SECTION SITE FURNISHINGS FOR CFCRT. 1. American Society for Testing and Materials (ASTM).
|
|
- Derek Daniels
- 5 years ago
- Views:
Transcription
1 PART 1 - GENERAL 1.1 SECTION INCLUDES A. Benches. B. Trash receptacles. C. Bike storage. 1.2 REFERENCE STANDARDS A. Including but not limited to: 1. American Society for Testing and Materials (ASTM). 1.3 REFERENCES A. Submit certifications for all materials incorporated in the Work. B. Product Data: Manufacturer s descriptive literature for specified products, including: 1. Preparation instructions and recommendations. 2. Storage and handling requirements/recommendations. 3. Installation methods. C. Shop Drawings: Complete details of layout and assembly, showing member sizes and part identification, fasteners, anchors, and fittings. D. Selection Samples: Two sets of color chips representing manufacturer s full range of available colors. E. Manufacturer s warranties. 1.4 QUALITY CONTROL A. Quality Control shall be by the Contractor and as required by the Contractor's Quality Plan and applicable Reference Standards. 1.5 PROJECT CONDITIONS A. Do not install products under environmental conditions outside manufacturer's absolute limits. PART 2 - PRODUCTS 2.1 PRODUCT DELIVERY, STORAGE AND HANDLING A. Deliver products in good condition. Page 1 of 8
2 B. Store products in manufacturer's unopened packaging until ready for installation to prevent corrosion, deterioration and damage. C. Handle products with care to prevent damage. D. Storage: Store materials in a clean, dry area indoors out of the elements.\ 2.2 BENCHES A. Bench B-1 (see Plans): 1. The bench shall have the following characteristics: a. Steel bench with backrest. b. Welded seat and back. c. End frames: Cast iron bench supports with curved armrests. Each support shall have (2) integral mounting brackets at base. d. Center arm rest: Cast iron to match end frame style. e. Seat: 1/4 inch by 1-1/2 inch steel bars and 2-3/8 inch O.D. steel pipe. Back and seat to be one-piece continuous bars. The ends of the bars at each end shall curve around steel pipe. f. Fasteners: Stainless steel. g. Bracing: 1-1/16 inch O.D. steel pipe. h. Seat height: 17-1/16 inches. i. Width: 27-9/16 inches. j. Length: 6 feet. k. Mounting: Provide with 1/2 inch by 3-3/4 inch zinc plated anchor bolts. l. Finish: (2) Blast: Sandblast to a white finish. (3) Wash: Multiple stage wash system. (4) Primer: Zinc-rich primer. (5) Topcoat: Colored UV resistant polyester powder. (6) Curing: Oven cure for a minimum of twenty minutes to produce an average minimum film thickness of 3 mils. m. Refer to and follow manufacturer s specifications. a. Limited twenty-year warranty following the date of Final Acceptance against structural failure of all steel bench frames or complete steel bench assemblies. b. Limited twenty-year warranty following the date of Final Acceptance against structural failure of all cast iron bench supports. B. Bench B-2 (see Plans): 1. The bench shall have the following characteristics: a. Steel bench with backrest. b. Welded seat and back. c. Steel seat and back panels: 10 gauge HRPO steel with plasma cut grass design. d. Fasteners: Seat panels to attach to frame with stainless steel hardware. Page 2 of 8
3 e. End frames and armrests: 1/4 inch by 3 inch flat bar steel frame bolted together with stainless steel hardware. f. Bench frame: 1/4 inch thick steel angles welded to end frames. g. Seat height: 17 inches. h. Back height: 35-1/4 inches. i. Width: 24-1/2 inches. j. Length: 67 inches. k. Mounting: Each leg shall have tabs for surface mounting with corrosion resistant anchor bolts. l. Finish: (2) Preparation and cleaning: (a) Brush, grind, fill or sandblast welded parts to remove carbon and prepare metal for cleaning and pre-treatment. (b) Clean using a heated wash to degrease and remove surface oils. (c) Apply zinc-phosphate pre-treatment. (3) Undercoat: (a) Apply oven-cured epoxy undercoat. (4) Finish: (a) Apply two coats of powdercoat, with oven-curing after each application. (b) Apply topcoat and oven cure to produce a minimum film thickness of 4 mils. m. Refer to and follow manufacturer s specifications. a. Limited three-year warranty following the date of Final Acceptance against defect in C. Bench B-3 (see Plans): 1. The bench shall have the following characteristics: a. Steel bench with backrest. b. Welded seat and back. c. End frames: Two cast iron end bench supports with curved armrests. Each support shall have two 9/16-inch diameter pre-drilled holes for surface mounting. d. Center arm rest: Cast iron to match end frame style (does not extend beneath bench seat). e. Seat and Backrest: Horizontal 1/4 inch by 1-1/2 inch steel bars welded to four 1/2- inch thick steel plates (one at each end and two intermediate). 1-1/2 schedule 40 steel pipe at top of back and front of seat that connect to end frames with ½ x 2-1/2 stainless steel screws. Back and seat to be one-piece. f. Fasteners: Stainless steel. g. Seat height: 16-11/16 inches. h. Back height: 32 inches. i. Width: 27-5/16 inches. j. Length: 73 inches. Page 3 of 8
4 k. Mounting: Surface mount through pre-drilled holes using 1/2 inch by 3-3/4 inch zinc plated anchor bolts. l. Finish: (2) Blast: Sandblast to a white finish. (3) Wash: Multiple stage wash system. (4) Primer: Zinc-rich primer. (5) Topcoat: Colored UV resistant polyester powder. (6) Curing: Oven cure for a minimum of twenty minutes to produce an average minimum film thickness of 3 mils. m. Refer to and follow manufacturer s specifications. a. Limited twenty-year warranty following the date of Final Acceptance against structural failure of all steel bench frames or complete steel bench assemblies. b. Limited twenty-year warranty following the date of Final Acceptance against structural failure of all cast iron bench supports. D. Bench B-4 (see Plans): 1. The bench shall have the following characteristics: a. Steel bench with backrest and one center divider. b. Steel seat and back panels: Panels are thick ASTM A 1011 hot rolled pickled and oiled commercial steel type B, formed. Seat and back panels are bolted to end frames. Seat panels have a perforation pattern. Back panels are solid. c. End frames, armrests, and seat dividers: Type 319 ASTM B 26 aluminum sand castings. d. Seat height: 16-1/2 inches. e. Back height: 39 inches. f. Arm height: 24-3/8 inches. g. Width: 27-1/2 inches. h. Length: 77-1/2 inches. i. Mounting: Surface mounting Use threaded anchor bolts, threaded set screws, and anchoring adhesive. Refer to and follow manufacturer s specifications. j. Fasteners: All threaded fasteners are to be stainless steel. k. Finish: (2) Preparation and cleaning: (a) Brush, grind, fill or sandblast welded parts to remove carbon and prepare metal for cleaning and pre-treatment. (b) Clean using a heated wash to degrease and remove surface oils. (c) Apply zinc-phosphate pre-treatment. (3) Undercoat: (a) Apply oven-cured epoxy undercoat. (4) Finish: (a) Apply two coats of powder coat, with oven-curing after each application. Page 4 of 8
5 (b) Apply topcoat and oven cure to produce a minimum film thickness of 4 mils. l. Refer to and follow manufacturer s specifications. a. Limited three-year warranty following the date of Final Acceptance against defect in 2.3 TRASH RECEPTACLES A. Trash receptacles TR-1 (see Plans): 1. The trash receptacle shall have the following characteristics: a. Welded trash receptacle. b. Mounting: Surface mount through integral tabs using non-corrosive hardware. c. Perforated metal sides: 11 gauge HRPO steel with 2 inch square holes, 1/4 inch radius corners, and minimum 2 inch square solid metal border. d. Lid: Fixed dome type lid of 11 gauge spun steel with minimum spin lines, 16-3/4 inch diameter with (2) 5 inch by 10-3/4 inch side openings. e. Liner: Linear low-density polyethylene of.100 inch nominal thickness with (8) large openings for clear visibility to trash within. f. Diameter: 16-3/4 inches. g. Height: 31-7/8 inches. h. Opening: Side opening with hinged door. i. Capacity: 30 gallon. j. Finish: (2) Preparation and cleaning: (a) Brush, grind, fill or sandblast welded parts to remove carbon and prepare metal for cleaning and pre-treatment. (b) Clean using a heated wash to degrease and remove surface oils. (c) Apply zinc-phosphate pre-treatment. (3) Undercoat: (a) Apply oven-cured epoxy undercoat. (4) Finish: (a) Apply two coats of powder coat, with oven-curing after each application. (b) Apply topcoat and oven cure to produce a minimum film thickness of 4 mils. k. Refer to and follow manufacturer s specifications. a. Limited three-year warranty following the date of Final Acceptance against defect in B. Trash receptacles TR-2 (see Plans): Page 5 of 8
6 1. The trash receptacle shall have the following characteristics: a. Welded trash receptacle. b. Mounting: Surface mount through integral tabs using non-corrosive hardware. c. Sides: 1-inch wide vertical straps of 11 gauge HRPO steel with 2-inch wide gaps between straps, and 1-inch solid metal border at top and bottom. d. Lid: Fixed dome type lid of 11 gauge spun steel with minimum spin lines, 20-1/2 inch diameter with (4) 6-inch by 11- inch side openings. e. Liner: Linear low-density polyethylene of.100 inch nominal thickness with (8) large openings for clear visibility to trash within. f. Diameter: 20-1/2 inches. g. Height: 42 inches. h. Opening: Side opening with hinged door and latch. i. Capacity: 30 gallon. j. Finish: (2) Preparation and cleaning: (a) Brush, grind, fill or sandblast welded parts to remove carbon and prepare metal for cleaning and pre-treatment. (b) Clean using a heated wash to degrease and remove surface oils. (c) Apply zinc-phosphate pre-treatment. (3) Undercoat: (a) Apply oven-cured epoxy undercoat. (4) Finish: (a) Apply two coats of powder coat, with oven-curing after each application. (b) Apply topcoat and oven cure to produce a minimum film thickness of 4 mils. k. Refer to and follow manufacturer s specifications. 2.4 BIKE STORAGE a. Limited three-year warranty following the date of Final Acceptance against defect in A. Bike Rack BR-1 (see Plans): 1. The bike rack shall have the following characteristics: a. Welded bike rack to accommodate two bikes. b. Center Post: 2 inch schedule 40 steel pipe. c. Ring: 1-1/2 inch O.D. 11 gauge steel tube. d. Mounting: Embedded in concrete per manufacturer s specifications. e. Overall height: 44 inches (10 inches embedded). f. Width: 16-1/2 inches g. Finish: (2) Blast: Sandblast to a white finish Page 6 of 8
7 (3) Wash: Multiple stage wash system. (4) Primer: Epoxy primer electrostatically applied. (5) Topcoat: Colored UV resistant polyester powder. (6) Curing: Oven cure for a minimum of twenty minutes to produce a minimum film thickness of 6 mils. PART 3 - EXECUTION 3.1 EXAMINATION a. Limited one-year warranty following the date of Final Acceptance against defect in A. Examine surfaces to receive site furnishings. Notify Engineer of conditions that would adversely affect installation or subsequent utilization of site furnishings. Do not proceed with installation until unsatisfactory conditions are corrected. 3.2 FABRICATION AND FORMING A. General: Verify dimensions before proceeding with Work. Verify measurements at site. B. Coordinate finishes and colors with other Work. Obtain acceptance from the Engineer prior to fabrication. 3.3 PREPARATION A. Clean surfaces of all products thoroughly prior to installation. B. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions. C. Ensure surfaces to receive site furnishings are clean, flat, and level. 3.4 INSTALLATION A. Install in accordance with manufacturer's instructions, and using the installation method described in the Plans and at locations indicated on the Plans. B. Install site furnishings level, plumb, square, accurately aligned, correctly located, and without warp. C. Embedded mounting: Place those site furnishings specified to be embedded by direct burying in accordance with manufacturer s instructions and the Plans. D. Surface mounting: Place those site furnishings specified to be surface mounted in accordance with manufacturer s instructions and the Plans. E. Repair minor damages to finish in accordance with manufacturer s instructions and as approved by Engineer. Page 7 of 8
8 F. Remove and replace damaged components that cannot be successfully repaired as determined by Engineer. 3.5 PROTECTION A. Protect installed products until completion of project. 3.6 CLEANING A. Clean up debris, trash, and unused material, and remove from site. END OF Page 8 of 8
LITTER RECEPTACLE; (5) at Bus Stops; (Park receptacles excluded at this time) Style: Reading Size: 32 GALLON: 28 W; 33 1/2 H Cost: $840
AMBRIDGE STREETSCAPE: SITE FURNISHINGS RECOMMENDATIONS HANCOCK ARCHITECTURE, ROCHESTER, PA 8-9-17 MANUFACTURER: KEYSTONE RIDGE, BUTLER, PA All products are available in various options and have the capability
More informationTesting. Material testing will be according to applicable AASHTO, ASTM or Department methods as specified.
907.01 Section 907. FENCING MATERIALS 907.01 General Requirements. Materials for use in fencing property, right-of-way and other installations must comply with this section. 907.02 Testing. Material testing
More informationSECTION CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP
1 1 1 0 1 0 1 0 1 SECTION 1 1 CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP BASED ON DFD MASTER SPECIFICATION DATED /01/ P A R T 1 - G E N E R A L SCOPE The work under this section shall consist of
More informationSECTION METAL FABRICATIONS
SECTION 05100 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for metal fabrications, including minimum requirements for fabricator, and galvanizing. 1.02 REFERENCE STANDARDS A. ASTM
More informationVersai Evolution of Versatile Fencing
Versai Evolution of Versatile Fencing About Versai Ornamental Fencing Versai Ornamental Fencing Versai Ornamental Fencing by Fortress is the next generation in ornamental fencing. It offers a solution
More informationC. Samples for Initial Selection: Manufacturer's color charts showing the full range of colors available.
SECTION 105113 - METAL LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION BULLET- RESISTANT DOORS
1 SECTION 08 3950 BULLET- RESISTANT DOORS PART 1- GENERAL 1.01 SUMMARY A. This Section Includes: 1. Bullet- resistant steel door and frame systems. 2. Door hardware for bullet- resistant steel door and
More informationEMMEGI ARCHITECTURAL FENCING MASTER SPECIFICATION SECTION METAL FENCING, GATES & RAILING SYSTEM PART 1 GENERAL
EMMEGI ARCHITECTURAL FENCING MASTER SPECIFICATION SECTION 05720 METAL FENCING, GATES & RAILING SYSTEM PART 1 GENERAL EMMEGI ARCHITECTURAL FENCING is a high quality steel fencing system comprised of a hybrid
More informationUP4 LEARN-A-LOT (PLAYFUL) Parts List DESCRIPTION 90 ANGLE BRACKET DOOR WINDOW MUSIC CATERPILLAR CIRCLE FRAME CIRCLE MIRROR YELLOW STAINED GLASS RED STAINED GLASS SQUARE TRIANGLE SPIRAL WHEEL SQUARE MIRROR
More informationUP43 LEARN-A-L0T (NATURAL) Parts List DESCRIPTION 90 ANGLE BRACKET DOOR WINDOW MUSIC CATERPILLAR CIRCLE FRAME CIRCLE MIRROR YELLOW STAINED GLASS RED STAINED GLASS SQUARE TRIANGLE SPIRAL WHEEL SQUARE MIRROR
More informationDENVER PUBLIC SCHOOLS DESIGN AND CONSTRUCTION STANDARDS This Standard is for guidance only. SECTION METAL LOCKERS
PART 0 A/E INSTRUCTIONS 0.01 GENERAL DESIGN REQUIREMENTS A. Architect shall coordinate with the DPS Project Manager the type, layout and size of lockers required on the project. B. Varsity athletic Lockers
More informationProduct Guide Specification
Shield Casework February 2014 3421 Merriam Lane Overland Park, Kansas 66203 Phone 913-744-2183 Fax 913-384-3477 Website www.shieldcasework.com E-mail info@shieldcasework.com Product Guide Specification
More informationDesign and Construction Standards SECTION ATHLETIC LOCKERS
SECTION 10505 ATHLETIC LOCKERS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. The provisions of the General Conditions, Supplementary Conditions, and the Sections included under Division 1, General Requirements,
More informationCITY OF PITTSBURG ENGINEERING DEPARTMENT CONTRACT NO A WATER TREATEMENT PLANT CAPITAL IMPROVEMENTS PHASE 1A ADDENDUM #1 FENCE AND DITCH AUGUST
CITY OF PITTSBURG ENGINEERING DEPARTMENT CONTRACT NO. 2012-16A WATER TREATEMENT PLANT CAPITAL IMPROVEMENTS PHASE 1A ADDENDUM #1 FENCE AND DITCH AUGUST 2014 CHAIN LINK FENCE SPECIFICATIONS Chain link fence,
More informationUP139 CRUISE-A-LONG (STANDARD) NATURAL COATED DECK COATED RAMP DESCRIPTION SQUIRREL PANEL BACK WALL CLEAR BUBBLE CRUISE RAIL SQUARE SPIRAL WHEEL 90 AN
UP39 CRUISE-A-LONG (STANDARD) NATURAL COATED DECK COATED RAMP DESCRIPTION SQUIRREL PANEL BACK WALL CLEAR BUBBLE CRUISE RAIL SQUARE SPIRAL WHEEL 90 ANGLE BRACKET TUBE BRACKET TUBE WARNING LABEL PLATE HARDWARE
More informationItem 550 Chain Link Fence
Item Chain Link Fence 1. DESCRIPTION 2. MATERIALS Furnish, install, remove, repair, or replace chain link fence and gates. Furnish certification from the chain link fence materials manufacturer stating
More informationNext Level Security. This 2-tier locker ships flat to save on freight, comes in galvanized and powder coat finish options, and has a modular design.
T WO - T I E R B IK E LO C K E R Next Level Security We take long-term bicycle storage to new heights with the new Dero Two-Tier Bike Locker. It is easy to load and provides a space-saving solution to
More informationBike Locker Model DBL1 & DBL2
Bike Locker Model DBL1 & DBL2 DBL1 & DBL2 are constructed of 99% recycled steel and is available in 20 standard powder coat colors or a galvanized finish. DBL1 & DBL2 store 1 or 2 bikes effortlessly and
More informationH O O P RAC K. Simple Security
H O O P RAC K Simple Security The Hoop Rack is a proven design that provides high security and easy bike parking. The Hoop Rack uses thick pipe construction and the full radius of the bend makes the Hoop
More informationUP133 CRAWL & TODDLE (STANDARD) NATURAL COATED DECK COATED RAMP FRONT WALL BACK WALL DESCRIPTION COATED STEPS 90 ANGLE BRACKET LEFT WALL RIGHT WALL CL
UP33 CRAWL & TODDLE (STANDARD) NATURAL COATED DECK COATED RAMP FRONT WALL BACK WALL DESCRIPTION COATED STEPS 90 ANGLE BRACKET LEFT WALL RIGHT WALL CLEAR BUBBLE CRUISE RAIL SQUARE SPIRAL WHEEL TRIANGLE
More informationdesignmasterfence.com
designmasterfence.com > INDEX > WHAT IS DESIGNMASTER? > PRODUCTS APPLICATIONS 2 3 > CLASSIC FENCE PANEL Specs & Advantages > CLASSIC FENCE POST Specs, Advantages & Installation > BRACKETS & ACCESSORIES
More information5/16" Flange nut. Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc plated bolt w/ washers and nut. Anchor 3" sq. 7 Ga.
2 1/2" x 2 1/2" x 10 Ga. 6" 5" 4" Variable Slipbase (8" Sq. SYS.) 5/16 Corner Bolt W/ nut 5/16" Flange nut Stub Insert (8" Sq. SYS.) Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc
More informationCity of Regina Standard Construction Specification SECTION 2660 CHAIN LINK FENCE
1.0 GENERAL 1.1 Scope 1.1.1 The work shall consist of supply and installing chain link fence, including braces and gates, as shown on the plans and specifications at the locations designated by the Engineer.
More informationULT R A S PACE SAV E R SQ UA R E D
ULT R A S PACE SAV E R SQ UA R E D Hip to be Square Dero s Ultra Space Saver Squared offers high-security, vertical bike parking. Adjustable sliding arms make it easy for customers to best utilize their
More informationDERO BIKE LOCKER 33. Maximum Security
Maximum Security The Dero Bike Locker 33 offers bike parking for a single bicycle per unit, thus providing a narrower footprint when space is limited. This affordable bike locker is a perfect option for
More informationTENANT IMPROVEMENT 16 FEBRUARY WEST 27TH STREET, 4TH FLOOR 100% CD OWNER/BID ADD 1-03/08/2018
SECTION 055000 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationAPPENDIX FENCE GENERAL NOTES
APPENDIX FENCE GENERAL NOTES 1. Fabric: 9 gage, 2" mesh, knuckle top and bottom, placed on the outside of posts, single fabric width for the entire height. 2. All fencing to be standard galvanized finish.
More information.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1.
PAGE 1 PART 1 GENERAL 1.1 REFERENCE.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. 1.2 RELATED WORK SPECIFIED ELSEWHERE.1 Installation
More informationH O O P RAC K. Simple Security
H O O P RAC K Simple Security The Hoop Rack is a proven design that provides high security and easy bike parking. The Hoop Rack uses thick pipe construction and the full radius of the bend makes the Hoop
More informationMANUFACTURING INC. Specifications
Page 1 of 4 GENERAL 11 Aluminum security screen doors must be tested by a recognized testing laboratory to conform to SMA 6001-2002 Proposed American National Standard Specifications for Metal Protection
More informationS W E RV E RAC K. Simple Security. Simple Stability.
S W E RV E RAC K Simple Security. Simple Stability. The Swerve Rack is a proven design that provides high security and easy bike parking. The Swerve Rack uses thick pipe construction and the full radius
More informationSECTION HOLLOW METAL DOORS AND FRAMES
SECTION 081113 HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: Include construction details, material
More informationProduct Guide Specification
HALFEN USA Inc. March 2012 8521 FM 1976 P.O. Box 547 Converse, TX 78109 Toll Free 800-423-9140 Fax 888-277-1695 Website www.halfenusa.com E-mail info@halfenusa.com Product Guide Specification Specifier
More informationB. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.
SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.
More information1.1 SUMMARY. A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards.
PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards. B. See Division 5 Section "Pipe and Tube Railings"
More informationTO O L K IT. Public Bike Repair
TO O L K IT Public Bike Repair The Dero Tool Kit includes all the necessary tools to perform most routine maintenance and adjustments on most bikes. All the tools are securely fastened with stainless steel
More informationB. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.
SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.
More informationCYCL E STAT IO N. High Capacity
CYCL E STAT IO N High Capacity The Dero Cycle Station provides high-capacity, covered bike parking for bicycle commuters. With a high roof and open platform, the Dero Cycle Station allows bike corrals,
More informationSECTION TRAFFIC SIGNAGE
SECTION 10 14 53 TRAFFIC SIGNAGE PART 1 - GENERAL 1.01 SECTION INCLUDES A. Furnishing and installing roadside traffic signage. B. Providing additional traffic signs as required in Sections 01 55 28 Controlling
More informationA. Columns: Worthington Millwork; Cellular Polyvinyl Chloride (PVC) columns; decorative, weatherproof, insect-proof, and highly durable.
WorthingtonWrap PVC Columns Architectural Specifications 1.1 SECTION INCLUDES A. Columns: Worthington Millwork; Cellular Polyvinyl Chloride (PVC) columns; decorative, weatherproof, insect-proof, and highly
More informationUNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-10 51 13 (May 2011) ------------------------- Preparing Activity: NAVFAC Superseding UFGS-10 51 13 (July 2007) UNIFIED FACILITIES GUIDE SPECIFICATIONS References are
More informationC. HMMA 863: Guide Specifications for Detention Security Hollow Metal Doors and Frames
SECTION 083463 DETENTION DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationPART MATERIALS. Section Fencing Materials. Description
PART 03000 - MATERIALS Section 03010 - Fencing Materials Description 03010.00 Scope - This section consists of the test requirements, specifications and tolerances for barbed wire, woven wire and chain
More informationALUMINUM PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Structural Tube, Pipe and Bar shall be in accordance with ASTM B22 or ASTM B429, Alloy 606-T6. End Rail 90 bends and corner bends with maximum 4-0" post spacing, may be Alloy
More informationSTEEL PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Pipe Rails and s shall be in accordance with ASTM A5 Grade B for standard weight pipe and ASTM A500 Grade B, C or D or ASTM A50 for structural tube. Bars for handrail supports
More informationADJUSTABLE MOUNTING POST
C Part Number 069 B EACH CARTON CONTAINS D Floor Mounting Kit A. Bottom Post Assembly B. Top Post Assembly C. Flange Head Bolts (x2) D. Floor Mounting Kit. 5/8 Wx/6 Hx0 L framing channels (x2) 2. /8-6x4
More informationH HD Adult Wheelchair Swing Frame & Hangers(perm) IMPORTANT
Page 1 IMPORTANT PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be installed in accordance with these instructions. Check your shipment against Bill of Lading and Parts list.
More informationULT R A SPAC E SAV E R
ULT R A SPAC E SAV E R Double Capacity, Modular Construction The Ultra Space Saver provides easy and ample space for u-lock security on nearly any bike, including bikes with fenders. Thanks to design enhancements,
More informationProject: # Solano Community College District
ADDENDUM #02 Project: #16 007 Solano Community College District Horticulture Site Improvements Date: April 26, 2016 The following clarifications are provided based on questions received or changes in District
More informationSECTION CABLE TRAYS FOR COMMUNICATIONS SYSTEMS
SECTION 270536 - CABLE TRAYS FOR COMMUNICATIONS SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSECTION HOLLOW METAL DOORS AND FRAMES
PART 1 GENERAL 1.01 SECTION INCLUDES SECTION 08 11 13 HOLLOW METAL DOORS AND A. Non-fire-rated hollow metal doors and frames. B. Hollow metal frames for wood doors. C. Fire-rated hollow metal doors and
More informationOSE Submittal July 20, 2018
SECTION 055000 - METAL FABRICATIONS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION IDENTIFICATION FOR FIRE SUPPRESSION PIPING AND EQUIPMENT
SECTION 21 05 53 IDENTIFICATION FOR FIRE SUPPRESSION PIPING AND EQUIPMENT Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2015-2015 ARCAT, Inc. - All rights reserved PART 1 GENERAL
More informationToll-Free
Primary applications for Ross DS Series Security Doors and Frames include government, industrial, commercial and residential properties where protection of people and property is of utmost concern and
More informationKO LO SH E LT E R. High Capacity and Flexibility
KO LO SH E LT E R High Capacity and Flexibility The unique styling of our redesigned Dero Kolo Shelter will help beautify your facility and provide secure, covered bike parking for cyclists. The Kolo is
More informationSECTION ROOF ACCESSORIES. Display hidden notes to specifier. (Don't know how? Click Here)
SECTION 07720 ROOF ACCESSORIES PART 1 GENERAL 1.1 SECTION INCLUDES Display hidden notes to specifier. (Don't know how? Click Here) A. Attachment clamp system for standing seam metal roofs. B. Attachment
More informationSECTION STRUCTURAL STEEL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 05 12 00 - STRUCTURAL STEEL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION STRUCTURAL STEEL. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.
SECTION 051200 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting
More informationA. Extent of structural precast concrete work is shown on drawings and in schedules.
SECTION 03 41 00 - STRUCTURAL PRECAST CONCRETE PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 specification
More informationSecure Bike Parking. Patent Pending Dero
VE LO P O RT Secure Bike Parking The graceful lines and modern laser-cut design makes the Veloport stand out while still offering the security and durability you need in your long-term bike parking. Each
More informationMETAL METAL
12654 - METAL 12654-1 PART ONE: GENERAL METAL 1.1 Architectural metals shall be of the best commercial quality and their various forms shall be straight and true. There shall be no scratches, scars or
More informationStorage and Installation of welded LL Hollow Metal Door Frames in Steel Studs
Storage and Installation of welded LL Hollow Metal Door Frames in Steel Studs Introduction This guide specification is intended to stress the necessary precautions and requirements for receipt, storage,
More informationGENERAL ISOMETRIC LAYOUT
EXISTING OR PROPOSED WIPER WALL SUPPORT STRUCTURE GATE LID CARBATHAN HG 0 WEB GRAY LOWER PAN GRATING ALUMINUM WIPER WALL CARBATHANE HG, 90 GRAY STRUCTURAL SPECIFICATIONS:. FLOODGATE MATERIAL TO BE ALUMINUM
More informationSwerve Rack CUSTOM RACKS AVAILABLE
CUSTOM RACKS AVAILABLE Swerve Rack The design of the Swerve mirrors the bike frame, thus providing superior bike support while making it easy to secure both the bike frame and wheel with a standard u-lock.
More informationSECTION STEEL LIGHTING STANDARDS. 1. Electrical conduit and fittings; Section
02760-1 of 5 SECTION 02760 STEEL LIGHTING STANDARDS 02760.01 GENERAL A. Description Steel lighting standards shall include, but not necessarily be limited to, furnishing and installing steel lighting poles,
More informationBol FEATURES: SPECIFICATIONS: 8' 24' Round Tapered and Straight Wood Poles STRUCTURA INC. FIXTURE TYPE: PROJECT NAME:
Bol 8' 24' Round Tapered and Straight Wood Poles FIXTURE TYPE: PROJECT NAME: Round Taper Glulam solid wood and aluminum pole available in 8' 24' lengths. Tenon adapters, slip fitters and side bracket mounts
More informationBUILDING DESIGN STANDARDS FACILITIES MANAGEMENT AND ANCILLARY SERVICES EXTERIOR IMPROVEMENTS DIVISION 32 Exterior Site Furnishings
PART 1 GENERAL 1.1 Summary.1 Unless otherwise indicated, follow the standards below when specifying exterior site furnishings. These standards are not intended to restrict or replace professional judgment.
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 099123 - INTERIOR PAINTING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationWAL-MART SUPERCENTER # ; Milwaukie, OR: SPECIFICATIONS. Revisions to Specification Fence
MILWAUKIE OR #3144-00 ADDENDUM #5 NARRATIVE: 11-08-12 WAL-MART SUPERCENTER #3144-00; Milwaukie, OR: SPECIFICATIONS SPECIFICATIONS Revisions to Specification 02822 Fence Spec division 02822 has been revised
More informationEngineering Services Program
GDR41 1214 Product Evaluation Engineering Services Program The following product has been evaluated for compliance with the wind loads specified in the International Residential Code (IRC) and the International
More informationPREFOAM - PERMANENT STADIUM SEATING RISER SYSTEM FOR FLOOR MONTED SEATING PART 1 GENERAL DESCRIPTION
PREFOAM - PERMANENT STADIUM SEATING RISER SYSTEM FOR FLOOR MONTED SEATING PART 1 GENERAL DESCRIPTION 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary
More informationSECTION SHEET METAL FLASHING AND TRIM
SECTION 07620 PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Formed roof drainage sheet metal fabrications. 2. Formed low-slope roof sheet metal fabrications. 1.2 SUBMITTALS A. Shop Drawings: Show
More informationPROJECT LOCATION SECTION PREFINISHED STEEL DOOR FRAMES
SECTION 08 1213.17 PART 1 - GENERAL 1.01 SECTION INCLUDES A. Prefinished steel door frames. B. [Sidelites] [, borrowed lites] [, and transom] assemblies. 1.02 RELATED REQUIREMENTS A. Section 06 2000 Finish
More informationINSTALLATION MANUAL STORAGE
IMVersion 1.1 INSTALLATION MANUAL GENERAL GUIDE: The information in this IM is intended to serve as a general guide to proper installation with no warranties intended or implied. Prime Panels assumes no
More informationSeptember 10, 2009 Page 1 PRODUCT DESCRIPTION PRODUCT FEATURES
September 10, 2009 Page 1 PRODUCT FEATURES BASIC USES/RELATED USES Interior decorative tile. Architectural tile for decorative wall surfaces, backsplashes and other applications. Custom architectural and
More information1.1 RELATED DOCUMENTS
SECTION 050505 -BEVEL RAIL ENDS PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the contract, including General and Supplementary Conditions and Division 01 Specification Sections
More informationB. See Division 05 Section "Pipe and Tube Railings" for metal pipe and tube railings.
SECTION 055000 - METAL FABRICATIONS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following, applicable: 1. Miscellaneous steel framing and supports. 2. Prefabricated building columns. 3. Shelf
More informationProduct Guide Specification
Product Guide Specification Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat,
More informationDowntown Rack. Custom logo option available
Custom logo option available Downtown Rack The Downtown Rack uses thick, square-tube construction that can t be cut with a pipe cutter. The extended width of the Downtown Rack makes for easy bike parking
More informationSafe and secure Dero
B I K E D E P OT Safe and secure Whether the project is at a transit station, university campus, or residential building, the Bike Depot s modular design lets customers easily build out to meet their space
More informationWritten by Administrator Monday, 29 November :54 - Last Updated Thursday, 02 December :00
Security Screen Doors One of the most important decisions you will make in acquiring your door will the selection of the finish for your door. Two similar doors will seem very different depending on the
More informationSECTION Display Case Door Series 1301-CM
1 SECTION 12 3559 Display Case Door Series 1301-CM PART 1 - GENERAL 1.01 SUMMARY A. This section includes: 1. Display Case Glass Doors. 2. Sidelites. B. Related work in other sections: 1. 08 8000- Glazing
More informationSymphony II Adaptable Table System
Symphony II Adaptable Table System 1.00 General 1.01 Conditions 1.02 Scope of work 1. This section covers all materials, equipment, tools and labor for the supply and installation of the laboratory Symphony
More informationNew Product Release: October 2014 Boone Racks
New Product Release: October 2014 Boone Racks Double Fido Fountain Mounting: Surface NOTE: THESE ROUGH-IN DIMENSIONS MAY VARY ½: (13 mm) PLUS OR MINUS NOTE: All dimensions subject to manufacturing variance
More informationOxford Stalls Installation Instructions
Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or
More informationSECTION CHAIN LINK FENCING AND GATES
PART 1 GENERAL 1.01 SCOPE OF WORK A. The Contractor shall furnish and install all materials, labor, equipment and incidentals required to provide chain link fencing and gates as Shown on the Contract Drawings
More informationBrackets and Tenons. Product Specifications. PB Series XA-TMDA8
Product Specifications FINISH Exclusive Colorfast DeltaGuard finish features an E-Coat epoxy primer with an ultra-durable powder topcoat, providing excellent resistance to corrosion, ultraviolet degradation
More informationSTRUCTURAL STEEL AND ALUMINUM PART 1 - GENERAL 1.01 SCOPE:
SECTION 05100 STRUCTURAL STEEL AND ALUMINUM PART 1 - GENERAL 1.01 SCOPE: A. The WORK of this SECTION shall consist of furnishing all the labor, materials, and equipment necessary for installation of structural
More informationSpiral Slide
IMPORTANT Page 1 PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be installed in accordance with these instructions. Check your shipment against Bill of Lading and Parts list.
More informationSUNBELT transformer WIDTFA3501 PAINTING TRANSFORMERS WITH WATERBORNE PAINT SYSTEMS INTERNAL USE ONLY DOCUMENT HISTORY
SUNBELT transformer WIDTFA3501 PAINTING TRANSFORMERS WITH WATERBORNE PAINT SYSTEMS INTERNAL USE ONLY DOCUMENT HISTORY REV. DATE DESCRIPTION OF CHANGE AND REASON FOR CHANGE A JUNE 10, 1999 NEW ISSUE B JULY
More informationMH Series Mitered Frames shall be as manufactured or furnished by Republic Doors and Frames, McKenzie, Tennessee
drywall frames - mh series/mitered SHEET NO. 202 MH Series Mitered Frames shall be as manufactured or furnished by Republic Doors and Frames, McKenzie, Tennessee 38201. Profile - Made for two basic door
More informationNON-PENETRATING ROOFTOP HANGERS AND SUPPORTS
SECTION 15062 NON-PENETRATING ROOFTOP HANGERS AND SUPPORTS For best results, display hidden notes to specifier. PART 1 GENERAL 1.1 SECTION INCLUDES A. Pipe supports. B. Conduit supports. C. Duct supports,
More informationMITCHELL FURNITURE SYSTEMS, INC.
MITCHELL FURNITURE SYSTEMS, INC. MITCHELL WALL MOUNTED TABLE/BENCH SYSTEM: ARCHITECTURAL DATA Laminate, Backer & Adhesive GREENGUARD Certified Components PART I. - ATTENTION: SPECIFIER AND/OR ARCHITECT
More informationBrackets and Tenons. Product Specifications. PB Series
Brackets and Tenons Product Specifications FINISH Exclusive Colorfast DeltaGuard finish features an E-Coat epoxy primer with an ultra-durable powder topcoat, providing excellent resistance to corrosion,
More informationWALCOOM. Walcoom Corporation GARRISON FENCE.
WALCOOM Walcoom Corporation "Galvanized steel picket fence with absolute advantage over the wrought iron & stainless steel fence." Walcoom is a professional metal fencing manufacturer. We always adhere
More informationSuggested Specification for Preparing Hot-Dip Galvanized Steel Surfaces for Painting Revised February 2002
Suggested Specification for Preparing Hot-Dip Galvanized Steel Surfaces for Painting Revised February 2002 This suggested specification is provided as a guide to preparing a quality document calling for
More informationSHELDON Versatile seating
UK street furniture designers & manufacturers As UK based, designers and manufacturers, Street Design can manufacture and supply Sheldon seating to suit your specific requirements. Sheldon versatile seating
More informationFactory Assistance: Phone: Fax: Page 1
CABLE RUNWAY ACCESSORIES Radius Drop / Stringer Drop Provides 3 bend radius Radius drop fits 6, 12 and 18 runway made from 1-1/2 x 3/8 tubing Steel construction Includes (3) cable spools, (1) bolt, (1)
More informationETCHED PLAQUES by Matthews International
ETCHED PLAQUES by Matthews International Note: These specifications were current at the time of publication but are subject to change without notice. Please confirm the accuracy of these specifications
More informationBarofor Round System (polyester coated) Panels, Posts, Accessories
1 Scope This Technical Data Sheet specifies the requirements for the Barofor Round System. The complete system exists of: Panels Posts Accessories such as fixation system and posts caps. Panels and posts
More information