CHAPTER TWO Fire Lanes & Fire Access
|
|
|
- Jocelyn Lee
- 6 years ago
- Views:
Transcription
1 Contents: CHAPTER TWO Fire Lanes & Fire Access Access Requirements for New Construction Sites Fire Lane Signs and Installations Alternative Fire Lane Signs Fire Lane Identification (Red Painted Curbs) Alternative Surface Fire Apparatus Roads Blue Reflective Markers Purpose: Proper fire lanes directly affect how the Fire Department is able to maneuver through a property. These fire lane standards help to ensure unimpeded access for the fire apparatus.
2 ACCESS REQUIREMENTS FOR NEW CONSTRUCTION SITES Early Construction Phase 1. Signage shall read FIRE DEPARTMENT ACCESS and shall include site address, or range of addresses, for all commercial sites and residential model homes. a. Size. The two-sided sign plate shall be a minimum of 4x4 feet with a thickness of ¾ inch graded plywood. b. Color. The sign shall be two-sided, and have a red background with a white legend. c. Location. Signs shall be installed at each point of entry. 2. One (1) Temporary FD Access road shall be provided prior to vertical construction of structures. a. The access road shall be a minimum of twenty feet wide with a vertical clearance of 13 feet 6 inches. b. Turning radii shall be 42 feet 8 inches minimum outside radius, 20 feet 3 inches maximum inside radius (WB-40). c. Fire Department access road shall be designed and maintained by the contractor/builder at all times during construction. Access road shall be within 200 feet of all portions of the facility or all portions of the exterior walls of the first story of the building as measured by an approved route around the exterior of the building or facility. d. If more than one story, the access road must be within 200 feet of the center of the furthest room on the second floor or level from the access road for buildings with two or more floors. Travel shall be measured along normal pedestrian routes. One flight of stairs shall count as 30 feet and shall be a minimum of 44 inches wide. Dead end fire access roads that exceed 150 feet in length require an approved turnaround. e. A road surface made up of ABC or other approved materials compacted to 90% and capable of supporting fire apparatus vehicles 75,000-pound gross vehicle weight (GVW) under any weather condition. The temporary all weather surface shall be maintained by the builder for intended use by the Fire Department during the construction process. 3. One (1) hydrant must be operational and accessible prior to combustibles being delivered on site. a. Hydrants shall be located so that they are not more than a 400 feet hose lay away from combustible construction. Distance is measured as the fire truck travels, not line of sight. Chapter 2-1
3 TEMPORARY FIRE DEPARTMENT CONSTRUCTION ACCESS SIGN SAMPLES FIRE DEPT ACCESS 1815 W INA RD Chapter 2-2
4 FIRE ACCESS SUBMITTAL REQUIREMENTS Three (3) 24 x 36 copies of SITE PLAN or FINAL PLAT showing the location of shall be submitted for review and approval at time of initial building plan submittals. Project name and location Property lines and construction area Cross streets and intersections Emergency vehicle access sign location A minimum of one (1) point of access is required Access road is a minimum of 20 feet wide with a minimum vertical clearance of 13 feet 6 inches Turning radius with 42 feet 8 inches minimum outside radius and 20 feet 3 inches maximum inside radius A minimum of one (1) approved fire hydrant capable of supplying the required fire flow is required within 400 feet travel distance of all combustibles The following statements must be noted on the plans: Access roads will be designed and maintained by the contractor/builder Access surface will be ABC compacted to support 75,000 lbs. **ALL FIRE INSPECTIONS REQUIRE MINIMUM ADVANCE NOTICE OF TWO BUSINESS DAYS** A re-inspection fee shall be assessed for failed or incomplete inspections. Chapter 2-3
5 FIRE LANE SIGNS NOTES: 1. The sign plate shall be a minimum of 12 X 18 inches with a thickness of.080 aluminum construction. 2. The sign face shall have a white reflective background with a red legend. Use the standard 3M Scotchlite sign face number R7-32 or equivalent, with red screen printed lettering as shown above. Chapter 2-4
6 ALTERNATIVE APPLICATION FIRE LANE SIGNS NOTES: 1. The sign plate shall be a minimum of 12 X 18 inches with a thickness of.080 aluminum construction. 2. The sign face shall have a white reflective background with a red legend. Use the standard 3M Scotchlite sign face number R7-32 or equivalent, with red screen printed lettering as shown above. Chapter 2-5
7 FIRE LANE SIGN AND POST INSTALLATION SPECIFICATIONS Recommended materials for installation: foot long U-Channel galvanized or painted post. 2. Fire Sign (12x18 inch).80 aluminum construction with white reflective background and red screen printed legend 3. ¼ bolts and nuts large flat or fender washers 4. Sign MUST FACE the ONCOMING TRAFFIC 5. Post shall be installed 12 to 18 inches from back of curb or back of sidewalk. 6. Northwest Fire District recommends you blue stake before you dig. Chapter 2-6
8 APPROVED FIRE LANE SIGN POSTS NOTES: 1. Approved signs shall be constructed of.080 aluminum with a reflective background. 2. Minimum of ¼ bolts with flat washers and nuts that bolt through. 3. Post footing shall be 12 inches in diameter and 18 inches in depth. 4. The sign shall be located seven (7) feet above finished grade to bottom of sign. 5. Fire lane sign shall be installed 12 to 18 inches from back of curb or back of sidewalk. 6. Signs MUST FACE the ONCOMING TRAFFIC. Chapter 2-7
9 WALL MOUNT BRACKET FIRE LANE SIGN FLAG-MOUNT STYLE NOTES: 1. 3/16-inch-thick, 2X3X15¾ inch aluminum angle bracket. 2. The sign plate shall be a minimum of 12x18 inches with a thickness of.080 aluminum construction 3. Approved sign bracket is available for flag-mounted FD access signs. Bracket can be used on either the right or left side of the sign. 4. This application only available when sign cannot be installed on an approved post. Chapter 2-8
10 FIRE LANE IDENTIFICATION, STENCILING AND SIGN INSTALLATION Signs only NOTES: 1. Approved fire lane signs shall be installed 12 to 18 inches from back of curb or back of sidewalk. 2. Sign MUST FACE the ONCOMING TRAFFIC. 3. Stencils shall be in white lettering (4-inch height, ½ inch stroke) on Industrial grade safety red painted curb. 4. Stencil shall read Fire Lane No Parking. Chapter 2-9
11 DESIGNER FIRE LANE SIGNS NOTES: 1. The sign plate shall be a minimum of 12 x 18 inches with a thickness of.080 aluminum construction. 2. The sign face shall have a white reflective background with a red legend. Use the standard 3M Scotchlite sign face number R7-32 or equivalent, with red screen printed lettering as shown above. 3. Font style is Handel Gothic capital font. 4. Decorative trim plate shall be 14 x 20 inches with a thickness of.080 aluminum, color owner s choice. Chapter 2-10
12 DESIGNER FIRE LANE SIGN POST & INSTALLATION NOTES: 1. The sign plate shall be 12 x 18 inches with a thickness of.080 aluminum construction. 2. The sign face shall have a white reflective background with red screen printed legend. 3. Letters using a Handel Gothic capital font. 4. Decorative trim plate shall be 14x20 inches with a thickness of.080 aluminum, color owner s choice. 5. Ten-foot long painted 2x2 inch square or round post shall be installed 12 to 18 inches from back of curb or back of sidewalk. 6. The sign shall be located seven (7) feet above finished grade to bottom of the sign. 7. Minimum of ¼ bolt with flat washers and nuts that bolt through post. 8. Signs MUST FACE ONCOMING TRAFFIC. Chapter 2-11
13 ALTERNATIVE FIRE LANE MARKING SYSTEM LETTERS 24 HT. 3 STROKE USING HANDEL GOTHIC CAPITAL LETTERS Chapter 2-12
14 ALTERNATIVE FIRE LANE MARKING SYSTEM NOTES: 1. Letters 24-inch height, three (3) inch stroke, using Handel Gothic capital letters. 2. Install performed pavement markings type I (AZ, DOT sect ). Chapter 2-13
15 REMOVABLE FIRE LANE SIGN Chapter 2-14
16 FOLDING FIRE LANE SIGN Chapter 2-15
17 ALTERNATIVE SURFACE FIRE LANE MARKING SOFT SURFACE Chapter 2-16
18 STANDARD AERIAL FIRE APPARATUS ACCESS ROAD FOR BUILDINGS GREATER THAN 30 IN HEIGHT MINIMUM 15 BUILDING GREATER THAN 30 IN HEIGHT MINIMUM 41 MINIMUM FIRE LANE MINIMUM FIRE LANE MINIMUM 26 MAXIMUM 30 PROXIMITY TO BUILDING PER D International Fire Code Appendix D105.3: The side of the building on which the aerial apparatus access road is positioned shall be approved by the Fire Code Official. Chapter 2-17
19 REFLECTIVE BLUE MARKER INSTALLATION DETAIL MATERIALS Acrylic plastic reflector filled with a tightly adherent potting compound. Reflective area is 3.25 square inches per reflective face. PRISMATIC REFLECTOR (One side only for one-way traffic) Plan View Elevation View NOTES: 1. Blue reflectors are required to help identify the location of fire hydrants and fire department connections (FDC) in the dark. 2. Blue reflectors shall be placed one (1) foot off the center line of the street or lane toward the hydrant or FDC. 3. One (1) marker is required to identify a fire hydrant. 4. Two (2) markers are required approximately three (3) inches apart to identify an FDC. Chapter 2-18
CHECKLIST PRELIMINARY SUBDIVISION AND PRELIMINARY SITE PLAN
N/A Waiver (1) Four (4) copies of application form. (2) Fifteen (15) copies of plan (3) Subdivision/site plan application fee & professional review escrow deposit (4) Variance application fee & professional
Plan Preparation Checklist
Appendix D Plan Preparation Checklist It is the responsibility of the Designer to complete and submit this checklist along with all required drawings for OUC (EFP) Review. All drawings submitted for OUC
CITY OF DES MOINES, IA PERMIT AND DEVELOPMENT CENTER 602 Robert D Ray Drive Des Moines, IA Phone:
CITY OF DES MOINES, IA PERMIT AND DEVELOPMENT CENTER 602 Robert D Ray Drive Des Moines, IA 50311 Phone: 515-283-4200 Minor Site Plan list This checklist should be used as a guide in the preparation of
SECTION 3 IMPROVEMENT PLAN REQUIREMENTS
SECTION 3 IMPROVEMENT PLAN REQUIREMENTS CONTENTS Page 3-1 Digital Submittals 3-2 3-2 Paper Size and Scale 3-2 3-3 Drafting Standard 3-2 3-4 Title Sheet 3-2 3-5 Title Block 3-3 3-6 Drainage, Sewer, Water,
MULTIPLE-FAMILY DESIGN REVIEW SUBMITTAL CHECKLIST
MULTIPLE-FAMILY DESIGN REVIEW SUBMITTAL CHECKLIST This application lists the content and format of the submittal requirements to initiate the Design Review process. An incomplete application will not be
PLANNING Development Services Department
PLANNING Development Services Department Date Stamp APPLICATION SUBMITTAL CHECKLIST for Design Review Case Number: I acknowledge that the City of Glendale requires the following items be submitted before
Minor Site Plan Review Process
Minor Site Plan Review Process Pre-Application Conference Community Meeting (optional) Submit Application Determination of Completeness Staff Report (optional) Technical Review Committee Decision Notice
Standard Signs Manual
Standard Signs Manual NEW, CHANGED, OR DELETED 1/2017 STANDARD SIGN DETAILS Title Page Number Fractions... 101 Straight Arrows... 102 Double Head Arrows... 102A Double Head Arrows - 90... 102B Advance
Plan Submittal and Review Checklist
Improving quality of life today creating a better tomorrow Plan Submittal and Review Checklist Version 1.2 September 4, 2017 Contents Overview... 2 Plan Submittal Checklist... 2 Plan Review Checklist -
Site Plan Review Application. Interest in the Property (e.g. fee simple, land option, etc.)
1. Identification CITY OF FENTON 301 South Leroy Street Fenton, Michigan 48430-2196 (810) 629-2261 FAX (810) 629-2004 Site Plan Review Application Project Name Applicant Name Address City/State/Zip Phone
TOWN OF OAKVILLE FIRE ROUTE APPLICATION PACKAGE
TOWN OF OAKVILLE FIRE ROUTE APPLICATION PACKAGE This application package contains: Page1. 2. 3. 4. 5. 6. 7. Application Process Description Minimum Fire Route Design Requirements Drawing Requirements Sample
DOWNTOWN DEVELOPMENT REVIEW BOARD APPLICATION
This application, including the Conceptual Review Presentation, must be completed and submitted to the Downtown Development Review Board (DDRB) Staff twenty (20) business days prior to the upcoming DDRB
Existing and proposed contours at 1-foot intervals. The fill and/or excavation quantities in cubic yards.
PLAN REQUIREMENTS The plans for street design shall conform to the requirements of Sections 3 and 4. The following requirements shall also be shown on the plans where applicable. Road and Storm Plans:
CITY OF MUSKEGO DRAFTING STANDARDS
CITY OF MUSKEGO DRAFTING STANDARDS GENERAL - These standards apply to all plans. 1. Plans must be prepared on sheets measuring 36 inch across and 22 inch to 24 inch high unless otherwise specified under
Estimated Cost of Project Contractor License No. Contractor Qualifier No.
Building, Safety and Zoning Department COMMERCIAL Application for Building Permit Owners and/or Contractors: Please fill out all the information listed below and submit those documents needed for your
SITE PLAN, SUBDIVISION & EXTERIOR DESIGN REVIEW PROCESS
INCORPORATED VILLAGE OF ROCKVILLE CENTRE BUILDING DEPARTMENT SITE PLAN, SUBDIVISION & EXTERIOR DESIGN REVIEW PROCESS Presubmission - Prior to a formal submission, the applicant should meet in person with
Chapter 14. Signage Guidelines 14.2 GENERAL DESIGN OBJECTIVES 14.1 INTRODUCTION AND PURPOSE 14.3 GENERAL SIGN DESIGN GUIDELINES
Chapter 14 Signage Guidelines 14.1 INTRODUCTION AND PURPOSE This Chapter addresses signage for all development types within the City of Santa Ana. The signage design guidelines are intended to ensure quality
SITE PLAN APPLICATION
SITE PLAN APPLICATION SECTION 1. APPLICANT/OWNER INFORMATION Please Print or Type Applicant/Developer: City: State: Zip: Telephone: Fax: E-mail: Applicant s Status: (Check One) Owner Tenant Prospective
A. Submit manufacturer's technical data and installation for each type of sign required.
SECTION 10425 PART ONE GENERAL 1.1 SECTION INCLUDES A. Interior Building Signage. B. Handicapped parking signs. C. Permanent Project Sign. 1.2 DESCRIPTION A. Signage shall consist of room number and room
DEVELOPMENT PLAN CHECKLIST
Project Identification Information: DEVELOPMENT PLAN CHECKLIST 1.0 GENERAL 1.1 Additional information as required by specific Land Use 1.2 All sheets to include sheet number ( of ) 1.3 Seal and signature
DEVELOPMENT SERVICES SITE PLAN SUBMITTAL 2.2.3
DEVELOPMENT SERVICES SITE PLAN SUBMITTAL 2.2.3 Unified Development Code (UDC) Article 2, Applications, Procedures and Criteria provides the steps for applying the Unified Development Code standards to
Anne Arundel County Dept. of Inspections and Permits Water Sewer Plan Checklist
Project Name Project Number Engineer Plans are to be designed based on the standards set forth in the Anne Arundel County Design Manual Standards and Specifications, and all other manuals as stipulated
Addendum for 2018-COA-486 and 2018-COA-487 for the LeRoux and Cho 77 Projecting signs
Addendum for 2018-COA-486 and 2018-COA-487 for the LeRoux and Cho 77 Projecting signs Included documents: Principle 7 of the Design Guidelines for Lower Downtown Historic District (June 19, 2007) Sugar
Temporary Sign Permit
36725 Division Road, P.O. Box 457, Richmond, MI 48062 Building and Planning Department 586-727-7571 ext. 228 586-727-2489 Fax Temporary Sign Permit Application and Regulations Page 1 Updated: 15OCT15 Temporary
B.2 MAJOR SUBDIVISION PRELIMINARY PLAN CHECKLIST
B.2 MAJOR SUBDIVISION PRELIMINARY PLAN CHECKLIST YES* GENERAL SUBMISSION ITEMS Does the submission include: 1. Thirteen (13) copies of completed Application Form? 2. Thirteen (13) copies of the Preliminary
Excavating, Backfilling, and Compaction for Utilities Piping (Plumbing).
SECTION 15047 - IDENTIFICATION PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Identification including necessary accessories indicated on Construction Documents and specified in this section or as required
City Development Department 9500 Civic Center Drive Thornton, Colorado FAX
City Hall City Development Department 9500 Civic Center Drive 303-538-7295 Thornton, Colorado 80229-4326 FAX 303-538-7373 www.cityofthornton.net Zach Lauterbach Evergreen Devco, Incorporated 2390 East
CHAPTER 3 INFORMATION REQUIRED FOR PUBLIC IMPROVEMENT CONSTRUCTION PLANS TABLE OF CONTENTS
CHAPTER 3 INFORMATION REQUIRED FOR PUBLIC IMPROVEMENT CONSTRUCTION PLANS TABLE OF CONTENTS Section Title Page 3.1 General... 3-1 3.1.1 Plan Set...3-1 A. Loveland (City Limits Only)...3-1 3.1.2 Final Mylars...3-1
WILTON MANORS, Island City 2020 WILTON DRIVE, WILTON MANORS, FLORIDA 33305
WILTON MANORS, Island City 2020 WILTON DRIVE, WILTON MANORS, FLORIDA 33305 COMMUNITY DEVELOPMENT SERVICES (954) 390-2180 FAX: (954) 567-6069 This package includes: General Submittal Procedures Submittal
ARCHITECTURAL REVIEW COMMITTEE TOWN APARTMENT CONSTRUCTION SUBMITTAL FORM AND APPLICATION
For Office Use Only Date Received: Approved: ARC Non-Refundable Fees ARC Refundable Deposit Pd: For Office Use Only Plat Name: Lot # Street Address: New Construction Alteration Preliminary Final ARCHITECTURAL
ARCHITECTURAL REVIEW COMMITTEE HOMESITE CONSTRUCTION SUBMITTAL FORM AND APPLICATION
For Office Use Only Date Received: Approved: ARC Non-Refundable Fees: ARC Refundable Deposit Pd: For Office Use Only Plat Name: Lot # Street Address: New Construction Alteration Preliminary Final ARCHITECTURAL
Last Name: First Name: M.I:
ARCHITECTURE DESIGN REVIEW BOARD APPLICATION OFFICE USE ONLY APPLICATION # Permit # Fee Collected $ 1. Filing Status Initial Submission Amendment Withdrawal 2. Cost of Construction (Industry Standards)
F-4 FURNITURE. Contents
Contents F-4-1 Public Art Pole F-4-2 Banner Pole F-4-3 Typical Banner Installation F-4-4a Banner/Flower Basket Pole F-4-4b Banner/Flower Basket Pole F-4-5 Flower Basket Brackets F-4-6 TTC Station Sign
WALKS AND SIDEWALKS REQUIREMENTS:
DOUBLE PARKING STALLS DIAGONAL PARKING STALLS EXTERIOR ROUTES OF TRAVEL: From accessible parking spaces, provide most practical direct accessible route of travel to all building entrances and exteriorground
UTILITY AND STREET CONSTRUCTION PLAN REQUIREMENTS SECTION 1
UTILITY AND STREET CONSTRUCTION PLAN REQUIREMENTS SECTION 1 ENGINEERING STANDARDS FOR UTILITY AND STREET CONSTRUCTION PLANS MARCH 2014 CONSTRUCTION PLAN SHEET FORMAT REQUIREMENTS REPRODUCIBLE MYLAR 1.
DECK PERMIT APPLICATION PACKET
Building Division 865 SE Barrington Dr Oak Harbor, WA 98277 Ph 360.279.4510 Fax 360.279.4519 DECK PERMIT APPLICATION PACKET SUBMITTAL FORMS INDEX Basic Deck Submittal Checklist Residential Deck Submittal
Uniform Sign Plan (USP) MacGregor Village 86-USP-003
Uniform Sign Plan (USP) MacGregor Village 86-USP-003 These guidelines are published for informational purposes. They describe the characteristics of signs, not structures on which signs are placed. A sign
DEPARTMENT OF COMMUNITY DEVELOPMENT SITE PLAN INFORMATION
DEPARTMENT OF COMMUNITY DEVELOPMENT SITE PLAN INFORMATION 220 Clay Street Cedar Falls, Iowa 50613 General Information: Applications for developing a commercial, multi-family, or residential (in an overlay
CITY OF MERCER ISLAND DEVELOPMENT SERVICES GROUP 9611 SE 36 th Street, Mercer Island, WA (206)
CITY OF MERCER ISLAND DEVELOPMENT SERVICES GROUP 9611 SE 36 th Street, Mercer Island, WA 98040 (206) 275-7605 SUBMITTAL REQUIREMENTS FOR DESIGN COMMISSION APPROVAL & SIGNAGE APPROVAL PURPOSE: Design Commission
Desk/Wall-Mount Rack
Desk/Wall-Mount Rack Patent(s) Pending Installation Instructions Post P/N: 119-1752 119-1781 119-1782 119-4014 Frame P/N: 119-1591 119-1754 119-1755 Kit Contents (2) Frames (4) Posts Assembly Hardware
INCOMPLETE APPLICATION WILL NOT BE ACCEPTED COMPLETE ALL INFORMATION BELOW. Construction Value: $
CITY OF PORT ORCHARD Permit Center Office located at 720 Prospect Street Mailing address: 216 Prospect Street Port Orchard, WA 98366 (360) 874-5533 permitcenter@cityofportorchard.us COMMERCIAL or MULTI-FAMILY
TOWN OF AMHERST PLANNING DEPARTMENT MINOR SITE PLAN AND MINOR ADJUSTMENT REVIEW AND APPROVAL PROCEDURE
TOWN OF AMHERST PLANNING DEPARTMENT MINOR SITE PLAN AND MINOR ADJUSTMENT REVIEW AND APPROVAL PROCEDURE This application package includes the following: Application Procedures Application Form & Checklist
SECTION STEEL LIGHTING STANDARDS. 1. Electrical conduit and fittings; Section
02760-1 of 5 SECTION 02760 STEEL LIGHTING STANDARDS 02760.01 GENERAL A. Description Steel lighting standards shall include, but not necessarily be limited to, furnishing and installing steel lighting poles,
SECTION IDENTIFYING DEVICES
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 10441 IDENTIFYING DEVICES A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division-1 specification section,
Washington County Road Engineering Plan Submittal/Review Checklist
Washington County Road Engineering Plan Submittal/Review Checklist Washington County Land Use Case File Number: Parcel(s): Developer/Owner Name(s): Developer/Owner E-mail(s): The following elements should
Required Documents for Commercial Permits Permit Types 1. New Structure 2. Addition 3. Remodel 4. Tenant Finish 5. Change of Tenant/Use 6.
Required Documents for Commercial Permits Permit Types 1. New Structure 2. Addition 3. Remodel 4. Tenant Finish 5. Change of Tenant/Use 6. Temporary Use 7. Decks over 30 inches 8. Re-Roof 9. Plumbing 10.
STATE UNIVERSITY CONSTRUCTION FUND
DIRECTIVE 1C-12 Issue date: August 2012 1. General SURVEY, MAPPING AND UTILITY LOCATING This Directive has been developed as a general guide for the survey and mapping effort required for Fund projects.
PUBLICATION 213. Think Safety First
PUBLICATION 213 (67 PA CODE, CHAPTER 212) Think Safety First Pub 213 (02-08) Appendix Appendix A - Temporary/Portable
6 1/2 x 6 1/2 Wood Grain Flat Top Pergola
/ x / Wood Grain Flat Top Pergola A S S E M B LY G U I D E Models: Lakewood OPTIONAL ACCESSORY Bolt Down Bracket Kit V.-09 Ta b l e o f Co n t e n t s The PAGE Introduction & Overview.......................................................
SECTION SITE SURVEYS
SECTION 02 21 13 SITE SURVEYS SPEC WRITER NOTE: 1. Delete text between // // not applicable to project. Edit remaining text to suit project. 2. Use this section to specify survey required before design
PLANNING AND DEVELOPMENT
OVERVIEW Effective January 1, 1992 all applications for multi-family residential and all non-residential building permits require site plan approval before permit issuance. All new developments and existing
Subdivision Application Checklist
City of Portsmouth, New Hampshire Subdivision Application Checklist This subdivision application checklist is a tool designed to assist the applicant in the planning process and for preparing the application
Porter County Plan Commission
Plan Type: Development Plan Administrative DRC PC Primary Plan Administrative DRC PC Secondary Plat/Replat Administrative DRC PC PUD Conceptual Detailed Final Project Information Project Name: Developer
TYPICAL PATIO COVERS. OWNER: ADDRESS: PHONE:
City of Aliso Viejo Building Division 12 Journey, Suite 100 Aliso Viejo, CA 92656 (949)425-2540 Fax (949)425-3899 www.cityofalisoviejo.com TYPICAL PATIO COVERS 111 I. GENERAL Patio covers are one-story,
BRASELTON WATER AND WASTEWATER DEPARTMENT CONSTRUCTION PLAN REVIEW CHECKLIST May 2006
Project Name: BRASELTON WATER AND WASTEWATER DEPARTMENT CONSTRUCTION PLAN REVIEW CHECKLIST May 2006 Phase: Unit: # Lots: Development Type (residential, commercial, industrial, etc.) Braselton Project No.
OVER-HEIGHT FENCE/RETAINING WALL CERTIFICATION APPLICATION
OVER-HEIGHT FENCE/RETAINING WALL CERTIFICATION APPLICATION Application information below to be completed by Applicant/Agent//Owner APN PROPERTY ADDRESS PROPERTY LOCATION (if no address) APPLICANT S NAME
MDOTProjectwise\Documents\Reference Documents\Traffic Reference\Statewide Special Details\Develop
500 460 MDOTProjectwise\Documents\Reference Documents\Traffic Reference\Statewide Special Details\Develop Check if Applicable TRAFFIC SIGNAL SPECIAL DETAILS INDEX/CHECKLIST *One completed checklist required
City of Beaumont. Public Works Engineering. Street Improvement Plan Checklist REV 4/18/16
City of Beaumont Public Works Engineering Project Name: TR: Project No.: Date: Street Improvement Plan Checklist Chk A. All Sheets 1. 24" x 36" 2. Signed by the engineer-of-work 3. Marked with the contact
Site Plan/Building Permit Review
Part 6 Site Plan/Building Permit Review 1.6.01 When Site Plan Review Applies 1.6.02 Optional Pre- Application Site Plan/Building Permit Review (hereafter referred to as Site Plan Review) shall be required
CITY OF WHITE PLAINS STANDARD DESIGN CRITERIA AND SPECIFICATIONS FOR SMALL WIRELESS FACILITIES
CITY OF WHITE PLAINS STANDARD DESIGN CRITERIA AND SPECIFICATIONS FOR SMALL WIRELESS FACILITIES Small 1.1 Definitions: Antenna - Communications equipment that transmits or receives electromagnetic radio
CITY OF TUMWATER 555 ISRAEL RD. SW, TUMWATER, WA (360)
CITY OF TUMWATER 555 ISRAEL RD. SW, TUMWATER, WA 98501 (360) 754-4180 Email: cdd@ci.tumwater.wa.us WATER-SEWER-STREET-STORM (IN CITY) Submittal Checklist TUM - RCVD BY DATE STAMP APPLICANT INFORMATION
CITY OF APACHE JUNCTION DEVELOPMENT SERVICES CIVIL ENGINEERING PLAN REVIEW CHECKLIST PROJECT: LOCATION:
CITY OF APACHE JUNCTION DEVELOPMENT SERVICES CIVIL ENGINEERING PLAN REVIEW CHECKLIST PROJECT: LOCATION: LOG NO.: LEGEND REVIEW REVIEWED BY DATE / - Requirement satisfied 1 O Requirement not satisfied 2?
CSP PSYCHIATRIC SERVICES UNIT SECTION IDENTIFICATION FOR HVAC PIPING AND EQUIPMENT
SECTION 23 05 53 IDENTIFICATION FOR HVAC PIPING AND EQUIPMENT PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Pipe Markers. 2. Valve Tags. 3. Equipment Nameplates. 4. Underground Marking Tape. 5. Duct
Chapter 17 - Porch Trim
Chapter 17 - Porch Trim Contents Chapter 17 - Porch Trim... 17-1 Timing & Prerequisites... 17-2 Trim on Porch Beams (Volunteer)... 17-4 Smart Trim on the Bottom of the Beam... 17-4 Smart Trim on the Inside
DRAFT V. SITE ELEMENTS SIGNS
1. SIGNS Intent Signs are an important streetscape design element that affect not only the visual character of the Historic District but also the vitality of its businesses. Signage provides business identification,
Rezoning Application for Planning Commission
36725 Division Road, P.O. Box 457, Richmond, MI 48062 Building and Planning Department 586-727-7571 ext. 128 586-727-2489 Fax Rezoning Application for Planning Commission For a complete list of application
Installation Instructions for Vista Air Vertically Folding Walls
Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.
The School District of Palm Beach County Project Name SDPBC Project No. SECTION ( ) SIGNAGE PART 1 GENERAL 1.1 RELATED DOCUMENTS
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 10441 (10 14 00) SIGNAGE A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division-1 specification section,
PLANNING DEPARTMENT SUBMITTAL REQUIREMENTS FOR CONDITIONAL USE PERMITS CLASS 4 DEVELOPMENT REVIEW PROCESS. A. Written Material
PLANNING DEPARTMENT 970.668.4200 0037 Peak One Dr. PO Box 5660 www.summitcountyco.gov Frisco, CO 80443 SUBMITTAL REQUIREMENTS FOR CONDITIONAL USE PERMITS CLASS 4 DEVELOPMENT REVIEW PROCESS Per the provisions
DOCUMENT ADDENDUM NO. 4. Issued to all Bidders: Date: October 14, Contract Name: Electrical Installation. Contract Number: C8410
DOCUMENT 009104 - ADDENDUM NO. 4 Issued to all Bidders: Date: October 14, 2015 Contract Name: Electrical Installation Contract Number: C8410 This addendum forms a part of the Bid described above. The original
When is a Building Permit Required? Deck Details: What Must be Submitted with a Building Permit Application?
P.O. Box 1190, Fort Collins, Colorado 80522-1190, Planning (970) 498-7683, Building (970) 498-7700, Larimer.org When is a Building Permit Required? A permit is required if ANY of the following is true:
STATE OF OHIO DEPARTMENT OF TRANSPORTATION. SUPPLEMENTAL SPECIFICATION 817 SPRAY THERMOPLASTIC PAVEMENT MARKING April 15, 2011
817.01 Description 817.02 Materials 817.03 Equipment 817.04 Surface Preparation 817.05 Application 817.06 Basis of Payment STATE OF OHIO DEPARTMENT OF TRANSPORTATION SUPPLEMENTAL SPECIFICATION 817 SPRAY
Town of Mount Pleasant PRELIMINARY Design Review Submittal Check List June 1, 2014
Town of Mount Pleasant PRELIMINARY Design Review Submittal Check List June 1, 2014 This form is to be completed by either applicant or their representative and submitted with Preliminary Review plans.
Article 4.0 Measurements and Exceptions
This Article identifies and explains some of the more common forms of measurement used throughout this Ordinance. It also specifies exceptions to certain requirements of this Ordinance. Sec. 4.1 Measurements
City of Colleyville Community Development Department. Site/Landscape Plan Application Packet
City of Colleyville Community Development Department Site/Landscape Plan Application Packet 1 Development Application Fees City of Colleyville 100 Main Street Colleyville TX 76034 817.503.1050 Zoning Zoning
Planning Permit Application LAND USE PRELIMINARY APPLICATION (LUP)
Planning Permit Application LAND USE PRELIMINARY APPLICATION (LUP) 415 W 6 th ST ~ Vancouver, WA 98660 PO Box 1995 ~ Vancouver, WA 98668 Phone (360) 487-7800 www.cityofvancouver.us Type Of Work Type I
CITY OF PINE CITY SMALL WIRELESS FACILITY DESIGN GUIDELINES
CITY OF PINE CITY SMALL WIRELESS FACILITY DESIGN GUIDELINES I. PURPOSE AND COMPLIANCE In implementing City Code, Chapter 8, Section 815, the City Council of the City of Pine City (the City ) finds that
ONE AND TWO FAMILY DWELLINGS Uncovered Decks July, 2007
ONE AND TWO FAMILY DWELLINGS Uncovered Decks July, 2007 In the City of Lee s Summit, the construction of uncovered decks with a floor surface more than 30 inches above the adjacent grade level requires
ASSEMBLY INSTRUCTIONS FOR SERVICE BODY A MOUNT RACKS
ASSEMBLY INSTRUCTIONS FOR SERVICE BODY A MOUNT RACKS T12 Service Body A shown with optional middle crossbar Package Contents: HARDWARE KIT PARTS (8) 3/8-16 x 3 CARRAIGE BOLTS (1) RAIL DRIVER S SIDE ASSEMBLIES
LOWNDES COUNTY ENGINEERING PLAN REVIEW CHECKLIST. Design Professional: Phone: Developer: Phone: 2 nd Submittal (No Fee)
MEMORANDUM MICHAEL B. FLETCHER, P.E. COUNTY ENGINEER 327 N. Ashley Street Valdosta, GA 31601 Telephone: (229) 671-2424 Fax: (229) 245-5299 mfletcher@lowndescounty.com LOWNDES COUNTY ENGINEERING PLAN REVIEW
SECTION EDITION - REVISION 2. Large Guide
SECTION 4 0 EDITION - REVISION Large Guide March 017 (This page left intentionally blank) Guide Sign Design Guidelines Design Guidelines There are general guidelines to follow in the design of highway
CITY OF FOLSOM SUBMITTAL REQUIREMENTS FOR INSTALLATION OF A COMMERCIAL REFUSE OR CARDBOARD COMPACTOR FOR AN EXISTING BUILDING
CITY OF FOLSOM SUBMITTAL REQUIREMENTS FOR INSTALLATION OF A COMMERCIAL REFUSE OR CARDBOARD COMPACTOR FOR AN EXISTING BUILDING Before installation of a commercial refuse or cardboard compactor in or near
PATHWAY 3G MODULAR ACCESS SYSTEM
PATHWAY 3G MODULAR ACCESS SYSTEM TECHNICAL & ARCHITECTURAL SPECIFICATIONS Manufactured in the USA Homecare Products, Inc. All rights reserved. All text and images contained in this document are proprietary
WATER & SEWER CONSTRUCTION SITE PLAN DESIGN SUMMARY COMMERCIAL & RESIDENTIAL
WATER & SEWER CONSTRUCTION SITE PLAN DESIGN SUMMARY COMMERCIAL & RESIDENTIAL This summary is not all inclusive of the requirements set forth by the York County Planning & Development Services, York County
INSTALLATION, ASSEMBLY & OPERATIONAL MANUAL
INSTALLATION, ASSEMBLY & OPERATIONAL MANUAL Dog Park Equipment Hill Climb, Balance Beam, Bridge Climb, Mini Hill Climb, Jump Hurdles, Tunnel House, Training Platform, Jump Balance Beam Safe Zone When installing
I. REQUEST: The undersigned petition the Village of Matteson, Illinois to approve the application(s) submitted.
SITE PLAN BUILDING ELEVATION LANDSCAPE PLAN SIGNAGE PLAN APPLICATION FOR THE VILLAGE OF MATTESON I. REQUEST: The undersigned petition the Village of Matteson, Illinois to approve the application(s) submitted.
CONCEPT REVIEW GUIDELINES
Department of Planning & Community Development @ Jefferson Station 1526 E. Forrest Avenue Suite 100 East Point, GA 30344 404.270.7212 (Phone) 404.765.2784 (Fax) www.eastpointcity.org CONCEPT REVIEW GUIDELINES
DIVISION PAVEMENT MARKINGS AND MARKERS
DIVISION 61 66 PAVEMENT MARKINGS AND MARKERS 66.01 SCOPE: The purpose of these specifications is to describe the minimum requirements of the City of Chesapeake for pavement markings and shall be in addition
APPENDIX FENCE GENERAL NOTES
APPENDIX FENCE GENERAL NOTES 1. Fabric: 9 gage, 2" mesh, knuckle top and bottom, placed on the outside of posts, single fabric width for the entire height. 2. All fencing to be standard galvanized finish.
APPENDIX 1: CONSTRUCTION PLAN CHECKLIST
APPENDIX 1: CONSTRUCTION PLAN CHECKLIST October 2017 APPENDIX A APPENDIX 1: CONSTRUCTION PLAN CHECKLIST ALL PLANS Plans on 24-inch by 36-inch paper (Originals shall be transmitted on a CD as an electronic
BUILDING & SAFETY DIVISION 110 E. LA HABRA BLVD. LA HABRA, CA Rev. 06/17
STANDARD OPEN PATIO COVER (PLEASE NOTE: These are general guidelines, not to be used in lieu of actual code requirements for final design. Your final design will be subject to plan review.) BUILDING &
SECTION SIGNAGE
SECTION 10 14 00 SIGNAGE PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division-1 specification section, apply
Procedure for Testing Direct Tension Indicators (DTI) Assemblies
Procedure for Testing Direct Tension Indicators (DTI) Assemblies 1. Scope: This test is to ensure that the bolt will be at or above the specified minimum bolt tension after installation when the direct
SECTION TRAFFIC SIGNAGE
SECTION 10 14 53 TRAFFIC SIGNAGE PART 1 - GENERAL 1.01 SECTION INCLUDES A. Furnishing and installing roadside traffic signage. B. Providing additional traffic signs as required in Sections 01 55 28 Controlling
PROJECT ENTITLEMENT APPLICATION
GENERAL REQUIREMENTS (Print or Type) Name of Proposed Project: Location of Project: Legal Description of Project (Assessor s Parcel/Allotment No., Township/Range/Section): Staff Use Only CASE NO.: RELATED
CITY OF LONG BEACH Department of Development Services BUILDING AND SAFETY BUREAU SIGNS SUPPLEMENTAL ACCESSIBILITY PLAN REVIEW CHECKLIST NO.
INFORMATION INSTRUCTIONS CITY OF LONG BEACH Department of Development Services BUILDING AND SAFETY BUREAU SIGNS SUPPLEMENTAL ACCESSIBILITY PLAN REVIEW CHECKLIST NO. 2 PROJECT NO.: EXPIRATION DATE: STATUS:
LARAMIE COUNTY PLANNING & DEVELOPMENT OFFICE 3966 Archer Pkwy Cheyenne, WY Phone (307) Fax (307)
3966 Archer Pkwy Cheyenne, WY 82009 planning@laramiecounty.com Phone (307) 633-4303 Fax (307) 633-4616 SITE PLAN REVIEW PROCESS 1. Pre-Application Meeting: The applicant shall meet with a Laramie County
INSTALLATION INSTRUCTIONS 3"/4 BENT END SIDEBARS FORD F-150 SUPERCREW PART # DZ /DZ
INSTALLATION INSTRUCTIONS 09-12 FORD F-150 SUPERCREW PART # DZ 372697/DZ 372699 PARTS LIST: 1 Driver/Left Sidebar 4 1/2 Lock Washers 1 Sidebar 4 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Mounting
ASSEMBLY INSTRUCTIONS FOR HAULER II SERVICE BODY A RACK
ASSEMBLY INSTRUCTIONS FOR HAULER II SERVICE BODY A RACK T12USBA-1 shown above Package Contents: HARDWARE KIT PARTS (4) 3/8-16 x 3 CARRAIGE BOLTS (1) RAIL DRIVER S SIDE ASSEMBLY (20) 3/8-16 x 2 CARRAIGE
Series 1600 WeatherGuard Dock Enclosure
Fairborn USA Inc. 205 Broadview Street Upper Sandusky, OH 43351 1-800-262-1188 Fax 1-419-294-4980 Series 1600 WeatherGuard Dock Enclosure All Models! WARNING Do not install this product unless you read