Surface Mount Transient Voltage Suppressors (TVS)
|
|
- Jonah Norton
- 5 years ago
- Views:
Transcription
1 Description The 1.5SMC series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Uni-directional For surface mounted applications in order to optimize board space Low leakage Uni and Bidirectional unit Glass passivated junction Low inductance Excellent clamping capability 1500W Peak power capability at 10 0µs waveform Repetition rate (duty cycle):0.01% Fast response time: typically less than 1.0ps from 0 Volts to V BR min Typical I R less than 5μA above 12V. High Temperature soldering: 260 C/40 seconds at terminals Typical maximum temperature coefficient ΔV BR = 0.1% V BR@25 C ΔT Plastic package has Underwriters Laboratory Flammability 94V-0 Matte tin lead free Plated Halogen free and RoHS compliant Typical failure mode is short from over-specified voltage or current Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c IEC ESD 15kV(Air), 8kV (Contact) ESD protection of data lines in accordance with IEC (IEC801-2) EFT protection of data lines in accordance with IEC (IEC801-4) Functional Diagram Cathode Anode Uni-direction Agency Approvals AGENCY AGENCY FILE NUMBER E Applications TVS devices are ideal for the protection of I/O interfaces, C bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Maximum Ratings (T A =25 unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation with a 10/0µs waveform (Fig.1)(Note 1), (Note 2) P PPM 1500 Watts Peak Pulse Current with a 10/0µs waveform.(note1,fig.3) I PP See Next Table Amps Power Dissipation on Infinite Heat Sink at T L=75 C P M(AV) 6.5 Watt Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) I FSM 200 Amps Maximum Instantaneous Forward Voltage at 25A for Unidirectional Only (Note 4) V F 3.5/5.0 Voltage Operating junction and Storage Temperature Range. T J, T STG -55 to +150 C Notes: 1. Non-repetitive current pulse, per Fig. 3 and derated above T A = 25 C per Fig Mounted on 5.0mm x 5.0mm (0.03mm thick) Copper Pads to each terminal ms single half sine-wave, or equivalent square wave, Duty cycle = 4 pulses per minutes maximum. 4. V F < 3.5V for V BR < 200V and V F< 6.5V for V BR > 201V. Revision September 25, / 2013
2 Electrical Characteristics (T A =25 unless otherwise noted) Part Number Marking Uni Bi Uni Bi Reverse Breakdown Stand-Off Voltage V BR (V) V RWM (V) MIN MAX Test Current (ma) Maximum Clamping PP (V) Maximum Peak Pulse Current I PP (A) Maximum Reverse Leakage I RWM (μa) 1.5SMC6.8A 1.5SMC6.8CA 6V8A 6V8C SMC7.5A 1.5SMC7.5CA 7V5A 7V5C SMC8.2A 1.5SMC8.2CA 8V2A 8V2C SMC9.1A 1.5SMC9.1CA 9V1A 9V1C SMC10A 1.5SMC10CA 10A 10C SMC11A 1.5SMC11CA 11A 11C SMC12A 1.5SMC12CA 12A 12C SMC13A 1.5SMC13CA 13A 13C SMC15A 1.5SMC15CA 15A 15C SMC16A 1.5SMC16CA 16A 16C SMC18A 1.5SMC18CA 18A 18C SMC20A 1.5SMC20CA 20A 20C SMC22A 1.5SMC22CA 22A 22C SMC24A 1.5SMC24CA 24A 24C SMC27A 1.5SMC27CA 27A 27C SMC30A 1.5SMC30CA 30A 30C SMC33A 1.5SMC33CA 33A 33C SMC36A 1.5SMC36CA 36A 36C SMC39A 1.5SMC39CA 39A 39C SMC43A 1.5SMC43CA 43A 43C SMC47A 1.5SMC47CA 47A 47C SMC51A 1.5SMC51CA 51A 51C SMC56A 1.5SMC56CA 56A 56C SMC62A 1.5SMC62CA 62A 62C SMC68A 1.5SMC68CA 68A 68C SMC75A 1.5SMC75CA 75A 75C SMC82A 1.5SMC82CA 82A 82C SMC91A 1.5SMC91CA 91A 91C SMCA 1.5SMCCA A C SMC110A 1.5SMC110CA 110A 110C SMC120A 1.5SMC120CA 120A 120C SMC130A 1.5SMC130CA 130A 130C SMC150A 1.5SMC150CA 150A 150C SMC160A 1.5SMC160CA 160A 160C SMC170A 1.5SMC170CA 170A 170C SMC180A 1.5SMC180CA 180A 180C SMC200A 1.5SMC200CA 200A 200C SMC220A 1.5SMC220CA 220A 220C SMC250A 1.5SMC250CA 250A 250C SMC300A 1.5SMC300CA 300A 300C SMC350A 1.5SMC350CA 350A 350C SMC380A 1.5SMC380CA 380A 380C SMC400A 1.5SMC400CA 400A 400C SMC440A 1.5SMC440CA 440A 440C SMC500A 1.5SMC500CA 500A 500C SMC520A 1.5SMC520CA 520A 520C SMC550A 1.5SMC550CA 550A 550C SMC600A 1.5SMC600CA 600A 600C Note: 1. Suffix 'A ' denotes 5% tolerance device. Without 'A' denotes 10% tolerance device 2. Add suffix 'C 'or ' CA ' after part number to specify devices 3. For Bi-Directional devices having V R of 10 volts and under, the I R limit is double Revision September 25, / 2013
3 Ratings and Characteristic Curves (T A =25 C unless otherwise noted) Figure 1 - Peak Pulse Power Rating Curve Figure 2 - Pulse Derating Curve PPPM - Peak Pulse Power (kw) t d - Pulse Width (μs) Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % T A-Ambient temperature( C) Figure 3 - Pulse Waveform Figure 4 - Typical Junction Capacitance IPPM - Peak Pulse Current, % IRSM t c t r=10µsec Peak Value IPPM Half Value I PPM (I PPM/2) TJ=25 C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 10/0µsec. Waveform as defined by R.E.A t - Time (ms) CJ Junction Capacitance (pf) bins bins 10 Tj=25 RWM f=1.0mhz Vsig=50mVp-p V BR-Reverse Breakdown Voltage (V) Figure 5 - Steady State Power Derating Curve Figure 6 - Maximum Non-Repetitive Surge Current PM(AV), Steady State Power Dissipation (W) T L - Lead Temperature( C) IFSM-Peak Forward Surge Current (A) TJ=TJ max. 8.3 ms Single Half Sine-Wave Number of Cycles at 60Hz Revision September 25, / 2013
4 I-urve Characteristics Uni-directional I I I F I PP V BRV RW R V F V V BRV RW R I R I R V RW V BR R V I PP I PP Physical Specifications Environmental Specifications Weight Case Polarity Terminal ounce, 0.21 gram JEDEC DO-214AB Molded Plastic over glass passivated junction Temperature Cycle Pressure Cooker High Temp. Storage JESD22-A104 JESD22-A102 JESD22-A103 Color band denotes cathode except Bipolar HTRB JESD22-A108 Matte Tin-plated leads, Solderable per JESD22-B102D Thermal Shock JESD22-A106 Soldering Parameters Reflow Condition Lead free assembly T P Ramp-up Critical Zone TL to TP -Temperature Min (T s(min)) 150 C Temperature T L T S(max) T S(min) Preheat Ramp-down Pre Heat -Temperature Max (T s(max)) 200 C - Time (min to max) (T s) Seconds Average ramp up rate ( Liquidus Temp T L) to peak T S(max) to TL - Ramp-up Rate 3 C/second max 3 C/second max 25 Time to peak temperature (t 25 to peak) Time Reflow - Temperature (T L) (Liquidus) 217 C - Time (min to max) (T L) Seconds Peak Temperature (T P) Time within 5 C of actual peak Temperature (t p) Ramp-down Rate Time 25 C to peak Temperature (T P) /-5 C Seconds 6 C/second max 8 minutes Max Do not exceed 280 C Revision September 25, / 2013
5 Dimensions DO-214AB (SMC) Cathode Band Dimensions Inches Millimeters Min Max Min Max A B C D E F G H I J K L Part Numbering Part Marking 1. 5 S M C C A 5% V BR VOLTAGE TOLERANCE BI-DIRECTIONAL V R VOLTAGE SERIES Revision September 25, / 2013
6 Packaging Part Number Component Package Quantity Packaging Option Packaging Specification 1.5SMCXXXXX DO-214AB 500 Tape & Reel -16mm/7 tape EIA STD RS-481 Tape and Reel Specifications Revision September 25, / 2013
P6SMB Series. TVS Diodes Surface Mount 600W > P6SMB series. Description. Uni-directional
RoHS Pb e3 Uni-directional Description Bi-directional The P6SMB series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient
More informationP4SMA-E Series. TVS Diodes Surface Mount 400W > P4SMA-E series Series. Description. Uni-directional
P4SMA-E Series RoHS Pb e3 Description The P4SMA-E series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events.
More informationP6SMB-E Series. TVS Diodes Surface Mount 600W > P6SMB-E series Series. Description. Uni-directional
P6SMB-E Series RoHS Pb e3 Description The P6SMB-E series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events.
More informationTransient Voltage Suppression Diodes Axial Leaded 600W > P6KE series
Axial Leaded 6W > P6KE series RoHS Pb Description The is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events.
More informationTransient Voltage Suppression Diodes. Surface Mount 400W > P4SMA series. Features. less than 1μA when V BR. Applications. Additional Infomarion
P4SMA Series RoHS Pb e3 Uni-directional Bi-directional Description The P4SMA series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other
More informationTransient Voltage Suppression Diodes Axial Leaded 5000W > TP5KP series. Features. Bi-directional 5000 W 8.0 W 400 A 3.5 V. -55 to 150 C.
TP5KP Series RoHS Pb e3 Description The TP5KP Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events.
More informationTransient Voltage Suppression Diodes Axial Leaded 1500W > TP1.5KE series. Features 1500 W 6.5 W 200 A 3.5 V. -55 to 150 C. -55 to 175 C 15 C/W 75 C/W
TP.5KE Series RoHS Pb e3 Description The TP.5KE Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events.
More informationDATA SHEET TRANSIENT VOLTAGE SUPPRESSORS AC/DC POWER SUPPLY 1.0SMB series
Product specification November 5, 28 V. DATA SHEET TRANSIENT VOLTAGE SUPPRESSORS AC/DC POWER SUPPLY.SMB series RoHS compliant & Halogen free Transient Suppressors.SMB 2 Transient Suppressors (TVS) Data
More informationP4KE Series RoHS Pb e3
P4KE Series RoHS Pb e3 Description Bi-directional Uni-directional The P4KE Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other
More informationTransient Voltage Suppression Diodes Surface Mount 600W > TPSMA6L Series 3 W 60 A 3.5V V. -65 to 150 C 35 C/W 200 C/W. Anode
Surface Mount 6W > RoHS Description Uni-directional The is designed specifically to protect sensitive electronic equipment from voltage transients induced by load dump and other transient voltage events,
More informationP6SMB Series. Transient Voltage Suppression Diodes. Surface Mount 600W > P6SMB series. Description
P6SMB Series RoHS Pb e3 Description Uni-directional The P6SMB series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient
More information5KP Series. Transient Voltage Suppression Diodes. Axial Leaded 5 kw > 5KP series. Description
5KP Series RoHS Pb e3 Description Uni-directional The 5KP Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage
More information15KPA Series. Transient Voltage Suppression Diodes. Axial Leaded 15000W > 15KPA series. Descriptions. Uni-directional
5KPA Series RoHS Pb e3 Descriptions Uni-directional The 5KPA Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage
More information3KP Series. Transient Voltage Suppression Diodes. Axial Leaded 3000W > 3KP series. Description
3KP Series RoHS Pb e3 3/3/27 LFPCN2244 5KP Series Description Uni-directional The 3KP Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning
More informationLCE Series. Transient Voltage Suppression Diodes. Axial Leaded 1500W > LCE series. Description. Uni-directional
Transient Suppression Diodes LCE Series RoHS Pb e3 Uni-directional Description The LCE Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning
More informationTransient Voltage Suppression Diodes Axial Leaded 500W > SA series
Axial Leaded 5W > SA series RoHS b Description The is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Agency
More information5KP-HRA Series. Transient Voltage Suppression Diodes Axial Leaded 5000W > 5KP-HRA series. Description. Uni-directional
5KP-HRA Series RoHS Pb e3 AGENCY Uni-directional Agency Approvals AGENCY FILE NUMBER E28662/E2353 Parameter Symbol Value Unit Peak Pulse Power Dissipation by /μs Test Waveform (Fig.2) (Note ) P PPM 5 W
More information30KPA-HRA Series. Transient Voltage Suppression Diodes Axial Leaded 30000W > 30KPA-HRA series. Descriptios. Uni-directional
3KPA-HRA Series RoHS Pb e3 AGENCY Uni-directional Agency Approvals Parameter Symbol Value Unit Peak Pulse Power Dissipation by /μs Test Waveform (Fig.2) (Note ) P PPM 3 W Steady State Power Dissipation
More informationTP6KE Series. TVS Diodes Axial Leaded 600W > TP6KE series
TP6KE Series RoHS Pb e3 AGENCY Agency Approvals AGENCY FILE NUMBER E2353 Parameter Symbol Value Unit Peak Pulse Power Dissipation by /μs Test Waveform (Fig.2) (Note ) 6 W Steady State Power Dissipation
More informationSMA6L Series. Transient Voltage Suppression Diodes. Surface Mount 600W > SMA6L series
SMA6L Series RoHS Pb e3 Uni-directional Description The SMA6L series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient
More informationSMF Series. Transient Voltage Suppression Diodes. Surface Mount 200W > SMF Series. Description. Uni-directional
SMF Series RoHS Pb e3 Uni-directional Description The SMF series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage
More informationSMF4L Series. TVS Diodes Surface Mount 400W > SMF4L Series. Description. Uni-directional
SMF4L Series RoHS Pb e3 Uni-directional Description The SMF4L series of SOD-123FL small and flat lead lowprofile plastic package is designed specifically to protect sensitive electronic equipment from
More informationTransient Voltage Suppressors (TVS) Data Sheet
Transient Suppressors (TVS) Data Sheet Features For surface mounted applications in order to optimize board space Low profile package Built-in strain relief Glass passivated junction Low inductance Excellent
More information5.0SMDJxxS Series, Single Chip Design
5.SMDJxxS Series, Single Chip Design RoHS Pb e3 Description The 5.SMDJxxS series, single chip design is designed specifically to protect sensitive electronic equipment from voltage transients induced by
More informationSLD Series. TVS Diodes. Axial Leaded 2200W > SLD series. Description
SLD Series RoHS Pb e3 Description AGENCY Agency Approvals AGENCY FILE NUMBER E2353 Ratings and Thermal Characteristics (T A =25 O C unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power
More informationICTE5.0 THRU ICTE15C SERIES
ICTE5.0 THRU ICTE15C SERIES TRANSZORB TRANSIENT VOLTAGE SUPPRESSOR Stand-off Voltage - 5.0 to 15 Volts Peak Pulse Power - Watts Case Style 1.5KE 1.00 (25.4) MIN. 0.205 (5.207) 0.190 (4.826) DIA. 0.375
More informationSurface Mount Transient Voltage Suppressors (TVS)
Description The SMF series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Uni-directional Compatible
More informationSLD8S Series RoHS Pb e3
SLD8S Series RoHS Pb e3 Description The SLD8S Series TVS Diode is housed in a SMTO-263 package with lead modifications. It is designed to protect sensitive electronics against lightning and inductive load
More informationTransient Voltage Suppression Diodes Surface Mount 600W > SMBJ-HR series. Bi-directional. Features 5.0 W 100 A 3.5V/5.0 V. -55 to 150 C 20 C/W
SMBJ-HR Series RoHS Uni-directional Description TVS Diode Arrays (SPA Family of Products Bi-directional The SMBJ-HR High Reliability series is designed specifically to protect sensitive electronic equipment
More informationTransient Voltage Suppressors (TVS) Data Sheet
Transient Suppressors (TVS) Data Sheet Features Glass passivated junction Low zener impedance Excellent clamping capability 400W peak pulse power capability at 10/1000μs waveform, repetition rate (duty
More information1KSMB Series. Transient Voltage Suppression Diodes. Surface Mount 1000W > 1KSMB series. Uni-directional. Description
Surface Mount W > KSMB series KSMB Series RoHS Pb e3 Uni-directional Description Bi-directional The KSMB series is designed specifically to protect sensitive electronic equipment from voltage transients
More informationSurface Mount Transient Voltage Suppressors (TVS)
Description The SMAJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Uni-directional
More informationSURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 400 WATT PEAK POWER 1.0 WATTS STEADY STATE SYMBOL IPPM P M(AV) I FSM T J, T STG
SURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 4 WATT PEAK POWER 1. WATTS STEADY STATE TVS P4FMAJ SERIES FEATURES * Plastic package has underwriters laboratory * Glass passivated chip construction * 4
More informationTransient Voltage Suppression Diodes Surface Mount 600W > SMBJ series. SMBJ Series. SMBJ Series
Surface Mount 6W > SMBJ series RoHS Agency Approvals AGENCY AGENCY FILE NUMBER E28662/E2353 Maximum Ratings and Thermal Characteristics ( =25 O C unless otherwise noted Parameter Symbol Value Unit Peak
More informationTransient Voltage Suppression Diodes Surface Mount 400W > SMAJ series. SMAJ Series. SMAJ Series
Surface Mount 4W > SMAJ series RoHS Agency Approvals AGENCY AGENCY FILE NUMBER E2353 Ratings and Thermal Characteristics ( =25 O C unless otherwise noted Parameter Symbol Value Unit Peak Pulse Power Dissipation
More informationP4KE SERIES Taiwan Semiconductor
400W, 6.8V - 440V Transient Voltage Suppressor FEATURES - Excellent clamping capability - Low dynamic impedance - 400W surge capability at 10 / 1000 μs waveform - Fast response time: Typically less than
More informationP6KE SERIES Taiwan Semiconductor
600W, 6.8V - 440V Transient Voltage Suppressor FEATURES - Excellent clamping capability - Low dynamic impedance - 600W surge capability at 10 / 0 μs waveform - Fast response time: Typically less than 1.0ps
More informationTransient Voltage Suppression Diodes Surface Mount 600W > SMBJ series
Surface Mount 6W > SMBJ series RoHS Pb Description The SMBJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage
More information15,000 Watt Transient Voltage Suppressor (TVS) Protection Device
Compliant 15,000 Watt Transient Voltage Suppressor (TVS) Protection Device DESCRIPTION This device clamps dangerous high-voltage short-term transients such as those produced by the secondary effects of
More information5KP Series 5000 Watt Axial Leaded Transient Voltage Suppressor
5KP Series 5000 Watt Axial Leaded Transient Voltage Suppressor Description The 5KP Series are designed specifically to protect sensitive Uni-directional electronics equipment from voltage transients induced
More informationTPSMD Series. TVS Diodes Surface Mount 3000W > TPSMD series. Description
TPSMD Series RoHS Pb e3 Description Bi-directional The TPSMD series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage
More informationSA SERIES Taiwan Semiconductor
500W, 5V - 170V Transient Suppressor FEATURES - Excellent clamping capability - Low dynamic impedance - 500W surge capability at 10 / 0 μs waveform - Fast response time: Typically less than 1.0ps from
More informationSurface Mount Transient Voltage Suppressors (TVS)
Description The 5.0SMDJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Uni-directional
More informationBZW04 SERIES Taiwan Semiconductor
W, 5.8V - 376V Transient Voltage Suppressor BZW4 SERIES FEATURES - Excellent clamping capability - Low impedance surge resistance - W surge capability at / μs waveform - Very fast response time - Typical
More informationSurface Mount TRANSZORB Transient Voltage Suppressors
Surface Mount TRANSZORB Transient Voltage Suppressors PRIMARY CHARACTERISTICS V WM (uni-directional) 5.8 V to 459 V V WM (bi-directional) 5.8 V to 185 V V BR (uni-directional) 6.8 V to 540 V V BR (bi-directional)
More informationSURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 400 WATT PEAK POWER 1.0 WATTS STEADY STATE SYMBOL IPPM P M(AV) I FSM. I 2 t 6.64 A 2 /Sec T J, T STG
SURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 4 WATT PEAK POWER 1. WATTS STEADY STATE TVS P4FMAJ SERIES FEATURES * Plastic package has underwriters laboratory * Glass passivated chip construction * 4
More informationDEVICES FOR BIPOLAR APPLICATIONS
SEMICONDUCTOR TECHNICAL SPECIFICATION GPP TRANSIENT VOLTAGE SUPPRESSOR 15 WATT PEAK POWER 5. WATTS STEADY STATE TVS 1.5KE SERIES FEATURES * Plastic package has underwriters laboratory certificate * Glass
More informationSMCJ5.0CA Thru SMCJ170CA
Transient Suppressors TVS Diodes - 1500W > SMCJ Series SMCJ5.0CA Thru SMCJ170CA Description The SMCJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced
More information6600W Transient Voltage Suppressor (TVS)
Description SM8S Series TVS diodes can be used in sensitive electronics protection against voltage transients induced by inductive load switching and lighting, especially for automotive load dump protection
More information30KP SERIES. Features. Mechanical Data. Maximum Ratings and Electrical A =25 C unless otherwise specified
3KP SERIES 3W TRANSIENT VOLTAGE SUPPRESSOR Pb Features Glass Passivated Die Construction 3W Peak Pulse Power Dissipation 8V 88V Standoff Voltage A B A Uni- and Versions Available Excellent Clamping Voltage
More information500W Glass Passivated Junction Transient Voltage Suppressor. JEDEC DO-15 molded plastic body over passivated junction
Glass Passivated Junction Transient Voltage Suppressor SA5.0A -SA180CA 500W Glass Passivated Junction Transient Voltage Suppressor Features Stand-off voltage from 5.0 to 180 volts Glass passivated junction
More informationS M A J x x x C A. Reverse Stand-Off Voltage
Description The SMAJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Fast response time
More information30KP Series 30000W AXIAL LEAD TRANSIENT VOLTAGE SUPPRESSOR R-6 PACKAGE WILLAS ELECTRONIC CORP. R-6 (Cathode band Only Uui-polarity product)
3W AXIAL LEAD TRANSIENT VOLTAGE SUPPRESSOR 3KP Series 1.(25.4)MIN..36(9.14).338(8.6) 1.(25.4)MIN. R-6 (Cathode band Only Uui-polarity product).52(1.32).47(1.2) Dimensions in inches and (millimeters) DIA..36(9.14).338(8.6)
More informationTransient Voltage Suppression Diodes: P6SMB Series SMD Type 600 W
Features 1. For surface mounted applications 2. RoHS compliant and halogen-free 3. Reliable low cost construction utilizing molded plastic technique 4. Glass passivated chip junction 5. Both bi-directional
More informationSurface Mount Transient Voltage Suppressors
TVS diodes can be used in a wide range of applications which like consumer electronic products, automotive industries, munitions, telecommunications, aerospace industries, and intelligent control systems.
More informationGPP TRANSIENT VOLTAGE SUPPRESSOR 3000 WATT PEAK POWER 7.5 WATTS STEADY STATE SYMBOL. W Steady State Power Dissipation at T L = 75 O C P M(AV) I FSM
GPP TRANSIENT VOLTAGE SUPPRESSOR 3 WATT PEAK POWER 7.5 WATTS STEADY STATE TVS 3KPSMC SERIES FEATURES * Plastic package has underwriters laboratory * Glass passivated chip construction *3 watt surage capability
More informationTransient Voltage Suppressors. SMBJ Series. Circuit Protection System
Transient Suppressors SMBJ Series Features UNI Very fast response time Halogen free and RoHS compliant Low incremental surge resistance Optimized for LAN protection applications Matte tin lead free Plated
More informationP6SMB Transient Voltage Suppressor Diode Series
P6SMB Transient Voltage Suppressor Diode Series General Information The P6SMB series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping
More informationFAIRCHILD TVS Is Now Part of
FAIRCHILD TVS Is Now Part of To learn more about Taiwan Semiconductor, please visit our website at www.taiwansemi.com Please note: The acquisition of this portfolio aligns with our strategy to expand in
More informationTPSMC-VR Series. TVS Diodes Surface Mount 1500W > TPSMC-VR series Series. Description. Uni-directional. Bi-directional
TPSMC-VR Series Description RoHS Pb e3 The TPSMC-VR series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events.
More informationP6KE-G Series. 600W Transient Voltage Suppressor. Stand-off Voltage: 6.8 ~ 600V Power Dissipation: 600 Watts RoHS Device. Features.
P6KE-G Series Stand-off Voltage: 6.8 ~ 6V Power Dissipation: 6 Watts RoHS Device Features -Plastic package has underwriters laboratory flammability classification 94V- -6W, surge capability at ms. -Excellent
More informationM C C. SMCJ1.5KE6.8(C)A THRU SMCJ1.5KE550(C)A. Features. Transient Voltage Suppressor 6.8 to 550 Volts 1500 Watt.
omponents 20736 Marilla Street Chatsworth!"# $%!"# SMCJ1.5KE6.8(C)A THRU SMCJ1.5KE550(C)A Features For surface mount applicationsin in order tooptimize board space Lead Free Finish/Rohs Compliant (Note1)
More informationSMBJ Series. Transient Voltage Suppression Diodes. Surface Mount 600W > SMBJ series. Description. Uni-directional
SMBJ Series RoHS Pb e3 Uni-directional Description Bi-directional The SMBJ is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient
More information15,000 Watt Transient Voltage Suppressor (TVS) Protection Device
M1KP22A M1KP280CA(e3) Available 1,000 Watt Transient Voltage Suppressor (TVS) Protection Device DESCRIPTION This Transient Voltage Suppressor series of M1KP22A M1KP280CA offers an extended voltage range
More informationTransient Voltage Suppressors (TVS) Data Sheet
Transient Suppressors (TVS) Data Sheet Features For surface mounted applications in order to optimize board space Low profile package Built-in strain relief Glass passivated junction Low inductance Excellent
More informationFAIRCHILD TVS Is Now Part of
FAIRCHILD TVS Is Now Part of To learn more about Taiwan Semiconductor, please visit our website at www.taiwansemi.com Please note: The acquisition of this portfolio aligns with our strategy to expand in
More informationTransient Voltage Suppressors. SMAJ Series. Circuit Protection System
Transient Suppressors SMAJ Series Features UNI Fast response time Low incremental surge resistance Matte tin lead free Plated Halogen ree and RoHS compliant Typical IR less than 1µA above 10V Compatible
More informationSMBJ. Transient Voltage Suppression Diodes. Surface Mount 600W > SMBJ series. Description. Uni-directional
SMBJ RoHS Pb e3 Uni-directional Description Bi-directional The SMBJ is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage
More informationDistributed by: www.jameco.com 1-8-831-4242 The content and copyrights of the attached material are the property of its owner. P6KE6V8(C)A - P6KE4(C)A 6W TRANSIENT VOLTAGE SUPPRESSOR Features 6W Peak Pulse
More informationBZW06 SERIES Taiwan Semiconductor
600W, 3V - 376V Transient Voltage Suppressor FEATURES - Excellent clamping capability - Low dynamic impedance - 600W surge capability at / 0 μs waveform - Fast response time: Typically less than.0ps from
More informationSMBJ5.0 THRU SMBJ440CA
SMBJ5.0 THRU SMBJ440CA SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR Stand-off : 5.0-440 Volts Peak pulse power: 600 Watts 0.087 (2.20) 0.071 (1.80) 0.096(2.44) 0.084(2.13) SMB/DO-214AA 0.180(4.57) 0.160(4.06)
More informationSales: Technical: Fax:
DATA SHEET Order code Manufacturer code Description 47-4344 n/a SMCJ33CA TVS DIODE BIDIRECTIONAL SMC (RC 47-4346 n/a SMCJ40CA TVS DIODE BIDIRECTIONAL SMC (RC 47-4290 n/a SMCJ5.0A TVS DIODE UNIDIRECTIONAL
More informationTransient Voltage Suppressors (TVS) Data Sheet
Transient Suppressors (TVS) Data Sheet Features For surface mounted applications in order to optimize board space Low profile package Built-in strain relief Glass passivated junction Low inductance Excellent
More informationSymbol Description Value Unit Conditions. Minimum 600
600W Surface Mount Transient Voltage Suppressor Features SMB Breakdown voltage from 6.8 to 250 volts Low inductance, excellent clamping capability Repetition rate(duty cycle): 0.01% Fast response time:
More informationDEVICES FOR BIPOLAR APPLICATIONS. For Bidirectional use C or CA suffix for types 3KP5.0 thru 3KP110 Electrical characteristics apply in both direction
TVS 3KP SERIES GPP TRANSIENT VOLTAGE SUPPRESSOR 3 WATT PEAK POWER 8. WATTS STEADY STATE FEATURES * Plastic package has underwriters laboratory * Glass passivated chip construction * 3 watt surage capability
More informationAutomotive Electrical Overvoltage Transient Suppressors Leaded - > ATH series
Automotive Electrical Overvoltage Transient Suppressors Leaded - > ATH series Description Overvoltage transient suppressors are designed for applications requiring a low voltage rectifier with reverse
More informationSURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 600 WATT PEAK POWER 5.0 WATTS STEADY STATE DEVICES FOR BIPOLAR APPLICATIONS
SURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 600 WATT PEAK POWER 5.0 WATTS STEADY STATE TVS SMBJ SERIES FEATURES * Peak pulse power:600 W (/00 μs),4 kw (8/20 μs) * Plastic package has underwriters laboratory
More information1500 Watt Low Clamping Factor Transient Voltage Suppressor
1N6358 1N637 or Available 1500 Watt Low Clamping Factor Transient Voltage Suppressor DESCRIPTION This Transient Voltage Suppressor (TVS) series for 1N6358 through 1N637 are JEDEC registered selections
More informationSURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 1500 WATT PEAK POWER 6.5 WATTS STEADY STATE
SURFACE MOUNT GPP TRANSIENT VOLTAGE SUPPRESSOR 15 WATT PEAK POWER 6.5 WATTS STEADY STATE TVS TFMCJ SERIES FEATURES * Plastic package has underwriters laboratory * Glass passivated chip construction * 15
More information5KP8.5A thru 5KP188A. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. FEATURES TYPICAL APPLICATIONS
TRANSZORB Transient Voltage Suppressors P6 PRIMARY CHARACTERISTICS V WM 8.5 V to 188 V V BR 9.4 V to 231 V P PPM 5 W P D 8. W I FSM 5 A T J max. 175 C Polarity Uni-directional Package P6 FEATURES P6 glass
More information200W, 5V - 100V Surface Mount Transient Voltage Suppressor
200W, 5V - 100V Surface Mount Transient Voltage Suppressor FEATURES Photo Glass passivated junction Low power loss, high efficiency Ideal for automated placement Excellent clamping capability Typical I
More informationICTE5 thru ICTE18C, 1N6373 thru 1N6386. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor.
TRANSZORB Transient Voltage Suppressors Case Style 1.5KE PRIMARY CHARACTERISTICS V WM 5. V to 18 V V BR (uni-directional) 6. V to 21.2 V V BR (bi-directional) 9.2 V to 21.2 V P PPM 1 W P D 6.5 W I FSM
More informationAQ4022 Series 1.3pF, 15A Discrete TVS Diode
Lightning Surge Protection- SP4022 AQ4022 Series AQ4022 Series 1.3pF, 15A Discrete TVS Diode RoHS Pb GREEN Description The AQ4022 series integrates low capacitance steering diodes with one or two avalanche
More information20KW Transient Voltage Suppressor 20KPA20A 20KPA300CA. 20KW Transient Voltage Suppressor. Features. Mechanical Data
Features Glass passivated junction 20KW peak pulse power capability at 10/1000μs waveform repetition rate (duty cycles): 0.01% Fast response time: typically less than 1.0ps from 0v to VBR min. Excellent
More informationPAM31DOAB Series 1500 WATT TVS COMPONENT APPLICATIONS DO-214AB PACKAGE MECHANICAL CHARACTERISTICS FEATURES PIN CONFIGURATIONS.
15 WATT TVS COMPONENT APPLICATIONS Automotive DO-214AB PACKAGE FEATURES AEC-Q11 Qualified UL File Recognition #E28219 Compatible with IEC 6-4-2 (ESD): Level 4 - Air 15kV, Contact 8kV Compatible with IEC
More informationP4KE6.8A thru P4KE540A. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. FEATURES PRIMARY CHARACTERISTICS
TRANSZORB Transient Voltage Suppressors PRIMARY CHARACTERISTICS V WM 5.8 V to 459 V V BR uni-directional 6.8 V to 54 V V BR bi-directional 6.8 V to 44 V P PPM 4 W P D 1.5 W I FSM (uni-directional only)
More informationSA5.0A thru SA170CA. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. FEATURES PRIMARY CHARACTERISTICS
TRANSZORB Transient Voltage Suppressors DO-204AC (DO-15) PRIMARY CHARACTERISTICS V WM 5.0 V to 170 V V BR (uni-directional) 6.4 V to 209 V V BR (bi-directional) 6.4 V to 209 V P PPM 500 W P D 3.0 W I FSM
More information200W, 5V - 100V Surface Mount Transient Voltage Suppressor
200W, 5V - 100V Surface Mount Transient Voltage Suppressor FEATURES Photo Glass passivated junction Low power loss, high efficiency Ideal for automated placement Excellent clamping capability Typical I
More information1.5SMCxxAT3G. TVS Diodes. Surface Mount > 1500W > 1.5SMCxxAT3G. Cathode. Anode. Uni-directional. Description
1.5SMCxxAT3G Pb Description The 1.5SMCxxAT3G series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge capability,
More informationAQxxC-01FTG Series. TVS Diode Array (SPA Diodes) General Purpose ESD Protection - AQxxC-01FTG SD-C Series Series. RoHS Pb GREEN.
General Purpose ESD Protection - AQxxC-1FTG SD-C Series Series AQxxC-1FTG Series RoHS Pb GREEN Description The bidirectional AQxxC series is designed to replace multilayer varistors (MLVs) in electronic
More informationSP4021 Series 2.5pF, 25A Discrete TVS Diode
SP40 Series.5pF, 5A Discrete TVS Diode RoHS Pb GREEN Description The SP40 components integrate low capacitance steering diodes with one or two avalanche breakdown diodes for unidirectional or bidirectional
More informationSD Series 450W Discrete Unidirectional TVS Diode
General Purpose ESD Protection - 5W Discrete Unidirectional TVS Diode RoHS Pb GREEN Description The SD series is designed to replace multilayer varistors (MLVs) in electronic equipment for low speed and
More informationPAM28DOAC Series 400 WATT TVS COMPONENT APPLICATIONS DO-214AC PACKAGE MECHANICAL CHARACTERISTICS FEATURES PIN CONFIGURATIONS. Automotive Applications
4 WATT TVS COMPONENT APPLICATIONS Automotive Applications DO-214AC PACKAGE FEATURES AEC-Q11 Qualified ISO 7637-2 Pulse 1, 2a, 2b, 3a, 3b Compliant UL File Recognition #E28219 IEC 6-4-2 (ESD): Level 4 -
More informationComchip 3KP-G Transient Voltage Suppressor Datasheet
Comchip 3KP-G Transient Suppressor Datasheet http://www.manuallib.com/comchip/3kp-g-transient-voltage-suppressor-datasheet.html Features -Glass passivated chip. -Low leakage. -Uni and Bidirection unit.
More informationRev. 02
PRIMARY CHARACTERISTICS SMB(DO-214AA) PACKAGE P PP V BR I PP V C 600W 6.8V~600V 57.14A~0.72A 10.5V~828V Body Marking :Please See Page 3 EX : SM 12A EX : SM 12CA T J,Max 150 12 A 12 C UNI- POLAR BI-POLAR
More informationSurface Mount Transient Voltage Suppressor Stand-Off Voltage to 180 Volts 200 Watt Peak Pulse Power
Features Surface Mount Transient Suppressor Stand-Off - 5.0 to 80 olts 0 Watt Peak Pulse Power For surface mounted applications in order to optimize board space Low profile package Built-in strain relief
More informationSP4020 Series 2.5pF, 30A Discrete TVS Diode
SP400 Series.5pF, 30A Discrete TVS Diode RoHS Pb GREEN Description The SP400 components integrate low capacitance steering diodes with one or two avalanche breakdown diodes for unidirectional or bidirectional
More informationSM712 Series 600W Asymmetrical TVS Diode Array
SM712 Series 6W Asymmetrical TVS Diode Array RoHS Pb GREEN Description The SM712 TVS Diode Array is designed to protect RS-485 applications with asymmetrical working voltages (-7V to 12V from damage due
More information400W, 5V - 188V Surface Mount Transient Voltage Suppressor
400W, 5V - 188V Surface Mount Transient Voltage Suppressor FEATURES Low profile package Ideal for automated placement Glass passivated junction Built-in strain relief Excellent clamping capability Fast
More informationTransient Voltage Suppressors (TVS) Data Sheet
Transient Suppressors (TVS) Data Sheet Features For surface mounted applications in order to optimize board space Low profile package Glass passivated junction Low inductance Excellent clamping capability
More information