EHD2. Ultra Thin Film Measurement System

Transcription

1 EHD2 Ultra Thin Film Measurement System A fully automated bench top, computer controlled instrument for film thickness measurements of lubricants in the elastohydrodynamic (EHD) lubricating regime

2 EHD2 Rig Overview The EHD2 Ultra Thin Film Measurement System is the latest evolution of the successful EHD instrument which to date has sold over 100 systems worldwide. It is now a fully automated computer controlled instrument for measuring the film thickness and traction coefficient (friction coefficient) of lubricants in the elastohydrodynamic (EHD) lubricating regime. The instrument can measure lubricant film thickness down to 1 nm. The contact pressures and shear rates in this contact are similar to those found in, for example, gears, rolling element bearings and cams. In addition to film thickness measurements, traction coefficients can be measured at any slide/roll ratio from pure rolling up to 100%. Principle The instrument measures the lubricant film thickness properties in the contact formed between a ¾ (19.05mm) diameter steel ball and a rotating glass disk by optical interferometry. The lubricant film thickness at any point in the image can be accurately calculated by measuring the wavelength of light at that point. Normally the system measures the wavelength of the light returned from the central plateau of the contact and hence calculates the central film thickness. Automated testing The control software runs on a standard desktop PC and allows the user to easily define a test profile containing a sequence of temperatures, loads and speeds. After setting the initial film thickness, the selected profile steps the instrument through the test sequence, recording data as required, without any intervention by the user. PC monitor displays both analysed image with orders (top) and captured B&W camera image (below) Spectrometer White Light Diffracted image focused on to a fire wire black and white camera Selectable Averaging Bands on the pc Glass disc with thin Cr layer and SiO 2 Spacer Layer Interference image from ball and chrome layer EHD2 Method Load 1) The contact is illuminated by a white light source directed down a microscope through a glass disc on to the contact. 2) Part of the light is reflected from the Cr layer and part travels through the SiO 2 layer and fluid film and is reflected back from the steel ball. 3) Recombining the two light paths forms an interference image which is passed into a spectrometer and high resolution monochrome CCD camera. 4) The camera image is captured by a video frame grabber and analysed by the control software to determine the film thickness.

3 Film Thickness (nm) Film Thickness (nm) Specimens The 3/4 diameter plain standard ball is manufactured from carbon chrome steel and has a high grade surface finish to ensure good reflectivity. The standard glass disc is coated with a semi reflective layer of chromium and approximately 550 nm of silica. A drilled ball can used which can be driven during the test at a set slide/roll ratio (SRR). Although the ball has to be reflective, it can be made from different materials. In the past we have supplied tungsten carbide balls (either plain or drilled) and sapphire discs to enable contact pressures up to 3 GPa Film Thickness Data The two graphs show central film thickness (Y-axis) versus rolling speed (X-axis) at a range of lubricant C 30 C 50 C 80 C 120 C 150 C temperatures. 10 The upper graph is for an additivefree, base oil The lower graph shows the same base oil with the addition of a viscosity index improver (a multifunctional dispersant polyethylene propylene) copolymer). There is a marked increase in the film thickness at low speeds with the VI improver present C 30 C 50 C 80 C 120 C 150 C Applications Rolling Speed (m/s) Applications of the instrument include:- Evaluation of film forming and frictional properties of oils and greases Starvation and reflow characteristics of grease lubricated components Fuel economy prediction of candidate crankcase oils Boundary Performance prediction of oil-in-water emulsion rolling mill lubricants Mixed EHD Fundamental investigations of the high pressure/high shear behaviour of fluids such as liquid crystals Log (U)

4 Spacer Layer Imaging Method (SLIM) on the EHD Rig The Spacer Layer Imaging Method (SLIM) is a natural development of the EHL Thin Film Measurement System. Instead of using a spectrometer to determine the wavelength of the light returned from the image of the EHL contact, SLIM uses a high resolution, RGB (red green, blue) CCD colour camera to grab an image of the whole contact. The SLIM software uses a previously determined colour space calibration to match the colours in the image to oil film thicknesses. The system can thus produce a film thickness map of the whole EHL contact in a few seconds. This makes it a unique tool for examining conditions such as parched or starved lubrication, grease lubrication, rough surface EHL STAGE 1 Produce high resolution image STAGE 2 Acquire high resolution digital image of contact. STAGE 3 Use colour information to determine film thickness within contact or full contact map. Software SLIM Method The software for the system comprises two parts. The first part is the control software which allows the user to conduct a test on the EHD system and acquire images of the contact under user-defined test conditions. The entire test is stored on the PC as a Project and is portable as a subdirectory. Some sample screen shots of the dynamic image acquired during a test are shown below. The second part of the software performs the off-line analysis of the images. The user loads the project into the analysis package which can produce 3D maps of any areas of interest - or the whole contact - at various spacial resolutions. Post processing of the resultant data (a matrix of film thicknesses) can be performed with the supplied software or any other suitable 3D graphing package. Increasing speed Screenshot images acquired during a SLIM test (Increasing Speed left to right)

5 Film thickness (nm) Undeformed height (nm) Height (nm) Inlet Length along entrainment direction (m) Outlet Applications of SLIM The Effects of 3D Model Surface Roughness Features on Lubricant Film Thickness in EHL Contacts Below are some results from work performed at Imperial College 1 on the effect of different surface roughness on lubricant film thickness. A variety of surface finishes have been investigated using the 3D Mapper to measure the film thickness. Single ridge Transverse roughness Isotropic roughness Surface dent Asperity collision Longitudinal vs Transverse Work performed comparing longitudinal and transverse roughness showed that the longitudinal roughness lead to a reduced dynamic lift compared to the transverse roughness and a higher proportion of the contact is borne by longitudinal asperities compared to transverse asperities. Longitudinal roughness Specimen A Microns (m) 1 - From work presented by Choo, Olver, Spikes, Dumont and Ioannides at STLE conference in Las Vegas, May 2005 Application of SLIM to produce 2D profile through centre of contact under different lubrication conditions. fully flooded starved Base oil, 0.1 m/s fully flooded starved 0 50 Contact position (µm) Starvation The 3D SLIM method can be used to investigate parched or starved contacts. The images to the left show the full contact and the 2D profiles through the centre of the contact for both fully flooded and starved conditions.

6 Further Applications Grease Films The images below show residual grease films deposited on the glass spacer layer disc of the EHL system. These images can be analysed to give information about the leakage process by which the rolling track is replenished with oil from the grease matrix. This work is part of an on-going programme of research using the EHL system in the Tribology Laboratory at Imperial College, London. Residual Grease Films on Standard Spacer Layer Disc High Pressure Pot With the optional high pressure pot, pressures from atmospheric to 25 Bar can be set to test both liquids and gasses. There is a pressure indicator, purge valve and sight window to observe the liquid level. This has previously been applied to look at the effect of pressure on refrigerant gases and liquids. Publications EHD High Pressure Pot Some publications for the EHD rig are listed below. For more publications, please visit our web site. Choo, J.W., Olver, A.V. and Spikes, H.A., The influence of transverse roughness in thin film, mixed elastohydrodynamic lubrication. Trib. Intern. 40, pp , (2007). Spikes, H.A., Sixty years of EHL. Lubr. Sci. 18, pp , (2006). Cambiella A., Benito J. M., Pazos C., Coca J., Ratoi M and Spikes H.A. The effect of emulsifier concentration on the lubricating properties of oil-in-water emulsions. Tribology Letters 22, pp , (2006).

7 EHD Accessories and Contact Conditions PCS has developed a range of accessories for the EHD rig. Some of these were developed to extend the capabilities of the instrument, such as the grease scoop which maintains grease within the contact during a test. Others were designed to meet the specialised needs of some customers, such as adapting the ball carriage to enable either an 8 mm or 1/2 diameter ball to used instead of the standard 3/4 ball (to increase the contact pressure). Other accessories can be found on our website: Spherical Roller Carriage The spherical roller produces an elliptical contact and can be used to generate a lower contact pressure for the same applied load. To ensure that pure rolling is maintained, the ball motor is used to drive the roller. Cooler An optional cooler can be connected which circulates silicone cooling oil through the cooling ports in the pot. This can allow a quicker turn-around of tests. The EHD2 cooler comes with an associated switch-box, that automatically switches on at the end of a test and cools the pot down to a pre-defined temperature. Grease Scoop The optional greases scoop consists of a PTFE part connected to a steel block that is attached to the ball carriage. The PTFE block has a channel which guides the grease into the contact ensuring a constant supply of grease through the test. Different Contact Conditions Below are images of some of the contact conditions that are available on the EHD rig. Point Contact - Ball-On-Disc Elliptical Contact - Spherical roller-on-disc Edge Contact - Barrel-on-Disc

8 Technical Specification Specification Film Thickness Load Contact Pressure 1 to 1000 nm 0 to 50 N 0 to 0.7 GPa (steel ball on glass disc) 0 to 3 GPa (WC on sapphire) Speeds Temperature Range Test Sample Volume Control system PC Safety Checks Power Supply Dimensions and weight Mechanical unit Electronics unit 0 to 4 m/s Ambient to 150 C 120 ml Custom software running on Microsoft Windows Dual platinum RTD s for temperature measurement, Emergency stop on front cover V, 50/60 Hz, 750 VA 500 x 50 0x 300 mm, 25 kg 500 x 440 x 230 mm, 19 kg 78 Stanley Gardens, London, W3 7SZ UK T: +44 (0)