P4KE6.8A thru P4KE540A. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. FEATURES PRIMARY CHARACTERISTICS
|
|
- Kelley Fleming
- 5 years ago
- Views:
Transcription
1 TRANSZORB Transient Voltage Suppressors PRIMARY CHARACTERISTICS V WM 5.8 V to 459 V V BR uni-directional 6.8 V to 54 V V BR bi-directional 6.8 V to 44 V P PPM 4 W P D 1.5 W I FSM (uni-directional only) 4 A T J max. 175 C Polarity Uni-directional, bi-directional Package DEVICES FOR BI-DIRECTION APPLICATIONS For bi-directional types, use CA suffix (e.g. P4KE44CA). Electrical characteristics apply in both directions. FEATURES Glass passivated chip junction Available in uni-directional and bi-directional 4 W peak pulse power capability with a / μs waveform, repetitive rate (duty cycle):.1 % Excellent clamping capability Very fast response time Low incremental surge resistance Solder dip 275 C max. s, per JESD 22-B6 AEC-Q1 qualified Material categorization: for definitions of compliance please see TYPICAL APPLICATIONS Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, automotive, and telecommunication. MECHANICAL DATA Case:, molded epoxy body over passivated chip Molding compound meets UL 94 V- flammability rating Base P/N-E3 - RoHS-compliant, commercial grade Base P/NHE3 - RoHS-compliant, AEC-Q1 qualified Terminals: matte tin plated leads, solderable per J-STD-2 and JESD 22-B2 E3 suffix meets JESD 21 class 1A whisker test, HE3 suffix meets JESD 21 class 2 whisker test Note P4KE25CA to P4KE54A and P4KE25A to P4KE44CA for commercial grade only Polarity: for uni-directional types the color band denotes cathode end, no marking on bi-directional types RATINGS (T A = 25 C unless otherwise noted) PARAMETER SYMBOL LIMIT UNIT Peak pulse power dissipation with a / μs waveform (1) (fig.1) P PPM 4 W Peak pulse current with a / μs waveform (1) See next table A Power dissipation on infinite heatsink at T L = 75 C (fig. 5) P D 1.5 W Peak forward surge current 8.3 ms single half-sine wave uni-directional only (2) I FSM 4 A Maximum instantaneous forward voltage at 25 A for uni-directional only (3) V F 3.5/5. V Operating junction and storage temperature range T J, T STG - 55 to C Notes (1) Non-repetitive current pulse, per fig. 3 and derated above T A = 25 C per fig. 2 (2) 8.3 ms single half-sine wave or equivalent square wave, duty cycle = 4 pulses per minute maximum (3) V F = 3.5 V for P4KE22A and below; V F = 5. V for P4KE25A and above Revision: 16-Jan-18 1 Document Number: ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
2 ELECTRICAL CHARACTERISTICS (T A = 25 C unless otherwise noted) DEVICE TYPE BREAKDOWN V BR AT I T (1) (V) MAX. TEST CURRENT I T (ma) STAND-OFF V WM (V) REVERSE LEAKAGE AT V WM I D (3) (μa) PEAK PULSE CURRENT (2) (A) CLAMPING AT V C (V) TEMPERATURE COEFFICIENT AT V BR (%/ C) P4KE6.8A P4KE7.5A P4KE8.2A P4KE9.1A P4KEA P4KE11A P4KE12A P4KE13A P4KE15A P4KE16A P4KE18A P4KE2A P4KE22A P4KE24A P4KE27A P4KE3A P4KE33A P4KE36A P4KE39A P4KE43A P4KE47A P4KE51A P4KE56A P4KE62A P4KE68A P4KE75A P4KE82A P4KE91A P4KEA P4KE1A P4KE12A P4KE13A P4KE15A P4KE16A P4KE17A P4KE18A P4KE2A P4KE22A P4KE25A P4KE3A P4KE35A P4KE4A P4KE44A P4KE48A P4KE5A P4KE54A Notes (1) Pulse test: t p 5 ms (2) Surge current waveform per fig. 3 and derate per fig. 2 (3) For bi-directional types with V WM of V and less the I D limit is doubled (4) All terms and symbols are consistent with ANSI/EEE CA62.35 Revision: 16-Jan-18 2 Document Number: ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
3 Peak Pulse Power (P PP ) or Current (I PP ) Derating in Percentage (%) P PPM - Peak Pulse Power (kw) THERMAL CHARACTERISTICS (T A = 25 C unless otherwise noted) PARAMETER SYMBOL VALUE UNIT Typical thermal resistance, junction to lead R JL 66 C/ W Typical thermal resistance, junction to ambient L Lead = mm R JA ORDERING INFORMATION (Example) PREFERRED PIN UNIT WEIGHT (g) PREFERRED PACKAGE CODE BASE QUANTITY DELIVERY MODE P4KE6.8A-E3/ " diameter paper tape and reel P4KE6.8AHE3/54 (1) " diameter paper tape and reel Note (1) AEC-Q1 qualified RATINGS AND CHARACTERISTICS CURVES (T A = 25 C unless otherwise noted) 1 Non-Repetitive Pulse Waveform shown in Fig. 3 T A = 25 C t d - Pulse Width (µs) Fig. 1 - Peak Pulse Power Rating Curve - Peak Pulse Current, % I RSM 15 5 t r = µs Peak Value Half Value - I PP 2 t d t - Time (ms) T J = 25 C Pulse Width (t d ) is defined as the Point where the Peak Current Decays to 5 % of / µs Waveform as defined by R.E.A. Fig. 3 - Pulse Waveform C J - Junction Capacitance (pf) Measured at Stand-Off Voltage V WM T J = 25 C f = 1. MHz V sig = 5 mv p-p Measured at Zero Bias T J - Initial Temperature ( C) Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature 1 V BR - Breakdown Voltage (V) Fig. 4 - Typical Junction Capacitance Uni-Directional Revision: 16-Jan-18 3 Document Number: ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
4 Transient Thermal Impedance ( C/W) P D - Power Dissipation (%) L =.375" (9.5 mm) Lead Lengths 6 Hz Resistive or Inductive Load T L - Lead Temperature ( C) Fig. 5 - Power Derating Curve t p - Pulse Duration (s) Fig. 7 - Typical Transient Thermal Impedance Peak Forward Surge Current (A) T J = T J Max. 8.3 ms Single Half Sine-Wave 1 Number of Cycles at 6 Hz Fig. 6 - Maximum Non-Repetitive Forward Surge Current Uni-Directional Only PACKAGE OUTLINE DIMENSIONS in inches (millimeters).7 (2.7).8 (2.) DIA. 1. (25.4).25 (5.2).16 (4.1).26 (.66).23 (.58) DIA. 1. (25.4) Revision: 16-Jan-18 4 Document Number: ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
5 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. 217 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 8-Feb-17 1 Document Number: 9
P6KE6.8A thru P6KE540A. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. FEATURES PRIMARY CHARACTERISTICS
TRANSZORB Transient Voltage Suppressors DO-204AC (DO-15) PRIMARY CHARACTERISTICS V WM 5.8 V to 459 V V BR uni-directional 6.8 V to 540 V V BR bi-directional 6.8 V to 440 V P PPM 600 W P D 5.0 W I FSM (uni-directional
More informationICTE5 thru ICTE18C, 1N6373 thru 1N6386. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor.
TRANSZORB Transient Voltage Suppressors Case Style 1.5KE PRIMARY CHARACTERISTICS V WM 5. V to 18 V V BR (uni-directional) 6. V to 21.2 V V BR (bi-directional) 9.2 V to 21.2 V P PPM 1 W P D 6.5 W I FSM
More information5KP8.5A thru 5KP188A. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. FEATURES TYPICAL APPLICATIONS
TRANSZORB Transient Voltage Suppressors P6 PRIMARY CHARACTERISTICS V WM 8.5 V to 188 V V BR 9.4 V to 231 V P PPM 5 W P D 8. W I FSM 5 A T J max. 175 C Polarity Uni-directional Package P6 FEATURES P6 glass
More informationSurface Mount TRANSZORB Transient Voltage Suppressors
Surface Mount TRANSZORB Transient Voltage Suppressors PRIMARY CHARACTERISTICS V WM (uni-directional) 5.8 V to 459 V V WM (bi-directional) 5.8 V to 185 V V BR (uni-directional) 6.8 V to 540 V V BR (bi-directional)
More informationSA5.0A thru SA170CA. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. FEATURES PRIMARY CHARACTERISTICS
TRANSZORB Transient Voltage Suppressors DO-204AC (DO-15) PRIMARY CHARACTERISTICS V WM 5.0 V to 170 V V BR (uni-directional) 6.4 V to 209 V V BR (bi-directional) 6.4 V to 209 V P PPM 500 W P D 3.0 W I FSM
More informationSA5.0A thru SA170CA. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. FEATURES PRIMARY CHARACTERISTICS
TRANSZORB Transient Voltage Suppressors DO-204AC (DO-15) PRIMARY CHARACTERISTICS V WM 5.0 V to 170 V P PPM 500 W P D 3.0 W I FSM (uni-directional only) 70 A T J max. 175 C DEVICES FOR BI-DIRECTION APPLICATIONS
More informationHigh Power Density Surface Mount TRANSZORB Transient Voltage Suppressors
High Power Density Surface Mount TRANSZORB Transient Voltage Suppressors PRIMARY CHARACTERISTICS V BR 6.4 V to 49.1 V V WM 5.0 V to 40 V P PPM 0 W I FSM (uni-directional only) 40 A T J max. 1 C Polarity
More informationHigh Temperature Stability and High Reliability Conditions FEATURES
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions PRIMARY CHARACTERISTICS V WM 1 V to 43 V V BR 11.1 V to 52.8 V P PPM 3 W P D 6. W I FSM 2 A T
More informationSurface Mount TRANSZORB Transient Voltage Suppressors
Surface Mount TRANSZORB Transient Voltage Suppressors esmp Series PRIMARY CHARACTERISTICS V BR uni-directional 4. V to 44.2 V V WM 3.3 V to 36 V P PPM 400 W I FSM 40 A T J max. 150 C Polarity Uni-directional
More informationSurface Mount TRANSZORB Transient Voltage Suppressors
Surface Mount TRANSZORB Transient Voltage Suppressors PRIMARY CHARACTERISTICS V BR 6.8 V to 220 V V WM 5.8 V to 188 V P PPM 600 W P D 5.0 W I FSM (uni-directional only) A T J max. 150 C Polarity Uni-directional,
More informationHigh Temperature Stability and High Reliability Conditions FEATURES
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions DO-218 Compatible PRIMARY CHARACTERISTICS V BR 11.1 V to 52.8 V P PPM (1 x μs) 66 W P PPM (1 x
More informationMSP3V3, MSP5.0A. Surface Mount TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. FEATURES. Series.
Surface Mount TRANSZORB Transient Voltage Suppressors esmp Series Top View Bottom View PRIMARY CHARACTERISTICS V WM 3.3 V to 5. V V BR 4.1 V to 7.7 V P PPM 15 W T J max. 15 C Polarity Uni-directional Package
More informationHigh Temperature Stability and High Reliability Conditions FEATURES
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions DO-28AB PRIMARY CHARACTERISTICS V BR 27 V P PPM ( x μs) 36 W P D 5 W V WM 22 V I RSM 7 A I FSM
More informationSurface Mount TRANSZORB Transient Voltage Suppressors
Surface Mount TRANSZORB Transient Voltage Suppressors PRIMARY CHARACTERISTICS V WM 5.80 V to 188 V V BR uni-directional 6.8 V to 220 V V BR bi-directional 6.8 V to 220 V P PPM 600 W P D 5.0 W I FSM (uni-directional
More informationHigh Temperature Stability and High Reliability Conditions FEATURES. PARAMETER SYMBOL VALUE UNIT with 10/1000 μs waveform Peak pulse power dissipation
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions PRIMARY CHARACTERISTICS V WM 1 V to 36 V V BR 11.1 V to 44.2 V P PPM (1 x 1 μs) 36 W P PPM (1
More informationNew Product. High Temperature Stability and High Reliability Conditions FEATURES
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions PRIMARY CHARACTERISTICS V WM 1 V to 43 V V BR 11.1 V to 52.8 V P PPM 3 W P D 6. W I FSM 2 A T
More informationHigh Temperature Stability and High Reliability Conditions FEATURES
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions SMB (DO-214AA) PRIMARY CHARACTERISTICS V BR 6.8 V to 43 V V WM 5.8 V to 36.8 V P PPM 600 W I FSM
More informationGlass Passivated Ultrafast Plastic Rectifier
Glass Passivated Ultrafast Plastic Rectifier SUPERECTIFIER DO-204AL (DO-4) FEATURES Superectifier structure for high reliability condition Cavity-free glass-passivated junction Ideal for printed circuit
More informationUF4001, UF4002, UF4003, UF4004, UF4005, UF4006, UF4007 Ultrafast Plastic Rectifier
UF400, UF4002, UF4003, UF4004, UF4005, UF4006, UF4007 Ultrafast Plastic Rectifier FEATURES Glass passivated chip junction Ultrafast reverse recovery time Low forward voltage drop Low switching losses,
More informationHigh Power Density Surface Mount PAR Transient Voltage Suppressors
High Power Density Surface Mount PAR Transient Voltage Suppressors esmp Series DO-22AA (SMP) PRIMARY CHARACTERISTICS V BR 6.8 V to 43 V V WM 5.8 V to 36.8 V P PPM (for V BR 6.8 V) 25 W P PPM (for V BR
More informationGlass Passivated Junction Plastic Rectifier
N400GP, N4002GP, N4003GP, N4004GP, N4005GP, N4006GP, N4007GP Glass Passivated Junction Plastic Rectifier SUPERECTIFIER DO-204AL (DO-4) FEATURES Superectifier structure for high reliability application
More informationGeneral Purpose Plastic Rectifier
General Purpose Plastic Rectifier N400 thru N4007 DO-204AL (DO-4) FEATURES Low forward voltage drop Low leakage current High forward surge capability Solder dip 275 C max. s, per JESD 22-B6 Compliant to
More informationBi-directional 1500 W TVS in TO-277 (SMPC) Package FEATURES
Surface Mount PAR Transient Voltage Suppressors Bi-directional 1500 W TVS in TO-277 (SMPC) Package esmp Series Terminal 1 Terminal 2 FEATURES Junction passivation optimized PAR design T J = 185 C capability
More informationSurface Mount Ultrafast Plastic Rectifier
Surface Mount Ultrafast Plastic Rectifier PRIMARY CHARACTERISTICS I F(AV) 1.0 A V RRM 200 V I FSM 40 A t rr 25 ns V F 0.71 V T J max. 175 C Package Diode variations Single die FEATURES Glass passivated
More informationPhotovoltaic Solar Cell Protection Schottky Rectifier
VSB545-M3 Photovoltaic Solar Cell Protection Schottky Rectifier Ultra Low V F =.33 V at I F = 5. A TMBS FEATURES Trench MOS Schottky technology Low forward voltage drop, low power losses High efficiency
More informationDual Common Cathode Ultrafast Rectifier
UGEBCT, UGECCT, UGEDCT Dual Common Cathode Ultrafast Rectifier PIN PIN 3 UGExCT PIN 2 CASE PRIMARY CHARACTERISTICS 2 3 I F(AV) 2 x 5.0 A V RRM 0 V, 50 V, 200 V I FSM 55 A t rr 25 ns V F 0.895 V T J max.
More informationSurface Mount Power Voltage-Regulating Diodes
Surface Mount Power Voltage-Regulating Diodes DO-24AC (SMA) FEATURES Low profile package Ideal for automated placement Low Zener impedance Low regulation factor Meets MSL level, per J-STD-2, if maximum
More informationHigh Current Density Surface Mount Schottky Barrier Rectifiers
High Current Density Surface Mount Schottky Barrier Rectifiers esmp Series 2 Anode Cathode Anode 2 FEATURES Very low profile - typical height of. mm Available Ideal for automated placement Low forward
More informationHigh Temperature Stability and High Reliability Conditions FEATURES
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions DESIGN SUPPORT TOOLS Models Available Top View Cathode esmp Series Bottom View PRIMARY CHARACTERISTICS
More informationHigh Voltage Glass Passivated Junction Plastic Rectifier
High Voltage Glass Passivated Junction Plastic Rectifier SUPERECTIFIER FEATURES Superectifier structure for high reliability application Cavity-free glass-passivated junction Low leakage current High forward
More informationDual Common-Cathode Ultrafast Rectifier
Dual Common-Cathode Ultrafast Rectifier TO-22AB BYV32 Series PIN PIN 3 CASE 2 3 TO-263AB ITO-22AB 2 3 BYVF32 Series PIN PIN 3 2 FEATURES Power pack Glass passivated pellet chip junction Ultrafast recovery
More informationHigh Temperature Stability and High Reliability Conditions FEATURES
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions Top View SlimSMA TM DO-22AC PRIMARY CHARACTERISTICS V BR 6.8 V to 5 V 5.8 V to 43.6 V P PPM (
More informationHigh Temperature Stability and High Reliability Conditions FEATURES
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions DESIGN SUPPORT TOOLS Models Available Top View Cathode esmp Series Bottom View PRIMARY CHARACTERISTICS
More informationSurface Mount Glass Passivated Rectifier
Surface Mount Glass Passivated Rectifier DO-24AC (SMA) PRIMARY CHARACTERISTICS I F(AV) 2.0 A V RRM 200 V, 400 V, 600 V, 800 V, 00 V I FSM 50 A I R 5.0 μa V F at I F = 2.0 A (T A = 25 C) 0.90 V T J max.
More informationHigh Current Density Surface Mount Ultrafast Rectifiers
High Current Density Surface Mount Ultrafast Rectifiers esmp Series PRIMARY CHARACTERISTICS I F(AV).0 A V RRM 0 V, 50 V, 200 V t rr 25 ns V F 0.90 V T J max. 75 C Package Diode variations Single die FEATURES
More informationHigh Current Density Surface Mount Schottky Barrier Rectifiers
SSP3C, SSP4C High Current Density Surface Mount Schottky Barrier Rectifiers esmp Series 2 Anode FEATURES Very low profile - typical height of. mm Available Ideal for automated placement Low forward voltage
More informationHigh Temperature Stability and High Reliability Conditions FEATURES
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions PRIMARY CHARACTERISTICS V BR 6.8 V to 43 V V WM 5.50 V to 36.8 V P PPM 600 W I FSM 75 A T J max.
More informationPhotovoltaic Solar Cell Protection Schottky Rectifier
Photovoltaic Solar Cell Protection Schottky Rectifier Ultra Low V F = 0.30 V at I F = 5.0 A FEATURES TMBS Trench MOS Schottky technology Low forward voltage drop, low power losses High efficiency operation
More informationDual Common Cathode Ultrafast Plastic Rectifier
Dual Common Cathode Ultrafast Plastic Rectifier TO-2AB UGE8xCT PIN PIN 2 3 2 FEATURES Power pack Glass passivated pellet chip junction Ultrafast recovery time Low switching losses, high efficiency Low
More informationFEATURES. Package. PARAMETER SYMBOL PB3506 PB3508 PB3510 UNIT Maximum repetitive peak reverse voltage V RRM V 35 T A = 25 C (2) 4.
PB356, PB358, PB35 Enhanced isocink+ TM Bridge Rectifiers + isocink+ ~ ~ - - ~ ~ + ~ ~ Case Style PB FEATURES UL recognition file number E32394 (QQQX2) UL 557 (see *) Enhanced high-current density single
More informationHigh Temperature Stability and High Reliability Conditions FEATURES
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions PRIMARY CHARACTERISTICS V BR 6.8 V to 47 V V WM 5. V to 40.2 V P PPM 10 W I FSM 200 A T J max.
More informationSurface Mount Ultrafast Plastic Rectifier
Surface Mount Ultrafast Plastic Rectifier DO-24AB (SMC) PRIMARY CHARACTERISTICS I F(AV) 3. A V RRM 3 V, 4 V I FSM A t rr 35 ns V F at I F. V T J max. 5 C Package DO-24AB (SMC) Diode variations Single die
More informationSMC5K10A thru SMC5K85A. Surface Mount TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor.
Surface Mount TRANSZORB Transient Voltage Suppressors PRIMARY CHARACTERISTICS V BR 11.1 V to 104 V V WM 10 V to 85 V P PPM 5000 W T J max. 150 C Polarity Uni-directional Package TYPICAL APPLICATIONS Use
More informationHigh Current Density Surface Mount Dual Common Cathode Schottky Rectifier
High Current Density Surface Mount Dual Common Cathode Schottky Rectifier esmp Series K 2 K Anode Cathode Anode 2 FEATURES Very low profile - typical height of. mm Available Ideal for automated placement
More informationUltrafast Avalanche SMD Rectifier
Ultrafast Avalanche SMD Rectifier PRIMARY CHARACTERISTICS I F(AV) 1.5 A V RRM V I FSM 3 A I R 5. μa t rr 75 ns V F 1.7 V E R 2 mj T J max. 15 C Package Diode variations Single FEATURES Low profile package
More informationDual High Voltage Trench MOS Barrier Schottky Rectifier
V300C, VI300C Dual High Voltage Trench MOS Barrier Schottky Rectifier Ultra Low V F = 0.455 V at I F = 5 A TO-220AB 2 3 V300C PIN PIN 2 PIN 3 CASE TMBS TO-262AA K 2 3 VI300C PIN PIN 2 PIN 3 K FEATURES
More informationHigh Current Density Surface Mount Glass Passivated Rectifiers
SPB, SPD, SPG, SPJ, SPK, SPM High Current Density Surface Mount Glass Passivated Rectifiers esmp Series DO-22AA (SMP) FEATURES Very low profile - typical height of. mm Available Ideal for automated placement
More informationSurface Mount Glass Passivated Junction Rectifier
-xxx, GL4x Surface Mount Glass Passivated Junction Rectifier SUPERECTIFIER DO-23AB PRIMARY CHARACTERISTICS I F(AV).0 A V RRM (-xxx, GL4x) 50 V to 00 V, 50 V to 600 V I FSM 30 A I R μa E AS 5 mj V F. V,.2
More informationFast Avalanche SMD Rectifier
BYG2K-E3/HE3, BYG2M-E3/HE3 Fast Avalanche SMD Rectifier SMA (DO-24AC) PRIMARY CHARACTERISTICS I F(AV).5 A V RRM 8 V, V I FSM 3 A I R. μa V F.6 V t rr 2 ns E R 2 mj T J max. 5 C Package SMA (DO-24AC) Diode
More informationFEATURES. Package. PARAMETER SYMBOL PB4006 PB4008 PB4010 UNIT Maximum repetitive peak reverse voltage V RRM V
Enhanced isocink+ TM Bridge Rectifiers + isocink+ ~ ~ - - ~ ~ + ~ ~ Case Style PB FEATURES UL recognition file number E32394 (QQQX2) UL 557 (see *) Enhanced high-current density single in-line package
More informationUltrafast Avalanche SMD Rectifier
Ultrafast Avalanche SMD Rectifier PRIMARY CHARACTERISTICS I F(AV) 1.5 A V RRM 1 V I FSM 3 A I R 5. μa t rr 75 ns V F 1.7 V E R 2 mj T J max. 15 C Package Circuit configuration Single FEATURES Low profile
More informationMSP5.0A. Surface Mount TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. New Product
MSP5.A Surface Mount TRANSZORB Transient Voltage Suppressors esmp TM Series Top View Bottom View MicroSMP PRIMARY CHARACTERISTICS V WM 5. V P PPM W I FSM 25 A T J max. 5 C FEATURES Very low profile - typical
More informationHigh Current Density Surface Mount High Voltage Schottky Rectifiers
SSPH9, SSPH High Current Density Surface Mount High Voltage Schottky Rectifiers esmp Series 2 Anode Cathode Anode 2 FEATURES Power pack Available Very low profile - typical height of. mm Ideal for automated
More informationEnhanced isocink+ Bridge Rectifiers
Enhanced isocink+ Bridge Rectifiers - ~ ~ + isocink+ Case Style BU PRIMARY CHARACTERISTICS Package BU I F(AV) 5 A V RRM 6 V, 8 V, V I FSM 2 A I R 5 μa V F at I F = 7.5 A.87 V T J max. 5 C Circuit configuration
More informationDual High Voltage Trench MOS Barrier Schottky Rectifier
MBRF9CT-M3, MBRFCT-M3 Dual High Voltage Trench MOS Barrier Schottky Rectifier TMBS ITO-22AB 2 3 PIN PIN 2 PIN 3 PRIMARY CHARACTERISTICS I F(AV) 2 x 5. A V RRM 9 V, V I FSM 2 A V F.75 V T J max. 5 C Package
More informationSMD Photovoltaic Solar Cell Protection Rectifier
SMD Photovoltaic Solar Cell Protection Rectifier esmp Series 2 Anode Cathode Anode 2 FEATURES Very low profile - typical height of. mm Ideal for automated placement Glass passivated pellet chip junction
More informationUltrafast Rectifier FEATURES
Ultrafast Rectifier TO-AC ITO-AC BYW9 Series BYWF9 Series PIN PIN CASE D PA (TO-63AB) BYWB9 Series PIN HEATSIN DESIGN SUPPORT TOOLS click logo to get started FEATURES Power pack Glass passivated pellet
More informationFast Switching Avalanche Surface Mount Rectifiers
Fast Switching Avalanche Surface Mount Rectifiers esmp Series Cathode 2 Anode Anode 2 FEATURES Very low profile - typical height of. mm Available Ideal for automated placement Glass passivated pellet chip
More informationHigh-Voltage Trench MOS Barrier Schottky Rectifier
V2050SG, VI2050SG High-Voltage Trench MOS Barrier Schottky Rectifier Ultra Low V F = 0.57 V at I F = 5 A TO-220AB V2050SG PIN PIN 2 PIN 3 CASE TMBS TO-262AA K 2 3 2 3 VI2050SG PIN PIN 2 PIN 3 K FEATURES
More informationHigh Power Density Surface Mount PAR Transient Voltage Suppressors
High Power Density Surface Mount PAR Transient Voltage Suppressors esmp Series DO-22AA (SMP) PRIMARY CHARACTERISTICS V BR 6.8 V to 43 V P PPM (for V BR 6.8 V) 25 W P PPM (for V BR 7.5 V to 12 V) 3 W P
More informationSurface Mount Trench MOS Barrier Schottky Rectifier
Surface Mount Trench MOS Barrier Schottky Rectifier TMBS SMPA TM Top View Bottom View DO-22BC (SMPA) FEATURES Very low profile - typical height of 0.95 mm Ideal for automated placement Trench MOS Schottky
More informationSurface Mount Ultrafast Plastic Rectifier
Surface Mount Ultrafast Plastic Rectifier SMA (DO-24AC) PRIMARY CHARACTERISTICS I F(AV). A V RRM 5 V, V, 5 V, 2 V I FSM 3 A t rr 5 ns V F at I F.92 V T J max. 5 C Package SMA (DO-24AC) Diode variations
More informationHigh Current Density Surface Mount High Voltage Schottky Rectifier
High Current Density Surface Mount High Voltage Schottky Rectifier SS8PH9, SS8PH0 FEATURES esmp Series Very low profile - typical height of. mm Available Ideal for automated placement Guardring for overvoltage
More informationDual Common Cathode High Voltage Schottky Rectifier
Dual Common Cathode High Voltage Schottky Rectifier High Barrier Technology for Improved High Temperature Performance TO-220AB MBR20HCT PIN PIN 3 PRIMARY CHARACTERISTICS I F(AV) 2 x 0 A V RRM V I FSM 250
More informationUltrafast Avalanche Surface Mount Rectifiers
Ultrafast Avalanche Surface Mount Rectifiers esmp Series FEATURES Very low profile - typical height of. mm Available Ideal for automated placement Glass passivated pellet chip junction Fast reverse recovery
More informationTrench MOS Barrier Schottky Rectifier for PV Solar Cell Bypass Protection
Trench MOS Barrier Schottky Rectifier for PV Solar Cell Bypass Protection Ultra Low V F = 0.33 V at I F = A TMBS 2 VBT6045CBP PIN PIN 2 HEATSIN PRIMARY CHARACTERISTICS I F(AV) 2 x 30 A V RRM 45 V I FSM
More informationSurface Mount Ultrafast Plastic Rectifier
Surface Mount Ultrafast Plastic Rectifier PRIMARY CHARACTERISTICS I F(AV) 3. A V RRM 5 V, V, 15 V, 2 V I FSM A t rr 2 ns V F.9 V T J max. 15 C Package Diode variations Single FEATURES Glass passivated
More informationUltrafast Avalanche SMD Rectifier
Ultrafast Avalanche SMD Rectifier SMA (DO-24AC) PRIMARY CHARACTERISTICS I F(AV) 2. A V RRM 5 V, V, 2 V I FSM 35 A I R. μa V F at I F. V t rr 25 ns E R 2 mj T J max. 5 C Package SMA (DO-24AC) Diode variations
More informationHigh Voltage Schottky Rectifier
MB0H90, MB0H, MF0H High Voltage Schottky Rectifier High Barrier Technology for Improved High Temperature Performance ITO-220AC D 2 PA (TO-263AB) 2 2 MB0H90 MF0H MB0H PIN PIN PIN 2 PIN 2 HEATSIN PRIMARY
More informationUltrafast Plastic Rectifier
8xT, F8xT, B8xT Ultrafast Plastic Rectifier TO-0AC ITO-0AC FEATURES Power pack Glass passivated pellet chip junction Ultrafast recovery time Low switching losses, high efficiency 8xT PIN F8xT PIN Low leakage
More informationTrench MOS Barrier Schottky Rectifier for PV Solar Cell Bypass Protection
www.vishay.com Trench MOS Barrier Schottky Rectifier for PV Solar Cell Bypass Protection Ultra Low V F = 0.28 V at I F = 5 A TMBS ITO-220AC PIN PIN 2 PRIMARY CHARACTERISTICS I F(DC) 40 A V RRM 45 V I FSM
More informationSurface Mount Ultra Fast Rectifier
USA, USB, USD, USG, USJ, USK, USM Surface Mount Ultra Fast Rectifier SMA (DO-24AC) PRIMARY CHARACTERISTICS I F(AV).0 A 50 V, 0 V, 200 V, 400 V, 600 V, V RRM 800 V, 00 V I FSM 30 A t rr 50 ns, 75 ns V F
More informationFEATURES. PARAMETER SYMBOL V8PAM10 UNIT Device marking code Maximum repetitive peak reverse voltage V RRM 100 V
Surface-Mount TMBS (Trench MOS Barrier Schottky) Rectifier esmp Series Top View Bottom View Anode Cathode FEATURES Very low profile - typical height of 0.95 mm Ideal for automated placement Trench MOS
More informationSurface Mount Trench MOS Barrier Schottky Rectifier
Surface Mount Trench MOS Barrier Schottky Rectifier TMBS esmp Series Top View SlimSMA (DO-22AC) Cathode DESIGN SUPPORT TOOLS Models Available Bottom View PRIMARY CHARACTERISTICS Anode click logo to get
More informationSMPC5.0A thru SMPC36A, SMPC22AN thru SMPC85AN Surface Mount TRANSZORB Transient Voltage Suppressors
Surface Mount TRANSZORB Transient Voltage Suppressors DESIGN SUPPORT TOOLS Models Available SMPCxxA SMPCxxAN esmp Series 2 SMPC (TO-277A) A Anode K Cathode 1 Cathode 1 Cathode 2 Anode 1 Anode 2 click logo
More informationDual Common Cathode Ultrafast Plastic Rectifier
6xT, F6xT, B6xT Dual Common Cathode Ultrafast Plastic Rectifier TO-220AB ITO-220AB FEATURES Power pack Glass passivated pellet chip junction Ultrafast recovery time Low switching losses, high efficiency
More informationPhotovoltaic Solar Cell Protection Schottky Rectifier
Photovoltaic Solar Cell Protection Schottky Rectifier Ultra Low V F =.3 V at I F = 5. A TMBS FEATURES Trench MOS Schottky technology Low forward voltage drop, low power losses High efficiency operation
More informationUltrafast Plastic Rectifier
Ultrafast Plastic Rectifier 6xT, F6xT, B6xT TO-0AC 6xT Series PIN CASE ITO-0AC F6xT Series PIN D PA (TO-63AB) B6xT Series PIN HEATSIN FEATURES Power pack Glass passivated pellet chip junction Ultrafast
More informationSurface Mount Trench MOS Barrier Schottky Rectifier
Surface Mount Trench MOS Barrier Schottky Rectifier TMBS esmp Series Top View Bottom View SlimSMA (DO-22AC) Cathode Anode FEATURES Very low profile - typical height of 0.95 mm Ideal for automated placement
More informationHigh Current Density Surface Mount Trench MOS Barrier Schottky Rectifier
V5PL50 High Current Density Surface Mount Trench MOS Barrier Schottky Rectifier Ultra Low V F = 0.8 V at I F = 5 A TMBS esmp Series Anode Cathode Anode PRIMARY CHARACTERISTICS I F(AV) 5 A V RRM 50 V I
More informationSchottky Barrier Rectifier
Schottky Barrier Rectifier TO-0AC ITO-0AC FEATURES Power pack Low power loss, high efficiency Low forward voltage drop High forward surge capability High frequency operation CASE D PA (TO-63AB) MBRF045
More informationUltrafast Avalanche Surface Mount Rectifiers
Ultrafast Avalanche Surface Mount Rectifiers DESIGN SUPPORT TOOLS Models Available esmp Series PRIMARY CHARACTERISTICS Cathode I F(AV) 2.0 A V RRM 200 V, 400 V, 600 V I FSM 30 A t rr 75 ns E AS 20 mj V
More informationHigh Current Density Surface Mount Trench MOS Barrier Schottky Rectifier
V40PWM2C High Current Density Surface Mount Trench MOS Barrier Schottky Rectifier Ultra Low V F = 0.50 V at I F = 5 A TMBS esmp Series 2 SlimDPAK (TO-252AE) PIN K K FEATURES Very low profile - typical
More informationHigh Voltage Ultrafast Avalanche SMD Rectifiers
High Voltage Ultrafast Avalanche SMD Rectifiers PRIMARY CHARACTERISTICS I F(AV) DO-24AC (SMA).0 A FEATURES Glass passivated pellet chip junction Low profile package Ideal for automated placement Low reverse
More informationSurface Mount Ultrafast Plastic Rectifier
Surface Mount Ultrafast Plastic Rectifier SMC (DO-24AB) PRIMARY CHARACTERISTICS I F(AV) 3. A V RRM 4 V, 6 V I FSM 25 A t rr 5 ns V F.5 V T J max. 75 C Package SMC (DO-24AB) Diode variation Single FEATURES
More informationSMD Photovoltaic Solar Cell Protection Schottky Rectifier
SSP4S SMD Photovoltaic Solar Cell Protection Schottky Rectifier PRIMARY CHARACTERISTICS I F(AV) A V RRM 40 V I FSM 80 A E AS 0 mj V F at I F = A 0.43 V T J max. 50 C Package Diode variations Single die
More informationSurface-Mount Glass Passivated Rectifier
Surface-Mount Glass Passivated Rectifier DESIGN SUPPORT TOOLS Models Available Top View Cathode esmp Series Bottom View PRIMARY CHARACTERISTICS Anode click logo to get started I F(AV).0 A V RRM 400 V,
More informationSurface Mount Trench MOS Barrier Schottky Rectifier
Surface Mount Trench MOS Barrier Schottky Rectifier TMBS SMPA TM Top View Bottom View DO-22BC (SMPA) PRIMARY CHARACTERISTICS I F(AV) 3.0 A V RRM 50 V I FSM 80 A V F at I F = 3.0 A (T A = 25 C) 0.40 V T
More informationSurface Mount Schottky Barrier Rectifier
Surface Mount Schottky Barrier Rectifier esmp Series Top view Bottom view DO-29AB (SMF) PRIMARY CHARACTERISTICS I F(AV) 2.0 A V RRM 0 V I FSM 50 A V F at I F = 2.0 A () 0.63 V T J max. 75 C Package DO-29AB
More informationSurface Mount Fast Avalanche Rectifiers
ARPD, ARPG, ARPJ, ARPK, ARPM Surface Mount Fast Avalanche Rectifiers esmp Series DO-22AA (SMP) PRIMARY CHARACTERISTICS I F(AV). A V RRM 2 V, 4 V, 6 V, 8 V, V I FSM 3 A, 25 A t rr 4 ns, 2 ns V F.5 V,.4
More informationDual High-Voltage Trench MOS Barrier Schottky Rectifier
V60D0C-M3, V60D0CHM3 Dual High-Voltage Trench MOS Barrier Schottky Rectifier Ultra Low V F = 0.36 V at I F = 5 A 2 TMBS esmp Series Top View K PIN V60D0C Bottom View K FEATURES Trench MOS Schottky technology
More informationSurface Mount Schottky Barrier Rectifier
Surface Mount Schottky Barrier Rectifier esmp Series Top view Bottom view SMF (DO-219AB) Cathode Anode FEATURES Low profile package Available Ideal for automated placement Low forward voltage drop, low
More informationSurface Mount Standard Rectifiers
Surface Mount Standard Rectifiers Top view esmp Series DO-29AB (SMF) PRIMARY CHARACTERISTICS I F(AV).0 A V RRM 200 V, 400 V, 600 V I FSM 25 A V F at I F =.0 A (T A = 25 C) 0.85 V I R 5 μa T J max. 75 C
More informationTrench MOS Barrier Schottky Rectifier for PV Solar Cell Bypass Protection
www.vishay.com Trench MOS Barrier Schottky Rectifier for PV Solar Cell Bypass Protection Ultra Low V F = 0.4 V at I F = 5 A VBT045BP-E3 TMBS DESIGN SUPPORT TOOLS Models Available PRIMARY CHARACTERISTICS
More informationGlass Passivated Power Voltage-Regulating Diodes
Z4KE0A thru Z4KE200A Glass Passivated Power Voltage-Regulating Diodes DO-204AL (DO-4) FEATURES Plastic MELF package Ideal for automated placement Glass passivated chip junction Low Zener impedance Low
More informationUltrafast Avalanche SMD Rectifier
Ultrafast Avalanche SMD Rectifier DO-24AC (SMA) FEATURES Low profile package Ideal for automated placement Glass passivated pallet chip junction Low reverse current Low forward voltage Soft recovery characteristic
More informationDual Common Cathode Ultrafast Rectifier
BYQ28E-xxx, BYQ28EF-xxx, BYQ28EB-xxx, UG0xCT, UGF0xCT, UGB0xCT Dual Common Cathode Ultrafast Rectifier BYQ28E, UG0 PIN PIN 3 TO-220AB CASE BYQ28EB, UGB0 PIN 2 3 DESIGN SUPPORT TOOLS Models Available D
More informationHigh Current Density Surface Mount Trench MOS Barrier Schottky Rectifier
High Current Density Surface Mount Trench MOS Barrier Schottky Rectifier Ultra Low V F = 0.34 V at I F = 4 A TMBS esmp Series TO-77A (SMPC) Anode Cathode Anode PRIMARY CHARACTERISTICS I F(AV) 8.0 A V RRM
More informationGeneral Purpose Plastic Rectifier
General Purpose Plastic Rectifier N400 thru N4007 DO-204AL (DO-4) PRIMARY CHARACTERISTICS I F(AV).0 A V RRM V to 00 V I FSM (8.3 ms sine-wave) A I FSM (square wave t p = ms) 45 A V F. V I R 5.0 µa T J
More informationUni-directional 1500 W TVS in TO-277 (SMPC) Package FEATURES
Surface Mount PR Transient Voltage Suppressors Uni-directional 500 W TVS in TO-277 (SMPC) Package esmp Series 2 TO-277 (SMPC) PRIMRY CHRCTERISTICS V WM 5.8 V to 43.6 V V BR 6.8 V to 5 V P PPM 500 W T J
More information