ELECTRICAL SPECIFICATIONS PARAMETER SYMBOL CONDITION VALUE UNIT. 52 standard frequencies between 3.57MHz and MHz

Transcription

1 Frequency Oscillator Page 1 of 6 Low Power Consumption of 3.5 typical at Standard frequencies between 3.57MHz and MHz HCMOS/ LCMOS compatible output SMD package 2.0 x 1.6 mm ELECTRICAL SPECIFICATIONS PARAMETER SYMBOL CONDITION ALUE UNIT Frequency Range f0 52 standard frequencies between 3.57MHz and MHz Min. Typ. Max MHz Supply oltage s s ±5% Supply Current Operating Temperature Frequency Stability Enable / Disable/ Standby Function Is Ta Δf/f0 E/D/St s = 1.8, f0=20mhz, no load s = 2.5, f0=20mhz, no load s = 2.8, f0=20mhz, no load s = 3.3, f0=20mhz, no load Including First Year aging, initial frequency tolerance at 25 C, Frequency stability over temperature range, supply variation, load variation Enable = Open or 1 (IH 0.75s) ( output signal active ) Disable = GND or 0 (IL<0.25s ) ( output high impedance, oscillator operates ) Standby = GND or 0 IL<0.25s ) ( output weakly pulled down, oscillator sleep mode ) s s 0.25s Enable / Disable Time T E/D f0=110mhz 130 ms C C ppm ppm ppm Enable / Disable Current I E/D s=1.8, E/D =GND s=2.5 to 3.3, E/D =GND Output in high impedance state Standby Current Istby STBY=GND,s=1.8 STBY=GND,s=2.5 STBY=GND,s=2.8 to 3.3 Output is weakly pulled down Startup Time T ST 5 ms RMS Phase Jitter J PH f0=75mhz,bw 900KHz to 7.5MHz f0=75mhz,bw 12KHz to 20MHz RMS Period Jitter J P f0=75mhz Peak to Peak Period Jitter J PK-PK f0=75mhz,s=2.5 to 3.3 f0=75mhz, s=

2 Frequency Oscillator Page 2 of 6 OUTPUT CHARACTERISTICS LCMOS PARAMETER SYMBOL CONDITION Output Levels OH OL Ioh= -2 ( s=1.8 ) Ioh= -3 ( s= 2.5 or 2.8 ) Ioh= -4 ( s=3.0 or 3.3 ) Iol=2 ( s=1.8 ) Iol=3 ( s= 2.5 or 2.8 ) Iol=4 ( s=3.0 or 3.3 ) ALUE Min Typ. Max UNIT 0.9 s Duty Cycle DC 50% Output level % 0.1s Output Load O CL Ta=25 C pf Table 1. Rise/Fall Time vs. CLoad ( CL ), s=1.8 D0, default D D D D D D D Table 2. Rise/Fall Time vs. CLoad ( CL ), s=2.5 D D D2, default D D D D D

3 Frequency Oscillator Page 3 of 6 CMC202-SERIES Table 3. Rise/Fall Time vs. CLoad ( CL ), s=2.8 D D D2, default D D D D D Table 4. Rise/Fall Time vs. CLoad ( CL ), s=3.0 D D D D3, default D D D D Table 5. Rise/Fall Time vs. CLoad ( CL ), s=3.3 D D D D3, default D D D D Table 6. List of Supported Frequencies 3.57 MHz 4 MHz MHz 6 MHz MHz MHz 10 MHz 12 MHz 14 MHz MHz 19.2 MHz 20 MHz 24 MHz MHz 25 MHz MHz 26 MHz 27 MHz MHz 30 MHz MHz MHz 33 MHz 33.3 MHz 33.33MHz MHz MHz MHz 35.84MHz 37.5 MHz 38 MHz 38.4 MHz 40 MHz 40.5MHz 48 MHz 50 MHz 54 MHz 60 MHz 62.5 MHz 65 MHz 66 MHz 66.6 MHz MHz MHz MHz MHz 72 MHz MHz MHz MHz 75 MHz MHz

4 Frequency Oscillator Page 4 of 6 MECHANICAL DIMENSIONS AND PIN FUNCTIONING RECONMENDED LAND PATTERN BOTTOM IEW PIN SYMBOL FUNCTION 1 E/D/STBY/N H :Enable output frequency L:Disable output frequency, high impedance In E/D or STBY mode connect a pull-up resistor of 10kΩ to pin 1, in case not externally driven. In case pin1 is left floating, use N option 2 GND Electrical Ground 3 OUTPUT Output Signal 4 s Supply oltage Note: Connect a capacitor of 0.1 F or higher value between s and GND

5 Frequency Oscillator Page 5 of 6 ENIRONMENTAL REFLOW PROFILE Soldering MIL-STD-883F, Method 2003 Moisture Sensitivity Level MSL 1 at 260 C Temperature Cycle JESD22, Method A104 ibration MIL-STD-883F, Method 2007 Mechanical Shock MIL-STD-883F, Method 2002 Storage Temperature C REFLOW PROFILE t P TP Ramp-up Critical Zone T L to T P TL Temp. [ C] TSMAX TSMIN t L Ramp-down t S Preheat t[25 C] to Peak Time [sec] Recommended Solder Reflow Profile Temperature Min Preheat T SMIN 150 C Temperature Max Preheat T SMAX 200 C Time (T SMIN to T SMAX) t S sec. Temperature T L 217 C Peak Temperature T P 260 C Ramp-up rate R UP 3 C/sec max. Ramp-down rate R DOWN 6 C/sec max. Time within 5 C of Peak Temperature t P 10 sec Time t[25 C] to Peak Temperature t[25 C] to Peak 480 sec. Time t L sec.

6 Frequency Oscillator Page 6 of 6 ORDERING INFORMATION SERIES SUPPLY OLTAGE () Frequency Stability TEMP RANGE ( C ) Output Drive Enable/ Disable Function - OUTPUT FREQUENCY (MHz) 1:D0 CMC202 18:s=1.8 25: s=2.5 28: s=2.8 30: s=3.0 33: s=3.3 XX: s=2.5-10% to % A:±20ppm B:±25ppm C:±50ppm U: -20~70 : -40~85 2:D1 3:D2 4:D3 5:D4 6:D5 7:D6 8:D7 See table 1 to 5 E: E/D output S:Standby N: No connect - See table 6 APPROALS Eng. approval, date: SP, 07/05/2016 Created by, date: SP, 07/05/2016 Revision: A