Photocoupler Product Data Sheet LTV-50L series Spec No.: DS Effective Date: 03/22/2016 LITE-ON DCC RELEASE

Size: px

Start display at page:

Download "Photocoupler Product Data Sheet LTV-50L series Spec No.: DS Effective Date: 03/22/2016 LITE-ON DCC RELEASE"

Catherine Shana Summers
6 years ago
Views:

1 Product Data Sheet Spec No.: DS Effective Date: 3/22/216 Revision: B LITE-ON DCC RELEASE BNS-OD-FC1/A4 LITE-ON Technology Corp. / Optoelectronics No.9,Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C. Tel: Fax: /

2 1. DESCRIPTION The consists of a high efficient AlGaAs Light Emitting Diode and a high speed optical detector. This design provides excellent AC and DC isolation between the input and output sides of the Optocoupler. The output of the optical detector features an open collector Schottky clamped transistor. The internal shield ensures high common mode transient immunity. A guaranteed common mode transient immunity is up to 15KV/μs (min.). The Optocoupler operational parameters are guaranteed over the temperature range from -55 C ~ +1 C. 1.1 Features Stretched SO6 High speed 1MBd typical Package creepage at 8mm Compatible with infrared vapor phase reflow and wave soldering process Functional Diagram Pin No. and Internal connection diagram Very high common mode transient immunity: 15K V/μs at VCM = 15 V guaranteed Guarantee performance from temperature range: -55 C to 1 C TTL compatible Open collector output 1. Anode 3. Cathode 4. GND 5. Vo (Output) 6. Vcc Safety approval : UL 1577 recognized with 5 V rms for 1 minute for LTV-5LP and LTV-5LW VDE DIN EN Approved VIORM = 891Vpeak for LTV-5LP A.1μF bypass Capacitor must be connected between Pin 4 and 6. *1 VIORM = 114Vpeak for LTV-5LW 1.2 Applications Truth Table (Positive Logic) Digital signal isolation Communications interface Micro-controller interface Feedback elements in switching power supplies LED ON OFF OUT LOW HIGH Digital isolation for A/D, D/A conversion Digital field 1/12 Part No. :

3 2. PACKAGE DIMENSIONS 2.1 LTV-5LW 2.2 LTV-5LP Notes : 1. Year date code digit work week. 3. Factory identification mark (Y : Thailand) or V for VDE option. * Dimensions are in Millimeters and (Inches). 2/12 Part No. :

4 3. TAPING DIMENSIONS 3.1 LTV-5LW-TA 3.2 LTV-5LW-TA1 3.3 LTV-5LP-TA 3.4 LTV-5LP-TA1 Description Symbol Dimension in mm (inch) For W type Dimension in mm (inch) For P type Tape wide W 16±.3 (.63) 16±.3 (.63) Pitch of sprocket holes P 4±.1 (.16) 4±.1 (.16) Distance of compartment F 7.5±.1 (.3) 7.5±.1 (.3) P 2 2±.1 (.79) 2±.1 (.79) Distance of compartment to compartment P 1 16±.1 (.63) 12±.1 (.47) 3.5 Quantities Per Reel Package Type Quantities (pcs) 1 3/12 Part No. :

5 4. RATING AND CHARACTERISTICS 4.1 Absolute Maximum Ratings Parameter Symbol Min Max Units Note Storage Temperature T ST C Operating Temperature T A C Isolation Voltage V ISO 5 V RMS Supply Voltage V CC V Lead Solder Temperature 26 C 2 Input Average Forward Input Current I F 25 ma Peak Input Current (5% duty cycle, 1 ms pulse width) Peak Transient Input Current (1 μs pulse width, 3 pps) I F 5 ma 3 I F 1. A Reverse Input Voltage V R 5 V Input Power Dissipation P I 45 mw Output Output Collector Current I O 8 ma Peak Output Current I O 16 ma Output Collector Voltage V O V Output Collector Power Dissipation P O 1 mw *Ambient temperature = 25 C, unless otherwise specified. Stresses exceeding the absolute maximum ratings can cause permanent damage to the device. Exposure to absolute maximum ratings for long periods of time can adversely affect reliability. 4/12 Part No. :

6 4.2 Electrical Optical Characteristics Parameters Test Condition Symbol Min Typ Max Units Note Input Input Forward Voltage I F =16mA, T A=25 C V F V Input Reverse Voltage I R = 1μA BV R 5 V Detector * Current transfer ratio I F = 16mA; V CC = 4.5V; T A = 25 C ; V O =.4V I F = 16mA; V CC = 4.5V; T A = 25 C ; V O =.5V CTR % Logic low output voltage output voltage I F = 16mA;V CC = 4.5V; I o = 3.mA; T A = 25 C I F = 16mA;V CC = 4.5V; I o = 2.4mA; T A = 25 C V OL V I F = ma, V O = V CC = 5.5V, T A = 25 C.2.5 Logic high output current I F = ma, V O = V CC = 15V T A = 25 C I OH.5 1 T A = ~ 7 C 5 μa Logic low supply current Logic high supply current I F = 16mA, V o = open (V CC=3V) I F = ma, V o = open ; T A = 25 C (V CC = 3V) I CCL 165 I CCH.2 1 *All Typical values at T A = 25 C unless otherwise specified. All minimum and maximum specifications are at recommended operating condition. *Current Transfer Ratio in percent is defined as the ratio of output collector current, I O, to the forward LED input current, I F, times 1%. 5/12 Part No. :

7 5. SWITCHING SPECIFICATION Parameter Test Condition Symbol Min Typ Max Units Note Propagation Delay Time to Low Output Level T A = 25 C 19 8 t PHL ~ 1 C 8 5 R L=1.9KΩ ns Propagation Delay Time to High Output Level T A = 25 C 15 8 t PLH ~ 1 C 8 4 Logic High Common Mode Transient Immunity I F = ma;v CM = 15Vp-p; C L = 15 pf; T A=25 C, R L=1.9KΩ CM H KV/μs 6 Logic Low Common Mode Transient Immunity I F = 16mA;V CM = 15Vp-p C L = 15 pf; T A = 25 C, R L = 1.9KΩ CM L KV/μs 7 *All Typical values at T A = 25 C unless otherwise specified. All minimum and maximum specifications are at recommended operating condition. 6/12 Part No. :

8 6. ISOLATION CHARACTERISTIC Parameter Test Condition Symbol Min Typ Max Units Note Input-Output Insulation Leakage Current Withstand Insulation Test Voltage 45% RH, t = 5s, V I-O = 3kV DC, T A = 25 C RH 5%, t = 1min, T A = 25 C I I-O 1. μa 8 V ISO 5 V rms 8,9 Input-Output Resistance V I-O = 5V DC R I-O 1 12 Ω 8 *All Typical values at T A = 25 C unless otherwise specified. All minimum and maximum specifications are at recommended operating condition. NOTES: 1) A.1µF or bigger bypass capacitor for V CC is needed. 2) 26 C for 1 seconds 3) Peaking driving circuit may be used to speed up the LED. The peak drive current of LED may go up to 5mA and maximum pulse width 5ns, as long as average current doesn t exceed 2mA. 4) t PLH (propagation delay) is measured from the 3.75 ma point on the falling edge of the input pulse to the 1.5 V point on the rising edge of the output pulse. 5) t PHL (propagation delay) is measured from the 3.75 ma point on the rising edge of the input pulse to the 1.5 V point on the falling edge of the output pulse. 6) CM H is the maximum tolerable rate of rise of the common mode voltage to assure that the output will remain in a high logic state 7) CM L is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state 8) Device is considered a two-terminal device: pins 1, 2, 3 shorted together, and pins 4, 5, 6 shorted together. 9) In accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage 6 V rms for one second (leakage current less than 1 ua). 7/12 Part No. :

9 Normalized Current Transfer Ratio t P - Propagation Delay - ns t P - Propagation Delay - ns Normalized Current Transfer Ratio I O - Output Current - ma I F - Forward Current - ma Photocoupler 7. TYPICAL PERFORMANCE CURVES & TEST CIRCUITS T A = 25 o C V CC = 5V 4mA 35mA 3mA 25mA 2mA 15mA 1mA I F = 5mA V O - Output Voltage - V T A = 25 o C V F - Forward Voltage - V Figure 1: DC and Pulsed Transfer Characteristics Figure 2: Input Current vs. Forward Voltage 6 5 I F = 1mA I F = 16mA t PLH t PHL 1 1 R L - Load Resistance - kω.6.4 Normalized to I F = 16mA V O =.4V.2 V CC = 5V T A = 25 o C I F - Forward Current - ma Figure 3: Propagation Delay vs. Load Resistance. Figure 4: Current Transfer Ratio vs. Input Current I F = 16mA, V CC = 5.V R L = 1.9KΩ Normalized to I F = 16mA V.2 O =.4V V CC = 5V T A = 25 o C T A - Ambient Temperature - o C Figure 5: Current Transfer Ratio vs. Temperature t PLH t PHL T A - Ambient Temperature - o C Figure 6: Propagation Delay Time vs. Temperature. 8/12 Part No. :

10 I OH - Logic High Output Current - na Normalized Response - db Photocoupler 1 1 I F = V O = V CC = 5.V T A = 25 o C I F = 16mA V CC = 5.V R L = 1Ω R L = 22Ω R L = 47Ω R L = 1KΩ T A - Temperature - o C f - Frequency - MHz Figure 7: Logic High Output Current vs. Temperature. Figure 8: Frequency Response IF VO Vcc PULSE GEN. Z O = 5Ω tr = 5 ns I F 1% DUTY CYCLE 1/f < 5us RL Vcc VO tphl VTHHL VTHLH tp LH VOL I F MONITOR RM uf CL Figure 9: Switching Test Circuit I F VCM V 1% 9% tr 1V tf VFF B A RL Vcc VO VO SW A: IF=mA 5V uf CL VO SW B: IF=3mA VOL VCM + - PULSE GEN. Figure 1: Test Circuit for Transient Immunity and Typical Waveforms 9/12 Part No. :

11 Temperature ( C) Photocoupler 8. TEMPERATURE PROFILE OF SOLDERING 8.1 IR Reflow soldering (JEDEC-STD-2C compliant) One time soldering reflow is recommended within the condition of temperature and time profile shown below. Do not solder more than three times. Profile item Conditions Preheat - Temperature Min (T Smin) - Temperature Max (T Smax) - Time (min to max) (ts) 15 C 2 C 9±3 sec Soldering zone - Temperature (T L) - Time (t L) Peak Temperature (T P) Ramp-up rate Ramp-down rate 217 C 6 ~ 1 sec 26 C 3 C / sec max. 3~6 C / sec Ramp-up TL 217 C Tsmax 2 C 2 sec TP 26 C Ramp-down Tsmin 15 C 6-1 sec tl (Soldering) 25 C 6 ~ 12 sec ts (Preheat) Time (sec) 1/12 Part No. :

12 8.2 Wave soldering (JEDEC22A111 compliant) One time soldering is recommended within the condition of temperature. Temperature: 26+/-5 C Time: 1 sec. Preheat temperature:25 to 14 C Preheat time: 3 to 8 sec. 8.3 Hand soldering by soldering iron Allow single lead soldering in every single process. One time soldering is recommended. Temperature: 38+/-5 C Time: 3 sec max. 11/12 Part No. :

13 9. NAMING RULE Part number Options LTV-5LP-TA LTV-5LP-TA1 LTV-5LW-TA LTV-5LW-TA1 LTV5LPTA-V LTV5LPTA1-V LTV5LWTA-V LTV5LWTA1-V Definition of Suffix "5L" "P" "W" "TA" "TA1" "V" Remark LiteOn model name clearance distance 7mm minimum clearance distance 8mm minimum Pin 1 location at lower right of the tape Pin 1 location at upper left of the tape VDE approved option 1. NOTES LiteOn is continually improving the quality, reliability, function or design and LiteOn reserves the right to make changes without further notices. The products shown in this publication are designed for the general use in electronic applications such as office automation equipment, communications devices, audio/visual equipment, electrical application and instrumentation. For equipment/devices where high reliability or safety is required, such as space applications, nuclear power control equipment, medical equipment, etc, please contact our sales representatives. When requiring a device for any specific application, please contact our sales in advice. If there are any questions about the contents of this publication, please contact us at your convenience. The contents described herein are subject to change without prior notice. Immerge unit s body in solder paste is not recommended. 12/12 Part No. :

Photocoupler Product Data Sheet LTV-M501 Spec No.: DS Effective Date: 06/07/2016 LITE-ON DCC RELEASE

Photocoupler Product Data Sheet LTV-M501 Spec No.: DS Effective Date: 06/07/2016 LITE-ON DCC RELEASE Product Data Sheet LTV-M5 Spec No.: DS7-23-9 Effective Date: 6/7/26 Revision: B LITE-ON DCC RELEASE BNS-OD-FC/A4 LITE-ON Technology Corp. / Optoelectronics No.9,Chien Road, Chung Ho, New Taipei City 23585,