic operations (AND, OR, and delays) set from the Support Software (C-Thermo version 4.3). Program settings can be managed. Preventive maintenance for relays in the Temperature Controller using a Control Output / Counter mm Refer to Safety Precautions for E5@N/E5@N-/ E5@N-T. Refer to Operation for E5@N/E5@N-/ E5@N-T for operating procedures. Main I/O Functions Event Inputs None Two 2-level Display: PV and SV 5-digit Display with high resolution of. C Universal Sensor Inputs Universal thermocouple/pt/analog (current/voltage) inputs. Indication Accuracy Thermocouple/Pt input: ±.% of PV Analog input: ±.% FS Sampling Period 6 ms Control Output 2 None Voltage output (for driving SSR) Auxiliary Outputs Two Control Output Relay output Voltage output (for driving SSR) Current output inear voltage output Programmable function 8 programs 32 segments Auto/manual switching Temperature Controller status display Simple program function ogic operations Control output / count alarm PV change rate alarm s also available with or RS-232C communications This data sheet is provided as a guideline for selecting products. Be sure to refer to the following user manuals for application precautions and other information required for operation before attempting to use the product. /E5AN-T/E5EN-T Digital Controllers User's Manual Programmable Type (Cat. No. 69) /E5AN-T/E5EN-T Digital Controllers Manual Programmable Type (Cat. No. 7)

2 ineup Programmable Type Terminal block Fully universal input control output 2 auxiliary outputs 2 control outputs 2 auxiliary outputs Note: s with one control output and models with two control outputs can be used for heating/cooling control. Number Structure Number egend Controllers E5CN-@@@M@-@ Type T: Programmable 2. Control Output R: Relay output Q: Voltage output (for driving SSR) C: Current output V: inear voltage output 3. Auxiliary Outputs 2: Two outputs 4. Option M: Option Unit can be mounted. 5. Power Supply Voltage Blank: to 24 VAC D: 24 VAC/VDC 6. Case Color Blank: Black 7. Terminal Cover -5: With terminal cover Option Units E53-@@@@ Applicable Controller CN:, E5CN- or E5CN 2. Function Blank: None Q: (voltage output for driving SSR) P: Power supply for sensor C: Current output 3. Function 2 Blank: None : eater burnout/ssr failure/eater overcurrent detection (CT) : eater burnout/ssr failure/eater overcurrent detection (CT2) B: Two event inputs 3: communications 3: eater burnout/ssr failure/eater overcurrent detection (CT) + communications B: eater burnout/ssr failure/eater overcurrent detection (CT) + Two event inputs 3: eater burnout/ssr failure/eater overcurrent detection (CT2) + communications : eater burnout/ssr failure/eater overcurrent detection (CT)/RS-232C communications F: Transfer output BF: Two event inputs/transfer output 4. Version N2: Available only to models released after January 28 Note:. Not all combinations of function and function 2 specifications are possible for Option Units (E53-@@@@). 2. Estimates can be provided for coatings and other specifications that are not given in the datasheet. Ask your OMR representative for details. 2

3 Ordering Information Controllers /6 DIN (W D) Size Case Color Power supply voltage Auxiliary output Control output Black Option Units One of the following Option Units can be mounted to provide the E5CN with additional functions. RS-232C RS-232C RS-232C Note: These Option Units are applicable only to models released after January 28. Accessories (Order Separately) USB-Serial Conversion Cable to 24 VAC 2 24 VAC/VDC 2 Functions 3-phase heater burnout/ssr failure/ eater overcurrent detection eater burnout/ssr failure/ eater overcurrent detection eater burnout/ssr failure/ eater overcurrent detection Event inputs Event inputs eater burnout/ssr failure/ eater overcurrent detection 3-phase heater burnout/ssr failure/ eater overcurrent detection Event inputs eater burnout/ssr failure/ eater overcurrent detection Adapter Relay output Voltage output (for driving SSR) Current output inear voltage output Relay output Voltage output (for driving SSR) Current output inear voltage output (Voltage for driving SSR) (Voltage for driving SSR) (Voltage for driving SSR) (Voltage for driving SSR) (Voltage for driving SSR) Transfer Output R2M-5 Q2M-5 C2M-5 V2M-5 R2MD-5 Q2MD-5 C2MD-5 V2MD-5 E53-CN3N2 E53-CNBN2 E53-CNQ3N2 E53-CN3N2 E53-CN3N2 E53-CNBN2 E53-CNQN2 E53-CNQN2 E53-CNQBN2 E53-CNQFN2 Event inputs Transfer Output E53-CNBFN2 (Voltage for driving SSR) E53-CNQN2 E53-CNN2 E53-CNN2 Terminal Cover E53-COV7 Note:. The Terminal Cover comes with the E5CN-@@@-5 models. 2. The E53-COV cannot be used. Waterproof Packing E58-CIFQ Y92S-29 Note: Waterproof Packing is included with the controller only for models with terminal blocks. Connectable models Terminal type Y92F-45 Note: Use this Adapter when the panel has been previously prepared for the E5B@. Front cover Type ard Front Cover Soft Front Cover C-Thermo Support Software EST2-2C-MV4 Y92A-48B Y92A-48D Current Transformers (CTs) ole diameter 5.8 dia. E54-CT. dia. E54-CT3 3

4 Specifications Ratings Power supply voltage Operating voltage range Power consumption Sensor input Input impedance Control method Control output Auxiliary output Event input ogic operations Transfer outputs R input Relay output Voltage output (for driving SSR) No D in model number: to 24 VAC, 5/6 z D in model number: 24 VAC, 5/6 z; 24 VDC 85% to % of rated supply voltage to 24 VAC: 8.5 VA (max.) (R2 at VAC: 3. VA) 24 VAC/VDC: 5.5 VA (24 VAC)/3.5 W (24 VDC) (max.) (R2D at 24 VAC: 2.7 VA) Any of the following can be selected (i.e., fully universal input). Thermocouple: K, J, T, E,, U, N, R, S, B, W, or P II Platinum resistance thermometer: Pt or JPt Current input: 4 to 2 ma or to 2 ma Voltage input: to 5 V, to 5 V, or to V Storage temperature 25 to 65 C (with no condensation or icing) * For models with current outputs, control output can be used as a transfer output. Current input: Ω max., Voltage input: MΩ min. (Use a : connection when connecting the ES2-B.) / control or 2-PID control (with auto-tuning) ST-NO, 25 VAC, 3 A (resistive load), electrical life:, operations, minimum applicable load: 5 V, ma Output voltage: VDC ±% (PNP), max. load current: 2 ma, with short-circuit protection circuit Current output 4 to 2 ma DC/ to 2 ma DC, load: 6 Ω max., resolution: approx., * inear voltage output Number of outputs Output specifications Number of outputs 2 External contact input specifications Number of operations Operations Outputs Setting method Work bit assignments Number of outputs Output specifications Indication method Other functions Ambient operating temperature to VDC (load: kω min.), Resolution: Approx., 2 max. Relay output: ST-NO, 25 VAC, 3 A (resistive load), electrical life:, operations, minimum applicable load: 5 V, ma Contact input: : kω max., : kω min. Non-contact input: : Residual voltage:.5 V max., : eakage current:. ma max. Current flow: Approx. 7 ma per contact 8 max. (Combinations can be made using work bits.) ogic operation: Any of the following four patterns can be selected. The input status may be inverted. (A and B) or (C and D), (A or C) and (B or D), A or B or C or D, A and B and C and D (A, B, C, and D are four inputs.) Delay: delay or delay for the results of the logic operation given above. Setting time: to 9999 s or to 9999 min Output inversion: Possible One work bit per operation Any of the following can be assigned to up to eight work bits (logic operation results): Operation commands (assigned to event inputs) *, auxiliary outputs, or control outputs. * Application is possible with models that do not have event inputs by using an internal assignment. max. Current output: 4 to 2 ma DC, oad: 6 Ω max., Resolution at 4 to 2 ma: Approx., Not supported Ambient operating humidity 25% to 85% Digital setting using front panel keys -segment digital display and individual indicators (7-segments displays also possible) Character height: PV: mm, SV: 6.5 mm Manual output, heating/cooling control, loop burnout alarm, other alarm functions, heater burnout detection (including SSR failure and heater overcurrent detection), 4% AT, % AT, MV limiter, input digital filter, temperature input shift, run/reset, protection functions, control output / counter, extraction of square root, MV change rate limit, PV/SV status display, automatic cooling coefficient adjustment, program control functions, etc. to 55 C (with no condensation or icing), for 3-year warranty: to 5 C 4

5 Input Ranges Thermocouple/Platinum Resistance Thermometer/Analog Input (Fully Universal Inputs) Temperature range ( C) Input type Platinum resistance thermometer Thermocouple Name Pt JPt K J T E U N R S B W P II Setting number Analog input 4 to to 2 ma 2 ma 5V Usable in the following ranges by scaling: to 324, to 324., to 324., or to Shaded settings are the default settings. The applicable standards for the input types are as follows: K, J, T, E, N, R, S, B: JIS C , IEC 584- : Fe-CuNi, DIN U: Cu-CuNi, DIN W: W5Re/W26Re, ASTM E JPt: JIS C , JIS C Pt: JIS C , IEC 75 P II: According to Platinel II electromotive force charts from BASF (previously Engelhard) to 5V to V 5

6 Alarm Outputs Each alarm can be independently set to one of the following alarm types. The default is 2: Upper limit. Auxiliary outputs are allocated for alarms. delays and delays ( to 999 s) can also be specified. Note: For models with heater burnout, SSR failure, and heater overcurrent detection, alarm will be an OR output of the alarm selected from the following alarm types and the alarms for heater burnout, SSR failure, and heater overcurrent. To output only a heater burnout alarm, SSR failure alarm, and heater overcurrent alarm for alarm, set the alarm type to (i.e., no alarm function). Set value Alarm type *. With set values, 4 and 5, the upper and lower limit values can be set independently for each alarm type, and are expressed as and. *2. Set value:, Upper- and lower-limit alarm *3. Set value: 4, Upper- and lower-limit range >, < *4. Set value: 5, Upper- and lower-limit with standby sequence For Upper- and ower-imit Alarm Described Above Case and 2 Always when the upper-limit and lower-limit hysteresis overlaps. Case 3: Always Alarm output operation When alarm value is positive When alarm value is negative Alarm function Output No alarm * Upper- and lower-limit *2 2 Upper-limit 3 ower-limit 4 * Upper- and lower-limit range *3 5 * Upper- and lower-limit with standby sequence 6 Upper-limit with standby sequence 7 ower-limit with standby sequence 8 Absolute-value upper-limit 9 Absolute-value lower-limit Absolute-value upper-limit with standby sequence Absolute-value lower-limit with standby sequence BA (alarm type only) --- *7 PV change rate alarm --- *8 Case <, > < Case <, > < Case 2 >, < > Case 2 >, < > *5 Case 3 (Always ) Case 3 (Always ) <, < <, > >, < <, < <, > *4 Description of function Set the deviation in the set point by setting the alarm upper limit () and alarm lower limit (). Set the upward deviation in the set point by setting the alarm value (). Set the downward deviation in the set point by setting the alarm value (). Set the deviation in the set point by setting the alarm upper limit () and alarm lower limit (). A standby sequence is added to the upper- and lower-limit alarm (). *6 A standby sequence is added to the upper-limit alarm (2). *6 A standby sequence is added to the lower-limit alarm (3). *6 The alarm will turn if the process value is larger than the alarm value () regardless of the set point. The alarm will turn if the process value is smaller than the alarm value () regardless of the set point. A standby sequence is added to the absolute-value upper-limit alarm (8). *6 A standby sequence is added to the absolute-value lower-limit alarm (9). *6 *5. Set value: 5, Upper- and lower-limit with standby sequence Always when the upper-limit and lower-limit hysteresis overlaps. *6. Refer to the /E5AN-T/E5EN-T Digital Controllers User's Manual (Cat. No. 69) for information on the operation of the standby sequence. *7. Refer to the /E5AN-T/E5EN-T Digital Controllers User's Manual (Cat. No. 69) for information on the loop burnout alarm (BA). *8. Refer to the /E5AN-T/E5EN-T Digital Controllers User's Manual (Cat. No. 69) for information on the PV change rate alarm. 6

7 Characteristics Indication accuracy Transfer output accuracy Influence of temperature *2 Influence of voltage *2 Input sampling period ysteresis Proportional band (P) Thermocouple: (±.% of indicated value or ± C, whichever is greater) ± digit max. * Platinum resistance thermometer: (±.% of indicated value or ±.5 C, whichever is greater) ± digit max. Analog input: ±.% FS ± digit max. CT input: ±5% FS ± digit max. ±.3% FS max. Thermocouple input (R, S, B, W, PII): (±% of PV or ± C, whichever is greater) ± digit max. Other thermocouple input: (±% of PV or ±4 C, whichever is greater) ± digit max. *3 Platinum resistance thermometer: (±% of PV or ±2 C, whichever is greater) ± digit max. Analog input: (±%FS) ± digit max. 6 ms Temperature input:. to 324. C or F (in units of. C or F) Analog input:.% to 99.99% FS (in units of.% FS) Temperature input:. to 324. C or F (in units of. C or F) Analog input:.% to 999.9% FS (in units of.% FS) Integral time (I). to 324. s (in units of. s) Derivative time (D). to 324. s (in units of. s) Control period.5, to 99 s (in units of s) Manual reset value. to.% (in units of.%) Alarm setting range Affect of signal source resistance Insulation resistance Dielectric strength Vibration resistance Shock resistance Weight Malfunction Destruction Malfunction Destruction Degree of protection Memory protection Setup Tool Setup Tool port Standards Approved standards Conformed standards 9999 to 324 (decimal point position depends on input type) Thermocouple:. C/Ω max. ( Ω max.) Platinum resistance thermometer:. C/Ω max. ( Ω max.) 2 MΩ min. (at 5 VDC) 2,3 VAC, 5 or 6 z for min (between terminals with different charge) to 55 z, 2 m/s 2 for min each in, Y, and Z directions to 55 z,.75-mm single amplitude for 2 hrs each in, Y, and Z directions m/s 2, 3 times each in, Y, and Z directions 3 m/s 2, 3 times each in, Y, and Z directions Controller: Approx. g, Mounting Bracket: Approx. g Front panel: IP66, Rear case: IP2, Terminals: IP Non-volatile memory (number of writes:,, times) C-Thermo version 4.3 or higher Provided on the bottom of the. Use this port to connect a computer to the. An E58-CIFQ USB-Serial Conversion Cable is required to connect the computer to the. *4 U 6-, CSA C22.2 No. - EN 6- (IEC 6-): Pollution level 2, overcurrent category II EMI: EN 626 Radiated Interference Electromagnetic Field Strength: EN 55 Group, class A Noise Terminal Voltage: EN 55 Group, class A EMS: EN 626 ESD Immunity: EN EMC Electromagnetic Field Immunity: EN Burst Noise Immunity: EN Conducted Disturbance Immunity: EN Surge Immunity: EN Power Frequency Magnetic Field Immunity: EN Voltage Dip/Interrupting Immunity: EN 6-4- *. The indication accuracy of K thermocouples in the 2 to C range, T and N thermocouples at a temperature of C max., and U and thermocouples at any temperatures is ±2 C ± digit max. The indication accuracy of the B thermocouple at a temperature of 4 C max. is not specified. The indication accuracy of B thermocouples in the 4 to 8 C range is ±3 C max. The indication accuracy of the R and S thermocouples at a temperature of 2 C max. is ±3 C ± digit max. The indication accuracy of W thermocouples is ±.3 of PV or ±3 C, whichever is greater, ± digit max. The indication accuracy of P II thermocouples is ±.3 of PV or ±2 C, whichever is greater, ± digit max. *2. Ambient temperature: C to 23 C to 55 C, Voltage range: % to % of rated voltage *3. K thermocouple at C max.: ± C max. *4. External communications (RS-232C or ) and cable communications for the Setup Tool can be used at the same time. 7

8 Program Control Number of programs (patterns) 8 Number of segments (steps) 32 Segment setting method Segment times Alarm setting Reset operation Startup operation PID sets Alarm function Program status control Wait operation Time signals Program status output Program startup operation Operation end operation Program shift Time setting (Segment set with set point and time.) Gradient setting (Segment type with set point, gradient, and time.) h min to 99 h 59 min min s to 99 min 59 s Set separately for each program. Select either stopping control or fixed operation. Select continuing, resetting, manual operation, or run mode. Number of sets 8 Setting method Set separately for each program (automatic PID group selection also supported). Select from ramp and target. Segment operation Program operation Wait method Wait width setting Advance, hold Program repetitions and program links Waiting at segment ends Same wait width setting for all programs Number of outputs 2 Number of / Operations each per output Setting method Set separately for each program. Program end output (pulse width can be set), run output, stage output PV start Standby Select from segment set point, slope-priority PV start h min to 99 h 59 min day h to 99 day 23h Select from resetting, continuing control at final set point, and fixed control. Same program shift for all programs 8

9 USB-Serial Conversion Cable Applicable OS Windows 2, P, Vista, or 7 Applicable software Applicable models C-Thermo version 4 or higher E5AN/E5EN/E5CN/E5CN-U/ E5AN-/E5EN-/E5CN-/E5AN- T/E5EN-T//E5GN USB interface standard Conforms to USB Specification.. DTE speed Connector specifications Power supply Power supply voltage Current consumption Ambient operating temperature 384 bps Computer: USB (type A plug) Temperature Controller: Setup Tool port (on bottom of Controller) Bus power (Supplied from USB host controller.) 5 VDC 7 ma Ambient operating humidity % to 8% Storage temperature Storage humidity % to 8% Altitude to 55 C (with no condensation or icing) 2 to 6 C (with no condensation or icing) Weight Approx. g Note: A driver must be installed in the personal computer. Refer to installation information in the operation manual for the Conversion Cable. Specifications Transmission line connection method Synchronization method Protocol Baud rate Transmission code Data bit length * Stop bit length * Error detection Flow control Interface Retry function buffer response wait time 2, m max. : Multipoint RS-232C: Point-to-point (two-wire, half duplex)/rs-232c Start-stop synchronization CompoWay/F or Modbus, 24, 48, 96, 92, 384, or 576 bps ASCII (CompoWay/F, SYSWAY) RTU (Modbus) 7 or 8 bits or 2 bits Vertical parity (none, even, odd) Block check character (BCC) with CompoWay/F or CRC-6 Modbus None, RS-232C None 27 bytes to 99 ms Default: 2 ms * The baud rate, data bit length, stop bit length, and vertical parity can be individually set using the Setting evel. Current Transformer (Order Separately) Ratings Dielectric strength, VAC for min Vibration resistance 5 z, 98 m/s 2 Weight Accessories (E54-CT3 only) E54-CT: Approx..5 g, E54-CT3: Approx. 5 g Armatures (2) Plugs (2) eater Burnout Alarms, SSR Failure Alarms, and eater Overcurrent Alarms CT input (for heater current detection) Maximum heater current Input current indication accuracy eater burnout alarm setting range * SSR failure alarm setting range *2 eater overcurrent alarm setting range *3 s with detection for singlephase heaters: One input s with detection for singlephase or three-phase heaters: Two inputs 5 A AC ±5% FS ± digit max.. to 49.9 A (in units of. A) Minimum detection time: ms. to 49.9 A (in units of. A) Minimum detection time: ms. to 49.9 A (in units of. A) Minimum detection time: ms *. For heater burnout alarms, the heater current will be measured when the control output is, and the output assigned to the alarm function will turn if the heater current is lower than the set value (i.e., heater burnout detection current value). *2. For SSR failure alarms, the heater current will be measured when the control output is, and the output assigned to the alarm function will turn if the heater current is higher than the set value (i.e., SSR failure detection current value). *3. For heater overcurrent alarms, the heater current will be measured when the control output is, and the output assigned to the alarm function will turn if the heater current is higher than the set value (i.e., heater overcurrent detection current value). Electrical ife Expectancy Curve for Relays (Reference Values) No. of operations ( 4 ) VAC, 3 VDC (resistive load) cosφ = Switching current (A) 9

10 External Connections A voltage output (control output, for driving SSR) is not electrically insulated from the internal circuits. When using a grounding thermocouple, do not connect any of the control output terminals to ground. If the control output terminals are connected to ground, errors will occur in the measured temperature values as a result of leakage current. Controllers Control output Relay output 25 VAC, 3 A (resistive load) Voltage output (for driving SSR) VDC, 2 ma inear voltage output to VAC oad kω min. Current output to 2 ma DC 4 to 2 ma DC oad 6 Ω max. ma The Temperature Controller is set for a K-type thermocouple (input type = 5) by default. An input error (s.err) will occur if the input type setting does not agree with the temperature sensor. Check the input type. V Control output A B B Auxiliary outputs (relay outputs) Auxiliary output 2 Auxiliary output? Input power supply Auxiliary outputs (relay outputs) 25 VAC, 3 A (resistive load) A heater burnout alarm, SSR failure, heater overcurrent alarm, or input alarm is sent to the output to which the alarm function is assigned. to 24 VAC 24 VAC/VDC (no polarity) Option Units E53-CNBN2 Event Inputs E53-CNQBN2 E53-CNBN2 E53-CNBFN2 Event Inputs and Control Output 2 Event Inputs and CT Event Inputs and Transfer Output EV EV2 EV2 EV VDC 2 ma EV2 CT EV EV2 EV Transfer output 4 to 2 ma DC (oad 6 Ω max.) CT2 E53-CNQN2 Control Output 2 and CT2 VDC 2 ma CT E53-CNQFN2 E53-CNN2 E53-CNN2 E53-CNQN2 Control Output 2 and (RS-232) Transfer Output (RS-232) (RS-232) and CT and Control Output 2 RS-232C RS-232C RS-232C SD SD SD VDC 2 ma RD RD RD SG SG SG 4 to 2 ma DC Transfer output CT (oad 6 Ω VDC 2 ma max.) E53-CN3N2 E53-CNQ3N2 E53-CN3N2 E53-CN3N2 () () and Control Output 2 () and CT () and CT2 E53-CNQN2 Control Output 2 and CT B (+) A ( ) B (+) A ( ) VDC 2 ma B (+) A ( ) CT B (+) A ( ) CT2 CT VDC 2 ma CT Note: Wire all voltage input terminals correctly. The Controller may fail if voltage input terminals are wired incorrectly.

11 Nomenclature E5CN- Temperature unit Operation indicators No. display No. 2 display evel Key Up Key Mode Key Down Key Dimensions (Unit: mm) Panel Cutout Mounted Separately Group Mounted (48 number of units 2.5) Waterproof Packing (Accessory) Mounting Adapter (Accessory) Terminal Cover (E53-COV7) (Accessory) 6 min Note: The terminal block cannot be removed Group mounting does not allow waterproofing. Recommended panel thickness is to 5mm. Group mounting is not possible in the vertical direction. (Maintain the specified mounting space between Controllers.) To mount the Controller so that it is waterproof, insert the waterproof packing onto the Controller. When two or more Controllers are mounted, make sure that the surrounding temperature does not exceed the allowable operating temperature specified in the specifications. Accessories (Order Separately) USB-Serial Conversion Cable E58-CIFQ (2,) 25 ED indicator,765 (SD) USB connector (type A plug) ED indicator (RD) Serial connector

12 Terminal Cover E53-COV7 Waterproof Packing Y92S-29 (for DIN 48 48) Note: The E53-COV can not be used. Order the Waterproof Packing separately if it becomes lost or damaged. The Waterproof Packing can be used to achieve an IP66 degree of protection. (Deterioration, shrinking, or hardening of the waterproof packing may occur depending on the operating environment. Therefore, periodic replacement is recommended to ensure the level of waterproofing specified in IP66. The time for periodic replacement depends on the operating environment. Be sure to confirm this point at your site. Consider one year a rough standard. OMR shall not be liable for the level of water resistance if the customer does not perform periodic replacement.) The Waterproof Packing does not need to be attached if a waterproof structure is not required. 9. Current Transformers E54-CT dia E54-CT Thru-current (Io) vs. Output Voltage (Eo) (Reference Values) Maximum continuous heater current: 5 A (5/6 z) Number of windings: 4±2 Winding resistance: 8±2 Ω E54-CT Two, 3.5 dia dia. Output voltage (Eo) V (r.m.s.) V 5 z mv kω Ω R = Ω Distortion factor % 3% % dia. 9 µv ma, A 4 4 Thru-current (Io) A (r.m.s.) Two, M3 (depth: 4) E54-CT3 Thru-current (Io) vs. Output Voltage (Eo) (Reference Values) E54-CT3 Accessory Armature Approx. 3 dia. Plug 8 3 Connection Example Armature Plug ead Maximum continuous heater current: A (5/6 z) (Maximum continuous heater current for an OMR Temperature Controller is 5 A.) Number of windings: 4±2 Winding resistance: 8±.8 Ω Output voltage (Eo) V (r.m.s.) V 5 z mv kω 5 Ω Ω 5 Ω R = Ω Distortion factor % 3% % Approx. 6 dia. µv (22) ma, A Thru-current (Io) A (r.m.s.)

13 Adapter Y92F-45 Note:. Use this Adapter when the panel has already been prepared for the 2. The Adapter is available only in black to Fixture (Accessory) Mounted to Panel ( to 8 mm) (to back of ) Програмируем терморегулатор OMR СИТЕЛ ООД - OMR дистрибутор София - бул. Цариградско шосе 3А, ет.3, офис 5 /в Лито Балкан, зад Shell и The Mall/ тел./факс: (2) sofia@sitel-omron.com Плевен - бул. Русе 37А, ет. 3, офис 2 тел./факс: (64) pleven@sitel-omron.com Пловдив - ул. Белград 2, ет. 2, офис (до Новотела) тел./факс: (32) plovdiv@sitel-omron.com Стара Загора - ул. Захарий Княжески 2, ап. 5 тел./факс: (42) starazagora@sitel-omron.com дистрибутор