ATTACHMENT B1. Typical Facility Signage Standards and Guidelines/Sign Types

Transcription

1 TTCHMENT B1 Typical Facility Signage Standards and Guidelines/Sign Types

2 S - TERMINLS/GTE RES Sign Type Index Sign Types

3 INDEX - TERMINLS/GTE RES This chapter provides specific information regarding the wayfinding sign types applicable for use in the Terminals/Gate areas of DFW irport. It contains a general sign family overview of the specific sign types (i.e., the Sign Type Index section), as well as more specific design/layouts/notes/etc for each individual sign type (i.e., the Sign Types section). On the following pages, the Sign Type Index shows simple views of each sign type, as well as listings for each sign type s name, mounting method and basic overall size. Note that the Sign Type Index is intended only as a brief, simple catalog for all of the wayfinding sign types used within the Terminals/Gate areas of DFW, and is organized in numeric order of their sign type identification numbers (i.e., Directional sign type category: 1-DR.01, 1-DR.02, etc; Identification sign type category: 1-ID.01, 1-ID.02, etc; Informational sign type category: 1-IN.01, 1-IN.02, etc). Sign Types - Design Intent Drawings Section Sign Types contains design intent drawings of each specific wayfinding sign type used within the Terminals/Gate areas of DFW irport. Each displays scaled drawings of individual sign types and their basic views (i.e., elevations, plan views, end view, etc), sizing/dimensions, face layouts and general design intent related notes. NOTE: these documents are intended to illustrate design intent, and should only be used as a general guideline. No information contained here should be construed as engineered elements. The designer/fabricator/contractor shall be responsible for all engineering and specifications with regard to structural, electrical, mechanical, foundation and installation. Details and information contained in this document shall not be reproduced, copied or utilized in any way except for the specific project for which they were created without previous written authorization from DFW Planning Department. Mounting Requirements Sign mountings shall support signs for optimum visibility, facilitate illumination where required, be fabricated from commonly available materials, be easily maintained, be engineered to established DFW wayfinding system and engineering requirements, and not obstruct or pose any hazard to pedestrians, vehicles or any other entity. Basic Mounting Types The basic mounting types used within DFW s Terminals/Gate areas are as follows: Ceiling Mount: -- Suspended: Overhead signs located in high ceiling areas mounted with a suspension system mechanically attached to the sign s top most element and at the top of the suspension system, with the overall suspension system/sign attached to an above-ceiling structural support system -- Flush Top: Overhead signs mounted in lower ceiling areas with the sign s top most element flush to the ceiling using a mechanical fastening system attached to an above-ceiling structural support system Wall/Soffit/Fascia Mount: Signs that are located on a vertical architectural fascia (overhead) or wall (overhead or pedestrian eye-level), and mechanically attached to the fascia/wall s internal vertical structure Wall Mount - D/tactile plaques: Signs with tactile features that are mounted to walls, doors or other required elements to meet local/d accessibility requirements and codes for accessible design and use Flag (Blade) Mount: Overhead signs mechanically attached on one vertical edge to internal structural elements of vertical architectural surfaces (i.e., walls, columns, etc) in a flag-like configuration Floor/Ground Mount: Non-moveable signs mechanically attached directly to structural elements of an architectural floor or in-ground structural mounting methods Freestanding (Moveable): Signs that utilize freestanding, non-attached base configurations, typically with wide and weighted footer features (to eliminate accidental tipping over); allow for flexibility in moving a sign as changing location conditions require General Mounting Requirements/Restrictions - Pedestrian Signs ll overhead pedestrian signs shall be mounted at a minimum of 8-0 to a typical maximum of 9-0 above finished floor to the bottom of the lowest element of the sign, unless otherwise indicated D accessibility and code required signage shall be mounted in accordance with all applicable code requirements using the most recent edition of the codes and regulations Whenever there is a conflict between a requirement listed in this document and another authoritative code or standard, the more stringent one shall be applied 3.1 INDEX OVERVIEW 3-1

4 .1 NOTE: Shown for existing sign family reference only; Limit use of 4 message directionals whenever possible Overhead Directional - Fascia Mounted (96 w x 39.5 h).5 Overhead Directional - Fascia Mounted (96 w x 29.5 h) B.3 Overhead Directional - Fascia Mounted (192 w x 33.5 h) C.2 Overhead Directional - Suspended (144 w x 23.5 h) NOTE: Shown for existing sign family reference only; Limit use of 4 message directionals whenever possible.2 Overhead Directional - Suspended (96 w x 39.5 h).6 Overhead Directional - Suspended (96 w x 29.5 h) B.4 Overhead Directional - Suspended (192 w x 23.5 h) C.3 Overhead Directional - Fascia Mounted (144 w x 12.5 h) NOTE: Shown for existing sign family reference only; Limit use of 4 message directionals whenever possible.3 Overhead Directional - Fascia Mounted (96 w x 33.5 h) B.1 Overhead Directional - Fascia Mounted (192 w x 39.5 h) B.5 Overhead Directional - Fascia Mounted (192 w x 23.5 h) - New Recommended Option EXIT to: C.4 Overhead Directional - Fascia Mounted (72 w x 24 h).4 Overhead Directional - Suspended (96 w x 33.5 h) B.2 NOTE: Shown for existing sign family reference only; Limit use of 4 message directionals whenever possible Overhead Directional - Suspended (192 w x 39.5 h) C.1 Overhead Directional - Fascia Mounted (144 w x 23.5 h) 3.1 INDEX TERMINLS/GTE RES 3-2

5 MESSGE WOMEN braille WOMEN Next Toilet at Gate 10 women opening for phone connection opening for phone connection XXX WOMEN XXX X New Phase 2 Layout (Future) Stair D.1 Gate ID Pylon - Freestanding 36 w x 102 h) (NOTE: Not Recommended by LI) F.2 Entry Toilet ID (24 w x 12 h) G.1 Bag Claim ID w/ Existing Layout (44 w x 27.5 h) I.1 Elevator Directory - Wall Mounted (18 w x 24.5 h) SYMBOL X Lower Level Upper Level Ticketing/Check-In ll Gates Bag Claim Passenger Pick-Up Parking: Crosswalk to Levels X-X Ground Transportation: Terminal Link Taxi Pre-rranged Limo Shared Ride Lower Level Parking: Crosswalk to Level X Ground Transportation: Rental Cars Public Transit Express & Remote Shuttles E.1 Secondary ID - Blade Mounted (24.5 w x 22.5 h) F.3 Transition Toilet ID (12 w x 12 h) H.1 Interior Vestibule Directional - Fascia Mounted (288 w x 18 h) I.1b Courtesy Vans Elevator Directory - Wall Mounted (18 w x 27 h) - New Recommended Option H.2 Interior Vestibule Directional - Fascia Mounted (144 w x 18 h) Courtesy Phone Terminal X Gate XXX SYMBOL XXX Fire, Police or mbulance irport Information Paging Traveler s id For On-irport Relay Service Use TDD 911 XXXXX XXXXX XXXXX 911 H.3 Interior Vestibule Directional - Fascia Mounted (216 w x 18 h) I.2 Courtesy Phone - Wall Mounted (14.25 w x h) E.2 Secondary ID - Suspended (24 w x 22.5 h) F.4 Gate Door ID - Fascia Mounted (36 w x 18 h) - New Recommended Option Elevator XX to: Elevator Down to: Ground Transportation Terminal X LL XXX Fire, Police or 911 mbulance irport XXXXX Information SYMBOL H.4 Interior Vestibule Directional - Fascia Mounted (72 w x 31 h) Rental Cars 1 Hotels & Motels 2 Taxi 3 Shared Ride 4 Limousine 5 Terminal Link 6 Express 7 Remote 8 DFW Valet 9 Public Transit 10 I.3 Ground Transportation Phone - Wall Mounted (14.25 w x h) E.3 Tertiary ID - Fascia Mounted (10 w x 10.5 h) 3.1 INDEX TERMINLS/GTE RES 3-3

6 INTERNL.1 DIRECTIONL FSCI MOUNT GENERL DESCRIPTION & USE Overhead Directional GENERL NOTES LIGN 1 PLN VIEW Sheet: '-3 1/ 3'- V1 V1 8'-0" 1" 1" 8'-0" 2'-11" NOTE: This sign type is shown for existing sign family reference only; Limit use of 4 message directionals whenever possible 4 1/ ROTTE RROW ON CENTER DETIL : Face Layout 1'-8" 6'-4" 11" 3'- 2 3/4" 5" 5" 5" 5" 1 LIGN 4" 1 4" 5" 5" 1'-8" 3'-3 1/ 5 8'-0" CL CL V1 4" 4" 4" 4" 2'-11" TEXT CLER-SPCE MX. EDGE - ll final design, engineering & amount/sizing of structural sign support elements, material types/thicknesses, dimensions and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit / finish to be reviewed & approved by DFW Planning Dept. and wayfinding / architecture Design Consultants through prototype reviews prior to final production run / installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and / or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location & sign type. FBRICTION INTENT NOTES SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded alum. and cast alum. components with concealed internal welds; removable sign face and light modules; fabricated alum. support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated alum. sign mounting frame with tapered side end cover panels, attached with alum. pin & clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match, satin finish SIGN FCE: fabricated sign face assembly module constructed of extruded alum. frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated alum. trim piece with closed ends; detachable & mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish MOUNTING: mount to wall structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); paint all exposed surfaces to match, satin finish 8'-10 1/.F.F. typ. (to bottom of trim) 9'-0".F.F. typ. (to bottom of soffit) GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): V1 Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White V3 Skylink Yellow: 3M Enamel Receptive V4 Exit Light Green: 3M Opaque Matte to match PMS 368C 2 ELEVTION 3 END VIEW PINT: Blue: Powder coated to match 3M EC , satin finish Silver: MP paint # MP30136, satin finish 3.2 S DIRECTIONLS 3-4

7 INTERNL.2 DIRECTIONL SUSPENDED GENERL DESCRIPTION & USE Overhead Directional 8'-0" LIGN 4" 1 4" 5" 5" 1'-6" V1 8'-0" 1'-6" 3'- 2 3/4" 5" 5" 5" 5" 4 1/ ROTTE RROW ON CENTER 1 1'-8" CL CL 4" 4" 4" 4" 2'-11" TEXT CLER-SPCE MX. EDGE 1 PLN VIEW DETIL : Face Layout Sheet: 1.04 varies (field verify) 1" 3'-3 1/ 3'- 1'-8" V1 8'-0" NOTE: This sign type is shown for existing sign family reference only; Limit use of 4 message directionals whenever possible 4'-0" C 1" 5 L 5 6'-4" 2'-11" 3'-3 1/ 9 3/8" V1 NOTE: ttached to structural elements above ceiling 8'-10 1/.F.F. typ. (to bottom of trim) GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): V1 Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White V3 Skylink Yellow: 3M Enamel Receptive V4 Exit Light Green: 3M Opaque Matte to match PMS 368C 2 ELEVTION 3 END VIEW 4 ELEVTION (OPPOSITE SIDE) PINT: Blue: Powder coated to match 3M EC , satin finish Silver: MP paint # MP30136, satin finish 3.2 S DIRECTIONLS 3-5

8 V1 8'-0" 2'-8" 2 3/4" 5" 5" 5" 4 1/ ROTTE RROW ON CENTER 1 INTERNL.3 4" 1 4" 5" LIGN 5" 1'-8" 8'-0" CL 4" 4" 4" DIRECTIONL 2'-5" TEXT CLER-SPCE MX. EDGE FSCI MOUNT 1 1 / 11 1 / 1'-5 1 / 1 1 / 8" 1'-0" V4 4" 1'-0" 4" 5" 8"4 1 / 8'-0" EXIT to: GENERL DESCRIPTION & USE Overhead Directional CL V2 4" 4" 6" 2'-6 1 / GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES LIGN 1 PLN VIEW Sheet: '-9 1/ 2'-8" 1" 1'-8" V1 8'-0" 6'-4" 1" 2'-5" LIGN DETIL : Face Layout B Sheet: '-9 1/ 2'-8" 1" 1'-8" V1 8'-0" EXIT to: 6'-4" 1" 2'-5" B DETIL B: lternate Face Layout 2'-9 1/ 5 11" V1 SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded aluminum and cast aluminum components with concealed internal welds; removable sign face and light modules; fabricated aluminum support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated aluminum sign mounting frame with tapered side end cover panels, attached with aluminum pin and clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match, satin finish SIGN FCE: fabricated sign face assembly module constructed of extruded aluminum frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated aluminum trim piece with closed ends; detachable and mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish MOUNTING: mount to wall structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); paint all exposed surfaces to match, satin finish GRPHICS / COLORS / DECORTION NOTES 8'-10 1/.F.F. typ. (to bottom of trim) 9'-0".F.F. typ. (to bottom of soffit) 8'-10 1/.F.F. typ. (to bottom of trim) 9'-0".F.F. typ. (to bottom of soffit) V1 V2 V3 V4 Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): Blue: 3M EC Sapphire Blue White: 3M Opaque Matte White Skylink Yellow: 3M Enamel Receptive Exit Light Green: 3M Opaque Matte to match PMS 368C PINT: Blue: Powder coated to match 3M EC , satin finish Silver: MP paint # MP30136, satin finish 2 ELEVTION 3 ELEVTION w/ LTERNTE LYOUT 4 END VIEW 3.2 S DIRECTIONLS 3-6

9 1 PLN VIEW 1'-6" V1 8'-0" 1'-6" 2'-8" 2 3/4" 5" 5" 5" 4 1/ ROTTE RROW ON CENTER 1 INTERNL DETIL : Face Layout.4 4" 1 4" 5" LIGN 5" 1'-8" 8'-0" CL 4" 4" 4" DIRECTIONL 2'-5" TEXT CLER-SPCE MX. EDGE SUSPENDED 1 1 / 11 1 / 1'-5 1 / 1 1 / B 8" 1'-0" V4 4" 1'-0" 4" 5" EXIT to: GENERL DESCRIPTION & USE Overhead Directional DETIL B: lternate Face Layout 8"4 1 / 8'-0" CL V2 4" 4" 6" 2'-6 1 / GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material t - ll final design, engineering, and amount/sizing of structural sign support - Final elements, engineering, material dimensions, types/thicknesses, materials, dimensions, and fabrication and attachment are the responsibility methods of the Fabricat shall be performed and approved by a licensed engineer to meet or exceed all - Wherever applicable dissimilar local and metals national are codes. in contact, always separate contact surfaces prior to assembl - Final Final engineering, fabrication methods, dimensions, quality materials, and fit/finish and fabrication to be reviewed are the and responsibility approved by DFW irport P - Colors of the Fabricator shown are to for ensure reference the highest only, and quality are subject fit and finish to the for limitations all components of the printing process of the completed product. ll final detailing and specifications to be provided - s by the Fabricator shown within here are their general final approved placeholders fabrication-ready only. See graphic shop drawings. message schedules for sp - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded aluinum and cast aluminum components with concealed internal welds; removable sign face and light modules; fabricated aluminum support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated alum. sign mounting frame with tapered side end cover panels, attached with aluminum pin and clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match satin finish Sheet: 1.04 varies (field verify) 2'-9 1/ 2'-8" 1" 1'-8" V1 8'-0" 4'-0" 6'-4" 1" 2'-5" 2'-9 1/ /8" V1 NOTE: ttached to structural elements above ceiling B Sheet: 1.04 EXIT to: SIGN FCE: fabricated sign face assembly module constructed of extruded alum. frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated alum. trim piece with closed ends; detachable and mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish MOUNTING: mount to hidden above-ceiling structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); 2 diameter aluminum suspension tube supports with 4 diameter 3/16 aluminum escutcheon cover plate at ceiling connection point, paint all exposed surfaces to match, satin finish; attached to sign support frame with weld applied flanges and mechanical fasteners 8'-10 1/.F.F. typ. (to bottom of trim) GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): V1 Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White V3 Skylink Yellow: 3M Enamel Receptive V4 Exit Light Green: 3M Opaque Matte to match PMS 368C 2 ELEVTION 3 END VIEW 4 ELEVTION w/ LTERNTE LYOUT (OPPOSITE SIDE) PINT: Blue: Powder coated to match 3M EC , satin finish Silver: MP paint # MP30136, satin finish 3.2 S DIRECTIONLS 3-7

10 V1 8'-0" INTERNL.5 DIRECTIONL 2'-4" 2 3/4" 2 1/ 5" 5" 5" ROTTE RROW ON CENTER FSCI MOUNT 1 LIGN 4" 1 4" 5" 5" 1'-8" 8'-0" CL 4" 4" 4" GENERL DESCRIPTION & USE Overhead Directional 2'-1" TEXT CLER-SPCE MX. EDGE GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES LIGN 1 PLN VIEW Sheet: '-5 1/ 2'-4" 1" 1'-8" V1 8'-0" 6'-4" 1" 2'-1" DETIL : Face Layout 5 2'-5 1/ 11" V1 SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded aluminum and cast aluminum components with concealed internal welds; removable sign face and light modules; fabricated aluminum support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated aluminum sign mounting frame with tapered side end cover panels, attached with aluminum pin and clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match, satin finish SIGN FCE: fabricated sign face assembly module constructed of extruded aluminum frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated aluminum trim piece with closed ends; detachable and mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish MOUNTING: mount to wall structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); paint all exposed surfaces to match, satin finish 8'-10 1/.F.F. typ. (to bottom of trim) 9'-0".F.F. typ. (to bottom of soffit) GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): V1 Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White V3 Skylink Yellow: 3M Enamel Receptive PINT: Blue: Powder coated to match 3M EC , satin finish 2 ELEVTION 3 END VIEW Silver: MP paint # MP30136, satin finish 3.2 S DIRECTIONLS 3-8

11 LIGN 1 PLN VIEW Sheet: '-3 1/ 3'- V1 V1 8'-0" 8'-0" 1" 1" 1" 1" 8'-0" 16'-0" 16'-0" 8'-0" 2'-11" INTERNL B.1 NOTE: This sign type is shown for existing sign family reference only; Limit use of 4 message directionals whenever possible DIRECTIONL DETIL : Face Layout FSCI MOUNT 1'-8" 6'-4" 6'-4" 1'-8" 11" 3'- 2 3/4" 5" 5" 5" 5" 4 1/ ROTTE RROW ON CENTER 1 LIGN 4" 1 4" 5" 5" 1'-8" 3'-3 1/ 5 8'-0" CL CL V1 4" 4" 4" 4" GENERL DESCRIPTION & USE Overhead Directional 2'-11" TEXT CLER-SPCE MX. EDGE GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded aluminum and cast aluminum components with concealed internal welds; removable sign face and light modules; fabricated aluminum support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated aluminum sign mounting frame with tapered side end cover panels, attached with aluminum pin and clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match, satin finish SIGN FCE: fabricated sign face assembly module constructed of extruded aluminum frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated aluminum trim piece with closed ends; detachable and mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish MOUNTING: mount to wall structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); paint all exposed surfaces to match, satin finish 8'-10 1/.F.F. typ. (to bottom of trim) 9'-0".F.F. typ. (to bottom of soffit) GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): V1 Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White V3 Skylink Yellow: 3M Enamel Receptive PINT: Blue: Powder coated to match 3M EC , satin finish 2 ELEVTION 3 END VIEW Silver: MP paint # MP30136, satin finish 3.2 S DIRECTIONLS 3-9

12 INTERNL B.2 DIRECTIONL SUSPENDED GENERL DESCRIPTION & USE Overhead Directional GENERL NOTES - ll final design, engineering & amount/sizing of structural sign support elements, material types/thicknesses, dimensions and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. 1 PLN VIEW 1'-6" V1 8'-0" 16'-0" 8'-0" 1'-6" 3'- 2 3/4" 5" 5" 5" 5" 4 1/ ROTTE RROW ON CENTER 1 DETIL : Face Layout LIGN 4" 1 4" 5" 5" 1'-8" 8'-0" CL CL 4" 4" 4" 4" 2'-11" TEXT CLER-SPCE MX. EDGE - Final engineering, dimensions, materials and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit / finish to be reviewed & approved by DFW Planning Dept. and wayfinding / architecture Design Consultants through prototype reviews prior to final production run / installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and / or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location & sign type. FBRICTION INTENT NOTES SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded alum. and cast alum. components with concealed internal welds; removable sign face and light modules; fabricated alum. support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated alum. sign mounting frame with tapered side end cover panels, attached with alum. pin & clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match varies (field verify) 3'-3 1/ 3'- 1'-8" 8'-0" 6'-4" V1 16'-0" 4'-0" 4'-0" C 5 L 5 1" 1" 1" 1" 8'-0" 6'-4" 1'-8" 2'-11" NOTE: This sign type is shown for existing sign family reference only; Limit use of 4 message directionals whenever possible 3'-3 1/ 9 3/8" V1 NOTE: ttached to structural elements above ceiling SIGN FCE: fabricated sign face assembly module constructed of extruded alum. frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated alum. trim piece with closed ends; detachable & mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish MOUNTING: mount to hidden above-ceiling structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); 2 dia. alum. suspension tube supports with 4 dia. 3/16 thk alum. escutcheon cover plate at ceiling connection point, paint all exposed surfaces to match, satin finish; attached to sign support frame with weld applied flanges and mechanical fasteners 8'-10 1/.F.F. typ. (to bottom of trim) Sheet: 1.04 GRPHICS / COLORS / DECORTION NOTES V1 Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork rrow(s): use only official DFW wayfinding arrow artwork VINYL (FILM): Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White V3 Skylink Yellow: 3M Enamel Receptive V4 Exit Light Green: 3M Opaque Matte to match PMS 368C 2 ELEVTION 3 END VIEW 4 ELEVTION (OPPOSITE SIDE) PINT: Blue: Powder coated to match 3M EC , satin finish Silver: MP paint # MP30136, satin finish 3.2 S DIRECTIONLS 3-10

13 V1 8'-0" 16'-0" 8'-0" INTERNL B.3 DIRECTIONL 2'-8" 2 3/4" 5" 5" 5" 4 1/ ROTTE RROW ON CENTER FSCI MOUNT 1 4" 1 4" 5" LIGN 5" 1'-8" 8'-0" CL 4" 4" 4" GENERL DESCRIPTION & USE Overhead Directional 2'-5" TEXT CLER-SPCE MX. EDGE GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES LIGN 1 PLN VIEW Sheet: '-9 1/ 2'-8" 1'-8" 6'-4" 16'-0" V1 8'-0" 8'-0" 1" 1" 1" 1" 6'-4" 1'-8" 2'-5" DETIL : Face Layout 2'-9 1/ 5 11" V1 SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded aluminum and cast aluminum components with concealed internal welds; removable sign face and light modules; fabricated aluminum support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated aluminum sign mounting frame with tapered side end cover panels, attached with aluminum pin and clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match, satin finish SIGN FCE: fabricated sign face assembly module constructed of extruded aluminum frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated aluminum trim piece with closed ends; detachable and mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish MOUNTING: mount to wall structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); paint all exposed surfaces to match, satin finish 8'-10 1/.F.F. typ. (to bottom of trim) 9'-0".F.F. typ. (to bottom of soffit) GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): V1 Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White V3 Skylink Yellow: 3M Enamel Receptive V4 Exit Light Green: 3M Opaque Matte to match PMS 368C 2 ELEVTION 3 END VIEW PINT: Blue: Powder coated to match 3M EC , satin finish Silver: MP paint # MP30136, satin finish 3.2 S DIRECTIONLS 3-11

14 INTERNL B.4 DIRECTIONL SUSPENDED GENERL DESCRIPTION & USE Overhead Directional GENERL NOTES - ll final design, engineering & amount/sizing of structural sign support elements, material types/thicknesses, dimensions and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. 1 PLN VIEW 1'-6" V1 8'-0" 16'-0" 8'-0" 1'-6" 1'-10" 2 3/4" 5" 5" 4 3/4" ROTTE RROW ON CENTER 1 DETIL : Face Layout 1'-8" 8'-0" LIGN 4" 1 4" 5" 5" CL 4" 4" 1'-7" TEXT CLER-SPCE MX. EDGE - Final engineering, dimensions, materials and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit / finish to be reviewed & approved by DFW Planning Dept. and wayfinding / architecture Design Consultants through prototype reviews prior to final production run / installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and / or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location & sign type. FBRICTION INTENT NOTES SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded alum. and cast alum. components with concealed internal welds; removable sign face and light modules; fabricated alum. support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated alum. sign mounting frame with tapered side end cover panels, attached with alum. pin & clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match varies (field verify) 1'-1 1'-10" 1'-8" 8'-0" 6'-4" V1 16'-0" 4'-0" 4'-0" 1" 1" 1" 1" 6'-4" 8'-0" 1'-8" 1'-7" 1' /8" V1 NOTE: ttached to structural elements above ceiling SIGN FCE: fabricated sign face assembly module constructed of extruded alum. frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated alum. trim piece with closed ends; detachable & mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish MOUNTING: mount to hidden above-ceiling structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); 2 dia. alum. suspension tube supports with 4 dia. 3/16 thk alum. escutcheon cover plate at ceiling connection point, paint all exposed surfaces to match, satin finish; attached to sign support frame with weld applied flanges and mechanical fasteners 8'-10 1/.F.F. typ. (to bottom of trim) Sheet: 1.04 GRPHICS / COLORS / DECORTION NOTES V1 Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork rrow(s): use only official DFW wayfinding arrow artwork VINYL (FILM): Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White V3 Skylink Yellow: 3M Enamel Receptive PINT: Blue: Powder coated to match 3M EC , satin finish 2 ELEVTION 3 END VIEW 4 ELEVTION (OPPOSITE SIDE) Silver: MP paint # MP30136, satin finish 3.2 S DIRECTIONLS 3-12

15 INTERNL B.5 DIRECTIONL FSCI MOUNT GENERL DESCRIPTION & USE Overhead Directional GENERL NOTES - ll final design, engineering & amount/sizing of structural sign support elements, material types/thicknesses, dimensions and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. V1 8'-0" 16'-0" 8'-0" 1'-10" 2 3/4" 5" 5" 4 3/4" ROTTE RROW ON CENTER 1 1'-8" 8'-0" LIGN 4" 1 4" 5" 5" CL 4" 4" 1'-7" TEXT CLER-SPCE MX. EDGE - Final engineering, dimensions, materials and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit / finish to be reviewed & approved by DFW Planning Dept. and wayfinding / architecture Design Consultants through prototype reviews prior to final production run / installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and / or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location & sign type. FBRICTION INTENT NOTES 1 PLN VIEW DETIL : Face Layout SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded alum. and cast alum. components with concealed internal welds; removable sign face and light modules; fabricated alum. support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated alum. sign mounting frame with tapered side end cover panels, attached with alum. pin & clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match, satin finish LIGN 1'-1 1'-10" 16'-0" V1 8'-0" 8'-0" 1" 1" 1" 1" 1'-8" 6'-4" 6'-4" 1'-8" 1'-7" 1' " V1 SIGN FCE: fabricated sign face assembly module constructed of extruded alum. frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated alum. trim piece with closed ends; detachable & mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish MOUNTING: mount to wall structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); paint all exposed surfaces to match, satin finish Sheet: '-10 1/.F.F. typ. (to bottom of trim) 9'-0".F.F. typ. (to bottom of soffit) GRPHICS / COLORS / DECORTION NOTES V1 Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork rrow(s): use only official DFW wayfinding arrow artwork VINYL (FILM): Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White V3 Skylink Yellow: 3M Enamel Receptive V4 Exit Light Green: 3M Opaque Matte to match PMS 368C 2 ELEVTION 3 END VIEW PINT: Blue: Powder coated to match 3M EC , satin finish Silver: MP paint # MP30136, satin finish 3.2 S DIRECTIONLS 3-13

16 INTERNL C.1 DIRECTIONL FSCI MOUNT GENERL DESCRIPTION & USE Overhead Directional GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. V1 12'-0" 1'-10" 2 3/4" 5" 5" 4 3/4" ROTTE RROW ON CENTER 1 LIGN 4" 1 4" 5" 1'-8" CL 12'-0" 4" 4" 1'-7" - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES LIGN 1 PLN VIEW Sheet: '-1 1'-10" 1'-8" 12'-0" V1 1" 11'-10" 1" 8'-8" 1'-8" 1'-7" DETIL : Face Layout 1' " V1 SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded aluminum and cast aluminum components with concealed internal welds; removable sign face and light modules; fabricated aluminum support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated aluminum sign mounting frame with tapered side end cover panels, attached with aluminum pin and clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match, satin finish SIGN FCE: fabricated sign face assembly module constructed of extruded aluminum frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated aluminum trim piece with closed ends; detachable and mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish MOUNTING: mount to wall structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); paint all exposed surfaces to match, satin finish 8'-10 1/.F.F. typ. (to bottom of trim) 9'-0".F.F. typ. (to bottom of soffit) GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): V1 Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White V3 Skylink Yellow: 3M Enamel Receptive PINT: Blue: Powder coated to match 3M EC , satin finish 2 ELEVTION 3 END VIEW Silver: MP paint # MP30136, satin finish 3.2 S DIRECTIONLS 3-14

17 INTERNL C.2 DIRECTIONL SUSPENDED GENERL DESCRIPTION & USE Overhead Directional GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. 1 PLN VIEW V1 12'-0" 4'-0" 4'-0" 1'-6" 1'-6" 1'-10" 2 3/4" 5" 5" 4 3/4" ROTTE RROW ON CENTER 1 LIGN 4" 1 4" 5" 1'-8" DETIL : Face Layout CL 12'-0" 4" 4" 1'-7" - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded aluinum and cast aluminum components with concealed internal welds; removable sign face and light modules; fabricated aluminum support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated alum. sign mounting frame with tapered side end cover panels, attached with aluminum pin and clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match satin finish varies (field verify) 1'-1 1'-10" V1 12'-0" 4'-0" 4'-0" 1" 1" 8'-8" 1'-7" 1'-1 C 5 L 5 9 3/8" V1 NOTE: ttached to structural elements above ceiling SIGN FCE: fabricated sign face assembly module constructed of extruded aluminum frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated alum. trim piece with closed ends; detachable and mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish MOUNTING: mount to hidden above-ceiling structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); 2 diameter aluminum suspension tube supports with 4 diameter 3/16 aluminum escutcheon cover plate at ceiling connection point, paint all exposed surfaces to match, satin finish; attached to sign support frame with weld applied flanges and mechanical fasteners 8'-10 1/.F.F. typ. (to bottom of trim) Sheet: 1.04 GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): V1 Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White V3 Skylink Yellow: 3M Enamel Receptive PINT: Blue: Powder coated to match 3M EC , satin finish 2 ELEVTION 3 END VIEW 4 ELEVTION (OPPOSITE SIDE) Silver: MP paint # MP30136, satin finish 3.2 S DIRECTIONLS 3-15

18 INTERNL C.3 DIRECTIONL FSCI MOUNT GENERL DESCRIPTION & USE Overhead Directional GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. 3 3/4" 7" 4" 2 3/4" 12'-0" - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. V1 11" 4" 3 1/ 7" - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). 12'-0" ROTTE RROW ON CENTER - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES LIGN 1 PLN VIEW Sheet: '-0 1/ 11" V1 12'-0" 1" 11'-10" 1" 1'-2 1/ 9'-7" 1'-2 1/ 8" DETIL : Face Layout 5 1'-0 1/ 10 1/ V1 SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded aluminum and cast aluminum components with concealed internal welds; removable sign face and light modules; fabricated aluminum support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated aluminum sign mounting frame with tapered side end cover panels, attached with aluminum pin and clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match, satin finish SIGN FCE: fabricated sign face assembly module constructed of extruded aluminum frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated aluminum trim piece with closed ends; detachable and mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish MOUNTING: mount to wall structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); paint all exposed surfaces to match, satin finish GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork rrow(s): use only official DFW wayfinding arrow artwork V1 VINYL (FILM): Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White V3 Skylink Yellow: 3M Enamel Receptive PINT: Blue: Powder coated to match 3M EC , satin finish 2 ELEVTION 3 END VIEW Silver: MP paint # MP30136, satin finish 3.2 S DIRECTIONLS 3-16

19 INTERNL C.4 DIRECTIONL FSCI MOUNT GENERL DESCRIPTION & USE Exit Vestibule Directional - Fascia Mounted GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. V1 V4 6" 3 1 / 6'-0" V2 - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 6'-0" 2'-0" 1" 8 1 / 9" 1" EXIT to: 2 1 / 4 1 / - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES 1 PLN VIEW Sheet: '-0" 1" 1" 1'-10" V1 6'-0" 1" 5'-10" 1" EXIT to: 9" 4" 9" LIGN 1" 1" V2 DETIL : Face Layout Scale: 1/2 = 1-0 2'-0" V2 V1 SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded aluminum and cast aluminum components with concealed internal welds; removable sign face and light modules; fabricated aluminum support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated aluminum sign mounting frame with tapered side end cover panels, attached with aluminum pin and clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match, satin finish SIGN FCE: fabricated sign face assembly module constructed of extruded aluminum frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated aluminum trim piece with closed ends; detachable and mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish MOUNTING: mount to wall structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); paint all exposed surfaces to match, satin finish CENTER SIGN BETWEEN EXIT DOORS varies (field verify) GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): V1 Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White V4 Exit Light Green: 3M Opaque Matte to match PMS 368C NOTE: rchitectural conditions vary per install location; field verify PINT: Blue: Powder coated to match 3M EC , satin finish 2 ELEVTION 3 END VIEW 3.2 S DIRECTIONLS 3-17

20 INTERNL H.1 DIRECTIONL FSCI MOUNT GENERL DESCRIPTION & USE Interior Vestibule Directional - Fascia Mounted GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. V1 6'-0" 6'-0" 6'-0" 6'-0" 24'-0" 1'-6" 4" 4" 4" 4" ROTTE RROW ON CENTER 8" 8" 4" 4" LIGN 1'- 6'-0" TEXT CLER-SPCE MX. EDGE - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES Sheet: PLN VIEW 1" 5'-10" 1" 24'-0" V1 6'-0" 6'-0" 6'-0" 6'-0" DETIL : Face Layout SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded aluminum and cast aluminum components with concealed internal welds; removable sign face and light modules; fabricated aluminum support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated aluminum sign mounting frame with tapered side end cover panels, attached with aluminum pin and clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match, satin finish SIGN FCE: fabricated sign face assembly module constructed of extruded aluminum frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated aluminum trim piece with closed ends; detachable and mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish MOUNTING: mount to wall structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); paint all exposed surfaces to match, satin finish 1'-6" 1'- 1'-6" V1 NOTE: rchitectural conditions vary per install location; field verify varies (field verify) GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): V1 Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White V3 Skylink Yellow: 3M Enamel Receptive PINT: Blue: Powder coated to match 3M EC , satin finish 2 ELEVTION 3 END VIEW 3.2 S DIRECTIONLS 3-18

21 INTERNL H.2 DIRECTIONL FSCI MOUNT GENERL DESCRIPTION & USE Interior Vestibule Directional - Fascia Mounted GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. V1 6'-0" 12'-0" 6'-0" 1'-6" 4" 4" 4" 4" ROTTE RROW ON CENTER 8" 8" 4" 4" LIGN 1'- 6'-0" TEXT CLER-SPCE MX. EDGE - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES 1 PLN VIEW Sheet: '-0" 12'-0" 1" 5'-10" 1" V1 6'-0" DETIL : Face Layout SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded aluminum and cast aluminum components with concealed internal welds; removable sign face and light modules; fabricated aluminum support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated aluminum sign mounting frame with tapered side end cover panels, attached with aluminum pin and clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match, satin finish SIGN FCE: fabricated sign face assembly module constructed of extruded aluminum frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated aluminum trim piece with closed ends; detachable and mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish MOUNTING: mount to wall structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); paint all exposed surfaces to match, satin finish 1'-6" 1'- 1'-6" V1 NOTE: rchitectural conditions vary per install location; field verify varies (field verify) GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): V1 Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White V3 Skylink Yellow: 3M Enamel Receptive PINT: Blue: Powder coated to match 3M EC , satin finish 2 ELEVTION 3 END VIEW 3.2 S DIRECTIONLS 3-19

22 INTERNL H.3 DIRECTIONL FSCI MOUNT GENERL DESCRIPTION & USE Interior Vestibule Directional - Fascia Mounted GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. V1 6'-0" 6'-0" 6'-0" 1'-6" 4" 4" 4" 4" ROTTE RROW ON CENTER 8" 8" 4" 4" LIGN 1'- 6'-0" TEXT CLER-SPCE MX. EDGE - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES 1 PLN VIEW Sheet: '-0" V1 6'-0" 6'-0" 6'-0" 1" 5'-10" 1" DETIL : Face Layout SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded aluminum and cast aluminum components with concealed internal welds; removable sign face and light modules; fabricated aluminum support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated aluminum sign mounting frame with tapered side end cover panels, attached with aluminum pin and clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match, satin finish SIGN FCE: fabricated sign face assembly module constructed of extruded aluminum frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated aluminum trim piece with closed ends; detachable and mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish MOUNTING: mount to wall structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); paint all exposed surfaces to match, satin finish 1'-6" 1'- 1'-6" V1 NOTE: rchitectural conditions vary per install location; field verify varies (field verify) GRPHICS / COLORS / DECORTION NOTES V1 V2 V3 Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork rrow(s): use only official DFW wayfinding arrow artwork VINYL (FILM): Blue: 3M EC Sapphire Blue White: 3M Opaque Matte White Skylink Yellow: 3M Enamel Receptive PINT: Blue: Powder coated to match 3M EC , satin finish 2 ELEVTION 3 END VIEW 3.2 S DIRECTIONLS 3-20

23 INTERNL H.4 DIRECTIONL FSCI MOUNT GENERL DESCRIPTION & USE Elevator Directional - Fascia Mounted GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. LIGN 1 PLN VIEW Sheet: '-7" V1 V1 6'-0" 6'-0" Elevator XX to: Elevator Down to: CENTER SIGN BETWEEN ELEVTORS LIGN 2'-7" 6'-0" 2'-7" Elevator XX to: Elevator Down to: 7 1 / 1'-11 1 / V10 V1 6'-0" 3 1 / DETIL : Face Layout Scale: 1/2 = 1-0 Elevator XX to: 3 1 / 2 1 / LIGN V2 1'-6" 2 1 / 2 1 / 2 1 / V1 - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded aluminum and cast aluminum components with concealed internal welds; removable sign face and light modules; fabricated aluminum support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated aluminum sign mounting frame with tapered side end cover panels, attached with aluminum pin and clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match, satin finish SIGN FCE: fabricated sign face assembly module constructed of extruded aluminum frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated aluminum trim piece with closed ends; detachable and mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish MOUNTING: mount to wall structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); paint all exposed surfaces to match, satin finish field verify field verify GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork V1 VINYL (FILM): Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White NOTE: rchitectural conditions vary per install location; field verify NOTE: rchitectural conditions vary per install location; field verify V10 Light Gray: 3M Opaque Matte to match PMS Cool Gray 1C PINT: Blue: Powder coated to match 3M EC , satin finish 2 ELEVTION - DUL ELEVTOR CONDITION 3 ELEVTION - SINGLE ELEVTOR CONDITION 4 END VIEW 3.2 S DIRECTIONLS 3-21

24 Stair NON-ILLUMINTED I.1 INFORMTIONL WLL MOUNT GENERL DESCRIPTION & USE Elevator Directory - Wall Mounted GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. 1 PLN VIEW 1'-6" 2'-0" 1" 1/ 1 3/4" 5/8" varies per no. messages 1 3/4" 5/8" DETIL : Face Layout Scale: 3/4 = 1-0 1'-6" 1'-0" 5/8" 1 3/4" 1'-0" 5/8" 1" Stair 1 3/4" 1/4" 1" 1 3/4" 5/8" copy width limit - Final engineering, dimensions, materials and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Dept. and wayfinding/architecture Design Consultants through prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN FCE: 3/8 thick aluminum panel; paint all exposed surfaces of sign face to match, satin finish TRIM: fabricated aluminum trim piece; attached to sign face panel with LORD adhesive; paint all exposed surfaces to match, satin finish MOUNTING: mount 2nd surface of sign face to wall with.125 diameter threaded studs, DF tape and silicone as required Sheet: '-6" 1'-0" 2'-0" 1/ 1" V1 2'-0" GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork 5'-0".F.F. V1 rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White V3 Skylink Yellow: 3M Enamel Receptive PINT: Blue: Powder coated to match 3M EC , satin finish 2 ELEVTION 3 END VIEW Silver: MP paint # MP30136, satin finish 3.2 S DIRECTIONLS 3-22

25 Upper Level Ticketing/Check-In ll Gates Bag Claim Passenger Pick-Up Parking: Crosswalk to Levels X-X Ground Transportation: Terminal Link Taxi Pre-rranged Limo Shared Ride Lower Level Parking: Crosswalk to Level X Ground Transportation: Rental Cars Public Transit Express & Remote Shuttles Courtesy Vans 1'-6" NON-ILLUMINTED I.1b INFORMTIONL WLL MOUNT 1'-6" 1" 2'- 3/4" 1" 1/ 1/8" X 3 3 /4" 4 3 /4" Lower Level Upper Level Ticketing/Check-In ll Gates Bag Claim Passenger Pick-Up Parking: Crosswalk to Levels X-X Ground Transportation: Terminal Link Taxi Pre-rranged Limo Shared Ride Lower Level Parking: Crosswalk to Level X Ground Transportation: Rental Cars Public Transit Express & Remote Shuttles Courtesy Vans GENERL DESCRIPTION & USE Elevator Directory - Wall Mounted 3/4" 1 1 / 1/ 1" GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Dept. and wayfinding/architecture Design Consultants through prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN FCE: 3/8 thick aluminum panel; paint all exposed surfaces of sign face to match, satin finish TRIM: fabricated aluminum trim piece; attached to sign face panel with LORD adhesive; paint all exposed surfaces to match, satin finish MOUNTING: mount 2nd surface of sign face to wall with.125 diameter threaded studs, DF tape and silicone as required 1 PLN VIEW DETIL : Face Layout Scale: 3/4 = 1-0 Sheet: '- 1/ 1'-6" 1'-0" X Lower Level 1" V1 2'- GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG style symbol artwork 5'-0".F.F. V1 rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White V3 Skylink Yellow: 3M Enamel Receptive PINT: Blue: Powder coated to match 3M EC , satin finish 2 ELEVTION 3 END VIEW Silver: MP paint # MP30136, satin finish 3.2 S DIRECTIONLS 3-23

26 INTERNL D.1 IDENTIFICTION FREESTNDING 6" 6" GENERL DESCRIPTION and USE Gate ID Pylon - Freestanding 1 ROTTE RROW ON CENTER GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 3'-0" 6" - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Dept. and wayfinding/architecture Design Consultants through prototype reviews prior to final production run/installation processes (see Performance Specifications for details). 11" 8" 3'- 3'-0" 1 1'-6" 10 XXX L2 6" 6" 6" - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN CBINET/FRME: freestanding, fabricated aluminum sign cabinet with extruded copy; paint exposed surfaces of sign cabinet to match super white (matte). Top is painted, not coated. pply vinyl V2 graphic where applicable. 1 PLN VIEW DETIL : Face Layout Scale: 1/2 = 1-0 B DETIL B: Face Layout Scale: 1/2 = 1-0 CENTER TEXT and SYMBOLS TRIM: fabricated alum. trim piece with closed ends; detachable and mounted with keyholes/studs and set screws; paint all exposed surfaces to match, clear coated finish (non-gloss) MOUNTING: anchor to floor with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor) F5 INSET KICK: Stainless steel inset with #4 horizontal brushed finish. EXTRUDED COPY: 1/4 aluminum 6061-T6 using a waterjet machine. cute fillet angles will contain an undercut. Letters/numbers/text are 1/4 extruded from face and are applied to face with clear silicone. 3'-0" Sheet: B Sheet: '-0" 1 8" 1'-6" V1 XXX F5 P5 V3 XXX F5 P '-6" 1'-6" 1'-6" F5 V1 P3 P3 GRPHICS/COLORS/DECORTION NOTES 8'-6" 6'-6" 6" V '-6" 6" 6'-6" 6" P4 V2 6'-6" 6" 11" L2 V1 V2 Typeface: font = Neue Haas Bold Universal Symbols: IG style symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork V1 Blue Vinyl (FILM): 3M Sapphire blue, 3MEC Orange text and stripe: 3M #44 Orange Vinyl 2'-10" 10" 2'-10" 10" V3 Skylink Yellow: 3M Enamel Receptive 2 ELEVTION 3 END VIEW 4 ELEVTION (OPPOSITE SIDE) 5 END VIEW PINT: White: Matthews Super White, matte finish Silver: MP paint # MP30136, clear coated finish (non-gloss) P3 Light Gray: Cool Gray 1c, MP paint #MP07273, matte finish P4 P5 Medium Gray: Matthews formulated paint color to match PMS Cool Gray 4c, matte finish Orange: Ellis paint. Hy-Lux Extreme High Gloss Enamel 340 to match Pantone 166c, matte finish 3.2 S IDENTIFICTION 3-24

27 NON-ILLUMINTED E.1 IDENTIFICTION BLDE MOUNT GENERL DESCRIPTION & USE Secondary ID - Blade Mounted GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. 6" 2'-0" 1'-6" 6" 5" 1/ 1/ 1'-10" 1'-1" 2'-0" 1'-1" SYMBOL - Final engineering, dimensions, materials and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality, and fit/finish to be reviewed and approved by DFW Planning Dept. and wayfinding/architecture Design Consultants through prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. 1 PLN VIEW DETIL : Face Layout FBRICTION INTENT NOTES SIGN CBINET/FRME: Fabricated aluminum cabinet, powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match ; applied vinyl graphics MOUNTING: Fabricated aluminum wall mount bracket with top channel to accept sign cabinet; countersunk screws; mount to wall structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); paint all exposed surfaces with Matthews acrylic polyurethane (MP),, satin finish Sheet: '-0" 6" 1/ 5" 1/ 2'-0" 1'-6" 6" SYMBOL 1'-10" 1/ 1'-10 1/ 2'-0" 1'-10" 1'-9" SYMBOL 1/ V2 8'-10 1/.F.F. typ. (to bottom of trim) GRPHICS / COLORS / DECORTION NOTES Universal Symbols: IG style symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): V2 White: 3M Opaque Matte White PINT: Blue: Powder coated to match 3M EC , satin finish Silver: MP paint # MP30136, satin finish 2 ELEVTION 3 END VIEW 4 ELEVTION (OPPOSITE SIDE) 3.2 S IDENTIFICTION 3-25

28 NON-ILLUMINTED E.2 IDENTIFICTION SUSPENDED GENERL DESCRIPTION & USE Secondary ID - Suspended GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. 6" 1/ 5" 1/ 2'-0" 1'-6" 10" 1'-10" 1'-1" 2'-0" 1'-1" SYMBOL - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality, and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants through prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. 1 PLN VIEW DETIL : Face Layout FBRICTION INTENT NOTES SIGN CBINET: Fabricated aluminum cabinet, powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match ; applied vinyl graphics TRIM:.080 fabricated alum. trim piece with closed ends; detachable and mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish Sheet: '-0" 10" 6" 5" NOTE: ttached to structural elements above ceiling MOUNTING: mount to hidden above-ceiling structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); 1 dia. alum. suspension tube supports with 4 dia. 3/16 thk alum. escutcheon cover plate at ceiling connection point, paint all exposed surfaces with Matthews acrylic polyurethane (MP), satin finish; attached to sign support frame with weld applied flanges and mechanical fasteners 1'-10 1/ 1'-10" SYMBOL V2 1'-10 1/ 1'-10" SYMBOL 1'-6" 8'-10 1/.F.F. typ. (to bottom of trim) GRPHICS / COLORS / DECORTION NOTES Universal Symbols: IG style symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): V2 White: 3M Opaque Matte White PINT: Blue: Powder coated to match 3M EC , satin finish Silver: MP paint # MP30136, satin finish 2 ELEVTION 3 END VIEW 4 ELEVTION (OPPOSITE SIDE) 3.2 S IDENTIFICTION 3-26

29 NON-ILLUMINTED E.3 IDENTIFICTION FSCI MOUNT GENERL DESCRIPTION & USE Tertiary ID - Fascia Mounted GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. 1'-6" 1'-6" 3 1 / 1'-6" SYMBOL MESSGE - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES 1 PLN VIEW DETIL : Face Layout Scale: 1/2 = 1-0 SIGN FCE: 3/8 thick alum. panel; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match, satin finish; applied vinyl graphics TRIM: fabricated alum. trim piece; attached to sign face panel with LORD adhesive; paint all exposed surfaces to match, satin finish MOUNTING: mount 2nd surface of sign face to wall with.125 diameter threaded studs, DF tape and silicone as required Sheet: '-6" 1'-0 1 / 1'-7" 1'-6" 1 3 /4" SYMBOL MESSGE V2 1'-7" 6" 9" 1 3 /4" 2 1 /4" GRPHICS / COLORS / DECORTION NOTES V2 Universal Symbols: IG style symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): White: 3M Opaque Matte White PINT: Blue: Powder coated to match 3M EC , satin finish Silver: MP paint # MP30136, satin finish 2 ELEVTION 3 END VIEW 3.2 S IDENTIFICTION 3-27

30 braille WOMEN women Next Toilet at Gate 10 1'-0" 1"1" 6" 3/4" 3/4" 1" WOMEN braille DETIL : Face Layout Scale: 1/2 = 1-0 ID.29 1'-0" 6" L3 NON-ILLUMINTED 1'-0" B 1" 1" 6" 3/4" 3/4" 1" F.2; F.3 6" 1" WOMEN women DETIL : Face Layout Scale: 1/2 = 1-0 L3 IDENTIFICTION WOMEN Next Toilet at Gate 10 LIGN 2'-0" 1/ WLL 1/ 1/4" 10" C GENERL DESCRIPTION & USE Entry Toilet ID; Transition Toilet ID 6" DETIL C: Face Layout Scale: 1/2 = 1-0 6" GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN FCE: Dibond sign panel attached to aluminum tube frame; powdercoat to match ; applied white V2 - White vinyl graphics FRME: 1 x1 fabricated aluminum frame; paint all exposed to match - Silver MOUNTING: mount 2nd surface of sign face to wall with.125 diameter threaded studs, DF tape and silicone as required SEVERE WETHER PLQUE: locate Severe Weather plaque adjacent to restroom sign F.3 1'-0" 1" 10" 1" 1'-0" WOMEN 1'-0" 1" 10" 1" 2'-0" WOMEN 6" 6" V2 F.2 C Sheet: 1.04 GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium V2 V2 L2 Typeface: font = ClearviewText Bold Sheet: 1.04 B Sheet: '-0".F.F. L3 V1 BRILLE: Grade 2 contracted Braille; must meet all applicable D/TS requirements for tactile signage Universal Symbols: IG style symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White 1 ELEVTION V3 V4 V5 Skylink Yellow: 3M Enamel Receptive Exit Light Green: 3M Opaque Matte to match PMS 368C Black: 3M Opaque Matte Black V6 Safety Red: 3M Opaque Matte to match PMS 485C PINT: Blue: Powder coated to match 3M EC , satin finish Silver: MP paint # MP30136, satin finish P3 Skylink Yellow: MP paint to match PMS 130C, satin finish P4 White: MP paint # MP05317; photopolymer Braille, satin fin. P5 Light Green: MP Paint to match PMS 368C, satin finish 3.2 S IDENTIFICTION 3-28

31 NON-ILLUMINTED F.4 IDENTIFICTION FSCI MOUNT GENERL DESCRIPTION & USE Gate Door ID - Fascia Mounted GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. 3'-0" 9" 3'-0" XXX L2 V2 - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES 1 PLN VIEW DETIL : Face Layout Scale: 1/2 = 1-0 SIGN FCE: 3/8 thick aluminum panel; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match, satin finish; applied vinyl graphics MOUNTING: mount 2nd surface of sign face to wall with.125 diameter threaded studs, DF tape and silicone as required Sheet: '-0" 1'-6" XXX 1'-6" GRPHICS / COLORS / DECORTION NOTES L2 V2 Typeface: font = ClearviewText Bold VINYL (FILM): White: 3M Opaque Matte White= PINT: Blue: Powder coated to match 3M EC , satin finish 2 ELEVTION 3 END VIEW 3.2 S IDENTIFICTION 3-29

32 INTERNL G.1 IDENTIFICTION CEILING MOUNT GENERL DESCRIPTION & USE Bag Claim ID GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. 9" 4'-8" 6" 4'- 10" 2'- 10" 3'-8" XXX L2 1'- 1'- 5 3 /4" X 11" L2 - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES 1 PLN VIEW DETIL : Face Layout FINL IMPLEMENTTION SIGN CBINET/FRME:.080 fabricated aluminum cabinet with internally illuminated push-thru acrylic copy; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match, satin finish MOUNTING: Fabricated.080 aluminum ceiling mount bracket; mount tohidden above-ceiling structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); paint all exposed surfaces with Matthews acrylic polyurethane (MP),, satin finish PUSH-THRU COPY: 1/2 translucent white acrylic mounted with studs and clear silicone Sheet: / 4'-8" 6" 4'- 10" 9" 2'-3 1/ 2'- XXX 2'- 2'- 2'- XXX 3'-8" 4" 8'-10 1/.F.F. typ. (to bottom of trim) GRPHICS / COLORS / DECORTION NOTES L2 Typeface: font = ClearviewText Bold Universal Symbols: IG style symbol artwork PINT: Blue: Powder coated to match 3M EC , satin finish Silver: MP paint # MP30136, satin finish 2 ELEVTION 3 END VIEW 4 ELEVTION (OPPOSITE SIDE) 3.2 S IDENTIFICTION 3-30

33 Terminal X Gate XXX Paging Traveler s id Use TDD 911 XXXXX XXXXX XXXXX 911 opening for phone connection NON-ILLUMINTED I.2 INFORMTIONL WLL MOUNT GENERL DESCRIPTION & USE Courtesy Phone - Wall Mounted GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. 1'-2 1/4" 1" lum. angle frame mech. fastened to wall 1/2 thick MDO backer panel Solid 3mm PVC panel Header panel area Insert area (separate PVC Panel) Cut-out area for phone 3/16 screws with threaded T-nuts at each corner, anchored to MDO backer 2'-4 1/4" 1'-2 1/4" Courtesy Phone Terminal X Gate XXX Fire, Police or mbulance irport Information Paging Traveler s id Text Courtesy Phone For On-irport Relay Service Use TDD 911 XXXXX XXXXX XXXXX XXXXX 911 opening for phone connection 9 1/8" NOTE: Digital graphics for entire sign face provided by DFW - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN FCE: 1 PLN VIEW 2 PERSPECTIVE (EXPLODED VIEW) Scale: NTS 1/8 thick clear non-glare acrylic face panel DETIL : Face Layout Scale: 3/4 = /8" - Face Panel: 1/8 clear non-glare acrylic - Graphic Insert: separate 3mm PVC with printed vinyl overlay graphic - Header: 3mm PVC with applied graphic overlay and burshed alum. film stripe - Spacer: 3mm solid PVC panel - Backing: 1/2 solid MDO board NOTE: cut-out opening for phone location thru all layers FRME: fabricated 1 x 1 x 1/8 alum. angle; paint all exposed surfaces to match, satin finish MOUNTING: mount alum. angle frame to wall with hidden mechanical fasteners as conditions require; mount all sign face layers/components at corners (as shown) into MDO backer panel using 3/16 screws with threaded T-nuts. Sheet: '-2 1/4" 1" 2'-4 1/4" Courtesy Phone Fire, Police or mbulance irport Information For On-irport Relay Service 2'-4 1/4" GRPHICS / COLORS / DECORTION NOTES L2 Typeface: font = ClearviewText Medium Typeface: font = ClearviewText Bold L3 BRILLE: Grade 2 contracted Braille; must meet all applicable D/TS requirements for tactile signage 4'-0" Universal Symbols: IG style symbol artwork V1 rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White 3 ELEVTION 4 END VIEW V3 V4 V5 Skylink Yellow: 3M Enamel Receptive Exit Light Green: 3M Opaque Matte to match PMS 368C Black: 3M Opaque Matte Black V6 Safety Red: 3M Opaque Matte to match PMS 485C PINT: Blue: Powder coated to match 3M EC , satin finish Silver: MP paint # MP30136, satin finish P3 Skylink Yellow: MP paint to match PMS 130C, satin finish P4 White: MP paint # MP05317; photopolymer Braille, satin fin. P5 Light Green: MP Paint to match PMS 368C, satin finish 3.2 S INFORMTIONL 3-31

34 Terminal X Fire, Police or mbulance irport Information LL XXX 911 XXXXX Rental Cars 1 Hotels & Motels 2 Taxi 3 Shared Ride 4 Limousine 5 Terminal Link 6 Express 7 Remote 8 opening for phone DFW Valet 9 connection Public Transit 10 NON-ILLUMINTED I.3 INFORMTIONL WLL MOUNT GENERL DESCRIPTION & USE Ground Transportation Phone - Wall Mounted GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. 1'-2 1/4" 1" lum. angle frame mech. fastened to wall 1/2 thick MDO backer panel Solid 3mm PVC panel Header panel area Insert area (separate PVC Panel) Cut-out area for phone 3/16 screws with threaded T-nuts at each corner, anchored to MDO backer 2'-4 1/4" 1'-2 1/4" Ground Transportation Terminal X LL XXX Fire, Police or 911 mbulance irport XXXXX Information Rental Cars Hotels & Motels Taxi Shared Ride Limousine Terminal Link Express Remote DFW Valet Public Transit opening for phone connection 9 1/8" NOTE: Digital graphics for entire sign face provided by DFW - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN FCE: 1 PLN VIEW 2 PERSPECTIVE (EXPLODED VIEW) Scale: NTS 1/8 thick clear non-glare acrylic face panel DETIL : Face Layout Scale: 3/4 = /8" - Face Panel: 1/8 clear non-glare acrylic - Graphic Insert: separate 3mm PVC with printed vinyl overlay graphic - Header: 3mm PVC with applied graphic overlay and burshed alum. film stripe - Spacer: 3mm solid PVC panel - Backing: 1/2 solid MDO board NOTE: cut-out opening for phone location thru all layers FRME: fabricated 1 x 1 x 1/8 aluminum angle; paint all exposed surfaces to match, satin finish MOUNTING: mount alum. angle frame to wall with hidden mechanical fasteners as conditions require; mount all sign face layers/components at corners (as shown) into MDO backer panel using 3/16 screws with threaded T-nuts. Sheet: '-2 1/4" 1" 2'-4 1/4" Ground Transportation 2'-4 1/4" GRPHICS / COLORS / DECORTION NOTES L2 Typeface: font = ClearviewText Medium Typeface: font = ClearviewText Bold L3 BRILLE: Grade 2 contracted Braille; must meet all applicable D/TS requirements for tactile signage 4'-0" Universal Symbols: IG style symbol artwork V1 rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM): Blue: 3M EC Sapphire Blue V2 White: 3M Opaque Matte White 3 ELEVTION 4 END VIEW V3 V4 V5 Skylink Yellow: 3M Enamel Receptive Exit Light Green: 3M Opaque Matte to match PMS 368C Black: 3M Opaque Matte Black V6 Safety Red: 3M Opaque Matte to match PMS 485C PINT: Blue: Powder coated to match 3M EC , satin finish Silver: MP paint # MP30136, satin finish P3 Skylink Yellow: MP paint to match PMS 130C, satin finish P4 White: MP paint # MP05317; photopolymer Braille, satin fin. P5 Light Green: MP Paint to match PMS 368C, satin finish 3.2 S INFORMTIONL 3-32

35 S - CURBSIDE/GROUND TRNSPORTTION RES Sign Type Index Sign Types

36 INDEX - CURBSIDE/GROUND TRNSPORTTION This chapter provides specific information regarding the wayfinding sign types applicable for use in the Curbside/Ground Transportation areas of DFW. It contains a general sign family overview of the specific sign types (i.e., the Sign Type Index section), as well as more specific design/layouts/notes/etc for each individual sign type (i.e., the Sign Types section). On the following pages, the Sign Type Index shows sample views of each sign type, as well as listings for each sign type s name, mounting method and basic overall size. The Sign Type Index is intended only as a brief, simple catalog for all of the wayfinding sign types used within the Curbside/Ground Transportation areas of DFW, and is organized in numeric order of their sign type identification numbers (i.e. Directional sign type category: 3-DR.01, 3-DR.02, etc; Identification sign type category: 3-ID.01, 3-ID.02, etc; Informational sign type category: 3-IN.01, 3-IN.02, etc). Sign Types - Design Intent Drawings Section 4.2- Sign Types contains *design intent drawings of each specific wayfinding sign type used within the Curbside/Ground Transportation areas of DFW. Each displays scaled drawings of individual sign types and their basic views (i.e., elevations, plan views, end view, etc), sizing/dimensions, face layouts and general design intent related notes. *NOTE: these documents are intended to illustrate design intent, and should only be used as a general guideline. No information contained here should be construed as engineered elements. The designer/fabricator/contractor shall be responsible for all engineering and specifications with regard to structural, electrical, mechanical, foundation and installation. Details and information contained in this document shall not be reproduced, copied or utilized in any way except for the specific project for which they were created without previous written authorization from DFW. Mounting Requirements Sign mountings shall support signs for optimum visibility, facilitate illumination where required, be fabricated from commonly available materials, be easily maintained, be engineered to established DFW wayfinding system and engineering requirements, and not obstruct or pose any hazard to pedestrians, vehicles or any other entity. Basic Mounting Types The basic mounting types used within DFW s Curbside/Ground Transportation areas are as follows: Ceiling Mount: -- Suspended: overhead signs located in high ceiling areas mounted with a suspension system mechanically attached to the sign s top most element and at the top of the suspension system, with the overall suspension system/sign attached to an above-ceiling structural support system -- Flush Top: overhead signs mounted in lower ceiling areas with the sign s top most element flush to the ceiling using a mechanical fastening system attached to an above-ceiling structural support system Canopy Mount: -- Flush Top - overhead signs mounted in curbside areas with the sign s top most element flush to the underside/ceiling of a canopy and attached using a mechanical fastening system Wall/Soffit Mount: signs that are located on a vertical architectural fascia (overhead) or wall (overhead or pedestrian eye-level), and mechanically attached to the fascia/wall s internal vertical structure. Flag (Blade) Mount: overhead signs mechanically attached on one vertical edge to internal structural elements of vertical architectural surfaces (i.e. walls, columns, etc) in a flagged configuration Floor/Ground Mount: non-moveable signs mechanically attached directly to structural elements of an architectural floor or in-ground structural mounting methods Freestanding (Moveable): signs that utilize freestanding, non-attached base configurations, typically with wide and weighted footer features (to eliminate accidental tipping over); allow for flexibility in moving a sign as changing location conditions require Wall Mount - D/tactile plaques: signs with tactile features that are mounted to walls, doors or other required elements to meet local/d accessibility requirements and codes for accessible design and use General Mounting Requirements/Restrictions - Pedestrian Signs ll overhead pedestrian signs shall be mounted at a minimum of 8-0 to a typical maximum of 9-0 above finished floor to the bottom of the lowest element of the sign, unless otherwise indicated D accessibility and code required signage shall be mounted in accordance with all applicable code requirements using the most recent edition of the codes and regulations Whenever there is a conflict between a requirement listed in this document and another authoritative code or standard, the more stringent one shall be applied 4.1 INDEX OVERVIEW 4-1

37 Gates XXX-XXX Gates XXX-XXX Gates XXX-XXX Curbside/Ground Transportation reas - Directionals Plan View Plan View Entry XXX Gates XXX-XXX Security Checkpoint Ticketing Side View Entry XXX DFW Valet Passenger Pick Up/Drop Off Taxi Shared Ride Pre-rranged Limo Entry XXX Security Checkpoint Ticketing irline Name Front View 3-DR.51 Curbside View Side View UL Bollard Directional/Entry ID - Ground Mount (39 w x 72 h) Roadside View 3-ID.01 UL Entry ID - Ceiling Suspended (63 w x 36 h) Plan View Entry LL XXX Entry LL XXX Entry LL XXX Gates XXX-XXX Curbside Check-In Bag Claim XXX-XXX irline Name Smoking rea Relief rea Curbside View Side View Roadside View 3-DR.52 LL Bollard Directional/Entry ID - Ground Mount (48 w x 111 h) 3-ID.02 UL Entry ID - Ceiling Suspended Curbside Check-In (96 w x 16 h) 4.1 INDEX CURBSIDE/GROUND TRNSPORTTION RES 4-2

38 Gates XXX-XXX Terminal DFW Valet Link DFW Valet Taxi Shared Ride Taxi Pre-rranged Shared Limo Ride Smoking rea Relief rea Gates XXX-XXX Smoking rea Gates 8-14 Gates Smoking rea Relief rea LL Curbside Map Gates XXX-XXX DFW Valet Taxi Shared Ride Pre-rranged Limo Terminal Link 8-14 Gates Taxi Valet DFW Smoking rea Relief rea Shared Ride irport & Curbside Maps Gates XXX-XXX Express Parking Remote Parking Courtesy Vans DRT Bus Rail/ TRE Rail Remote Parking Smoking rea Relief rea Pet Relief Curbside/Ground Transportation reas - Identification/Informational EXISTING UL COLUMN Plan View ENTRY LL XX Terminal X Gates XX-XX Elevator to: rranged Pre- Passenger Pre- rranged Pick Up & Drop Limo Off Passenger Pick Up & Drop Off Terminal Pre- rranged Link Limo Limo Left Side Front View Right Side Rear View 3-ID.20 Entry ID at LL Elevator Core (typ.) - Fascia Mount (228 w x 16 h) 3-ID.71 UL Ground Trans. ID - Column Wrap (28 w x 80 h x 28 d) EXISTING LL COLUMN Plan View Terminal X Gates XX-XX Escalator to: Ticketing/Check-In Elevator Use: Entry LL XX ENTRY UL XX Terminal X Gates XX-XX 3-ID.21b Entry ID at LL: variant w/ Elevator/Escalator Trailblazer - Fascia Mount (228 w x 16 h) Rental Cars Employee Shuttle to ll Rental Car Companies Shuttle to Employee Parking Lots ENTRY UL D20 Terminal D Ticketing/Check-In Entry LL XXX Entry LL XXX 3-ID.21c Entry ID: variant used at Terminal D - Fascia Mount (228 w x 16 h) 3-ID.21 Entry ID at UL Doors (typ.) - Fascia Mount (228 w x 16 h) Left Front View Right 3-ID.72 LL Ground Trans. ID - Column Wrap (+/ w x 143 h x +/-34.5 d) 4.1 INDEX CURBSIDE/GROUND TRNSPORTTION RES 4-3

39 1 PLN VIEW 3 1/4" Sheet: '- 2 1/4" 2'-10 1/ 2 1/4" EXISTING CST CONCRETE BOLLRD Center sign on exist. bollard 3'- 2 1/4" 2'-10 1/ 2 1/4" Center sign on exist. bollard NON-ILLUMINTED 8" Layout dims. typ.for all message panels 3 1/ Entry XXX 2 3/4" 2 3/4" X X X X 8 1/ 2 3/4" 4 1/4" 7 1/4" 1" 1" 1" 3 1/4" Two-Line Two-Line DETIL : Face Layout Scale: 1/2 = DR.51 2'-10 1/ DIRECTIONL / ID Ground Mount L2 L2 L2 L2 2'-10" 3/4" 2 3/4" 2 3/4" 1 1/4" 3/4" 4 1/4" 4 1/4" 7 1/4" ROTTE RROWS ON CENTER Panel dims. typ.for all message panels B Sheet: /4" 2 3/4" 1 3/8" B 3'- Upper Level Directional/Entry ID on Existing Bollard Entry XXX Two Line 2 3/4" 1" irline Name DETIL B: Face Layout Scale: 1/2 = /4" 2'-10 1/ 2 1/4" GENERL DESCRIPTION & USE 2'-10 1/ 3 1/ 4" 1" 2 1/4" 4 1/4" 1 1/4" 1 1/4" 1 1/4" 1 1/4" 1 1/4" 3/4" 1 3/8" 3 3/4" 3/8" Gates XXX-XXX 2 3/8" Gates XXX-XXX C L 2 3/8" Gates XXX-XXX 2 3/8" 1/ 4" 3/16" Lower Level 3/4" 1 1/4" 1/ Smoking rea 2 3/8" 1 3/8" Pet Relief C 1 3/8" L 1/ 3/4" 4" 1/ 2 3/4" 2 3/8" 2 3/8" 2 3/8" 1" GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES D/F BOLLRD: Sign Component Series 3 components mount to existing cast concrete bollard; vinyl film and digital print graphics applied to.100 T aluminum face panels; components include: - Sign Component Series 3 Radius Post # Sign Component Series 3 Reveal # Sign Component Series 3 Frameless Body # Sign Component Series 3 Radius Post Cap # Sign Component Series 3 Bleed/Frameless Body Corner ngle #5337 RODWY FCE:.100 T aluminum face panel with digitally printed graphic printed on 3M Satin White cast vinyl film; print with OEM latex ink for printer used; graphic to wrap all edges so that no bare metal is visible, panel finish to be mill finish; thorougly clean aluminum prior to application of vinyl wrap with Dupont Prep-Sol or owner approved equal CURBSIDE FCE:.100 T aluminum face panel with digitally printed graphic printed on 3M Satin White cast vinyl film; print with OEM latex ink for printer used; graphic to wrap all edges so that no bare metal is visible, panel finish to be mill finish; thorougly clean aluminum prior to application of vinyl wrap with Dupont Prep-Sol or owner approved equivalent Entry XXX Entry XXX 6'-0" X X X X DFW Valet Passenger Pick Up/Drop Off Taxi Shared Ride Pre-rranged Limo Vx 6'-0" 6'-0" Security Checkpoint Ticketing irline Name Vx 9'-0" 9'-0" 9'-0" Gates XXX-XXX Gates XXX-XXX Gates XXX-XXX 3'-0" EXISTING CST CONCRETE BOLLRD 3'-0" EXISTING CST CONCRETE BOLLRD 3'-0" EXISTING CST CONCRETE BOLLRD 2 ELEVTION - Terminal Exit View Center sign on exist. bollard Center sign on exist. bollard Center sign on exist. bollard 3 SIDE VIEW 4 ELEVTION - Curbside View GRPHICS / COLORS / DECORTION NOTES L2 Typeface: font = ClearviewText Bold Universal Symbols: use only offical DFW irport symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM) / DIGITL PRINT: Vx Curbside/G.T. Digital Print Colors: See Sheet 2-14 PINT: Blue: Powder coated polyester TGIC #PLS1528PT 4.2 S DIRECTIONLS 4-4

40 REFLECTIVE L2 3-DR.52 4'-0" CENTER TEXT 1" 3 1/4" 1" DIRECTIONL / ID Ground Mount Lower Level Bollard Directional/Entry ID L2 GENERL DESCRIPTION & USE 4'-0" CENTER TEXT GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. 1 PLN VIEW 1'-0" 11" 4'-0" 3'-11" 2 1/ 4 1/ Quantity and configuration of message panels varies per loc. Entry LL XXX typ. typ. 1" Two-Line Smoking rea Pet Relief DETIL : Face Layout Scale: 1/2 = 1-0 3/4" 3/4" 5" 2 3/4" 2 3/4" 5" 3'-0" 3 1/4" typ. 3/4" 3 1/4" typ. 2 3/4" 5 1/8" typ. L2 7 11/16" typ. 1" 1 5/8" typ. 3/4" ht. varies per number of message panels L2 2 1/ 4 1/ 8 1/4" 3 1/ 1'-3 5/8" B Entry LL XXX Gates XXX-XXX Bag Claim XXX-XXX irline Name DETIL B: Face Layout Scale: 1/2 = Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type.. FBRICTION INTENT NOTES D/F BOLLRD: Fabricated aluminum sign cabinet with internal support framing and stainless steel toe-kick; toe-kick to be flush with aluminum panels; top panel to have.5 H x 11 x 47 pyramid cap, permanently attached to top panel; unit mounts over and attaches to 6 x 6 x.5 wall square steel bollards (concrete filled, by others) in each leg; field verify install locations and conditions; welded construction, grind welds smooth on faces and backs, all mating edges to be flush; interior framing = mill finish; all exposed exterior faces to be powder coat polyester TGIC #PLS1528PT (Blue); toe-kick finish to be stainless steel with vertical grain number 4 finish RETROREFLECTIVE GRPHIC: 3M DG3 #4090 White retroreflective vinyl film graphics applied to first surface CURBSIDE DIGITL GRPHIC: 36.5 W x 39 H (max.) digitally printed graphic on exterior grade cast vinyl film 3M Controltac Graphic Film 8620Cv3 or owner approved equal CURBSIDE VINYL GRPHIC: 3M # Matte White vinyl film applied first surface Sheet: '-0" 3'-11" 1'-0" 11" B Sheet: / Entry LL XXX V2.2 Entry LL XXX V2.1 Entry LL XXX Gates XXX-XXX Vx Bag Claim XXX-XXX V2.1 DLLS irline Name 7'-11" Smoking rea Relief rea V2.2 7'-11" 2'- 1'-0" 1'-0" GRPHICS / COLORS / DECORTION NOTES 2 ELEVTION - Terminal Exit View 1'-0" 2'-0" 1'-0" 3 SIDE VIEW 4 ELEVTION - Curbside View L2 Typeface: font = ClearviewText Bold Universal Symbols: use only offical DFW symbol artwork rrow(s): use only official DFW wayfinding arrow artwork VINYL (FILM) / DIGITL PRINT: Vx Curbside/G.T. Digital Print Colors: See Sheet 2-14 V2.1 White: 3M # Matte White V2.2 White (retroreflective): 3M DG White PINT: Blue: Powder coated polyester TGIC #PLS1528PT 4.2 S DIRECTIONLS 4-5

41 INTERNL 3-ID.01 IDENTIFICTION SUSPENDED 5'- GENERL DESCRIPTION & USE Ceiling Suspended Entry ID GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. 1 PLN VIEW 5'- 3'-0" 2 1/ 5 3/8" 5 1/ 3 1/ 2 1/ 3 1/ 2 1/ 3 1/ 3 1/ Entry XXX DETIL : Face Layout - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES D/F ENTRY ID:.063 T fabricated aluminum sign cabinet with replaceable acrylic face panels; internal LED illumination, interior of sign cabinet to be painted matte white; face panels to be Plexiglas #2447 with 3M Sapphire Blue vinyl film applied first surface, graphics are reverse weeded to backlight as white; all exposed surfaces to be finished with powder coat polyester TGIC #PLS1528PT (Blue) Sheet: '- 9 3/4" 9 3/4" NOTE: ttached to structural elements above ceiling Hanger Covers: 2 diameter tube hanger covers to conceal engineered hangers as specified by state licensed structural engineer; electrical feed to also be concealed in hanger covers; provide an escutcheon plate at ceiling junction; paint all exposed surfaces with MP paint to match, satin finish varies (field verify) varies (field verify) 3'-0" 2'-8" Entry XXX Gates XXX-XXX Security Checkpoint Ticketing/Check-In Entry XXX V1 Gates XXX-XXX V1 Security Checkpoint Ticketing/Check-In 5'-0" NOTE: Lower three lines of text justified to curbside edge NOTE: Lower three lines of text justified to curbside edge 9'-0" 3'-0" 9'-0" GRPHICS / COLORS / DECORTION NOTES 2 ELEVTION 3 END VIEW 4 ELEVTION (OPPOSITE SIDE) Typeface: font = ClearviewText Medium Universal Symbols: use only offical DFW irport symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork V1 VINYL (FILM) / DIGITL PRINT: Blue: 3M EC Sapphire Blue PINT: Blue: Powder coated polyester TGIC #PLS1528PT Silver: MP paint # MP30136, satin finish 4.2 S IDENTIFICTION/INFORMTIONL 4-6

42 INTERNL 3-ID.02 IDENTIFICTION SUSPENDED GENERL DESCRIPTION & USE Ceiling Suspended Curbside Check-In ID GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. 1 PLN VIEW 8'-0" 1'-4" 1'-1" 1" DETIL : Face Layout 7" 3 1/ 8'-0" 7'-10" Curbside Check-In - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES D/F ENTRY ID:.063 T fabricated aluminum sign cabinet with replaceable acrylic face panels; internal LED illumination, interior of sign cabinet to be painted matte white; face panels to be Plexiglas #2447 with 3M Sapphire Blue vinyl film applied first surface, graphics are reverse weeded to backlight as white; all exposed surfaces to be finished with powder coat polyester TGIC #PLS1528PT (Blue) Sheet: /4" 9 3/4" NOTE: ttached to structural elements above ceiling Hanger Covers: 2 diameter tube hanger covers to conceal engineered hangers as specified by state licensed structural engineer; electrical feed to also be concealed in hanger covers; provide an escutcheon plate at ceiling junction; paint all exposed surfaces with MP paint to match, satin finish varies (field verify) varies (field verify) 1'-4" 1'-1" Curbside Check-In V1 Curbside Check-In V1 7'-10" 1" 1" 9'-0" 9'-0" 1" 5 1/ 8'-0" 1'-4" GRPHICS / COLORS / DECORTION NOTES 2 ELEVTION 3 END VIEW 4 ELEVTION (OPPOSITE SIDE) V1 Typeface: font = ClearviewText Medium Universal Symbols: use only offical DFW irport symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM) / DIGITL PRINT: Blue: 3M EC Sapphire Blue PINT: Blue: Powder coated polyester TGIC #PLS1528PT Silver: MP paint # MP30136, satin finish 4.2 S IDENTIFICTION/INFORMTIONL 4-7

43 INTERNL 3-ID.20 IDENTIFICTION FSCI MOUNT GENERL DESCRIPTION & USE Entry ID at Lower Level Elevator Core (Typical) GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. 1'-4" 1'-1" 8" 5" 4" 1" 1" 2'-10" 7'-10" 1" 3'-10" 1" 4'-10" 1" CENTER TEXT ENTRY LL XXX Terminal X Gates XXX-XXX Elevator to: DETIL : Face Layout 4" 4" 1/ 3'-7" 4'-2 1/ 7 1/ 11" 4" 5 1/ 4" 3'-0" 8'-0" 4'-0" 5'-0" 5'-0" 25'-0" 3 1/ 2 1/ 4" 2 1/ 4'-10" 1" - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES CBINETS: - SIGN CBINET: two-piece extruded aluminum frame; cabinet has internal hinges at bottom to allow removal of face frame for access to copy panel and LED light module; powdercoat all exposed surfaces to match, satin finish - FCE FRME: hinged at bottom and secured with FHMS at top; translucent white, 3/16 thick acrylic copy panel with first surface applied vinyl; V1 is secured to face frame with.090 thick aluminum retainers inside frame; frame slides forward on hinges and pivots 15 degree maximum to remove - BCK FRME: hinged at bottom to receive face frame; contains LED light module; 1/8 thick aluminum back panel is welded to extruded frame; receives mounting bracket and Z clips for mounting to angled mounting bracket MOUNTING: mount to wall structural elements with connection system as installation location conditions require; provide seal at all exterior wall penetrations (Fabricator to coordinate connection location/type of structural elements with General Contractor) NOTE: Elevation shown is typical example only; elevation varies per level and each unique terminal entrance location s conditions; field verify each location V10 V1 25'-0" Sheet: '-0" 8'-0" 4'-0" 5'-0" 5'-0" 1'-4" ENTRY LL XX Terminal X Gates XXX-XXX Elevator to: 1'-4" 1 ELEVTION (TYPICL) Scale: 1/8 = END VIEW Scale: 1/8 = 1-0 GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: use only offical DFW irport symbol artwork VINYL (FILM) / DIGITL PRINT: V1 Blue: 3M EC Sapphire Blue V10 Light Gray: 3M translucent to match PMS Cool Gray 1C PINT: Blue: Powder coated polyester TGIC #PLS1528PT 4.2 S IDENTIFICTION/INFORMTIONL 4-8

44 1'-4" 1'-1" 8" 5" 4" 1" 1" 2'-10" 7'-10" 1" 7'-10" 1" CENTER TEXT ENTRY LL XXX 3'-0" 4" 4" Terminal 1/ 3'-7" 4'-2 1/ 7 1/ X 11" 8'-0" Gates XXX-XXX 4" 5 1/ Ticketing/Check-In 8'-0" 3 1/ 1'-4" INTERNL 1'-1" 8" 5" 4" 1" Terminal 3-ID.21 4" 4" 7 1/ X 7'-10" IDENTIFICTION 1/ 3'-7" 4'-2 1/ 11" 8'-0" 4" Gates XXX-XXX FSCI MOUNT Escalator to: Ticketing/Check-In Entry ID at Upper or Lower Level Terminal Entrance Doors (Typical) Elevator Use: Entry LL XXX GENERL DESCRIPTION & USE 1" 1" 1" 5'-10" 4'-10" 5" 4" 4'-8" 2 1/ 2 1/ 4" 8" 6'-0" 2 3/4" 2 1/ 5'-0" 4" 8" 8" GENERL NOTES - ll final design, engineering & amount/sizing of structural sign support elements, material types/thicknesses, dimensions and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit / finish to be reviewed & approved by DFW Planning Dept. and wayfinding / architecture Design Consultants thru prototype reviews prior to final production run / installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and / or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location & sign type. FBRICTION INTENT NOTES DETIL : 3-ID.21 Face Layout B DETIL B: 3-ID.21b Face Layout CBINETS: - SIGN CBINET: two-piece extruded aluminum frame; cabinet has internal hinges at bottom to allow removal of face frame for access to copy panel and LED light module; powdercoat all exposed surfaces to match, satin finish 1" 1" 2'-10" 6'-10" 8'-10" 1" - FCE FRME: hinged at bottom and secured with FHMS at top; translucent white, 3/16 thick acrylic copy panel with first surface applied vinyl; V1 is secured to face frame with.090 thick aluminum retainers inside frame; frame slides forward on hinges and pivots 15 degree max. to remove 1'-4" 1'-1" 8" 5" 4" CENTER TEXT ENTRY UL XXX 3'-0" 7" 5" 11" 7" 3 1/ Terminal 7'-0" X Ticketing/Check-In 9'-0" 5 1/ - BCK FRME: hinged at bottom to receive face frame; contains LED light module; 1/8 thick aluminum back panel is welded to extruded frame; receives mounting bracket and Z clips for mounting to angled mounting bracket MOUNTING: mount to wall structural elements with connection system as installation location conditions require; provide seal at all exterior wall penetrations (Fabricator to coordinate connection location/type of structural elements with General Contractor) C DETIL C: 3-ID.21c Face Layout NOTE: Elevation shown is typical example only; elevation varies per level and each unique terminal entrance location s conditions; field verify each location V10 V1 1'-4" Sheet: '-0" 3'-0" 8'-0" 8'-0" ENTRY UL XXX Terminal X Gates XXX-XXX Ticketing/Check-In 1'-4" B Sheet: '-4" 19'-0" 8'-0" 6'-0" 5'-0" Escalator to: Elevator Terminal X Gates XXX-XXX Ticketing/Check-In Use: Entry LL XXX 3-ID.21b Entry ID at LL: variant w/ Elevator/Escalator Trailblazer C Sheet: '-0" 3'-0" 7'-0" 9'-0" GRPHICS / COLORS / DECORTION NOTES 3-ID.21 Entry ID shown at Upper Level Doors (typ.) - Fascia Mount (228 w x 16 h) 1'-4" ENTRY UL XXX 3-ID.21c Terminal X Entry ID: variant used at Terminal D Ticketing/Check-In Typeface: font = ClearviewText Medium Universal Symbols: use only offical DFW symbol artwork rrow(s): use only official DFW wayfinding arrow artwork 1 ELEVTION (TYPICL) Scale: 1/8 = END VIEW Scale: 1/8 = VRINTS (TYPICL) Scale: 1/8 = 1-0 V1 V10 VINYL (FILM) / DIGITL PRINT: Blue: 3M EC Sapphire Blue Light Gray: 3M translucent to match PMS Cool Gray 1C PINT: Blue: Powder coated polyester TGIC #PLS1528PT 4.2 S IDENTIFICTION/INFORMTIONL 4-9

45 NON-ILLUMINTED 1'-1 1'-4" CENTER ID TEXT ON ID SYMBOL 3-ID.71 ID/Informational Column Wrap 2'-4" 1" 8" 8" GENERL DESCRIPTION & USE Upper Level Ground Transportation Column Wrap ID on Existing Canopy 1" 2'-4" 1'-8" 1" 3 3/4" GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 2'-4" EXISTING UL COLUMN 1 PLN VIEW 1'-1 4" 2'-4" 2'-4" 1'-1 4" 2'-4" L2 1'- 1/8" 1'-4" 2 1/4" 2 1/ 1 1/4" 2 1/ 1 1/4" 2 1/ 2 1/ 1" 1/ 1" CL 1 3/4" SYMBOL Ground Trans. ID Name 1 2 1/ Lower Level Smoking rea Pet Relief 1/ DETIL : Face Layout Scale: 1/2 = 1-0 1'-3 3/4" L2 1 3/4" 1 3/4" 1" Quantity of directional messages varies per loc. 6" 8" B SYMBOL 1 SYMBOL 2 Passenger Pick Up & Drop Off DETIL B: Face Layout Scale: 1/2 = /8" 5 1/4" 6 1/4" varies per loc./map content C Smoking reas are located on lower level near X00 & X00 MP RTWORK RE 1" DETIL C: Face Layout Scale: 1/2 = 1-0 1/ 7/8" - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES COLUMN WRP HLF:.125T aluminum, router cut per pattern and break-formed shape; to receive additional welded components and digitally printed graphic wrap; thoroughly clean aluminum prior to application of vinyl wrap with Dupont Prep-Sol or owner approved equal COLUMN WRP GRPHIC: digitally printed graphic on 3M Satin White cast vinyl film; print with OEM latex ink for printer used; graphic to wrap all edges so that no bare metal is visible once halves are assembled; thoroughly clean aluminum prior to application of vinyl wrap with Dupont Prep-Sol or owner approved equal BUMP BR/BRCKET: 2 diameter x.125 wall 6061-T6 aluminum round tube; miter corners, continuous weld, grind and fill smooth as required; number 4 horizontal finish; weld to bump bar bracket with continuous fillet weld, grind and fill smooth as required; bracket to be.5 x T6511 aluminum flat bar, miter corners, continuous weld, grind and fill smooth as required; number 4 horizontal finish; bolt bump bar/bracket to existing facility column with Hilti Kwik Bolt TZ SS 316 as specified by state licensed engineer Sheet: '-4" 1'-1 4" B Sheet: '-4" EXISTING UL CNOPY/COLUMN Sheet: '-4" 1'-1 4" C Sheet: '-4" BSE WRP (if used): 12 guage (.1046 T) 316 stainless stell ; cut per pattern and break-formed wings for attachment points; number 4 finish, grain to run vertically; screws to bump bar brackets with 1/4-20 FHMS; hardware to be 316 or 18-8 stainless steel 6'-8" Gates XXX-XXX Terminal DFW Valet Link DFW Valet Taxi Shared Ride Taxi Pre-rranged Shared Limo Ride Smoking rea Relief rea Vx Vx 6'-8" rranged Pre- Passenger Pre- rranged Pick Up & Drop Limo Off Gates 8-14 Gates Smoking rea Relief rea Vx 6'-8" Passenger Pick Up & Drop Off Gates XXX-XXX DFW Valet Taxi Shared Ride Pre-rranged Limo Terminal Link 8-14 Gates Taxi Valet DFW Relief rea Smoking rea Ride Shared Terminal Pre- rranged Link Limo Limo Vx Vx 6'-8" irport & Curbside Maps Vx varies (+/- 9 1/4"; field verify) 2 LEFT SIDE 1'-9" 1 9/16" 1'-7 3/4" 1'-11" 2'-4" 3 ELEVTION ON EXIST. CNOPY - Curbside View 4 RIGHT SIDE 1'-9" 1 9/16" 5 RER SIDE 1'-11" GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium L2 Typeface: font = ClearviewText Bold Universal Symbols: use only offical DFW irport symbol artwork rrow(s): use only official DFW wayfinding arrow artwork Vx VINYL (FILM) / DIGITL PRINT: Curbside/G.T. Digital Print Colors: See Sheet S IDENTIFICTION/INFORMTIONL 4-10

46 Sheet: 1.04 EXISTING LL COLUMN 1 PLN VIEW +/- 2'-10 1/ (field verify) +/- 2'-10 1/ (field verify) EXISTING LL COLUMN +/- 2'-3 1/4" (field verify) B Sheet: /- 2'-3 1/4" (field verify) EXISTING LL COLUMN NON-ILLUMINTED +/- 2'-10 1/ (field verify) EXISTING LL COLUMN 3-ID.72 4'-4 1/ ID/Informational 5 1/4" 1'-10" 3 1/ 1 3/4" 3 1/ 1 3/4" 3 1/ 1 3/8" 1 3/4" 1 3/4" 1 3/4" 7" 3/4" 1/8" 1 1/4" 1'-0 1/ 1 1/4" 5 1/4" 7" CENTER TEXT & ID SYMBOL HORIZ. ON FCE SYMBOL Ground Trans. ID Name L2 Up to Three Lines of Text 1" 2 1/ Entry LL XXX 2 1/ Gates XXX-XXX 5 1/4" +/- 2'-10 1/ 2'-4" Smoking rea Smoking reas are located near XXX & XXX 1 1/4" 3/4" Column Wrap 1 3/4" 1" 3 3/16" 3/4" L2 2'-4" 9" GENERL DESCRIPTION & USE LL Ground Transportation ID +/-2'-3 1/4" SYMBOL 1 SYMBOL 2 9" 9" GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES COLUMN WRP PNELS:.125T 6061-T5 aluminum, mill finish; panel to receive digital print graphic vinyl film application; thoroughly clean aluminum prior to application of vinyl wrap with Dupont Prep-Sol or owner approved equal; mount panels to column-wrap framing with 3M VHB tape #4959 or owner approved equal; column wrap framing to be 1.5 x 1.5 x T6 aluminum square tube, welded construction, grind welds smooth on faces and backs; field verify each install location; visible portions of frame are to match color of column wrap field color; front framing section to attach to side frames with appropriate mechanical fasteners from the inside of frame into backside of sides at front; all mating edges to be flush; framing section to bolt to existing concrete column with appropriate mechanical fasteners COLUMN WRP GRPHIC: digitally printed graphic on 3M Satin White cast vinyl film; print with OEM latex ink for printer used; graphic to wrap all edges so that no bare metal is visible once halves are assembled; thoroughly clean aluminum prior to application of vinyl wrap with Dupont Prep-Sol or owner approved equal DETIL : Face Layout Scale: 3/8 = 1-0 B DETIL B: Face Layout Scale: 3/8 = 1-0 Rental Cars Employee 11'-11" Vx 11'-11" Vx 11'-11" Vx Shuttle to ll Rental Car Companies Shuttle to Employee Parking Lots Entry LL XXX Gates XXX-XXX Smoking rea LL Curbside Map Entry LL XXX Gates XXX-XXX Express Parking Remote Parking Courtesy Vans DRT Bus Rail/ TRE Rail Remote Parking Smoking rea Relief rea Pet Relief 2'-6" EXISTING WLL EXISTING WLL 2'-6" 2'-6" EXISTING WLL GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium L2 Typeface: font = ClearviewText Bold 2 LEFT SIDE 3 ELEVTION (View from Curb) 4 RIGHT SIDE Universal Symbols: use only offical DFW irport symbol artwork rrow(s): use only official DFW irport wayfinding arrow artwork VINYL (FILM) / DIGITL PRINT: Vx Curbside/G.T. Digital Print Colors: See Sheet S IDENTIFICTION/INFORMTIONL 4-11

47 S - GRGE/PRKING RES Sign Type Index Sign Types

48 INDEX GRGES/PRKING RES This chapter provides specific information regarding the wayfinding sign types applicable for use in the Garage/Parking areas of DFW irport. It contains a general sign family overview of the specific sign types (i.e., the Sign Type Index section), as well as more specific design/layouts/notes/etc for each individual sign type (i.e., the Sign Types section). On the following pages, the Sign Type Index shows simple views of each sign type, as well as listings for each sign type s name, mounting method and basic overall size. The Sign Type Index is intended only as a brief, simple catalog for all of the wayfinding sign types used within the Garage/Parking areas of DFW, and is organized in numeric order of their sign type identification numbers (i.e., Directional sign type category: 5-DR.01, 5-DR.02, etc; Identification sign type category: 5-ID.01, 5-ID.02, etc; Informational sign type category: 5-IN.01, 5-IN.02, etc). Sign Types - Design Intent Drawings Section Sign Types contains design intent drawings of each specific wayfinding sign type used within the Garage/Parking areas of DFW. Each displays scaled drawings of individual sign types and their basic views (i.e., elevations, plan views, end view, etc), sizing/dimensions, face layouts and general design intent related notes. NOTE: these documents are intended to illustrate design intent, and should only be used as a general guideline. No information contained here should be construed as engineered elements. The designer/fabricator/contractor shall be responsible for all engineering and specifications with regard to structural, electrical, mechanical, foundation and installation. Details and information contained in this document shall not be reproduced, copied or utilized in any way except for the specific project for which they were created without previous written authorization from DFW. Mounting Requirements Sign mountings shall support signs for optimum visibility, facilitate illumination where required, be fabricated from commonly available materials, be easily maintained, be engineered to established DFW wayfinding system and engineering requirements, and not obstruct or pose any hazard to pedestrians, vehicles or any other entity. Basic Mounting Types The basic mounting types used within DFW Garage/Parking areas are as follows: Ceiling Mount: -- Suspended: Overhead signs located in high ceiling areas mounted with a suspension system mechanically attached to the sign s top most element and at the top of the suspension system, with the overall suspension system/sign attached to an above-ceiling structural support system -- Flush Top: Overhead signs mounted in lower ceiling areas with the sign s top most element flush to the ceiling using a mechanical fastening system attached to an above-ceiling structural support system Wall/Soffit Mount: Signs that are located on a vertical architectural fascia (overhead) or wall (overhead or pedestrian eye-level), and mechanically attached to the fascia/wall s internal vertical structure Wall Mount - D/tactile plaques: Signs with tactile features that are mounted to walls, doors or other required elements to meet local/d accessibility requirements and codes for accessible design and use Light Pole/Column Wrap - Signs that are mounted to existing light poles or columns with mechanical fastening systems and/or surface applied film Flag (Blade) Mount: Overhead signs mechanically attached on one vertical edge to internal structural elements of vertical architectural surfaces (i.e. walls, columns, etc) in a flagged configuration Floor/Ground Mount: Non-moveable signs mechanically attached directly to structural elements of an architectural floor or in-ground structural mounting methods Freestanding (Moveable): Signs that utilize freestanding, non-attached base configurations, typically with wide and weighted footer features (to eliminate accidental tipping over); allow for flexibility in moving a sign as changing location conditions require General Mounting Restrictions - Pedestrian Signs Overhead signs will always be mounted at a minimum of 7-0 above finished floor to the bottom of the lowest element of the sign, unless otherwise indicated or dictated by minimum garage clearance (varies per garage, field verify prior to final fabrication and installation) D accessibility and code required signage (when used) shall be mounted in accordance with all applicable code requirements using the most recent edition of the codes and regulations Whenever there is a conflict between a requirement listed in this document and another authoritative code or standard, the more stringent one shall be applied General Mounting Restrictions - Vehicular Signs Vehicular wayfinding signs shall always be mounted perpendicular to vehicular traffic flow Overhead and roadside signs: all mounting, lateral positioning/spacing from edge of roadway and clearances must be reviewed and approved by a traffic engineer licensed in the State of Texas prior to fabrication and installation Ground-mounted vehicular signs (if used) must be mounted behind crash barriers, use break-away base mounting systems and/or utilize hingedtop connectors (overhead suspended only) in the event of an accidental vehicular collision and as required by TXDOT Vehicular roadside signs must be mounted with the bottom-most viewable area of the sign at a minimum of 7-0 above finished grade unless otherwise indicated Vehicular signs located in the garage will allow for a minimum of overhead garage clearance (varies per garage, field verify prior to final fabrication and installation) Whenever there is a conflict between a requirement listed in this document and another authoritative code or standard, the more stringent one shall be applied 6.1 INDEX OVERVIEW 6-1

49 Terminal X Terminal X Terminal X Terminal X 3 Terminal X Terminal Terminal X Terminal X X Terminal X X Terminal Terminal X Terminal X Welcome to X Parking Terminal X 5-DR.25 Wall/Beam Mount Garage Section Directional - Exterior Pedestrian Entrances 5-DR.26 Wall/Beam Mount Garage Section Directional w/ Welcome ID and North/Central/South ID - Interior reas near Elevator Cores 5-DR.21 Wall/Beam Mount Terminal Trailblazer Terminal X X Terminal XX Existing Bollard Existing Bollard 5-DR.31 Ceiling Suspended Terminal Trailblazer 5-DR.41 Light Post Mount Terminal Trailblazer X Parking Level X Section XX Roof Levels X Parking X Parking Parking Level4 X RowSection C Exit XX Row Sides X Parking Parking Level4 X Row Exit Non-Row Sides 1 Hour X Parking Valet 5-ID.51 Wall/Column Mount Garage Section ID 5-ID.52 Light Pole Mount Garage Section ID 5-ID.53 Column Wrap 1 Hour Pkg. ID 5-ID.54 Column Wrap Valet Pkg. ID X Terminal Parking Level 1 Parking X Parking Terminal Parking X Parking X Parking X Parking X Parking Terminal Parking Level Level 21 Terminal Parking 5 4 Level 32 1 Terminal Parking 5 Level Terminal Parking Level ID.65a 5-ID.65b 5-ID.65c 5-ID.65d 5-ID.65e 5-ID.65a to 5-ID.65e Wall Mount Elevator Level ID 6.1 INDEX GRGE/PRKING RES: PEDESTRIN 6-2

50 X Parking Sections D-F Levels X-X Sections G-J Sections D-F DFW Valet Sections -C 5-ID.55 Wall Mount Large Pedestrian Garage Entrance ID X Parking Level Levels X-X X Elevators 5-ID.56 Wall Mount Elevator Garage/Level ID 6.1 INDEX GRGE/PRKING RES: PEDESTRIN 6-3

51 0000Valet 0000Valet X Parking $XX per day Gates XXX-XXX Gates XXX-XXX Gates XXX-XXX Levels X-X Valet / 1 Hour Gates XXX-XXX Levels X-X Level X: dditional X Parking Gates XXX-XXX CLERNCE: 8-2 CLERNCE: 8-2 CLERNCE: 8-2 $XX $24 per Day day OPEN CLERNCE: DR.10 Large Fascia Mount Garage Entrance Directional 5-DR.11 Fasica Mount Entry Lane Directionals 5-DR.55 Roadside Garage Entrance Directional UP Levels X-X 1 Hour 0000 Valet 0000 Valet / 1 Hour EXIT 5-DR.03 Ceiling Susp. UP/DOWN trailblazer 5-DR.04 Ceiling Susp. Directional w/ Static and Dynamic message 5-DR.05 Ceiling Susp. Valet Trailblazer 5-DR.06 Ceiling Susp. Space Count Directional 5-DR.07 Ceiling Susp. Directionals w/ 2 messages per direction 5-DR.08 Ceiling Susp. Exit Trailblazer UP Levels X-X 1 Hour 0000 Valet Gates XXX-XXX Valet / 1 Hour 0000 Gates XXX-XXX Level X: dditional EXIT 5-DR.13 Beam/Wall Mnt. UP/DOWN trailblazer 5-DR.14 Beam/Wall Mnt. Directional w/ Static and Dynamic message 5-DR.15 Beam/Wall Mnt. Valet Trailblazer 5-DR.16 Beam/Wall Mnt. Space Count Dir. 5-DR.17 Beam/Wall Mnt. Directionals w/ 2 messages per direction 5-DR.18 Beam/Wall Mnt. Exit Trailblazer DOWN Levels X-X EXIT Use: Level X EXIT 5-ID.01 Ramp Entry ID Graphics EXIT Gates XXX-XXX Level Level Level THIS LEVEL Level DO NOT ENTER Level DR.19 Beam/Wall Mnt. Ramp Entry Directional 5-DR.53 Roadside/Roof Level Exit Trailblazer 5-IN.01 Roadside Level ID/Space Count Informational 5-RG.01 Do Not Enter Graphics 6.1 INDEX GRGE/PRKING RES: VEHICULR 6-4

52 REFLECTIVE 5-DR.03 DIRECTIONL CEILING SUSPENDED GENERL DESCRIPTION & USE VEHICULR - UP/DOWN Trailblazer; 1 direction; 1 or 2 sides GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 10'-0" - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW irport Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). 4 1 / 1'-0" 4" 2'-8" 5 1 / 7" 4" - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. 2 1 / 1 PLN VIEW 10'-0" 1'-6" 1'-0" Rotate arrow on center FCE LYOUT Scale: 1/2 = 1-0 UP S3 V7 V7 L2 V9 V9 V7 L2 V7 Center text vert./horiz. within box (NOTE: ID message may read UP or DOWN depending on sign location) Levels X-X Center text/symbol vert. on arrow 5 1 / - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN CBINET/FRME: modular fabricated internal illuminated edge-lit sign module cabinet constructed of extruded aluinum and cast aluminum components with concealed internal welds; removable sign face and light modules; fabricated aluminum support frame with welded mitered corners and slotted mounting holes to accept sign mounting brackets; fabricated alum. sign mounting frame with tapered side end cover panels, attached with aluminum pin and clip system; power feed/units hidden behind mounting frame with access holes in back for wall mounting; powdercoat all exposed surfaces of sign cabinet/support frame/mounting frame to match satin finish SIGN FCE: fabricated sign face assembly module constructed of extruded aluminum frame and concealed internal welds; faces are 3/16 white acrylic with 1st surface applied V1 vinyl film, graphics reversed out of blue (white is exposed white acrylic cut-thru blue film); faces illuminated with light panel assembly using LED edge-lit clear inscribed acrylic diffuser and self-contained technology (including electronics, extruded frame and diffuser) TRIM:.080 fabricated alum. trim piece with closed ends; detachable and mounted with keyholes/studs and set screws; paint all exposed surfaces to match, satin finish Sheet: '-0" MOUNTING: mount to hidden above-ceiling structural elements with connection system as installation location conditions require (Fabricator to coordinate connection location/type of structural elements with General Contractor); 2 diameter aluminum suspension tube supports with 4 diameter 3/16 aluminum escutcheon cover plate at ceiling connection point, paint all exposed surfaces to match, satin finish; attached to sign support frame with weld applied flanges and mechanical fasteners 9" 9" 1'-6" UP Levels X-X Levels X-X UP field verify 11" varies varies 1'-6" 2 1 / GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium L2 Typeface: font = ClearviewText Bold 2 ELEVTION 3 END VIEW 4 ELEVTION (OPPOSITE SIDE) S3 Universal Symbols: IG/TXDOT style symbol artwork Veh. rrow(s): use only official MUTCD/TXDOT arrow art VINYL (FILM) / DIGITL PRINT: V7 White: 3M 4090 DG3 White (Reflective) V9 Blue: 3M 4095 DG3 Blue (Reflective) PINT: Silver: Matthews Paint #MP30136 Brushed luminum, satin finish 6.2 S DIRECTIONLS 6-5

53 REFLECTIVE / DYNMIED 5-DR.04 DIRECTIONL CEILING SUSPENDED GENERL DESCRIPTION & USE VEHICULR - Directional w/ Static & Dynamic message; 1 direction; 1 or 2 sides GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 4 1 / 1'-0" 4" 7" 4 1 / 7'- 3 1 / match existing - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. TBD 1 PLN VIEW 7'- 1'-6" Rotate arrow on center 1'-0" FCE LYOUT Scale: 1/2 = 1-0 S3 V7 V7 V7 1 Hour 0000 V9 Center text/symbol vert. on arrow 5 1 / 7" - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN BOX: fabricated aluminum extrusion frame with removable aluminum face panels, all welds filled and ground smooth for seamless appearance; removable faces use internal hidden top aluminum panel clip and are mechanically fastened with countersunk S.S. screws at bottom returns eges of extrusion frame (paint screwheads to match returns) into internal aluminum angle; vertical support tubes mechanically fastened to top of sign box extrusion frame; digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels; all exposed surfaces, returns, etc to be painted with MP paint to match, satin finish; routed cut-outs in face panels and vents in sign box sized per dynamic unit required SUPPORT FRME/SUSPENSION: fabricated 2 square aluminum support tube frame and vertical suspension tube structure; all exposed support frame tube ends to be capped with aluminum; all welds on frame/caps to be filled and ground smooth for uniform appearance; suspension tubes mechanically attached to ceiling attachment hinge plates above; ceiling attachment plates to be mechanically fastened to garage s structural ceiling elements as required with mech. fasteners (fabricator to field verify); support frame, suspension tubes and hinge plates to be painted all exposed surfaces with MP paint to match, satin finish DYNMIC SPCE COUNT UNIT: By others Sheet: 0.06 varies 1'-6" 7'- 9" 9" varies 1 Hour Hour 1'-6" TBD field verify GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium 2 ELEVTION 3 END VIEW 4 ELEVTION (OPPOSITE SIDE) S3 Universal Symbols: IG/TXDOT style symbol artwork Veh. rrow(s): use only official MUTCD/TXDOT arrow art VINYL (FILM) / DIGITL PRINT: V7 White: 3M 4090 DG3 White (Reflective) V9 Blue: 3M 4095 DG3 Blue (Reflective) PINT: Silver: Matthews Paint #MP30136 Brushed luminum, satin finish 6.2 S DIRECTIONLS 6-6

54 REFLECTIVE 5-DR.05 DIRECTIONL CEILING SUSPENDED GENERL DESCRIPTION & USE VEHICULR - Valet Trailblazer; 1 direction; 1 or 2 sides GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 4'-8" - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). 4 1 / 1'-0" 4" 7" 3 1 / - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. 1 PLN VIEW 2 1 / 4'-8" 1'-6" 1'-0" Rotate arrow on center FCE LYOUT Scale: 1/2 = 1-0 Valet S3 V7 V7 V9 V7 5 1 / Center text/symbol vert. on arrow - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN FCE PNELS: 1/8 thick aluminum sign face panels; mechanically fasten sign panels to support tube structure with stainless steel countersunk screws, paint heads to match sign face; digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels; all exposed surfaces, returns, etc. to be clearcoated to prevent corrosion SUPPORT FRME/SUSPENSION: fabricated 2 square aluminum support tube frame and vertical suspension tube structure; all exposed support frame tube ends to be capped with aluminum; all welds on frame/caps to be filled and ground smooth for uniform appearance; suspension tubes mechanically attached to ceiling attachment hinge plates above; ceiling attachment plates to be mechanically fastened to garage s structural ceiling elements as required with mech. fasteners (fabricator to field verify); support frame, suspension tubes and hinge plates to be painted all exposed surfaces with MP paint to match, satin finish Sheet: '-8" 9" 9" field verfiy 1'-6" varies Valet 1'-6" varies 2 1 / Valet GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium 2 ELEVTION 3 END VIEW 4 ELEVTION (OPPOSITE SIDE) S3 Universal Symbols: IG/TXDOT style symbol artwork Veh. rrow(s): use only official MUTCD/TXDOT arrow art VINYL (FILM) / DIGITL PRINT: V7 White: 3M 4090 DG3 White (Reflective) V9 Blue: 3M 4095 DG3 Blue (Reflective) PINT: Silver: Matthews Paint #MP30136 Brushed luminum, satin finish 6.2 S DIRECTIONLS 6-7

55 REFLECTIVE / DYNMIED 5-DR.06 DIRECTIONL CEILING SUSPENDED GENERL DESCRIPTION & USE VEHICULR - Space Count Directional; 1 direction; 1 or 2 sides GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 4'-8" - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). 4 1 / 1'-0" 4" 7" 3 1 / match existing - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. 1 PLN VIEW TBD 4'-8" 1'-6" 1'-0" Rotate arrow on center FCE LYOUT Scale: 1/2 = 1-0 S3 V7 V Valet Center text/symbol vert. on arrow V9 - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN BOX: fabricated aluminum extrusion frame with removable aluminum face panels, all welds filled and ground smooth for seamless appearance; removable faces use internal hidden top aluminum panel clip and are mechanically fastened with countersunk S.S. screws at bottom returns eges of extrusion frame (paint screwheads to match returns) into internal aluminum angle; vertical support tubes mechanically fastened to top of sign box extrusion frame; digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels; all exposed surfaces, returns, etc to be painted with MP paint to match, satin finish; routed cut-outs in face panels and vents in sign box sized per dynamic unit required SUPPORT FRME/SUSPENSION: fabricated 2 square aluminum support tube frame and vertical suspension tube structure; all exposed support frame tube ends to be capped with aluminum; all welds on frame/caps to be filled and ground smooth for uniform appearance; suspension tubes mechanically attached to ceiling attachment hinge plates above; ceiling attachment plates to be mechanically fastened to garage s structural ceiling elements as required with mech. fasteners (fabricator to field verify); support frame, suspension tubes and hinge plates to be painted all exposed surfaces with MP paint to match, satin finish DYNMIC SPCE COUNT UNIT: By others Sheet: '-8" 9" 9" field verfiy 1'-6" varies Valet 1'-6" varies 0000 Valet 0000 TBD GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium 2 ELEVTION 3 END VIEW 4 ELEVTION (OPPOSITE SIDE) S3 Universal Symbols: IG/TXDOT style symbol artwork Veh. rrow(s): use only official MUTCD/TXDOT arrow art VINYL (FILM) / DIGITL PRINT: V7 White: 3M 4090 DG3 White (Reflective) V9 Blue: 3M 4095 DG3 Blue (Reflective) PINT: Silver: Matthews Paint #MP30136 Brushed luminum, satin finish 6.2 S DIRECTIONLS 6-8

56 REFLECTIVE / DYNMIED 5-DR.07 DIRECTIONL CEILING SUSPENDED GENERL DESCRIPTION & USE VEHICULR - Directionals w/ 2 messages per direction; 2 directions; 1 or 2 sides GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. 4 1 / 1'-0" 4 1 / 7" 9'-0" - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). 2 1 / 1 PLN VIEW 9'-0" 9'-0" 1'-10" 1'-0" Rotate arrow on center S3 V7 V7 V7 FCE LYOUT Scale: 1/2 = 1-0 Gates XXX-XXX Valet / 1 Hour 0000 Center text/symbol vert. on arrow 3 1 / match existing - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN BOX: fabricated aluminum extrusion frame with removable aluminum face panels, all welds filled and ground smooth for seamless appearance; removable faces use internal hidden top aluminum panel clip and are mechanically fastened with countersunk S.S. screws at bottom returns eges of extrusion frame (paint screwheads to match returns) into internal aluminum angle; vertical support tubes mechanically fastened to top of sign box extrusion frame; digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels; all exposed surfaces, returns, etc to be painted with MP paint to match, satin finish; routed cut-outs in face panels and vents in sign box sized per dynamic unit required SUPPORT FRME/SUSPENSION: fabricated 2 square aluminum support tube frame and vertical suspension tube structure; all exposed support frame tube ends to be capped with aluminum; all welds on frame/caps to be filled and ground smooth for uniform appearance; suspension tubes mechanically attached to ceiling attachment hinge plates above; ceiling attachment plates to be mechanically fastened to garage s structural ceiling elements as required with mech. fasteners (fabricator to field verify); support frame, suspension tubes and hinge plates to be painted all exposed surfaces with MP paint to match, satin finish DYNMIC SPCE COUNT UNIT: By others Sheet: " 9" 9" 9" varies 1'-10" Gates XXX-XXX Valet / 1 Hour 0000 Gates XXX-XXX Level X: dditional varies 1'-10" 0000 Valet / 1 Hour field verify 5" 5" 5" 9'-0" 9'-0" 2 1 / GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium 2 ELEVTION 3 END VIEW 4 ELEVTION (OPPOSITE SIDE) S3 Universal Symbols: IG/TXDOT style symbol artwork Veh. rrow(s): use only official MUTCD/TXDOT arrow art VINYL (FILM) / DIGITL PRINT: V7 White: 3M 4090 DG3 White (Reflective) V9 Blue: 3M 4095 DG3 Blue (Reflective) PINT: Silver: Matthews Paint #MP30136 Brushed luminum, satin finish 6.2 S DIRECTIONLS 6-9

57 REFLECTIVE 5-DR.08 DIRECTIONL CEILING SUSPENDED GENERL DESCRIPTION & USE VEHICULR - Exit Trailblazer; 1 direction; 1 or 2 sides GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. 1 PLN VIEW 2 1 / 5'-0" 1'-6" 1/ 1'-0" 1/ Rotate arrow on center FCE LYOUT Scale: 1/2 = 1-0 5'-0" 1/ 3 1 / 1'-0" 4" 10 1 / 4" 1/ S3 V7 V7 V9 V7 D3 D2 EXIT 7" Center text/symbol vert. on arrow - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN FCE PNELS: 1/8 thick aluminum sign face panels; mechanically fasten sign panels to support tube structure with stainless steel countersunk screws, paint heads to match sign face; digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels; all exposed surfaces, returns, etc. to be clearcoated to prevent corrosion SUPPORT FRME/SUSPENSION: fabricated 2 square aluminum support tube frame and vertical suspension tube structure; all exposed support frame tube ends to be capped with aluminum; all welds on frame/caps to be filled and ground smooth for uniform appearance; suspension tubes mechanically attached to ceiling attachment hinge plates above; ceiling attachment plates to be mechanically fastened to garage s structural ceiling elements as required with mech. fasteners (fabricator to field verify); support frame, suspension tubes and hinge plates to be painted all exposed surfaces with MP paint to match, satin finish Sheet: '-0" 9" 9" 1'-6" varies EXIT 1'-6" varies EXIT 2 1 / field verify GRPHICS / COLORS / DECORTION NOTES L2 Typeface: font = ClearviewText Bold Universal Symbols: IG/TXDOT style symbol artwork 2 ELEVTION 3 END VIEW 4 ELEVTION (OPPOSITE SIDE) S3 V4 Veh. rrow(s): use only official MUTCD/TXDOT arrow art VINYL (FILM) / DIGITL PRINT: Light Green: match PMS 368C V7 White: 3M 4090 DG3 White (Reflective) V9 Blue: 3M 4095 DG3 Blue (Reflective) PINT: Silver: Matthews Paint #MP30136 Brushed luminum, satin finish 6.2 S DIRECTIONLS 6-10

58 REFLECTIVE / DYNMIED 5-DR.10 DIRECTIONL FSCI MOUNT GENERL DESCRIPTION & USE VEHICULR - Primary Garage Entrance Directional GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. V8 11'-1" 4" 1'-8" 7 1 / 1'-8" TBD X 6 1 / 20'-0" 19'-0" Parking $XX per day 11 1 / V9 V7 V7 V7 - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES 20'-0" Gates XXX-XXX Gates XXX-XXX 5" 9" 1'-1" 1'-4" 1" S3 V7 V7 OVERHED SIGN MOUNTING STRUCTURE: TXDOT overhead sign mounting structure, mounted to existing architectural building structures (determined per sign location); designed, engineered and installed by others per all TXDOT/MUTCD requirements; all structural attachment, sizing, type, amount and electrical feeds/components to be determined and engineered by a licensed engineer to meet or exceed all applicable codes 1 PLN VIEW Scale: 1/8 = 1-0 Sheet: '-9 1 / 9'-9 1 / 1" FCE LYOUT OVERHED SIGN PNELS: Standard TXDOT 12 H fabricated aluminum sign panel face U-extrusions mechanically fastened edge-to-edge to create overall sign face panel; cut ends curved to match sign face appearance as shown here; overall sign face unit mechanically fastened to standard 2nd surface TXDOT aluminum support frame/ribbing/structure; extrusions covered with 1st surface applied full-bleed 3M Reflective DG White film with digitally printed color graphics (i.e. Picasso printer); graphics to be aligned vertically/horizontally as required for seamless graphic presentation as shownall sign element attachment, sizing, type, amount and electrical feeds/components to be determined and engineered by a licensed engineer to meet or exceed all applicable codes DYNMIC SPCE COUNT UNIT: match existing product used in latest garage improvement programs (or DFW irport approved equivalent) 20'-0" 11'-1" X Parking $XX per day angle panels down at +5 Gates XXX-XXX Gates XXX-XXX field verify GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG/TXDOT style symbol artwork S3 Veh. rrow(s): use only official MUTCD/TXDOT arrow art 2 ELEVTION Scale: 1/8 = ELEVTION Scale: 1/8 = 1-0 V7 V8 VINYL (FILM): White: 3M 4090 DG3 White (Reflective) Yellow: 3M 4091 DG3 Yellow (Reflective) V9 Blue: 3M 4095 DG3 Blue (Reflective) 6.2 S DIRECTIONLS 6-11

59 REFLECTIVE 5-DR.11 DIRECTIONL FSCI MOUNT GENERL DESCRIPTION & USE VEHICULR - Garage Entry Lane Directional GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. 10'-0" V7 - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). 10'-0" 10'-0" 8'-6" 4" 1'-4" 5" 9" 1/ 7" 11" 7 1 / 11"6 1 / Gates XXX-XXX 5 1 / 8" 6 1 / 1'- V9 V7 V7 V7 V7 - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES OVERHED SIGN MOUNTING STRUCTURE: TXDOT overhead sign mounting structure, mounted to existing architectural building structures (determined per sign location); designed, engineered and installed by others per all TXDOT/MUTCD requirements; all structural attachment, sizing, type, amount and electrical feeds/components to be determined and engineered by a licensed engineer to meet or exceed all applicable codes 1 PLN VIEW Scale: 1/8 = 1-0 FCE LYOUT S3 V7 OVERHED SIGN PNELS: Standard TXDOT 12 H fabricated aluminum sign panel face U-extrusions mechanically fastened edge-to-edge to create overall sign face panel; cut ends curved to match sign face appearance as shown here; overall sign face unit mechanically fastened to standard 2nd surface TXDOT aluminum support frame/ribbing/structure; extrusions covered with 1st surface applied full-bleed 3M Reflective DG White film with digitally printed color graphics (i.e. Picasso printer); graphics to be aligned vertically/horizontally as required for seamless graphic presentation as shownall sign element attachment, sizing, type, amount and electrical feeds/components to be determined and engineered by a licensed engineer to meet or exceed all applicable codes Sheet: '-0" 10'-0" Gates XXX-XXX Gates XXX-XXX angle panels down at +5 8'-6" CLERNCE: 8-2 CLERNCE: 8-2 CLERNCE: 8-2 field verify GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium 2 ELEVTION Scale: 1/8 = ELEVTION Scale: 1/8 = 1-0 S3 Universal Symbols: IG/TXDOT style symbol artwork Veh. rrow(s): use only official MUTCD/TXDOT arrow art VINYL (FILM): V7 White: 3M 4090 DG3 White (Reflective) V9 Blue: 3M 4095 DG3 Blue (Reflective) 6.2 S DIRECTIONLS 6-12

60 REFLECTIVE 5-DR.13 DIRECTIONL BEM/WLL GENERL DESCRIPTION & USE VEHICULR - UP/DOWN Trailblazer; 1 direction; 1 side GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 10'-0" - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). 4 1 / 1'-0" 4" 2'-8" 5 1 / 7" 4" - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. 1/4" 1 PLN VIEW 10'-0" 1'-6" 1'-0" Rotate arrow on center FCE LYOUT Scale: 1/2 = 1-0 DOWN S3 V7 V7 L2 V9 V9 V7 V7 Center text vert./horiz. within box (NOTE: ID message may read UP or DOWN depending on sign location) Levels X-X Center text/symbol vert. on arrow 5 1 / 11" - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN FCE PNELS: 1/4 thick aluminum sign face panels; digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels; all exposed surfaces and returns to be painted with MP paint to match, satin finish MOUNTING: mechanically fasten sign panels to wall/beam/soffit with stainless steel tamper-proof mechanical fasteners as install conditions require (Fabricator to field verify), paint heads to match sign face; NOTE: Fabricator to use proper connection gaskets/seals/etc to elimnate corrosion from mounting surface and weather conditions as install location conditions require (Fabricator to field verify) Sheet: '-0" 1/4" varies 1'-6" DOWN Levels X-X 1'-6" field verify GRPHICS / COLORS / DECORTION NOTES 2 ELEVTION 3 END VIEW L2 S3 Typeface: font = ClearviewText Medium Typeface: font = ClearviewText Bold Universal Symbols: IG/TXDOT style symbol artwork Veh. rrow(s): use only official MUTCD/TXDOT arrow art VINYL (FILM) / DIGITL PRINT: V7 White: 3M 4090 DG3 White (Reflective) V9 Blue: 3M 4095 DG3 Blue (Reflective) 6.2 S DIRECTIONLS 6-13

61 REFLECTIVE / DYNMIED 5-DR.14 DIRECTIONL BEM/WLL GENERL DESCRIPTION & USE VEHICULR - Directional w/ Static & Dynamic message; 1 direction; 1 side GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 4 1 / 1'-0" 4" 7" 4 1 / 7'- 3 1 / match existing - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. TBD 1 PLN VIEW 7'- 1'-6" Rotate arrow on center 1'-0" FCE LYOUT Scale: 1/2 = 1-0 S3 V7 D2 V7 1 Hour 0000 Center text/symbol vert. on arrow 5 1 / 7" - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN BOX: fabricated aluminum extrusion frame with removable aluminum face panels, all welds filled and ground smooth for seamless appearance; removable faces use internal hidden top aluminum panel clip and are mechanically fastened with countersunk S.S. screws at bottom returns eges of extrusion frame (paint screwheads to match returns) into internal aluminum angle; vertical support tubes mechanically fastened to top of sign box extrusion frame; digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels; all exposed surfaces, returns, etc to be painted with MP paint to match, satin finish; routed cut-outs in face panels and vents in sign box sized per dynamic unit required MOUNTING: mechanically fasten sign panels to wall/beam/soffit with stainless steel tamper-proof mechanical fasteners as install conditions require (Fabricator to field verify), paint heads to match sign face; NOTE: Fabricator to use proper connection gaskets/seals/etc to elimnate corrosion from mounting surface and weather conditions as install location conditions require (Fabricator to field verify) DYNMIC SPCE COUNT UNIT: By others Sheet: '- 1'-6" 1 Hour '-6" TBD field verify 2 ELEVTION 3 END VIEW GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG/TXDOT style symbol artwork S3 Veh. rrow(s): use only official MUTCD/TXDOT arrow art V7 V9 VINYL (FILM) / DIGITL PRINT: White: 3M 4090 DG3 White (Reflective) Blue: 3M 4095 DG3 Blue (Reflective) 6.2 S DIRECTIONLS 6-14

62 REFLECTIVE 5-DR.15 DIRECTIONL BEM/WLL GENERL DESCRIPTION & USE VEHICULR - Valet Trailblazer; 1 direction; 1 side GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. 4'-8" - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 4 1 / 1'-0" 4" 7" 3 1 / - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). 1'-6" 1'-0" Valet 5 1 / - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES 1 PLN VIEW 1/4" 4'-8" Rotate arrow on center FCE LYOUT Scale: 1/2 = 1-0 S3 V7 V7 V9 V7 Center text/symbol vert. on arrow SIGN FCE PNELS: 1/4 thick aluminum sign face panels; digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels; all exposed surfaces and returns to be painted with MP paint to match, satin finish MOUNTING: mechanically fasten sign panels to wall/beam/soffit with stainless steel tamper-proof mechanical fasteners as install conditions require (Fabricator to field verify), paint heads to match sign face; NOTE: Fabricator to use proper connection gaskets/seals/etc to elimnate corrosion from mounting surface and weather conditions as install location conditions require (Fabricator to field verify) Sheet: '-8" 1/4" 1'-6" Valet 1'-6" field verify 2 ELEVTION 3 END VIEW GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG/TXDOT style symbol artwork S3 Veh. rrow(s): use only official MUTCD/TXDOT arrow art V7 V9 VINYL (FILM) / DIGITL PRINT: White: 3M 4090 DG3 White (Reflective) Blue: 3M 4095 DG3 Blue (Reflective) 6.2 S DIRECTIONLS 6-15

63 REFLECTIVE / DYNMIED 5-DR.16 DIRECTIONL BEM/WLL GENERL DESCRIPTION & USE VEHICULR - Space Count Directional; 1 direction; 1 side GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. 4 1 / 1'-0" 4" 7" 4'-8" 3 1 / match existing - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). 1'-6" 1'-0" 0000 Valet - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES 1 PLN VIEW TBD 4'-8" Rotate arrow on center FCE LYOUT Scale: 1/2 = 1-0 S3 V7 V7 V9 Center text/symbol vert. on arrow SIGN BOX: fabricated aluminum extrusion frame with removable aluminum face panels, all welds filled and ground smooth for seamless appearance; removable faces use internal hidden top aluminum panel clip and are mechanically fastened with countersunk S.S. screws at bottom returns eges of extrusion frame (paint screwheads to match returns) into internal aluminum angle; vertical support tubes mechanically fastened to top of sign box extrusion frame; digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels; all exposed surfaces, returns, etc to be painted with MP paint to match, satin finish; routed cut-outs in face panels and vents in sign box sized per dynamic unit required MOUNTING: mechanically fasten sign panels to wall/beam/soffit with stainless steel tamper-proof mechanical fasteners as install conditions require (Fabricator to field verify), paint heads to match sign face; NOTE: Fabricator to use proper connection gaskets/seals/etc to elimnate corrosion from mounting surface and weather conditions as install location conditions require (Fabricator to field verify) DYNMIC SPCE COUNT UNIT: By others Sheet: '-8" 1'-6" 0000 Valet 1'-6" TBD field verify GRPHICS / COLORS / DECORTION NOTES 2 ELEVTION 3 END VIEW L2 Typeface: font = ClearviewText Medium Typeface: font = ClearviewText Bold Universal Symbols: IG/TXDOT style symbol artwork S3 Veh. rrow(s): use only official MUTCD/TXDOT arrow art VINYL (FILM) / DIGITL PRINT: V7 White: 3M 4090 DG3 White (Reflective) V9 Blue: 3M 4095 DG3 Blue (Reflective) 6.2 S DIRECTIONLS 6-16

64 REFLECTIVE / DYNMIED 5-DR.17 DIRECTIONL BEM/WLL GENERL DESCRIPTION & USE VEHICULR - Directionals w/ 2 per Direction; 2 directions; 1 side GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. 4 1 / 1'-0" 4 1 / 7" 9'-0" - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). TBD 1 PLN VIEW 9'-0" 9'-0" 1'-10" Rotate arrow on center S3 V7 V7 V7 FCE LYOUT Scale: 1/2 = 1-0 Gates XXX-XXX Valet / 1 Hour 0000 Center text/symbol vert. on arrow - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN BOX: fabricated aluminum extrusion frame with removable aluminum face panels, all welds filled and ground smooth for seamless appearance; removable faces use internal hidden top aluminum panel clip and are mechanically fastened with countersunk S.S. screws at bottom returns eges of extrusion frame (paint screwheads to match returns) into internal aluminum angle; vertical support tubes mechanically fastened to top of sign box extrusion frame; digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels; all exposed surfaces, returns, etc to be painted with MP paint to match, satin finish; routed cut-outs in face panels and vents in sign box sized per dynamic unit required MOUNTING: mechanically fasten sign panels to wall/beam/soffit with stainless steel tamper-proof mechanical fasteners as install conditions require (Fabricator to field verify), paint heads to match sign face; NOTE: Fabricator to use proper connection gaskets/seals/etc to elimnate corrosion from mounting surface and weather conditions as install location conditions require (Fabricator to field verify) DYNMIC SPCE COUNT UNIT: By others Sheet: 0.06 TBD 1'-10" Gates XXX-XXX Valet / 1 Hour 0000 Gates XXX-XXX Level X: dditional field verify 1'-0" 3 1 / match existing 5" 5" 5" 9'-0" 9'-0" 1'-10" 2 ELEVTION 3 END VIEW GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG/TXDOT style symbol artwork S3 Veh. rrow(s): use only official MUTCD/TXDOT arrow art V7 V9 VINYL (FILM) / DIGITL PRINT: White: 3M 4090 DG3 White (Reflective) Blue: 3M 4095 DG3 Blue (Reflective) 6.2 S DIRECTIONLS 6-17

65 REFLECTIVE 5-DR.18 DIRECTIONL BEM/WLL GENERL DESCRIPTION & USE VEHICULR - Exit Trailblazer; 1 direction; 1 side GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. 1'-6" 1/ 1'-0" 1/ 5'-0" 1/ 3 1 / 1'-0" 4" 10 1 / 4" 1/ V4 V7 EXIT 7" - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN FCE PNELS: 1/4 thick aluminum sign face panels; digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels; all exposed surfaces and returns to be painted with MP paint to match, satin finish 1 PLN VIEW 5'-0" Rotate arrow on center FCE LYOUT Scale: 1/2 = 1-0 S3 V7 V7 V9 L2 V7 Center text/symbol vert. on arrow MOUNTING: mechanically fasten sign panels to wall/beam/soffit with stainless steel tamper-proof mechanical fasteners as install conditions require (Fabricator to field verify), paint heads to match sign face; NOTE: Fabricator to use proper connection gaskets/seals/etc to elimnate corrosion from mounting surface and weather conditions as install location conditions require (Fabricator to field verify) Sheet: '-0" 1'-6" EXIT field verify 1'-6" GRPHICS / COLORS / DECORTION NOTES 2 ELEVTION 3 END VIEW L2 S3 Typeface: font = ClearviewText Bold Universal Symbols: IG/TXDOT style symbol artwork Veh. rrow(s): use only official MUTCD/TXDOT arrow art VINYL (FILM) / DIGITL PRINT: V4 Light Green: match PMS 368C V7 White: 3M 4090 DG3 White (Reflective) V9 Blue: 3M 4095 DG3 Blue (Reflective) 6.2 S DIRECTIONLS 6-18

66 REFLECTIVE 5-DR.19 DIRECTIONL BEM/WLL GENERL DESCRIPTION & USE VEHICULR - Garage Ramp Entry Directional GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. 9'-0" 2'-0" 1'-0" 1'-0" 1/4" 1/4" 8" 11 1 / L2 V9 V7 V7 V9 V7 2'-4" 4" LIGN DOWN Levels X-X EXIT Use: Level X 7'-7" 1/4" 7'-7 1 / 1/4" 7" 9'-0" 10" 1'-4 1 / 5" 3 1 / 5" 3 1 / - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN FCE PNELS: 1/4 thick aluminum sign face panels; digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels; all exposed surfaces and returns to be painted with MP paint to match, satin finish 1 PLN VIEW Center text/symbol V7 V9 L2 V7 V4 V7 V7 vert. on arrow S3 V7 FCE LYOUT Scale: 1/2 = 1-0 MOUNTING: mechanically fasten sign panels to wall/beam/soffit with stainless steel tamper-proof mechanical fasteners as install conditions require (Fabricator to field verify), paint heads to match sign face; NOTE: Fabricator to use proper connection gaskets/seals/etc to elimnate corrosion from mounting surface and weather conditions as install location conditions require (Fabricator to field verify) Sheet: '-0" 2'-0" DOWN Levels 1-2 X-X EXIT Use: Level 1X 2'-0" field verify GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium 2 ELEVTION 3 END VIEW L2 S3 Typeface: font = ClearviewText Bold Universal Symbols: IG/TXDOT style symbol artwork Veh. rrow(s): use only official MUTCD/TXDOT arrow art VINYL (FILM) / DIGITL PRINT: V4 Light Green: match PMS 368C V7 White: 3M 4090 DG3 White (Reflective) V9 Blue: 3M 4095 DG3 Blue (Reflective) 6.2 S DIRECTIONLS 6-19

67 REFLECTIVE 5-DR.21 DIRECTIONL BEM/WLL GENERL DESCRIPTION & USE PEDESTRIN - Beam/Wall Mount Terminal Trailblazer GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 5'-0" - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). 9 1 / 4 1 / 6" 6" 2 1 / 7 1 / Terminal X V7 - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES 1 PLN VIEW 5'-0" Center text/symbol vert. on arrow FCE LYOUT Scale: 1/2 = 1-0 V7 V9 V7 V7 V8 Rotate arrow on center SIGN FCE PNELS: 1/4 thick aluminum sign face panels; digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels; all exposed surfaces and returns to be painted with MP paint to match, satin finish MOUNTING: mechanically fasten sign panels to wall/beam/soffit with stainless steel tamper-proof mechanical fasteners as install conditions require (Fabricator to field verify), paint heads to match sign face; NOTE: Fabricator to use proper connection gaskets/seals/etc to elimnate corrosion from mounting surface and weather conditions as install location conditions require (Fabricator to field verify) Sheet: '-0" 9 1 / Terminal X 9 1 / field verify GRPHICS / COLORS / DECORTION NOTES 2 ELEVTION 3 END VIEW Typeface: font = ClearviewText Medium Universal Symbols: use only offical DFW symbol artwork rrow(s): use only official DFW wayfinding arrow artwork VINYL (FILM) / DIGITL PRINT: V7 White: 3M 4090 DG3 White (Reflective) V8 Yellow: 3M 4091 DG3 Yellow (Reflective) V9 Blue: 3M 4095 DG3 Blue (Reflective) 6.2 S DIRECTIONLS 6-20

68 INTERNL 5-DR.25 DIRECTIONL BEM/WLL GENERL DESCRIPTION & USE PEDESTRIN - Garage Section Directional (exterior pedestrian entrances) GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 5'-0" 1" 4'-10" 1" 5'-0" 1" 4'-10" 1" - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. 1 1 / 2 1 / 8" 2 1 /4" 1 1 / 1 1 / 2 1 / 8" 2 1 /4" 1 1 / - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES 15'-0" 1'-4" 1'-1" 2 1 / 2 1 / 8" Sections X-X 1'-4" 1'-1" 2 1 / 2 1 / 8" Sections X-X Valet 2 1 / CBINETS: - SIGN CBINET: two-piece extruded aluminum frame; cabinet has internal hinges at bottom to allow removal of face frame for access to copy panel and LED light module; powdercoat all exposed surfaces to match, satin finish 1 PLN VIEW 1 1 / FCE LYOUT Scale: 1/2 = / B FCE LYOUT Scale: 1/2 = FCE FRME: hinged at bottom and secured with FHMS at top; translucent white, 3/16 thick acrylic copy panel with first surface applied vinyl; V1 is secured to face frame with.090 thick aluminum retainers inside frame; frame slides forward on hinges and pivots 15 degree max. to remove - BCK FRME: hinged at bottom to receive face frame; contains LED light module; 1/8 thick aluminum back panel is welded to extruded frame; receives mounting bracket and Z clips for mounting to angled mounting bracket MOUNTING: mount to wall structural elements with connection system as installation location conditions require; provide seal at all exterior wall penetrations (Fabricator to coordinate connection location/type of structural elements with General Contractor), B Sheet: '-0" 5'-0" 5'-0" 5'-0" V1 field verify 1'-4" varies Sections X-X Sections X-X Valet Sections X-X varies 1'-4" GRPHICS / COLORS / DECORTION NOTES 2 ELEVTION 3 END VIEW Typeface: font = ClearviewText Medium Universal Symbols: use only offical DFW symbol artwork rrow(s): use only official DFW wayfinding arrow artwork VINYL (FILM) / DIGITL PRINT: V1 Blue: 3M EC Sapphire Blue PINT: Blue: Powder coated polyester TGIC #PLS1528PT 6.2 S DIRECTIONLS 6-21

69 INTERNL 5-DR.26 DIRECTIONL BEM/WLL GENERL DESCRIPTION & USE PEDESTRIN - Garage Section Directional w/ Welcome ID (interior areas near elevator cores) GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. 15'-0" - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 6" - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). 1 PLN VIEW 15'-0" 2'-0" 9 1 / 1/ 1'- 3 1 / 8" Center text/symbol vert. on arrow 3 1 / 8" 2 1 /4" FCE LYOUT Scale: 1/2 = 1-0 Sections X-X Welcome to X Sections X-X Parking 8" 2 1 /4" 1/ 1/ Rotate arrow on center 2 1 / Section X Sections X-X 4"2 1 / 8" 3 1 / - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES CBINETS: - SIGN CBINET: two-piece extruded aluminum frame; cabinet has internal hinges at bottom to allow removal of face frame for access to copy panel and LED light module; powdercoat all exposed surfaces to match, satin finish - FCE FRME: hinged at bottom and secured with FHMS at top; translucent white, 3/16 thick acrylic copy panel with first surface applied vinyl; V1 is secured to face frame with.090 thick aluminum retainers inside frame; frame slides forward on hinges and pivots 15 degree max. to remove - BCK FRME: hinged at bottom to receive face frame; contains LED light module; 1/8 thick aluminum back panel is welded to extruded frame; receives mounting bracket and Z clips for mounting to angled mounting bracket MOUNTING: mount to wall structural elements with connection system as installation location conditions require; provide seal at all exterior wall penetrations (Fabricator to coordinate connection location/type of structural elements with General Contractor) Sheet: 0.06 V3 V1 15'-0" 2'-0" Sections X-X Welcome to X Parking Sections X-X Section X Sections X-X 2'-0" field verify GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium 2 ELEVTION 3 END VIEW Universal Symbols: use only offical DFW symbol artwork rrow(s): use only official DFW wayfinding arrow artwork VINYL (FILM) / DIGITL PRINT: V1 Blue: 3M EC Sapphire Blue V3 Yellow: 3M Sunflower PINT: Blue: Powder coated polyester TGIC #PLS1528PT 6.2 S DIRECTIONLS 6-22

70 REFLECTIVE 5-DR.31 DIRECTIONL SUSPENDED GENERL DESCRIPTION & USE PEDESTRIN - Terminal Trailblazer GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 5'-0" - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). 1 PLN VIEW Sheet: 0.06 field verify 9 1 /varies 2 1 / 5'-0" 5'-0" 5" 5" Terminal X Existing Bollard Existing Bollard 9 1 /varies 2 1 / 9 1 / Center text/symbol vert. on arrow FCE LYOUT Scale: 1/2 = / Existing Bollard 6" 6" 2 1 / 7 1 / Terminal X V7 V9 V7 V7 V8 Existing Bollard Terminal X V7 Rotate arrow on center - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN FCE PNELS: 1/8 thick aluminum sign face panels; mechanically fasten sign panels to support tube structure with stainless steel countersunk screws, paint heads to match sign face; digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels; all exposed surfaces, returns, etc. to be clearcoated to prevent corrosion SUPPORT FRME/SUSPENSION: fabricated 2 square aluminum support tube frame and vertical suspension tube structure; all exposed support frame tube ends to be capped with aluminum; all welds on frame/caps to be filled and ground smooth for uniform appearance; suspension tubes mechanically attached to ceiling attachment hinge plates above; ceiling attachment plates to be mechanically fastened to garage s structural ceiling elements as required with mech. fasteners (fabricator to field verify); support frame, suspension tubes and hinge plates to be painted all exposed surfaces with MP paint to match, satin finish GRPHICS / COLORS / DECORTION NOTES 2 ELEVTION 3 END VIEW 4 ELEVTION (OPPOSITE SIDE) Typeface: font = ClearviewText Medium Universal Symbols: use only offical DFW symbol artwork rrow(s): use only official DFW wayfinding arrow artwork VINYL (FILM) / DIGITL PRINT: V7 White: 3M 4090 DG3 White (Reflective) V8 Yellow: 3M 4091 DG3 Yellow (Reflective) V9 Blue: 3M 4095 DG3 Blue (Reflective) 6.2 S DIRECTIONLS 6-23

71 REFLECTIVE 5-DR.41 DIRECTIONL POST MOUNT GENERL DESCRIPTION & USE PEDESTRIN - Terminal Trailblazer GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 5'-0" - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). 6" 6" 2 1 / 7 1 / - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. 9 1 / 4 1 / Terminal X V7 - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES Center text/symbol vert. on arrow V7 V9 V7 V7 V8 Rotate arrow on center SIGN FCE PNELS: 1/4 thick aluminum sign face panels; mechanically fasten sign panels to support tube structure with stainless steel tamper-proof screws, paint heads to match sign face; digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels; all exposed surfaces, returns, etc. to be painted with MP paint to match, satin finish 1 PLN VIEW FCE LYOUT Scale: 1/2 = 1-0 SUPPORT FRME/POST TTCHMENT: fabricated 1 square aluminum support tube frame structure; all exposed support frame tube ends to be capped with aluminum; all welds on frame/caps to be filled and ground smooth for uniform appearance; support frame mechanically attached to light post attachment band; attachment band to be mechanically fastened to light post as required w/ mech. fasteners (fabricator to field verify); support frame and attachment bands to be painted all exposed surfaces with MP paint to match, satin finish LIGHT POST: existing light post at existing garage roof areas; fabricator to field verify light post conditions and engineer sign attachment to light posts as install locations require (NOTE: light post shown is artist rendering only and may not be representative of final light post product). Sign Type 5-ID.52 Sheet: '-0" 9 1 / Terminal X Terminal X 8'-0" GRPHICS / COLORS / DECORTION NOTES 2 ELEVTION 3 END VIEW 4 ELEVTION Typeface: font = ClearviewText Medium Universal Symbols: use only offical DFW symbol artwork rrow(s): use only official DFW wayfinding arrow artwork VINYL (FILM) / DIGITL PRINT: V7 White: 3M 4090 DG3 White (Reflective) V8 Yellow: 3M 4091 DG3 Yellow (Reflective) V9 Blue: 3M 4095 DG3 Blue (Reflective) 6.2 S DIRECTIONLS 6-24

72 REFLECTIVE 5-DR.53 DIRECTIONL POST MOUNT GENERL DESCRIPTION & USE VEHICULR - Roadside/Roof Level Exit Trailblazer GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. 5'-0" 1'-4" S3 V7 1'- 5 1 / 5'-0" - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 1 PLN VIEW TBD 5'-0" V7 V9 3'-7" 3/4" 3/4" 1'- 5" 1'-4" FCE LYOUT Scale: 1/2 = 1-0 EXIT 1'- 5 1 /4" 3/4" 3/4" L2 V7 9" V4 V7 V7 V9 3'-7" 3/4" 1'- 1'-4" 5" 3/4" B EXIT 1'-4" LTERNTE FCE LYOUT OPTION Scale: 1/2 = 1-0 L2 S3 V7 V4 V7 V7 - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN FCE PNELS: 1/4 thick aluminum sign face panels; mechanically fasten sign panels to support tube structure with stainless steel tamper-proof screws, paint heads to match sign face; digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels; all exposed surfaces, returns, etc to be painted with MP paint to match, satin finish SUPPORT FRME/POST TTCHMENT: fabricated 1 square aluminum support tube frame structure; all exposed support frame tube ends to be capped with aluminum; all welds on frame/caps to be filled and ground smooth for uniform appearance; support frame mechanically attached to support post as required w/ mech. fasteners (fabricator to field verify); support frame to be painted all exposed surfaces with MP paint to match, satin finish PORTBLE PYRMID BSE and POLE: By others. Mount per manufacturer recommendations. SUPPORT POST: Fabricated square aluminum vertical support post tube; support post tube end to be capped with aluminum; all welds on frame/caps to be filled and ground smooth for uniform appearance; support post welded to foot plate and mechanically attached to concrete bollard; all support post/attachment plate/fasteners and exposed surfaces to be painted with MP paint to match, satin finish Sheet: 0.06 B Sheet: 0.06 F5 EXISTING CONCRETE BOLLRD: Existing concrete bollard 5'-0" TBD 5'-0" 3'-7" EXIT 3'-7" 3'-7" EXIT 9'-0" (field verify) 9'-0" (field verify) F5 GRPHICS / COLORS / DECORTION NOTES L2 Typeface: font = ClearviewText Bold Universal Symbols: IG/TXDOT style symbol artwork S3 Veh. rrow(s): use only official MUTCD/TXDOT arrow art VINYL (FILM) / DIGITL PRINT: V4 Light Green: match PMS 368C 2 ELEVTION w/ Portable Base 3 END VIEW 4 ELEVTION w/ Existing Concrete Bollard V7 V9 White: 3M 4090 DG3 White (Reflective) Blue: 3M 4095 DG3 Blue (Reflective) PINT: Silver: Matthews Paint #MP30136 Brushed luminum, satin finish 6.2 S DIRECTIONLS 6-25

73 NON-ILLUMINTED 5-ID.01 IDENTIFICTION WLL/BEM/COLUMN GENERL DESCRIPTION & USE VEHICULR - Ramp Entry ID Graphics field verify +/- 1'- GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. field verify +/- 1'-11" 6" EXIT L2 +/- 7" field verify - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES BCKGROUND RE: paint existing background area with MP paint, satin finish; field verify existing background surface area conditions and prep with primer prior to painting per paint manufacturer s specifications RROW GRPHICS: paint arrow with MP paint, satin finish; field verify existing background surface area conditions and prep with primer prior to painting per paint manufacturer s specifications LRGE EXIT LETTERS: paint letters with MP paint, satin finish; field verify existing background surface area conditions and prep with primer prior to painting per paint manufacturer s specifications +/- FCE LYOUT Scale: 3/8 = 1-0 field verify P5 Sheet: 0.06 field verify field verify ELEVTION VIEW 2 P5 P5 field verify NOTE: Lines of sign type 5-DR.19 typical mounting locations ELEVTION VIEW 1 EXIT P4 P5 field verify field verify P4 P4 field verify 1 ELEVTION: Ramp Entrance Inner Wall rea (Typical) field verify field verify field verify field verify NOTE: Elevation shown is typical example only; elevation varies per level and each garage vehicular ramp entrance location; field verify each location 2 ELEVTION: Ramp Entrance Threshold rea (Typical) NOTE: Elevation shown is typical example only; elevation varies per level and each garage vehicular ramp entrance location; field verify each location field verify GRPHICS / COLORS / DECORTION NOTES L2 Typeface: ClearviewText Bold PINT: P4 White: MP paint # MP05317, satin fin. P5 Exit Light Green: MP paint to match PMS 368C, satin fin. 6.2 S IDENTIFICTION 6-26

74 1'-10 1/ 1'-10 1/ EXIST. COLUMN 1'-10 1/ 1'-10 1/ REFLECTIVE 5-ID.51 3'-7" 2'-1 7 1/ 5" 1 3/4" 2 1/ 9" 3/8" 2 1/4" 2 1/ 6 1/ IDENTIFICTION WLL/COLUMN 1'-10 1/ 5" Parking Level X Section XX CENTER TEXT 1'-8 1/ 2 1/ 3'-7" 2'-1 7 1/ GENERL DESCRIPTION & USE PEDESTRIN - Wall/Column Mount Garage Section ID; 1 side 5" 4 1/ 4" 4" 1'-3 1/ 1'-10 1/ 5" Parking Level X CENTER TEXT 2 1/ GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION NOTES (GENERL DESIGN INTENT) SIGN FCE PNELS: 1/8 thick aluminum. sign face panels; mechanically fasten sign panels to garage support column/walls as install conditions require (field verify); digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels COLUMNS: existing garage vertical support column; fabricator to field verify column conditions and engineer sign attachment to columns as install locations require 1 PLN VIEW FCE LYOUT: Row Sides Scale: 1/2 = 1-0 B FCE LYOUT: Non-Row Sides Scale: 1/2 = 1-0 Sheet: 0.06 B Sheet: '-10 1/ 1'-10 1/ 3'-7" X Parking Level X Section XX Dx 3'-7" X X X X Dx Parking Level 1 Parking Level 2 Parking Level 3 Parking Level 4 max. 4'-7" Center sign on exist. column (typ.) max. 4'-7" Center sign on exist. column (typ.) GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: use only offical DFW symbol artwork VINYL (FILM) / DIGITL PRINT: 2 ELEVTION: Row Sides 3 Non-Row Sides Dx DFW Wayfinding Blue: to match PMS 662C Garage Level ID Digital Print Colors: - Level 1: Red = to match PMS 186C - Level 2: Purple = to match PMS 2587C - Level 3: Yellow = to match PMS 108C - Level 4: Orange = to match PMS 158C - Level 5: Blue = to match PMS 2727C 6.2 S IDENTIFICTION 6-27

75 Center signs on exist. light pole (typ.) 1'-10 1/ REFLECTIVE 5-ID.52 IDENTIFICTION LIGHT POLE 3'-7" 2'-1 7 1/ GENERL DESCRIPTION & USE PEDESTRIN - Light Pole Mount Garage Section ID; 2 sides 1'-10 1/ 5" Parking Level X Section XX CENTER TEXT 1'-8 1/ 2 1/ GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION NOTES (GENERL DESIGN INTENT) SIGN FCE PNELS: match existing fabrication and light post attachment methods (as installed at Terminal garage); digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels LIGHT POST: existing light post at existing garage roof areas; fabricator to field verify light post conditions and engineer sign attachment to light posts as install locations require (NOTE: light post shown is artist rendering only and may not be representative of final light post product). 1 PLN VIEW FCE LYOUT Scale: 1/2 = 1-0 1'-10 1/ 1'-10 1/ Sheet: '-7" X Parking Level X Section XX Dx X Parking Level X Section XX Dx Center sign on exist. light pole (typ.) Center sign on exist. light pole (typ.) match existing (field verify) match existing (field verify) 3'-7" 5" 1 3/4" 2 1/ 9" 3/8" 2 1/4" 2 1/ 6 1/ GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: use only offical DFW symbol artwork VINYL (FILM) / DIGITL PRINT: 2 ELEVTION 3 ELEVTION (Opposite Side) Dx DFW Wayfinding Blue: to match PMS 662C Garage Level ID Digital Print Colors: - Level 1: Red = to match PMS 186C - Level 2: Purple = to match PMS 2587C - Level 3: Yellow = to match PMS 108C - Level 4: Orange = to match PMS 158C - Level 5: Blue = to match PMS 2727C 6.2 S IDENTIFICTION 6-28

76 1'-0" 1'-0" 4" 5" REFLECTIVE 1'-10 1/ 5" Parking 2 1/ 5-ID.53, 5-ID.54 IDENTIFICTION COLUMN MOUNT 7 1/ 5" GENERL DESCRIPTION & USE PEDESTRIN - 1 Hour Parking Identification; Valet Identification; 1 side 1'-10 1/ 5" Parking 2 1/ GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). 7'-0" 4" 1 Hour Valet 10.5" TEXT 10.5" TEXT 5'-7 1/ 5'-0" 2 1/ - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION NOTES (GENERL DESIGN INTENT) SIGN FCE PNELS: 1/8 thick aluminum. sign face panels; mechanically fasten sign panels to garage support column/walls as install conditions require (field verify); digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of face panels COLUMNS: existing garage vertical support column; fabricator to field verify column conditions and engineer sign attachment to columns as install locations require DETIL : Face Layout - 5-ID.53 Scale: 3/8 = 1-0 B DETIL B: Face Layout - 5-ID.54 Scale: 3/8 = 1-0 Sheet: '-10 1/ (field verify) B 1'-10 1/ (field verify) Sheet: 1.04 X Parking X Parking X Dx Dx 7'-0" 3'- 1 Hour 3'- 5'-0" Valet 1 ELEVTION (TYPICL): 5-ID.53 2 ELEVTION (TYPICL): 5-ID.54 GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: use only offical DFW symbol artwork Dx VINYL (FILM) / DIGITL PRINT: DFW Wayfinding Blue: to match PMS 662C Digital Print Colors: - Valet ID: Gray = to PMS Cool Gray 10C - 1 Hour: Blue = to match PMS 662C 6.2 S IDENTIFICTION 6-29

77 NON-ILLUMINTED 5-ID.55 IDENTIFICTION WLL MOUNT GENERL DESCRIPTION & USE PEDESTRIN - Large Wall Mount Garage Entrance ID (Typical) GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. 1'-8" varies (field verify) 1'-8" 7" CENTER SYM. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. varies (field verify) 7" 8" 1" 8" 1'-8" 6" 1'-8" Parking Sections X-X 22'-6" DETIL : Face Layout (Typical) CENTER TEXT 1 - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES CHNNEL LETTERS: 2 deep channel letter; General Contractor to coordinate with stainless steel mesh manufacturer for typical attachment details as required.; mount to wall structural elements with connection system as installation location conditions require; provide seal at all exterior wall penetrations (Fabricator to coordinate connection location/type of structural elements with General Contractor) BCKGROUND RE: paint existing area with MP paint, satin finish; field verify existing background surface area conditions and prep with primer prior to painting per paint manufacturer s specifications varies (field verify) Sheet: 1.04 varies (field verify) P3 P4 X Parking Sections X-X P4 P4 P4 P4 Sections G-J Sections D-F DFW Valet Sections -C 1 ELEVTION (TYPICL) Scale: 1/8 = 1-0 NOTE: Elevation shown is typical example only; elevation varies per level and each garage pedestrian entrance location; field verify each location GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: use only offical DFW symbol artwork P3 P4 PINT: Blue: MP paint to match PMS 662C, satin finish Yellow: MP paint to match PMS 130C, satin finish White: MP paint # MP05317, satin finish 6.2 S IDENTIFICTION 6-30

78 NON-ILLUMINTED 5-ID.56 IDENTIFICTION WLL MOUNT 4 3/4" 1'-2 3/4" field verify 1'-2 3/4" CENTER SYM. GENERL DESCRIPTION & USE PEDESTRIN - Wall Mount Roof Level Elevator Garage/Level ID (Typical) GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 5" 1'-2 3/4" - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). 4'-10 3/4" 10" 1'- 5" 1'-2 3/4" 3/4" 4" 4" 5 1/ 5" 6 1/ Level DETIL : Face Layout (Typical) Parking Sections X-X X CENTER TEXT 12'-6" 7" 7" Elevators 8 1/ - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES CHNNEL LETTERS: 2 deep channel letter; General Contractor to coordinate with stainless steel mesh manufacturer for typical attachment details as required.; mount to wall structural elements with connection system as installation location conditions require; provide seal at all exterior wall penetrations (Fabricator to coordinate connection location/type of structural elements with General Contractor) BCKGROUND RE: paint existing area with MP paint, satin finish; field verify existing background surface area conditions and prep with primer prior to painting per paint manufacturer s specifications varies (field verify) Sheet: 1.04 P4 P4 varies (field verify) P3 P4 Level X Parking Sections X-X X Elevators P4 P4 1 ELEVTION (TYPICL) Scale: 1/8 = 1-0 NOTE: Elevation shown is typical example only; elevation varies per level and each garage pedestrian entrance location; field verify each location GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: use only offical DFW symbol artwork P3 P4 PINT: Blue: MP paint to match PMS 662C, satin finish Yellow: MP paint to match PMS 130C, satin finish White: MP paint # MP05317, satin finish 6.2 S IDENTIFICTION 6-31

79 Terminal X Terminal X Terminal X Terminal X Terminal X Terminal X Terminal X Terminal X Terminal X Terminal X Terminal X Terminal X NON-ILLUMINTED 5-ID.65 IDENTIFICTION WLL MOUNT GENERL DESCRIPTION & USE PEDESTRIN - Wall Mount Elevator Level ID/Directory GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. 4'-0" 1'-0" 4" 4" 1'-0" 4" 4" 8" 5 1/4" 5 1/4" 5 4 3Level " TEXT 3 1/4" 8" TEXT 2'-5 1/ Parking 1" Terminal Ticketing Security Checkpoint Bag Claim Terminal Curbside Bag Check 1/ PICTOGRM 0.5" TEXT 2.75" TEXT = ll symbols = ll text RROW 0.5" TEXT - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN PNEL: composite phenolic core unitized sign with integral polymetric face layer and interchangeable message panels MOUNTING: mount to wall structural elements with connection system as installation location conditions require 1" 9 3/4" DETIL : Face Layout Scale: 3/4 = 1-0 Sheet: '-5 1/ LIGN Dx 4'-0" Terminal Terminal Terminal Terminal Terminal Terminal XParkingParking XParkingParking XParkingParking XParkingParking XParking Parking XParking Level Level Level 3 3 Level 2 Level Level Dx Parking 5-ID.65a 5-ID.65b 5-ID.65c 5-ID.65d 5-ID.65e GRPHICS / COLORS / DECORTION NOTES 1 ELEVTION (TYPICL) Dx Typeface: font = ClearviewText Medium Universal Symbols: use only offical DFW symbol artwork VINYL (FILM) / DIGITL PRINT: DFW Wayfinding Blue: to match PMS 662C Garage Level ID Digital Print Colors: - Level 1: Red = to match PMS 186C - Level 2: Purple = to match PMS 2587C - Level 3: Yellow = to match PMS 108C - Level 4: Orange = to match PMS 158C - Level 5: Blue = to match PMS 2727C 6.2 S IDENTIFICTION 6-32

80 REFLECTIVE / DYNMIC 5-IN.01 INFORMTIONL GROUND MOUNT GENERL DESCRIPTION & USE VEHICULR - Roadside Level ID/Space Count Informational 5'-5" 5'-0" divider line GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. 1 PLN VIEW 5'-5" sign width to contain thickness of existing dynamic units (+/- 8" shown; field verify existing dynamic units) 9'-0" 1'- 5 1/ 5" 1/ 5 1/ 8" 5 1/ 8" 5 1/ 2 1/ 3 1/ 8" 5 1/ 8" 5 1/ FCE LYOUT Scale:1/4 = 1-0 CENTER UPPER ID TEXT Gates XXX-XXX Level Level Level THIS LEVEL Level Level match existing CENTER TEXT VERT. ON DYNMIC UNIT (TYP.) match existing 1'-4" - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FBRICTION INTENT NOTES SIGN BOX: fabricated aluminum support structure with exterior aluminum cladding; all welds to be filled and ground smooth for uniform appearance; internal support structure mechanically attached to garage floor/curb area per install location conditions requirements (field verify), use break-away connection system as required by TXDOT; digitally printed full-bleed color graphics on 3M Reflective DG White film applied to 1st surface of front face panel; all exposed surfaces, returns, etc to be painted to match, satin finish; mount dynamic units to internal support structure as required; dynamic unit faces pushed-thru front panel, 1st surface projection not to exceed.25 ; routed cut-outs in rear panel for venting of dynamic units, vents sized/spaced per dynamic unit manufacturer s requirements DYNMIC SPCE COUNT UNIT: match existing product used in latest garage improvement programs (or DFW irport approved equal) 5'-5" Sheet: 0.06 sign width to contain thickness of existing dynamic units (+/- 8" shown; field verify existing dynamic units) Gates XXX-XXX Level Level V7 D12 9'-0" D12 D7 Level THIS LEVEL V7 9'-0" Level Level GRPHICS / COLORS / DECORTION NOTES Typeface: font = ClearviewText Medium Universal Symbols: IG/TXDOT style symbol artwork 1 ELEVTION: Garage Level 3 Entrance rea (Typical) 2 SIDE VIEW VINYL (FILM) / DIGITL PRINT: V7 White: 3M 4090 DG3 White (Reflective) showing thru digitial print background D7 Med. Gray: digital print color to match PMS 431C D12 Blue: digital print color to match PINT: Blue: Powder coated polyester TGIC #PLS1528PT 6.2 S INFORMTIONL 6-33

81 NON-ILLUMINTED 5-RG.01 REGULTORY BEM GENERL DESCRIPTION & USE VEHICULR - Do Not Enter Graphics GENERL NOTES - ll final design, engineering, and amount/sizing of structural sign support elements, material types/thicknesses, dimensions, and attachment methods shall be performed and approved by a licensed engineer to meet or exceed all applicable local and national codes. - Final engineering, dimensions, materials, and fabrication are the responsibility of the Fabricator to ensure the highest quality fit and finish for all components of the completed product. ll final detailing and specifications to be provided by the Fabricator within their final approved fabrication-ready shop drawings. field verify - Wherever dissimilar metals are in contact, always separate contact surfaces prior to assembly or installation with the necessary protective coatings/gaskets/washers to prevent galvanic corrosion. 1'-4" 1'-0" L2 1'-0" 1'-4" - Final fabrication methods, quality and fit/finish to be reviewed and approved by DFW Planning Department and wayfinding/architecture Design Consultants thru prototype reviews prior to final production run/installation processes (see Performance Specifications for details). field verify 1'-4" DO NOT ENTER 10" LIGN - Colors shown are for reference only, and are subject to the limitations of the printing process and/or variance of electronic RGB screen displays. Refer to color system swatches and/or final finish samples for accurate reference. - s shown here are general placeholders only. See graphic message schedules for specific messaging by location and sign type. FCE LYOUT FBRICTION INTENT NOTES BCKGROUND RE: paint existing background area with MP paint, satin finish; field verify existing background surface area conditions and prep with primer prior to painting per paint manufacturer s specifications LRGE LETTERS/SYMBOLS: paint letters/symbols with MP paint, satin finish; field verify existing background surface area conditions and prep with primer prior to painting per paint manufacturer s specifications field verify Sheet: 0.06 NOTE: Elevation shown is typical example only; elevation varies per level and each garage vehicular entrance location; field verify each location DO NOT ENTER field verify P4 2 NOTE: Supplement overhead graphics with ground mounted regulatory Do Not Enter signs (match existing; field verify; to flank both sides of entrance area; mount with protective bollards as required per location install conditions and local codes) 1 ELEVTION: Garage Entrance rea (Typical) GRPHICS / COLORS / DECORTION NOTES L2 Typeface: ClearviewText Bold P4 2 PINT: White: MP paint # MP05317, satin fin. Safety Red: MP paint to match PMS 485C, satin fin. 6.2 S INFORMTIONL 6-34

82 PPENDIX HQ Standards

83 NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a 7.1 HQ Standards 7-1

84 NOTE: Taken from DFW International irport Headquarters document dated March 17, 2014 These documents are intended to illustrate design intent, and should only be used as a Issue Date: 7.0 PPENDIX 7.1 HQ Standards 7-2

85 NOTE: Taken from DFW International irport Headquarters document dated March 17, 2014 These documents are intended to illustrate design intent, and should only be used as a Issue Date: 7.0 PPENDIX 7.1 HQ Standards 7-3

86 NOTE: Taken from DFW International irport Headquarters document dated March 17, 2014 These documents are intended to illustrate design intent, and should only be used as a Issue Date: 7.0 PPENDIX 7.1 HQ Standards 7-4

87 Cut Letters M1 Face M3 Returns DFW irport Headquarters 2 Elevation / 1 1/2 = Building Directory B1 Dimensions & shapes of all elements as shown on G3.B1a thru G3.B1b. Cut Letters: Computer cut letters of 0.75 thick aluminum. Use Laser of Waterjet cutting method for minimal inside corner radius.buff returns smooth and even to eliminate any tooling marks. Drill and tap reverse of each element for not less than 3 threaded studs. Finish all surfaces as indicated. pply thin matte finish clear coat to all surfaces. B Frame M1 Face M3 Returns C Bar M1 Face M3 Returns D Textured Panel P6 Flight Level 003 P5 Flight Level 002 P4 Flight Level 001 E Panel P6 Level 3 P5 Level 2 P4 Level 1 Text Flight Level 003 Flight Level 002 Flight Level 001 ir Services Development Finance udit viation Real Estate Commercial Development Concessions 30 Information Technology Services Parking Treasury Business Diversity & Development Human Resources Risk Management Procurement Materials & Management Executives Legal Marketing Planning Public ffairs & Governmental ffairs Elevation / 1 1/2 = 1-0 Section Detail / Half Size 1 Schematic B Frame Spacer E Panel Typography: Clearview Text Medium, 2.5 Cap Height (Based on E ), Kerned -32% B Frame: Fabricated form of not less than luminum. ll welded construction. Grind and buff all welds smooth. No Visible tooling marks or seams. Configured with incorporated spacer to hold message & textured panel tight into frame. Configured so panels can be removable. Finish all surfaces as indicated. pply thin matte finish, clear coat to all surfaces. C Bar: luminum bar, 0.25 thick by 1 wide, cut length. buff ends smooth and even to eliminate all tooling marks. Finish all surfaces as indicated. pply thin matte finish clearcoat to all surfaces. Concealed mechanical attachment flush to frame. Position as indicated. D Textured Panel: Textured acrylic panel of thickness, crylite Colorless 0000 BO, cut to size. Texture to be second surface. Text to be screen printed to first Surface (non-textured surface) with paint color indicated. Typography: Flight Level - Clearview Text Book, Cap Height (Based on E ), Kerned 0. For 001, 002, Clearview Text Medium, 4.5 Cap Height (Based on 1 ), Kerned -50%. E Panel: crylic panel of 0.25 thickness, cut to size. Buff returns smooth, finish all surfaces as indicated. Graphics to be screened first surface. Installation: Concealed mechanical attachment of frame and message assembly flush to wall, locate as indicated. Concealed pin and silicone mount letters flush to wall. NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX 7.1 HQ Standards 7-5

88 ir Services Development udit viation Real Estate Commercial Development Concessions Finance Information Technology Services Parking Treasury Business Diversity & Development Human Resources Risk Management Procurement Materials & Management Executives Legal Marketing Planning Public ffairs & Governmental ffairs Building Directory B1 Dimensions & shapes of all elements as shown on G3.B1a thru G3.B1b. 36 CL 2 ST B1 ssembly Shown Flight Level 003 Flight Level 002 Flight Level Elevation / 3/16 = 1-0 NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a 7.1 HQ Standards 7-6

89 Flight Level Flight Level Flight Level ir Services Development udit viation Real Estate Commercial Development Concessions Executives Legal Marketing Planning Public ffairs & Governmental ffairs Finance Information Technology Services Parking Treasury Business Diversity & Development Human Resources Risk Management Procurement Materials & Management Elevator Directory B2 Dimensions & shapes of all elements as shown on G3.B2a. Textured Panel: Textured acrylic panel of thickness, crylite Colorless 0000 BO, cut to size. Buff returns smooth and even to eliminate any tooling marks. Texture to be second surface. Text to be screen printed to first Surface (non-textured surface) as indicated. Typography: Flight Level - Clearview Text Book, Cap Height (Based on F ), Kerned , 002, Clearview Text Medium, 1 Cap Height (Based on 1 ), Kerned -50% " 0.375" 11 8 B Digital Print: Computer Cut digitally printed vinyl. First surface application. Sign Contractor responsible for color match digital print to indicated colors. Textured Panel P6 Flight Level 003 P5 Flight Level 002 P4 Flight Level 001 B Digital Print ll Surfaces P6 Level 3 P5 Level 2 P4 Level 1 Text Flight Level 003 Flight Level 002 ir Services Development udit viation Real Estate Commercial Development Concessions Executives Legal Marketing Planning Public ffairs & Governmental ffairs Finance Information Technology Services Parking Treasury Sign Type B2 CL Installation: Concealed 3M VHB tape & silicone mount flush to elevator cab wall. Sign contractor to field verify conditions prior to fabrication. Flight Level 001 Business Diversity & Development Human Resources Risk Management Procurement Materials & Management Elevation / 3 = 1-0 Elevation / 1/2 = NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a 7.1 HQ Standards 7-7

90 Reception Logo Sculpture B4 Panel Dimensions & shapes of all elements as shown on G3.B4a thru G3.B4b. Logo Panel: Stainless steel plate of 0.25 thickness, cut to size. Buff returns smooth and even to eliminate any tooling marks. Etch graphics and surfaces as indicated. Design to provide artwork for logo. Installation: Concealed mechanical attachment of logo panel to wood wall with concealed full angle frame inset from all edges as indicated. Frame Section Detail / Half Size Panel M4 Face M3 Returns Panel 2-0 Frame Elevation / 1 1/2 = 1-0 Side View / 1 1/2 = NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a 7.1 HQ Standards 7-8

91 Reception Logo B4 Dimensions & shapes of all elements as shown on G3.B4a thru G3.B4.. CL. Panel.. 1 Elevation / 1/4 = 1-0 NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a 7.1 HQ Standards 7-9

92 Entry Door Identity / Disclaimer B5 Dimensions & shapes of all elements as shown on G3.B5a. Vinyl: 3M Computer Cut Vinyl graphics to be applied to first surface of glass. Color as indicated. Typography: For DFW irport Headquarters Clearview Text Bold, 1.5 Cap Height (Based on E ), Kerned -25%; For Hours of Operation, Clearview Text Medium, 1 Cap Height (Based on E ), Kerned -25%; For Symbol Text, 0.5 Cap Height (Based on E ), Kerned -25%. Interline spacing for all as indicated. Symbols: 3 Height Vinyl V1 V4 Text & Symbols Circle Slash CL CL CL 3 3 DFW IRPORT Installation: Clean surface & apply vinyl to first surface. HEDQURTERS 2.5 HOURS MON - FRI 8:30 am - 5:00 pm CL 15 DFW IRPORT HEDQURTERS HOURS MON - FRI XX:XX am - XX:XX pm NO WEPONS TOBCCO FREE LLOWED FCILITY NO WEPONS LLOWED TOBCCO FREE FCILITY Elevation / 3 = 1-0 Elevation / 3/8 = NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a This record contains Sensitive Security Information that is controlled under 49 CFR parts 7.1 HQ Standards

93 Board Room Identity B6 Dimensions & shapes of all elements as shown on G3.E6a. Cut Letters CL BORDROOM Cut Letters: luminum letters of 0.5 thickness to be computer cut Buff returns smooth and even to eliminate any tooling marks. Finish all surfaces as indicated. Concealed mechanical attachment to baseplate. all letters to be plumb. 0.5 Typography: Clearview Text Bold, 4 Cap Height (Based on M ), Kerned 0. B Baseplate: luminum plate of 0.25 thickness, cut to length of letters. Buff returns smooth and even to eliminate any tooling marks. Finish as indicated. Installation: Concealed mechanical attachment to top of soffit. Cut Letters 2 Elevation / 1/4 = 1-0 Cut Letters M1 Face M3 Returns BORDROOM 4 B Baseplate 3 ll Surfaces 0.5 Top of Wall 1 Elevation / 1 1/2 = 1-0 Section Detail / Full Size Schematic NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a This record contains Sensitive Security Information that is controlled under 49 CFR parts 7.1 HQ Standards

94 Conference /Meeting Room Identity B7 Dimensions & shapes of all elements as shown on G3.B7a. Tactile Plaque B ccent C Bars 2 Top View / Half Size Tactile Plaque: Photopolymer Plaque, 0.25 thickness, w/ raised graphics and Grade 2 Braille. Buff returns smooth and even to eliminate tooling marks. Paint finish all surfaces as indicated. Typography: Clearview Text Medium, Cap Height (Based on E ), Kerned +25%. Interline spacing of Grade 2 Braille: Height, kerning & leading per requirements of the DOJ s 2010 D Standards for ccessible Design. B ccent: crylite Colorless 0000 BO textured acrylic panel, thickness, cut to size, texture to be first surface. Rout grooves into face, no greater than configured to accept Bars. Polish returns clear, smooth and even, backpaint as indicated. Laminate to Tactile Plaque using concealed adhesive ing, aligning edges. C Bars M1 Face M3 Returns B ccent 1 Background Tactile Plaque ll Surfaces P4 Level 1 P5 Level 2 P6 Level 3 Text CONFERENCE ROOM C Bars B ccent Tactile Plaque TEM ROOM 1066 C Bars: luminum Bars 0.25 wide by thick, cut to lenght. Buff edges smooth and even to eliminate any tooling marks. Finish as indicated. pply thin and even matte finish clearcoat to all surfaces and laminate to ccent with concealed adhesive. Installation: Concealed 3M VHB tape & silicone mount flush to wall adjacent to latch side of door. Locate 58 to centerline of plaque from finished floor, 2 from door frame. t outswinging door locations maintain distance specified in DOJ 2010 D Standards for ccessible Design. Top View / Half Size Elevation / 3 = NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a This record contains Sensitive Security Information that is controlled under 49 CFR parts 7.1 HQ Standards

95 Department Identity B8 Tactile Plaque B ccent C Bars 2 Top View / Half Size 11 LOUNGE FINNCE CLL CENTER FINNCE Dimensions & shapes of all elements as shown on G3.B8a. Tactile Plaque: Photopolymer Plaque, 0.25 thickness, w/ raised graphics and Grade 2 Braille. Buff returns smooth and even to eliminate tooling marks. Paint finish all surfaces as indicated. Typography: Clearview Text Medium, Cap Height (Based on E ), Kerned +25%. Interline spacing of Grade 2 Braille: Height, kerning & leading per requirements of the DOJ s 2010 D Standards for ccessible Design. B ccent: crylite Colorless 0000 BO textured acrylic panel, thickness, cut to size, texture to be first surface. Rout grooves into face, no greater than configured to accept Bars. Polish returns clear, smooth and even, backpaint as indicated. Laminate to Tactile Plaque using concealed adhesive ing, aligning edges C Bars M1 B ccent 1 ll Surfaces 1 Background ll Surfaces Tactile Plaque ll Surfaces P4 Level 1 P5 Level 2 P6 Level 3 Text BUSINESS DIVERSITY & DEVELOPMENT PUBLIC FFIRS & GOVERNMENTL FFIRS INFORMTION TECHNOLOGY C Bars: luminum Bars 0.25 wide by thick, cut to lenght. Buff edges smooth and even to eliminate any tooling marks. Finish as indicated. pply thin and even matte finish clearcoat to all surfaces and laminate to ccent with concealed adhesive. Installation: Concealed 3M VHB tape & silicone mount flush to wall adjacent to latch side of door. Locate 58 to centerline of plaque from finished floor, 2 from door frame. t outswinging door locations maintain distance specified in DOJ 2010 D Standards for ccessible Design. Elevation / Half Size Elevation / 3 = lternate Layouts NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a This record contains Sensitive Security Information that is controlled under 49 CFR parts 7.1 HQ Standards

96 Room Identity B9 Dimensions & shapes of all elements as shown on G3.B9. Tactile Plaque: Photopolymer Plaque, 0.25 thickness, w/ raised graphics and Grade 2 Braille. Buff returns smooth and even to eliminate tooling marks. Paint finish all surfaces as indicated. EXECUTIVE FILES 3230 Typography: Clearview Text Medium, Cap Height (Based on E ), Kerned +25%. Interline spacing of Bars: 0.25 width. Tactile Plaque Tactile Plaque REVENUE CONTROL 2309 Grade 2 Braille: Height, kerning & leading per requirements of the DOJ s 2010 D Standards for ccessible Design. Installation: Concealed 3M VHB tape & silicone mount flush to wall adjacent to latch side of door. Locate 58 to centerline of plaque from finished floor, 2 from door frame. t outswinging door locations maintain distance specified in DOJ 2010 D Standards for ccessible Design. 3 Top View / Half Size 4 Elevation / 3 = Tactile Plaque ll Surfaces P4 Level 1 P5 Level 2 P6 Level 3 Text & Symbol 4 Bars INTERVIEW ROOM Tactile Plaque VITION SERVICES FILE ROOM Elevation / Half Size Size 2 Elevation / Half Size Size B NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a This record contains Sensitive Security Information that is controlled under 49 CFR parts 7.1 HQ Standards

97 NOTE: Taken from DFW International irport Headquarters document dated March 17, 2014 These documents are intended to illustrate design intent, and should only be used as a Issue Date: 7.0 PPENDIX 7.1 HQ Standards 7-15

98 Tactile Plaque Top View / Half Size Top View / Half Size 2 4 Bars Tactile Plaque B ccent C Restroom Identity Dimensions & shapes of all elements as shown on G3.B11a. B11 Tactile Plaque: Photopolymer Plaque, 0.25 thickness, w/ raised graphics and Grade 2 Braille. Buff returns smooth and even to eliminate tooling marks. Paint finish all surfaces as indicated. Typography: Clearview Text Medium, Cap Height (Based on E ), Kerned +25%. Interline spacing as indicated Tactile Plaque ll Surfaces P4 Level 1 Text & Symbol 4 Bars Grade 2 Braille: Height, kerning & leading per requirements of the DOJ s 2010 D Standards for ccessible Design. B ccent: crylite Colorless 0000 BO textured acrylic panel, thickness, cut to size. Rout grooves into face, no greater than configured to accept Bars. Polish returns clear, smooth and even, eliminating any tooling marks and backpaint at second surface. Laminate to Tactile Plaque using concealed adhesive ing, aligning edges. Tactile Plaque ll Surfaces P4 Level 1 P5 Level 2 P6 Level 3 Text & Symbol 4 Bars MEN B ccent C Bars MEN 1018 C Bars: luminum Bars 0.25 wide by thick with vertical brush finish, cut to lenght. Buff edges smooth and even to eliminate any tooling marks. pply thin and even matte finish clearcoat to all surfaces and laminate to ccent with concealed adhesive. Installation: Concealed 3M VHB tape & silicone mount flush to wall adjacent to latch side of door. Locate 58 to centerline of plaque from finished floor, 2 from door frame. t outswinging door locations maintain distance specified in DOJ 2010 D Standards for ccessible Design. Elevation / Half Size Elevation / Half Size 1 Style 3 Style B NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a This record contains Sensitive Security Information that is controlled under 49 CFR parts 7.1 HQ Standards

99 Super Graphic B12 Dimensions & shapes of all elements as shown on G3.B12a thru G3.12d. Vinyl: 3M Computer-cut Vinyl. 1st Surface application. Color as indicated. Vinyl to be applied on both sides of glass panels. Designer to provide artwork for prior to fabrication. Installation: Clean surface & apply Vinyl. Sign contractor to verify all as-built conditions prior to fabrication including dimensions and indicate on shop drawings. Ensure that all elements are uniform, parallel and aligned. 60 Frame (by others) Glass (by others) Vinyl V11 V3 V10 Trans. White Dusted Crystal Silver 144 Silver Elements Silver Elements White Elements Dusted Crystal Elements White Elements Dusted Crystal Elements 1 Elevation / 3/8 = 1-0 Lounge Panel 1, Side Shown 2 Elevation / 3/8 = 1-0 Lounge Panel 1, Side B Shown NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX 7.1 HQ Standards 7-17

100 Super Graphic B12 Dimensions & shapes of all elements as shown on G3.B12a thru G3.12d. Frame (by others) Glass (by others) Vinyl V11 V3 V10 Trans. White Dusted Crystal Silver Silver Elements Silver Elements White Elements Dusted Crystal Elements Elevation / 3/8 = 1-0 Elevation / 3/8 = Lounge Panel 2, Side Shown 2 Lounge Panel 2, Side B Shown White Elements Dusted Crystal Elements NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX 7.1 HQ Standards 7-18

101 Super Graphic B12 Dimensions & shapes of all elements as shown on G3.B12a thru G3.12d. Frame (by others) Glass (by others) Vinyl V11 V3 V10 Trans. White Dusted Crystal Silver Silver Elements Silver Elements White Elements Dusted Crystal Elements White Elements Dusted Crystal Elements 1 Elevation / 3/8 = 1-0 Lounge Panel 3, Side Shown 2 Elevation / 3/8 = 1-0 Lounge Panel 3, Side B Shown NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX 7.1 HQ Standards 7-19

102 Super Graphic B12 Dimensions & shapes of all elements as shown on G3.B12a thru G3.12d DFW Global Super-Hub 7 runways, 6 terminals on 18,000 acres 2020 DFW Global Super-Hub 7 runways, 6 terminals on 18,000 acres OC & EOC 46 non-stop and Int l markets Wright mendment settled non-stop Int l markets 2006 OC & EOC and Wright mendment settled 2005 Terminal D Opens 2003 Rental Car Facility Int l Openings Rental Car Terminal D Facility Opens Int l Openings 1997 Hyatt East Parking Garage Expansion 1996 Only airport 7 runways 1996 Only airport 7 runways 1997 Hyatt East Parking Garage Expansion Frame (by others) Smoking 2 new Banned Control Towers on flights State of the rt 2 hours or less Fire Training Center th Runway Frame (by others) new Control Towers State of the rt Fire Training Center th Runway 1988 Smoking Banned on flights 2 hours or less Glass (by others) Vinyl V11 Trans. White V3 Dusted Crystal V10 Silver 2005 Terminal D Opens 1997 Hyatt East Parking Garage Expansion Smoking Banned on flights 2 hours or less DFW Global Super-Hub 7 runways, 6 terminals on 18,000 acres OC & EOC 46 non-stop and Int l markets Wright mendment settled 2003 Rental Car Facility th Runway Int l Openings 2 new Control Towers State of the rt Fire Training Center 1996 Only airport 7 runways DFW irport Opens 1979 First Flight Wright #341 mendment 1968 Construction begins on 18,000 acre plot 1965 Birth of DFW Interim Board Silver Elements th and 5th Runways Glass (by others) Vinyl V11 Trans. White V3 Dusted Crystal V10 Silver non-stop Int l markets 1996 Only airport 7 runways 2020 DFW Global Super-Hub 7 runways, 6 terminals on 18,000 acres 2006 OC & EOC and Wright mendment settled Rental Car Terminal D Facility Opens Int l Openings 1997 Hyatt East Parking Garage Expansion new Control Towers State of the rt Fire Training Center th Runway 1988 Smoking Banned on flights 2 hours or less th and 5th Runways 1979 Wright mendment 1968 Construction begins on 18,000 acre plot 1965 Birth of DFW Interim Board Silver Elements 1974 DFW irport Opens First Flight # DFW irport Opens First Flight # Construction begins on 18,000 acre plot 1979 Wright mendment th and 5th Runways th and 5th Runways 1979 Wright mendment 1968 Construction begins on 18,000 acre plot 1974 DFW irport Opens First Flight # Birth of DFW Interim Board 1965 Birth of DFW Interim Board White Elements Dusted Crystal Elements White Elements Dusted Crystal Elements 1 Elevation / 3/8 = 1-0 History Wall, Shown 2 Elevation / 3/8 = 1-0 History Wall, Shown NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX 7.1 HQ Standards 7-20

103 NOTE: Taken from DFW International irport Headquarters document dated March 17, 2014 These documents are intended to illustrate design intent, and should only be used as a Issue Date: 7.0 PPENDIX 7.1 HQ Standards 7-21

104 Stairwell Code Sign B14 Dimensions & shapes of all elements as shown on G3.B14a. Panel: crylic plate of thickness, cut to size.buff returns smooth and even to elimnate any tooling marks. Paint all surfaces as indicated. Graphics to be screened first surface Panel STIR 1 ROOF CCESS 11 TO ROOF EXIT THIS LEVEL 2 2 Typography: s: Clearview Hwy 3-W, 1 Cap Height (Based on E ), Interline spacing as indicated. Kerned -50%. Numeral: Clearview Hwy 5-W, 5 Cap Height (Based on E ). Symbols: rrow: 3 Height; Star: 3 Height Panel 1 ll Surfaces P3 Symbol & Text STIR 1 NO ROOF CCESS B Tactile Plaque: Photopolymer Plaque, thickness, w/ raised graphics and Grade 2 Braille. Buff returns smooth and even to eliminate tooling marks. Paint finish all surfaces as indicated. Laminate to panel with concealed adhesive, align edges. Typography: Clearview Text Bold, Cap Height (Based on E ) Mounting Elevation / 3/8 = 1-0 Grade 2 Braille: Height, kerning & leading per requirements of the DOJ s 2010 D Standards for ccessible Design. 31 TO Panel STIR 1 NO ROOF CCESS Panel STIR 1 NO ROOF CCESS Installation: Concealed VHB tape & silicone mount holder assembly flush to wall at 56 above finish floor to bottom of sign. Locate on wall outside stair where sign is visible. Owner to field verify position. 4 B Tactile Plaque 1 ll Surfaces P3 Text DOWN TO LEVEL 1 TO EXIT 3 21 TO 3 DOWN TO LEVEL 1 TO EXIT Elevation / 3 = 1-0 Elevation / 1 1/2 = TO 3 EXIT THIS LEVEL 1 NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX 7.1 HQ Standards 7-22

105 FIRE EXTINGUISHER STIRWELL YOU RE HERE RESTROOMS IN CSE OF EMERGENCY DIL 911 LRM SOUNDS LIKE : RING LRM LOOKS LIKE: FLSHING STROBE IN CSE OF FIRE, USE STIRS FOR EXIT DO NOT USE ELEVTOR Egress Code Sign B15 Dimensions & shapes of all elements as shown on G3.B15a. Panel: Thick acrylic, cut to size. Buff returns smooth and even to eliminate tool marks. Paint all surfaces as indicated. Graphics to be screened first surface. 12 Typography: For Flight Level : Clearview Text Book, 1 Cap Height (Based on E ), Kerned -25%. For Level Indicator: Clearview Text Bold, 1.5 Cap Height (Based on 1 ), Kerned -50%. For Map Key & Warning Information: Clearview Text Book, 0.5 Cap Height (Based on E ), Interline spacing as indicated. For In Case of Fire... : Clearview Text Bold, Cap Height (Based on E ), Kerned 0. Interline spacing as indicated. Panel ll Surfaces P4 Level 1 P5 Level 2 P6 Level 3 P7 Text & Symbols Fire & You re Here Map Staging rea 8.5 x Flight Level001 Map rea CL CL Symbols: (FS): 2.5 Height, (FES): 0.5 Height, (YH): 0.5 Height, (SR): 0.5 Height, (RR): 0.5 Height Map rt: Signage Contractor is responsible for developing LL map layouts, including determination of primary and secondary paths of egress based on Life Safety Plans (1 Series), and is responsible for producing LL digital artwork required to produce signage. Submit LL finished map artwork to Designer for review and approval of map style and content. Submit LL finished map artwork to project Fire Marshall and/or other appropriate governing agency within the project jurisdiction for review and approval for fire code compliance. Provide hard copy of Fire Marshall s signed approval to Owner for record keeping. Refer to G3.MSa for map style guide and minimal requirements for map art. Installation: Concealed 3M VHB tape and silicone mount flush to wall 1 1/2 above existing elevator call button plate. Designer verify and confirm location in field. FIRE EXTINGUISHER YOU RE HERE IN CSE OF EMERGENCY DIL 911 LRM SOUNDS LIKE : RING LRM LOOKS LIKE: FLSHING STROBE IN CSE OF FIRE, USE STIRS FOR EXIT DO NOT USE ELEVTOR STIRWELL RESTROOMS Panel Flight Level001 Map rea 1 Elevation / 3 = Elevation / 1/4 = 1-0 NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX 7.1 HQ Standards 7-23

106 Evacuation Map B16 Dimensions & shapes of all elements as shown on G3.B16a. 11 Holder: Two layers of Colorless Non-Glare crylic w/ crylic spacer. both left and right sides. Configure to hold Insert and removable with Post-It note. Back paint 2nd surface of front layer to create window. Back with spacer and backer. Clear polish returns of front plate only. Buff returns of spacer and backer and paint all surfaces as indicated (Note: Front of backer is paint finished ). Laminate all parts together with concealed full adhesive. 0.5 Spacer B Insert: Clear Rigid cetate with computer printed map art as indicated. Insert to fit flush at sides of opening. Map Staging rea 10 x 9.5 Holder Front Plate Map rt: Signage Contractor is responsible for developing ll map layouts, including determination of primary & secondary paths of egress based on Life Safety plans (1 Series); and, is responsible for producing LL digital and/or hard copy camera-ready artwork required to produce signage. Submit LL finished map artwork to Designer for design intent review & submit to project Fire Marshall and/or other appropriate governing agency within the project jurisdication for review & approval for fire code compliance. Provide hard copy of Fire Marshall s signed approval to Owner, Designer & rchitect for record keeping. Designer to provide map style guide w/ list of minimum requrements, sign location plans ONLY. 11 Backer Installation: Concealed VHB tape & silicone mount flush to wall. Locate 56 from center of sign to finished floor. Designer / Fire Marshall to confirm mounting location of extra stock as required. B Insert 11 x Elevation / Half Size Side View / Half Size 1 2 NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX 7.1 HQ Standards 7-24

107 Stairwell Graphic B17 Dimensions & shapes of all elements as shown on G3.B17a. lign Cut Letters: Computer Cut 0.25 aluminum letters. Grind and buff smooth to eliminate any tooling marks. Paint all surfaces as indicated. Typography: For Flight Level, Clearview Text Book. For Level, Clearview Text Bold. Sized as indicated. Installation: Concealed 3M VHB tape & silicone mount flush to wall. locate as indicated. Cut Letters ll Surfaces 003 FLIGHT LEVEL 001 FLIGHT LEVEL 002 FLIGHT LEVEL Cut Letters 003 FLIGHT LEVEL 1 Elevation / 1/2 = Elevation / 3/16 = 1-0 NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a This record contains Sensitive Security Information that is controlled under 49 CFR parts 7.1 HQ Standards

108 Fire Extinguisher Sign 18 Dimensions & shapes of all elements as shown on G3.G18a. Panel: crylic Plaque of thickness. Cut to size and buff returns smooth and even to eliminate tooling marks. Paint finish all surfaces as indicated. screen print graphics at first surface. Installation: Concealed VHB tape & silicone mount holder assembly flush to wall. Locate on wall, 4 above Fire Extinguisher Cabinet. Owner to field verify position. 9 CL Panel CL 4 Panel P7 ll Surfaces Symbol CL 9 1 Elevation / Half Size Schematic 2 Elevation / 1/2 = 1-0 NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a This record contains Sensitive Security Information that is controlled under 49 CFR parts 7.1 HQ Standards

109 Lectern Logo 19 Dimensions & shapes of all elements as shown on G3.B19a. Panel: crylic of 0.25 thickness, cut to size. Buff returns smooth and even to eliminate any tooling marks. Paint all surfaces as indicated and direct image gradient logo to first surface. Installation: Concealed VHB tape and silicone mount flush to lecturn. Locate as indicated. CL Podium to be provided by others Panel 5 & 6 Gradient Background Text & Wave 3 Returns 9 3 Panel CL 1 Elevation / 3 = Elevation / 3/4 = 1-0 NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a This record contains Sensitive Security Information that is controlled under 49 CFR parts 7.1 HQ Standards

110 Board Room Name Sign 20 Dimensions & shapes of all elements as shown on G3.B20a. Desk (by Others) Sign ssembly Panel: Stainless steel panel of thickness to be cut to shape. Buff edges smooth and even to eliminate any tooling marks. Roll face to match radius as indicated. Finish all surfaces as indicated. Name to be screen printed to first surface, color as indicated. Typography: Clearview Text Bold, 1.25 Cap Height (Based on E ), Kerned 0. Installation: Sign asssembly to be mounted to board member desk via incorporated mounting tabs and lip in desk. Sign Contractor responsible to field verify all as-built condidtions prior to fabrication. Mounting Tab Panel R 10-1 (V.I.F.) Top View / 3 = 1-0 Mounting Detail / 3 = Panel M4 ll Surfaces 3 Text 20 CL Francisco Hernandez Mounting Tab Panel Elevation / 3 = 1-0 Side View / NTS 1 2 NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX 7.1 HQ Standards 7-28

111 Panel (Face) Panel (Side) lign - Tight Seam Directional Pylon Dimensions & shapes of all elements as shown on G3.E2a. E2 Panel: Four panels required per location. luminum Panel of not less than thickness. Cut to size and buff returns smooth and even to eliminate tooling marks. Paint finish all surfaces as indicated. pply 3M Computer Cut Vinyl Graphics to first surface. Screen print logo to first surface as indicated. Panel Face Sides Logo & Rule V2 Text & rrow Rule DFW irport Headquarters Visitors CL 3-6 Panel 3 Top View / 1 1/2 = Typography: Clearview Hwy 4-W, 2.5 Cap Height (Based on E ), Kerned -50%. Interline spacing of 6. For DFW irport Headquarters Clearview Hwy 3-W, 2 Cap Height (Based on E ), Kerned 0. Interline spacing at 3.5 Symbols: rrow: 3 Length; Logo: 6 Height; Rule = 0.25 thickness B Base: Cast in Place Smooth Finish Concrete, refer to rchitect s specifications for concrete requirements to follow. C Footing: Single unit smooth finish concrete and rebar footing, sized and configured to support sign assembly plumb and level. Integrated smooth finish mow strip, sized as indicated. Employment Installation: Concealed 3M VHB ape and construction adhesive flush to concrete base. lign Edges. Deliveries Reveal 0.5 Reveal 0.5 B Base 1-6 B Base Mow Strip C Footing Footing Elevation / 1 1/2 = 1-0 Side View / 1 1/2 = C NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a This record contains Sensitive Security Information that is controlled under 49 CFR parts 7.1 HQ Standards

112 DOT/ Reserved Parking Identity E3 Dimensions & shapes of all elements as shown on G3.E3a thru G3.E3b. Panel ll Surfaces V9 Symbol V8 Text and Rule TYP. 12 CL Radius = 1 Panel ll Surfaces V9 Fuel Efficient Vehicle Text V8 Symbol & Text CL FUEL EFFICIENT VEHICLE Panel: luminum Panel of thickness. Cut to shape and buff returns smooth and even to eliminate tooling marks. pply 3M Computer Cut Vinyl Graphics to first surface. Mount to post - post to be provided by others. Reference rchitectural Documents for post details. Typography For Reserved Parking, Clearview Hwy 2-W, 1.75 Cap Height (Based on E ), Interline Spacing of 2.5. For Tow-way and Van, Clearview Hwy 2-B, 1.5 Cap Height (Based on E ). For Zone and ccessible, Clearview Hwy 5-W, 1 Cap Height (Based on E ). Symbols: (HC) = 8 height; Fuel Efficient Car = 5 Height Rule = 0.25 thickness Installation: Direct Burial of Post and Panel assembly securely, level and plumb in below grade concrete footing. For softscape locations, back fill with soil and resod or match existing landscape materials. For hardscape locations, core drill and smooth concrete flush with surrounding surfaces. Sign contractor responsible to field verify all as build conditions to determine hardscape or softscape. RESERVED PRKING TOW-WY ZONE TYP. CL VN CCESSIBLE RESERVED PRKING TOW-WY ZONE Panel ll Surfaces V8 Text & Rule Elevation / 3 = 1-0 Elevation / 3 = 1-0 Elevation / 3 = NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a This record contains Sensitive Security Information that is controlled under 49 CFR parts 7.1 HQ Standards

113 12 CL Post (By Others) DOT/ Reserved Parking Identity Dimensions & shapes of all elements as shown on G3.E3a thru G3.E3b. E3 U-Bolt Hardware & Mount 11 Panel Top View / Half Size Panel ll Surfaces V5 Circle Symbol Text and Rule V6 P Symbol NO STOPPING STNDING PRKING TOW-WY ZONE CL 30 CL Panel Post (by others) NO STOPPING STNDING PRKING TOW-WY ZONE 84 Panel Post (by others) RESERVED PRKING TOW-WY ZONE VN CCESSIBLE 84 1 Elevation / 3 = 1-0 Elevation / 1/2 = NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX 7.1 HQ Standards 7-31

114 ddress Identity E4 Dimensions & shapes of all elements as shown on G3.E4a Cut Letters 3 ll Surfaces 2 Elevation / 1 = Cut Letters: Computer cut letters of 0.25 thick aluminum. Buff returns smooth and even to elimnate any tooling marks. Drill and tap reverse of each element for not less than 3 studs per element. Paint finish all surfaces as indicated. Typography: Clearview Hwy 5-W, Sized as indicated, Kerned -100% Installation: Concealed stud and silicone mount flush to wall surface. Seal all penetrations 360 degrees with a sealant approved by General Contractor. Designer will field locate exact installation location. Sign Contractor is responsible for field verifying all as-built conditions including building dimensions and indicate on shop drawings for review and approval. 12 Cut Letters Elevation / 1/16 = 1-0 DFW International irport Headquaters Exterior, Garage & Interior Graphic Elements DFW International irport Headquarters Mark Description Date NOTE: Taken from DFW International irport Headquarters document dated March 17, 2014 Project No.: Package 5.6: March PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a 1909 Woodall Rodgers Fwy. Suite E irfield Dr Dallas, TX Series G3.00 DFW irport, TX t: Design Intent Documents 7.1 HQ Standards 7-32

115 Entry / Exit Identity G1 Dimensions & shapes of all elements as shown on G3.G1a. Cut Letters 3 ll Surfaces Exit Only 9 Cut Letters 3 ll Surfaces Employee Garage Entrance Elevation / 3/4 = Elevation / 3/4 = 1-0 Exit Only Employee Garage Entrance 16 Cut Letters: Computer cut letters of 0.25 thick aluminum. Buff returns smooth and even to elimnate any tooling marks. Drill and tap reverse of each element for not less than 3 studs per element. Paint finish all surfaces as indicated. Typography: Clearview Hwy 5-W, Sized as indicated, Kerned -100% Installation: Concealed stud and silicone mount flush to wall surface. Seal all penetrations 360 degrees with a sealant approved by General Contractor. Designer will field locate exact installation location..... Cut Letters 1 Elevation / 1/4 = 1-0 NOTE: Taken from DFW International irport Headquarters document dated March 17, PPENDIX Issue Date: These documents are intended to illustrate design intent, and should only be used as a This record contains Sensitive Security Information that is controlled under 49 CFR parts 7.1 HQ Standards