Blokes Shed INSTALLATION INSTRUCTIONS Custom Design & Build. Nationwide Delivery

Transcription

1 Blokes Shed 10 Year Guarantee On Sanders workmanship Made in NZ Using NZ timber supplies 40+ Years Experience In business since 1975 Professional Install Available NZ wide Nationwide Delivery Available NZ wide Custom Design & Build Designed for your space Full Lining Packages Power, insulation & lining

2 Blokes Shed 2 Contents Foundations 3 Sub Floor 4 Floor and Deck 5 Walls 6 Roof Framing 7 Roof 8 Flashings 9 Doors and Window 10 Tools Required 11

3 Blokes Shed 3 Foundations 1. Set out piles according to the pile diagram above. The area in green is the shed. When location of piles has been established dig pile holes approximately 300 X 300 X Concrete in the piles making sure they are plumb, in line with each other and SQUARE. 3. Once the concrete has set use your straight edge and level to mark the height of the piles. 4. Cut piles to height.

4 Blokes Shed 4 Sub Floor 1. Lay the 100 X 100 ROUGH SAWN BEARERS across the piles and nail in place. 2. Begin laying the sub floor frames as shown above. On Skids 1. Lay the bearers directly on the ground. 2. Lay the sub floor framing on the skids/bearers. 3. Level the sub floor framing one section at a time using a straight edge and level. Place blocks between the skids and the subfloor framing to support and level the frames.

5 Blokes Shed 5 Floor 1. When the sub floor framing has been laid and nailed together attach the 100 X 50 ROUGH SAWN BRACES to the front and back (Shown in red). If the braces are not installed the sub floor will not be the correct size for the ply flooring. 2. Nail the ply flooring to the sub floor.

6 Blokes Shed 6 Walls It is important to remember the walls can only go together one way. All panels are labelled and have an arrow indicating the top. 1. Attach two corner panels first to provide bracing. Join together and fix panels to floor with 10g 75mm BUGAL HEAD SCREWS. 2. Ensure that the building paper is pulled all the way out and is not trapped between the panels.

7 Blokes Shed 7 Roof Framing 1. Space Truss (In blue) evenly and nail to top plate of exterior walls. 2. Attach 70 X 45 purlins to rafters (in red).

8 Blokes Shed 8 Roof 1. Lay roofing paper provided over the entire roof (in grey) allowing an overhang at the sides of the unit. 2. Lay in the roof.

9 Blokes Shed 9 Flashings 1. Fix corner battens x 4 (shown in blue). 2. Fix 150 X 25 ROUGH SAWN BARGES to the unit (shown in red). Do this on both sides, front and at the back of the unit. 3. Starting with the front and back barges first (in yellow above), cut and fix barge flashings. 4. When barge flashings have been fixed front and back attach the ridge cap.

10 Blokes Shed 10 Doors (and Window if provided) 1. Cut out the framing from the bottom of the door opening. 2. Remove the brace from the bottom of the door, insert door into opening and nail off. 3. The main door has a latch on the inside. Locate the latch and drill a hole in the top of the door frame so the door can lock. 4. Install the window making sure the front face of the window jamb is flush with the cladding. 5. Seal in the gap between the outside of the window jamb and the framing with silicone (not included) 6. Use the 90 X 30 PG DECKING down each side of the window to weatherproof

11 Blokes Shed 11 Tools Required 1. Spade 2. Straight Edge 3. Level 4. Chainsaw (optional) 5. Nail gun (optional) 6. Impact driver 7. Tec Screw Bit 8. 10g Hex bit 9. Drill 10. Skill saw 11. Hammer 12. Tape measure 13. Pencil 14. Square mm Drill Bit 16. Chalk Line 17. String Line 18. LH Tin snips 19. RH Tin snips 20. Sliding Bevel Review our products on Google: