DGS Phase 1 COORDINATION DRAWINGS

Transcription

1 SECTION COORDINATION DRAWINGS PART 1 - GENERAL 1.1 STIPULATIONS A. The specifications sections " General Conditions of the Construction Contract ", "Special Conditions", and "Division 1 - General Requirements" form a part of this Section by this reference thereto, and shall have the same force and effect as if printed herewith in full. B. This specification section supersedes the requirements in the "General Conditions of the Construction Contract "; where inconsistencies and/or conflicts occur, the requirements of this section shall prevail. 1.2 SUMMARY A. Where space for installation of essential building services is limited, and to avoid conflicts among the building trades, it is necessary for the Prime Contractors to coordinate the use of shared space, and prepare Coordination Drawings, before commencing the Work. All Prime Contractors and their associated subcontractors, during the coordination process, shall harmoniously plan and/or adjust the location of items as necessary, to avoid such conflicts and to ensure future access to critical items of equipment. All Prime Contractors shall also coordinate the installation sequence as necessary. B. Coordination of the Work, and production of Coordination Drawings, are contractual obligations of all Prime Contractors. The Department will not compensate any Prime Contractor for conflicts arising during installation, should they be the result of improper coordination between Prime Contractors. Nor will the Department extend the Contract duration, due to delays caused by improper coordination. Each Contractor shall be solely responsible to recover any and all construction time lost as a result of such delays. C. In the General Conditions of the Construction Contract, Article 9.5 Coordination Drawings, Section D states that the HVAC Contractor (.2) will be the Lead Contractor for the purposes of the Coordination Drawings and shall facilitate the Coordination Drawing Process between Prime Contractors. 1.3 SUBMITTALS A. Time of submission of Coordination Drawings shall be determined at the initial job conference, and shall be included as a milestone on the Construction Schedule. The HVAC Construction (.2) Contractor shall initiate this action and acquire the necessary dates from the other Prime Contractors as part of their overall scheduling responsibilities. B. All Prime Contractors shall jointly develop and submit dimensioned Coordination Drawings indicating the arrangement of General Construction, HVAC, Plumbing and Electrical work, including but not limited to: all ducts, air-handling equipment, control equipment, piping, conduits, raceways, junction boxes, fixtures, panels, and all associated equipment, which must be coordinated with the General Construction and other equipment or distribution lines. The Coordination Drawings must be signed and dated by all Prime Contractors, indicating concurrence, and transmitted to the HVAC Construction (.2) Contractor (in accordance with DGS Phase 1 COORDINATION DRAWINGS

2 the construction schedule), for who shall submit complete copy sets to the Department and to the Professional. C. The Department s receipt of Coordination Drawings does not in any way constitute approval, or relieve the Prime Contractors of the responsibility to accurately coordinate and install their work. D. The HVAC Construction (.2) Contractor shall submit completed, signed, and dated Coordination Drawings as follows: 1. The Department two (2) prints of each Coordination Drawing. 2. The Professional one (1) reproducible mylar of each Coordination Drawing. 3. The Using Agency - one (1) print of each Coordination Drawing, if requested. 4. Prime Contractors - one (1) reproducible mylar of each Coordination Drawing. E. Note: If determined necessary, Coordination Drawings may be formulated and submitted in partial submittals to facilitate the construction schedule and sequence of work within the Project. This must be jointly discussed and agreed to by all Prime Contractors at the initial job conference, and a priority of sequence must be established that has the concurrence of all parties (including the Department). 1.4 COORDINATION OF WORK A. Each Prime Contractor shall coordinate its construction operations with those of other Prime Contractors and entities to ensure efficient and orderly installation for each part of the Work. Each Prime Contractor shall coordinate its operations with other operations, included in different Sections that depend on each other for proper installations, connection, and operation. All Prime Contractors shall: 1. Schedule construction operations in sequence required to obtain the best results where installation of one part of the Work depends on installation of other components, before or after its own installation. 2. Coordinate installation of all components with other Prime Contractors to ensure adequate accessibility/clearance for required maintenance and service. 3. Make provisions to accommodate items scheduled for later installation. B. Each Prime Contractor shall clearly show, and coordinate with the other Prime Contractors, the following: 1. Arrange for pipe spaces, chases, slots, sleeves, and openings with general construction work, and arrange in building structure during progress of the Work, to allow for and facilitate distribution line and equipment installation. 2. Coordinate installation of required supporting devices for ductwork, piping, and conduit, as well as sleeves, and other structural components, as they are constructed. 3. Coordinate requirements for access panels and doors for HVAC, Plumbing and Electrical items requiring access where concealed behind finished surfaces. 4. Coordinate electrical connections to equipment provided by all Contractors. 5. Sequence, coordinate, and integrate installing materials and equipment for efficient flow of the Work. Coordinate installing large items of equipment requiring positioning before closing in the building. DGS Phase 1 COORDINATION DRAWINGS

3 1.5 COORDINATION DRAWINGS A. Format: All Coordination Drawings shall include X, Y & Z coordinates for all distribution and equipment, which will allow a three-dimensional coordination plan to be created. 1. Indicate ducts, pipes and conduits of dimensions greater than 6 by double lines. 2. Circle and clearly note all deviations from the Contract Documents, with reason for deviation stated. 3. Use scale not less than 1/8 = 1-0. Detail complex areas at larger scale. B. Coordination Procedure: 1. The HVAC Construction (.2) Contractor is responsible for acquiring from all the other Prime Contractors and assembling scaled coordination drawings indicating all new and existing architectural finishes, as well as the locations of all ductwork, piping, conduit, system devices, associated equipment, etc. for this Project. 2. The HVAC Construction (.2) Contractor shall prepare the basic background drawings, showing the existing conditions as well as the new construction items to be installed by this Contractor. The HVAC Construction (.2) Contractor may either produce the required base drawings itself, or obtain them from the Design Professional, at a cost not to exceed 1.2 times the cost of reproduction. 3. After producing its own background drawings or obtaining background drawings from the Professional, the HVAC Construction (.2) Contractor shall put the following information on the Coordination Drawings: HVAC Contract Work, including Control Systems. The HVAC Construction (.2) Contractor shall call attention on the Coordination Drawings to particular areas of conflict, which may affect the architecture or the structure. 4. After adding its specific requirements to these reproducible background drawings, the HVAC Construction (.2) Contractor shall place his signature on each sheet and give the Coordination Drawings to the Plumbing Construction (.3) Contractor. 5. The Plumbing Construction (.3) Contractor shall put the following information on the Coordination Drawings: Plumbing Contract Work, including Sprinkler/ Fire Protection Systems (unless there is a separate Fire Protection contract). 6. After adding its specific requirements to these reproducible background drawings, the Plumbing Construction (.3) Contractor shall place his signature on each sheet and give the Coordination Drawings to the Electrical Construction (.4) Contractor. 7. The Electrical Construction (.4) Contractor shall put the following information on the Coordination Drawings: Electrical Contract Work, including fire alarm, telecommunications and security systems, major conduit runs, lighting and panel locations, and conduit embeds in floor slabs and underground. 8. After adding its specific requirements to these reproducible background drawings, the Electrical Construction (.4) Contractor shall place his signature on each sheet and give the Coordination Drawings to the General Construction (.1) Contractor. 9. The General Construction (.1) Contractor shall put the following information on the Coordination Drawings: Architectural backgrounds, structural work, ceiling systems, and any special work, such as theatre/stage/rigging work. 10. After adding its specific requirements to these reproducible background drawings, the General Construction (.1) Contractor shall place his signature on each sheet and give the Coordination Drawings to the next Prime Contractor (if there are other Prime Contractors not mentioned here), or otherwise return the Coordination Drawings to the DGS Phase 1 COORDINATION DRAWINGS

4 HVAC Construction (.2) Contractor, for Submission to the Department, the Professional and the Using Agency. 11. Discrepancies between the Prime Contractors shall be settled by the HVAC Contractor, if no design modifications are required. Where design modifications are required, affected Contractor(s) shall submit them to the Professional for review and resolution, or initiate a Request For Information (RFI). 12. The Prime Contractors, together, are solely responsible for the accuracy and completeness of all Coordination Drawings. C. Distribution: Upon receipt of all fully-coordinated and signed Coordination Drawings from the other Prime Contractors, the Lead Contractor shall make proper distribution, as hereinbefore defined in Paragraph 1.3 D. 1.6 SPECIFIC REQUIREMENTS A. General Construction/Structural Work Information Required: 1. Openings and sleeve locations required in slabs, walls, beams, and other structural elements, including required openings not indicated on the Contract Documents. 2. Slab edge locations. 3. Embed locations, as described above. Note embedded steel angles at edges of sump and sewage ejector pits, to accept basin covers. 4. Wall and chase spaces for housing HVAC, Plumbing, or Electrical items. 5. Other specific/critical conditions unique to this Project, not noted above but necessary to assure proper coordination. B. HVAC Work Information Required: 1. Sizes and bottom elevations of rectangular ductwork, including angle bracing, flanges, and support systems. 2. Sizes and centerline elevations of round ductwork, piping and conduit runs 3. Acoustical lining in ductwork. 4. Identification of ductwork pressure class. 5. Dimensions of major components, such as dampers, valves, diffusers, registers, cleanouts, coils, VAV boxes, HVAC equipment, and electrical distribution equipment. 6. Fire-rated enclosures around ductwork. 7. Access panels required. 8. Other specific/critical conditions unique to this Project, not noted above but necessary to assure proper coordination. C. Plumbing and Fire Protection Work Information Required: 1. Sizes and centerline elevations of piping runs. 2. Locations of plumbing valves, equipment, and fixtures. 3. Locations of standpipes, floor control assemblies, fire hose valves, mains, piping, branch lines, pipe drops, sprinkler heads, fire pumps/controllers, and jockey pumps. 4. Other specific/critical conditions unique to this Project, not noted above but necessary to assure proper coordination. D. Electrical Work Information Required: DGS Phase 1 COORDINATION DRAWINGS

5 1. Runs of vertical and horizontal conduit, 1 ¼ diameter and larger. 2. Light fixture locations. 3. Exit light locations. 4. Smoke detector and other fire alarm locations. 5. Panelboards, switchboards, switchgear, transformers, busways, generators and motor control center, exit signs, and emergency battery pack locations. 6. Locations of pull boxes and junction boxes, dimensioned from column centerlines. 7. Access panels required. 8. Other specific/critical conditions unique to this Project, not noted above but necessary to assure proper coordination. E. Ceiling Systems and Plenum Space Information Required: 1. For HVAC, plumbing, fire protection, fire alarm, electrical, controls, and telecommunications Work penetrating acoustical ceilings, show locations of each item (including sprinkler heads, diffusers, grilles, access doors, light fixtures, smoke detectors, exit signs, speakers, and other visible ceiling-mounted devices) relative to the acoustical ceiling grid. 2. Locate components within ceiling plenums to accommodate layout of light fixtures indicated on Drawings. Clearly indicate areas of conflict between light fixtures and other components on Coordination Drawings. 3. Other specific/critical conditions unique to this Project, not noted above but necessary to assure proper coordination. 1.7 ORGANIZATION OF DRAWINGS A. Organize Coordination Drawings into a set, as follows: Floor Plans, Wall Sections and Building Sections, Mechanical/Plumbing/Electrical Rooms, Structural Penetrations, Imbeds, Curbs, Pads, and Floor Depressions. PART 2 PRODUCTS (Not Applicable) PART 3 EXECUTION (Not Applicable) END OF SECTION DGS Phase 1 COORDINATION DRAWINGS

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23 FC-1 RTU-3 RTU-5 RTU-1 RTU-2 RTU-4 ROOF 3" CWS/R 2" 3" 2 1/2" 2" 2 1/2" 4" 6" 4" 4" 6" 4" 3" 3" 2" 1 1/2" 1" 6" HWS HWS HWS HWS HWS HWR HWR HWR HWR HWR 3/4" 3/4" 3/4" 3/4" 1" 3/4" 1" 1" 1" 3/4" 3/4" 1" 1 1/4" 1 1/4" 1 1/4" 1 1/4" 1" 1" 1" 3/4" 3/4" 3/4" 1" 1" 1" 3/4" 1" 3/4" 3/4" ROOF 6" HWS VAV 1-11 VAV 1-10 FP 1-9 FP 1-8 FP 1-7 FP 1-6 VAV 1-4 FP 1-5 VAV 1-2 FP 1-3 VAV 1-1 VAV 2-7 VAV 2-6 VAV 2-5 VAV 2-4 VAV 4-1 FP 4-2 VAV 2-3 FP 4-4 FP 4-5 VAV 4-8 VAV 4-3 FP 4-6 FP 4-11 VAV 4-1 VAV 4-7 VAV 4-9 FP 4-10 HWR HWR HWR HWR 6" UPPER LEVEL REFER TO ENLARGED MECHANICAL ROOM PLAN THIS DWG FOR CONTINUATION HWR 6" HWS 6" 3" CWS/R 6" HWR HWS HWR 3" 3/4" 3/4" 1" 1" 1 1/4" 1 1/4" 1 1/2" 1 1/2" 3" 2" 2 1/2" 2" 2 1/2" 2 1/2" 2" 2" 1 1/2" 2 1/2" 3" 1 1/2" 1 1/4" 1 1/4" 1" 3" HWS HWS HWS HWS HWS HWS HWR HWR HWR HWR HWR HWR HWR 1" 1" 3/4" 1 1/4" 1" 3" 3" 3/4" 3/4" 3/4" 3/4" 1" 3/4" 3/4" 3/4" 1" 3/4" 1" 3/4" 1" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 1" 3/4" 3/4" 1" 3/4" 3/4" 3/4" 3/4" 3/4" VAV 4-24 VAV 4-12 VAV 4-21 VAV 4-22 VAV 4-20 VAV 4-23 VAV 4-16A UH-1 VAV 4-18 FP 4-19 VAV 4-17 VAV 2-2 VAV 4-14 VAV 4-16 VAV 4-15 VAV 1-14 FP 1-15 FP 1-16 FP 1-18 FP 1-19 VAV 1-13 VAV 1-17 VAV 1-21 VAV 1-23 FP 1-20 FP 1-24 FP 1-25 FP 1-26 VAV 1-22 VAV 1-27 VAV 1-12 VAV 1-28 FP 1-29 VAV 1-30 VAV 1-31 VAV 4-25 VAV /4" 4" 1" HWR HWR HWR HWR 2 1/2" HWS/R 3" HWR 1 1/4" HWS/R DHU-1 UPPER LEVEL GROUND LEVEL 4" "HOT SIDE" PIPING. 200 GPM. SEE DETAIL 3/M4.02 FOR ADDITIONAL INFORMATION. UH-2 UH-3 "COLD SIDE" PIPING BY POOL CONTRACTOR. HX-1 SEE POOL MECHANICAL PIPING SCHEMATICS THIS DWG FOR ADDITIONAL INFORMATION. VAV /4" HWS HWR 3/4" 1" 3/4" 3/4" VAV 1-34 VAV 1-33 VAV /4" HWS/R BASE BID 1 GROUND LEVEL 3/4" 1" BASEMENT LEVEL VAV 1-32 VAV 1-33 BASE BID 2 & 3 BASEMENT LEVEL 1 PIPING FLOW DIAGRAM - BASE BIDS NO.1 SCALE: N.T.S. CAP EXT'G 2"HPS CONNECT TO EXT'G 6"LPS CAP EXT'G 1-1/2"LPS CONNECT TO EXT'G 3"PC 16x10 EXHAUST UP. INSTALL FIRE DAMPER AT FLOOR PENETRATION. SEE DWG H1.14 FOR CONTINUATION. 16x10 EXHAUST DUCT. OPEN ENDED. COVER OPENING WITH WIRE MESH. CP-1 6" LPS EXT'G 10" SAFTEY RELIEF VENT TO REMAIN 3" PC 4" CONC. HOUSEKEEPING PAD BY G.C. (TYP) 3" 3" HX-1 BY P.C. 6" HX-2 BY P.C. 1" 1" 6" BY PC SWHX-1 2" BY MC 1" 3" LPR 1" HEADER 6" 3/4" MU SWHX-2 14x10 RA HWR 6" HWS 6" 2" 20x14 4" HWR 6" 6" AS-1 HWP-1 6" HWR DN FROM 2ND LEVEL 4" HWS VAV x10 RA ET-1 HWP-2 1-1/4" 3" HWS 18x8 SA 4" CONC. HOUSEKEEPING PAD ET-2 6" HWS UP TO 2ND LEVEL 4" CONC. HOUSEKEEPING PAD GRADE EXISTING COOLING TOWER REMOVE EXISTING BELOW GRADE CONDENSER SUPPLY AND RETURN PIPING. CWS 6" 2 1/2" FC-2 CWR CTP-1 NEW 3" HPS AND 2" PD DIRECT BURY STEAM PIPING. SEE DWG. H0.11 FOR CONTINUATION. HPS 3" 2" PD EXISTING CWS/R PIPING TO REMAIN. REMOVE EXISTING SECTION OF CWS/R PIPING. STEAM PRESSURE REDUCING STATION TO REMAIN EXISTING CONDENSATE RETURN UNIT TO REMAIN. TO MECH STM COILS TO MECH HW HT EXCH. TO DOM HW HT EXCH ST COND 1" LPR 3" LPS SWHX-3 3" AS-2 CT ET-3 CHEM FEED 3" HWR HWS HWS HWP-3 4" FINNED TUBE 350 BTUH/LF HWP-4 3" 3" HWR 1 1/2" 2" "COLD SIDE" TO REC POOL SYSTEM BY POOL CONTRACTOR. HX-2 SEE POOL MECHANICAL PIPING SCHEMATICS THIS DWG FOR ADDITIONAL INFORMATION. HWS HWR HWS 2 1/2" "COLD SIDE" TO SPA SYSTEM BY POOL CONTRACTOR. HX-3 SEE POOL MECHANICAL PIPING SCHEMATICS THIS DWG FOR ADDITIONAL INFORMATION. 1 3/4" HWS/R 2" HWS/R DHU-2 1 REVISIONS 2 ENLARGED MECHANICAL ROOM PLAN BASE BIDS NO.1-3 SCALE: 1/4" = 1'-0" 2 REC CENTER MECHANICAL PIPING DIAGRAM SCALE: N.T.S. F:\Loftus LLC Project Files\_2012\ DLA - Tippin Gynasium - Clarion\b. Drawings\Mech\H4.02.dwg 1/8/2015 3:29 PM TO POOL BY POOL CONTRACTOR 5'-0" MAX. CPVC POOL CONTRACTOR STOPPING POINT HEATER BOOSTER PUMP AND FLOW INTERLOCK 5'-0" MAX. CPVC POOL CONTRACTOR STOPPING POINT FROM TO ** FROM TO * * TO DEHUMIDIFICATION SYSTEM DHU-1, 90 GPM, 35 FT HEAD, 2 HP, 460 V-3Ø-60 HZ ** TO WATER TO WATER HEAT EXCHANGER. COLD SIDE GPM AND TEMPERATURE TO BE SPECIFIED BY POOL CONTRACTOR. HOT SIDE WATER FLOW FROM BUILDING HEATING SYSTEM. 200 GPM, 180 ENTERING WATER, 160 LEAVING WATER. COMPETITION POOL/ MECHANICAL PIPING SCHEMATIC HEATER BOOSTER PUMP AND FLOW INTERLOCK FROM FILTRATION EQUIPMENT BY POOL CONTRACTOR TO POOL BY POOL CONTRACTOR 5'-0" MAX. CPVC POOL CONTRACTOR STOPPING POINT HEATER BOOSTER PUMP AND FLOW INTERLOCK 5'-0" MAX. CPVC POOL CONTRACTOR STOPPING POINT FROM TO ** FROM TO * * TO DEHUMIDIFICATION SYSTEM DHU-2, 75 GPM, 35 FT HEAD, 1 1/2 HP, 460 V-3Ø-60 HZ ** TO WATER TO WATER HEAT EXCHANGER. COLD SIDE GPM AND TEMPERATURE TO BE SPECIFIED BY POOL CONTRACTOR. HOT SIDE WATER FLOW FROM BUILDING HEATING SYSTEM. 20 GPM, 180 ENTERING WATER, 140 LEAVING WATER. RECREATIONAL POOL/ MECHANICAL PIPING SCHEMATIC 3 SCALE: N.T.S. 4 SCALE: N.T.S. 5 SCALE: N.T.S. HEATER BOOSTER PUMP AND FLOW INTERLOCK FROM FILTRATION EQUIPMENT BY POOL CONTRACTOR TO SPA BY POOL CONTRACTOR 5'-0" MAX. CPVC POOL CONTRACTOR STOPPING POINT FROM TO * HEATER BOOSTER PUMP AND FLOW INTERLOCK * TO WATER TO WATER HEAT EXCHANGER. COLD SIDE GPM AND TEMPERATURE TO BE SPECIFIED BY POOL CONTRACTOR. HOT SIDE WATER FLOW FROM BUILDING HEATING SYSTEM. 40 GPM, 180 ENTERING WATER, 140 LEAVING WATER. SPA SYSTEM/ MECHANICAL PIPING SCHEMATIC FROM FILTRATION EQUIPMENT BY POOL CONTRACTOR DRAWN BY CHECKED BY COMMONWEALTH OF PENNSYLVANIA DEPARTMENT OF GENERAL SERVICES HARRISBURG, PENNSYLVANIA PROJECT NO. D.G.S PHASE 1 Renovation and Expansion of Tippin Gymnasium Clarion University, Clarion, Clarion County, Pennsylvania DATE SCALE Consultant's Signature PARTNERSHIP Joint Venture FOSTER PLAZA 9, SUITE HOLIDAY DRIVE PITTSBURGH, PA ENLARGED MECHANICAL ROOM & PIPING SCHEMATICS BASE BIDS NO.1-3 August 1, 2014 DRAWING NO. H4.02 Date Proj. No:

24 WC-1 1 1/2" CW, 3/4" HW UP 2" VENT UP WC-1 EX 4" WASTE UP FD-1 L-2 4" UR-1 L-2 FD-1 EX 4" F:\Loftus LLC Project Files\_2012\ DLA - Tippin Gynasium - Clarion\b. Drawings\Plumb\P1.09.dwg EX 4" EX 4" EX 4" EX 4" EX SAN 1 DN CONNECT TO EXISTING SANITARY PIPING FOUNDATION WEST BASE BID NO.1 SCALE: 1/8" = 1'-0" (UPPER LEVEL ELEV 1490'-0" LOWER BASECMENT 1453'-8") 1/9/2015 4:37 PM DLA/ GUND PARTNERSHIP Joint Venture FOSTER PLAZA 9, SUITE HOLIDAY DRIVE PITTSBURGH, PA TEL TIPPIN GYM Proj. No:

25 3" VENT UP 2" 1 1/4" 1/2" 1 1/4" 1/2" HW & 1/2" CW UP TO SINK 140 TBALL KERS 3B 3/4" 3/4" 1 1/2" 1 1/2" WRESTLING LOCKERS 246B 2" 2" 1 1/2" 3/4" ATSW OFFICE ATSW 247 3/4" ATSW OFFICE F:\Loftus LLC Project Files\_2012\ DLA - Tippin Gynasium - Clarion\b. Drawings\Plumb\P1.12.dwg EWC-1 PD STORAGE H 244 2" UP HPE OFFICE " 1 JAN. 245 MR-1 HPE RECEPTION 233 2" VESTIBULE 246A 2" PUMPED DISCHARGE FROM SP-2 HPE OFFICE GROUND LEVEL WEST BASE BID NO.1 SCALE: 1/8" = 1'-0" (ELEV 1478'-8") 2" HPE OFFICE " VENT DN 1 1/9/2015 4:41 PM DLA/ GUND PARTNERSHIP Joint Venture FOSTER PLAZA 9, SUITE HOLIDAY DRIVE PITTSBURGH, PA TEL TIPPIN GYM Proj. No:

26

27 K.8 K.3 K F36 F36 T/FTG. = 1478'-0" T/FTG. = 1478'-0" F36 P1 P1 1/8/2015 8:25:46 AM FILE: C:\01 - AES Revit Projects\12080_00^R14 CLARION TIPPIN STRUCT - CF_Brian Smith.rvt 23.5 DLA/ GUND PARTNERSHIP Joint Venture FOSTER PLAZA 9, SUITE HOLIDAY DRIVE PITTSBURGH, PA TEL T/FTG. = 1473'-6" F36 T/PIER = 1478'-0" T/FTG. = 1478'-0" TIPPIN GYM BULLETIN NO.5 D.G.S. PROJ. NO.: , PHASE 1 DATE: F36 DLA+ PROJECT NO: F36 T/PIER = 1478'-0" T/FTG. = 1473'-6" T/FTG. = 1478'-0" PARTIAL FOUNDATION PLAN - BASEMENT LEVEL - EAST - 1/8" BASE BID NO. 1, NO. 2 & NO. 3 1/8" = 1'-0" FOUNDATION PLAN CUAC PROJECT # SCALE: Project Number SKETCH NO. 1/8" = 1'-0" SSK-004

28 UP TYP. 4 SIDES 125 S BACKWASH CATCH BASIN 8" CONC. WALL REINF. PER SECT. 125/S4.2 1/8/2015 8:26:09 AM FILE: C:\01 - AES Revit Projects\12080_00^R14 CLARION TIPPIN STRUCT - CF_Brian Smith.rvt 23 DLA/ GUND PARTNERSHIP Joint Venture FOSTER PLAZA 9, SUITE HOLIDAY DRIVE PITTSBURGH, PA TEL K.8 TIPPIN GYM K.3 PARTIAL GROUND FLOOR PLAN EAST -1/8 BASE BID NO. 1, NO. 2 & NO. 3 1/8" = 1'-0" BULLETIN NO.5 D.G.S. PROJ. NO.: , PHASE 1 DATE: DLA+ PROJECT NO: K GROUND FLOOR CUAC PROJECT # SCALE: Project Number SKETCH NO. 1/8" = 1'-0" SSK-005

29 L.7 M M.3 M.5 M BACKWASH CATCH BASIN 8" CONC. WALL REINF. PER SECT. 125/S S4.2 TYP. 6 SIDES 8.3 1/8/2015 7:21:26 AM FILE: C:\01 - AES Revit Projects\12080_02^R14 CLARION REC STRUCT - CF_Brian Smith.rvt 8.8 DLA/ GUND PARTNERSHIP Joint Venture FOSTER PLAZA 9, SUITE HOLIDAY DRIVE PITTSBURGH, PA TEL TIPPIN GYM BULLETIN NO.5 D.G.S. PROJ. NO.: , PHASE 1 PARTIAL GROUND FLOOR PLAN - REC POOL 1/8" = 1'-0" GROUND FLOOR DATE: DLA+ PROJECT NO: CUAC PROJECT # SCALE: Project Number SKETCH NO. 1/8" = 1'-0" SSK-006

30

31 S1 ELEV. T/SLAB = 1478'-8" S1 ELEV. T/SLAB = 1474'-0" 14'-6 7/8" 1/8/ :02:39 AM FILE: C:\01 - AES Revit Projects\12080_00^R14 CLARION TIPPIN STRUCT - CF_Brian Smith.rvt A 4 DLA/ GUND PARTNERSHIP Joint Venture FOSTER PLAZA 9, SUITE HOLIDAY DRIVE PITTSBURGH, PA TEL '-11 5/8" C8X11.5 C8X11.5 C8X '-0 3/8" MC12X10.6 STAIR STRINGER MC12X S4.1 MC12X /8" MW1 TYP. 4 SIDES NOTE 8 J.2 J J.5 K K.6 PARTIAL GROUND FLOOR PLAN - WEST - 1/8" BASE BID NO. 1, NO. 2 & NO. 3 1/8" = 1'-0" TIPPIN GYM BULLETIN NO.5 D.G.S. PROJ. NO.: , PHASE 1 DATE: DLA+ PROJECT NO: C8X18.75 MC12X10.6 GROUND FLOOR BPL 1/2X6X6 TYP. CUAC PROJECT # SCALE: Project Number SKETCH NO. 1/8" = 1'-0" SSK-008

32 K.6 K1 L M 1/8/ :02:00 AM FILE: C:\01 - AES Revit Projects\12080_00^R14 CLARION TIPPIN STRUCT - CF_Brian Smith.rvt DLA/ GUND PARTNERSHIP Joint Venture FOSTER PLAZA 9, SUITE HOLIDAY DRIVE PITTSBURGH, PA TEL TIPPIN GYM BULLETIN NO.5 D.G.S. PROJ. NO.: , PHASE 1 4" CONC. SLAB ON RIGID INSULATION SUPPORTED BY EXIST. SLAB ON GRADE ELEV. T/NEW SLAB = 1469'-4" ELEV. T/ EXIST. SLAB = 1468'-0"+/- SLAB OCCURS BENEATH STAIR FRAMING & EXIST. FLOOR SHOWN PARTIAL GROUND FLOOR PLAN - WEST - 1/8" BASE BID NO. 1, NO. 2 & NO. 3 1/8" = 1'-0" GROUND FLOOR DATE: DLA+ PROJECT NO: CUAC PROJECT # SCALE: Project Number SKETCH NO. 1/8" = 1'-0" SSK-009

33