MHz BAW Filter

Transcription

1 Applications Satellite Radio antenna modules Satellite Radio devices Suitable for Automotive applications Compliant to the AECQ0 Grade 2 reliability standard CSP 1713, 1.7 X 1.3 X 6 mm Product Features Temperaturecompensated bandpass filter Enables Coexistence of SDARS and WCS radios Low Loss in full SDARS Radio Channel MHz band High Rejection in the MHz band: WCS Lower High Rejection in MHz band: WCS Upper Industryleading small size: 1.7 x 1.3 x.46 mm + 24 dbm (CW) power handling (min) Performance across 40 to + ºC Operable to + 12 ºC Singleended operation Ceramic chipscale package (CSP) Hermetically sealed package RoHS compliant, Pbfree General Description is a highperformance, highpower Bulk Acoustic Wave (BAW) filter with extremely steep skirts and a 2 MHz pass band. is specifically designed to enable coexistence of SDARS and WCS signals within the same device or in close proximity to one another. The part passes the entire SDARS band, covering MHz. The uses advanced and inexpensive packaging techniques to achieve an industryleading 1.7 x 1.3 x.46 mm package. The filter exhibits excellent power handling capabilities. Functional Block Diagram Top View Pin Configuration Single Ended EEEnded./BalB Pin No Label 9 Input 6 Output 7, 8 Ground 1,2,3,4,,7,8, Ground (1) 1. see pg 3 for ground considerations Ordering Information Part No. Description Product description EVB2 Evaluation board description pg3 Standard T/R size =,000 units/reel Data Sheet: Rev C of 6 Disclaimer: Subject to change without notice 1 TriQuint /

2 Electrical Specifications (1,3) Test conditions unless otherwise noted: Temp= 40 C to + C (2,3) Parameter Conditions Min Typ (2) Max Units Center Frequency Fc of RF Filter MHz Maximum Insertion Loss MHz db Passband 3.0 db Bandwidth Fc = MHz 31 MHz Amplitude Ripple PB1 PB2 PB3 PB4 PB PB6 PB7 PB8 PB9 Group Delay Ripple PB1 PB2 PB3 PB4 PB PB6 PB7 PB8 PB9 Input Return Loss Output Return Loss Relative Attenuation (4) (FM) (WCS ALower) (WCS BLower) (WCS BLower) (6) (WCS AUpper) (WCS BUpper) MHz (TDM1) MHz (COFDM) MHz (TDM2) MHz (SAT1A) MHz (SAT2A) MHz (TERRA) MHz (TERRB) MHz (SAT2B) MHz (SAT1B) MHz (TDM1) MHz (COFDM) MHz (TDM2) MHz (SAT1A) MHz (SAT2A) MHz (TERRA) MHz (TERRB) MHz (SAT2B) MHz (SAT1B) MHz 88 8 MHz MHz MHz 00 MHz MHz MHz (40 to +8 C) MHz (+8 to + C) MHz MHz MHz db pp ns pp db dbc Input and Output Impedance () 0 1. All specifications are based on the TriQuint schematic for reference design shown on page Typical values are based on average measurements at + 2 C. 3. In production, devices will be tested at room temperature to a guardbanded specification; this limit is based on average performance over temperature. 4. Attenuation is defined from the insertion loss level measured at the center frequency Fc.. This is the optimum impedance in order to achieve the performance shown. 6. Extended temperature derated specification as noted. Data Sheet: Rev C of 6 Disclaimer: Subject to change without notice 1 TriQuint /

3 Absolute Maximum Ratings Parameter Rating Storage Temperature (1) 40 to + 12 C Operable Temperature (2) 40 to +12 C RF Input Power (3) + 24 dbm 1. Operation of this device outside the parameter ranges given may cause permanent damage 2. Specifications are not guaranteed over all operable conditions 3. Input Power with applied CW signal equivalent to + C for k hours Reference Design Top View zoomed in 9.1nH pf ,2,3,4,7, Impedance matching required (series tank) 2. Trace width nominal 0 Ohms 3. PCB:.80 x.80 x.062; Construction ( layer stackup): ½ oz Cu Top Layer; Dielectric: Taconic TLYA (.007); ½ oz Cu Middle Layer, FR4; ½ oz Cu Bottom Layer; total thickness (0.062) (dimensions are in inches). Contact TriQuint for Gerber files Bill of Material EVB Design Reference Des. Value Description Manuf. Part Number U1 N/A CSP 1713, MHz Baw Filter TriQuint Fl L1 9.1 nh 01 chip Inductor, +/ 3% Murata LQP03TN9N1H02 C1 pf 0 chip cap, +/ 0.04 pf Murata GRM022C1CR40BD0D SMA N/A SMA connector Radiall USA Inc. PCB N/A PC board Multiple 9664 PCB Mounting Pattern All dimensions are in millimeters. Angles are in degrees. 2. This drawing specifies the mounting pattern used on the TriQuint evaluation board for this product. Some modification may be necessary to suit end user assembly materials and processes Data Sheet: Rev C of 6 Disclaimer: Subject to change without notice 1 TriQuint /

4 Performance Plots Reference Design Test conditions unless otherwise noted: Temp= + 2 C Data Sheet: Rev C of 6 Disclaimer: Subject to change without notice 1 TriQuint /

5 Package Information, Marking and Dimensions Marking code MFG site Package Style: CSP1713 Dimensions: 1. x 1.30 x 6 mm 19 M WWY Body: Al 2 O 3 ceramic Lid: Kovar or Alloy 42, Au over Ni plated Terminations: Au plating μm, over a 26 μm Ni plating ID dot Date code All dimensions shown are nominal in millimeters All tolerances are ± 0.1 mm except overall length and width ± 0. mm 6 NOM. 0.0 MAX All dimensions shown are typical in millimeters 2. An asterisk (*) in front of the marking code indicates prototype Tape and Reel information Standard T/R quantity =,000 units/reel Ø330 ID dot SECTION BB 0. A SECTION AA A MAX. TYP. 1. B 1.7 Ø2 Ø.2 Ø Direction of travel B Data Sheet: Rev C of 6 Disclaimer: Subject to change without notice 1 TriQuint /

6 Product Compliance Information ESD Sensitivity Ratings Caution! ESDSensitive Device ESD Rating: Class 1C Test Human Body Model (HBM) Standard ESDA/JEDEC JS001 ESD Rating: Class C3 Test: Charge Device Model (CDM) Standard: ESDA/JEDEC JES002 MSL Rating Not applicable. Hermetic package. Solderability Compatible with both leadfree (2 C maximum reflow temperature) and tin/lead (24 C maximum reflow temperature) soldering processes. Refer to Soldering Profilefor recommended guidelines. RoHs Compliance This part is compliant with EU 02/9/EC RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and Electronic Equipment). This product also has the following attributes: Lead Free Halogen Free (Chlorine, Bromine) Antimony Free TBBPA (C 1 H 12 Br ) Free PFOS Free SVHC Free Contact Information For the latest specifications, additional product information, worldwide sales and distribution locations, and information about TriQuint: Web: Tel: infosales@tqs.com Fax: For technical questions and application information: flapplication.engineering@tqs.com Important Notice The information contained herein is believed to be reliable. TriQuint makes no warranties regarding the information contained herein. TriQuint assumes no responsibility or liability whatsoever for any of the information contained herein. TriQuint assumes no responsibility or liability whatsoever for the use of the information contained herein. The information contained herein is provided "AS IS, WHERE IS" and with all faults, and the entire risk associated with such information is entirely with the user. All information contained herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for TriQuint products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. TriQuint products are not warranted or authorized for use as critical components in medical, lifesaving, or lifesustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death. Data Sheet: Rev C of 6 Disclaimer: Subject to change without notice 1 TriQuint /