lindab cover line installation instructions lindab roca Lindab CoverlineTM Lindab Roca Installation instructions
|
|
- Juliana Curtis
- 5 years ago
- Views:
Transcription
1 lindab cover line installation instructions lindab roca Lindab CoverlineTM Lindab Roca Installation instructions
2 Preparation Before you start Before starting work, read the installation instructions in their entirety to get an idea of which items need to be implemented on just your roof and in what order these should be done. Lindab Roca must be installed on an impermeable ceiling and fitted directly to battens and counter-battens. In free roof areas, installation is very easy. If the roof has a lot of obstacles or cupolas, the work required will be much more involved. Lindab is a turnkey supplier of roofing systems and roofing products and, in addition to metal roofing, can also supply you with roof drainage systems, transitions, roof bridges, snow fences and roof ladders. Opening the box Start by checking that your order is complete and that all items on the bill have been supplied. Then review the products and ensure that nothing has been damaged during shipping. If you find that damage has occurred during shipping, you must immediately report this. Unloading of goods Lindab Roca is supplied on standard size pallets. The panels can be stored outside provided they are installed within a month. Otherwise, they should be stored under cover out of the rain. Safe working Always wear protective gloves and clothing. Use a safety line and softsoled footwear when working on the roof. All existing safety regulations must be observed while working with Lindab Roca. It's fine to walk on the roof, but your feet should ideally be placed in the indentations of the panels and on battens. Ceiling Make sure the surface is in good condition before installing your new roof. The roof profile should be fitted on an impermeable surface with a roof slope of 14 or more. The panels are placed on battens and counter-battens measuring 25x35 mm. The distance between the battens is 370 mm. Chimney and transitions Fittings around the chimney should be made by a metalworker to ensure a tight and good-looking installation. Lindab has a range of ready to use products to create different types of transition on the roof surface. Roof maintenance The roof is for the most part kept clean and free of dirt by it being rinsed by the rain. Leaves and twigs may become trapped in the nooks and should be cleaned out annually. If the roof needs to be washed, the best way is to use a soft brush and warm water. Lindab is not responsible for costs incurred replacing products installed using a method other than the one shown in these installation instructions. 2
3 Preparation Fasteners It is important to use the correct fasteners for all sheet-metal structures. When you use the fasteners from Lindab, you can be sure that they are designed for the purpose and safe to use. Ideally, Lindab Roca is installed using screwdrivers. Use A12 screws measuring 4.8 x 35. Installation instructions In contrast to laying a traditional sheet metal roof, you start fitting Lindab Roca from the roof ridge. The panels are easy to handle and are laid by lifting the last panel laid and sliding the panel you want to fit underneath. Always start with row 1 as shown in the instructions. Then install row 0, which is the panel row that connects everything to the roof ridge. Then secure the ridge tiles before installing the remaining panel rows. This provides a good base on which to stand, eliminating the necessity of "walking" on laid panels. Once rows 0 and 1 have been laid, the remaining panels are installed in order downward towards the eaves. Fit and cutting If the sheet must be cut, use a pair of snips or a circular saw with a blade designed for thin sheet metal. Never use an angle grinder. Use a sharp object, knife or similar to mark cut and fold lines. Tools To install the roof, you will need the following tools. Screwdrivers and bits Snips Rubber mallet Knife Folding tongs Ruler Circular saw Work gloves and shoes with soft soles Safety line 3
4 Technical information Components Lindab Roca roof panel Rustica / Prestige Lindab Roca ridge tile NP Lindab Roca terminator, ridge tile NPG Ridge sealing tape & Wakaflex Ridge sealing tape width = 295 mm Wakaflex Width = 280 mm 4
5 Technical information Components Lindab eaves board FOTP Lindab gutter RDF Lindab Roca cladding INKL Roca Lindab flashing VISK 5
6 Installation Lindab Roca Preparation Attach the flashings with triangular moulding on the roof. When mounting the barge boards, add a strip of roofing felt under the plate. Splicing is carried out with 100 mm overlap. FOTP barge board should overlap the trailing edge of the gutter. Make sure that the plate is placed in a straight line along the edge of the roof. Screw in a zig-zag pattern, leaving 300 mm between attachment points. Roof pitch 14º 18º 22º H Roof pitch 27º 38º 45º H Place the protective surface of the roof in accordance with the manufacturer's instructions. Cover eaves board flashing bolts. 6 For ridge boards, a 45 mm wide joist is used. Adjust the height of the ridge board in accordance with the table to the right, so that the ridge tiles can rest against the ridge board and be secured from above.
7 Installation Lindab Roca Attach counter battens 25x35 mm c / c 600 mm. Attach battens 25x35 mm with A = 370 mm distance. Start at the eaves and go upwards. Measurement B is the distance that is "left over". The top row of panels must be cut here. Row 1 Place Lindab Roca cladding plate INCL against the bottom batten. Splicing is carried out with 100 mm overlap. Secure with screws in the bottom batten. Start by folding the edge of the first sheet 20 mm for all plates that are added to edge towards the flashings. Place the first plate against the flashing as shown in the figure. Always start by adding row 1. Remember to overlap the panels. The last panel in the row will probably need to be cut. Use snips. Don't forget to fold the edge toward the flashing 20 mm. 7
8 Installation Lindab Roca Row 0 When this measures less than 370 mm, the panels in row 0 must be cut lengthwise. Use snips. Remember to ensure that the overlap seams do not end up in the same place but are displaced. Ridge Place the ridge belt along the ridge. Nail down as indicated by the markings. Remove the protective plastic from the adhesive compound. Press the ridge belt down towards the bottom of the panel. Lay out the ridge tiles. Start from both ends of the roof, working towards the middle. Screw ridge tiles in every joint from the top down into the ridge board. Place the final two ridge tiles by overlapping them. Trim the ends first. 8
9 Installation Lindab Roca Rad 2, 3 osv The panels in rows 2, 3, 4, etc. are laid by lifting the panel above and then sliding the panel you want to fit underneath. Continue in the same way for each row. Then secure the panels between row 0 and row 1. Use a screwdriver to secure the panels. One screw in the top of every second panel. Once row 3 has been laid, rows 1 and 2 can be secured. Secure the last row laid at the top of each panel. 9
10 Installation Lindab Roca Flashing Secure Roca FR-R flashings using screws c / c 400 mm. Start at the ridge. Splicing is carried out with 100 mm overlap. Guttering The flashing must be placed below the outer ridge tile. Cut a notch in the ridge tile to accommodate the flashing. Finish with Lindab Roca terminators. Secure counter-battens 152 mm from the centre of the gutter. Place the gutter on the adjacent battens and secure by screwing into the battens. Adjust and cut the panels as evenly as possible in parallel with the gutter. Make sure to get a 40 mm overhang on the panels over the gutter. For gutters longer than 2000 mm, use profiles with an overlap of at least 200 mm. Apply sealant to the overlap. 10
11 Installation Lindab Roca Seal around the chimney Place the cut sheets around the chimney. Apply Wakaflex (or similar) around the chimney and the on top of the tiles. Start at the front. Continue along the sides and over the previously laid Wakaflex. Secure right up to the upper seal. Cover the wakaflex above the chimney with a roof profile. Seal around the chimney with sheet metal. 11
12 lindab coverline installation instructions lindab roca Lindab is an international group that develops, manufactures, markets and distributes products and system solutions of thin sheet metal and steel that simplify construction and improve the indoor climate. Our range includes everything from complete construction systems to individual components for homes, commercial properties and industrial premises. The Lindab Group has approximately employees in 31 countries. Its head office is located in Grevie near Båstad in north-west Skåne. Art no. xxx
Roofs. Installation instructions Models Classic C and D
Roofs Installation instructions Models Classic C and D A complete roof includes a lot more than just the roofin g sheets. A combination of lead-ins, water removal systems, ladders, roof bridges and snow
More informationINSTALLATION GIUDE.
INSTALLATION GIUDE INTRODUCTION The instructions and drawings included here are intended only as a guide for the installation of ECO Roofing Systems Spanish and Modern profiles. The materials and methods
More informationTable of Contents Light Gauge Metal Roof & Wall Panels
Table of Contents Light Gauge Metal Roof & Wall Panels Installation Guide for Delta Rib, Nor-Clad, Strata Rib & 2-1/2 Corrugated Introduction Important Notice Notes: April 2008 Minimum Recommended Tools
More informationAQUAGARD EPDM FLAT ROOFING SYSTEMS INSTALLATION GUIDE THE MECHANICALLY FIXED SYSTEM
AQUAGARD EPDM FLAT ROOFING SYSTEMS INSTALLATION GUIDE THE MECHANICALLY FIXED SYSTEM The following guide covers the technique for the Mechanically Fixed System. This system is best employed when an overlay
More informationRoofing Training - Basics. Sandy Wesch
Roofing Training - Basics Sandy Wesch Tools Hammer Measuring Tape Chalk Line & Chalk Speed Square Framing Square Utility Knife Metal Snips Extension Ladder(s) 2 Safety Any tools or material up on the roof
More informationStraight Rib Series Metal Roofing Panel Installation Guide
D-Rib G-Rib C-Rib Straight Rib Series Metal Roofing Panel Installation Guide 7000 AIRPORT LINE R.R., BOX 7 HENSALL, ONTARIO N0M X0 EASY BUILDING PRODUCTS TEL. : 5-6-07 TOLL FREE : -888-76-777 FAX: 5-6-08
More informationRoofs. Installation instructions Models Monterrey and Elite
Roofs Installation instructions Models Monterrey and Elite A complete roof includes a lot more than just the roofing sheets. A combination of lead-ins, water removal systems, ladders, roof bridges and
More informationinstallation guide Villa
installation guide Villa Table of Contents Introduction............................. 2 Safety................................... 2 Tools.................................... 2 Codes & Requirements....................
More informationBarrel Vault Counter Batten and Batten
Barrel Vault Counter Batten and Batten INSTALLATION GUIDE www.gerardusa.com INSTALLATION NOTIFICATION The installation procedures demonstrated in this manual are recommended methods for the installation
More informationThree layer Felt Roofing using cold applied adhesive
Three layer Felt Roofing using cold applied adhesive Useful tips - Skill level - Safety - Felt Roofing Materials - Tools and Equipment Laying a felt roof is within the capabilities of most diy people providing
More informationSapphire Metal Tile Roofing System. Installation Guide
Sapphire Metal Tile Roofing System Installation Guide Overview - Sapphire Installation Guide FIG. 1 CROSS-SECTION 7-¼" Overall width = 46-7/16" Coverage width = 43-5/16" SAPPHIRE 350 Rib Height = 1-9/16"
More informationInstallation Guide. Step 3. Valley Flashing. Step 7. Transition Flashings and Accessories. Step 6. Hip and Ridge Installation
Step 7. Transition s and Accessories Step 3. Valley Step 6. Hip and Ridge Installation Step 2. Rake Trim Step 5. Installing the Shingles Step 1. Eave Starter Installation Step 4. Endwall s Installation
More informationBARRELL VAULT BATTENLESS
i BARRELL VAULT BATTENLESS INSTALLATION GUIDE INSTALLATION NOTIFICATION The installation procedures demonstrated in this manual are recommended methods for the installation of the Gerard Barrel Vault battenless
More informationFIXING GUIDE. Designed for Garages & Sheds, Houses, DIY, Flat Roofs, Industrial & Agricultural Buildings etc. IS THE LONG TERM ROOFING SOLUTION
FIXING GUIDE Designed for Garages & Sheds, Houses, DIY, Flat Roofs, Industrial & Agricultural Buildings etc. IS THE LONG TERM ROOFING SOLUTION Permaroof Permaroof Permaroof Profile Roofing Manufacturers
More informationlindab we simplify construction LindabSandwichPanels Installation instructions PIR Panels
lindab we simplify construction LindabSandwichPanels Installation instructions PIR Panels Assembly instructions Before you start Check that the panel support structures are level. Position the packages
More informationAssembly instructions
Assembly instructions Plannja Profiles 20 105, 20 75, Sinus 18, Sinus 51, 45, 45R, 19R, 35 including flashings and fittings 2017 Roofing Sheet & Wall Cladding TABLE OF CONTENTS Some words of advice...
More informationGambrel Barn with Overhang Manual
Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Square utility knife w/ blade & hook blade -Speed Square Little Cottage Co. PO Box 455 Berlin, OH
More informationInstallation Guide Simplicity Alfresco. V1.9 Lu070318
0333 305 5272 www.canoports.co.uk Installation Guide Simplicity Alfresco V1.9 Lu070318 Tools Required Below is a list of tools that you will require to install your the Simplicity Alfresco System. Cordless
More informationInstallation Manual. This installation is for the Odyssey H1800 Series Ventilation System.
Installation Manual This installation is for the Odyssey H1800 Series Ventilation System. This installation is limited to roofs with pitches between 3 and 35. This instruction assumes that there is a power
More informationFive Star Panel Installation Instructions
Five Star Panel Installation Instructions How to Store Five Star Panels You will need to store FIVE STAR PANELS in dry place to prevent staining, deterioration and possibly void all warranties. Stand the
More informationTuff-Rib Install Guide
Install Guide bestbuymetalroof.com Page 2 of 27 Page 3 of 27 1. Page 4 2. a. Installation Guide b. Panel Squaring Pages 5, 6 Pages 7, 8 3. Pages 9, 10 4. a. Fascia (optional) b. Eave / 1.5x3.5 Angle c.
More informationInstallation Guide. 203 Chesterra Drive, Dahlonega, GA Toll-Free ~ Fax ~
Congratulations and Thank You for your purchase! DryJoistEZ is an easy to install structural aluminum joist that also provides an under-deck drainage system that you install over your deck framing system
More informationOctagon Vinyl Gazebo Assembly Instructions
Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 04/29/09 Vinyl Gazebo Assembly
More informationShingle Installation Guide
Installation Guide Roof Framing Information Installation Installation Accessory Installation Estimating Data General Information Roof Framing Information It is the responsibility or roofers, building contractors
More informationCountry Cabin. Assembly Manual. HomePlace Structures
Country Cabin Assembly Manual Country Cabin Assembly Manual revised 3/20/10 Dear Customer, Thank you for your purchase of our Country Cabin. The craftsmanship and detail in this building is unmatched.
More informationASSEMBLY INSTRUCTIONS GG77. BASE SIZE: 2.190m x 2.020m
ASSEMBLY INSTRUCTIONS GG77 BASE SIZE: 2.190m x 2.020m CONGRATULATIONS ON PURCHASING A DURATUF GUARDIAN SHED. BEFORE YOU BEGIN THE ASSEMBLY PLEASE NOTE SOME IMPORTANT POINTS: BEFORE YOU START: Read all
More informationPV SLATE ROOF INSTALLATION GUIDE
The PV Slate roof tile is designed to integrate into a roof clad with either natural or imitation slates. Initial Roof Batten Layout. The roof should be battened using 50x25mm batten at a spacing of 270mm.
More informationTable of Contents. Fasteners... 4 Venting Preparation Installation with Battens - DECRA Tile & DECRA Shake 1
Table of Contents DECRA Tile & Shake Roof Overview... 2 Introduction... 3 Safety... 3 Tools.... 3 Estimating Sheets... 4 Codes & Requirements... 4 Roof Slope... 4 Underlayment... 4 Deck Preparation....
More informationEffective February, 2015
Effective February, 2015 Table of Contents Ensuring System Performance 1 Components 2 Frequently Asked Questions 3 List of Tools 3 Before you Begin Preparation 3 Quality Tips 4 Cold Weather Tips 4 Cleaning
More informationASSEMBLY INSTRUCTIONS SS2520. BASE SIZE: 2.520m x 2.020m
ASSEMBLY INSTRUCTIONS SS50 BASE SIZE:.50m x.00m CONGRATULATIONS ON PURCHASING A SMART STORE SHED. BEFORE YOU BEGIN THE ASSEMBLY PLEASE NOTE SOME IMPORTANT POINTS: BEFORE YOU START: Read all instructions
More informationWave Profile Installation Guide
Wave Profile Installation Guide American Pa o Covers Plus Proudly Builds With Tools & Hardware Wave Profile Installation Guide Tape Measure Square Level Felt tipped Marker and/or grease pencil 3/8" Nut
More informationInstallation Guide. Guardian Slate Roof System. England, Scotland & Wales
Installation Guide Guardian Slate Roof System England, Scotland & Wales March 2016 Product Information Construction: Manufactured from resin bonded crushed limestone Size (slate): 445 x 294mm (ridgecap):
More informationROOF FRAMING INFORMATION BATTEN INSTALLATION CORONA SHAKE INSTALLATION ACCESSORY INSTALLATION ESTIMATING DATA GENERAL INFORMATION
ROOF FRAMING INFORMATION BATTEN INSTALLATION CORONA SHAKE INSTALLATION ACCESSORY INSTALLATION ESTIMATING DATA GENERAL INFORMATION ROOF FRAMING INFORMATION It is the responsibility or roofers, building
More informationASSEMBLY INSTRUCTIONS GL75. BASE SIZE: 2.190m x 1.520m
ASSEMBLY INSTRUCTIONS GL75 BASE SIZE: 2.190m x 1.520m CONGRATULATIONS ON PURCHASING A DURATUF GUARDIAN SHED. BEFORE YOU BEGIN THE ASSEMBLY PLEASE NOTE SOME IMPORTANT POINTS: BEFORE YOU START: Read all
More informationMANUAL MOUNTING SYSTEM FOR BITUMEN / EPDM
MANUAL MOUNTING SYSTEM FOR BITUMEN / EPDM EN mounting system for insulated pitched roof Bitumen / EPDM for solar panels landscape setup ESDEC BV 2015 TABLE OF CONTENT 1. Introduction 1 2. General installation
More informationASSEMBLY INSTRUCTIONS SS2010. BASE SIZE: 2.020m x 1.020m
ASSEMBLY INSTRUCTIONS SS010 BASE SIZE:.00m x 1.00m CONGRATULATIONS ON PURCHASING A SMART STORE SHED. BEFORE YOU BEGIN THE ASSEMBLY PLEASE NOTE SOME IMPORTANT POINTS: BEFORE YOU START: Read all instructions
More informationStone coated steel roof tile INSTALLATION GUIDE
Stone coated steel roof tile INSTALLATION GUIDE Ⅰ. Introduction These installation details are provided to demonstrate recommended installation methods for KD One roof products and accessories. Consult
More informationSUPREME WALL GARDEN ASSEMBLY INSTRUCTIONS 24/08/16 www.hallsgreenhouses.com Please refer to website for the most up to date instructions. SAFETY WARNING 1. Always wear protective glasses, shoes, gloves
More informationGABLE ROOF CARPORT RECOMMENDED INSTRUCTION MANUAL
GABLE ROOF CARPORT RECOMMENDED INSTRUCTION MANUAL Table of Contents Introduction 2 Components 3 Step 1a Marking out the Perimeter of the Carport with Footing only 3 Step 2a Footing Set-Out for Concrete
More informationOctagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models
Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 04/29/09 Vinyl Gazebo Assembly
More informationIDAHO ASSEMBLY INSTRUCTIONS. BASE SIZE: 1.800m x 1.200m
IDAHO ASSEMBLY INSTRUCTIONS BASE SIZE: 1.800m x 1.200m IDAHO Tools Required: Battery Drill Riveter Hammer Tape Measure Ladder Skillsaw Level Square Drive Bit No.2 3/8 Hex Drive Bit 8mm Hex Drive Bit Drill
More informationAssembly Instructions
10' and 12' Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/20/09 Cedar Gazebo Assembly Instructions
More informationMONO PITCHED CHIMNEY FITTING INSTRUCTIONS STANDARD LITESTACK CHIMNEY FITTING INSTRUCTIONS HEALTH & SAFETY WARNING:
MONO PITCHED CHIMNEY FITTING INSTRUCTIONS STANDARD LITESTACK CHIMNEY FITTING INSTRUCTIONS HEALTH & SAFETY WARNING: THESE INSTRUCTIONS ASSUME THAT THE CHIMNEY IS BEING FITTED BY A PROFESSIONAL CONSTRUCTION
More informationTape Measure Metal Clippers Screw Bit Set With Extensions
IMPORTANT: Read through instructions thoroughly before beginning to replace any damaged material. Minor damage can be fixed with a fiberglass repair kit and color matched paint. Tools Required Tape Measure
More informationTuff Rib Panel Installation Specifications
Tuff Rib Panel Installation Specifications ROOF APPLICATION: Roof slope must be a minimum of a 2/12 pitch to use this product. For slopes lower than a 3/12 pitch, lap sealant is suggested on the side laps
More informationInstallation Manual. Future Roof Shingle / Slate Products
Installation Manual Future Roof Shingle / Slate Products REVISED 14/09/2010 Future Roof Shingle Installation Manual is a component of Future Roof, Inc. and as such is intended to be used with Future Roof
More informationMETAL ROOFING INSTALLATION GUIDE
METAL ROOFING INSTALLATION GUIDE STANDING SEAM ROOFING PANELS Horizon 16 and Climaguard 16 Regardless of whether your roofing project is a new installation or a re-roof, and whether your building is residential,
More informationmanthorpe Roll-Out Dry Fix Ridge System building products Fixing Instructions MBP 8265e
manthorpe building products Roll-Out Dry Fix Ridge System Fixing Instructions MBP 8265e Ridge Details Fig A. Assembly View of Dry Ridge Detail s/s screw clamping plate rubber washer foam spacer ridge tile
More informationGIRTS ON BACK OF BUILDING
GIRTS ON BACK OF BUILDING ALL GIRTS ARE 1 1/2 SQUARE TUBE. GIRT LENGTHS FOR 12, 20, 24, AND 30 WIDE BUILDINGS: ON 12 WIDE BUILDINGS GIRTS ARE 67 3/4 LONG ON 20 WIDE BUILDINGS GIRTS ARE 56 3/4 LONG ON 24
More informationInstructions for Installation on a Pitched Roof LIGHTWAY optical tube LW 260, LW 320, LW 520, LW 760
Lightway, s.r.o. Registered office: Ledvinova 1714, 149 00 Praha 4 Offices: Za Humny 1054/4a, 161 00 Praha 6 tel.: 235 300 694, fax: 235 300 218 Company ID No.: 63669366, Tax ID No.: CZ63669366 Bank: KB
More informationIMPORTANT!!! ASSEMBLY ASSEMBLY INSTRUCTIONS. (Internal Dimensions)
ASSEMBLY ASSEMBLY INSTRUCTIONS (Internal Dimensions) Ent Spec Edition Ltr v-0- Overall dimensions including base: 7. L x 9 W x 0 H cms 97.5" L x 7" W x 8.7" H IMPORTANT!!! Please read these instructions
More informationAdorn Mortarless Stone Veneer Installation Natural Concrete Products
Adorn Mortarless Stone Veneer Installation Adorn Mortarless Stone Veneer can be used on new or existing construction. Adorn is nailed or screwed onto the wall; therefore no brick ledge is required. Adorn
More informationEffective April 1, 2013
Effective April 1, 2013 Table of Contents Ensuring System Performance 1 Components 2 Frequently Asked Questions 3 List of Tools 3 Before you Begin Preparation 3 Quality Tips 4 Cold Weather Tips 4 Cleaning
More informationInstallation Instructions Palladium Wall Panels - Demountable Factory Finished Edges and Field Cut Edges
Please read all instructions before installing Palladium Wall Panel System. 1. Before installation: a. Acclimate Palladium Panels, reveals, adhesives and wall substrates to room temperature 24 hours before
More informationCertainTeed. Shake / Slate Installation Guide
CertainTeed Shake / Slate Installation Guide Table of Contents System Components... 2 General Conditions, Safety and Roof Preparations... 3... 4 Eave/Drip Edge... 5 Inner Gable... 6 Outer Gable... 7 Open
More informationItem Checklist & Additional Tools Required For Installation
Product Manual Item Checklist & Additional Tools Required For Installation Included Parts: Qty: 1 Maestro BAL Ventilator 1 2 Speed Controller 1 3 Power Supply 1 4 Fixing Strap 1 5 Speed Controller Fixing
More informationREGENCY TIMBER BUILDINGS
REGENCY TIMBER BUILDINGS TEL 01948 830460 UNIT 22 PENLEY IND EST, PENLEY.WREXHAM. LL13 0LQ 1 Garage fitting instructions Tools needed handsaw, hammer, Stanley knife with hook blade, tape measure, battery
More informationDUTCH GABLE CARPORT RECOMMENDED INSTRUCTION MANUAL
DUTCH GABLE CARPORT RECOMMENDED INSTRUCTION MANUAL Table of Contents Introduction 2 Components 3 Step 1a Marking out the Perimeter of the Carport with Footing only 4 Step 2a Footing Set-Out for Concrete
More informationShed Assembly Instructions
Shed Kit Contents The shed kit includes all the parts needed to assemble your shed except for tools and fasteners such as screws and nails. The various pieces are pre-cut and many are marked to indicate
More informationlindab we simplify construction LindabStandingSeamRoofing Application guide
lindab we simplify construction LindabStandingSeamRoofing Application guide This handbook deals with long strip roofing with Lindab PLX on a boarded roof covering. The instructions in this handbook are
More informationConstruction details: Master-C type profiles and joints:
Construction details: Master-C type profiles and joints: Master-C 3g 32 mm. (1 1/4 ) 1000 mm. (39 3/8 ) outer face inner face 10.5 fixing details: sealing washers shall be installed through a 2-3/8 x 1-9/16
More informationBrava Old World Slate Installation Guide
Brava Old World Slate Installation Guide Brava Roof Tile Phone: 844-290-4196 www.bravarooftile.com This document includes the recommended and suggested installation procedures for Brava Old World Slate
More informationDETAIL MANUAL for Standing Seam / Image II
DETAIL MANUAL for Standing Seam / Image II Best Buy Metals Toll Free 1-800-728-4010 / Phone 423-479-6382 / Fax 423-728-3066 www.bestbuymetals.com Best Buy Metals Standing Seam Roofing Panels Fig. 2 Standing
More informationNEVADA ASSEMBLY INSTRUCTIONS
NEVADA ASSEMBLY INSTRUCTIONS BASE SIZE: 2.700m x 1.500m NEVADA Tools Required: Battery Drill Riveter Hammer Tape Measure Ladder Skillsaw Level Screwdriver - Flat 3/8 Hex Drive bit 8mm Hex Drive bit Drill
More information12ft Octagon Bayside Gazebo Assembly Manual
We recommend reviewing this Assembly Manual thoroughly before starting this project. Become familiar with the tools required and where and when assistants are necessary. If you re planning on finishing
More informationCorrugated Installation and Technical Guide
Corrugated Installation and Technical Guide AmeriLux International, in partnership with Menards, offers high quality polycarbonate, pvc and fiberglass panels which feature the latest in product technology.
More information2 ½ Corrugated Panel Installation Specifications
2 ½ Corrugated Panel Installation Specifications ROOF APPLICATION: Roof slope must be a minimum of a 2/12 pitch to use this product. When using this product butyl lap sealant is recommended for all slopes.
More informationShingle Installation Guidelines
Shingle Installation Guidelines General Guidelines Materials to be used Key definitions Cost of roofing Preparation of the roofing deck Materials used for roofing should conform to approved norms and regulations
More informationPBR Panel Installation Specifications
4906 St. Stephens Rd. 5780 Hwy 90 W Eight Mile, Al 36613 Theodore, AL 36590 251 456 2254 251 653 1550 251 457 2254(F) 251 653 1514(F) PBR Panel Installation Specifications ROOF APPLICATION: Roof slope
More informationSunhouse. Assembly Manual
Sunhouse Assembly Manual Thank you for your purchase of this sunhouse. Sunhouse Assembly Manual This manual is designed to simplify the assembly process, however we recommend having an experienced carpenter
More informationTapersawn Shake Installation Instructions
Smart-Shingle TM System Tapersawn Shake Installation Instructions INSTALLATION GUIDE MARKS Shake-Strip 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
More informationInstallation Manual. Last Updated 4 February, Postal PO Box 932 Bayswater VIC
Installation Manual Last Updated 4 February, 2013 Part 1: Provided Material The Panel Expandable Foam Sealing Strip Barge Capping Z-Fascia Structural Screws Timber: 3/8 head size Metal: 5/16 head size
More informationOptiLiner Banded Liner System Bi-Directional Banding
TOP LAYER UNFACED INSULATION ROOF SHEET LINER BOTTOM LAYER UNFACED INSULATION General Introduction The OptiLiner Banded Liner System is designed to provide maximum thermal performance in preengineered
More informationCROSSBAR RAFTER ISOMETRIC
Super Sky Products' typical glazing system consists of glass panels or "lites" which are attached to the main framing members using extruded aluminum "retainers" or "pressure plates". These retainers are
More informationPotting Store Assembly Instructions
Before assembly We recommend that time is taken to read the instructions before starting assembly, then follow the easy step by step guide. The instruction sheet is only a guide to the assembly. Certain
More informationViva Synthetic Thatch Installation Instructions
Viva Synthetic Thatch Installation Instructions Overview Structure This instruction manual is for the installation of VIVA on an open battened roof frame. Structure should be framed with weatherable wood
More informationRIDGEMASTER PLUS CAUTION INSTALLATION INSTRUCTIONS ALWAYS WEAR SAFETY GLASSES TOOLS NEEDED GENERAL GUIDELINES FOR RIDGEMASTER PLUS AND HIPMASTER
INSTALLATION INSTRUCTIONS RIDGEMASTER PLUS CAUTION Before beginning installation read all general guidelines, special notes and installation steps thoroughly and be sure to check and follow all your local
More informationCONTENTS. Transitions Board and Batten Vertical Installation... 10,11
INSTALLATION MANUAL CONTENTS Important Notes... 2-4 Weather Protective Barriers... 2 Storage and Transportation... 2 Tools and Equipment... 2 Fastener Choices... 3 Wall Preparation... 3,4 Flashing... 4
More informationGambrel Barn Construction Manual 8x8 through 16x24 Units
Gambrel Barn Construction Manual 8x8 through 16x24 Units Tools Needed: Cordless drill (12V or higher) #2 square drive bit Hammer 6 step ladder Tape measure Square utility knife w/ blade & hook blade Little
More informationCurium 19H Installation Instructions & Parts List
Curium 19H Installation Instructions & Parts List Illustration Curium 19H Right Hand Page 1 of 15 01/07/2016 Revision 2.1 IMPORTANT This shower screen / enclosure must be installed by suitably qualified
More informationBest Buy Metals Toll Free / Phone / Fax
DETAIL MANUAL for Vertical Seam Best Buy Metals Toll Free 1-800-728-4010 / Phone 423-479-6382 / Fax 423-728-3066 www.bestbuymetals.com Vertical Seam Roofing Panels Fig. 2 Vertical Seam Has 1-3/4" high
More informationPolyCarb has good resistance to many chemicals. Some chemicals may harm the PolyCarb sheets. Contact us when in doubt about any chemical.
Polycarbonate Panels This manual provides the basic information for working with and installing PolyCarb sheets. Due to their hollow core, prior preparation is needed before the actual installation, with
More information10 Octagon Cedar Gazebo Assembly Instructions
10 Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/22/09 10 Cedar Gazebo Assembly Instructions
More informationSafety Glasses Safety Gloves Ladders Measuring Tape Spirit Level String Line. Tin-Snips Rivet Gun Caulking Gun Silicone Socket Set
BEFORE YOU START Carefully read these instructions and refer to them constantly during each stage of construction. If you do not have all the necessary tools or information, contact Stratco for advice.
More informationBlokes Shed INSTALLATION INSTRUCTIONS Custom Design & Build. Nationwide Delivery
Blokes Shed 10 Year Guarantee On Sanders workmanship Made in NZ Using NZ timber supplies 40+ Years Experience In business since 1975 Professional Install Available NZ wide Nationwide Delivery Available
More informationInstallation Manual SOLID CORE SIDING
Installation Manual SOLID CORE SIDING SOLID CORE SIDING Installation Information contained in this manual can be viewed in video form at: www.youtube.com/epbc CONTENTS Important Notes...2-4 Weather Protective
More informationFitting Instructions
Fitting Instructions = Actions. Red = Notes you must read before continuing. Grey = Only applies to canopies over 4m widths. Overview 1. Tools you will need. 2. What you will need to provide. 3. Description
More informationGeneral Instructions. Please retain product label and instructions for future reference 7X5 OVERLAP APEX
General Instructions 7X5 OVERLAP APEX x2 Please retain product label and instructions for future reference All building s should be erected by two adults Winter = High Moisture = Expansion Summer = Low
More informationRenaissance Pavilion. Assembly Manual
Renaissance Pavilion Assembly Manual Thank you for your purchase of this pavilion. Renaissance Pavilion Assembly Manual This manual is designed to simplify the assembly process, however we recommend having
More informationVinyl Gazebo Instructions
P a g e 1 Vinyl Gazebo Instructions 10 Vinyl Gazebo Shown Thank you for the purchase of your New Gazebo. Depending on the size of your Gazebo, installation can usually be completed in 1 to 2 days. These
More informationOptiLiner Banded Liner System Bi-Directional Banding
TOP LAYER UNFACED INSULATION ROOF SHEET ING LINER BOTTOM LAYER UNFACED INSULATION General Introduction The is designed to provide maximum thermal performance in preengineered metal buildings using Owens
More informationInstallation Instructions
Installation Instructions Building Design and Construction To ensure adequate performance and longevity, protect metal panels from potentially corrosive situations and materials. When treated lumber will
More informationTable of Contents. Installation Guide for Profile with Hidden Fasteners 3. Installation Steps 4, 5. Prestige Series Moldings 6, 7. Other Accessories 8
1 Table of Contents Page(s) Installation Guide for Profile with Hidden Fasteners 3 Installation Steps 4, 5 Prestige Series Moldings 6, 7 Other Accessories 8 Trims & Accessories 9 Eave Starters 10 Gableboards
More informationCurium 19.4H Installation Instructions & Parts List
Curium 19.4H Installation Instructions & Parts List Illustration Curium 19.4H Right Hand Page 1 of 21 30/06/2016 Revision 1.0 IMPORTANT This shower screen / enclosure must be installed by suitably qualified
More informationYWY M08 The new VELUX solution
YWY M08 The new VELUX solution VELUX roof windows and vertical window elements installed as a dormer in roof pitches between 42º and 52º YWY M08 is available as a double or triple unit and can be installed
More informationSANERI 3 º. Self-adhesive SBS-elastomer bitumen cap sheet
SANERI 3 º Self-adhesive SBS-elastomer bitumen cap sheet 0809 www.katepal.fi 06 EN 13707 Producer: KATEPAL OY P. O. Box 33 FI-37501 LEMPÄÄLÄ FINLAND Tel. +358 (0)3 375 9111 Fax +358 (0)3 375 0974 E-mail:
More informationEnsure there is reasonable access for materials and working space, ensure the shed site is level and consider the disposal of run-off water.
INSTALLATION GUIDE TM Flat Roof Homesheds THE POTTER BEFORE YOU START It is important to check your Local Government Authority requirements before the installation of your new Stratco Potter Flat Roof
More informationGABLE END CHIMNEY FITTING INSTRUCTIONS STANDARD LITESTACK CHIMNEY FITTING INSTRUCTIONS. HEALTH & SAFETY WARNING:
GABLE END CHIMNEY FITTING INSTRUCTIONS STANDARD LITESTACK CHIMNEY FITTING INSTRUCTIONS. HEALTH & SAFETY WARNING: THESE INSTRUCTIONS ASSUME THAT THE CHIMNEY IS BEING FITTED BY A PROFESSIONAL CONSTRUCTION
More informationAustin Standing Seam Awning Assembly and Installation Instructions. Assembly Instructions
Austin Standing Seam Awning Assembly and Installation Instructions Be sure to use safety glasses when assembling and installing the awning. Some metal parts may have sharp edges. Use work gloves to handle
More informationGuardian warm roof conversion system. Installation Guide
Guardian warm roof conversion system Installation Guide 2 www.guardianroof.co.uk Conservatory walls consist largely of glazed elements including windows and doors that may include structural mullions or
More information