Preliminary. Electrical Characteristics Characteristic Sym Notes Min Typ Max Units

Transcription

1 Preliminary SF1202D CDM 450 F-and RF SW Filter 3.8 x 3.8 x 1.4 mm Surface-mount Package Complies with Directive 2002/95/EC (RoHS) bsolute Maximum Ratings Rating Value Units Maximum Incident Power in Passband +28 dm Maximum DC voltage between any Two Terminals 30 VDC Storage Temperature Range -40 to +85 C Suitable for Lead-free Soldering - Maximum Soldering Profile 260 C for 30 s Pb MHz SW Filter SM Electrical Characteristics Characteristic Sym Notes Min Typ Max Units Nominal 1 d Center Frequency f C MHz Passband Insertion Loss to MHz IL d VSWR to MHz 1.6:1 2:1 Rejection 0.3 to MHz to MHz to MHz, +15 to +40 C , 2, to MHz d to 1200 MHz to 1700 MHz MHz Operating Temperature Range T C Impedance at f c Source, single ended 50 ohm Load, single ended 50 ohm Case Style SM x 3.8 mm Nominal Footprint Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator 602, YWWS Standard Reel Quantity Reel Size 7 Inch 1000 Pieces/Reel Reel Size 13 Inch 3000 Pieces/Reel Electrical Connections Connection Terminals Port 1 2 Port 2 5 Case Ground ll others CUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. 2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. 3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PC layout and external impedance matching design. See pplication Note No. 42 for details. 4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." 5. The design, manufacturing process, and specifications of this filter are subject to change. 6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. 7. US and international patents may apply. 8. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. info@rfm.com Page 1 of 5

2 Passband Plot Wideband Plot Page 2 of 5

3 VSWR S11 and S22 Plots Page 3 of 5

4 REF. "" REF. Tape and Reel Specifications Nominal Size Quantity Per Reel Inches millimeters See Detail "" COMPONENT ORIENTTION and DIMENSIONS Carrier Tape Dimensions o o Ko Pitch W 4.25 mm 4.25 mm 1.30 mm 8.0 mm 12.0 mm 0.3 ± 0.05 PIN # RO.3 (MX.) o Ko SECTION - o SECTION - Pitch 1.5 R0.5 (MX.) USER DIRECTION OF FEED info@rfm.com Page 4 of 5

5 0.129 REF. (3.28) TYP. (1.27) TYP. (0.74) SM Case 6-Terminal Ceramic Surface-Mount Case 3.8 X 3.8 mm Nominal Footprint Case Dimensions REF. (4.47) (0.91) Dimension mm Inches Min Nom Max Min Nom Max C D E G H I J Electrical Connections (1.68) Connection Terminals Port 1 Single Ended Input 2 Port 2 Single Ended Output 5 Ground ll others Single Ended Operation Only Dot indicates Pin 1 PC Footprint TYP. (1.40) Solder Pad Termination Lid ody Materials u plating µinches ( µm) over µinches ( µm) Ni. Fe-Ni-Co lloy Electroless Nickel Plate (8-11% Phosphorus) µinches Thick l 2 O 3 Ceramic Pb Free TOP VIEW OTTOM VIEW C G H YWWS 5 4 E I D J info@rfm.com Page 5 of 5