ELECTRICAL SPECIFICATIONS PARAMETER SYMBOL CONDITION VALUE UNIT. Vs ±5% Vs ±5% Vs ±5%

Transcription

1 Page 1 of RMS Phase Jitter over 12 khz to 20 MHz bandwidth 31 Standard frequencies from 25 MHz to MHz LPECL and LDS Output types SMD package 7.0 x 5.0 mm ELECTRICAL SPECIFICATIONS PARAMETER SYMBOL CONDITION ALUE UNIT Min. Typ. Max. Frequency Range f0 31 standard frequencies, see table MHz Supply oltage s s ±5% s ±5% s ±5% Operating Temperature Ta C C Frequency Stability Δf/f0 Including First Year aging, initial frequency tolerance at 25 C, Frequency stability over temperature range, supply variation, load variation Long Term stability ( Aging ) Δf/Δty Δf/Δty First 25 C C Input oltage High IH Pin 1, E/D or STBY 70%s Input oltage Low IL Pin 1, E/D or STBY 30%s Input Pullup Impedance Zin Pin 1, E/D=High or Low or STBY=High Pin 1, STBY = Low kω MΩ Startup Time T st Measured from the time s reaches its rated minimum value 6 10 ms Resume Time T res Measured from the time STBY pin crosses 50% threshold 6 10 ms Duty Cycle DC %

2 Page 2 of 5 OUTPUT CHARACTERISTICS PARAMETER SYMBOL CONDITION Output termination load 50 OH connected to s 2.0, s ±5% Output Levels Output termination load 50 OL connected to s 2.0, s ±5% ALUE Min Typ. Max UNIT s 1.1 s 0.7 s 1.9 s 1.5 LPECL Output differential voltage swing SWING Current consumption Is Excluding Load termination, s=2.5 or ma E/D current consumption I E/D E/D = Low 35 ma Output Disable Supply leakage I LEAK E/D = Low 1 STBY current I STBY STBY= Low, for all s 100 Maximum Output Current I driver Maximum average current drawn from Out + or Out 30 m Rise / Fall Time Tr / Tf 20% to 80% E/D time RMS Period Jitter RMS Phase Jitter T E/D J P J PH f0=212.5 MHz, for other frequencies T E/D=100 ns + 3 period f0=100 MHz, s= 3.3v or 2.5 f0= MHz, s= 3.3v or 2.5 f0=212.5 MHz, s= 3.3v or 2.5 f0= MHz, integrated bandwidth, 12 KHz to 20 MHz, all s 115 ns LDS PARAMETER SYMBOL CONDITION ALUE Min Typ. Max UNIT Output termination load 100 Output differential voltage OD connected between OUT+ and OUT m, s ±5% Output differential voltage Magnitude change Δ OD 50 m Offset Output oltage OOFF Output termination load 100 connected between OUT+ and OUT , s ±5% Offset Output oltage Magnitude change ΔOOFF 50 m Current consumption Excluding Load termination, Is s=2.5 or ma E/D current consumption I E/D E/D = Low 35 ma Output Disable Supply leakage I LEAK E/D = Low 1 STBY current I STBY STBY= Low, for all s 100 Rise / Fall Time Tr / Tf 20% to 80% E/D time RMS Period Jitter RMS Phase Jitter T E/D J P J PH f0=212.5 MHz, for other frequencies T E/D=100 ns + 3 period f0=100 MHz, s= 3.3v or 2.5 f0= MHz, s= 3.3v or 2.5 f0=212.5 MHz, s= 3.3v or 2.5 f0= MHz, integrated bandwidth, 12 KHz to 20 MHz, all s 115 ns

3 Page 3 of 5 Table 1. List of Supported Frequencies 25 MHz 50 MHz MHz MHz 75 MHz MHz 100 MHz MHz 125 MHz 133 MHz MHz MHz MHz MHz MHz MHz MHz MHz 150 MHz MHz MHz MHz 166 MHz MHz MHz MHz MHz MHz MHz 200 MHz 212.5MHz MECHANICAL DIMENSIONS AND PIN FUNCTIONING Recommended land pattern 7.0± #6 #5 #4 #4 #5 # YXXXX 5.0± #1 #2 #3 #3 #2 # ± PIN SYMBOL FUNCTION 1 E/D STBY 2 GND Electrical Ground 3 NC H or Open: frequency output L: Output is high impedance H or Open: frequency output L: Device goes to sleep mode. Supply current reduces to I STBY No connect, leave it floating or connect to GND for better heat dissipation 4 OUT+ Output Signal 5 OUT Complementary Output signal 6 s Supply oltage Note: Connect a capacitor of 0.1 F or higher value between s and GND

4 Page 4 of 5 ENIRONMENTAL REFLOW PROFILE Soldering MILSTD883F, Method 2003 Moisture Sensitivity Level MSL 1 at 260 C Temperature Cycle JESD22, Method A104 ibration MILSTD883F, Method 2007 Mechanical Shock MILSTD883F, Method 2002 Storage Temperature C REFLOW PROFILE t P TP Rampup Critical Zone T L to T P TL Temp. [ C] TSMAX TSMIN t L Rampdown t S Preheat t[25 C] to Peak Time [sec] Recommended Solder Reflow Profile Temperature Min Preheat T SMIN 150 C Temperature Max Preheat T SMAX 200 C Time (T SMIN to T SMAX) t S sec. Temperature T L 217 C Peak Temperature T P 260 C Rampup rate R UP 3 C/sec max. Rampdown rate R DOWN 6 C/sec max. Time within 5 C of Peak Temperature t P 10 sec. Time t[25 C] to Peak Temperature t[25 C] to Peak 480 sec. Time t L sec.

5 Page 5 of 5 ORDERING INFORMATION SERIES SUPPLY OLTAGE () Frequency Stability TEMP RANGE ( C ) Output Type Enable/ Disable Function OUTPUT FREQUENCY (MHz) CMP702 25: s=2.5 33: s=3.3 XX: s=2.25 to 3.63 A:±10 B:±20 C:±25 D:±50 U: 20~70 : 40~85 1:LPECL 2:LDS E: E/D output S:Standby See table 1 APPROALS Eng. approval, date: SP, 07/19/2016 Created by, date: SP, 07/19/2016 Revision: A