Portsmouth, NH. Wayfinding and Signage System City of Portsmouth, NH Planning Department 100% DESIGN INTENT DRAWINGS.

Transcription

1 Portsmouth, NH City of Portsmouth, NH Planning Department 00% DESIGN INTENT DRAWINGS January, 04 Rev: March 4, 04 0 North Church Street Suite 08 West Chester, PA 980 T

2 Section SIGN SYSTEM STANDARDS A. Graphic Standards Typography Specifications... A. Project Artwork... A.5 Color Chart... A.6 B. Placement Guidelines Standard Sign Placements... B. Section SIGNAGE DRAWINGS C. Menu of Sign Types Gateway Signage Overview (PLACEHOLDER)... C. Vehicular Signage Overview... C. Parking Signage Overview... C. Pedestrian Signage Overview... C.5 Regulatory Signage Overview... C.6 D. Design Intent Drawings Table of Contents VDIR... D. VDIR.L... D. VDIR... D. VDIR.L... D.4 VDIR... D.5 VDIR.L... D.6 VDIR.4... D.7 VDIR.5... D.8 VDIR.6... D.9 PARK... D.0 PARK... D. PARK.L... D. PARK... D. PARK D.4 PARK.4... D.7 PARK.5... D.8 PARK.6... D.9 PARK.7... D.0 PARK.8... D. PED... D. PED... D. KIOSK... D.4 PLAQUE... D.5 KIOSK... D.6 REG... D.7 REG... D.8 E. Graphic Layouts F. Construction Details Section Performance Specifications Section 4 Programming

3 SECTION Sign System Standards

4 A Graphic Standards

5 Clearview Highway ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdefghijklmnopqrstuvwxyz SPECIFICATIONS All type shall be set exactly as specified. Substitutions will only be accepted, at the DESIGNER S discretion, where they match the specified typeface in every detail. The FABRICATOR should be aware that different versions of typesetting equipment may not satisfactorily match specified typefaces and in such instances will not be acceptable. Amongst the several mechanical Arts that have engaged my attention, there is no one which I have pursued with so much steadiness and pleasure, as that of Letter Founding. Downtown Downtown Downtown acceptable NOT acceptable NOT acceptable A A A acceptable NOT acceptable NOT acceptable Sometimes the Foot mark is mistaken for an apostrophe and an inch mark is mistaken for quotations. Below are examples of correct and incorrect apostrophe s for each typeface. NOTES Clearview Highway ' This apostrophe is CORRECT. PARK S This apostrophe is INCORRECT. PARK'S This typeface is the primary typeface for most of the vehicular signage. SUBCONSULTANT 0 North Church Street Suite 08 West Chester, PA 980 T /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Typography Specifications A.

6 Bookman Old Style Bold ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdefghijklmnopqrstuvwxyz Amongst the several mechanical Arts that have engaged my attention, there is no one which I have pursued with so much steadiness and pleasure, as that of Letter Founding. SPECIFICATIONS All type shall be set exactly as specified. Substitutions will only be accepted, at the DESIGNER S discretion, where they match the specified typeface in every detail. The FABRICATOR should be aware that different versions of typesetting equipment may not satisfactorily match specified typefaces and in such instances will not be acceptable. Sometimes the Foot mark is mistaken for an apostrophe and an inch mark is mistaken for quotations. Below are examples of correct and incorrect apostrophe s for each typeface. Sometimes the Foot mark is mistaken for an apostrophe and an inch mark is mistaken for quotations. Below are examples of correct and incorrect apostrophe s for each typeface. Downtown Downtown Downtown acceptable NOT acceptable NOT acceptable A A A acceptable NOT acceptable NOT acceptable Bookman Old Style Bold ' FUTURA BOOK This apostrophe is CORRECT. PARK S This apostrophe is INCORRECT. PARK'S Mrs Eaves Small Caps ' This apostrophe is CORRECT. PARK S This apostrophe is INCORRECT. PARK'S FUTURA CONDENSED MEDIUM MRS EAVES SMALL CAPS ABCDEFGHIJKLMNOPQRSTUVWXYZ ABCDEFGHIJKLMNOPQRSTUVWXYZ !@#$%^ ' NOTES This apostrophe is CORRECT. PARK S This apostrophe is INCORRECT. PARK'S ' These typefaces are primary typefaces and are used within the identity system. This apostrophe is CORRECT. PARK S This apostrophe is INCORRECT. PARK'S AMONGST THE SEVERAL MECHANICAL ARTS THAT HAVE ENGAGED MY ATTENTION, THERE IS NO ONE WHICH I HAVE PURSUED WITH SO MUCH STEADINESS AND PLEASURE, AS THAT OF LETTER FOUNDING. 0 North Church Street Suite 08 West Chester, PA 980 T DOWNTOWN DOWNTOWN D OWNTOWN acceptable NOT acceptable NOT acceptable A A A acceptable NOT acceptable NOT acceptable SUBCONSULTANT /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Typography Specifications A.

7 SPECIFICATIONS Myriad Pro Condensed ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdefghijklmnopqrstuvwxyz Amongst the several mechanical Arts that have engaged my attention, there is no one which I have pursued with so much steadiness and pleasure, as that of Letter Founding. All type shall be set exactly as specified. Substitutions will only be accepted, at the DESIGNER S discretion, where they match the specified typeface in every detail. The FABRICATOR should be aware that different versions of typesetting equipment may not satisfactorily match specified typefaces and in such instances will not be acceptable. Downtown Downtown Downtown acceptable NOT acceptable NOT acceptable A A A acceptable NOT acceptable NOT acceptable Myriad Pro Bold Condensed ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdefghijklmnopqrstuvwxyz !@#$%^ Amongst the several mechanical Arts that have engaged my attention, there is no one which I have pursued with so much steadiness and pleasure, as that of Letter Founding. Downtown Downtown Downtown acceptable NOT acceptable NOT acceptable A A A acceptable NOT acceptable NOT acceptable NOTES This typeface is a secondary typeface and is used within the identity system. SUBCONSULTANT Sometimes the Foot mark is mistaken for an apostrophe and an inch mark is mistaken for quotations. Below are examples of correct and incorrect apostrophe s for each typeface. ' Myriad Pro Condensed This apostrophe is CORRECT. PARK S This apostrophe is INCORRECT. PARK'S /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. 0 North Church Street Suite 08 West Chester, PA 980 T Sometimes the Foot mark is mistaken for an apostrophe and an inch mark is mistaken for quotations. Below are examples of correct and incorrect apostrophe s for each typeface. ' Myriad Pro Bold Condensed This apostrophe is CORRECT. PARK S This apostrophe is INCORRECT. PARK'S Typography Specifications A.

8 LETTER-SPACING Inconsistencies in Letter Spacing Corrected Letter Spacing SPECIFICATIONS Individual spacing of each letter needs to be evaluated. All copy shall be kerned so that each character is optically centered between the center of each of the surrounding characters. TYPEFACE TYPEFACE Portsmouth Portsmouth TYPEFACE TYPEFACE Portsmouth Portsmouth TYPEFACE TYPEFACE Portsmouth Portsmouth IMPORTANT: Individual spacing of each letter needs to be evaluated. See Examples Above. Kern all Copy so that each character is optically centered between the center of each of the surrounding characters. SIGN TEXT STANDARDS COPY HEIGHT LINE SPACING NOTES When measuring copy height, measure only the height of the Capital letters to determine your overall copy height (shown in illustration below as X ) Some of the other letters have an extended height beyond the average height of the letters. X EjklH baseline X When measuring line spacing, always measure from the baseline of the topmost text line to the baseline of the text line below (shown as X ) EjklH EjklH baseline baseline SUBCONSULTANT /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. 0 North Church Street Suite 08 West Chester, PA 980 T Typography Specifications A.4

9 SPECIFICATIONS GRAPHIC ELEMENTS All artwork pictured on this page will be provided to the sign fabricator by the designer and/or client. This artwork must be used for all sign applications in this provided documentation. Do NOT substitute with any other artwork! PORTSMOUTH MARKET SQUARE WATERFRONT SYMBOLS USE of Arrows When multiple directions are required on a sign, the following directional hierarchy shall take precedent. See Example below. Reference Message Schedule for individual Messages. Straight Arrow ARROWS Left Arrow Right Arrow NOTES Left Arrow Up-Left Arrow Straight Arrow Up-Right Arrow Right Arrow SUBCONSULTANT 0 North Church Street Suite 08 West Chester, PA 980 T Straight-Left Arrow Up-Straight-Left Arrow Up-Straight-Right Arrow Straight-Right Arrow /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Project Artwork A.5

10 SPECIFICATIONS R REFLECTIVE VINYL NAME SPECIFICATION APPLICABLE PROCESS R R White Navy M High Intensity Prismatic Reflective Sheeting 90 Color: White M High Intensity Prismatic Reflective Sheeting 90 Color Match: PMS 7545 Standard for System (typ.) Standard for System (typ.) Knockout White: Background and Characters M custom inks direct to 90 with M approved Clear UV/Graffiti overlaminate. *Applied according to Manufacturers Spec to aluminum sheet. Custom Color: Background and Characters M custom inks direct to 90 with M approved Clear UV/Graffiti overlaminate. *Applied according to Manufacturers Spec to aluminum sheet. The FABRICATOR must submit three () identical sets of each color specified for approval prior to any painting. Sample paint swatches must be produced on.080" aluminum sheet, approximately " x 6", including primer and free of defects. Sample material swatches should be the same approximate size. Samples MUST have project and color specifications attached to back side. R R4 Green Teal M High Intensity Prismatic Reflective Sheeting 90 Color Match: PMS 565 M High Intensity Prismatic Reflective Sheeting 90 Color Match: PMS 550 Standard for System (typ.) Standard for System (typ.) Custom Color: Background and Characters M custom inks direct to 90 with M approved Clear UV/Graffiti overlaminate. *Applied according to Manufacturers Spec to aluminum sheet. Custom Color: Background and Characters M custom inks direct to 90 with M approved Clear UV/Graffiti overlaminate. *Applied according to Manufacturers Spec to aluminum sheet. The colors must look exactly the same every time they are used so that people associate them with the Portsmouth New Hampshire Wayfinding Program. All media, vinyl, paint, and inks must be produced so that the colors match as specified on this page. R5 Orange M High Intensity Prismatic Reflective Sheeting 90 Color Match: 0 Standard for System (typ.) Custom Color: Background and Characters M custom inks direct to 90 with M approved Clear UV/Graffiti overlaminate. *Applied according to Manufacturers Spec to aluminum sheet. R6 Royal Blue M High Intensity Prismatic Reflective Sheeting 90 Color Match: 78 Standard for System (typ.) Custom Color: Background and Characters M custom inks direct to 90 with M approved Clear UV/Graffiti overlaminate. *Applied according to Manufacturers Spec to aluminum sheet. * MUST comply with MUTCD section Table A- Minimum maintained retroreflectivity levels. Approved process: Durst RHO 6 TS printer. Sherine Industries: (604) NOTE: All M products are to be processed and applied according to M specifications. The seaming of material is NOT preferred. If the height of a sign panel is greater then 48 inches, the M 90 material should be oriented vertically with stripes at 0 degrees, to avoid the seaming of material. If seaming is required, it should occur at the rule line or between messages. V VINYL NAME SPECIFICATION APPLICABLE PROCESS V White M Schotchcal Opaque Vinyl Color: 80C-0 White Standard for System (typ.) Surface applied. V Orange M Schotchcal Opaque Vinyl Color: PMS 0 Standard for System (typ.) Surface applied. V Teal M Schotchcal Opaque Vinyl Color: PMS 550 Standard for System (typ.) Surface applied. V4 Royal Blue M Schotchcal Opaque Vinyl Color: 78 Standard for System (typ.) Surface applied. P PAINTS NAME SPECIFICATION APPLICABLE PROCESS P Navy To match PMS 7545 Standard for System (typ.) Surface applied, exterior sign paint and protective top coat: MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish. P Green To match PMS 565 Standard for System (typ.) Surface applied, exterior sign paint and protective top coat: MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish. P Citron To match PMS 604 Standard for System (typ.) Surface applied, exterior sign paint and protective top coat: MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish. NOTES P4 Teal To match PMS 550 Standard for System (typ.) Surface applied, exterior sign paint and protective top coat: MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish. P5 Brown To match PMS 4 Standard for System (typ.) Surface applied, exterior sign paint and protective top coat: MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish. P6 Black Hole Metallic To match MP995 Standard for System (typ.) Surface applied, exterior sign paint and protective top coat: MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish. P7 P8 P9 Black is Back Light Teal White To match MP59647 To match PMS 64 To match PMS White P0 Orange To match PMS 0 P Royal Blue To match PMS 78 P Light Silver Metallic To match MP807 P Yellow To match PMS 9 Standard for System (typ.) Standard for System (typ.) Standard for System (typ.) Standard for System (typ.) Standard for System (typ.) Standard for System (typ.) Standard for System (typ.) Surface applied, exterior sign paint and protective top coat: MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish. Surface applied, exterior sign paint and protective top coat: MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish. Surface applied, exterior sign paint and protective top coat: MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish. Surface applied, exterior sign paint and protective top coat: MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish. Surface applied, exterior sign paint and protective top coat: MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish. Surface applied, exterior sign paint and protective top coat: MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish. Surface applied, exterior sign paint and protective top coat: MATTHEWS Acrylic Polyurethane with Clear Coat Satin finish. SUBCONSULTANT /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. 0 North Church Street Suite 08 West Chester, PA 980 T Vinyl & Paint Color Chart A.6

11 B Placement Guidelines

12 SPECIFICATIONS SIGN TYPE a MEASURE PREFFERED DISTANCE MINIMUM DISTANCE Distance from Edge of Sign Panel to Edge of Curb '-0" or more ' - 0" Lateral Clearance Guidelines Within some of the Downtown areas of Portsmouth New Hampshire urban conditions and narrow sidewalks may cause deviation from the standards articulated in the previous figures. Conditions may include less lateral clearance for the '-0" or 5'-0" preferred distance from edge of sign panel to curb, or placement at '-0" or 5'-0" would create an obstacle (i.e. post positioned in middle of the side walk) or create situations of non-compliance to ADA clearances. b Distance from Sign Post to Nearest Obstruction 4' - 0" or more ' - 0" In these cases guidelines must be consistent with MUTCD Section A.9 options for urban areas. Suggested recommendations for relocation of signs if placement is in conflict with guidelines. c d Distance from Edge of Sign Panel to 4' - 0" or more ' - 0" Nearest Overhead Obstruction Sign Placement in Relation to Adjacent Building align to building Edge Do Not obstruct Entrance OPTION A: Position the sign at a minimum of '-0" or 5'-0" (face of curb to edge of sign panel) as required. OPTION B: If the sign can be moved, without disrupting routing or sequencing, then it should be repositioned to achieve the '-0" or 5'-0" min. If '-0" is not physically possible, then the following options should be allowed: OPTION C: The sign set back should be position at '-6". If that is not possible then... e Distance from Face of Sign to Nearest Tree Branch 0' - 0" or more 5' - 0" OPTION D: Utilize a minimum '- 0", in accordance with MUTCD, only as a final option. f Distance from Face of Sign to Nearest Utlity Pole 5' - 0" or more 0' - 0" g Distance from Back of Sign to Nearest Tree Branch 8' - 0" or more ' - 0" g h b c h Distance from Back of Sign to Nearest Utility Pole 5' - 0" or more 0' - 0" Measurements and Distances shown are guidelines only prevailing local and state codes shall supersede information presented. NOTES a e f 0 North Church Street Suite 08 West Chester, PA 980 T SUBCONSULTANT d /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Placement Guidelines B.

13 SPECIFICATIONS Lateral Clearance Guidelines Gutter Curb Example of Sidewalk & City Right of Way (Sidewalk widths vary) Within some of the Downtown areas of Portsmouth New Hampshire, urban conditions and narrow sidewalks may cause deviation from the standards articulated in the previous figures. Conditions may include less lateral clearance for the '-0" or 5'-0" preferred distance from edge of sign panel to curb, or placement at '-0" or 5'-0" would create an obstacle (i.e. post positioned in middle of the side walk) or create situations of non-compliance to ADA clearances. In these cases guidelines must be consistent with MUTCD Section A.9 options for urban areas. Suggested recommendations for relocation of signs if placement is in conflict with guidelines. OPTION A: Position the sign at a minimum of '-0" or 5'-0" (face of curb to edge of sign panel) as required. OPTION B: If the sign can be moved, without disrupting routing or sequencing, then it should be repositioned to achieve the '-0" or 5'-0" min. If '-0" is not physically possible, then the following options should be allowed: ADA required '-0" minimum Sidewalk Element: Canopy, Bench, Tree-grate Stairs, Building Entrance, etc. OPTION C: The sign set back should be position at '-6". If that is not possible then... OPTION D: Utilize a minimum '- 0", in accordance with MUTCD, only as a final option. -0 typ. to Curb ( -0 Min.) Sign Panel Pole/Breakaway 5 Foot Furnishing Zone NOTE: All locations shall be installed within the City ROW. If during the initial survey it is determined any part of the sign (pole or panel) extends outside of the City s Right of Way vertical plane and into private property, the installer must notify the city prior to fabrication/installation. NOTES Reference View: Example - 5 foot Furnishing Zone / City Right of Way SCALE: Not To Scale Note: Top View of VDIR.- shown as example. 0 North Church Street Suite 08 West Chester, PA 980 T SUBCONSULTANT /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Placement Guidelines B.

14 SECTION Signage Drawings

15 C Menu of Sign Types

16 SPECIFICATIONS PLACEHOLDER PAGE FUTURE GATEWAY SIGNS. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Gateway Signage Overview C.

17 SPECIFICATIONS Strawbery Banke Hanover Garage Discover Portsmouth West End District Strawbery Banke Hanover Garage VDIR.L VDIR.L VDIR.L Strawbery Banke Hanover Garage Discover Portsmouth West End District Strawbery Banke Hanover Garage Downtown Beaches Pease Intl. Tradeport Albacore Park Destination Message Destination Destination. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T /8/0 VDIR. Vehicular Directional (4 Message - 5 MPH or Less) VDIR. Vehicular Directional (4 Message - 5MPH or Less) VDIR. Vehicular Directional (4 Message - 5MPH or Less) VDIR.4 Vehicular Directional (6 Message - 0MPH or More) VDIR.5 Vehicular Directional (6 Message - 0MPH or More) VDIR.6 Vehicular Directional (6 Message - 0MPH or More) These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Vehicular Signage Overview C.

18 SPECIFICATIONS GARAGE PARKING PARK. Parking Lot Trailblazer (SS Strap -mounted) Bridge St. Lot PARK. Parking Lot Directional (Post-mounted) Bridge St. Lot PARK.L Parking Lot Directional (Post-mounted) PORTSMOUTH Bridge St. Parking Lot PUBLIC PARKING No Overnight Parking Vehicles Will Be Towed PARK. Parking Lot Identification (Post-mounted) PARK.4 Parking Garage Identification (Overhead) PARK.5 Parking Garage Directional (Overhead) PORTSMOUTH PARKING BRIDGE ST LOT PARK.8 LED Parking Sign (Post-mounted). Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. /8/0 0 North Church Street Suite 08 West Chester, PA 980 T Parking Signage Overview C.

19 SPECIFICATIONS HANOVER GARAGE PUBLIC PARKING Entrance Clearance 7' " Exit Only. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T /8/0 PARK.7 Parking Garage Identification (Mounted Letters) PARK.8 Parking Garage Directional (Overhead) These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Drawing Description C.4

20 SPECIFICATIONS KIOSK.a Kiosk Panel Sign Hanover Garage Market Square Music Hall Post Office Prescott Park KIOSK.b Kiosk Sign Seacoast Theatre Strawbery Banke Visitor Center. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. W elds: All welds shall be ground smooth, paint all seams.. H ardware: All exposed hardware shall be tamper proof fasteners. E N V I R O N M E N T S WAT E R F RON T 5M IN UTE WA L K KIOSK.c Kiosk Map Hanover Garage Market Square Music Hall Post Office E X P E R I E N C E S 0 North Church Street Suite 08 West Chester, PA 980 T MARKET SQUARE MAP ARTWORK TBD & Prescott Park Seacoast Theatre Strawberry Banke Visitor Center Hanover Garage Market Square Music Hall Post Office Prescott Park Seacoast Theatre Strawberry Banke Visitor Center. mi. mi. mi.4 mi.5 mi.5 mi.7 mi.5 mi /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. PED. Pedestrian Directional PED. Pedestrian Map + Directional KIOSK. Pedestrian Map + Information PLAQUE. Sidewalk Plaque KIOSK.a-c Pedestrian Kiosk (Reface Existing) Pedestrian Signage Overview C.5 Pedestrian Signage CITY OF January 04 Schematic Design

21 SPECIFICATIONS 95. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T /8/0 REG. Regulatory Sign (Post -mounted) Back View REG. Regulatory Sign (Post-mounted) Back View These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Regulatory Signage Overview C.6

22 KEY: S V8 9 D Design Intent Drawings Color Designator Specification Note The Color Designator Chart is found in the Graphic Standards section. The Specification Notation is found on the same page as the drawings.

23 SPECIFICATIONS SIGN TYPE: VDIR. FUNCTION: Vehicular Directional '- /" 4 Top View: VDIR. SCALE: /" = '-0" '-0" Strawbery Banke P7 F. F. R 7 4" F. F. R 7 P7 F. ARTWORK TBD F.4 F.4 9 P6 8 F. P5 4 4 F. P P P8 P " SQUARE POST MATERIAL: Aluminum Square Tube " x 4.50" x.50" wall FABRICATION PROCESS: Extruded CORNERS: Square, Smooth COLOR: Custom, as noted FOOTER: As per NHDOT breakaway specs. 4. CUSTOM FINIAL - ALL POSTS MATERIAL: Cast Aluminum CORNERS: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 6. SIGN PANEL BRACKET MATERIAL: Aluminum Angle -.50" wall FABRICATION PROCESS: Extruded, Saw Cut EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 7. /4" SIGN PANEL FRONT - REFLECTIVE MATERIAL: /4" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to 90 with M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications) FASTENER: Press-roll per M requirements. 8. SIGN PANEL BACKS - PAINT 9. ART PATTERN BACK PANEL COLOR: custom GRAPHICS APPLICATION: Applied Vinyl SURFACE PROCESS: GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to Vinyl with M approved UV/Graffiti Vinyl Over-laminate.. DECORATIVE TOP BRACKET MATERIAL: Aluminum sheet - " wide x.60" wall (6 gauge) FABRICATION PROCESS: Router Cut, Rolled, Brake-formed EDGES: Square, Smooth FASTENER: Weld rolled bracket to flat stock. Tamper-resistant mechanically fastened to post and Panel Bracket. 5. BREAKAWAY FOOTER FOOTER: The Transpo break-away system, according to specifications per NHDOT. P5 NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. '-0" min '-0" recommended 7'-6" 7'- 7/8" 0 North Church Street Suite 08 West Chester, PA 980 T SUBCONSULTANT Front View: VDIR. SCALE: /" = '-0" 5 Back View: VDIR. SCALE: /" = '-0" Side View: VDIR. SCALE: /" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type VDIR. Vehicular Directional D.

24 SPECIFICATIONS SIGN TYPE: VDIR.L FUNCTION: Vehicular Directional 4 Top View: VDIR. LSCALE: /" = '-0" Strawbery Banke P7 F. F. R 7 4" F. F. '- /" '-0" R 7 P7 ARTWORK TBD F.4 F. F.4 9 P6 8 F. P5 4 4 F. P P P8 P " SQUARE POST MATERIAL: Aluminum Square Tube " x 4.50" x.50" wall FABRICATION PROCESS: Extruded CORNERS: Square, Smooth COLOR: Custom, as noted FOOTER: As per NHDOT breakaway specs. 4. CUSTOM FINIAL - ALL POSTS MATERIAL: Cast Aluminum CORNERS: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 6. SIGN PANEL BRACKET MATERIAL: Aluminum Angle -.50" wall FABRICATION PROCESS: Extruded, Saw Cut EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 7. /4" SIGN PANEL FRONT - REFLECTIVE MATERIAL: /4" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to 90 with M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications) FASTENER: Press-roll per M requirements. 8. SIGN PANEL BACKS - PAINT 9. ART PATTERN BACK PANEL COLOR: custom GRAPHICS APPLICATION: Applied Vinyl SURFACE PROCESS: GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to Vinyl with M approved UV/Graffiti Vinyl Over-laminate.. DECORATIVE TOP BRACKET MATERIAL: Aluminum sheet - " wide x.60" wall (6 gauge) FABRICATION PROCESS: Router Cut, Rolled, Brake-formed EDGES: Square, Smooth FASTENER: Weld rolled bracket to flat stock. Tamper-resistant mechanically fastened to post and Panel Bracket. 5. BREAKAWAY FOOTER FOOTER: The Transpo break-away system, according to specifications per NHDOT. P5 NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. '-0" min '-0" recommended 7'-6" 7'- 7/8" 0 North Church Street Suite 08 West Chester, PA 980 T SUBCONSULTANT Front View: VDIR.L SCALE: /" = '-0" 5 Back View: VDIR.L SCALE: /" = '-0" Side View: VDIR.L SCALE: /" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type VDIR.L Vehicular Directional D.

25 SPECIFICATIONS SIGN TYPE: VDIR. FUNCTION: Vehicular Directional F. F. F. 4'-5 /" 4 4" Top View: VDIR. SCALE: /" = '-0" '-0" Hanover Garage Discover Portsmouth P7 R 7 R 7 R4 7 R6 7 R 7 R5 7 R6 7 P7 F. F. ARTWORK TBD F.4 F.4 9 P6 8 F. P5 4 4 F. P P P8 P " SQUARE POST MATERIAL: Aluminum Square Tube " x 4.50" x.50" wall FABRICATION PROCESS: Extruded CORNERS: Square, Smooth COLOR: Custom, as noted FOOTER: As per NHDOT breakaway specs. 4. CUSTOM FINIAL - ALL POSTS MATERIAL: Cast Aluminum CORNERS: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 6. SIGN PANEL BRACKET MATERIAL: Aluminum Angle -.50" wall FABRICATION PROCESS: Extruded, Saw Cut EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 7. /4" SIGN PANEL FRONT - REFLECTIVE MATERIAL: /4" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to 90 with M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications) FASTENER: Press-roll per M requirements. 8. SIGN PANEL BACKS - PAINT 9. ART PATTERN BACK PANEL COLOR: custom GRAPHICS APPLICATION: Applied Vinyl SURFACE PROCESS: GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to Vinyl with M approved UV/Graffiti Vinyl Over-laminate.. DECORATIVE TOP BRACKET MATERIAL: Aluminum sheet - " wide x.60" wall (6 gauge) FABRICATION PROCESS: Router Cut, Rolled, Brake-formed EDGES: Square, Smooth FASTENER: Weld rolled bracket to flat stock. Tamper-resistant mechanically fastened to post and Panel Bracket. 5. BREAKAWAY FOOTER FOOTER: The Transpo break-away system, according to specifications per NHDOT. P5 NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. '-0" min '-0" recommended 7'-6" SUBCONSULTANT 0 North Church Street Suite 08 West Chester, PA 980 T Front View: VDIR. SCALE: /" = '-0" 5 Back View: VDIR. SCALE: /" = '-0" Side View: VDIR. SCALE: /" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type VDIR. Vehicular Directional D.

26 SPECIFICATIONS SIGN TYPE: VDIR.L FUNCTION: Vehicular Directional F. F. F. 4'-5 /" 4 4" Top View: VDIR.L SCALE: /" = '-0" '-0" Hanover Garage Discover Portsmouth P7 R 7 R 7 R4 7 R6 7 R 7 R5 7 R6 7 P7 ARTWORK TBD F.4 F. F. F.4 P6 8 9 F. P5 4 4 F. P P P8 P " SQUARE POST MATERIAL: Aluminum Square Tube " x 4.50" x.50" wall FABRICATION PROCESS: Extruded CORNERS: Square, Smooth COLOR: Custom, as noted FOOTER: As per NHDOT breakaway specs. 4. CUSTOM FINIAL - ALL POSTS MATERIAL: Cast Aluminum CORNERS: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 6. SIGN PANEL BRACKET MATERIAL: Aluminum Angle -.50" wall FABRICATION PROCESS: Extruded, Saw Cut EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 7. /4" SIGN PANEL FRONT - REFLECTIVE MATERIAL: /4" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to 90 with M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications) FASTENER: Press-roll per M requirements. 8. SIGN PANEL BACKS - PAINT 9. ART PATTERN BACK PANEL COLOR: custom GRAPHICS APPLICATION: Applied Vinyl SURFACE PROCESS: GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to Vinyl with M approved UV/Graffiti Vinyl Over-laminate.. DECORATIVE TOP BRACKET MATERIAL: Aluminum sheet - " wide x.60" wall (6 gauge) FABRICATION PROCESS: Router Cut, Rolled, Brake-formed EDGES: Square, Smooth FASTENER: Weld rolled bracket to flat stock. Tamper-resistant mechanically fastened to post and Panel Bracket. 5. BREAKAWAY FOOTER FOOTER: The Transpo break-away system, according to specifications per NHDOT. P5 NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. '-0" min '-0" recommended 7'-6" 7'- 7/8" 0 North Church Street Suite 08 West Chester, PA 980 T SUBCONSULTANT Front View: VDIR.L SCALE: /" = '-0" 5 Back View: VDIR.L SCALE: /" = '-0" Side View: VDIR.L SCALE: /" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type VDIR.L Vehicular Directional D.4

27 SPECIFICATIONS SIGN TYPE: VDIR. FUNCTION: Vehicular Directional. 4.5" SQUARE POST MATERIAL: Aluminum Square Tube " x 4.50" x.50" wall FABRICATION PROCESS: Extruded CORNERS: Square, Smooth COLOR: Custom, as noted FOOTER: As per NHDOT breakaway specs. 9. ART PATTERN BACK PANEL COLOR: custom GRAPHICS APPLICATION: Applied Vinyl SURFACE PROCESS: GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to Vinyl with M approved UV/Graffiti Vinyl Over-laminate. F. F. F. 5'-7 /" 4 4" Top View: VDIR. SCALE: /" = '-0" '-0" West End District Strawbery Banke Hanover Garage P7 R 7 R 7 R 7 R4 7 R6 7 P7 F. F. ARTWORK TBD F.4 F.4 9 P6 8 F. P5 4 4 F. P P P8 P CUSTOM FINIAL - ALL POSTS MATERIAL: Cast Aluminum CORNERS: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 6. SIGN PANEL BRACKET MATERIAL: Aluminum Angle -.50" wall FABRICATION PROCESS: Extruded, Saw Cut EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 7. /4" SIGN PANEL FRONT - REFLECTIVE MATERIAL: /4" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to 90 with M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications) FASTENER: Press-roll per M requirements. 8. SIGN PANEL BACKS - PAINT. DECORATIVE TOP BRACKET MATERIAL: Aluminum sheet - " wide x.60" wall (6 gauge) FABRICATION PROCESS: Router Cut, Rolled, Brake-formed EDGES: Square, Smooth FASTENER: Weld rolled bracket to flat stock. Tamper-resistant mechanically fastened to post and Panel Bracket. 5. BREAKAWAY FOOTER FOOTER: The Transpo break-away system, according to specifications per NHDOT. P5 NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. '-0" min '-0" recommended 7'-6" SUBCONSULTANT 0 North Church Street Suite 08 West Chester, PA 980 T Front View: VDIR. SCALE: /" = '-0" 5 Back View: VDIR. SCALE: /" = '-0" Side View: VDIR. SCALE: /" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type VDIR. Vehicular Directional D.5

28 SPECIFICATIONS SIGN TYPE: VDIR.L FUNCTION: Vehicular Directional. 4.5" SQUARE POST MATERIAL: Aluminum Square Tube " x 4.50" x.50" wall FABRICATION PROCESS: Extruded CORNERS: Square, Smooth COLOR: Custom, as noted FOOTER: As per NHDOT breakaway specs. 9. ART PATTERN BACK PANEL COLOR: custom GRAPHICS APPLICATION: Applied Vinyl SURFACE PROCESS: GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to Vinyl with M approved UV/Graffiti Vinyl Over-laminate. F. F. F. 5'-7 /" 4 4" Top View: VDIR.L SCALE: /" = '-0" '-0" West End Strawbery Banke Hanover Garage P7 R 7 R 7 R 7 R4 7 R6 7 P7 ARTWORK TBD F.4 F. F. F.4 P6 8 9 F. P5 4 4 F. P P P8 P CUSTOM FINIAL - ALL POSTS MATERIAL: Cast Aluminum CORNERS: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 6. SIGN PANEL BRACKET MATERIAL: Aluminum Angle -.50" wall FABRICATION PROCESS: Extruded, Saw Cut EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 7. /4" SIGN PANEL FRONT - REFLECTIVE MATERIAL: /4" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to 90 with M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications) FASTENER: Press-roll per M requirements. 8. SIGN PANEL BACKS - PAINT. DECORATIVE TOP BRACKET MATERIAL: Aluminum sheet - " wide x.60" wall (6 gauge) FABRICATION PROCESS: Router Cut, Rolled, Brake-formed EDGES: Square, Smooth FASTENER: Weld rolled bracket to flat stock. Tamper-resistant mechanically fastened to post and Panel Bracket. 5. BREAKAWAY FOOTER FOOTER: The Transpo break-away system, according to specifications per NHDOT. P5 NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. '-0" min '-0" recommended 7'-6" 7'- 7/8" 0 North Church Street Suite 08 West Chester, PA 980 T SUBCONSULTANT Front View: VDIR.L SCALE: /" = '-0" 5 Back View: VDIR.L SCALE: /" = '-0" Side View: VDIR.L SCALE: /" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type VDIR.L Vehicular Directional D.6

29 SPECIFICATIONS SIGN TYPE: VDIR.4 FUNCTION: Vehicular Directional 4 Top View: VDIR.4 SCALE: /" = '-0" 7'-5". 6" SQUARE POST MATERIAL: Aluminum Square Tube 606-6" x 6" x.50" wall FABRICATION PROCESS: Extruded CORNERS: Square, Smooth COLOR: Custom, as noted FOOTER: As per NHDOT breakaway specs. 4. CUSTOM FINIAL - ALL POSTS MATERIAL: Cast Aluminum CORNERS: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 6. SIGN PANEL BRACKET MATERIAL: Aluminum Angle -.50" wall FABRICATION PROCESS: Extruded, Saw Cut EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 9. ART PATTERN BACK PANEL COLOR: custom GRAPHICS APPLICATION: Applied Vinyl SURFACE PROCESS: GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to Vinyl with M approved UV/Graffiti Vinyl Over-laminate.. DECORATIVE TOP BRACKET MATERIAL: Aluminum sheet - " wide x.60" wall (6 gauge) FABRICATION PROCESS: Router Cut, Rolled, Brake-formed EDGES: Square, Smooth FASTENER: Weld rolled bracket to flat stock. Tamper-resistant mechanically fastened to post and Panel Bracket. 5. BREAKAWAY FOOTER FOOTER: The Transpo break-away system, according to specifications per NHDOT. F. F. F. '- /" /" '- /" '- /" 6" Downtown Beaches P7 R 7 R 7 P7 ARTWORK TBD F.4 F.4 9 P6 8 P5 4 P P P8 P4 F.4 4 F /4" SIGN PANEL FRONT - REFLECTIVE MATERIAL: /4" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to 90 with M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications) FASTENER: Press-roll per M requirements. 8. SIGN PANEL BACKS - PAINT NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 7'-0" 0'-0" 0 North Church Street Suite 08 West Chester, PA 980 T '-0" min '-0" recommended Front View: VDIR.4 SCALE: /" = '-0" P5 5 Back View: VDIR.4 SCALE: /" = '-0" Side View: VDIR.4 SCALE: /" = '-0" SUBCONSULTANT /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type VDIR.4 Vehicular Directional D.7

30 SPECIFICATIONS SIGN TYPE: VDIR.5 FUNCTION: Vehicular Directional F. F. F. '-5" /" '-" '- /" 6" 4 Top View: VDIR.5 SCALE: /" = '-0" 7'-5" Pease Intl. Tradeport Albacore Park P7 R 7 R 7 P7 ARTWORK TBD F.4 F.4 9 P6 8 '- /4" P5 4 F.4 P P P8 P4 4 F " SQUARE POST MATERIAL: Aluminum Square Tube 606-6" x 6" x.50" wall FABRICATION PROCESS: Extruded CORNERS: Square, Smooth COLOR: Custom, as noted FOOTER: As per NHDOT breakaway specs. 4. CUSTOM FINIAL - ALL POSTS MATERIAL: Cast Aluminum CORNERS: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 6. SIGN PANEL BRACKET MATERIAL: Aluminum Angle -.50" wall FABRICATION PROCESS: Extruded, Saw Cut EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 7. /4" SIGN PANEL FRONT - REFLECTIVE MATERIAL: /4" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to 90 with M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications) FASTENER: Press-roll per M requirements. 8. SIGN PANEL BACKS - PAINT NOTES 9. ART PATTERN BACK PANEL COLOR: custom GRAPHICS APPLICATION: Applied Vinyl SURFACE PROCESS: GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to Vinyl with M approved UV/Graffiti Vinyl Over-laminate.. DECORATIVE TOP BRACKET MATERIAL: Aluminum sheet - " wide x.60" wall (6 gauge) FABRICATION PROCESS: Router Cut, Rolled, Brake-formed EDGES: Square, Smooth FASTENER: Weld rolled bracket to flat stock. Tamper-resistant mechanically fastened to post and Panel Bracket. 5. BREAKAWAY FOOTER FOOTER: The Transpo break-away system, according to specifications per NHDOT.. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 7'-0" '-0" min '-0" recommended Front View: VDIR.5 SCALE: /" = '-0" P5 5 Back View: VDIR.5 SCALE: /" = '-0" Side View: VDIR.5 SCALE: /" = '-0" SUBCONSULTANT /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. 0 North Church Street Suite 08 West Chester, PA 980 T Sign Type VDIR.5 Vehicular Directional D.8

31 SPECIFICATIONS SIGN TYPE: VDIR.6 FUNCTION: Vehicular Directional F. F. F. 5'-0" '-" '-6 /" '-6 /" 6" 4 Top View: VDIR.4 SCALE: /" = '-0" 7'-5" Destination Message Destination P7 Destination R 7 R 7 P7 ARTWORK TBD F.4 F.4 9 P6 8 P5 4 P P P8 P4 F.4 4 F " SQUARE POST MATERIAL: Aluminum Square Tube 606-6" x 6" x.50" wall FABRICATION PROCESS: Extruded CORNERS: Square, Smooth COLOR: Custom, as noted FOOTER: As per NHDOT breakaway specs. 4. CUSTOM FINIAL - ALL POSTS MATERIAL: Cast Aluminum CORNERS: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 6. SIGN PANEL BRACKET MATERIAL: Aluminum Angle -.50" wall FABRICATION PROCESS: Extruded, Saw Cut EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 7. /4" SIGN PANEL FRONT - REFLECTIVE MATERIAL: /4" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to 90 with M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications) FASTENER: Press-roll per M requirements. 8. SIGN PANEL BACKS - PAINT NOTES 9. ART PATTERN BACK PANEL COLOR: custom GRAPHICS APPLICATION: Applied Vinyl SURFACE PROCESS: GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to Vinyl with M approved UV/Graffiti Vinyl Over-laminate.. DECORATIVE TOP BRACKET MATERIAL: Aluminum sheet - " wide x.60" wall (6 gauge) FABRICATION PROCESS: Router Cut, Rolled, Brake-formed EDGES: Square, Smooth FASTENER: Weld rolled bracket to flat stock. Tamper-resistant mechanically fastened to post and Panel Bracket. 5. BREAKAWAY FOOTER FOOTER: The Transpo break-away system, according to specifications per NHDOT.. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 7'-0" 0 North Church Street Suite 08 West Chester, PA 980 T '-0" min '-0" recommended Front View: VDIR.6 SCALE: /" = '-0" P5 5 Back View: VDIR.6 SCALE: /" = '-0" Side View: VDIR.6 SCALE: /" = '-0" SUBCONSULTANT /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type VDIR.6 Vehicular Directional D.9

32 SPECIFICATIONS SIGN TYPE: PARK. FUNCTION: Parking Trailblazer /4" Existing Light Pole P7 4. /8" SIGN PANEL FRONT - REFLECTIVE MATERIAL: /8" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to 90 with M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications) FASTENER: Press-roll per M requirements. 6 " Top View: PARK. SCALE: "='-0". SLEEVE MATERIAL: Aluminum U-channel (.60" wall) FABRICATION PROCESS: Extruded EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to sign panel. 5 Graphic Layout: PARK. SCALE: /" = '-0" 4. POLE STRAP ATTACHMENT PRODUCT: Band-It Band, or approved equal. MATERIAL: Type 0 SS, SIZE: /4 inch FINISH: Finish is to match color of existing pole. Utility pole-stainless steel Historic black pole-black band (P900) Cobrahead-stainless steel FASTENER: Ultra-Lok Free End clamps NOTE: Sign Contractor to coordinate the removal or movement of interfering existing signs on poles, with the city. '-" R4 R6 R R " Ø '-0 /8" Ø 0 /8" Ø 9 /4" P6 6" '-0" min. '-0 recommended 6" NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication. '-0". Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. '-" 7 /4" 6 /4" 0 North Church Street Suite 08 West Chester, PA 980 T " SUBCONSULTANT Front View: PARK. SCALE: /" = '-0" Side View: PARK. SCALE: /" = '-0" Back View: PARK. SCALE: /" = '-0" 4 Graphic Layout: PARK. SCALE: /" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type PARK. Parking Lot Trailblazer D.0

33 SPECIFICATIONS SIGN TYPE: PARK. FUNCTION: Parking Directional 4 Top View: PARK. SCALE: /" = '-0" P7 F.6 F.5 R 7 4" R 7 F.5 F.5 '- /" '-0" Bridge St. Lot R4 7 R6 7 P7 P5 F.6 5 Top View: PARK.-DOUBLE SIDED SCALE: /" = '-0" P 8 F.6 4 F.6 P5 4 P P P8 P " SQUARE POST MATERIAL: Aluminum Square Tube " x 4.50" x.50" wall FABRICATION PROCESS: Extruded CORNERS: Square, Smooth COLOR: Custom, as noted FOOTER: As per NHDOT breakaway specs. 4. CUSTOM FINIAL - ALL POSTS MATERIAL: Cast Aluminum CORNERS: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 6. SIGN PANEL BRACKET MATERIAL: Aluminum Angle -.50" wall FABRICATION PROCESS: Extruded, Saw Cut EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 7. /4" SIGN PANEL FRONT - REFLECTIVE MATERIAL: /4" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to 90 with M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications) FASTENER: Press-roll per M requirements. 8. SIGN PANEL BACKS - PAINT 9. ART PATTERN BACK PANEL COLOR: custom GRAPHICS APPLICATION: Applied Vinyl SURFACE PROCESS: GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to Vinyl with M approved UV/Graffiti Vinyl Over-laminate.. DECORATIVE TOP BRACKET MATERIAL: Aluminum sheet - " wide x.60" wall (6 gauge) FABRICATION PROCESS: Router Cut, Rolled, Brake-formed EDGES: Square, Smooth FASTENER: Weld rolled bracket to flat stock. Tamper-resistant mechanically fastened to post and Panel Bracket. 5. BREAKAWAY FOOTER FOOTER: The Transpo break-away system, according to specifications per NHDOT. 7'-6" 7'- 5/8" NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. '-0"min '-0" recommended SUBCONSULTANT 0 North Church Street Suite 08 West Chester, PA 980 T Front View: PARK. SCALE: /" = '-0" 5 Back View: PARK. SCALE: /" = '-0" Side View: PARK. SCALE: /" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type PARK. Parking Lot Directional D.

34 SPECIFICATIONS SIGN TYPE: PARK.L FUNCTION: Parking Directional 4 Top View: PARK.L SCALE: /" = '-0" P7 F.6 F.5 R 7 4" R 7 F.5 F.5 '- /" '-0" Bridge St. Lot R4 7 R6 7 P7 P5 5 Top View: PARK.L-DOUBLE SIDED SCALE: /" = '-0" F.6 P 8 F.6 4 F.6 P5 4 P P P8 P " SQUARE POST MATERIAL: Aluminum Square Tube " x 4.50" x.50" wall FABRICATION PROCESS: Extruded CORNERS: Square, Smooth COLOR: Custom, as noted FOOTER: As per NHDOT breakaway specs. 4. CUSTOM FINIAL - ALL POSTS MATERIAL: Cast Aluminum CORNERS: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 6. SIGN PANEL BRACKET MATERIAL: Aluminum Angle -.50" wall FABRICATION PROCESS: Extruded, Saw Cut EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 7. /4" SIGN PANEL FRONT - REFLECTIVE MATERIAL: /4" thk Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Smooth GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to 90 with M approved UV/Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications) FASTENER: Press-roll per M requirements. 8. SIGN PANEL BACKS - PAINT 9. ART PATTERN BACK PANEL COLOR: custom GRAPHICS APPLICATION: Applied Vinyl SURFACE PROCESS: GRAPHIC BACKGROUND AND COPY PROCESS: M custom inks print direct to Vinyl with M approved UV/Graffiti Vinyl Over-laminate.. DECORATIVE TOP BRACKET MATERIAL: Aluminum sheet - " wide x.60" wall (6 gauge) FABRICATION PROCESS: Router Cut, Rolled, Brake-formed EDGES: Square, Smooth FASTENER: Weld rolled bracket to flat stock. Tamper-resistant mechanically fastened to post and Panel Bracket. 5. BREAKAWAY FOOTER FOOTER: The Transpo break-away system, according to specifications per NHDOT. 7'-6" 7'- 5/8" NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. '-0"min '-0" recommended SUBCONSULTANT 0 North Church Street Suite 08 West Chester, PA 980 T Front View: PARK.L SCALE: /" = '-0" 5 Back View: PARK.L SCALE: /" = '-0" Side View: PARK.L SCALE: /" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type PARK.L Parking Directional D.

35 SPECIFICATIONS SIGN TYPE: PARK. FUNCTION: Parking Lot ID. 4.5" SQUARE POST MATERIAL: Aluminum Square Tube " x 4.50" x.50" wall FABRICATION PROCESS: Extruded CORNERS: Square, Smooth COLOR: Custom, as noted FOOTER: As per NHDOT breakaway specs. Graffiti Vinyl Over-laminate. (See Color Sheet for all color and material specifications) FASTENER: Press-roll per M requirements. TOP PANEL GRAPHICS: Screen-printed (No reflective or opaque vinyl applications). CABINET FASTENERS: Hidden fasteners. 5. BREAKAWAY FOOTER FOOTER: The Transpo break-away system, according to specifications per NHDOT. 4 Top View: PARK. SCALE: /" = '-0" 4. CUSTOM FINIAL - ALL POSTS MATERIAL: Cast Aluminum CORNERS: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post.. DECORATIVE TOP BRACKET MATERIAL: Aluminum sheet - " wide x.60" wall (6 gauge) FABRICATION PROCESS: Router Cut, Rolled, Brake-formed EDGES: Square, Smooth FASTENER: Weld rolled bracket to flat stock. Tamper-resistant mechanically fastened to post and Panel Bracket. 4 /" '- /" '-5" 4 /" 9 /" F.7 5. PARKING SIGN CABINET MATERIAL: Aluminum sheet FABRICATION PROCESS: Extruded frame / Fabricated EDGES: Square, Smooth INFO PANELS AND COPY PROCESS: M custom inks print direct to 90 with M approved UV/ F.7 F.7 6'-0" '-" '-0"min '-0" recommended PORTSMOUTH Bridge St. Parking Lot PUBLIC PARKING No Overnight Parking Vehicles Will Be Towed P7 P 5 V 5 V 5 V5 5 P7 P5 PORTSMOUTH Bridge St. Parking Lot PUBLIC PARKING No Overnight Parking Vehicles Will Be Towed NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T '-0" Front View: PARK. SCALE: /" = '-0" P5 Side View: PARK. SCALE: /" = '-0" Back View: PARK. SCALE: /" = '-0" SUBCONSULTANT /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type PARK. Parking Lot Identification D.

36 HANOVER GARAGE PUBLIC PARKING Clearance 7'-" SPECIFICATIONS SIGN TYPE: PARK.4-7 FUNCTION: Parking Garage GARAGE PARKING Exit Only Entrance HANOVER GARAGE PUBLIC PARKING NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. Exit Only Entrance Clearance 7'-" 0 North Church Street Suite 08 West Chester, PA 980 T SUBCONSULTANT /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type PARK.5-8 Parking Garage D.4

37 SPECIFICATIONS SIGN TYPE: PARK.4-7 FUNCTION: Hanover Garage PARK.6 PARK.4 PARK.7 PARK.7 PARK.7 PARK.5 D.8 - D.9 - D.0 D.7 - D.0 0 /" NOTES Exit Only 6 " 6 " Exit Only Entrance Clearance 7' ". Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. SUBCONSULTANT 0 North Church Street Suite 08 West Chester, PA 980 T Front View: PARK.4-7 North Elevation SCALE: /6" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Hanover Garage North Elevation D.5

38 SPECIFICATIONS SIGN TYPE: PARK.4-7 FUNCTION: Hanover Garage PARK.7 PARK.6 PARK.7 PARK.4 - D.0 - D.9 - D.0 D.7 '-" Exit Only 6 " 6 " Entrance Clearance 7' " NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T SUBCONSULTANT Front View: PARK.4-7 West Elevation SCALE: /6" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Hanover Garage West Elevation D.6

39 SPECIFICATIONS SIGN TYPE: PARK.4 FUNCTION: Parking Garage ID 7. SIGN STRUCTURE Material: Aluminum Process: Fabricated/ Welded H type construction Surface Process: Paint as indicated Color: As indicated in Color Chart Internal Bracing: As reqd. by sign manufacturers Structural engineer. Fabricators drawings are to be signed and sealed by a certified State of NH licensed Structural Engineer. SIGN FACE Sign Panel: Flexible Face Clip Mounting System Vinyl: M Scotchcal Translucent Graphic Film as specified Diffuser: M Diffuser Film as specified Substrate: M Panaflex 945 as specified Color: As indicated in Color Chart '-" '-" P4 P P9 Detail: PARK.4 SCALE: NTS LED LIGHT FIXTURE Lighting Process: Internal Face Lit Manufacturer: Sylvania LED #OSDC6w-865- Exterior or approved equal. Color:White Fasten: Mount to inside of Logo, provide rear baffle at rear with second row of LEDs. LED HOUSING Material: Aluminum Process: Fabricated/ Welded H type construction Surface Process: Paint as indicated Color: As indicated in Color Chart Internal Bracing: As reqd. by sign manufacturers Structural engineer. Fabricators drawings are to be signed and sealed by a certified State of Florida licensed Structural Engineer. Recommend ' 4'-0" above Street or Sidewalk 5" '-" 6" Top View: PARK.4 SCALE: /" = '-0" HARDWARE MOUNTING METHOD: Mechanically Fasten MATERIAL: Stainless Steel TYPE: Screw with threaded anchor insert. SIZE: as determined by Fabricator MOUNTING SURFACE: Concrete or Brick VIF NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T SUBCONSULTANT Front View: PARK.4 SCALE: /8" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type PARK.4 Parking Garage ID D.7

40 SPECIFICATIONS SIGN TYPE: PARK.5 FUNCTION: Parking Garage ID 7. SIGN STRUCTURE Material: Aluminum Process: Fabricated/ Welded H type construction Surface Process: Paint as indicated Color: As indicated in Color Chart Internal Bracing: As reqd. by sign manufacturers Structural engineer. Fabricators drawings are to be signed and sealed by a certified State of NH licensed Structural Engineer. '-0" '- /4" SIGN FACE Sign Panel: Flexible Face Clip Mounting System Vinyl: M Scotchcal Translucent Graphic Film as specified Diffuser: M Diffuser Film as specified Substrate: M Panaflex 945 as specified Color: As indicated in Color Chart '- /" P P4 P LED LIGHT FIXTURE Lighting Process: Internal Face Lit Manufacturer: Sylvania LED #OSDC6w-865- Exterior or approved equal. Color:White Fasten: Mount to inside of Logo, provide rear baffle at rear with second row of LEDs. 6'-0 /" /" 6'-6" 4 /4" '-6 /" '-7 /" /" GARAGE PARKING P9 P6 Detail: PARK.5 SCALE: NTS '-0" 6" LED HOUSING Material: Aluminum Process: Fabricated/ Welded H type construction Surface Process: Paint as indicated Color: As indicated in Color Chart Internal Bracing: As reqd. by sign manufacturers Structural engineer. Fabricators drawings are to be signed and sealed by a certified State of Florida licensed Structural Engineer. HARDWARE MOUNTING METHOD: Mechanically Fasten MATERIAL: Stainless Steel TYPE: Screw with threaded anchor insert. SIZE: as determined by Fabricator MOUNTING SURFACE: Concrete or Brick VIF 5" Recommend ' 4'-0" above Street or Sidewalk 4 Top View: PARK.5 SCALE: /" = '-0" NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T SUBCONSULTANT Front View: PARK.5 SCALE: /8" = '-0" Side View: PARK.5 SCALE: /8" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type PARK.5 Parking Garage D.8

41 SPECIFICATIONS SIGN TYPE: PARK.6 FUNCTION: Wall Mounted Letters '- /" HANOVER GARAGE 0 /4" 8'-8" PUBLIC PARKING 9'-0" P 5. LETTERS Size: /8" Thk. MATERIAL: Aluminum FABRICATION PROCESS: Router Cut Fabricated Edges EDGES: Smooth FINISH: Horizontal Brushed SURFACE PROCESS: Satin Clearcoat FASTENER: mechanically fasten to existing wall. Anchor suitable for wall material. Allowable shear capacity of anchor = 0 lbs. (min). Anchors per anchor, Stud Mount Flush to wall surface. Graphic Layout: PARK.6 SCALE: /8" = '-0" /" '- /" NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T Section: PARK.6 SCALE: " = '-0" SUBCONSULTANT /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type PARK.6 Wall Mounted Letters D.9

42 SPECIFICATIONS SIGN TYPE: PARK.7 FUNCTION: Parking Garage Exit/Entry '-0" '-" 9" '-" 8 /4" 4 /4" 9'-0" Exit Only Entrance Clearance 7' " P P9 P P9 P P7 6. SIGN PANEL MATERIAL: /4 thk Aluminum FABRICATION PROCESS: Square Cut EDGES: Smooth FASTENER: Chemically Welded to Backer Panel BACKER PANEL MATERIAL: /8 thk Aluminum FABRICATION PROCESS: Square Cut to match dimensions of sign panel EDGES: Smooth FASTENER: mechanically fasten to existing wall. Anchor suitable for wall material. Allowable shear capacity of anchor = 50 lbs. (min). 8 Anchors, with anchor placed at each corner. Stud Mount Welded or countersunk to sign panel. COPY ARROW RULE BACKGROUND PRODUCT: M 90 Grade reflective sheeting per color chart MATERIAL: vinyl FABRICATION PROCESS: Digital Print direct to 90 UV clear Graphic Layout: PARK.7 SCALE: /8" = '-0" NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 9'-0" /4" /8" 0 North Church Street Suite 08 West Chester, PA 980 T Section: PARK.7 NTS SUBCONSULTANT /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type PARK.6 Parking Garage Exit/Entry D.0

43 SPECIFICATIONS SIGN TYPE: PARK.8 FUNCTION: LED Parking Sign 6" F. 5 Top View: PARK.8 SCALE: /" = '-0" 4'-9" PORTSMOUTH P7 P5 4 5'-" PARKING HANOVER GARAGE Alternate Message F.. 6" SQUARE POST MATERIAL: Aluminum Square Tube 606-6" x 6" x.50" wall FABRICATION PROCESS: Extruded CORNERS: Square, Smooth COLOR: Custom, as noted FOOTER: As per NHDOT breakaway specs. 4. CUSTOM FINIAL - ALL POSTS MATERIAL: Cast Aluminum CORNERS: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post.. DECORATIVE TOP BRACKET MATERIAL: Aluminum sheet - " wide x.60" wall (6 gauge) FABRICATION PROCESS: Router Cut, Rolled, Brake-formed EDGES: Square, Smooth FASTENER: Weld rolled bracket to flat stock. Tamper-resistant mechanically fastened to post and Panel Bracket. all color and material specifications) FASTENER: Press-roll per M requirements. TOP PANEL GRAPHICS: Screen-printed (No reflective or opaque vinyl applications). CABINET FASTENERS: Hidden fasteners. 0. LED SIGN CABINET MATERIAL: Aluminum sheet FABRICATION PROCESS: Extruded frame / Fabricated EDGES: Square, Smooth INFO PANELS AND COPY PROCESS: DAKTRONICS LED MODULE REF DETAILS SECTION FOR SPECIFICATIONS CABINET FASTENERS: Hidden fasteners. 5. BREAKAWAY FOOTER FOOTER: The Transpo break-away system, according to specifications per NHDOT. '-0 /" V F. V5 PARKING BRIDGE ST LOT P 5 V 5 0 P PARKING SIGN CABINET MATERIAL: Aluminum sheet FABRICATION PROCESS: Extruded frame / Fabricated EDGES: Square, Smooth INFO PANELS AND COPY PROCESS: M custom inks print direct to 90 with M approved UV/ Graffiti Vinyl Over-laminate. (See Color Sheet for 7'-0" P5 0'-8 /4" NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. '-0"min '-0" recommended 0 North Church Street Suite 08 West Chester, PA 980 T SUBCONSULTANT Front View: PARK.8 SCALE: /" = '-0" 5 Side View: PARK.8 SCALE: /" = '-0" Back View: PARK.8 SCALE: /" = '-0" 4 Side View: PARK.8 SCALE: /" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type PARK.8 LED Parking Sign D.

44 '-0" SPECIFICATIONS SIGN TYPE: PED. FUNCTION: Pedestrian Directional 5 Top View: PED. SCALE: /" = '-0" Hanover Garage Market Square Music Hall Post Office Prescott Park Seacoast Theatre Strawbery Banke Visitor Center WATERFRONT " /" " " /4" " /" '-0". 4.5" SQUARE POST MATERIAL: Aluminum Square Tube " x 4.50" x.50" wall FABRICATION PROCESS: Extruded CORNERS: Square, Smooth COLOR: Custom, as noted FOOTER: As per NHDOT breakaway specs. 4. CUSTOM FINIAL - ALL POSTS MATERIAL: Cast Aluminum CORNERS: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. EDGES: Square, Smooth FASTENER: Weld rolled bracket to flat stock. Tamper-resistant mechanically fastened to post and Panel Bracket in locations. Hanover Garage Market Square Music Hall Post Office Prescott Park Seacoast Theatre Strawbery Banke Visitor Center WATERFRONT F.0 P5 4 P7 '-0 /4" F.9 F.8 F.8 F.8 '-5 /8" F.0 P7 P P5 0'-7 7/8" '-0" 5 7/8" P 7 F.9 6 Hanover Garage Market Square Music Hall Post Office Prescott Park Seacoast Theatre Strawbery Banke Visitor Center WATERFRONT '-8" Graphic Layout: PED. SCALE: " = '-0" F.9 4 F.9 P 6 P 6 P8 6 P PANEL BRACKETS MATERIAL: /4" thick Aluminum sheet, with /" square Aluminum solid. FABRICATION PROCESS: Router Cut, Saw Cut, Plug and stitch-weld. EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 6. DECORATIVE CORNER SPACER MATERIAL: Aluminum Angle -.50" wall FABRICATION PROCESS: Extruded, Saw Cut EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post.. DECORATIVE TOP BRACKET MATERIAL: Aluminum sheet - " wide x.60" wall (6 gauge) FABRICATION PROCESS: Router Cut, Rolled, Brake-formed NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. '-0"min '-0" recommended SUBCONSULTANT 0 North Church Street Suite 08 West Chester, PA 980 T Front View: PED. SCALE: /" = '-0" Side View: PED. SCALE: /" = '-0" Back View: PED. SCALE: /" = '-0" 4 Side View: PED. SCALE: /" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type PED. Pedestrian Directional D.

45 SPECIFICATIONS SIGN TYPE: PED. FUNCTION: Pedestrian Directional /4" Existing Light Pole P7 4 P. SLEEVE MATERIAL: Aluminum U-channel (.60" wall) FABRICATION PROCESS: Extruded EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to sign panel. 5 " Top View: PED. SCALE: "='-0" 4. POLE STRAP ATTACHMENT PRODUCT: Band-It Band, or approved equal. MATERIAL: Type 0 SS SIZE: /4 inch FINISH: Stainless steel FASTENER: Ultra-Lok Free End clamps NOTE: Sign Contractor to coordinate the removal or movement of interfering existing signs on poles, with the city. /" '-" '-" P MAP GRAPHIC PANEL PRODUCT NAME: izone, 56 Charter Oak Drive, Suite 00, Temple, Texas 7650 (888) , info@ izoneimaging.com PRODUCT: Digital high pressure phenolic laminate (dhpl) GRAPHIC APPROVAL PROCESS: Submit x" sample section of typical project panel for image and color quality approval. WARRANTY PERIOD: Ten (0) years from product ship date. THICKNESS: /4 inch FINISH: Satin, including UV inhibiting top layer. FASTENER: Tamper-resistant mechanically fastened to center panel, at 6 locations. Map panel fits within frame area, minimal doubleface tape across back to stop bowing of panel. '-" MAP ARTWORK TBD '-6 /" '-0"min '-0" recommended MAP ARTWORK TBD Hanover Garage Market Square Music Hall Post Office Prescott Park Seacoast Theatre Strawberry Banke Visitor Center '-" 0 0 /" '-8 /" 5/8" 5/8" '-6 /" '-" /" Hanover Garage Market Square Music Hall Post Office Prescott Park Seacoast Theatre Strawberry Banke Visitor Center " 0 P NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T SUBCONSULTANT Front View: PED. SCALE: /" = '-0" Side View: PED. SCALE: /" = '-0" Back View: PED. SCALE: /" = '-0" 4 Graphic Layout: PED. SCALE: " = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type PED. Pedestrian Directional D.

46 SPECIFICATIONS SIGN TYPE: KIOSK. FUNCTION: Pedestrian Kiosk F. F. '-5" 5 Top View: KIOSK. SCALE: /" = '-0" '- /4" MARKET SQUARE 5 MINUTE WALK 6 - P7 P7 P 7 P5 8 6 F. MARKET SQUARE 5 MINUTE WALK Detail View: KIOSK. SCALE: /" = '-0" MARKET SQUARE F. 4 F. P 6 P 6. " SQUARE POST MATERIAL: Aluminum Square Tube " x " x.50" wall FABRICATION PROCESS: Extruded CORNERS: Square, Smooth COLOR: Custom, as noted FOOTER: As per NHDOT breakaway specs. 5. PANEL BRACKETS MATERIAL: /4" thick Aluminum sheet, with /" square Aluminum solid. FABRICATION PROCESS: Router Cut, Saw Cut, Plug and stitch-weld. EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post. 6. DECORATIVE CORNER SPACER MATERIAL: Aluminum Angle -.50" wall FABRICATION PROCESS: Extruded, Saw Cut EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to post.. DECORATIVE TOP BRACKET MATERIAL: Aluminum sheet - " wide x.60" wall (6 gauge) FABRICATION PROCESS: Router Cut, Rolled, Brake-formed EDGES: Square, Smooth FASTENER: Weld rolled bracket to flat stock. Tamper-resistant mechanically fastened to post and Panel Bracket in locations. NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 7. KIOSK CENTER PANEL MATERIAL: /4" thick Aluminum sheet FABRICATION PROCESS: Router Cut EDGES: Square, Smooth FASTENER: Plug-weld into posts. 8. MAP GRAPHIC PANEL PRODUCT NAME: izone, 56 Charter Oak Drive, Suite 00, Temple, Texas 7650 (888) , info@ izoneimaging.com PRODUCT: Digital high pressure phenolic laminate (dhpl) GRAPHIC APPROVAL PROCESS: Submit x" sample section of typical project panel for image and color quality approval. WARRANTY PERIOD: Ten (0) years from product ship date. THICKNESS: /4 inch FINISH: Satin, including UV inhibiting top layer. FASTENER: Tamper-resistant mechanically fastened to center panel, at 6 locations. Map panel fits within frame area, minimal doubleface tape across back to stop bowing of panel. F. Hanover Garage. mi Market Square. mi Music Hall. mi Post Office.4 mi Prescott Park.5 mi Seacoast Theatre.5 mi Strawberry Banke.7 mi Visitor Center.5 mi P5 7'-5" Hanover Garage Market Square Music Hall Post Office Prescott Park Seacoast Theatre Strawberry Banke Visitor Center F.. mi. mi. mi.4 mi.5 mi.5 mi.7 mi.5 mi P8 6 P4 6 SUBCONSULTANT 0 North Church Street Suite 08 West Chester, PA 980 T '-6 /4" Front View: KIOSK. SCALE: /" = '-0" Side View: KIOSK. SCALE: /" = '-0" Back View: KIOSK. SCALE: /" = '-0" 4 Side View: KIOSK. SCALE: /" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type KIOSK. Pedestrian Kiosk D.4

47 SPECIFICATIONS SIGN TYPE: PLAQUE. FUNCTION: Sidewalk Plaque Flush Flush /8" /8" Weld metal U channel to back of plaque Epoxy both sides '-6" '- /4" 9 /4" WATERFRONT /" PRESCOTT PARK. COMPASS PLAQUE MATERIAL: /8" thick cast bronze FABRICATION PROCESS: Cast bronze COLOR: Natural. SURFACE PROCESS: None. NO clear coat. EDGES: Square and smooth. MOUNTING: Core drilled into existing concrete sidewalk or pavers. Top surface of plaque MUST BE flush with existing concrete surface. Weld metal U Channel to back of plaque. Epoxy both sides " 6" /" (mw) Existing Concrete New Concrete T H E D E C K S 4 S T R AW B E R Y B A N K E Graphic Layouts: PLAQUE. SCALE: " = '-0" Section: PLAQUE. SCALE: NTS MARKET SQUARE 9 /4" N O R T H C H U RC H x xx '-6" '- /4" MARKET N O R T H SQUARE CH U RCH /" Preferred Option: Replace entire concrete pad area/section. Alternate: When sidewalk is not cracked or in disrepair, core drill within /4" tolerance. Note: Owner will locate in field. NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T SUBCONSULTANT Front Elevation: PLAQUE. SCALE: / "= '-0" Elevation: PLAQUE. SCALE: /" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type PLAQUE. Sidewalk Plaque D.5

48 P P4 P xx xx SPECIFICATIONS SIGN TYPE: KIOSK. FUNCTION: Market Square Kiosk. SLEEVE MATERIAL: Aluminum U-channel (.60" wall) FABRICATION PROCESS: Extruded EDGES: Square, Smooth FASTENER: Tamper-resistant mechanically fastened to sign panel. P6 P8 Top View: KIOSK.a-b SCALE: /" = '-0" " 8" 8" " /" INFORMATION PORTSMOUTH 5 MINUTE WALK P6 P7 P0 P9 P 0 /4" NOTES '-0" Hanover Garage Market Square Music Hall Post Office Prescott Park Seacoast Theatre Strawberry Banke Visitor Center. mi. mi. mi.4 mi.5 mi.5 mi.7 mi.5 mi Side View: KIOSK.a-b SCALE: /" = '-0". Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. '-5 /" 0 North Church Street Suite 08 West Chester, PA 980 T SUBCONSULTANT Front View: KIOSK.a-c SCALE: /" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type KIOSK. Market Square Kiosk D.6

49 SPECIFICATIONS SIGN TYPE: REG. FUNCTION: Regulatory Sign Top View: REG. SCALE: " = '-0" 8. SIGN PANEL BACKS - PAINT..5" SQUARE POST MATERIAL: Aluminum Square Tube " x " x.50" wall FABRICATION PROCESS: Extruded CORNERS: Square, Smooth COLOR: Custom, as noted FOOTER: As per NHDOT breakaway specs.. Breakout Square Coupler Varies P7 8 Varies 95 Varies P5 NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 7'-0" '-0" min '-0" recommended '-0" 0 North Church Street Suite 08 West Chester, PA 980 T SUBCONSULTANT Front View: REG. SCALE: /" = '-0" Back View: REG. SCALE: /" = '-0" Breakout Square Coupler 4 Detail: REG. NTS /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type REG. Regulatory Sign D.7

50 SPECIFICATIONS SIGN TYPE: REG. FUNCTION: Regulatory Sign Top View: REG. SCALE: " = '-0" 8. SIGN PANEL BACKS - PAINT..5" SQUARE POST MATERIAL: Aluminum Square Tube " x " x.50" wall FABRICATION PROCESS: Extruded CORNERS: Square, Smooth COLOR: Custom, as noted FOOTER: As per NHDOT breakaway specs.. Breakout Square Coupler 4. Bracket Varies P7 8 P5 4 Varies NOTES. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. '-0" min '-0" recommended P5 0 North Church Street Suite 08 West Chester, PA 980 T SUBCONSULTANT Front View: REG. SCALE: /" = '-0" Back View: REG. SCALE: /" = '-0" Breakout Square Coupler 4 Detail: REG. NTS /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Type REG. Regulatory Sign D.8

51 E Graphic Layouts

52 '- /" " 4" 5" " " '-0" S Artspace Graphic Layouts: VDIR. SCALE: /4" = '-0" " Strawbery Banke 5'-7 /" " 4" '-0" " Message Message " 4" " 4" 7" Destination Message Destination Message SPECIFICATIONS SIGN PANEL LAYOUTS: VDIR. Messages shown are NOT actual messages. Provided for illustrative purposes only. Refer to message schedule for actual sign messages. Panel layouts for ALL sign locations shall be included in shop drawings for review by designer and client. " 4" '-0" " " Downtown Municipal Complex Message 5 /4" " Destination Message /" 5" " 6 /" /" 4'-5 /" /4" 4" " 4 /4" 7" " City Hall Public Parking Strawbery Banke 5" " Waterfront Message Message Message " 4" 7" 4" " 5 /4" " Downtown Strawbery Banke Municipal Complex Market Square Hanover Garage Isles of Shoals Ferry. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. 0 North Church Street Suite 08 West Chester, PA 980 T VDIR.- Graphic Layouts Graphic Layouts: VDIR. SCALE: /4" = '-0" Graphic Layouts: VDIR. SCALE: /4" = '-0" E.

53 SPECIFICATIONS '- /" 7" 6" 6" 6" /" 6" " 7'-5" Indoor Pool Downtown/ Waterfront 5'-0" '-8" '-8" '-8" 6" " 6" " 7'-5" Pease Intl. Tradeport Pease Golf Course Transportation Center /" /" 9 /4" SIGN PANEL LAYOUTS: VDIR.4-6 Messages shown are NOT actual messages. Provided for illustrative purposes only. Refer to message schedule for actual sign messages. Panel layouts for ALL sign locations shall be included in shop drawings for review by designer and client. '- /" 6" /" '- /" 7" 6" '-" '-5" /" '- /" /" 6" 7" '- /" '-5" '-" '- /" " Destination Beaches Graphic Layouts: VDIR.4 SCALE: /" = '-0" Destination Message Message Message Message Message 7'-5" /" /" '-" '-" '-" '-" '-6 /" '-6 /" Destination Message Destination Message Destination Destination Message Destination Destination Graphic Layouts: VDIR.6 SCALE: /" = '-0" /" /" /" /". Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. 0 North Church Street Suite 08 West Chester, PA 980 T VDIR.4-6 Graphic Layouts Graphic Layouts: VDIR.5 SCALE: /" = '-0" E.

54 SPECIFICATIONS SIGN PANEL LAYOUTS: PARK. Messages shown are NOT actual messages. Provided for illustrative purposes only. Refer to message schedule for actual sign messages. Panel layouts for ALL sign locations shall be included in shop drawings for review by designer and client. '-" Ø '-0 /8" Ø 0 /8" Ø 9 /4" " 6" 6" '-0" '-" 0" " 4 /" 5 /4". Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T Graphic Layouts: PARK. SCALE: /" = '-0" /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. PARK. Graphic Layouts E.

55 /" '-0" SPECIFICATIONS SIGN PANEL LAYOUTS: PARK. Messages shown are NOT actual messages. Provided for illustrative purposes only. '- /" /4" 4 /4" /4" Bridge St. Lot Market Hanover Lot South Mill Pond Lot Refer to message schedule for actual sign messages. Panel layouts for ALL sign locations shall be included in shop drawings for review by designer and client. 0" 5 /" /4" City Hall Lower Lot Market St. Church Lot Vaughan St. Lot City Hall Upper Lot Memorial Bridge Lot Worth Lot. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. Court St. Parking Area Parrott Ave. Lot Hanover Garage Alternate Layout /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. 0 North Church Street Suite 08 West Chester, PA 980 T PARK. Graphic Layouts Graphic Layouts: PARK. SCALE: /4" = '-0" E.4

56 SPECIFICATIONS '-6 /4" 4" /4" SIGN PANEL LAYOUTS: PARK. 6 /4" 4 /" /4" 4" " /4" /4" /4" /" Bridge St. Lot PUBLIC PARKING No Overnight Parking Vehicles Will Be Towed '-" /4" Market Hanover Lot PUBLIC PARKING No Overnight Parking Vehicles Will Be Towed South Mill Pond Lot PUBLIC PARKING No Overnight Parking Vehicles Will Be Towed Masonic Temple Lot PUBLIC PARKING No Overnight Parking Vehicles Will Be Towed Messages shown are NOT actual messages. Provided for illustrative purposes only. Refer to message schedule for actual sign messages. Panel layouts for ALL sign locations shall be included in shop drawings for review by designer and client. City Hall Lower Lot EMPLOYEE PARKING Public Parking Weekends Only Market St. Church Lot PUBLIC PARKING No Overnight Parking Vehicles Will Be Towed Vaughan St. Lot PUBLIC PARKING No Overnight Parking Vehicles Will Be Towed Rock St. Lot PUBLIC PARKING No Overnight Parking Vehicles Will Be Towed City Hall Upper Lot PUBLIC PARKING No Overnight Parking Vehicles Will Be Towed Memorial Bridge Lot PUBLIC PARKING No Overnight Parking Vehicles Will Be Towed Worth Lot PUBLIC PARKING No Overnight Parking Vehicles Will Be Towed. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T Court Street Parking Area PUBLIC PARKING No Overnight Parking Vehicles Will Be Towed Parrott Ave. Lot PUBLIC PARKING No Overnight Parking Vehicles Will Be Towed Worth Lot PUBLIC PARKING No Overnight Parking Vehicles Will Be Towed These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. /8/0 PARK. Graphic Layouts Graphic Layouts: PARK. SCALE: /4" = '-0" Reverse Layout E.5

57 SPECIFICATIONS '-4 /4" '-4 /4" '-4 /4" 4'- /4" 5'- /4" '-0 /4" VDIR. VDIR. VDIR. '-4 /4" '-4 /4" '-4 /4" 4'- /4" 5'- /4". Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. '-0 /4" VDIR. VDIR. VDIR. 5'-4 /4" 0 North Church Street Suite 08 West Chester, PA 980 T '-4 /4" /8/0 '-0" 5'-4 /4" '- /" 4'- /4" These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Art Panels VDIR.4 VDIR.5 VDIR.6 E.6

58 F Construction Details

59 /4" 4 /" '-0" '-0" SPECIFICATIONS For sign types: VDIR. VDIR. VDIR. " Section View: Vehicular Directional SCALE: " = " /4" 4 /" Section View: Vehicular Directional SCALE: " = ". Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. /4" 4 /" '-0" 0 North Church Street Suite 08 West Chester, PA 980 T '-8" /8/0 " These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Drawing Description Section View: Vehicular Directional SCALE: " = " F.

60 " " /4" 4 /" " SPECIFICATIONS For sign types: VDIR. VDIR. VDIR. " '- /4" 6 /4" Section View: Cast Cap SCALE: " = " '- /4" 4" " 4" " 9 /" P. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. '-0 /" Side View: Decorative Top Bracket SCALE: " = " Side View: Decorative Bottom Bracket SCALE: " = " 6 /" P 0 North Church Street Suite 08 West Chester, PA 980 T /8/0 " /" P8 P4 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Drawing Description 4 Side View: Panel Bracket SCALE: " = " F.

61 5 /4" 5 /" 5 /" 5 /4" SPECIFICATIONS For sign types: VDIR.4 VDIR.5 VDIR.6 Section View: Vehicular Directional SCALE: " = " Section View: Vehicular Directional SCALE: " = ". Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T /8/0 Section View: Vehicular Directional SCALE: " = " These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Drawing Description F.

62 SPECIFICATIONS 4" 4" 6" 4" For sign types: VDIR.4 VDIR.5 VDIR.6 /4" " " '-" Section View: Cast Cap SCALE: " = " 4" '-" " 9 /" P. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. Side View: Decorative Top Bracket SCALE: " = " Side View: Decorative Bottom Bracket SCALE: " = " '-0 /" 6 /4" P 0 North Church Street Suite 08 West Chester, PA 980 T /8/0 " /" P P These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Drawing Description 4 Side View: Panel Bracket SCALE: " = " F.4

63 SPECIFICATIONS For sign types: PARK. '-0" /4" 4 /" 6" " Section View: Parking Directional SCALE: " = " /4" 4 /". Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. /4" 4 /" Section View: Parking Directional SCALE: " = " '-0" '-8" /8/0 0 North Church Street Suite 08 West Chester, PA 980 T " These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Drawing Description Section View: Parking Directional SCALE: " = " F.5

64 4" 4 /" " SPECIFICATIONS For sign types: PARK. /4" 4" Section View: Cast Cap SCALE: " = " 7 /4" 4" 8 /" " 9 /" P. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. Side View: Decorative Top Bracket SCALE: " = " Side View: Decorative Bottom Bracket SCALE: " = " '-0 /" 6 /" P 0 North Church Street Suite 08 West Chester, PA 980 T /8/0 " /" P8 P4 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Drawing Description 4 Side View: Panel Bracket SCALE: " = " F.6

65 SPECIFICATIONS For sign types: PARK. 5 /" 4 /" Section View: Parking Lot ID SCALE: " = " 5 /" 4 /" Section View: Parking Lot ID SCALE: " = ". Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. /4" 6" 4" 0 North Church Street Suite 08 West Chester, PA 980 T /8/0 Section View: 4 / CAP SCALE: " = " These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Drawing Description F.7

66 SPECIFICATIONS For sign types: PED. 4 /" Section View: Pedestrian Directional SCALE: " = " 4 /" Section View: Pedestrian Directional SCALE: " = ". Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T /" Section View: Pedestrian Directional SCALE: " = " /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Drawing Description F.8

67 4 /4" 4 /" " SPECIFICATIONS For sign types: PED. /4" 4 /4" Section View: Cast Cap SCALE: " = " '-0 /4" 5" " " 6" 9 /" P. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. '-0 /" Side View: Decorative Top Bracket SCALE: " = " Side View: Decorative Bottom Bracket SCALE: " = " 6 /" P 0 North Church Street Suite 08 West Chester, PA 980 T /8/0 " /" P8 P4 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Drawing Description 4 Side View: Panel Bracket SCALE: " = " F.9

68 " '-0" SPECIFICATIONS For sign types: PED. '-0 /4" '-" Hanover Garage Front View: Decorative Top Bracket SCALE: " = ". Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. Visitor Center 0 North Church Street Suite 08 West Chester, PA 980 T /8/0 6 /4" WATERFRONT '-8" /" These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Drawing Description Side View: Decorative Bottom Bracket SCALE: " = " F.0

69 SPECIFICATIONS For sign types: KIOSK. '-0 /" 4 /" " Section View: Kiosk SCALE: " = " '-8 /" 4 /" /4" " Section View: Kiosk SCALE: " = " '-8 /4". Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 4 /" /4" " 0 North Church Street Suite 08 West Chester, PA 980 T /8/0 Section View: Kiosk SCALE: " = " These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Drawing Description F.

70 4 /4" 4 /" " 5" SPECIFICATIONS For sign types: KIOSK. /4" '-0 /4" Section View: Cast Cap SCALE: " = " '-4 /4" " P Side View: Decorative Top Bracket SCALE: " = " 0 /". Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. P 0 North Church Street Suite 08 West Chester, PA 980 T " /4" Side View: Decorative Bottom Bracket SCALE: " = " 4 Side View: Panel Bracket SCALE: " = " 5" 6" P8 P4 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. /8/0 Sign Drawing Description F.

71 SPECIFICATIONS For sign types: PARK.8 6" Section View: PARK.8 SCALE: " = " 5" VMS LED Message Panel VMS LED Arrow Panel 6" Section View: PARK.8 SCALE: " = " Power Supply. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. /4" 6" 4" Section View: Cast Cap SCALE: " = " These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. /8/0 0 North Church Street Suite 08 West Chester, PA 980 T Sign Drawing Description F.

72 SPECIFICATIONS '-0" '-0" /" /4" Side View: Decorative Top Bracket SCALE: " = ". Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T /8/0 /4" " /4" '-8 /4" These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Sign Drawing Description Side View: Decorative Bottom Bracket SCALE: " = " F.4

73 SPECIFICATIONS GALAXY DISPLAY AF-00 SERIES TECHNICAL SPECIFICATIONS GALAXY DISPLAY AF-00 SERIES Pixel pitch: Color capability: LEDs per pixel: Estimated LED lifetime: Viewing angle: Contrast enhancement: Service access: Graphic capability: Control software: Power: Display dimming: Communication options: Compliance information: 8 mm (0.") center-to-center;,600 pixels per sq ft mm (0.47") center-to-center; 646 pixels per sq ft color (amber or red) tricolor (red, amber, green)(8mm only) -in- 00,000 + hours 0 horizontal x 0 vertical Contrast enhancing polycarbonate face Front access Text, graphics, logos, basic animation, multiple font styles and sizes Venus 500 software or third-party integrators using Venus 500 SDK 0 or 40 VAC single phase 64 levels (automatic or manual control) RS, RS4 and Ethernet (wired or fiber) UL listed, NEMA R cabinet Galaxy AF-00 series displays provide instant control of the traffic/pedestrian flow in your facility. Small outdoor character displays minimize customer confusion with dynamic text, graphics, logos and animation visible at up to 50 feet. Customers will notice and use your convenient network of displays. The AF-00 increases revenue in parking garages, airports, convention centers, and many other locations by: Directing traffic flow and offering payment instructions at entrances and exit plazas Providing way finding in all parts of parking lots and any facility Diminishing vehicle circulation congestion Displaying courtesy messages and advertising FEATURES AND BENEFITS Visibility 0 viewing angle and a range of character sizes from. to 4.4 supports ADA requirements and provides readability and flexible content Reduces glare and improves contrast and legibility with contrast enhancing polycarbonate Communication RS-, RS-4, or Ethernet (wired or fiber) communication options allow for flexible installation Venus 500 controller easily integrates with existing software used by most system integrators Ask about our Software Developers Kit (SDK). Protection and Maintenance Vandal and tamper resistant cabinet An application of conformal coating to all electronic components grants protection from harsh environmental conditions and dust Easy access and trouble-free maintenance of all components; modules are mounted to the inner side of a swing down, front access door MODEL SPECIFICATIONS MODEL NUMBER CABINET (HXWXD) LINES/ CHAR. PER LINE CHARACTER HEIGHT WEIGHT (LBS) POWER (WATTS) 0 VAC AF-00-6x96-8-A, R, or RG 0" x '0" x 5" / AF-00-6x44-8-A, R, or RG 0" x 4'" x 5" / AF-00-6x9-8-A, R, or RG 0" x 5'" x 5" / AF-00-6x40-8-A, R, or RG 0" x 6'5" x 5" / AF-00-x96-8-A, R, or RG '" x '0" x 5" 4/ AF-00-x44-8-A, R, or RG '" x 4'" x 5" 4/ AF-00-x9-8-A, R, or RG '" x 5'" x 5" 4/ AF-00-x40-8-A, R, or RG '" x 6'5" x 5" 4/ AF-00-48x96-8-A, R, or RG '7" x '0" x 5" 6/ AF-00-48x44-8-A, R, or RG '7" x 4'" x 5" 6/ AF-00-48x9-8-A, R, or RG '7" x 5'" x 5" 6/ AF-00-48x40-8-A, R, or RG '7" x 6'5" x 5" 6/ AF-00-8x96--A or R 9" x 4'" x 5" / AF-00-8x44--A or R 9" x 6'" x 5" / AF-00-6x96--A or R ' x 4'" x 5" / AF-00-6x44--A or R ' x 6'" x 5" / MODEL NUMBER GUIDE AF-00-6x96-8-RG SERIES NUMBER A=MATRIX F=OUTDOOR PIXEL PIXEL ROWS COLUMNS PIXEL SPACING (MM) Notes. Nominal character heights and number of lines that fit on each display are calculated using 7-pixel-high fonts. Many other font sizes are available. Contact Daktronics for details about other fonts.. The number of characters per line is calculated using a fixed-width 7-pixel-high by 5-pixel-wide font and one pixel separator between characters. LED COLOR. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T Prince Drive PO Box 50 Brookings, SD tel x57060 fax transportation@daktronics.com Copyright 0 Daktronics DD8989 Rev These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. /8/0 PARK.8 LED Details F.5

74 SPECIFICATIONS For sign types: VDIR. VDIR. VDIR. PARK.. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Break Away Footer F.6

75 SPECIFICATIONS Note: Design Wind load 00 PSF 90 MPH, Sec Gust Wind, Exp C 5" sidewalks 7" driveways '-0" Minimum Aluminum Post Transpo AS4 Break-Safe Break Away Sign Support Typ. Vertical and Horizontal Rebar as Required. Existing Concrete Slab Note: Design Wind load 00 PSF 90 MPH, Sec Gust Wind, Exp C '-0" Minimum 4" Aluminum Post Transpo AS4 Break-Safe Break Away Sign Support Existing Pavers Typ. Vertical and Horizontal Rebar as Required. The FABRICATOR shall be familiar with all site conditions and shall be responsible for all underground utility checks. The FABRICATOR shall be familiar with all basement/ vault locations by obtaining plans from the local municipality Department of Public Works. Where a basement/vault interferes with a proposed location. The sign shall be relocated to a location deemed appropriate by the municipalities Department of Public Works Where relocation is not an option the FABRICATOR will develop the appropriate mounting solution. The solution shall meet all engineering criteria as established by the standard footings. (i.e. windloads) Final designs and shop drawings shall be supplied by the fabricator for each of the Break-away poles identified and a New Hampshire Registered Professional Engineer is required to sign and seal the submittal of shop drawings. NOTE: ) soil is average with maximum allowable soil pressure of,000 pounds per square foot. Soil unit weight of 5 PCF and friction angle of 0 degrees (assumed). '-0" Minimum Class B Concrete Footing Reference State DOT Req. Standards '-0" Minimum Class B Concrete Footing Reference State DOT Req. Standards ) concrete Strength at 8 days f c=4,000 psi Reinforcement shall be ASTM 6 Fy=60,000 PSI ) FOLLOW 008 AHTD DESIGN STANDARDS FOR MATERIAL AND CONSTRUCTION INFORMATION FOR THE SIGN POST BASES AND FOUNDATIONS NOT OTHERWISE SPECIFIED IN THESE CONTRACT DRAWINGS Section View: Concrete SCALE: /4" = '-0" Section View: Pavers SCALE: /4" = '-0" 4) FOR SIGN POST SIZES REFER TO THE DESIGN INTENT DRAWING SHEETS Note: Design Wind load 00 PSF 90 MPH, Sec Gust Wind, Exp C 5" sidewalks 7" driveways Aluminum Post Transpo AS4 Break-Safe Break Away Sign Support Existing Concrete Slab Note: Design Wind load 00 PSF 90 MPH, Sec Gust Wind, Exp C 5" sidewalks 7" driveways Existing Concrete Slab Aluminum Post Transpo AS4 Break-Safe Break Away Sign Support Typ. Vertical and Horizontal Rebar as Required.. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T '-0" '-0" square Section View: Foundation: Shallow Depth SCALE: /4" = '-0" Typ. Vertical and Horizontal Rebar as Required. Class B Concrete Footing Reference State DOT Req. Standards '-" 4 4'-0" square Section View: Foundation: Extremely Shallow Depth SCALE: /4" = '-0" Class B Concrete Footing Reference State DOT Req. Standards These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. /8/0 Standard Footer Construction Details F.7

76 SPECIFICATIONS For sign types: VDIR.4 VDIR.5 VDIR.6. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T /8/0 These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Break Away Footer F.8

77 SPECIFICATIONS Note: Design Wind load 00 PSF 90 MPH, Sec Gust Wind, Exp C Aluminum Post. Size varies, reference design details for exact size. Note: Design Wind load 00 PSF 90 MPH, Sec Gust Wind, Exp C Aluminum Post. Size varies, reference design details for exact size. 5" sidewalks 7" driveways '-0" Minimum Transpo B55 Break-Safe Break Away Sign Support Typ. Vertical and Horizontal Rebar as Required. Existing Concrete Slab '-0" Minimum 4" Transpo B55 Break-Safe Break Away Sign Support Existing Pavers Typ. Vertical and Horizontal Rebar as Required. '-0" Minimum Class B Concrete Footing Reference State DOT Req. Standards '-0" Minimum Class B Concrete Footing Reference State DOT Req. Standards 5" sidewalks 7" driveways '-0" Note: Design Wind load 00 PSF 90 MPH, Sec Gust Wind, Exp C Section View: Concrete SCALE: /4" = '-0" '-0" square Aluminum Post. Size varies, reference design details for exact size. Transpo B55 Break-Safe Break Away Sign Support Section View: Foundation: Shallow Depth SCALE: /4" = '-0" Existing Concrete Slab Typ. Vertical and Horizontal Rebar as Required. Class B Concrete Footing Reference State DOT Req. Standards 5" sidewalks 7" driveways '-" Note: Design Wind load 00 PSF 90 MPH, Sec Gust Wind, Exp C 4 Existing Concrete Slab Section View: Pavers SCALE: /4" = '-0" 4'-0" square Aluminum Post. Size varies, reference design details for exact size. Transpo B55 Break-Safe Break Away Sign Support Typ. Vertical and Horizontal Rebar as Required. Section View: Foundation: Extremely Shallow Depth SCALE: /4" = '-0" Class B Concrete Footing Reference State DOT Req. Standards. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. /8/0 0 North Church Street Suite 08 West Chester, PA 980 T Standard Footer Construction Details F.9

78 SPECIFICATIONS Existing sidewalk block to be removed and replaced Sign Post Footer to be removed, saved and replaced. Sign Post Footer NOTE: When locating a footer within a single pavement block adjacent to at least expansion joints, the entire block of pavement shall be removed and replaced with the same materials and finish of adjacent sidewalk areas. Plan: Footer Placement SCALE: NTS NOTE: The pattern of bricks need to be removed, stored and replaced in the order they were removed. Marking the Specialty Pavers sidewalk with spray paint will NOT be allowed. Plan: Specialty Pavers Footer Placement SCALE: NTS Varies CL Varies CL Class B Concrete Footing Reference State DOT Req. Standards Transpo Break-Safe, or Transpo Pole-Safe Break-Away System Sign Post Preferred Footer Detail BAD Footer Detail. Fabricator to verify the mounting conditions and provide a detail drawing for each mounting situation, prior to fabrication. Fabricator must obtain approval from the Designer or Client for placement prior to fabrication.. Welds: All welds shall be ground smooth, paint all seams.. Hardware: All exposed hardware shall be tamper proof fasteners. 0 North Church Street Suite 08 West Chester, PA 980 T /8/0 Plan View: Footer SCALE: " = ' - 0" Preferred Footer Detail BAD Footer Detail These drawings are meant for DESIGN INTENT ONLY and are not for construction. Contractor shall verify and be responsible for all dimensions and conditions of the job. Contractor shall be familiar with the site and conditions it presents. This office must be notified of any variations from the dimensions and conditions details must be submitted to this office for approval prior to proceeding with fabrication. All copy shall be proofread by client and legal requirements checked by legal department. Footer Placement Preferred Footer Detail BAD Footer Detail F.0