Adjustable Positive Linear Regulator Thru-Hole (TO-257AA)

Size: px

Start display at page:

Download "Adjustable Positive Linear Regulator Thru-Hole (TO-257AA)"

Patience Lisa Townsend
5 years ago
Views:

1 PD able Positive Linear Regulator Thru-Hole (TO-257AA) Product Summary Part Number Input Voltage Range able Output Voltage Package 4.25V to 41.25V 1.2V to 37V TO-257 (Isolated) 4.25V to 41.25V 1.2V to 37V TO-257 (Non-Isolated) 1.5A Description This three terminal positive regulator is supplied in a hermetically sealed metal package. All protective features are designed into the circuit, including thermal shutdown, current-limiting, and safe-area control. With heat sinking, these devices can deliver up to 1.5 amps of output current. This unit also features output voltages that can be trimmed from 1.2 volt to 37 volts using external resistors. TO-257AA Features: n able Output Voltage n Eliminates Stocking Fixed Voltages n Built-In Thermal Oveload Protection n Short Circuit Current Limiting n Isolated / Non-Isolated Hermetic TO-257AA Package ensures High Reliability Absolute Maximum Tc = 25 C Parameter Symbol Value Units Input-Output Voltage Differential -O 40 Input Voltage Range 4.25 to V Output Voltage Range UT 1.2 to 37 Output Current I OUT 1.5 A Power T C = 86 C Thermal Resistance, Junction to Case P DC R θjc Power T A = 25 C Thermal Resistance, Junction to Ambient P DA R θja W C/W Operating Junction Temperature Range -55 to 150 Storage Temperature Range T STG -65 to 150 C Lead Temperature Soldering (10 seconds maximum) T L /20/06

2 , Electrical Characteristics -55 CÃdÃT A dã125 C, = 8.0mA (Unless Otherwise Specified) Parameter Symbol Test Conditions Min. Max. Units V DIFF = 3.0V, T A = 25 C Reference Voltage V REF V DIFF = 3.3V e V V DIFF = 40V e Line Regulation c R LINE 3.0V V DIFF 40V, UT = V REF, T A = 25 C V V DIFF 40V, UT = V REF e V DIFF = 3.0V, 10mA 1.5A, T A = 25 C V DIFF = 3.3V, 10mA 1.5A e V DIFF = 40V, 10mA 300mA, T A = 25 C V DIFF = 40V, 10mA 195mA e Load Regulation c R LOAD mv Thermal Regulation V RTH = 14.6V, =1.5A, P D = 20W, t = 20ms, T A = 25 C Ripple Rejection d R N f = 120Hz, UT = V REF, C ADJ = 10µF e 66 - db V DIFF = 3.0V, T A = 25 C ment Pin Current I ADJ V DIFF = 3.3V e V DIFF = 40V e V DIFF = 3.0V, 10mA 1.5A, T A = 25 C V DIFF = 3.3V, 10mA 1.5A e µa ment Pin I ADJ V DIFF = 40V, 10mA 300mA, T A = 25 C Current Change V DIFF = 40V, 10mA 195mA e V V DIFF 40V, T A = 25 C V V DIFF 40V e V DIFF = 3.0V, UT =1.4V (forced), T A = 25 C Minimum Load Current MIN V DIFF = 3.3V, UT =1.4V (forced) e ma V DIFF = 40V, UT =1.4V (forced) e Current Limit d I CL V DIFF = 15V e V DIFF = 40V, T A = 25 C A Notes Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. If not tested, shall be guaranteed to specific limits. ƒ The specifications are applied over the full operating temperature range. 2

3 ,, OUTPUT VOLTAGE CHANGE (%) = 15V = 10V = 1.5A = 0.5A -1.0 I O, OUTPUT CURRENT (A) = 25 C = 150 C = -55 C , INPUT - OUTPUT VOLTAGE DIFFERENTIAL ( V dc ) Fig. 1 Load Regulation Fig. 2 Current Limit I Adj, ADJUSTMENT PIN CURRENT (µa) , INPUT-OUTPUT VOLTAGE DIFFERENTIAL (V dc ) = 100mV = 20mA = 1.5A = 1.0A = 200mA = 500mA 1.0 Fig. 3 ment Pin Current Fig. 4 Dropout Voltage V ref, REFERENCE VOLTAGE (V) I B, QUIESCENT CURRENT (ma) = -55 C = 25 C 3.0 = 150 C , INPUT - OUTPUT VOLTAGE DIFFERENTIAL ( V dc ) Fig. 5 Temperature Stability Fig. 6 Minimum Operating Current 3

4 , Fig. 7 - Standard Application C IN * 0.1µF I ADJ UT R1 240 C OUT ** 1.0µF R2 * C IN is required if regulator is located an appreciable distance from power supply filter. ** C OUT is not needed for stability, however it does improve transient response. UT = 1.25V(1 (R2/R1)) I ADJ (R2) Since I ADJ is not controlled to less than 100µA, the error associated with this term is negligible in most applications. Typical Applications Fig. 8 able Current Limiter 25V UT R1 I O 1.25 R2 D IN 1N4001 To provide current limiting of I O to the system ground, the source of the FET must be tied to a negative voltage below -1.25V. 100 D IN 1N4001 R2 = V REF / I DSS, R1 = V REF / (I OMAX I DSS) < (BV DSS 1.25V V SS ) (MIN I DSS ) < I O < 1.5A 2N5640 As shown 0 < I O < 1.0A V SS 4

5 Fig. 9 5V Electronic Shut Down Regulator, 1N4002 D µF MPS2222 1K TTL Control Minimum UT = 1.25V D1 protects the device during an input short circuit Fig. 10 Slow Turn-On Regulator 240 1N K R2 MPS µF Fig. 11 Current Regulator R1 I OUT I ADJ I OUT = (V REF / R1) I ADJ = (1.25V / R1) I ADJ 10mA < I OUT < 1.5A 5

6 , Case Outline and Dimensions TO-257AA [.420] [.410] A 3.81 [.150] 3X Ø 3.56 [.140] 5.08 [.200] 4.83 [.190] 0.13 [.005] 1.14 [.045] 0.89 [.035] [.537] [.527] [.665] [.645] [.430] [.410] B C [.625] [.500] 0.71 [.028] MAX [.100] 2X 3X Ø 0.88 [.035] 0.64 [.025] Ø 0.50 [.020] C A B 3.05 [.120] NOTES : 1. DIMENSIONING & TOLERANCING PER ANSI Y14.5M CONTROLLING DIMENSION: INCH. 3. DIMENSIONS ARE SHOWN IN MILLIMETERS [INCHES]. 4. OUTLINE CONFORMS TO JEDEC OUTLINE TO-257AA. PIN ASSIGNMENTS ISOLATED Front View NON-ISOLATED Front View Pin # Description Pin # Description 1 ADJUST 1 ADJUST 2 OUTPUT 2 OUTPUT 3 INPUT 3 INPUT Tab ISOLATED Tab OUTPUT Device Number Part Numbering Nomenclature OM 7602 S/N T M Screening M = MIL-PRF P = Minimal Screening Package Code T = TO-257AA Isolated / Non-Isolated S = Isolated N = Non-Isolated WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, Tel: (310) IR LEOMINSTER: 205 Crawford St., Leominster, Massachusetts 01453, Tel: (978) Data and specifications subject to change without notice.10/

Parameter Symbol Value Units

Parameter Symbol Value Units PD-97308 Adjustable Low Dropout Positive Voltage Regulator OM186ST VADJ, 1.5A Product Summary Part Number Output Voltage Output Current Package OM186ST Adjustable 1.5A TO-257AA TO-257AA Description These