Is Now Part of. To learn more about ON Semiconductor, please visit our website at

Transcription

1 Is Now Part of To learn more about ON Semiconductor, please visit our website at Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers will need to change in order to meet ON Semiconductor s system requirements. Since the ON Semiconductor product management systems do not have the ability to manage part nomenclature that utilizes an underscore (_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated device numbers. The most current and up-to-date ordering information can be found at Please any questions regarding the system integration to Fairchild_questions@onsemi.com. ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor s product/patent coverage may be accessed at ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. Typical parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customer s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

2 FOD8163, FOD8163T 3.3 V / 5 V, Mbit/sec, Logic Gate Optocoupler in Stretched Body SOP 6-Pin Features 8 mm Creepage and Clearance Distance, and.4 mm Insulation Distance to Achieve Reliable and High Voltage Insulation High Noise Immunity Characterized by Common Mode Transient Immunity (CMTI) kv/ s Minimum CMTI Specifications Guaranteed Over 3 V to 5.5 V Supply Voltage and -4 C to C Extended Industrial Temperature Range High-Speed, Mbit/s Data Rate (NRZ) Safety and Regulatory Approvals UL1577, 5, VAC RMS for 1 Minute DIN-EN/IEC , 1,14 V Peak Working Immunity Insulation Voltage Applications Isolating Intelligent Power Module Isolating Industrial Communication Interface Related Resources Description March 16 The FOD8163 series is a 3.3 V / 5 V high-speed logic gate optocoupler with open-collector output, which supports isolated communications allowing digital signals to communicate between systems without conducting ground loops or hazardous voltages. The FOD8163 series utilizes stretched body package to achieve 8 mm creepage and clearance distances (FOD8163T), and optimized IC design to achieve reliably high-insulation voltage and high-noise immunity. The FOD8163 series consists of an aluminium gallium arsenide (AlGaAs) light emitting diode and an integrated high-speed photodetector. The output of the detector IC is an open collector schottky-clamped transistor. The electrical and switching characteristics are guaranteed over the extended industrial temperature range of -4 C to C and a range of 3 V to 5.5 V. Functional Schematic ANODE NC CATHODE 1 3 Figure 1. Functional Schematic V O GND Figure. Package Outline FOD8163, FOD8163T Rev. 1.1

3 Truth Table LED V O Off HIGH On LOW Pin Definitions Pin # Name Description 1 ANODE Anode NC Not Connected 3 CATHODE Cathode 4 GND Output Ground 5 V O Output Voltage 6 Output Supply Voltage Pin Configuration ANODE NC CATHODE Figure 3. Pin Configuration V O GND FOD8163, FOD8163T Rev. 1.1

4 Safety and Insulation Ratings As per DIN EN/IEC , this optocoupler is suitable for safe electrical insulation only within the safety limit data. Compliance with the safety ratings shall be ensured by means of protective circuits. Parameter Installation Classifications per DIN VDE 1/1.89 Table 1, For Rated Mains Voltage FOD8163 Characteristics FOD8163T < 15 V RMS I IV I IV < 3 V RMS I IV I IV < 45 V RMS I III I IV < 6 V RMS I III I III Climatic Classification 4//1 4//1 Pollution Degree (DIN VDE 1/1.89) Comparative Tracking Index Symbol V PR Parameter Input-to-Output Test Voltage, Method B, V IORM x = V PR, % Production Test with t m = 1 s, Partial Discharge < 5 pc Input-to-Output Test Voltage, Method A, V IORM x 1.6 = V PR, Type and Sample Test with t m = s, Partial Discharge < 5 pc FOD8163 Value FOD8163T Unit 1,671,137 V peak 1,46 1,84 V peak V IORM Maximum Working Insulation Voltage 891 1,14 V peak V IOTM Highest Allowable Over-Voltage 6, 8, V peak External Creepage mm External Clearance mm DTI Distance Through Insulation (Insulation Thickness).4.4 mm Safety Limit Values Maximum Values Allowed in the Event of a Failure, T S Case Temperature C I S,INPUT Input Current ma P S,OUTPUT Output Power 6 6 mw R IO Insulation Resistance at T S, V IO = 5 V 9 9 FOD8163, FOD8163T Rev

5 Absolute Maximum Ratings Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. = 5 C unless otherwise specified. Symbol Parameter Value Unit T STG Storage Temperature -4 to +15 C T OPR Operating Temperature -4 to + C T J Junction Temperature -4 to +15 C T SOL Lead Solder Temperature (Refer to Reflow Temperature Profile) 6 for sec C Input Characteristics Average Forward Input Current 5 ma V R Reverse Input Voltage 5. V PD I Input Power Dissipation (1) 45 mw Output Characteristics Supply Voltage to 7. V V O Output Voltage -.5 to +.5 V I O Average Output Current 5 ma PD O Output Power Dissipation (1) 85 mw Note: 1. No derating required up to C. Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to absolute maximum ratings. Symbol Parameter Min. Max. Unit Ambient Operating Temperature -4 + ºC Supply Voltages () V V FL Logic Low Input Voltage.8 V L Logic Low Input Current 5 A H Logic High Input Current ma N Fan Out (at R L = 1 k ) 5 TTL loads R L Output Pull-up Resistor 33 4 Note:..1 F bypass capacitor must be connected between pins 4 and 6. FOD8163, FOD8163T Rev

6 Isolation Characteristics Apply over all recommended conditions, typical value is measured at = 5 C. Symbol Parameter Conditions Min. Typ. Max. Unit V ISO Input-Output Isolation Voltage Notes: 3. Device is considered a two-terminal device: pins 1, and 3 are shorted together and pins 4, 5, and 6 are shorted together. 4. 5, VAC RMS for 1-minute duration is equivalent to 6, VAC RMS for 1-second duration. Electrical Characteristics = 5 C, R.H. < 5%, t = 1. min, I I-O A (3)(4) 5, VAC RMS R ISO Isolation Resistance V I-O = 5 V (3) 11 C ISO Isolation Capacitance V I-O = V, frequency = 1. MHz (3) 1. pf Apply over all recommended conditions; = -4 C to + C, 3. V 5.5 V; unless otherwise specified. Typical value is measured at = 5 C and = 3.3 V or = 5 V. Symbol Parameter Conditions Min. Typ. Max. Unit Figure Input Characteristics V F Forward Voltage V 4 Temperature Coefficient = ma (V F / ) -1.8 mv/ C of Forward Voltage Input Reverse BV R I Breakdown Voltage R = A 5. V HL Threshold Input Current Output Characteristics Logic Low Output V OL Voltage I OH I CCL I CCH Logic High Output Current Logic Low Output Supply Current Logic High Output Supply Current V O =.6 V, I OL (sink) = 13 ma = rated HL, I OL (sink) = 13 ma. 6. ma V 6 = 5 A, V O = 3.3 V A 7 = 5 A, V O = 5. V A 7 = ma, = 3.3 V ma 8, = ma, = 5. V 7.1. ma 8, = ma, = 3.3 V ma 9, = ma, = 5. V ma 9, FOD8163, FOD8163T Rev

7 Switching Characteristics Apply over all recommended conditions; = -4 C to + C, 3.3 V 5 V, = 6. ma; unless otherwise specified. Typical value is measured at = 5 C and = 3.3 V. Symbol Parameter Conditions Min. Typ. Max. Unit Figure Data Rate R L = 35 Mbit/sec t PHL t PLH Propagation Delay to Logic Low Output Propagation Delay to Logic High Output R L = 35, C L = 15 pf 4 8 ns R L = 35, C L = 15 pf 53 9 ns 11, 13, 16 11, 13, 16 PWD Pulse Width Distortion, 1, 14, R t PHL t PLH L = 35, C L = 15 pf ns 16 t PSK Propagation Delay Skew R L = 35, C L = 15 pf (5) 4 ns t R Output Rise Time (% to 9%) R L = 35, C L = 15 pf ns 15, 16 t F Output Fall Time (9% to %) R L = 35, C L = 15 pf ns 15, 16 CM H CM L Common-Mode Transient Immunity at Output High Common-Mode Transient Immunity at Output Low = ma, V O > V, V CM = 15 V (6) 4 kv/ s 17 = 6. ma, V O <.8 V, V CM = 15 V (6) 4 kv/ s 17 Notes: 5. t PSK is equal to the magnitude of the worst-case difference in t PHL and/or t PLH between any two units from the same manufacturing date code that are operated at same case temperature (±5 C), at same operating conditions, with equal loads (R L = 35, C L = 15 pf), and with an input rise time less than 5 ns. 6. Common-mode transient immunity at output HIGH is the maximum tolerable positive dvcm/dt on the leading edge of the common-mode impulse signal, V CM, to assure that the output remains HIGH. Common-mode transient immunity at output LOW is the maximum tolerable negative dvcm/dt on the trailing edge of the common pulse signal, V CM, to assure that the output remains LOW. FOD8163, FOD8163T Rev

8 Typical Performance Characteristics - INPUT LED CURRENT (ma) V OL - LOGIC LOW OUTPUT VOLTAGE (V) I CCL - LOGIC LOW OUTPUT SUPPLY CURRENT (ma) o C -4 o C 1E = o C V F - FORWARD VOLTAGE (V) Figure 4. Input LED Current vs. Forward Voltage I OL = 13 ma = 6 ma Figure 6. Logic Low Output Voltage vs. = ma = 5. V = 3.3 V = 3.3 V = 5. V Figure 8. Logic Low Output Supply Current vs. HL - THRESHOLD INPUT CURRENT (ma) I OH - LOGIC HIGH OUTPUT CURRENT ( A) I CCH - LOGIC HIGH OUTPUT SUPPLY CURRENT (ma) I OL = 13 ma = 3.3 V = 5. V Figure 5. Threshold Input Current vs. = 5 A V O = 3.3 V / 5. V = 3.3 V = 5. V Figure 7. Logic High Output Current vs = A = 5. V = 3.3 V Figure 9. Logic High Output Supply Current vs. FOD8163, FOD8163T Rev

9 Typical Performance Characteristics (Continued) I CC - OUTPUT SUPPLY CURRENT (ma) (l t PHL - t PLH l) - PULSE WIDTH DISTORTION (ns) (l t PHL - t PLH l) - PULSE WIDTH DISTORTION (ns) = A (for I CCH ) = ma (for I CCL ) = 5 o C OUTPUT SUPPLY VOLTAGE (V) I CCL I CCH Figure. Output Supply Current vs. Output Supply Voltage f = 5 MHz, 5% Duty Cycle = 6 ma, R L = 35 Figure 1. Pulse Width Distortion vs. f = 5 MHz, 5% Duty Cycle = 5 o C, R L = INPUT LED CURRENT (ma) t P - PROPAGATION DELAY (ns) t P - PROPAGATION DELAY (ns) t R, t F - RISE, FALL TIME (ns) f = 5 MHz, 5% Duty Cycle = 6 ma, R L = 35 t t t t Figure 11. Propagation Delay vs. f = 5 MHz, 5% Duty Cycle = 6 ma, R L = 35 t t t t INPUT LED CURRENT (ma) 4 3 Figure 13. Propagation Delay vs. Input LED Current f = 5 MHz, 5% Duty Cycle = 6 ma, R L = 35 t t t t Figure 14. Pulse Width Distortion vs. Input LED Current Figure 15. Rise Time and Fall Time vs. FOD8163, FOD8163T Rev

10 Test Circuit Pulse Gen. 5 MHz t f = tr = 5 ns DC = 5% Input Monitoring Mode Output t f R M t PHL.1 μf Bypass 35 Ω V O Monitoring Node C L Figure 16. Test Circuit for Propagation Delay, Rise Time, and Fall Time SW Input R M V CM 9% % t r t PLH V CM Pulse Gen 5% ( = 6 ma) t r 9% 1.5 V % V OL.1 μf Bypass t f 35 Ω C L 1 kv V V O Monitoring Node V O ( = ma) V OH V V O ( = 6 ma).8 V V OL Figure 17. Test Circuit for Instantaneous Common-Mode Rejection Voltage FOD8163, FOD8163T Rev

11 Reflow Profile Temperature ( C) TP TL Maximum Ramp-up Rate = 3 C/s Maximum Ramp-down Rate = 6 C/s T smax T smin Preheat Area Profile Freature 4 36 Time 5 C to Peak Time (seconds) Figure 18. Reflow Profile Pb-Free Assembly Profile Temperature Minimum (T smin ) 15 C Temperature Maximum (T smax ) C Time (t S ) from (T smin to T smax ) 6 s to s Ramp-up Rate (t L to t P ) 3 C/second maximum Liquidous Temperature (T L ) 17 C Time (t L ) Maintained Above (T L ) 6 s to 15 s Peak Body Package Temperature 6 C + C / 5 C Time (t P ) within 5 C of 6 C 3 s Ramp-Down Rate (T P to T L ) 6 C/s maximum Time 5 C to Peak Temperature 8 minutes maximum ts tl t P FOD8163, FOD8163T Rev. 1.1

12 Ordering Information Part Number Package Packing Method FOD8163 Stretched Body SOP 6-Pin Tube ( units per tube) FOD8163R Stretched Body SOP 6-Pin Tape and Reel (1, units per reel) FOD8163V All packages are lead free per JEDEC: J-STD-B standard. Marking Information Stretched Body SOP 6-Pin, DIN EN/IEC Option Tube ( units per tube) FOD8163RV Stretched Body SOP 6-Pin, DIN EN/IEC Option Tape and Reel (1, units per reel) FOD8163T Stretched Body SOP 6-Pin, Wide Lead Tube ( units per tube) FOD8163TR Stretched Body SOP 6-Pin, Wide Lead Tape and Reel (1, units per reel) FOD8163TV FOD8163TRV Stretched Body SOP 6-Pin, Wide Lead, DIN EN/IEC Option Stretched Body SOP 6-Pin, Wide Lead, DIN EN/IEC Option Definitions 3 V XX YY 1 Fairchild Logo Device Number, e.g P DIN EN/IEC Option (only appears on component 3 ordered with this option) 4 One Digit Year Code, e.g. 5 5 Two Digit Work Week Ranging from 1 to 53 6 Assembly Package Code Tube ( units per tube) Tape and Reel (1, units per reel) 1 6 FOD8163, FOD8163T Rev

13 A (.78) PIN 1 INDICATOR ± ±.3 B RECOMMENDED LAND PATTERN 3.18±.3 (1.59).±..4±. 6X. C A B 6X C. C NOTES: UNLESS OTHERWISE SPECIFIED A) NO STANDARD APPLIES TO THIS PACKAGE B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS DO NOT INCLUDE BURRS OR MOLD FLASH, AND TIE BAR EXTRUSION. D) DIMENSIONING AND TOLERANCING PER ASME Y14.5M-9. E) DRAWING FILE NAME: MKT-M6BREV1

14 1.7 (.54) 3 1 (.78) A PIN 1 INDICATOR 6.81± ±.3 B RECOMMENDED LAND PATTERN R ±.3 (1.59) R.15.4~.34.±..4±. 6X. C A B 6X C. C.75± ±.3 ~8 NOTES: UNLESS OTHERWISE SPECIFIED A) NO STANDARD APPLIES TO THIS PACKAGE B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS DO NOT INCLUDE BURRS OR MOLD FLASH, AND TIE BAR EXTRUSION. D) DIMENSIONING AND TOLERANCING PER ASME Y14.5M-9. E) DRAWING FILE NAME: MKT-M6CREV1

15 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor s product/patent coverage may be accessed at Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. Typical parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customer s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 1951 E. 3nd Pkwy, Aurora, Colorado 811 USA Phone: or Toll Free USA/Canada Fax: or Toll Free USA/Canada orderlit@onsemi.com Semiconductor Components Industries, LLC N. American Technical Support: Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: Japan Customer Focus Center Phone: ON Semiconductor Website: Order Literature: For additional information, please contact your local Sales Representative