R E V ENGINEERING /DRAFTING STANDARDS MASTER INDEX ES STD. NO. ES- DESCRIPTION

Transcription

1 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R 07 UPDATD IN ACCORDANC WITH 2008 STANDARDS ZJW 12/5/07 Y-0528s001 STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID STD. NO. S- R. DSCRIPTION 001 MASTR INDX 002 CHANG NOTIC RLAS PROCDURS 003 LCTRICAL 004 DRAWINGS GNRAL INSTRUCTIONS 005 BILL OF MATRIAL (under development) 006 SHT MTAL 007 NUMBR ASSIGNMNT AND NAMING CONNTIONS 008 DIMNSIONING AND TOLRANCING 009 RHM SHT MTAL STL ORDRING GUID (DCIMAL QUIALNT) OFTN RFRRD TO DRAWINGS & INSTRUCTIONS COPPR TUB FORMING SPCIFICATIONS 019 SAFTY LABL GUIDLINS 020 PRINTD MATRIALS SCRW HOL SIZS DRI & CLARANC COIL SPCIFICATIONS CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL.: DR. BY: DAT : ZJW RLAS No.: MATRIAL: NGINRING /DRAFTING STANDARDS MASTR INDX PART NO. SHT NO. R. S S-001-_1.DOC

2 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R 03 ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID SHT DSCRIPTION 1 CHANG NOTIC NUMBR ASSIGNMNTS 2 CHANG NOTIC FORMAT 3 PRODUCT LIFCYCL 4 ADANC PLANNING RLAS OF PRODUCTS 5 PRLIMINARY RLAS OF PRODUCTS 6 PR-PILOT RLAS OF PRODUCTS 7 PILOT RLAS OF PRODUCTS 8 FINAL RLAS OF PRODUCTS 9 OBSOLSCNC RLAS OF PRODUCTS 10 MISCLLANOUS RLAS OF CHANGS TO PRODUCTS 11 ISSUING CHANG NOTIC MAIL NOTIFICATIONS CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/14/08 RLAS No.: MATRIAL: CHANG NOTIC RLAS PROCDURS PART NO. SHT NO. R. S-002- INDX 03 S-002_INDX.DOC

3 03 04 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS ADDD "NL=NUO LARDO CHANG NOTICS" TO UNIT TYP PRFIX. ZJW 8/14/2008 Y-0528S003 08/05/2010 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL 1/32 -ANGULAR DCIMAL.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID NUMBR ASSIGNMNTS FOR PRODUCT CHANG NOTICS & NW PRODUCT RLASS Change Notice number assignment shall be done electronically in Change Notice number assignment files _ANOASS.xls. There is an assignment file for each of the Unit Type Prefixes (see list below). The files can be found in sub directories of O:\CHGNOT\. The subdirectories are also named for the Unit Type Prefix. For example if you are creating a change notice for an split system A/C unit, the file would be O:\CHGNOT\A-\_ANOASS.XLS A-1006S004 Supplement Number Always S followed by three numeric characters Change Notice Number - projects will have an assigned Number pertaining only to that Project and will be supplemented. (ex: A-1006S005) Dash Unit Type Prefix A = Air Conditioning B = Blower Units C = Coils = lectric Furnaces G = Gas Furnaces H = Air Handlers O = Oil Furnaces P = Heat Pumps Q = Packaged Heat Pumps (both J and Q models) R = Rooftops (both K and R models) S = Self Contained (both L and S models) X = Accessory Items Y = Miscellaneous Releases (Changes covering multiple unit types) NL = Nuevo Laredo Change Notices Once a Change Notice number has been assigned to a product, this number will be supplemented for the life of the product, thus keeping all the revisions together. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : JPH PRODUCT CHANG NOTICS & NW PRODUCT RLAS (CHANG NOTIC NUMBRING SYSTM) RLAS No.: MATRIAL: PART NO. SHT NO. 1 R. S s-002_1.doc

4 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID S SHT 2C FOR NUMBRING XPLANATION CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: DAT : RLAS NO.: CHANG NOTIC PROCDUR DATA PART NO. SHT NO. 2A R. S S-002_2a.doc

5 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : RLAS No.: MATRIAL: FIRST ARTICL INSPCTION AND FIRST PART APPROAL PROCDUR PART NO. SHT NO. 2B R. S S-002_2b.doc

6 03 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID CHANG NOTIC PROCDUR DATA 1. R&D PROJCT NUMBR Indicate Project Number that work listed on Change Notice was charged to. This can be a product maintenance number or a specific project number. 2. PRODUCT CHANG NOTIC or Indicate Product Change Notice or New Product Release NW PRODUCT RLAS with an X. 3. PRODUCT Indicate type of product, i.e. (Reference 2 nd letter of model no. prefix). (Reference ADS ) A- Air Conditioner O- Oil Furnace C- Coils P- Heat Pump D- Ductless Fan Coil R- Rooftop - lectric Furnace S- Self Contained Packaged Units G- Gas Furnace T- Tubing H- Air Handler X- Accessories 4. PAG NO. Indicate page number including total number of pages. 5. CHANG NOTIC NO. Indicate change notice number. If supplement to the original change notice; indicate with an S before the supplement number, i.e. (A-1008S002) 6. DISTRIBUTION DAT Date the Change Notice is distributed from R&D ngineering. 7. RLASD BY Person issuing the Change Notice. 8. PRODUCT DSIGNATION Models should be indicated by as much of the model number as needed to clearly convey the models affected by the changes. 9. ITM Use alpha designation to segregate various changes. This is usually reserved for segregation of Work Orders. 10. DRAWING NUMBR Indicate Prefix and Base number for drawing or MS for Bill of Material Changes CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/14/08 RLAS No.: MATRIAL: CHANG NOTIC PROCDUR DATA PART NO. SHT NO. 2C R. S S-002_2C.DOC

7 03 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID CHANG NOTIC PROCDUR DATA 11. SUFFIX Indicate drawing number suffix. 12. SHT Indicate Sheet number of drawing (if applicable). 13. R. Indicate Revision number of drawing. 14. DSCRIPTION This area is provided to List the fabricated part, component or drawing title and to describe the nature of the revision. Any specific instructions regarding inventory should be stated in this area. 15. FPA FPA (First Part Approval) Indicate Y for Required or N for not required. Decision for FPA to be determined by Design ngineer. 16. FAI FAI (First Article Inspection) Indicate Y for Required or N for not required. Decision for FAI is to be determined by a Purchasing Agent. 17. USAG See Sheet 2B of this standard (S-002). 18. IMPLMNT BY DAT See Sheet 2B of this standard (S-002). Implement by date will Be determined by MDACC/Design ngineer. 19. RLAS SIGNATURS All signatures will be on front page of change notice. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/14/08 RLAS No.: MATRIAL: CHANG NOTIC PROCDURS DATA PART NO. SHT NO. 2D R. S S-002_2D.DOC

8 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : RLAS No.: MATRIAL: PRODUCT LIFCYCL PART NO. SHT NO. 3 R. S S-002_3.doc

9 03 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID PROCDUR FOR ADANCD PLANNING RLAS OF NW PRODUCTS TH ADANCD PLANNING RLAS WILL CONSIST OF INDIIDUAL DRAWINGS FOR TOOLING AND/OR COMPONNTS, TC. WITH INFORMATION AS TO HOW TH PARTS AR RLATD TO SPCIFIC MODLS AND WOULD NOT RQUIR A COMPLT BILL OF MATRIAL. TH ADANCD PLANNING RLAS WILL B ISSUD ON A LIMITD DISTRIBUTION. DRAWINGS SHOULD B ISSUD TO RPRSNTATIS OF MANUFACTURING NGINRING, PURCHASING, MARKTING, AND RSARCH & DLOPMNT IN ALL PLANTS AFFCTD BY TH CHANG. ACH DRAWING SHALL B MARKD WITH TH FOLLOWING STATMNT: ADANCD PLANNING RLAS A CHANG NOTIC NUMBR WILL B ASSIGND TO THIS RLAS; HOWR INDIIDUAL DRAWINGS WILL NOT B SCANND INTO TH SYSTM UNTIL TH PRLIMINARY RLAS. TH CHANG NOTIC WILL LIST DRAWING NUMBRS AND DSCRIPTIONS, IDNTIFICATION OF PRODUCT LINS (MODL NUMBR) AND ANY ADDITIONAL INFORMATION WHICH WOULD B PRTINNT. TH CHANG NOTIC SHALL INCLUD TH FOLLOWING STATMNT: THIS CHANG NOTIC IS BING ISSUD AS AN ADANCD PLANNING RLAS TO LIMITD DISTRIBUTION TO ALLOW IDNTIFICATION OF TOOLING AND OTHR MANUFACTURING RQUIRMNTS FOR TH MODLS LISTD ABO. THS DRAWINGS AR TO B DSTROYD UPON RCIPT OF TH PRLIMINARY RLAS CORING THIS QUIPMNT. RISION NUMBRS ON DRAWINGS ISSUD ON ADANCD PLANNING RLASS WILL B PR S-004, RISION NUMBR/RISION LTTR PROCDURS. AFTR TH ADANCD RLAS IS MAD, ANY RISIONS OR UPDATS TO THS PARTS WILL B NOTD ON TH DRAWINGS AND RLASD AS A RISION ON A SUPPLMNTAL ADANCD PLANNING RLAS CHANG NOTIC OR ON TH PRLIMINARY RLAS CHANG NOTIC SUPPLMNTING TH RLAS NUMBR. TH CHANG NOTIC MUST B APPROD BY TH DSIGN SRICS MANAGR OR DSIGN, A DSIGNR THAT IS NOT INOLD IN MAKING TH RLAS, TH APPROPRIAT NGINR AND NGINRING MANAGR, AGNCY LIAISON, AND DIISION PURCHASING RPRSNTATI, WHN RQUIRD. S SHT 4C FOR XAMPL. NOT: ANY DRAWINGS RLASD ON AN ADANCD PLANNING RLAS MUST B RLASD ON A SUBSQUNT CHANG NOTIC TO ALLOW PROPR DISTRIBUTION. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: 8/14/08 RLAS No.: MATRIAL: PROCDUR FOR ADANCD PLANNING RLAS OF NW PRODUCTS PART NO. SHT NO. 4A R. S S-002_4A.DOC

10 03 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID PROCDUR FOR ADANCD PLANNING RLAS SUPPLMNT OF NW PRODUCTS FOLLOWING SAM PROCDUR AS ADANCD PLANNING RLAS XCPT AS NOTD BLOW: 1. DISTRIBUT SUPPLMNT TO SAM LIMITD DISTRIBUTION AS ADANCD PLANNING RLAS STATING THAT TH DRAWINGS ATTACHD RPLAC PRIOUSLY DISTRIBUTD ADANCD PLANNING RLAS DRAWINGS. CHANG NOTICS MUST STAT THAT ALL AFFCTD PRINTS FROM PRIOUS RLASS MUST B DSTROYD. NOT: ANY ADDITIONAL SUPPLMNTS RQUIRD WILL FOLLOW SAM PROCDUR AS ABO. NOT: ANY DRAWINGS RLASD ON AN ADANCD PLANNING RLAS MUST B RLASD ON A SUBSQUNT CHANG NOTIC TO ALLOW PROPR DISTRIBUTION. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/14/08 RLAS No.: MATRIAL: PROCDUR FOR ADANCD PLANNING RLAS OF NW PRODUCTS PART NO. SHT NO. 4B R. S S-002_4B.DOC

11 03 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT ADDD TO WORD FORMAT, UPDATD IN ACCORDANC WITH 2008 PROCDURS JHB STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: DAT : RLAS NO.: PROCDUR FOR ADANCD PLANNING RLAS OF NW PRODUCTS PART NO. SHT NO. 4C R. S S-002_4C.doc

12 03 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID PROCDUR FOR PRLIMINARY RLAS OF NW PRODUCTS A PRLIMINARY RLAS IS A RLAS OF ALL AAILABL DATA (DRAWINGS AND BILLS OF MATRIALS) ON A NW PRODUCT OR PRODUCT LIN, PRIOR TO PR-PILOT OR PILOT RUN, AND AGNCY TSTING/CRTIFICATION. ITMS THAT AR NOT AAILABL AT TH TIM OF TH INITIAL PRLIMINARY RLAS WILL B NOTD ON TH CHANG NOTIC WRIT UP. PRINTS FOR TH PRLIMINARY RLAS WILL NOT B MARKD PRLIMINARY. TH PRLIMINARY RLAS WILL B ISSUD TO FULL CHANG NOTIC DISTRIBUTION FOR TH PRODUCT LIN. A CHANG NOTIC NUMBR WILL B ASSIGND TO THIS RLAS AND INDIIDUAL DRAWINGS WILL B SCANND INTO TH SYSTM FOR TH PRLIMINARY RLAS. TH CHANG NOTIC WILL LIST DRAWING NUMBRS AND DSCRIPTIONS, IDNTIFICATION OF PRODUCT LINS (MODL NUMBR) AND ANY ADDITIONAL INFORMATION WHICH WOULD B PRTINNT. TH CHANG NOTIC SHALL INCLUD TH FOLLOWING STATMNT: THIS IS A PRLIMINARY RLAS FOR TH NW (DSCRIPTION OF PRODUCT OR PRODUCT LIN) MODLS LISTD ABO. SALABL INDICATOR FOR ND ITMS SHOULD B 1 (UNDR DLOPMNT). CHANGS TO THIS PRODUCT OR PRODUCT LIN THAT MIGHT B RQUIRD WILL B RLASD ON A SUBSQUNT CHANG NOTIC. ANY RISIONS TO DRAWINGS WILL B INDICATD BY AN UPDAT TO TH RISION LL. NO PRODUCTION UNITS CAN B SHIPPD FROM TH FACTORY UNTIL TH FINAL PRODUCT RLAS HAS BN ISSUD AND TH SALABL INDICATOR HAS BN ADJUSTD TO LL 4 (BUILDABL / SALABL / SHIPPABL) INDICATING TH COMPLTION OF (INDICAT AGNCY) CRTIFICATION/LISTING OF TH PRODUCT(S). RISION NUMBRS ON DRAWINGS ISSUD WILL B PR S-004, RISION NUMBR/RISION LTTR PROCDURS. ANY CHANGS MAD TO DRAWINGS AR TO B ISSUD BY CHANG NOTIC, SUPPLMNTING TH RLAS NUMBR AND SHALL CARRY TH ABO STATMNT. TH CHANG NOTIC MUST B APPROD BY TH DSIGN SRICS MANAGR OR DSIGN, A DSIGNR THAT IS NOT INOLD IN MAKING TH RLAS, TH APPROPRIAT NGINR AND NGINRING MANAGR, AGNCY LIAISON, AND DIISION PURCHASING RPRSNTATI, WHN RQUIRD. NOT: THR MAY B MULTIPL PRLIMINARY RLASS FOR NW PRODUCTS. S SHT 5B FOR XAMPL. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: 8/14/08 RLAS No.: MATRIAL: PROCDUR FOR PRLIMINARY RLAS OF NW PRODUCTS PART NO. SHT NO. 5A R. S S-002_5A.DOC

13 03 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT ADDD TO WORD FORMAT, UPDATD IN ACCORDANC WITH 2008 PROCDURS. JHB STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: DAT : RLAS NO.: PROCDUR FOR PRLIMINARY RLAS OF NW PRODUCTS PART NO. SHT NO. 5B R. S S-002_5B.doc

14 03 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID PROCDUR FOR PR-PILOT RLAS OF NW PRODUCTS A PR-PILOT RLAS IS A NOTIFICATION THAT OF ALL DATA (DRAWINGS AND BILLS OF MATRIALS) ON A NW PRODUCT OR PRODUCT LIN, HA BN OR AR BING RLASD TO SUPPORT MANUFACTURING S PR-PILOT RUN. TH PR-PILOT RLAS WILL B ISSUD TO FULL CHANG NOTIC DISTRIBUTION FOR TH PRODUCT LIN. A CHANG NOTIC NUMBR WILL B ASSIGND TO THIS RLAS AND INDIIDUAL DRAWINGS WILL B SCANND INTO TH SYSTM. TH CHANG NOTIC WILL LIST ANY RISD OR NW DRAWING NUMBRS AND DSCRIPTIONS, IDNTIFICATION OF PRODUCT LINS (MODL NUMBR) AND ANY ADDITIONAL INFORMATION WHICH WOULD B PRTINNT. TH CHANG NOTIC SHALL INCLUD TH FOLLOWING STATMNT: THIS IS A PR-PILOT RLAS FOR TH NW (DSCRIPTION OF PRODUCT OR PRODUCT LIN) MODLS LISTD ABO. SALABL INDICATOR FOR ND ITMS SHOULD B 2 (BUILDABL / NON-SALABL / NON-SHIPPABL). CHANGS TO THIS PRODUCT OR PRODUCT LIN THAT MIGHT B RQUIRD AS A RSULT OF TH PR-PILOT RUN WILL B RLASD ON A SUBSQUNT CHANG NOTIC. ANY RISIONS TO DRAWINGS WILL B INDICATD BY AN UPDAT TO TH RISION LL. NO PRODUCTION UNITS CAN B SHIPPD FROM TH FACTORY UNTIL TH FINAL PRODUCT RLAS HAS BN ISSUD AND TH SALABL INDICATOR HAS BN ADJUSTD TO LL 4 (BUILDABL / SALABL / SHIPPABL) INDICATING TH COMPLTION OF (INDICAT AGNCY) CRTIFICATION/LISTING OF TH PRODUCT(S). RISION NUMBRS ON DRAWINGS ISSUD WILL B PR S-004, RISION NUMBR/RISION LTTR PROCDURS. ANY CHANGS MAD TO DRAWINGS AR TO B ISSUD BY CHANG NOTIC, SUPPLMNTING TH RLAS NUMBR AND SHALL CARRY TH ABO STATMNT. TH CHANG NOTIC MUST B APPROD BY TH DSIGN SRICS MANAGR OR DSIGN, A DSIGNR THAT IS NOT INOLD IN MAKING TH RLAS, TH APPROPRIAT NGINR AND NGINRING MANAGR, AGNCY LIAISON, AND DIISION PURCHASING RPRSNTATI, WHN RQUIRD. S SHT 6B FOR XAMPL. PROCDUR FOR POST PR-PILOT RLAS OF NW PRODUCTS THIS PROCDUR IS TO B USD BTWN PR-PILOT AND PILOT RLASS, IF RQUIRD (BTWN PR-PILOT AND PILOT). FOLLOW SAM PROCDUR AS ABO XCPT FIRST LIN OF CHANG NOTIC WILL RAD: THIS IS A POST PR-PILOT RLAS FOR TH NW (DSCRIPTION OF PRODUCT OR PRODUCT LIN). CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: 8/14/08 RLAS No.: MATRIAL: PROCDUR FOR PR-PILOT AND POST PR-PILOT RLASS OF NW PRODUCTS PART NO. SHT NO. 6A R. S S-002_6A.DOC

15 03 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT ADDD TO WORD FORMAT, UPDATD IN ACCORDANC WITH 2008 PROCDURS. JHB STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: DAT : RLAS NO.: PROCDUR FOR PR-PILOT AND POST PR-PILOT RLASS OF NW PRODUCTS PART NO. SHT NO. 6B R. S S-002_6B.doc

16 03 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID PROCDUR FOR PILOT RLAS OF NW PRODUCTS A PILOT RLAS IS A NOTIFICATION THAT OF ALL DATA (DRAWINGS AND BILLS OF MATRIALS) ON A NW PRODUCT OR PRODUCT LIN, HA BN OR AR BING RLASD TO SUPPORT MANUFACTURING S PILOT RUN. TH PILOT RLAS WILL B ISSUD TO FULL CHANG NOTIC DISTRIBUTION FOR TH PRODUCT LIN. A CHANG NOTIC NUMBR WILL B ASSIGND TO THIS RLAS AND INDIIDUAL DRAWINGS WILL B SCANND INTO TH SYSTM. TH CHANG NOTIC WILL LIST ANY RISD OR NW DRAWING NUMBRS AND DSCRIPTIONS, IDNTIFICATION OF PRODUCT LINS (MODL NUMBR) AND ANY ADDITIONAL INFORMATION WHICH WOULD B PRTINNT. TH CHANG NOTIC SHALL INCLUD TH FOLLOWING STATMNT: THIS IS A PILOT RLAS FOR TH NW (DSCRIPTION OF PRODUCT OR PRODUCT LIN) MODLS LISTD ABO. SALABL INDICATOR FOR ND ITMS SHOULD B 3 (BUILDABL / SALABL / NON-SHIPPABL). CHANGS TO THIS PRODUCT OR PRODUCT LIN THAT MIGHT B RQUIRD AS A RSULT OF TH PILOT RUN WILL B RLASD ON A SUBSQUNT CHANG NOTIC. ANY RISIONS TO DRAWINGS WILL B INDICATD BY AN UPDAT TO TH RISION LL. NO PRODUCTION UNITS CAN B SHIPPD FROM TH FACTORY UNTIL TH FINAL PRODUCT RLAS HAS BN ISSUD AND TH SALABL INDICATOR HAS BN ADJUSTD TO LL 4 (BUILDABL / SALABL / SHIPPABL) INDICATING TH COMPLTION OF (INDICAT AGNCY) CRTIFICATION/LISTING OF TH PRODUCT(S). RISION NUMBRS ON DRAWINGS ISSUD WILL B PR S-004, RISION NUMBR/RISION LTTR PROCDURS. ANY CHANGS MAD TO DRAWINGS AR TO B ISSUD BY CHANG NOTIC, SUPPLMNTING TH RLAS NUMBR AND SHALL CARRY TH ABO STATMNT. TH CHANG NOTIC MUST B APPROD BY TH DSIGN SRICS MANAGR OR DSIGN, A DSIGNR THAT IS NOT INOLD IN MAKING TH RLAS, TH APPROPRIAT NGINR AND NGINRING MANAGR, AGNCY LIAISON, AND DIISION PURCHASING RPRSNTATI, WHN RQUIRD. S SHT 7B FOR XAMPL. PROCDUR FOR POST PILOT RLAS OF NW PRODUCTS THIS PROCDUR IS TO B USD BTWN PILOT AND FINAL PRODUCT RLASS, IF RQUIRD. FOLLOW SAM PROCDUR AS ABO XCPT FIRST LIN OF CHANG NOTIC WILL RAD: THIS IS A POST PILOT RLAS FOR TH NW (DSCRIPTION OF PRODUCT OR PRODUCT LIN). CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: 8/14/08 RLAS No.: MATRIAL: PROCDUR FOR PILOT AND POST PILOT RLASS OF NW PRODUCTS PART NO. SHT NO. 7A R. S S-002_7A.DOC

17 03 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT ADDD TO WORD FORMAT, UPDATD IN ACCORDANC WITH 2008 PROCDURS. JHB STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: DAT : RLAS NO.: PROCDUR FOR PILOT AND POST PILOT RLASS OF NW PRODUCTS PART NO. SHT NO. 7B R. S S-002_7B.doc

18 03 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID PROCDUR FOR FINAL PRODUCT RLAS OF NW PRODUCTS TH FINAL PRODUCT RLAS WILL INCLUD ANY NW OR RISD SPCIFICATIONS (DRAWINGS AND BILLS OF MATRIALS) ON A NW PRODUCT OR PRODUCT LIN RQUIRD DU TO TH PILOT RUN AND / OR AGNCY TSTING OR RQUIRMNTS. TH FINAL PRODUCT RLAS WILL B ISSUD TO FULL CHANG NOTIC DISTRIBUTION FOR TH PRODUCT LIN. A CHANG NOTIC NUMBR WILL B ASSIGND TO THIS RLAS AND INDIIDUAL DRAWINGS WILL B SCANND INTO TH SYSTM. TH CHANG NOTIC WILL LIST ANY RISD OR NW DRAWING NUMBRS AND DSCRIPTIONS, IDNTIFICATION OF PRODUCT LINS (MODL NUMBR) AND ANY ADDITIONAL INFORMATION WHICH WOULD B PRTINNT. TH CHANG NOTIC SHALL INCLUD TH FOLLOWING STATMNT: THIS IS A FINAL PRODUCT RLAS FOR TH NW (DSCRIPTION OF PRODUCT OR PRODUCT LIN) MODLS LISTD ABO. AGNCY APPROAL HAS BN RCID AS OF (DAT). TH ABO LISTD MODLS CAN NOW B SHIPPD. SALABL INDICATOR FOR ND ITMS SHOULD B 4 (BUILDABL / SALABL / SHIPPABL). ALL PRINTS AND SPCIFICATIONS RLASD ON CHANG NOTIC (NUMBR) AND ALL SUBSQUNT SUPPLMNTS FOR TH ABO MNTIOND MODLS RLASD PRIOR TO TH DAT OF THIS RLAS AR NOW CONSIDRD FINAL WITH TH INCLUSION OF ANY RISIONS OR ADDITIONS LISTD BLOW. RISION NUMBRS ON DRAWINGS ISSUD WILL B PR S-004, RISION NUMBR/RISION LTTR PROCDURS. ANY CHANGS MAD TO DRAWINGS AR TO B ISSUD BY CHANG NOTIC, SUPPLMNTING TH RLAS NUMBR AND SHALL CARRY TH ABO STATMNT. TH CHANG NOTIC MUST B APPROD BY TH DSIGN SRICS MANAGR OR DSIGN, A DSIGNR THAT IS NOT INOLD IN MAKING TH RLAS, TH APPROPRIAT NGINR AND NGINRING MANAGR, AGNCY LIAISON, PACKAGING NGINR AND DIISION PURCHASING RPRSNTATI, WHN RQUIRD. ALL FINAL RLASS MUST INCLUD TH ORALL PACKAGD DIMNSIONS AND WIGHTS OF TH MODLS BING RLASD. S SHT 8B FOR XAMPL. APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: 8/14/08 RLAS No.: MATRIAL: PROCDUR FOR FINAL PRODUCT RLAS OF NW PRODUCTS PART NO. SHT NO. 8A R. S S-002_8A.DOC

19 03 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT ADDD TO WORD FORMAT, UPDATD IN ACCORDANC WITH 2008 PROCDURS. JHB STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: DAT : RLAS NO.: PROCDUR FOR FINAL PRODUCT RLAS OF NW PRODUCT PART NO. SHT NO. 8B R. S S-002_8B.doc

20 03 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID PROCDUR TO OBSOLT PRODUCTS THIS RLAS WILL INCLUD TH ADS-5100 SHTS THAT CONTAIN TH MODLS THAT WILL BCOM OBSOLT. THIS RLAS WILL B ISSUD TO FULL CHANG NOTIC DISTRIBUTION FOR TH PRODUCT LIN. A CHANG NOTIC NUMBR WILL B ASSIGND TO THIS RLAS AND INDIIDUAL DRAWINGS WILL B SCANND INTO TH SYSTM. TH CHANG NOTIC SHALL INCLUD TH FOLLOWING STATMNT: THIS CHANG NOTIC OBSOLTS TH (DSCRIPTION OF PRODUCT OR PRODUCT LIN) MODLS. THS MODLS WILL NO LONGR B BUILT AFTR (DAT) PR RCN BULLTIN (NUMBR). SALABL INDICATOR FOR ND ITMS SHOULD B 5 (NON-BUILDABL / SALABL / SHIPPABL) SO THAT INNTORY CAN B XHAUSTD. AFTR XISTING INNTORY IS DPLTD, TH DMAND FORCASTING DPARTMNT WILL ADIS R&D SO THAT A CHANG NOTIC CAN B ISSUD TO ADJUST TH SALABL INDICATOR TO 6 (NON-BUILDABL / NON-SALABL / NON-SHIPPABL). RISION NUMBRS ON DRAWINGS ISSUD WILL B PR S-004, RISION NUMBR/RISION LTTR PROCDURS. TH CHANG NOTIC MUST B APPROD BY TH DSIGN SRICS MANAGR OR DSIGN, A DSIGNR THAT IS NOT INOLD IN MAKING TH RLAS, TH APPROPRIAT NGINR AND NGINRING MANAGR, AGNCY LIAISON, AND DIISION PURCHASING RPRSNTATI, WHN RQUIRD. S SHT 9B FOR XAMPL. UPON NOTIFICATION FROM DMAND FORCASTING THAT INNTORY IS DPLTD, A CHANG NOTIC WILL B ISSUD THAT SHALL INCLUD TH FOLLOWING STATMNT: THIS CHANG NOTIC OBSOLTS TH (DSCRIPTION OF PRODUCT OR PRODUCT LIN) MODLS. THS MODLS WILL NO LONGR B BUILT AFTR (DAT) PR RCN BULLTIN (NUMBR). XISTING INNTORY HAS BN DPLTD. SALABL INDICATOR FOR ND ITMS SHOULD B 6 (NON-BUILDABL / NON-SALABL / NON-SHIPPABL). S SHT 9C FOR XAMPL. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: 8/14/08 RLAS No.: MATRIAL: PROCDUR FOR OBSOLT PRODUCTS RLAS PART NO. SHT NO. 9A R. S S-002_9A.DOC

21 03 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT ADDD TO WORD FORMAT, UPDATD IN ACCORDANC WITH 2008 PROCDURS. JHB STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: DAT : RLAS NO.: PROCDUR FOR OBSOLT PRODUCTS RLAS PART NO. SHT NO. 9B R. S S-002_9B.doc

22 03 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT ADDD TO WORD FORMAT, UPDATD IN ACCORDANC WITH 2008 PROCDURS. JHB STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: DAT : RLAS NO.: PROCDUR FOR OBSOLT PRODUCTS RLAS PART NO. SHT NO. 9C R. S S-002_9C.doc

23 03 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID PROCDUR FOR ISSUING PRODUCT MAINTNANC CHANG NOTICS TH PRODUCT MAINTNANC CHANG NOTIC RLAS WILL INCLUD ANY NW OR RISD SPCIFICATIONS (DRAWINGS AND BILLS OF MATRIALS) ON A PRODUCT OR PRODUCT LIN. TH PRODUCT MAINTNANC CHANG NOTIC RLAS WILL B ISSUD TO FULL CHANG NOTIC DISTRIBUTION FOR TH PRODUCT LIN. A CHANG NOTIC NUMBR WILL B ASSIGND TO THIS RLAS AND INDIIDUAL DRAWINGS WILL B SCANND INTO TH SYSTM. TH CHANG NOTIC WILL LIST ANY RISD OR NW DRAWING NUMBRS AND DSCRIPTIONS, IDNTIFICATION OF PRODUCT LINS (MODL NUMBR) AND ANY ADDITIONAL INFORMATION WHICH WOULD B PRTINNT. RISION NUMBRS ON DRAWINGS ISSUD WILL B PR S-004, RISION NUMBR/RISION LTTR PROCDURS. TH CHANG NOTIC MUST B APPROD BY TH DSIGN SRICS MANAGR OR DSIGN, A DSIGNR THAT IS NOT INOLD IN MAKING TH RLAS, TH APPROPRIAT NGINR AND NGINRING MANAGR, AGNCY LIAISON, AND DIISION PURCHASING RPRSNTATI, WHN RQUIRD. S SHTS 10A AND 10B FOR XAMPLS. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: 8/14/08 RLAS No.: MATRIAL: PROCDUR FOR ISSUING PRODUCT MAINTNANC CHANG NOTICS PART NO. SHT NO. 10A R. S S-002_10A.DOC

24 03 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT ADDD TO WORD FORMAT, UPDATD IN ACCORDANC WITH 2008 PROCDURS. JHB STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: DAT : RLAS NO.: PROCDUR FOR ISSUING PRODUCT MAINTNANC CHANG NOTICS PART NO. SHT NO. 10B R. S S-002_10B.doc

25 03 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT ADDD TO WORD FORMAT, UPDATD IN ACCORDANC WITH 2008 PROCDURS. JHB STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: DAT : RLAS NO.: PROCDUR FOR ISSUING CHANG NOTIC MAIL NOTIFICATIONS PART NO. SHT NO. 10C R. S S-002_10c.doc

26 03 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID PROCDUR FOR ISSUING CHANG NOTIC MAIL NOTIFICATIONS CHANG NOTIC RLASS WILL B DISTRIBUTD IA MAIL TO TH CHANG NOTIC LIST AND TH RQUSTING NGINR. TH CHANG NOTIC MAIL SUBJCT LIN SHOULD INCLUD TH CN NUMBR, TH PROJCT NUMBR, AND TH PLANT(S) FFCTD: CN P-1054S006; PROJCT 7016; PLANT 24/26 TH BODY OF TH MAIL SHOULD INCLUD A BRIF DSCRIPTION OF TH CHANG NOTIC AND A HYPRLINK TO TH CHANG NOTIC: THIS CHANG NOTIC UPDAT TH BILL OF MATRIALS SO THAT ALL SOUND NCLOSURS FOR TH (-)ANL, (-)APL, (-)ARL, (-)ASL, (-)PNL, AND (-)PPL MODLS HA HAT SHILDS FOR CRANK CAS HATRS. IF TH CHANG NOTIC CORS ARIOUS UPDATS, BULLT POINTS OR ADDITIONAL DSCRIPTIONS MAY B RQUIRD. NOT: COPYING AND PASTING TH CHANG NOTIC FORM TO TH MAIL SHOULD B AOIDD. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: 8/14/08 RLAS No.: MATRIAL: PROCDUR FOR ISSUING CHANG NOTIC MAIL NOTIFICATIONS PART NO. SHT NO. 11 R. S S-002_11.DOC

27 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R 04 ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID SHT DSCRIPTION 1 SCTION I WIRING DIAGRAMS & SCHMATICS 2 SCTION II DIAGRAM SYMBOLS 3 SCTION III COMPONNT CODING & SCHMATIC SYMBOLS 4 CONDUCT SIZ S. KNOCK-OUT DIAMTR 5 HYCO STRAIN RLIF BUSHING APPLICATION 6 WIRING DIAGRAM/SCHMATIC GN. RQUIRMNTS 7 MOTOR LAD COLOR STANDARD RF INDX TRMINAL APPLICATIONS & TST PROCDUR ADS-6679 INDX WIR SPCIFICATION SHTS ADS-4314 CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : CT 12/79 RLAS No.: MATRIAL: LCTRICAL PART NO. SHT NO. R. S-003 INDX 04 S-003_INDX.DOC

28 02 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID NGINRING LCTRICAL STANDARDS SCTION I DIAGRAMS AND SCHMATICS A. Wiring Diagrams 1. The connection diagram shall consist of a proportional panel or box outline and shall show the general physical Layout of the panel or box mounted components. 2. ach component shall be represented by an enclosure as shown in Section II. ach enclosure shall depict the shape Connections of the component when possible. 3. ach component must have the same code as on the schematic. 4. Any unused terminals or contacts shall be shown. 5. All wiring must be identified by either color code or number. B. Wiring Schematics 1. Standard electrical symbols for all electrical components shall be used in accordance with Section I. 2. The symbols for all components shall be identified by an abbreviated term or term number combination in accordance with Section III. 3. The symbols and terms of Section I are maintained within the CAD system menu. If they are determined to be Inadequate, changes or additions may be made with the approval of the engineering managers. Use Form CAD The schematic shall show the internal circuiting of all electrical components in the control system with the exception of solid state components. 5. The schematic shall be drawn with vertical line representing the source of control power and all control devices shall be between these lines. 6. All motors, coils, etc. shall be shown on the right hand side of the schematic when possible. 7. The position of the symbols shall be arranged for clarity and need not indicate their physical location in relation to ach other or to their relationship to the equipment. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : CT 01/06 RLAS No.: MATRIAL: WIRING DIAGRAMS & SCHMATICS PART NO. SHT NO. 1A R. S S-003_1A.DOC

29 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R 04 ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PPROCDURS 8/14/2008 STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Section I Diagrams and Schematics, (continued) 8. The correct symbol shall be used to show each control on the equipment in its actual state of being energized or de-energized, which ever the case might be, with the main switch (power supply) de-energized. 9. If the switch or coil terminals of a device are numbered, these numbers shall appear on the schematic. 10. As a general rule, wiring should not be identified by color code or number. An exception to this would be shematics of wiring diagrams of units with a large quantity of wires, for example commercial units. In this case, schematic wire identification is necessary to aid in tracing wiring. C. Wire Identification Color Wires identified by color only shall use the color abbreviations. PLAIN BK Black BU Blue BR Brown **TRACR RD Red with White Tracer BK/YL Black with Yellow Tracer TC. *GR Green PU Purple RD Red WH White YL Yellow OR Orange GY Gray * Used for ground only. ** Tracer may be tape or strip. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : CT 01/86 RLAS No.: MATRIAL: WIRING DIAGRAMS & SCHMATICS PART NO. SHT NO. 1B R. S S-003_1B.DOC

30 02 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Section I Diagrams and Schematics, (Continued) CONTROL WIRING (PIGTAILS) FOR FILD CONNCTIONS SHALL B COLORD AS FOLLOWS: FOR CONNCTION TO COLOR **TRACR THRMOSTAT TRMINAL RD YLLOW ORANG R Y OR Y1 Y2 BK/WH OR/WH RD/WH W OR W1 W OR W1 W OR W1 GRAY W2 BK/GR G2 BLU BROWN B X **TRACR MAY B TAP OR STRIP. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : CT 01/86 RLAS No.: MATRIAL: WIRING DIAGRAMS & SCHMATICS PART NO. SHT NO. 1C R. S S-003_1C.DOC

31 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R 02 ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDUR 8/14/2008 STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Section I Diagram and Schematics, continued D. Notes 1. Line oltage Factory Optional (a.) Field (b.) 2. Low oltage Factory Optional (a.) Field (b.) Optional of Field Indicator on Diagrams a. Indicates wires for optional components which may or may not be factory installed. b. Indicates wires which are field installed. Uses whatever number of notes is needed to explain the schematic or diagram. Under no circumstances are there To be duplicate note numbers (two sets of notes both beginning with 1. xamples of notes which may appear are: a. Replacement fuses must be the same as factory supplied. b. Use copper conductor only. 3. Remove Jumper (J1) if... etc. 4. Fuse FU1 and FU2 are 10 amp type CC fuses. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : CT 01/86 RLAS No.: MATRIAL: WIRING DIAGRAMS & SCHMATICS PART NO. SHT NO. 1D R. S S-003_1D.DOC

32 SCTION II - DIAGRAM SYMBOLS TH SYMBOLS IN THIS SCTION AR TYPICAL SUGGSTION FOR CONSISTNCY WITHIN PRODUCTS, THY AR NOT INTNDD TO COR ALL NDS. THY MAYB MAINTAIND WITH TH CAD SYSTM MNU. ACH APPLICATION COULD B DIFFRNT. ALL SYMBOLS SHOULD B CLARLY MARKD AS TO THR USAG WITH ACCOMPANYING ABBRIATIONS AS NDD. OR TYPICAL CONTROL: SNSORS, LOW PRSSUR, HIGH PRSSUR. SWITCHS AND LOW AMBINT CONTROLS WITH INRAL LAD CONNCTIONS. THS CONTROLS WILL LIKLY B ACCOMPANID BY AN ABBRIATION SUCH AS LAC HP LP TDC SNS. 1 TYPICAL CONTROL: SUCH AS CONTROLS WITH LCTRONIC CIRCUITY OR RLAYS WITH QUICK CONNCT OR SCRW TRMINALS CONNCTIONS. SHOW ALL CONNCTIONS WHTHR USD OR NOT. CONNCTIONS WILL LIKLY B LABLD WITH NUMBRS OR LTTRS AND TH ILLUSTRATION SHOULD RFLCT THOS MARKINGS. 1 RLAY: R ALTRNAT SYMBOL- SWITCH CONFIGURATION SHOULD B SHOWN. SHOW ALL CONNCTIONS WHTHR USD OR NOT. CONNCTIONS WILL LIKLY B LABLD WITH NUMBRS OR LTTRS AND TH ILLUSTRATION SHOULD RFLCT THOS MARKINGS. L1 L2 L3 CONTACTOR: AUX CC IF AUXILIARY CONTACT IS SUPPLID SHOW IN SPARAT NCLOSUR. 01 RDRAWN AND UPDATD SYMBOLS. JHB "NR" "NR" JLC/CLT JAN. 86 DIAGRAM SYMBOLS SHT NO. 2A S

33 SCTION II - DIAGRAM SYMBOLS TRMINAL BLOCK:. CONNCTIONS WILL LIKLY B LABLD WITH NUMBRS OR LTTRS AND TH ILLUSTRATION SHOULD RFLCT THOS MARKINGS. TH LTTR TB AND A NUMRAL IF MTHR AR MOR THAN ON TRMINAL BLCOK WILL ACCOMPANY ACH TRMINAL. TRANSFORMR: SHOW PRIMARY AND SCONDARY OLTAGS AS UNIT IS MANUFACTURD. SHOW ALL PRIMARY AND SCONDARY WIR TAPS. SHOW BOTH THIR COLOR AND THR FUNCTION. INTRGRAL LADS AR SHOWN. GROUNDING LUG: CAPACITOR: 01 RDRAWN AND UPDATD SYMBOLS. JHB "NR" "NR" JLC/CLT JAN. 86 DIAGRAM SYMBOLS SHT NO. 2B S

34 SCTION II - DIAGRAM SYMBOLS QUICK CONNCT SCRW TRMINAL : OLTAG MAY ARY FUS BLOCK: WILL B ACCOMPID BY TH ABBRIATION FB PLUG: MAL PLUG: FMAL PLUG: CONNCTD MAL & FMAL WN: WIR NUT WIR SPLIC H, HATING LMNT - WILL B ACCOMPANID BY TH ABBRIATION H PTC : START ASSIST LIGHT: WILL B ACCOMPANID BY TH ABBRIATION LT PTC : START ASSIST 01 RDRAWN AND UPDATD SYMBOLS JHB "NR" "NR" JLC/CLT JAN. 86 DIAGRAM SYMBOLS S SHT NO. 2C 01

35 SCTION II - DIAGRAM SYMBOLS PANL MOUNTD FUS HOLDR: SHOW FUS SIZ IN CAP. SHOW FUS CALL OUT IN FRONT OF CAP OR IN CHART FORM. CARTRIDG FUS: STANDRD (ON TIM), I: NON, NOS. SHOW FUS SIZ INSID FUS FO IN CHART FORM. CARTRIDG FUS: TIM DLAY (DUAL LMNT) TYP, I: FRN, FRS. SHOW FUS SIZ INSID FUS OR IN CHART FORM. PLUG FUS: STANDRAD OR DUAL LMNT TYP, I: W OR S. SHOIW FUS SIZ INSID FUS OR IN CHART FORM. COMPRSSOR WITH OR WITHOUT PROTCTI MODUL. SHOW APPRPRIAT NUMBR OF LIN (POWR) LADS. TRMINAL MARKING NOT SHOWN FOR THR PHAS COMPRSSORS. MOTOR: SHOW APPROPRIAT NUMBR OF LIN (POWR) LADS. ON DUAL OLTAG MOTORS, SHOW DIAGRAM ONLY THOS LADS APPLICABL TO DIAGRAM OLTAG. SUPPLMNTAL WIRING DIAGRAM TO B ST UP AS RQUIRD FOR ALTRNAT WIRING. 01 RDRAWN AND UPDATD SYMBOLS. JHB "NR" "NR" JLC/CLT JAN. 86 DIAGRAM SYMBOLS SHT NO. 2D S

36 SCTION II - DIAGRAM SYMBOLS PLNUM BLOWR THRMOSTAT (PBT) - CONNCTIONS WILL LIKLY B LABLD WITH NUMBRS OR LTTRS AND TH ILLUSTRATION SHOULD RFLCT THOS MARKINGS. OIL SAFTY CONTROL WITH TIM DLAY (OSTC) - CONNCTIONS WILL LIKLY B LABLD WITH NUMBRS OR LTTRS AND TH ILLUSTRATION SHOULD RFLCT THOS MARKINGS. 01 RDRAWN AND UPDATD SYMBOLS. JHB "NR" "NR" JHB DIAGRAM SYMBOLS SHT NO. 2 S

37 06 ADDD AMPRAG SNSOR, BJW 07 UPDATD FORMAT, JHB "NR" "NR" JHB SHT NO. 3A LCTRICAL SCT. III COMPONNT CODING & SCHMATIC SYMBOLS S

38 08 ADDD, GFCO, IBMDD & IBMBD, MOD GROUND, GAS AL & GAS AL RLAY TO THIS SHT. BJW UPDATD FORMAT. JHB "NR" "NR" JHB LCTRICAL SCT. III SHT NO. 3B COMPONNT CODING & SCHMATIC SYMBOLS S

39 06 ADDD SMOK DTCTOR. BJW UPDATD FORMAT. JHB "NR" "NR" JHB LCTRICAL SCT. III SHT NO. 3C COMPONNT CODING & SCHMATIC SYMBOLS S

40 - RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID CONDUIT SIZ S KNOCKOUT DIAMTR CONDUIT KNOCK OUT DIAMTR 1/2 7/8 3/4 1 3/ /64 1 1/4 1 23/32 1 1/2 1 31/ /32 2 1/ /8 3 1/2 4 1/ /8 4 1/2 5 1/ /8 6 6 ¾ CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : RKC 2/16/71 RLAS No.: MATRIAL: CONDUIT SIZ S KNOCKOUT DIAMTR PART NO. SHT NO. 4 R. S S-003_4.DOC

41 - ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT 8/14/08 RHM PART NUMBR STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID HYCO PART NUMBR SR-7W-2 DSCRIPTION & COMBINATIONS OF WIRS ACCOMMODATD SIZ AWG. INSULATION NUMBR OF WIRS TYP THICKNSS PR BUSHING (S SHT 7B) 16 4/64 TWO (2) CONDUCTOR AWM PARALLL CORD 1 ON (2) CONDUCTOR 16 4/64 AWM PARALLL CORD 1 (2) SINGL CONDUCTORS /64/WIR 2/64/JACKT ON, (3) CONDUCTOR /64 (4) SINGL CONDUCTORS /64 (4) SINGL CONDUCTORS 2 OR /64 (3) SINGL CONDUCTORS 2 OR SR-7K /64 ON (2) CONDUCTOR AWM PARALLL CORD /64 (3) SINGL CONDUCTORS /64 (2) SINGL CONDUCTORS 2 CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: RDH DAT : 11/14/75 RLAS NO.: PART NO. SHT NO. 5A R. HYCO STRAIN RLIF BUSHING APPLICATION U.L. APPROD S S-003-_5A.doc

42 - ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT 8/14/2008 RHM PART NUMBR STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) HYCO PART NUMBR SR SR-6W-1 NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID DSCRIPTION & COMBINATIONS OF WIRS ACCOMMODATD SIZ AWG. INSULATION NUMBR OF WIRS TYP THICKNSS PR BUSHING (S BLOW) 2/64/WIR 16 2/64/JACKT ON (3) CONDUCTOR 3 4/64 (2) SINGL CONDUCTORS /64 ON (2) CONDUCTOR AWM PARALLL CORD 1 2/64/WIR 2/64/JACKT ON (3) CONDUCTOR /64 (5) SINGL CONDUCTORS /64 (6) SINGL CONDUCTORS /64 (5) SINGL CONDUCTORS /64 (4) SINGL CONDUCTORS /64 (5) SINGL CONDUCTORS TYP SR-5N-4 OR SR-5P /64 (3) SINGL CONDUCTORS /64 (2) SINGL CONDUCTORS 2 1. SPT-3 (2) CONDUCTOR AWM PARALLL CORD (A ). 2. THRMOPLASTIC OR INYL INSULATD. 3. SJT (3) CONDUCTOR CORD (A ). 4. MOTOR LADS WITH NOPRN INSULATION. CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: RDH DAT : 11/14/75 RLAS NO.: HYCO STRAIN RLIF BUSHING APPLICATION U.L. APPROD PART NO. SHT NO. 5B R. S S-003-_5B.doc

43 RHM MANUFACTURING CO. ADD 120, 208, 240, 460, 480 WAS SHT 4A CLT DLTD CAP, (RD DOT) LADS & * FROM PSC. RDH ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDUR 1/24/86 1/25/89 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID MOTOR LAD COLORS SHADD POL 115 OLT 208/230 OLT Single Speed Two Leads Black Black Two Speed Common Lead White Orange High Black Black Low Red Red Three Speed Common Lead White Orange High Black Black Low Red Red Four Speed Common Lead White Orange High Black Black Med. Hi Blue Blue Med. Lo Yellow Yellow Low Red Red PSC 208/230, 240 Single Speed 460, 480 Capacitor Brown Brown Common Lead White Orange Line Black Black Two Speed Capacitor Brown Brown Common Lead White Orange High Black Black Low Red Red Three Speed Capacitor Brown Brown Common Lead White Orange High Black Black Medium Blue Blue Low Red Red CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : RKC 10/11/71 RLAS No.: MATRIAL: MOTOR LAD COLOR STANDARD SINGL PHAS PART NO. SHT NO. 7A R. S S-003_7A.DOC

44 RHM MANUFACTURING CO. ADD 120, 208, 240, 460, 480 WAS SHT 4A CLT DLTD CAP, (RD DOT) LADS & * FROM PSC. RDH ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDUR 1/24/86 1/25/89 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID MOTOR LAD COLORS , 460, 480 Four Speed 115 olt 208/230 olt Capacitor Brown Brown Common Lead White Orange High Black Black Med. Hi Blue Blue Med. Lo Yellow Yellow Low Red Red NOT: MOTOR LADS CANNOT B WHIT WIR WITH COLOR STRIPING. IF COLOR STRIP IS USD, IT MUST HA BAS WIR COLOR OTHR THAN WHIT. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : RKC 10/11/71 RLAS No.: MATRIAL: MOTOR LAD COLOR STANDARD SINGL PHAS PART NO. SHT NO. 7B R. S S-003_7B.DOC

45 2 CHANG NOTIC RLAS NUMBR DSCRIPTION OF LABL MATRIAL S S-004 SHT 3 WIRING DIAGRAM ARA NOTS: 3 DIIDING LIN SCHMATIC DIAGRAM NOT 1 TITL S SHT S-004 SHT 2 1. SCHMATIC DIAGRAM TO B ON SAM SHT AS WIRING DIAGRAM WHN POSSIBL. IF SPAC DOS NOT PRMIT SAM SHT USAG, PLAC ON SPARAT SHT, SAM FORMAT, AND ASSIGN SUBSQUNT SUFFIX NUMBR. 2. SPCIFY SIZ OF DIAGRAM TO GO ON UNIT. 3. LIST ALL COMPONNT CODS ALPHABTICALLY THAT AR USD ON DIAGRAM/SCHMATIC. 4. SHOW COMPONNTS NO POWR TO UNIT. 01 "NR" RISD AND RDRAWN TO SHOW DIAGRAM FROM CAD SYSTM. RDRAWN AND UPDATD TO NW FORMAT. A.F. 1/25/89 JHB "NR" 6/86 RDH/CLT WIRING DIAGRAM / SCHMATIC SHT NO. 8 GNRAL RQUIRMNTS S

46 RHM MANUFACTURING CO. ADD 120, 208, 240, 460, 480 WAS SHT 4A CLT DLTD CAP, (RD DOT) LADS & * FROM PSC. RDH ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2007 PROCDUR 1/24/86 1/25/89 12/5/07 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID MOTOR LAD COLORS SHADD POL 715 OLT 208/230 OLT Single Speed Two Leads Black Black Two Speed Common Lead White Orange High Black Black Low Red Red Three Speed Common Lead White Orange High Black Black Low Red Red Four Speed Common Lead White Orange High Black Black Med. Hi Blue Blue Med. Lo Yellow Yellow Low Red Red PSC 208/230, 240 Single Speed 460, 480 Capacitor Brown Brown Common Lead White Orange Line Black Black Two Speed Capacitor Brown Brown Common Lead White Orange High Black Black Low Red Red Three Speed Capacitor Brown Brown Common Lead White Orange High Black Black Medium Blue Blue Low Red Red CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MD 10/11/71 RLAS No.: MATRIAL: MOTOR LAD COLOR STANDARD SINGL PHAS PART NO. SHT NO. R. S-003 9A 01 S-003_9S.DOC

47 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R 06 ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID SHT DSCRIPTION 1 SCOP 2 IW PRSNTATION 3 TITL BOX 4 MATRIAL 5 RISION INDICATOR 6 WHN CHANGS RQUIR NW DRAWING AND PART NUMBR 7 NOTS 8 PURCHAS PARTS 9 GNRAL INFORMATION 10 DRAFTING SYMBOLS RFRNC XAMPLS CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/14/08 RLAS No.: MATRIAL: DRAWINGS - GNRAL INSTRUCTIONS - INDX PART NO. SHT NO. R. S-004- INDX 06 S-004_INDX.DOC

48 06 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/25/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Drawings Scope This section establishes the practices for use in preparing engineering drawings. Functional/simplified drafting is a technique where drawings are developed with the functional use being the primary driver. Today, more than ever before, the challenge of industry is to produce more and better goods with less effort. The quest is to keep prices competitive so that the company can not only maintain but continue to gain additional market share and profit. This means that the drawing information must be clear and concise, without artistic rendering, unnecessary details, and superfluous (redundant, excessive, needless, extravagant) information. Unnecessary data on drawings adds to the cost of design development, detracts from a design and potentially adds complexity to the interpretation, revision and record retention of the drawing. Functional/simplified drafting was introduced to increase drawing production without losing the fit, form, or function of the depicted design. The idea is to reduce unnecessary information that does not reduce the user's ability to interpret the drawing. High quality drawings are needed by users to perform their work, e.g., procurement, fabrication, and quality inspection. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/25/08 RLAS No.: MATRIAL: DRAWINGS - GNRAL INSTRUCTIONS - SCOP PART NO. SHT NO. 1 R. S S-004_1.DOC

49 06 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/25/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Drawings iews Presentation All drawings that will be released from Research and Development will be completed on an A size (8.5 X 11) sheet format. All drawings shall be produced using the "third angle orthographic projection" system. The third angle system is preferred as the American standard because the views are the same as those obtained by observing the object from the front, top, side, or rear. An isometric view may be utilized on complex drawings for clarification. A minimum number of views, necessary to completely describe the object, shall be used. Sectional views shall be placed as close as practical behind the arrows, showing the shape and construction of the object at the cutting plane. If it becomes necessary to rotate a sectional view, the degree of rotation and direction are specified. A sectional view must be identified by its title consisting of the full word SCTION followed by the pair of letters; for example, SCTION A-A, SCTION B-B, etc. Avoid use of letters I, O, Q, S, X, Y and Z for sectional views. Lettering shall be upper case and bold. Detail views shall be shown in the same plane and in the same arrangement as in the principal view. A detail view must be identified by its title consisting of the full word DTAIL followed by a letter; for example, DTAIL A. Avoid use of letters I, O, Q, S, X, Y and Z for detail views. Lettering shall be upper case and bold. The optional view scale is specified directly below the view. If there is a Section A-A and a view, the view would have a different letter, (iew B-B). Standard text fonts will be utilized on all drawings. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/25/08 RLAS No.: MATRIAL: DRAWINGS - GNRAL INSTRUCTIONS - IW PRSNTATION PART NO. SHT NO. 2 R. S S-004_2.DOC

50 06 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Drawings Title Box Designer and ngineer Approvals Revision Note Material Modeled By and Date Title Revision Original Release Number Sheet Number Part Number CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/25/08 RLAS No.: MATRIAL: DRAWINGS - GNRAL INSTRUCTIONS - TITL BOX PART NO. SHT NO. 3 R. S S-004_3.DOC

51 06 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Drawings Material The drawing material block for sheet metal parts is to have the following information: material thickness, ADS galvanized steel specifications, pre-painted steel or Rheem powder paint specifications, if neither is required, put no paint. If ADS-5008 is used, then put the paint color and texture per sheet 3. See examples below: PR-PAINTD STL PAINTD STL NO PAINT STL The drawing material block for tubing parts is to have the following information: material outside diameter and material make from part number. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/25/08 RLAS No.: MATRIAL: DRAWINGS - GNRAL INSTRUCTIONS - MATRIAL PART NO. SHT NO. 4 R. S S-004_4.DOC

52 06 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Drawings Revision Indicators The revision indicator will be in either the form of: (1) Two digits used on all non-tabulated drawings and specifications. (2) One letter used on tabulated drawings. It should be noted that in all cases all letters of the alphabet can be used with the exception of I and O. On tabulated drawings, the letter indicates a general revision that is common to all parts or assemblies specified. In this case, no change in revision number is indicated in the actual table on the drawing. (3) A combination of: one letter in the title block and corresponding letter with two digits (i.e., a/01) in the table. The letter in the title block indicates a revision to the drawing. The combination of letter and two digits in the table denotes a specific revision to that individual part or assembly designated by a complete part number. The revision number should change only on those individual part numbers that are affected by the revision. Note that whatever digit or letter that is shown in the title block revision number space must also be shown equally in the revision explanation block. Product model index sheets (ADS s) must show a revision number in the title block and a revision number in the column provided on the left side of the sheet next to the item that was revised. Two or more separate sheets with the same complete part number that constitute a complete drawing, such as an assembly or fabricated part, must have the same revision explanation blocks. For example, if there are three sheets under the same complete part number and only one sheet is revised, the other two sheets should show the same revision indicator with a reference in the revision explanation block to the revised sheet, such as no change this sheet, revision number changed to agree with sheet x. xceptions to this rule can be made where inconsistent revision indicators on separate sheets of a drawing would not have an effect on the purpose of the drawing. xamples of this would be: 1) tabulated drawings consisting of numerous individual parts used in various places; 2) ADS- specifications such as rating plate data and production or testing procedures. Locating Revision on the Drawing - When redrawing or revising an original drawing, the actual locations of the revision should be identified by placing revision symbols as close to the change as possible. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/25/08 RLAS No.: MATRIAL: DRAWINGS - GNRAL INSTRUCTIONS - RISION INDICATORS PART NO. SHT NO. 5A R. S S-004_5A.DOC

53 06 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Drawings Revision Indicators The Revision Symbol - A revision symbol is a triangle containing the revision number. NOT: As revisions are removed from the history block, the corresponding revision triangles should be removed also. Revision History Block - The Revision History block is intended for recording and organizing textual descriptions of the revisions being made to the drawing. It will include the revision number, a description of the change(s), initial of the change, the date of the revision, and the change notice release number. Description of Change Change Notice Number Revision Number qual to Title Box Revision Changed by Initials Date of Change Minor Changes - When minor changes such as correction of misspelled words are required, the revision block will be designated with a dash ( ) and noted as corrected spelling, no change to part and released on change notice. Parts Redrawn Without Changes - The replacement drawing must duplicate the exact requirements and specifications of the original. Put your name and the original release date in the MODLD_BY and DAT_MODLD parameters and the original change notice number from the part that is being redrawn. Place a in the revision and RDRAWN ON PRO/ NO CHANG TO PART in the description of the Revision History box along with the initials of the individual redrawing the part, the date of the redraw, and change notice release number. Be sure to include the last revision shown from the part being redrawn and the correct revision triangles (if applicable). CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/25/08 RLAS No.: MATRIAL: DRAWINGS - GNRAL INSTRUCTIONS - RISION INDICATORS PART NO. SHT NO. 5B R. S S-004_5B.DOC

54 06 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Drawings When Changes Require New Drawing and Part Number When considering a change to a drawing of an existing part or assembly, the following criteria should be applied to determine whether an existing drawing can be modified or a new drawing must be prepared and assigned a new drawing identity. On an existing detail or assembly drawing that can be tabulated, the same consideration would apply regarding assignment of a new part, group, or dash suffix. A new drawing must be prepared when performance or durability is affected to such an extent that items must be superseded for reasons of safety or malfunction. A new drawing must be prepared when parts, subassemblies, or complete articles are changed to such an extent that the superseding items are not interchangeable with previous items. A new drawing must be prepared when replaced items are limited to use in specific articles or models while the superseding parts are not limited. A new drawing must be prepared when changes affect interchangeable, repairable assemblies that contain noninterchangeable parts. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/25/08 RLAS No.: DRAWINGS - GNRAL INSTRUCTIONS - WHN CHANGS RQUIR NW DRAWING AND PART NUMBR MATRIAL: PART NO. SHT NO. 6 R. S S-004_6.DOC

55 06 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Drawings Notes Notes are used on drawings to supply information that cannot be presented in any other descriptive way. Notes are used for such an infinite variety of purposes that it is not practical to establish standard notes for every condition. A standard method of applying, placing, and revising notes on the engineering drawings should be used to maintain reasonable company-wide uniformity. All Sheetmetal parts and assemblies must contain the following dimensioning note: CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/25/08 RLAS No.: MATRIAL: DRAWINGS - GNRAL INSTRUCTIONS - NOTS PART NO. SHT NO. 7 R. S S-004_7.DOC

56 06 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Drawings Purchase Parts Drawing must include all required information to ensure appropriate item is ordered, including vendor and part number if essential. Bulk item drawing must include unit of measure and formula for calculating unit of measure for the bills of material. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/25/08 RLAS No.: MATRIAL: DRAWINGS - GNRAL INSTRUCTIONS - PURCHAS PARTS PART NO. SHT NO. 8 R. S S-004_8.DOC

57 03 RHM MANUFACTURING CO. RDRAWN ADDD HOLS, TUBING AND RFRNC DATA JWN 04 ADDD SHARP DGS/BURRS TST RFRNC JWN 05 ADDD WHIT RUST NOT. MJM RSARCH & DLOPMNT DPARTMNT Y-0486S Y-0528S ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID 8/14/2008 STANDARD TOLRANC DSCRIPTION UNLSS OTHRWIS SPCIFID FRACTIONAL ± 1/32 ANGULAR +1-3 HOLD DIMNSIONS ± 1/64 DCIMAL ±.030 PACKAGING COMPONNTS SCRW GRAB HOLS (GNRALLY DCIMAL) SCRW CLARANC HOLS (GNRALLY FRACTIONAL) PHYSICAL DIMNSIONS: +1/8-1/16 PRINTING SIZ: ± 1/8 PRINTING LOCATION: ± 1/ ±.030 OTHR GNRAL HOLS ±.030 TUBING HOLS LINAR ±.250 ANGULAR ± 5 RFRNC DIMNSIONS RF. OR ( ) TUBING DIMNSIONS ±.060 SHARP DGS/BURRS (WHN CALLD OUT) TST USING SHARP DG TST QUIPMNT THAT CONFORMS TO UL 1439 UNACCPTABL WHIT RUST: WHIT RUST ON UNPAINTD PARTS THAT WOULD NOT NORMALLY B XPOSD TO OUTDOOR CONDITIONS IS NOT ACCPTABL. PARTS SIMILAR TO CONTROL PANLS, CONTROL BOXS AND BLOWR ASSMBLIS AR SOM XAMPLS. WHIT RUST ON TH XTRIOR SURFAC OF A PAINTD PART THAT WOULD B ASTHTICALLY UNACCPTABL TO TH FINAL CUSTOMR. WHIT RUST ON TH XTRIOR SURFAC OF PARTS RQUIRING PAINT APPLICATION OPRATIONS THAT WOULD PRNT TH PAINT FROM ADHRING. WHIT RUST CONDITIONS THAT WOULD INHIBIT COMPLTION OF DOWNSTRAM MACHIN OPRATIONS. CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: DAT : 8/25/08 RLAS NO.: DRAWINGS GNRAL INSTRUCTIONS - GNRAL INFORMATION PART NO. SHT NO. 9 R. S S-004_9.DOC

58 06 RHM MANUFACTURING CO. ADDD TO WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/14/2008 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID SYMBOL OR DFINITION PLACD AROUND A CHARACTRISTIC TO INDICAT THAT IT MUST B A CONTROL CHARACTRISTIC. THAT IS, A DIATION FROM SPCIFICATION COULD POSSIBLY RSULT IN DAMAG TO TH PRODUCT, LSS THAN A SAF OPRATING CONDITION, NON-COMPLIANC WITH UNITARY RGULATIONS, AN UNRASONABL NUMBR OF FILD SRIC CALLS, SIGNIFICANT CUSTOMR DISSATISFACTION OR HIGH INTRNAL COST. IDNTIFID BY A CIRCL M SYMBOL NAR TH CHARACTRISTIC. A CHARACTRISTIC IS DFIND AS MINOR WHN A DIATION FROM SPCIFICATION COULD RSULT IN: A PRODUCT FALLING SHORT OF ITS INTNDD FUNCTION AN UNRASONABL NUMBR OF SRIC CALLS. SIGNIFICANT CUSTOMR DISSATISFACTION A MINOR CLASSIFICATION RQUIRS A CONTROL PLAN FOR CHCKING ON A RGULAR BASIS, BUT DOS NOT RQUIR STATISTICAL CONTROL DATA. * S NOT RISION TO DIMNSION, ANGL MASURMNT, NOT, TC. RF. OR ( ) PLACD AROUND A DIMNSION RFRNC DIMNSION. BY DFINITION, A RFRNC DIMNSION IS A DIMNSION WITHOUT TOLRANC, USD FOR TOOLING PURPOSS ONLY, AND DOS NOT GORN MACHINING OR Q.A. INSPCTION OPRATIONS AFTR FIRST PART APPROAL. RFRNC DIMNSIONS SHOULD B HLD TO NGINRING SPCIFICATIONS FOR NW AND RISD TOOLING AND AR NOT RQUIRD TO B MASURD BY Q.A. AFTR FIRST PART APPROAL IS RCID. CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: DAT : 8/25/08 RLAS NO.: MATRIAL: DRAWINGS GNRAL INSTRUCTIONS DRAFTING SYMBOLS PART NO. SHT NO. 10 R. S S- 004_10.doc_10.DOC

59 01 RHM MANUFACTURING CO. ADDD WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 02 ADDD SHT 3. ZJW 8/28/2008 Y-0528S003 08/05/2010 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID SHT DSCRIPTION 1 SCOP 2 SHT MTAL GUIDLINS 3 MATRIAL BND ALLOWANC CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/14/08 RLAS No.: MATRIAL: SHT MTAL - INDX PART NO. SHT NO. R. S-006- INDX 02 S-006_INDX.DOC

60 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R 01 ADDD WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/28/2008 STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Sheet Metal Scope This section contains specific information related to the documentation and specification practices for sheet metal. The practices defined herein are limited to those of a general nature since local practice is affected so heavily by sheet metal equipment availability such as bending brakes, presses, numerical controlled machines, and forming dies and punches. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/14/08 RLAS No.: MATRIAL: SHT MTAL - SCOP PART NO. SHT NO. 1 R. S S-006_1.DOC

61 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R 01 ADDD WORD FORMAT UPDATD IN ACCORDANC WITH 2008 PROCDURS 8/28/2008 STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Sheet Metal General Rules Only truly critical dimensions should be highlighted as such. Placing excessively high tolerances and redundant dimensions can dramatically increase the cost of a part. When a bend is made too close to a hole, the hole may become deformed. It is recommended that the edge of a hole be no closer to the tangent of the bend than 3 times the material thickness. The distance from the edge of a hole to the edge of the material should be at least two times the material thickness. The minimum height of a flange is two and a half times the material thickness without requiring additional operations. The standard inside bend radius is the material thickness. Where practicable, the finished part should be defined without specifying the manufacturing method. Thus, only the diameter of a hole is given without specifying how it is to be produced. Features should not be dimensioned from a raw edge if possible. Flanges should be run-out when possible and should be shown as reference ( ) dimensions. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/14/08 RLAS No.: MATRIAL: SHT MTAL GNRAL GUIDLINS PART NO. SHT NO. 2 R. S S-006_2.DOC

62

63

64

65 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID SHT NUMBR DSCRIPTION 1 NAMING OF WORD PROCSSING OR SPRADSHT DRAWING FILS 2 A- / AS- 3 PURCHAS PARTS 4 ADS- 5 COMPRSSOR CODS 6 ILLUSTRATIONS 7 QA- 8 OPTION CODS 9 SQUNC NUMBR 10 WIRS / WIR ID LIST S S-002 S S-013 S S-014 CHANG NOTIC DIATION NGINRING CHANG RQUST CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MCB RLAS No.: MATRIAL: NUMBR ASSIGNMNT AND NAMING CONNTION PART NO. SHT NO. INDX R. S S-007_INDX.DOC

66 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID When creating a multiple sheet drawing in a word processing or spreadsheet file, a determination about the revisions must be made. If each sheet in the drawing can have different revisions, then each sheet must be an individual file. However, if all sheets will be kept at the same revision then all sheets should be in the same file. When naming these files make sure to use all lower case letters for both the body of the file name and the file name extension. See example below for naming individual sheet files of multiple sheet drawings. Drawing number Sheet No. ads j _ a1.doc Drawing number Sheet No. ads _ a1.xls CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MCB RLAS No.: NAMING OF WORD PROCSSING OR SPRADSHT DRAWING FILS MATRIAL: PART NO. SHT NO. 1 R. S S-007_1.DOC

67 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID 1.0 A- / AS- New Part Number Assignment 1.1 Go to O:\New Part Number Assignment folder and open Part Number Assignment Sheet.xls and take out the next available number. 1.2 When assigning Tabulation Drawings go to O:\New Part Number Assignment folder open the TAB sub folder and open the _TABSH.XLT and follow the instructions contained within the file. 1.3 To assign part number to existing tabulation, go to O:\New Part Number Assignment folder open the TAB sub folder. Search for existing part number tabulation assignment file. Open file and add part number. 2.0 A- / AS- Old Tabulation Part Number Assignment 2.1 Go to O:\Old Part Number Assignment folder and open A_AS sub folder open the TAB s2ub folder and search for existing part number tabulation assignment file. Open file and add part number. If part number doesn t exist then create a tabulation sheet. Open _TABSH.XLT and follow the instructions contained within the file. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MB RLAS No.: MATRIAL: NUMBR ASSIGNMNT - A/AS - PARTS PART NO. SHT NO. 2 R. S S-007_2.DOC

68 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID 1.0 Purchased Parts New Part Number Assignment 1.1 Go to O:\New Part Number Assignment folder and open Part Number Assignment Sheet.xls and take out the next available number. 1.2 When assigning Tabulation Drawings go to O:\New Part Number Assignment folder open the TAB sub folder and open the _TABSH.XLT and follow the instructions contained within the file. 1.3 To assign part number to existing tabulation, go to O:\New Part Number Assignment folder open the TAB sub folder. Search for existing part number tabulation assignment file. Open file and add part number. 2.0 Purchased Parts Old Tabulation Part Number Assignment 2.1 Go to O:\Old Part Number Assignment folder and open PP sub folder open the TAB sub folder and search for existing part number tabulation assignment file. Open file and add part number. If part number doesn t exist then create a tabulation sheet. Open _TABSH.XLT and follow the instructions contained within the file. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MB RLAS No.: MATRIAL: NUMBR ASSIGNMNT - PUCHAS PARTS PART NO. SHT NO. 3A R. S S-007_3A.DOC

69 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID PRFIX COMMODITY DSCRIPTION 01 STL 02 ALUMINUM 03 SHT COPPR 04 PLASTIC RSIN FORMD SHT MTAL PARTS CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MCB RLAS No.: MATRIAL: NUMRICAL INDX TO COMMODITY PRFIX FOR MATRIAL CONTROL PART NUMBRS PART NO. SHT NO. 3B R. S-007-3B- 00 S-007_3B.DOC

70 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID PRFIX COMMODITY DSCRIPTION WATR PUMPS WALL THRMOSTATS & HUMIDISTAT HUMIDIFIR 42 RLAYS CONTACTORS SWITCHS PRIMARY CONTROL CIRCUIT BRAKRS 43 CAPACITORS 44 RSISTORS HATING LMNTS FUSS 45 TRMINAL FITTINGS TRMINAL BLOCKS MARKRS WIR INSULATORS STRAIN RLIF JUNCTION BOXS CONDUIT CONDUIT FITTINGS PLUG BUTTONS 46 TRANSFORMRS 47 PRSSUR & TMPRATUR CONTROLS FAN & LIMIT DFROST CONTROLS SPD CONTROLS POWR PACK POTNTIOMTR 48 (ASSIGND TO NATIONAL HATR ST. PAUL) 49 GAUGS OIL, GAS, AIR OR RFRIGRANT PRSSURS 50 (ASSIGND TO NATIONAL HATR ST. PAUL) CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MCB RLAS No.: NUMRICAL INDX TO COMMODITY PRFIX FOR MATRIAL CONTROL PART NUMBRS MATRIAL: PART NO. SHT NO. 3C R. S S-007_3C.DOC

71 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID PRFIX COMMODITY DSCRIPTION 51 MOTORS 52 PAINTS SOLNTS RFRIGRANT COSMOLIN UNDRCOATING INK NITROGN ANTIFRZ 53 NAMLING 54 AIR FILTRS COLLCTOR CLLS & ACCSSORIS 55 COMPRSSORS & PUMPS 56 COMPRSSOR MOUNTS, GROMMTS, RUBBR PARTS (XCPT GASKTS) 57 WLDING SOLDR BRAZING MATRIALS FLUX 58 DRAFT RGULATORS, DAMPRS, DAMPR OPRATOR, NT FITTINGS & CAPS 59 OIL BURNRS & PARTS 60 COMBINATION GAS ALS 61 ALS SOLNOID FLOAT MANUAL XPANSION CHCK BICYCL RRSING AL COR RGULATORS 62 ORIFICS SPRAY NOZZLS PILOTS IGNITRS THRMOCOUPL 63 FASTNRS THRADD CHAIN RIT WASHRS CLIPS TINNRMAN BUSHINGS 64 FASTNRS OTHR CLAMPS LCTRICAL STO WIR - STRAPS KNOBS HINGS LATCHS HANGRS CABL 65 COILS APORATOR & CONDNSR 66 SPRINGS 67 ADHSIS GLUS CMNTS PIP COMPOUND PRMA-GUM INSULATION GASKTS FLT ASBSTOS TAP SALR PLASTIC TUBING PLXIGLAS PLASTIC PARTS 70 BLOWR SHAFT WHL FANS SCROLLS MOUNTING BRACKTS BARINGS 71 BLTS PULLYS SHAS THRUST COLLARS & WASHRS CASTINGS BURNR CASTS & STL CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MCB RLAS No.: NUMRICAL INDX TO COMMODITY PRFIX FOR MATRIAL CONTROL PART NUMBRS MATRIAL: PART NO. SHT NO. 3D R. S S-007_3D.DOC

72 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID PRFIX COMMODITY DSCRIPTION 76 TUB HAT XCHANGR FLU GAS TRANSFR TUB ASSMBLY 77 HAT SINK HOS - HOS FITTINGS 80 TUB - PIP COPPR - ALUMINUM TUBING COIL 81 PIP FITTINGS - MANIFOLDS CLAMPS 82 TUB FITTINGS - HADRS - CLAMPS RFRIGRANT FILTRS STRAINRS DISTRIBUTORS ACCUMULATORS DRIRS RFRIGRANT FITTINGS 90 WIRING DIAGRAMS WIRING DIAGRAM LABLS 91 NAMPLAT RATING PLATS TAGS LABLS INSTRUCTIONS WARRANTIS BUSINSS CARDS BOOKLTS PRINTD MATRIAL 94 RODS THRADD RODS ANGL IRON CHANNL IRON KY STOCK FLAT STOCK CHAIN JACK 95 PRFORATD XPANDD MTALS SCRNS LOURS GRILLS GRILL CAP WRITTN OFF OBSOLT INNTORY 99 CRATS CARTONS BAGS PACKAGING MATRIAL NLOPS - TAP CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MCB RLAS No.: NUMRICAL INDX TO COMMODITY PRFIX FOR MATRIAL CONTROL PART NUMBRS MATRIAL: PART NO. SHT NO. 3 R. S S-007_3.DOC

73 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID COMMODITY DSCRIPTION PRFIX COMMODITY DSCRIPTION PRFIX A AL 61 BLOWR ASSMBLY 70 ADAPTR (TUB FITTING) 82 BLOWR PARTS 70 ADHSI (ALL TYPS) 67 BLOWR RPM CHART 92 AIR FILTRS 54 BLOWR SAL 68 AIR FLOW S. PRSSUR DROP CHART 92 BLOWR SHAFT, WHL 70 ALUMINUM PRMANNT 54 BODY FLANGS (AL) 61 ANGL (STRUCTURAL) 94 BOLT CARRIAG 63 ANTIFRZ 52 BRACKT AL 61 APPLIANC RLAY 42 BUSHING 56 ASBSTOS (ALL MATRIALS) 68 BUSHING NYLON SNAP 45 BUSHING STRAIN RLIF 45 AUTO-SAFTY PILOT 62 BUSHING UNIRSAL 45 AUXILIARY LIMIT CONTROL 47 BURNR BLD CLIP ASSMBLY 62 BAGS 99 BURNR CASTINGS 75 BAS PAN (FORMD SHT MTAL) 10 BURNR STL 75 B AL 61 BARING BALL 70 BIMTAL THRMAL DLAY 42 CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: MCB DAT : RLAS NO.: ALPHABTICAL INDX TO COMMODITY PRFIX FOR MATRIAL CONTROL NUMBRS PART NO. SHT NO. 3F R. S S-007_3F.DOC

74 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID COMMODITY DSCRIPTION PRFIX COMMODITY DSCRIPTION PRFIX CABL 64 COIL SPRING TUB BNDR 82 COMBINATION FAN & LIMIT CONTROL 47 CABINT LATCH 64 COMBINATION GAS AL 60 CAP FAN MOTOR 70 COMPRSSOR 55 CAPACITORS 43 CONDNSR COIL 65 CAPILLARY TUBING 80 CONDUIT, CONDUIT FITTING 45 CASTINGS 75 CONNCTOR BOX STRAIGHT SQUZ TYP 45 CARTON 99 CONNCTOR BOX 90 SQUZ TYP 45 CONNCTOR SPLIT-RING TYP 45 CLL COLLCTOR PACKAG 54 CLL COMBINATION COLLCTOR & IONIZR 54 CONTACTOR 42 CLL WASHING CONTAINR 54 CLL WASHING KIT 54 CONTROL BOX (FORMD SHT MTAL) 10 CRTIFICATION LABL 92 CONTROL CNTRS 41 CHANG OR RLAY 42 CONTROL PANL 47 CHANNLS (STRUCTURAL) 94 CHARG CHART 92 CONTROL TRANSFORMR 46 CHCK AL MAGNTIC TYP 61 COPPR GASKT FLAR 68 CHOK 59 COPPR WIR CLOTH 95 CIRCUIT BOARD 47 COSMOLIN 52 CIRCUIT BRAKRS 42 COUPLING (LCTRICAL) 45 CLAMP LCTRICAL 64 COUPLING (TUB) 83 CLAMP MCHANICAL 81 CRAT 99 CLOGGD FILTR INDICATOR 41 CUSHION NOPRN 56 CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: MCB DAT : RLAS NO.: ALPHABTICAL INDX TO COMMODITY PRFIX FOR MATRIAL CONTROL NUMBRS PART NO. SHT NO. 3G R. S S-007_3G.DOC

75 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID COMMODITY DSCRIPTION PRFIX COMMODITY DSCRIPTION PRFIX DCAL 92 LBOW TUB 82 DFROST CONTROL 47 LBOWS PIP 81 DLAAN OIL BURNR NOZZL 59 LCTRIC HATING RLAY 42 DRATING PLAT 91 LCTRICAL IDNTIFICATION TAG 92 DIRCTION LABL 92 NAMLING 53 DISTRIBUTOR 83 NTRAINMNT SPARATOR 95 DRAFT CONTROL 58 POXY GLU 67 DAMPR OPRATOR/DAMPR ASSMBLY` 58 APORATOR COIL 65 DRAWR ASSMBLY 59 XPANDD MTAL 95 DUST COR 99 XTNSION 58 DUST FILTR 54 XTNSION SPRING 66 YLT TRMINAL (LCTRICAL) 45 NLOPS 99 CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: MCB DAT : RLAS NO.: ALPHABTICAL INDX TO COMMODITY PRFIX FOR MATRIAL CONTROL NUMBRS PART NO. SHT NO. 3H R. S S-007_3H.DOC

76 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID COMMODITY DSCRIPTION PRFIX COMMODITY DSCRIPTION PRFIX FAN BLAD 70 FUS 44 FAN CONTROL 47 GAS MANIFOLD CONTROL 60 FAN CONTROL SWITCH 47 GALANIZD WIR CLOTH 95 FAN GUARD 70 FAN MOUNT 70 GAS AL & PILOT STAT 61 FAN TIMR 47 GASKT 68 FASTNRS 63 GASKT FAN & LIMIT 68 FLT, FLT SAL 68 GAUGS 49 FIBR GLASS INSULATION 68 FIBR GLASS PAD, STRIP 68 GNRAL INFORMATION 92 FILTR DRIR 83 GNRAL PURPOS SHUNT RLAY 42 FISH PAPR 68 GLASS FIBR TAP 99 FILTRS 54 GRILL 95 FITTINGS HOS 79 GROMMT 56 FLAM DTCTOR 42 GROO PIN 63 FLAR CAP, FLAR NUT 83 FLAR SAL CAP 83 FLOAT AL ASSMBLY 61 FLU PIP OAL 58 FLU PIP ROUND 58 FLUX 57 CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: MCB DAT : RLAS NO.: ALPHABTICAL INDX TO COMMODITY PRFIX FOR MATRIAL CONTROL NUMBRS PART NO. SHT NO. 3J R. S S-007_3J.DOC

77 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID COMMODITY DSCRIPTION PRFIX COMMODITY DSCRIPTION PRFIX HANDL 64 JUMPR TRMINAL BOARD 45 HANGR MOUNT 70 JUNCTION BOXS 45 HADR 82 KIMPACK PAD 68 HATING LMNT 44 KNOB 64 HIGH PRSSUR CONTROL OIL BURNR ATOMIZING 59 KWIK SNSOR RLAY 42 HOS 70 LABLS 92 HOS CLAMP 79 LL HANDL PLUG TYP 61 HUMIDIFIRS 81 LIMIT CONTROL 47 HUMIDIFIR CONTROL 41 LINT SCRN 54 HUMIDIFIR PACKAG 41 HUMIDSTAT 41 IGNITR PILOT 62 INSTALLATION OF SAFTY LBOW 92 INSTRUCTION CARD 92 INSTRUCTION PLAT 91 INSULATION ALL TYPS 68 INK 52 CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: MCB DAT : RLAS NO.: ALPHABTICAL INDX TO COMMODITY PRFIX FOR MATRIAL CONTROL NUMBRS PART NO. SHT NO. 3K R. S S-007_3K.DOC

78 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID COMMODITY DSCRIPTION PRFIX COMMODITY DSCRIPTION PRFIX MANIFOLD 81 NAMPLAT 91 MANILA NLOP 99 NOPRN HOS 79 MANUAL OPNR 61 NIPPL 80 MANUAL RST THRMAL PROTCTOR 42 NIPPL CONDUIT FITTING 45 MARKR STRIP 45 NITROGN 52 MTR SYSTM PRFORMANC 41 NOMNCLATUR CARD 92 MICROLIT INSULATION WOOL 68 NUT (FOR PIP THRAD) 81 MICROTMP 44 NUT 63 MODULATING GAS AL 60 NYLON STRAP 45 MOISTUR & LIQUID INDICATOR 83 OIL BURNRS & PARTS 59 MOTORS 51 OPRATING INSTRUCTIONS 92 MOTOR BRACKT 70 ORIFIC PLUG 62 MOTOR MOUNT 70 ORIFIC SPUD 62 MOUNTING AR 70 ORLOAD RLAY 42 MOUNTING FLANG (Q.C.) 83 OWNRS GUID 92 OWNRS GUID & RPAIR PARTS 92 OWNRS GUID & WARRANTY BOOK 92 CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: MCB DAT : RLAS NO.: ALPHABTICAL INDX TO COMMODITY PRFIX FOR MATRIAL CONTROL NUMBRS PART NO. SHT NO. 3L R. S S-007_3L.DOC

79 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID COMMODITY DSCRIPTION PRFIX COMMODITY DSCRIPTION PRFIX PACKING LIST 92 PRSSUR RLIF AL 47 PAPR BAG 99 PRIMARY CONTROL 42 PAINT 52 POWR PACK 47 PAST (FLUX) 57 PULL HANDL 64 PRMA-GUM 67 PULLY 71 PRMANNT FILTR 54 PUMP HOS (DISCHARG) 56 PIGGY BACK TRMINAL 45 PURG BLOWR 70 PILOT BURNR, FILTR, ORIFIC 62 QUICK CONNCT (TUBING) 83 PILOT PRSSUR RGULATOR 60 QUICK CONNCT (LCTRICAL) 45 PILOTSTAT 62 RLAYS 42 PLASTIC PARTS 68 RATING PLAT 92 PLASTIC TUBING 68 RFRIGRANT 52 PLNUM INSTRUCTIONS 92 RGULATOR, GAS AL 61 PLXIGLAS 68 PLUG BUTTON 45 RSISTOR 44 PLUG IN RLAY 42 RTAINR CLIPS 59 PLUNGR BOARD ASSMBLY 45 RRSING AL, ROTOLOCK AL 61 POTNTIAL RLAY 42 POTNTIOMTR 47 ROD HANGR 64 POWR PIL THRMOPIL 62 POWR SUPPLY 42 RUBBR BUMPR, RUBBR TIP 56 PRSSUR CONTROL HIGH SID, LOW SID 47 RUBBR TUBING 79 CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: MCB DAT : RLAS NO.: ALPHABTICAL INDX TO COMMODITY PRFIX FOR MATRIAL CONTROL NUMBRS PART NO. SHT NO. 3M R. S S-007_3M.DOC

80 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID COMMODITY DSCRIPTION PRFIX COMMODITY DSCRIPTION PRFIX SAFTY CHAIN (JACK) 94 START WIND PROTCTOR 42 SCRN 95 STL BURNRS 75 SCRW DRIR 63 STL SHAFT 71 SCRW (MACHIN, SHT MTAL, WLD) 63 STP OPNING PRSSUR RGULATOR 60 SCROLL SID 70 STITCHING WIR 99 ST SCRW CONNCTORS 45 STOPPR RUBBR 56 SQUNCR CONTROL 47 STRAIGHT FITTING 82 SHA 71 STRAIGHT ON FITTING 45 SHIPPING SUPPORTS 99 STRAIN RLIF ADAPTR, FITTINGS 45 SHUT-OFF AL 61 STRAINR 83 SOLDR (SILR, TUB, WIR) 57 STRAPPING KIT 64 SOLNOID AL COIL 61 STRIPPING, POLYURTHAN 56 SOLID STAT SPD CONTROL 47 STRIPPING, RUBBR 56 SOLNTS 52 SUCTION FILTR DRIR 61 SPRAY NOZZL 62 SWITCHS 42 SPRING AIR SHUTTR 66 SPRING CATCH 66 SPRING DAMPR ADJ 66 STAPLS 99 START RLAY 42 CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: MCB DAT : RLAS NO.: ALPHABTICAL INDX TO COMMODITY PRFIX FOR MATRIAL CONTROL NUMBRS PART NO. SHT NO. 3N R. S S-007_3N.DOC

81 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID COMMODITY DSCRIPTION PRFIX COMMODITY DSCRIPTION PRFIX TAB TRMINAL 45 TUB CLAMPS 82 TAP 99 TUB NOPRN OR RUBBR 79 TAP SALR 68 TUB PLASTIC 68 T TUB 82 TUBING (STL ALUMINUM COPPR) 80 T PIP 81 TWO STAG PUMP 59 TRMINAL BLOCK (STRIP) 45 UNDRCOATING 52 TRMINAL FLAG (LCTRIC) 45 UNION INSULATOR BUSHING 45 TRMINAL PROTCTOR 56 UNITORQU LOCKNUT 63 TRMINAL SPAD 45 BLT 71 THRMOCOUPL 62 AL BODY 61 THRMODISC LIMIT CONTROL 47 AL CHARG 61 THRMOSTATS 41 AL COR 61 THRUST COLLAR 70 AL XPANSION 61 TIM DLAY RLAY 42 AL SOLNOID 61 TIMR 47 AL (THRMO-AL) 61 TINNRMAN CLIPS 63 NT HOODS 58 TRANSFORMR 46 TRI-ARM (BARING MOUNT) 70 TRIM 91 CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: MCB DAT : RLAS NO.: ALPHABTICAL INDX TO COMMODITY PRFIX FOR MATRIAL CONTROL NUMBRS PART NO. SHT NO. 3P R. S S-007_3P.DOC

82 HM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT R STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID COMMODITY DSCRIPTION PRFIX COMMODITY DSCRIPTION PRFIX WARRANTY 92 WOOD PRODUCTS 99 WARRANTY RGISTRATION CARD 92 WON ASBSTOS TAP 68 WARNING TAG 92 WROUGHT CAP 82 WARP SWITCH TRANSFORMR 46 WROUGHT RDUCING COUPLING 82 WASHRS 63 WATR PANL HUMIDIFIR 68 WATR PUMP 55 WAXD PAPR 99 WLDING / BRAZING FLUX 57 WLDING ROD & WIR 57 WIR 45 WIR INSULATION 68 WIR JOINT 45 WIR LABL 92 WIR MARKRS 45 WIR NUT 45 WIRING DIAGRAM 90 CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: MCB DAT : RLAS NO.: ALPHABTICAL INDX TO COMMODITY PRFIX FOR MATRIAL CONTROL NUMBRS PART NO. SHT NO. 3Q R. S S-007_3Q.DOC

83 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID 1.0 ADS New Part Number Assignment 1.1 Go to O:\New Part Number Assignment folder and open Part Number Assignment Sheet.xls and take out the next available number. 1.2 When assigning Tabulation Drawings go to O:\New Part Number Assignment folder open the TAB sub folder and open the _TABSH.XLT and follow the instructions contained within the file. 1.3 To assign part number to existing tabulation, go to O:\New Part Number Assignment folder open the TAB sub folder. Search for existing part number tabulation assignment file. Open file and add part number. 2.0 ADS Old Tabulation Part Number Assignment 2.1 Go to O:\Old Part Number Assignment folder and open ADS sub folder open the TAB sub folder and search for existing part number tabulation assignment file. Open file and add part number. If part number doesn t exist then create a tabulation sheet. Open _TABSH.XLT and follow the instructions contained within the file. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MB RLAS No.: MATRIAL: NUMBR ASSIGNMNT - ADS PART NO. SHT NO. 4 R. S S-007_4.DOC

84 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Compressor Codes will no longer be assigned on the Compressor Assembly sheet. A Compressor Code assignment sheet has been set up. This sheet can be found at O:\New Part Number Assignment\COMPCOD.DOC or click on the hyperlink to go straight to the file. Once you have filled out all of the fields on the assignment sheet go to the appropriate Compressor Assembly drawing and add your Compressor Code, Model number, Compressor part number, endor, Initials and the date. All Compressor Code sheets have been placed in the Data Management Software System. If the compressor code you have assigned needs to be added to an existing drawing, check the drawing out. If you need to create a new Compressor Assembly sheet, a template file has been created, compcode.dot. Go into Word and click File, New, click on My Computer, then select Drwg Bdr tab and select compcode.dot template file. The naming convention for the Compressor Assembly sheet should be AS- XXXXX -.doc. The XXXXX in the file name should be the first Compressor Code on that particular sheet. Import the file into the Data Management Software System, (refer to DDS-?? for Importing Non-Cad Documents). Under no circumstances should anyone copy or recreate any file that is stored in the Data Management Software System. If you are unable to update a file, ask for assistance. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MCB RLAS No.: MATRIAL: COMPRSSOR COD PART NUMBR ASSIGNMNT PART NO. SHT NO. 5 R. S S-007_5.DOC

85 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID 1.0 Illustration Part Number Assignment 1.1 Go to O:\Old Part Number Assignment folder and open Illustrations sub folder and open Illustration Part Number Assignment.xls and take out the next available number. 1.2 When assigning Tabulation Drawings go to O:\Old Part Number Assignment folder open the TAB sub folder and open the _TABSH.XLT and follow the instructions contained within the file. 1.3 To assign part number to existing tabulation, go to O:\Old Part Number Assignment folder open the Illustrations sub folder open the TAB sub folder. Search for existing part number tabulation assignment file. Open file and add part number. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MB RLAS No.: MATRIAL: NUMBR ASSIGNMNT - ILLUSTRATIONS PART NO. SHT NO. 6 R. S S-007_6.DOC

86 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID 1.0 QA New Part Number Assignment 1.1 QA part numbers are assigned by Design Service Manager only. This sheet can be found at O:\New Part Number assignment\qa\qaindx.doc or click on the hyperlink to go straight to the file. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MB RLAS No.: MATRIAL: NUMBR ASSIGNMNTS - QA- PART NO. SHT NO. 7 R. S S-007_7.DOC

87 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID 1.0 OPTION-COD NUMBR ASSIGNMNT (NON-COMMRCIAL) 1.1 The option code number system for all products is required to insure that all components, purchased or fabricated, specified in the Bill of Material are identifiable by the accounting dept. for cost purposes, and by the marketing and production depts. for order entry and production scheduling. 1.2 Any option or combination of options to a product must be assigned a code number. 1.3 The index pages ADS direct you to the proper numbers to be used for any given product, and the data should be filled in by the number to indicate what models are covered by the option number. 1.4 The ADS-51??-?? sheet 1 should be updated with options that apply for that specific model. 2.0 OPTION-COD NUMBR ASSIGNMNT (COMMRCIAL) 2.0 The option code number system for all products is required to insure that all components, purchased or fabricated, specified in the Bill of Material are identifiable by the accounting dept. for cost purposes, and by the marketing and production depts. for order entry and production scheduling. 2.1 The index pages ADS direct you to the proper numbers to be used for any given product. 2.2 The ADS-51??-?? sheet 1 should be updated with options that apply for that specific model. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MB RLAS No.: MATRIAL: NUMBR ASSIGNMNT - OPTION CODS PART NO. SHT NO. 8 R. S S-007_8.DOC

88 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID 1.0 Sequence Number Assignment 1.1 To assign a sequence number to a part number first make sure it doesn t already exist. Check the MS system and do a where used on the part number. If it is a new part check for a similar part to see if it already has a sequence number assigned. i.e. All Cabinets are at sequence number Sequence numbers are assigned by a Design Service Designee. To view Sequence number assignment sheet click on hyper link below. (L:\Company Resources\R&D\Standards\sequence_nos_assign.doc) CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MB RLAS No.: NUMBR ASSIGNMNT - SQUNC NUMBR MATRIAL: PART NO. SHT NO. 9 R. S S-007_9.DOC

89 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID 1.0 Wires - New Part Number Assignment 1.1 Go to O:\New Part Number Assignment folder and open Part Number Assignment Sheet.xls and take out the next available number. 2.0 Wires - Old Tabulation Part Number Assignment 2.1 Tabulation numbers are assigned on the wire drawing itself. 3.0 Wire ID Assignment 3.1 Wire ID numbers are assigned by Design Service Manager only. This sheet can be found at O:\New Part Number assignment\wire ID\WIR ID.xls or click on the hyperlink to go straight to the file. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MB RLAS No.: MATRIAL: NUMBR ASSIGNMNT - WIR / WIR I.D. PART NO. SHT NO. 10 R. S S-007_10.DOC

90 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID SHT DSCRIPTION 1 SCOP 2 DIMNSIONING GUIDLINS 3 TOLRANCING GUIDLINS CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/14/08 RLAS No.: MATRIAL: DIMNSIONING AND TOLRANCING - INDX PART NO. SHT NO. R. S-008- INDX 00 S-008_INDX.DOC

91 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Dimensioning and Tolerancing Scope This section is to establish rules and guidelines for dimensioning and tolerancing and is intended to establish uniform practices for specifying and interpreting design requirements. All dimensions need a tolerance because it is not possible to make a perfect part. To ensure that a design can be fabricated, it is necessary to permit variation on all dimensions. The allowable amount of fabrication error (tolerance) specified on a drawing is normally based on functional requirements. The achievable level of manufacturing accuracy is determined by factors such as process capability. Care should be taken to avoid specifying tolerances that are unnecessarily small. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/25/08 RLAS No.: DIMNSIONING AND TOLRANCING - SCOP MATRIAL: PART NO. SHT NO. 1 R. S S-008_1.DOC

92 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Dimensioning and Tolerancing General Dimensioning Rules Dimensioning of parts must convey enough information to define clearly the engineering intent, so that no scaling of drawings is required, nor any assumptions need to be made. See Section 7.0 Drawings for expanded dimensioning guidelines and examples. All drawings shall use the inch as the unit of measurement. ach dimension must be expressed clearly so that it will be interpreted only one way. No fractional dimensions are to be used; the only accepted practice is decimal dimensioning. Zeros are not used before the decimal but may be added to the right side of the decimal where necessary so that a dimension can be expressed to the same decimal place as its tolerance. No surface, line, or point may be located by more than one toleranced dimension in any one direction. If a dimension is repeated, it is marked RF. Dimensions shall be selected and arranged to avoid accumulation of tolerances. Dimensions are shown on the view that most clearly represents the form of the feature being dimensioned. Dimensions are shown outside the outline of the part unless clarity is impaired. Dimensioning to hidden lines shall be avoided. Dimensions must be selected to give the required information directly so that minimal or no calculations are needed to arrive at usable figures. Where practicable, the finished part should be defined without specifying the manufacturing method. Thus, only the diameter of a hole is given without specifying how it is to be produced. Dimensions out of scale shall be avoided. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/25/08 RLAS No.: DIMNSIONING AND TOLRANCING GNRAL DIMNSIONING RULS MATRIAL: PART NO. SHT NO. 2A R. S S-008_2A.DOC

93 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Dimensioning and Tolerancing General Dimensioning Rules Baseline dimensioning is the preferred method of choice. Wherever possible, all dimensions are to refer to a common reference line (000). The.000 baseline should not be on a raw edge if possible. This method will keep the tolerance accumulation to a minimum. Baseline dimensioning is the only dimensioning method where the dimensions can be rotated and read from the right hand side of the drawing. All other types of dimensioning must be read from the bottom of the drawing. Dimensioning to groups of mounting holes should be with center line to one of the holes and then any holes related will be located from that hole using leader dimensions. When unidirectional dimensioning is to be used, all dimensions and notes should be aligned with the bottom of the drawing. Angles not defined will be 90 with standard tolerance as noted in title box. All dimensions shall be decimal values. The use of fractions is to be avoided. The exception is in the identifier for thread sizes, both fraction and decimal values are acceptable. All dimensions are applicable at 68 Fahrenheit. Compensation may be made at other temperatures. Normal dimensioning of angles is in the direction that the material moved. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/25/08 RLAS No.: DIMNSIONING AND TOLRANCING GNRAL DIMNSIONING RULS MATRIAL: PART NO. SHT NO. 2B R. S S-008_2B.DOC

94 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Dimensioning and Tolerancing Tolerancing Dimensional tolerances may be expressed as follows: Title Block Tolerancing - The tolerances are specified in the title block and depend on the number of decimal places used in the basic dimension. Limit Tolerancing - The high (maximum) value of a dimension is placed above the low (minimum) value. Plus and Minus Tolerancing - The basic dimension is followed by plus and minus tolerance values. Geometric Tolerancing - The tolerances are defined by means of a Feature Control Frame which specifies dimensional limits for an individual geometric feature such as location, orientation, form, profile and runout. The Feature Control Frame is divided into several compartments containing (1) geometric characteristic symbol (which is, when applicable, preceded by a diameter symbol), and (3) datum references as needed. This type of tolerancing is for critical components and should be utilized sparingly. Angle Units - Fractional degrees should be shown using decimal degrees. Tolerance Accumulation Parts should be dimensioned so that the accumulation of tolerances does not affect the overall fit, form, and function of the part itself. Reference Dimensions - A reference dimension is a dimension enclosed in parentheses. It provides auxiliary information that may be helpful in understanding the design requirements and is not considered part of the drawing requirements, and therefore no tolerance is applicable. A reference dimension is generally a repeat of a dimension derived from other values shown on the drawing or on related drawings. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/25/08 RLAS No.: DIMNSIONING AND TOLRANCING TOLRANCING MATRIAL: PART NO. SHT NO. 3A R. S S-008_3A.DOC

95 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID Dimensioning and Tolerancing General Tolerancing Rules Tolerances shall be assigned, directly or as default values, to all dimensions in a drawing. Title block default tolerances shall be used whenever feasible or modified for the drawing requirements. Tolerances shall be specified to meet actual design requirements. Do not use restrictive tolerances simply because they can be easily generated on a CAD station. Bilateral tolerances should be selected instead of unilateral tolerances when plus and minus tolerancing is used. Preference should be given to equal plus and minus values. Tolerances shall have the same number of decimal places as the base dimensions, and have the same character height as the dimensions. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : 8/25/08 RLAS No.: DIMNSIONING AND TOLRANCING GNRAL TOLRANCING RULS MATRIAL: PART NO. SHT NO. 3B R. S S-008_3B.DOC

96 R. RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT RISD NOTS SPCIFYING RF. ADS DRAWINGS. R.D.H. 6/4/90 CHANGD 28 GA. TO MIN. ORDRING SIZ. (ADDD ASTRIC) TC 1/19/94 11/29/93 ADDD TO WORD FORMAT 11/6/07 U.S.S. GAUG COLD ROLLD STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID HOT ROLLD P. & O. ALUMINIZD & GALANIZD RMARKS 5/ / / *.0979* *.0700* * #.0530*.0560* * *$ *+.0340* « *&.0290* *.0230* * * NOTS: * MINUMUM ORDRING SIZD TOLRANC ON PLUS SID ONLY. + HAT XCHANGR ONLY.0329 (20 GA.) & DRAFT DIRTR ONLY.0269 (22 GA.) # HAT XCHANGR ONLY.0548 (16 GA.) $ ROOFTOP LMNT ONLY (18 GA. ALUMINIZD) «DRAIN PAN ONLY.035 (20 GA. GAL.) & ROOFTOP.035 (20 GA. ALUM.) 1. FORT SMITH & MILLDGILL APPLICATION ONLY: S ADS-3918 FOR TYP STL & PAINT RQUIRMNTS. CHKD. BY: APR. BY: RLIAB. NGR.: ND. APP.: DR. BY: CT DAT : 9/7/78 RLAS NO.: RHM SHT STL ORDRING GUID (DCIMAL QUIALNT) PART NO. SHT NO. R. S S-009-_1.DOC

97 RHM MANUFACTURING CO. 01 ADDD RXG-DUMMY KITS R.D.H. 5/25/83 03 RSARCH & DLOPMNT DPARTMNT (CONT D) R S WR: ADDITION OF PAINT SPC S., MILLDGILL INDX & WIR NUT DATA. R.D.H. ADDD ADS-7321 R.D.H. 1/25/ /14/88 UPDATD R. NO. TO SHOW R. DSCRIPTION UPDATD TO WORD FORMAT 11/7/07 03 LFT OFF R.02-3/5/86 STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID DSCRIPTION DWG/INSTR. NO. DSCRIPTION DWG/INSTR. NO. RATING PLAT DATA INDX DAT COD CALNDAR FOR FT. SMITH, NUO LORDO & MILLDILL ADS ADS RB THRAD HOL FORMING PUNCHS & DIS ADHSI APPLICATION & BONDING INSTRUCTIONS ADS ADS SRIAL NO. INSTRUCTIONS FOR STAMPING AIR CONDITIONING RATING PLATS ADS RXG DUMMY KITS ORFIC CALCULATIONS ADS ADS PRODUCT COD OPTION NUMBRS PAINT SPC. CODING FOR TYP STL & PAINT RQ. ADS ADS CAPACITOR STRAP APPLICATIONS PRODUCT PAINT SPCS. MILLDGILL PRODUCT INDX ADS ADS ADS COMPRSSOR APPLICATION ADS MODL NUMBR DATA ADS COMPRSSOR SRIAL NO. MODL COD ADS TST PROCDUR COIL ASSMBLIS ADS BRAZING SPCIFICATIONS ADS WIR SPC. SHTS INDX ADS MASTR PRODUCT INDX ADS TRMINAL CHART/WIR NUT DATA ADS ALUMINUM FIN STOCK SPCIFICATION ADS COIL DSCRIPTION COD ADS STANDARD SADDL TUB HOL ADS FIN PART NUMBR COD ADS SADDL TUB RADII CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: ADS DR. BY: DAT : CT 12/14/79 OFTN RFRRD TO DRAWINGS & INSTRUCTIONS (ADS-) RLAS No.: MATRIAL: PART NO. SHT NO. R. S S-012_1.DOC

98 - RHM MANUFACTURING CO. UPDATD TO WORD FORMAT 11/27/07 Y-0528s001 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID DSCRIPTION DWG/INSTR NO. DSCRIPTION DWG/INSTR. NO. COPPR TUBING (STRAIGHT) CUT LNGTH WIR CUT LNGTHS (STRANDD, SOLID, PARALLL) A A CHARG CHARTS INSPCTION/QUALITY CONTROL LABLS TUB - STRAIGHT 3/8 O.D. W/HOL FOR SADDL A TUB - U BND 3/8 O.D. A LBOWS - 90 COPPR FABRICATD A THRU A HAIRPIN 3/8 O.D. TUB 1) FORMD LNGTH 1.25 CNTRS 2) STRAIGHT LNGTH A A HAIRPIN 5/16 O.D. TUB 1) FORMD LNGTH 1 CNTR 2) FORMD LNGTH.8 CNTR 3) STRAIGHT LNGTH A A A PROCSS STUBS (ALL) A CONDNSR COILS PS ANGLS A APORATOR COILS PS BLANK SIZS A CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : OFTN RRRD TO DRAWINGS & INSTRUCTIONS (A/AS-, PS- & PURCHASD PARTS) CT RLAS NO MATRIAL: PART NO. SHT NO. R. S S-012_2.DOC

99

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120 RHM MANUFACTURING CO. 01 RISD AND RTYPD. RDH UPDATD TO 2008 STANDARDS. MJM UPDATD TO ADD LITRATUR PRODUCTION PROCSS Y-0528S003 JHB RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID SHT NUMBR DSCRIPTION 1 I & O MANUALS/WARRANTIS PROCDUR 2 LITRATUR SHT 3 LITRATUR RISION SUBMISSION RQUST 4 LITRATUR PRODUCTION PROCSS CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : PRINTD MATRIALS - PROCDUR MJM RLAS No.: MATRIAL: PART NO. SHT NO. R. S INDX 03 S-020Index.doc

121 RHM MANUFACTURING CO. 01 RISD DISTRIBUTION OF COPIS. RDH UPDATD TO 2008 STANDARDS. MJM RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID A. NW I & O s and WARRANTIS 1. Installation manuals/warranties required for any product will be prepared by the Publications Specialist in collaboration with the Project ngineer. The rough draft data, with sketches, illustrations, etc. must be made available to the Publications Specialist no later than at the time of the preliminary release. 2. If photographs of product components, or the product, are required for the instructions, it will be the responsibility of the Project ngineer to make the components and/or the product available to the Publications Specialist. The Publications Specialist will be responsible for having the photographs taken and made available for the Printer. 3. The Project ngineer and the Publications Specialist will establish a date on which the preliminary print ready proof must be made available by pre-pilot. The Publications Specialist and the Project Draftsman will be responsible for assigning the Literature Information Sheet part number. 4. The Publications Specialist will have the responsibility of working with the Printer in the preparation of the proof. All changes or revisions must be coordinated with the Publications Specialist, and will contact the Printer. 5. All final proofs are revised and signed off by the Project ngineer, ngineering Manager, Product Manager, and Product Specialist. 6. Printed literature sheet is created and released on a change notice (reference sheets 2A and 2B). 7. Publications Specialist is to provide.pdf format of new literature to be placed in Rheemote.net by Design Services as soon as it is available. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MJM RLAS No.: PROCDUR FOR PRODUCING INSTALLATION & OPRATING INSTRUCTIONS/WARRANTIS MATRIAL: PART NO. SHT NO. R. S 020 1A 02 S-0201A.doc

122 RHM MANUFACTURING CO. 01 RISD DISTRIBUTION OF COPIS. RDH UPDATD TO 2008 STANDARDS. MJM RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID B. RISIONS TO I & O s and WARRANTIS 1. Revisions to Installation Instructions/Warranties are completed by first completing a Literature Revision Request Submission Form (see sheet 3) signed by the ngineering Manager or Product Manager and submitted to the Publications Specialist. 2. A work order is then submitted to Design Services by the Publications Specialist, along with a.pdf file of the revised Installation Instructions/Warranty. Design Services Department will make the requested revisions to the Literature Information Sheet and release it by CN. 3. Upon release, the Design Services Department will then place the.pdf file in the appropriate location behind the Literature Information Sheet in Rheemote.net. 4. The.pdf being replaced will be moved to the change notice mark-up file for future reference. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MJM RLAS No.: PROCDUR FOR PRODUCING INSTALLATION & OPRATING INSTRUCTIONS/WARRANTIS MATRIAL: PART NO. SHT NO. R. S 020 1B 02 S-0201B.doc

123 RHM MANUFACTURING CO. 01 RISD AND RTYPD. RDH UPDATD TO 2008 STANDARDS. MJM RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID TO START A NW INSTALLATION INSTRUCTION SHT IN WORD 1. SLCT FIL. 2. SLCT NW. 3. NOW ON TH NW DOCUMNT POPUP 4. SLCT FROM TH TMPLATS SCTION ON MY COMPUTR. 5. NOW FROM TH TMPLATS POPUP 6. SLCT TH PRINTD MATRIAL TAB. 7. NOW FROM TH PRINTD MATRIAL DIALOG. 8. SLCT TH INSTALLATION INSTRUCTIONS. DOT TMPLAT. Note: if the instruction do not yield the results listed in the above instruction your computer probably has not been setup to the work group templates directory. Please see the following instructions to complete setup or ask for assistance. STTING DFAULT FOLDR FOR WORK GROUP TMPLATS IN WORD 2003 Create and release 1. FROM TH TOP MNU BAR 2. CLICK TOOLS DROP DOWN. 3. CLICK OPTIONS DROP DOWN. 4. SLCT FILS LOCATIONS TAB FROM TH DIALOG BOX. 5. DOUBL CLICK WORKGROUP TMPLATS. 6. BROWS TO YOUR DSIRD FOLDR LOCATION. 7. SLCT OK. STTING DFAULT FOLDR FOR WORKGROUP TMPLATS IN WORD CLICK TH OFFIC BUTTON IN TH UPPR LFT CORNR OF TH SCRN 2. CHOOS WORD OPTIONS FROM TH BOTTOM RIGHT OF TH POP UP MNU. 3. SLCT ADANCD SCROLL DOWN TO TH GNRAL SCTION. 4. SLCT TH FIL LOCATIONS BUTTON. 5. SLCT WORKGROUP TMPLATS. 6. CLICK TH MODIFY BUTTON. 7. BROWS TO TH DSIRD FOLDR LOCATION. 8. SLCT OKAY. R&D WORD TMPLATS CAN ALWAYS B FOUND IN TH O:\ FORMS\ DIRCTORY. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : PRINTD MATRIALS - PROCDUR MJM RLAS No.: MATRIAL: PART NO. SHT NO. R. S A 02 S-0202A.doc

124 RHM MANUFACTURING CO. 01 RISD DISTRIBUTION OF COPIS. RDH UPDATD TO 2008 STANDARDS. MJM RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : MJM RLAS No.: FORMAT INSTRUCTIONS FOR LITRATUR INFORMATION SHT FOR INSTALLATION & OPRATING INSTRUCTIONS/WARRANTIS MATRIAL: PART NO. SHT NO. R. S 020 2B 02 S-0202B.doc

125 RHM MANUFACTURING CO. 01 RISD DISTRIBUTION OF COPIS. RDH UPDATD TO 2008 STANDARDS. MJM ADDD NW FORM AND INSTRUCTIONS Y-0528S003 JHB 8/4/10 RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID INSTRUCTIONS FOR LITRATUR RQUST SUBMISSION FORMS The Factory Literature (New/Revision) Request Submission Form should be used when requesting a change or addition to XISTING factory literature or producing NW factory literature that is packaged with the model at the time of manufacture. The form can be found as an editable PDF at L:\Factory Literature Production Files. The Urgency Level of the request must be noted on the form. Factory Literature (NW/RISION) Request Submission All factory literature part numbers that will be effected by the request MUST be listed on the form. This includes ALL private labels, export, Sure Comfort and any foreign language conversions. Must provide an implementation date for all literature so that vendors/materials/planners have an actual date to work with. All Files Required for Literature Completion should be loaded at L:\Factory Literature Production Files PRIOR to submitting this form to the Publications Specialist. ach filename must be listed on the form. New Project or Maintenance Project Number must be listed on the form. IMPORTANT: RISIONS TO ANY XISTING FACTORY LITRATUR SHOULDNOT B RLASD ON AN CN UNTIL A WORK ORDR HAS BN SUBMITTD BY TH PUBLICATIONS SPCIALIST 7/14/2010 M. Thomas CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: MJM 7/14/2010 DAT : M Thomas LITRATUR RISION RQUST SUBMISSION FORM RLAS No.: MATRIAL: PART NO. SHT NO. R. S S-0203.doc

126 RHM MANUFACTURING CO. RSARCH & DLOPMNT DPARTMNT STANDARD TOLRANC UNLSS OTHRWIS NOTD: -FRACTIONAL ± 1/32 -ANGULAR DCIMAL ±.030 -RFRNC ( ) NOT: ALL BRAKS AR 90 UNLSS OTHRWIS SPCIFID START HR: If new literature or revision requires work to be completed by Design Services & R&D Database Administrator LITRATUR PRODUCTION PROCSS Project ngineer provides Designer/Design Services hard copy markups along with a work order, of any illustration, charge chart, wiring diagram, troubleshooting chart or any other R&D owned drawing required for Literature Completion. (IMPORTANT: IF ABO MNTIOND FIL TYPS AR SNT TO CALRT FOR PRPRSS PRODUCTION, THOS FILS MUST STILL B PROPRLY RCORDD BY DSIGN SRICS IN TH WINDCHILL PDMLINK. DSIGNR/NGINR SHOULD NOT DIRCT CALRT TO CHANG OUT ANY DRAWINGS IN I&OS OR USRS MANUALS) Designer/Design Services returns any requested revised/new illustrations, charge charts, wiring diagrams, troubleshooting charts or any other misc. drawing to the Project ngineer for approval. Once approval is granted, PROJCT NGINR IS RSPONSIBL FOR NSURING AN LCTRONIC FIL OF ACH DRAWING IS PLACD IN TH APPROPRIAT FOLDR FOUND AT L:\FACTORY LITRATUR PRODUCTION FILS. FILS MUST B NAMD BY FULL PART NUMBR INCLUDING RISION LL. (FOR XAMPL: ) 7/13/2010 M. Thomas (IMPORTANT: ON WIRING DIAGRAMS AND CHARG CHARTS, ILLUSTRATOR PS FILS AR TH PRFRRD FIL TYP BY ALL LITRATUR NDORS) START HR: If new literature or revision requires work to be completed only by R&D Database Administrator Project ngineer provides R&D Database Administrator all information required for production of any electronic data files required for Literature Completion. (xample: General Data, lectrical/physical, System Combinations, Heater Kits, etc.) R&D Database Administrator works with the Project ngineer to complete all required data. Once approval is granted, PROJCT NGINR IS RSPONSIBL FOR NSURING ALL LCTRONIC DATA FILS AR PLACD IN TH APPROPRIAT DATA FOLDR FOUND AT L:\FACTORY LITRATUR PRODUCTION FILS. Files must include the model number and date loaded. (xample: (-)APM-JAZ ) (IMPORTANT: ANY DATA FILS NOT PRODUCD BY TH R&D DATABAS ADMINISTRATOR SHOULD ALSO B LOADD BY TH NGINR ONL:\FACTORY LITRATUR PRODUCTION FILS) Project ngineer provides hard copy literature markup AND a complete Literature Request Submission Form (S FORM INSTRUCTIONS FOR DTAILS) to the Publications Specialist. IMPORTANT: ALL FILS RQUIRD FOR NW LITRATUR OR RISIONS SHOULD B COMPLTD AND ALRADY LOADD AT L:\FACTORY LITRATUR PRODUCTION FILS BFOR MARKUP AND RQUST FORM AR SUBMITTD. START HR: If new literature or revision doesn t require any work by Design Services or R&D Database Administrator Literature Revisions submitted by Product Managers or Specialists: Fill out the appropriate submission form, and attach a hard copy markup. If requested changes require work by Design Services or R&D Database Administrator, the Publications Specialist will submit tothe appropriate R&D ngineer. LITRATUR MARKUPS SHOULD B CLARLY MARKD. DRAWING & DATA INSRTIONS MUST B CLARLY MARKD BY FILNAM. TH BTTR TH MARKUP-TH MOR ACCURAT TH PROOF.4-6 WKS SHOULD B SCHDULD IN TH PROJCT TIMLIN FROM THIS POINT FOR ACTUAL LITRATUR PRODUCTION ON XISTING FACTORY LITRATUR, ONC RISIONS AR COMPLTD, A WORK ORDR WILL B SNT IN BY TH PUBLICATIONS SPCIALIST FOR CN RLAS. Publications Specialist will process all factory and sales literature requests according to urgency level, and will ensure proper approvals are received & filed from R&D and Product Managers. Publications Specialist will be responsible for submitting work orders to Design Services for revisions to existing factory literature, once the revisions are complete. Publications Specialist will ensure that final literature files are sent to Customer Service for PTS posting and are posted to Partners system. Publications Specialist will maintain a Status Report on all literature requests. CHCKD BY: APPROD BY: RLIAB. NGR.: NDOR APPROAL: DR. BY: DAT : JHB LITRATUR PRODUCTION PROCSS RLAS No.: Y-0528S003 MATRIAL: PART NO. SHT NO. R. S S-0204.doc