Insertion loss (db) Return Loss (db) 4x x x Orientation Marker Denotes Pin Location

Transcription

1 Model DC1722J55AHF Ultra Low Profile 85 5 db Directional Coupler Detailed Electrical Specifications: Specifications subject to change without notice. Description The DC1722J55AHF is a low cost, low profile sub-niature high performance 5 db directional coupler in an easy to use RoHS compliant, Halogen Free surface mount package. It is designed for 17 22MHz applications including: WCDMA, CDMA, IMT2, UMTS and GSM18 / 19 applications. The DC1722J55AHF is ideal for power detection, signal injection and other applications where low insertion loss signal monitoring is required. The DC1722J55AHF is available on tape and reel for pick and place high volume manufacturing. All of the Xinger components are constructed from cerac filled PTFE composites which possess excellent electrical and mechanical stability. All parts have been subjected to rigorous qualification testing and units are 1% RF tested. Features: MHz Mean Coupling 5dB Ultra Low Insertion Loss WCDMA,IMT2,UMTS, GSM LTE Bands:1,2,3,4,9,1, 33,34,35,36,37,39 Tape & Reel RoHS Compliant Halogen Free 1% RF Tested 5 C to 85 C Frequency (MHz) Mean Coupling Insertion loss ROOM (25 C) Return Loss Phase Balance (deg) Frequency Sensitivity Power Handling (watts) Min Typ. Max Typ. Max Typ. Min Typ. Min Typ. Max Typ. Max Max **Specification based on performance of unit properly installed on crostrip printed circuit boards with 5 Ω nonal impedance. Outline Drawing Top View (Nearside) Bottom View (Farside) 2.4±.1.8±.8 4x x x ±.1 6x.98 6x.22 Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location x.3 Pin Configuration-1 Configuration-2 Configuration Configuration-4 1 Input Isolated Direct Coupled 2 GND GND GND GND 3 Isolated Input Coupled Direct 4 Direct Coupled Input Isolated 5 GND GND GND GND 6 Coupled Direct Isolated Input Mechanical Outline -Dimensions are in Millimeters -Tolerances are Non-Cumulative (315) (8)

2 Model DC1722J55AHF Typical Performance: 16 MHz. to 23 MHz (Configuration 1) 3 Return Loss at Input Port Insertion Loss Coupling -1 [degree] Phase Balance (315) (8)

3 Model DC1722J55AHF Wideband Performance: 1 to 81MHz (Configuration 1) 3 Return Loss at Input Port Insertion Loss Coupling [degree] Phase Balance (315) (8)

4 Model DC1722J55AHF Definition of Measured Specifications Parameter Return Loss Insertion Loss Mean Coupling Phase Balance Frequency sensitivity Definition The impedance match of the coupler to a 5Ω system. Return Loss is an alternate means to express VSWR. The power at the isolated port divided by the power at the coupled port The input power divided by the sum of the power at the two output ports. At a given frequency ( ω ), coupling is the input power divided by the power at the coupled port. Mean coupling is the average value of the coupling values in the band. N is the number of frequencies in the band. The difference in phase angle between the two output ports. The decibel difference between the maximum in band coupling value and the nimum in band coupling value. n Mathematical Representation i, j, k, m is denoted as the port index of input, isolated, direct and coupled port for specific pin configuration shown in the table above 2 log ( S ) 1 2 log 1 1 ii S S ji 2 2 1log ( S + S ) Coupling = 2 log1 S Mean Coupling = N m= 1 ki 2log S S + 9 o ki (Max Coupling Min Coupling )/2 N 1 S (315) (8)

5 Model DC1722J55AHF Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transssion lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from organic PTFE based composites which possess excellent electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transssion line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. 6x.35 4x.3 6x x.5 4x Transssion Line Plated thru holes to ground Circuit Pattern Footprint Pad (s) Solder Resist Dimensions are in Millimeters Mounting Footprint (315) (8)

6 Model DC1722J55AHF Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-D. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4 per reel. (315) (8)