Intellivision A/V Mod Installation Guide
|
|
- Thomas Marshall
- 5 years ago
- Views:
Transcription
1 Intellivision A/V Mod Installation Guide This document will guide you through installing your Intellivision A/V Mod Kit to your Intellivision I, II, and III game consoles. Installation is basically the same with varying models. We will show the different 5v source for Intellivision II. Step-by-step guide will show you the detailed instructions; please carefully follow them. Important Note! These old consoles do have large capacitors inside and they need to be discharged before doing any job with the electronics of them. Otherwise, you may get shocked by accidentally or unintentionally touching them. To avoid such a situation, please leave your Intellivision game system s On/Off switch at the ON position for at least 5 minutes with the power plug off the electricity source. Please do not skip this stage! Disclaimer: Though this job is a pretty easy task, it requires that you do some soldering of some wires and connections. If you are not skilled with a soldering iron, please have this installed by someone experienced! I cannot be held responsible for any harm you do to yourself or to your Intellivision game console. Tools Needed Soldering iron, solder, and solder braid X-Acto knife Drill with 1/3 and 1/8 drill bits Needle-nose pliers Philips-head and flat-head screwdrivers Hot glue gun and hot glue stick(optional)
2 Step 1: Open your Intellivision by unscrewing the six screws shown below.
3 Step 2: Again, unscrew the six screws off the platform housing the cables of Intellivision controllers. Follow the arrows for this. Step 3: Carefully unplug the power wires. It is a pity that, years don t behave these systems fairly and such connections may become loose or weak. It s highly recommended that you should really be patient with this stage.
4 Step 4: Now, remove the controllers from the motherboard by simply pulling the plugs away gently and patiently. Using some piece of solder braid, de-solder the RF shielding plates off the motherboard of the system. For Intellivision II and III, you can skip this job as they don t have a shielding around. Step 5: Next, solder the wires to the locations shown below. The wires are labelled on your Intellivision A/V circuit; just match them. 5 volts on the system s motherboard is the first pin of the power flexcable counting from the bottom. Pin 4 or any metal framing the motherboard is your ground ; solder the GND in wire from your A/V circuit here. This kind of flexcables are sensitive to heat; please don t heat them more than needed while soldering on them or nearby. UM RF Modulator has the video and audio legs. Take your V in and A in wires from your A/V circuit and solder them to the legs shown below. Again counting from the bottom, Leg 1 is video and Leg 3 is the audio source.
5 Here is the diagram for Intellivision II. You can solder your GND in wire to any open point at the boundary of the motherboard; and you can pull your 5 volts from the light green trace shown below. Note that IC names can sometimes change as AY into AY or AY and the AM9114s into 2114s. Step 6: Use your needle-nose pliers and bend the piece of metal at the black shielding as shown below. This will be our gate for the wires going to the A/V circuit.
6 Step 7: Now, solder back both of the RF shielding plates and make sure your previously soldered inner wires are not smashed in anyway. Your result for this stage should look something similar to the one below. Step 8: Now, remove the power supply module as shown. It has 2 screws only. Then, pass the remaining wires of the A/V circuit through the canal below the orange cardboard. Also, now is the time to mount your A/V Out connection jacks on your case. Carefully measure the final location and open the two 1/3 holes for the Audio and Video jacks with two 1/8 holes at the sides for the screw set. Use your flat-head screwdriver to turn the screw while holding the nut behind with your needle-nose pliers.
7 Step 9: Solder your GND out wire from the A/V circuit to both of the jacks outer terminals. Your V out wire should be soldered to the center terminal of the yellow jack and A out wire to the center terminal of the white jack. Again, refer to the picture below. Step 10: Plug the power wires coming from the motherboard to the power supply unit in the way you found them at the beginning. Attach your double-sided tape on the back of the circuit and then, to the place shown. Make sure you place the A/V circuit as next to as possible to the screw hole shown on the picture. Otherwise, it may be smashed by the piece of plastic coming over it when the case is closed. Don t forget to clean the place before doing this. You can, optionally, use hot glue here to add strength. Do not let the assembly get over-thick, though.
8 Finalizing... Now, you re set. It s always a good idea to check the functionality before making the thing into one piece. Connect your Intellivision to your Tv via A/V cables and see the improvement over old snowy, wavy, and noisy RF connection. If your mod doesn t work, go back and double-check what you did so far. Also, cleaning the cartridge port and the edges of your game cartridges may help. Sometimes, cartridge ports may get filled with dust and also, game cartridge edges may catch grease or dirt. If your mod works, you should have a nice and clear picture with noise-free sound. Now, you can reassemble your Intellivision. Have Good Gaming Sessions! Please do not hesitate to contact if you have anything to share or a question to ask via m_jonturkk@hotmail.com
3DO Memory Battery Replacement Guide Page 1 of 13. 3DO Memory Battery Replacement Guide
3DO Memory Battery Replacement Guide Page 1 of 13 3DO Memory Battery Replacement Guide Thank you for your purchase of a 3DO memory battery from Nintendo Repair Hut. This guide is designed to help you through
More informationAtari Lynx I Capacitor Replacement Kit Installation Guide Page 1 of 15. Atari Lynx I Capacitor Replacement Kit Installation Guide
Atari Lynx I Capacitor Replacement Kit Installation Guide Page 1 of 15 Atari Lynx I Capacitor Replacement Kit Installation Guide Thank you for your purchase of an Atari Lynx I capacitor replacement kit
More informationInstallation tutorial for Console Customs Xbox ONE MaxFire ONE V2 PCB
Installation tutorial for Console Customs Xbox ONE MaxFire ONE V2 PCB This tutorial is designed to aid you in installation of a console customs MaxFire ONE V2 Circuit board in the newer Xbox One Controllers
More informationWritten By: Jaden Laidig
This guide shows you how to take out the RC Sockets from the Sony BDP-S1. Written By: Jaden Laidig ifixit CC BY-NC-SA www.ifixit.com Page 1 of 6 INTRODUCTION RC sockets are the red and white jacks in the
More informationExplorer Wiring Kit (assembled)
Explorer Wiring Kit (assembled) For Vintage, Firestorm & Standard Series Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers
More informationAssembly Instructions for the 1.5 Watt Amplifier Kit
Assembly Instructions for the 1.5 Watt Amplifier Kit 1.) All of the small parts are attached to a sheet of paper indicating both their value and id. 2.) Leave the parts affixed to the paper until you are
More informationThe IntoPlay build. This section will show how to fill the components into the case halves, and also the case base, which will look like this:
The IntoPlay build Ok, I presume you have read the sections about cutting the holes in the case front, speaker holes and spray painting, modding components, preparing the case, etc. So far, the guides
More informationInstallation tutorial for Console Customs Xbox 360 Dual Rapid fire Microchip for wired and wireless controllers (all versions)
Installation tutorial for Console Customs Xbox 360 Dual Rapid fire Microchip for wired and wireless controllers (all versions) This tutorial is designed to aid you in installation of a console customs
More informationTelecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering tips: Removing Current Wiring: Step 1. Step 2.
Telecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers Wire Strippers 3/8 Drill Bit 5/32 Drill Bit
More informationiphone 6 Chargeport REPAIR GUIDE Version Edition
iphone 6 Chargeport REPAIR GUIDE Version 1 2016 Edition IPHONE 6 CHARGEPORT REPAIR GUIDE LCD AND DIGITIZER REPLACEMENT RiAna Soto Repair Training Specialist rsoto@cellairis.com FOR EVERY REPAIR MAKE SURE
More information66 Dodge Charger (and others) Tach board
66 Dodge Charger (and others) Tach board Introduction: This board replaces the original tachometer driver board in the 66 charger and other cars that use electronics external to the tachometer. The board
More informationManual Version July 2007
Manual Version 1.2 - July 2007 Page 1 Table of Contents Section1: M3 Phono Board Build...3 Phono Board Parts List...3 Preparation...4 Fitting the Valve Bases...6 Installing the Resistors...7 Starting the
More informationModification of USB Sound Card for Asterisk app_rpt Use
Modification of USB Sound Card for Asterisk app_rpt Use First off a huge thank you to Steve for providing the original notes on how to modify a USB sound card. (http://images.qrvc.com/usbfob.pdf) These
More informationUnder Seat Storage Drawer Installation Instructions
Under Seat Storage Drawer Installation Instructions Parts List: 1) Drawer Assembly 8) Self Tapping Screws 1) Instructions 1) Template Tools Needed: Drill and/or Bit Driver Tape Measure Jigsaw or metal
More informationQUAVERATO MIDI MOD. Assembly Instructions
QUAVERATO MIDI MOD Assembly Instructions 110118 QUAVERATO MIDI MOD Assembly Instructions WHAT YOU WILL NEED...3 WHAT S IN THE BOX...4 POPULATING THE PRINTED CIRCUIT BOARD...7 THE CHASSIS...13 UPDATING
More informationCongratulations on purchasing the Spirit Rails Magnetic Attach that allows easy wand to pack removal and reattachment by just getting close!
Introduction Congratulations on purchasing the Spirit Rails Magnetic Attach that allows easy wand to pack removal and reattachment by just getting close! The Spirit Rails Magnetic Attach Kit is designed
More informationLP-200 Dummy Load / Wattmeter
LP-200 Dummy Load / Wattmeter Enclosure Retrofit Assembly Instructions March 2009 TelePost Incorporated LP-200 is a trademark of TelePost Inc. Material in this document copyrighted 2009 TelePost Inc. 1
More informationthe radio grounds switched
Clansman PRC 351 Modification to operatee radio on 10m band Introduction The Clansman PRC 351 is a man portable radio with a maximum output power of approx. 4W and an operating frequency range of 30.000MHz
More informationIphone 5 Glass/Lcd REPAIR GUIDE. Version Edition
Iphone 5 Glass/Lcd REPAIR GUIDE Version 1 2016 Edition IPhone 5 Glass/LCd REPAIR GUIDE RiAna Soto Repair Training Specialist rsoto@cellairis.com FOR EVERY REPAIR MAKE SURE TO COMPLETE, INITIAL, AND HAVE
More informationNever power this piano with anything other than a standard 9V battery!
Welcome to the exciting world of Digital Electronics! Who is this kit intended for? This kit is intended for anyone from ages 13 and above and assumes no previous knowledge in the field of hobby electronics.
More informationAUDI A8 D3 REPLACING THE OUTSIDE DRIVER DOOR HANDLE
AUDI A8 D3 REPLACING THE OUTSIDE DRIVER DOOR HANDLE The keyless entry system in the D3 is a great feature. If you have the car key fob in your pocket, putting your hand under the door handle will unlock
More informationInstallation tutorial for Console Customs PS3 TrueFire Standard Rapid fire Microchip for Sixaxis and Dualshock 3 controllers
Installation tutorial for Console Customs PS3 TrueFire Standard Rapid fire Microchip for Sixaxis and Dualshock 3 controllers This tutorial is designed to aid you in installation of a console customs rapid
More informationAssembly Instructions
Assembly Instructions For the SSQ-2F 3.1 MHz Rife Controller Board Kit v1.41 Manual v1.00 2012 by Ralph Hartwell Spectrotek Services GENERAL ASSEMBLY INSTRUCTIONS Arrange for a clean work surface with
More informationINSTALLATION INSTRUCTIONS
XMOD 23 Mode Rapid Fire Mod Chip INSTALLATION INSTRUCTIONS This tutorial is designed to aid you in the installation of a XMOD Rapid Fire microchip. This installation requires soldering several wires to
More informationInstallation tutorial for Console Customs Xbox Mode Dual Button (RFX-5B) Rapid fire Microchip for all Wired and Wireless controllers
Installation tutorial for Console Customs Xbox 360 5-Mode Dual Button (RFX-5B) Rapid fire Microchip for all Wired and Wireless controllers This tutorial is designed to aid you in installation of a console
More informationBL-ER-P Ethernet Radio Unit for Pedestal Installation Guide
Assemble the Antenna Riser 1. Remove the antenna riser assembly and the antenna from its packaging. 2. Remove the plastic cap, the nut, and the lock washer from the stem of the antenna. 3. Put the stem
More informationGT3B Hack Kit Install Instructions Written By Austin Hutchison
GT3B Hack Kit Install Instructions Written By Austin Hutchison Step 1: Remove 4 screws located on top of the radio. 1 Step 2: There are small plastic latches that also hold the top in place. The easiest
More informationThe Centimani Servo Power Board
The Centimani Servo Power Board Email: srlm@srlmproductions.com Abstract This document discusses the procedure required to build a Centimani Servo Power Board and the capabilities of the board. This board
More informationInstallation tutorial for Console Customs Xbox 360 MaxFire LITE rapid fire Mod Chip.
Installation tutorial for Console Customs Xbox 360 MaxFire LITE rapid fire Mod Chip. This tutorial is designed to aid you in installation of a console customs MaxFire LITE modchip. This tutorial covers
More informationRepairing MagSafe Connector
Repairing MagSafe Connector Written By: Dave Fixedit ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION Magsafe cables are known to break off close to the connector. This article explains how
More informationINSTRUCTION MANUAL. Force Transducer Output Tube Repair Kit
INSTRUCTION MANUAL Model 400-TR Force Transducer Output Tube Repair Kit June 4, 2004, Revision 5 Copyright 2004 Aurora Scientific Inc. Aurora Scientific Inc. 360 Industrial Pkwy. S., Unit 4 Aurora, Ontario,
More informationPowerbook G3 Lombard (1999) USB Repair Manual
Powerbook G3 Lombard (1999) USB Repair Manual Copyright 2003 Powerbookmedic.com. All rights reserved. Any portion of this manual may not be copied, reproduced, or distributed without the express written
More informationSega CD 2 CMOS Battery Replacement Guide Page 1 of 7. Sega CD 2 CMOS Battery Replacement Guide
Sega CD 2 CMOS Battery Replacement Guide Page 1 of 7 Sega CD 2 CMOS Battery Replacement Guide Thank you for your purchase of a Sega CD 2 CMOS battery replacement kit from Nintendo Repair Hut. We appreciate
More informationEA6500 Antenna Installation Instructions:
Thank you for purchasing the 6 Antenna Mod Kit for your Linksys router. First we will show you how to install the antennas for your router. Next we will teach you how to setup the DD-WRT firmware which
More informationInstructions for Lighting an S Scale Caboose
Instructions for Lighting an S Scale Caboose The S Scale Caboose lighting kit is adaptable for most caboose models of rolling stock including American Flyer (TM) and contains the same components as found
More informationAssembly Instructions: Kit #5
Assembly Instructions: Kit #5 1. Insert the T-pin into one of the caps. 2. Insert the rotor core into the same cap as shown below. Apply some pressure to push the rotor core approximately 1/2" (10-12 mm)
More informationLDB-1 Kit Instructions Page 1 of 8
LDB-1 Kit Instructions Page 1 of 8 Important Information Congratulations and thank you for your purchase of the LDB-1 Little Drummer Boy Analog Drum Machine Kit! Before you start, please read the enclosed
More informationPRO 400 M401 MFP M425 CF-280A/X TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
HP PRO 400 M401 MFP M425 CF-280A/X TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS HP CF-280A/X TONER CARTRIDGE REMANUFACTURING THE HP LASERJET PRO 400 M401/MFP M425 (CF-280A/X) TONER CARTRIDGE By Mike Josiah
More informationStandard Kit #1 (3-way switch)
Standard Kit #1 (3-way switch) Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers 3/8 Drill Bit 1/4 Drill Bit Variable
More informationE2500 Antenna Installation Instructions:
Thank you for purchasing the Antenna Mod Kit for your Linksys router. First we will show you how to install the antennas for your router. We will also provide you with a tool that will help test the performance
More informationMacBook Power Cord 5-Pin MagSafe Connector and Cable Replacement
MacBook Power Cord 5-Pin MagSafe Connector and Cable Replacement If the cord connecting the power brick to your MacBook is damaged, use this guide to replace it. Written By: Pierre Merineau ifixit CC BY-NC-SA
More informationThe build should take around 2 to 3 hours. However, by leaving yourself more time you can go at a relaxed pace and be sure not to miss anything.
Before We Start Before we jump into building your Picade, make sure you have everything to hand. I know you're eager to jump right into the construction, but we need to get set up properly first! 1. Prepare
More informationOpen Air. Kit includes: Drawer Full Indicator board assembly, (2) retainers, and (4) screws. PREPARATION
Open Air Installation Video You will need: 8-inch #2 Phillips screwdriver Needle-nose pliers DFI INSTALLATION GUIDE For installation videos, visit the Customer Service playlist at www.youtube.com/user/thelitterrobot
More informationTeam Xecuter Joycon Mod By: XxWiReDxX
Team Xecuter Joycon Mod By: XxWiReDxX Works With Every Switch SX OS Works with every Nintendo Switch and every firmware version! Play Every Game With SX OS you can play all your favorite games straight
More informationBuilding the Toothpick Audio CW Filter
Building the Toothpick Audio CW Filter Introduction The toothpick is a simple variable bandpass audio filter designed to compliment the Splinter QRPp Trans-Receiver. The filter also contains an audio amplifier
More informationRepairing Microsoft Wedge Touch Mouse Battery Cover Retaining Clip
Repairing Microsoft Wedge Touch Mouse Battery Cover Retaining Clip Disassembly, repair and reassembly of Wedge Touch mouse when the battery cover will not stay closed. Also is a good guide to repair other
More informationARP AVATAR PATCH PANEL INSTALLATION MANUAL
ARP AVATAR PATCH PANEL INSTALLATION MANUAL Introduction Thank you for purchasing an Avatar Patch Panel Kit! These instructions are intended to guide you through installing and using this kit. Before we
More informationCircuit Board Assembly Instructions for Babuinobot 1.0
Circuit Board Assembly Instructions for Babuinobot 1.0 Brett Nelson January 2010 1 Features Sensor4 input Sensor3 input Sensor2 input 5v power bus Sensor1 input Do not exceed 5v Ground power bus Programming
More informationPaco Motorsports Strong Arms X
Paco Motorsports Strong Arms 13-101X Thanks for purchasing our Strong Arms. These braces reinforce the frame horns that support the engine and transfer all of the cornering and road impact loads into the
More informationInstalling Your New Creature From The Black Lagoon Tail Light DMD Panel MOD
Installing Your New Creature From The Black Lagoon Tail Light DMD Panel MOD A few things before we start: The wooden speaker panel provided in this MOD was manufactured using a Precision CNC machine and
More informationHP Envy M6-1205DX Screen Replacement
HP Envy M6-1205DX Screen Replacement This guide will show you how to replace your computer's screen. Written By: Alex Wasilewski ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION We will be showing
More informationInstructions to Convert a 4-foot Florescent Fixture to LEDs Using 60W Power Supply Using 2 or 3 strips 30Dec15
Instructions to Convert a 4-foot Florescent Fixture to LEDs Using 60W Power Supply Using 2 or 3 strips 30Dec15 Thank you for purchasing the Shoplight Solutions 4-ft conversion kit. This is a companion
More informationWritten By: Chad Facciolo
HTC One Mini 2 Charging Port Replacement These instructions will show you how to replace your charging port. Written By: Chad Facciolo ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION The charging
More informationHP COLOR LASERJET 3500
HP COLOR LASERJET 3500 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS HP COLOR LASERJET 3500 TONER CARTRIDGE REMANUFACTURING THE HP 3500 COLOR LASERJET TONER CARTRIDGE By Javier Gonzalez and the Technical
More informationINTERNATIONAL RADIO CORP
I N R A D INTERNATIONAL RADIO CORP 13620 Tyee Road Umpqua, OR 97486 (541) 459-5623 fax (541) 459 5632 E-mail: inrad@rosenet.net www.qth.com/inrad IC-775 ROOFING FILTER INSTALLATION INSTRUCTIONS The IC-775
More informationApplication Note. Athearn RTR AC4400CW Tsunami Digital Sound Decoder Installation Notes
Application Note Overview This application note describes how to install a TSU-AT1000 Digital Sound Decoder into an HO Athearn Ready To Roll AC4400CW. Skill Level 2: The entire installation can be completed
More informationIPad mini REPAIR GUIDE. Version Edition
IPad mini REPAIR GUIDE Version 1 2016 Edition IPad Mini REPAIR GUIDE LCD AND DIGITIZER REPLACEMENT RiAna Soto Repair Training Specialist rsoto@cellairis.com FOR EVERY REPAIR MAKE SURE TO COMPLETE, INITIAL,
More informationSTEP 0 Prepare the Materials.
How to Build a Germanium Fuzz Guitar Effect. This document will guide you to build and test your Germanium Fuzz guitar pedal. With all the materials on hand, it takes around 2-4 hours to build it. Try
More informationInstructions to Convert a 4-foot Florescent Fixture to LEDs Using a SS 25W Power Supply and a 4 LED strip 30Dec15
Instructions to Convert a 4-foot Florescent Fixture to LEDs Using a SS 25W Power Supply and a 4 LED strip 30Dec15 Thank you for purchasing the Shoplight Solutions 4-ft conversion kit. This is a companion
More informationStep 3. Remove the strings from your guitar.
VSTK-1 Vintage Stratocaster Kit Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers Electric Drill 3/16 Drill Bit 11/64
More informationEE43 43/100 Fall Final Project: 1: Audio Amplifier, Part Part II II. Part 2: Audio Amplifier. Lab Guide
EE 3/00 EE FINAL PROJECT PROJECT:AN : AUDIO AUDIO AMPLIFIER AMPLIFIER Part : Audio Amplifier Lab Guide In this lab we re going to extend what you did last time. We re going to use your AC to DC converter
More informationBrewsBySmith.com STC DIY Kit
BrewsBySmith.com STC-1000 + DIY Kit Contact Information: Greg Smith www.brewsbysmith.com greg@boostbysmith.com I. Hardware Included: STC-1000 flashed with latest software (v1.06 currently) (if purchased)
More informationKindle 3 Remote Page Turn Switch Replacement
Kindle 3 Remote Page Turn Switch Replacement How to add a remote (wired) page turning switch to the Kindle 3. Written By: AnotherBrian ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION This guide
More informationPacific Antenna Code Practice Oscillator Kit
Pacific Antenna Code Practice Oscillator Kit This kit is offered to initiate the first time builder in the various techniques of mechanical and electronic kit construction. At the end of the approximately
More informationRepairing your Porsche 928 Central Warning System (CWS) controller
Repairing your Porsche 928 Central Warning System (CWS) controller Disclaimer: This procedure is for a 1984 Porsche 928 S controller. Overview: Under the left foot pedal (dead pedal) of the Porsche 928
More informationModifying a USB sound fob to act as a repeater interface for app_rpt
Modifying a USB sound fob to act as a repeater interface for app_rpt This document explains how to modify a USB sound fob to work as a repeater interface for app_rpt. The following materials and tools
More informationOpenROV. Guide 3 - Electronics. We will now move to the assembly of the electronics that will control the ROV. Written By: OpenROV
OpenROV Guide 3 - Electronics We will now move to the assembly of the electronics that will control the ROV. Written By: OpenROV 2017 openrov.dozuki.com Page 1 of 33 INTRODUCTION We will introduce soldering
More informationTKEY-1. CW touch key. (no electromechanical contacts) Assembly manual. Last update: May 1,
TKEY-1 CW touch key (no electromechanical contacts) Assembly manual Last update: May 1, 2016 ea3gcy@gmail.com Updates and news at: www.qsl.net/ea3gcy Thanks for constructing the TKEY-1A CW touch key Have
More informationInstructions to Convert a 4-foot Florescent Fixture to LEDs Using 100W Power Supply Using 1-4 strips 30Dec15
Instructions to Convert a 4-foot Florescent Fixture to LEDs Using 100W Power Supply Using 1-4 strips 30Dec15 Thank you for purchasing the Shoplight Solutions 100W conversion kit. This is a companion document
More informationPacific Antenna RF Probe assembly
Pacific Antenna RF Probe assembly Parts In the Kit: 1 1/2 x 3 Blue PEX tube 2 5/8 O.D. vinyl caps 2 3/32 dia x 2 brass tube sections 2 Pogo spring contacts 1 4-40 x 7/16 pan head screw 1 4-40 x 1/4 pan
More informationThe Switched Longwire Tuner SLT
The Switched Longwire Tuner SLT Thank you for purchasing the SLT kit from Hendricks QRP Kits. This kit is a very high quality kit that you will find easy to build, yet when you finish, you will have a
More informationTable of Contents. Product Spec cations
Table of Contents Model Specification... 2 Important Safety Instructions... 3 Safety Warning Labels... 5 Before You Start... 6 Assembly... 7 Contacts... 14 Product Spec cations Model Dimensions: 27 W x
More informationXMOD 18 Mode Rapid Fire Mod Chip
XMOD 18 Mode Rapid Fire Mod Chip INSTALLATION INSTRUCTIONS - PCB version 2 This tutorial is designed to aid you in the installation of a Rapid Fire microchip. This installation requires soldering several
More informationCongratulations on your purchase of the SparkFun Arduino ProtoShield Kit!
Congratulations on your purchase of the SparkFun Arduino ProtoShield Kit! Well, now what? The focus of this guide is to aid you in turning that box of parts in front of you into a fully functional prototyping
More informationApplications: Section 1: Getting Started Tools Needed: BEFORE
Installation of KBD Body Kits Porsche GT 3 Look/Style 2 Piece Polyurethane Front Bumper & Lip Applications: Porsche 996: 1999-2001 Porsche Boxster 986: 1997-2004 Page 1 Tools Needed: Philips Head Screwdriver
More informationStratitec S5202A Snap-in Circuit Breaker
Stratitec S5202A Snap-in Circuit Breaker Replacement This guide will show the user how to remove and replace a SS-001 snap in circuit breaker for a surge protector. Written By: rainbentrott ifixit CC BY-NC-SA
More informationMatterHackers. How to Install an E3D v6 HotEnd on a Lulzbot. Upgrade your TAZ with a shiny new E3D hotend. Written By: Ryan Lutz
MatterHackers How to Install an E3D v6 HotEnd on a Lulzbot TAZ 5 Upgrade your TAZ with a shiny new E3D hotend. Written By: Ryan Lutz 2017 matterhackers.dozuki.com Page 1 of 21 INTRODUCTION NOTE: This guide
More informationJK FRONT FENDER FLARE INSTALLATION INSTRUCTIONS
JK FRONT FENDER FLARE INSTALLATION INSTRUCTIONS TOOLS NEEDED 3/16 Allen Wrench 1/2 Socket or wrench 10mm Socket Flat head screwdriver HARDWARE 5/16 x 3/4 button heads (14) 5/16 x 1 button heads (8) 5/16
More informationFan Speed Controller/Accelerator Mods
Fan Speed Controller/Accelerator Mods For the Playstation 3 User Manual www.circuitsurgery.com Description This is a series of small modules designed to be inserted between the fan and the mainboard of
More informationInstallation Guide for 10 inch Davies Craig fan in SW20 Engine Lid.
Installation Guide for 10 inch Davies Craig fan in SW20 Engine Lid. This manual is designed to guide you in installing a Davies Craig thermo fan in the lid of your MR2 to aid in reducing engine and intake
More informationBlack and Decker CD2500 Motor Replacement
Black and Decker CD2500 Motor Replacement The guide shows you how to replace the motor in a Black and Decker CD2500. Written By: Ashley ifixit CC BY-NC-SA www.ifixit.com Page 1 of 9 INTRODUCTION Make sure
More informationHow to add a push power button to your XBOX S-Type controller
26.10.2006 Page 1 of 5 http://synapse.wordpress.com How to add a push power button to your XBOX S-Type controller - By Synapse Required Items - XBOX S-Type controller (Wireless ones won t work) Soldering
More informationClansman PRC 320 Modification to add LSB mode
Introduction Clansman PRC 320 Modification to add LSB mode The PRC 320 is a mobile HF radio covering a frequency range of roughly 2 30MHz. Operating modes are AM, CW and SSB. SSB is actually USB only,
More informationLPF-9B Nine band low pass filter module kit ( meters)
LPF-9B Nine band low pass filter module kit (80-60-40-30-20-17-15-12-10 meters) Assembly manual Last update: March 1, 2018 ea3gcy@gmail.com Most recent updates and news at: www.ea3gcy.com Thanks for constructing
More informationFACTORY CAT TOMCAT CORPORATION
FACTORY CAT RPS TOMCAT CORPORATION Artificial Turf and Carpet Sweeping Install Kit #349-641 & #349-642 1. Detach batteries so that there is no power running through the machine before starting. 2. Start
More informationJason Stull. Physics 498 (Physics of Music) Valve Junior Modification 5/13/2010
Jason Stull Physics 498 (Physics of Music) Valve Junior Modification 5/13/2010 1 Introduction My original idea for a class project was to build a tube guitar amplifier. I have wanted a tube amp for some
More informationPSU for LawMate 500mW Transmitters. Assembly and Operation Manual
PSU for LawMate 500mW Transmitters Assembly and Operation Manual Introduction Thank you for purchasing LawMate 500mW Power Supply. This power supply was specifically designed for the 500mW LawMate transmitter
More informationCricket 80a Assembly Manual v Copyright David Cripe NM0S The 4 State QRP Group
Cricket 80a Assembly Manual v. 1.0 Copyright 2017 David Cripe NM0S The 4 State QRP Group Introduction Thank you for purchasing a CRICKET 80a Transceiver. We hope you will enjoy building it and find it
More informationgently pry up all your door switches.. disconnect them.. same with the mirror control on the drivers side..
How To Recover Door Panels By: Crispy SUPPLY/TOOL LIST NEEDED Dremel with drill cutter attachment (or drill with drill bit) contact cement 1/2 inch self tapping screws Carpet/Headliner spray on glue Phillips
More informationPioneer Elite CLD-97 Digital Noise Reduction (DNR) Auto-off Mod DIY Installation Guide
Pioneer Elite CLD-97 Digital Noise Reduction (DNR) Auto-off Mod DIY Installation Guide Background: The CLD-97 laserdisc player has one of the best video quality outputs of any laserdisc player released.
More informationStandard Kit #1 (5-way switch)
Standard Kit #1 (5-way switch) Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers 3/8 Drill Bit 1/4 Drill Bit Variable
More informationDigital Electronics & Chip Design
Digital Electronics & Chip Design Lab Manual I: The Utility Board 1999 David Harris The objective of this lab is to assemble your utility board. This board, containing LED displays, switches, and a clock,
More informationELECRAFT Application Note
ELECRAFT Application Note Front Panel Microphone Circuit Modification Revision A, November 12, 2008 Copyright 2008, Elecraft, Inc., All Rights Reserved Background Some K3 owners have noted distorted transmit
More informationWritten By: Darren Chan
Sega Dreamcast Controller Port Replacement Written By: Darren Chan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION Replacing the F1 fuse on the controller board of the Sega Dreamcast. Soldering
More informationInstalling and Upgrading Internal Modules in Cisco 1800 Series Routers (Modular)
CHAPTER Installing and Upgrading Internal Modules in Cisco 800 Series Routers (Modular) This chapter describes how to install or upgrade modules that are located internally within the Cisco 800 series
More informationTRUE TECHNICAL SERVICE MANUAL - ALL MODELS. DOORS/DRAWERS/LIDS
DOORS/DRAWERS/LIDS 55 56 NOTES DOORS/DRAWERS/LIDS Swing s 73 74 NOTES INSTALLATION OF A GDM-SWING DOOR Phillips Head Screwdriver (2) - 1/8" Drift Punches (forged) Top Bracket NOTE: It may be necessary
More informationPatton Robotics, LLC.
Patton Robotics LLC Patton Robotics T3 Motherboard Assembly Instructions Version 1.1 Patton Robotics, LLC. 61 Hagan Drive New Hope, PA 18938 Phone: 609-977-5525 Email: pattonrobotics@gmail.com Copyright
More informationMotorola E815 / E816 Disassembly / Assembly Guide. Ver. 1.1 By Chubbs_WA
Motorola E815 / E816 Disassembly / Assembly Guide Ver. 1.1 By Chubbs_WA April 10, 2007 Table of Contents Disassembly Tools needed 3 Disassembly for dummies 4 Just a note 5 Disassembly of keypad housing
More informationQRPGuys Iambic Mini Paddle
QRPGuys Iambic Mini Paddle First, familiarize yourself with the parts and check for all the components. If a part is missing, please contact us and we will send one. You must use qrpguys.parts@gmail.com
More informationBi-Color Signal Mirror Installation Instructions
Bi-Color Signal Mirror Installation Instructions 2005-2009 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0141-0 Rev. A2 (3/30/09), BTV 2007 Muth Mirror Systems, LLC Page 3 of 13PplPage
More information