Fan-Magnetic Rower MODEL: R 700 ENGLISH
|
|
- Shonda Manning
- 6 years ago
- Views:
Transcription
1 Fan-Magnetic Rower MODEL: R 700 ENGLISH
2 **Before staring to assemble the machine, please be sure to read below instructions first and follow the assemble steps. Warning: (). Due to the machine is heavy, it s strictly recommended for two people to operate the machine assembled. (). As the machine is heavy, so the polyfoam is requested to help you supporting the machine until assemble steps completed. Please don t thrown it away till machines completed assembled. The machine is packed by parts cartons, upper and down. When you open the upper carton, you will see the machine lying as below shown. Keep down part carton flat under the machine, so you can use it as a mat to keep machine clear till assembly finished. POLYFOAM(3) POLYFOAM(4) POLYFOAM() POLYFOAM()
3 Front stabilizer Main frame Rear stabilizer Saddle Adaptor Chest strap Upper slide track (F) Pedal(right) Connection pedal tube (F) Pedal(left) (J) Screw M8*6 (J) Washer M8 Tool M6 M5 - -
4 D HOW TO REMOVE STYLISH POLY-FOAM Open the carton, then you will see as left showing. Take out all the components, except the machine, then remove the POLYFOAM () and take out the components inside the polyfoam. Please put these components at side for further assemble. Put the POLYFOAM() back to it s original position, then turn the whole unit by 90 degree. (As shown). You are ready to go on for following assemble. E POLYFOAM() B HOW TO ASSEMBLE THE FRONT STABILIZER Equip the front stabilizer (B) onto main frame and tight it with screws(j)and washers (J). After equipped, turn the machine as the d irection of next figure 3 shown. A POLYFOAM() J J USE TOOL POLYFOAM() - -
5 HOW TO ASSEMBLE THE CONNECTION PEDAL TUBE After turn the main frame(a), remove the stylish poly-foam (3, 4) firstly. Equip the connection pedal tube (G) onto main frame (A) and using screws(j) to tight it. POLYFOAM(4) POLYFOAM(3) A A G J USE TOOL HOW TO ASSEMBLE THE SADDLE WITH PER SLIDE TRACK Equip saddle (E) onto upper slide track (D) as shown, t hen using screws(j) to tight upper slide track (D) with main frame (A). D E J A J D USE TOOL -3-
6 HOW TO ASSEMBLE THE REAR STABILIZER Pull up the upper slide track(d) and equipped rear stabilizer (C) on. Using screws (J) to tight rear stabilizer with upper slide track (D). J D C USE TOOL HOW TO ASSEMBLE AND ADJUST THE PEDAL Equip right pedal(f) onto connection pedal tube(g) and using screws(j), washers(j) to tight it. If you would like to adjust the pedal, please loosen the nut(f0) and knob(f9) first. After up and down adjustment for proper position, just tight them back. ** The same way to assemble left side pedal. A F0 J F9 USE TOOL G F J -4-
7 HOW TO ASSEMBLE THE MACHINE It s strictly recommend for two people operate when you would like to fold the machine to avoid any further injure happened. Loosen the knob(a4) then pull it down. Fold up the slide tracking as shown, then tight the knob. Please be noted to hold the slide tracking until the know is fixed tightly. The adaptor is requirement for console operation. A4 D HOW TO USE THE ADAPTOR Position Machine on consideration for convenience, using the adaptor, there is one adaptor hole located at the front of the machine. -5-
8 HOW TO MOVE THE MACHINE Move the front stabilizer has built-in transport wheels. Stand at the front of the machine and lift it up until the weight of the machine is transferred to the transport wheels. You can now easily move the machine to a new location. H TOOL 8M HOW TO ADJUST THE POSITION FOR CONSOLE/CONSOLE HOUSING AND PEDAL A The console angle is adjustable as shown. After proper position find, please using tool of 8mm to fix it. Pedal Strap Adjustment (). Put right foot into right pedal (F), tight the pedal strap(f3) after find proper position. (). The same way to adjust left side. F3 F -6-
9 HOW TO FIX PEDAL STRAP (). Tight the pedal strap(f3) after you find the fix position is proper for you. (). The same way to adjust left side pedal strap. F3 Notice about Adjustmentof Upper Slide Track (D) and Sliding Track (E) There are 3 pieces of screws (E9*pc and E3*pcs) as the diagram shown under the sliding track (E). Loosen the middle screw (E9) first and then adjust the other pieces of screws (E3) to be loose or tight depending personally. Lastly, tighten the middle screw (E9) to fix. TOOL 5M E3 E9 E3 E E D -7-
10 A44*6 A47 A43*3 E8 E5 C E7 E4 E E J -8- E3 E9 E6 E C F- F-3 F-4 F-3 J* A56* F-4 A45 F- F- F3* A3 F4 A48 A6 G3 F4 F G A53 F6 A58*4 F3 A A35 A57* L A3 F9* F0* F8* A A55*4 D G A3*4 A8*4 A5 A J*4 A5 L A6 J*8 A5 A8*4 J G4 J A8 A4 A8 A6 A5 A7 A A9 A30 A3 A49 A50 F5 A9 H4 A4 A3 F7*4 J A48 J G A0 A33 A*6 A3 A34 F- F*4 F*6 F A8 A30 A9 A7 A7 A A9 A46 B A4 A47 A6* A0 A4 A60* A A44*5 H H3 H A6 A40 A39 A43*3 H B A38 A4 A6 A54 A37 A36 A59* A5
11 P/N DESCRIPTION Q TY P/N DESCRIPTION Q TY A MAIN FRAME A53 FIX PLATE OF FRONT STABILIZER A SWIVEL AXIS A54 AXLE *39 A TRANSPORTATION WHEEL A55 SCREW M6* 4 A3 BUSH A56 BLOCK PLATE OF SLIDE TRAIL A4 KNOB A57 PLATE 0*60*4T A5 FEET END CAP A58 BUMPER 4 A6 SCREW M8*6 A59 NUT M6 A7 SCREW M6*0 A60 BRACKET A8 SCREW 5/3 */ 8 A6 SCREW M6*40 A9 SCREW M6*90 A6 RUBBER STINGER A0 NUT M6 B FRONT STABLILZER A CONSOLE TUBE B END CAP A SCREW 3/8 *3 3/4 * C REAR STABILIZER A3 BUSH 38*3/8 4 C END CAP A4 NUT 3/8 D PER SLIDE TRACK 500MM A5 PLASTIC PULLEY E SADDLE LS-E9 A6 NUT 3/8*6(UNF) E SLIDING TRACK 80MM A7 NUT 3/8*6(UNF) E SCREW M8*40 4 A8 BELT 350J6 E3 SCREW M6*5 A9 PULLEY E4 PULLEY SEAT A0 TENSION BELT E5 WHEEL 6 A MAGNETIC 6*5T 6 E6 AXLE A NUT 3/6 E7 WASHER 5* 3*.5T 6 A3 SPRING BOX E8 SCREW M5*0 6 A4 WASHER E9 SCREW M6*0 A5 C CLIP S0 F PEDAL(R) A6 PULLEY SEAT PLATE F- BOTTOM COVER OF PEDAL(R) A7 SCREW M5*0 3 F- SCREW M6*8 4 A8 SCREW M5*6 4 F-3 CUSHION PAD(R) A9 BEARING 60ZZ F-4 FRONT COVER OF PEDAL(R) A30 WASHER M6 F PEDAL(L) A3 SCREW M6* F- BOTTOM COVER OF PEDAL(L) A3 BELT WHEEL 6 F- SCREW M6*8 4 A33 ONE WAY BEARING(FC06) F-3 CUSHION PAD(L) A34 BEARING(HK0) F-4 FRONT COVER OF PEDAL(L) A35 AXLE F3 PEDAL PLATE (R) A36 TENSION CABLE 600MM F4 PEDAL PLATE (L) A37 HANDLE F5 PEDAL BOTTOM SEAT (L) A38 SPONGE HDR 30*3T*5MM F6 PEDAL BOTTOM SEAT (R) A39 END CAP /4 F7 BUSH (T0F) 4 A40 COVER OF TENSION BELT (R) F8 SCREW M5*8 A4 COVER OF TENSION BELT (L) F9 KNOB 3/8 A 4 CHAIN COVER(R) F0 NUT 3/8 A43 SCREW 3/6 */ 6 F WASHER 3/8 *T* 3 4 A44 SCREW 3/6 *5/8 F CLAMP OF MESH BELT 6 A45 CHAIN COVER(L) F3 PEDAL COVER A46 FRAME OF TENSION BELT F4 SCREW 5/3*5/8 6 A47 SCREW M5* G CONNECTION PEDAL TUBE A 48 SCREW M8*6 4 G SCREW M8*0 A49 SCREW /8 */ 4 G NUT M8 A50 COVER OF SPRING BOX G3 SCREW 3/6 * /4 A5 HANDLE FIXED SEAT G4 BUMPER A 5 SCREW M5*45 H CONSOLE -9-
12 P/N DESCRIPTION Q TY P/N DESCRIPTION Q TY H SENSOR WIRE H MOTOR H3 DC WIRE H4 SENSOR WIRE J SCREW M8*6 6 J WASHER 8 8 K L ADAPTOR CHEST STRAP L SCREW M8*0 L WASHER 8-0-
13 --
14 MANUAL mode USER SELECT U0-U4 SELECT SEX OF MALE OR FEMALE SELECT AGE SELECT HGT SELECT WGT RESET 3SEC. TO RESET OR OR OR OR OR SELECT MANUAL SELECT LOAD L-L6 SELECT TIME SELECT DISTANCE SELECT PROGRAM SELECT WATT SELECT USER SELECT H.R.C SELECT RACE OR OR OR OR SELECT CALORIES SELECT PULSE SELECT STROKES START/STOP OR OR OR --
15 PROGRAM mode USER SELECT U0-U4 SELECT SEX OF MALE OR FEMALE SELECT AGE SELECT HGT SELECT WGT RESET 3SEC. TO RESET OR OR OR OR OR SELECT MANUAL SELECT LOAD SELECT PROGRAM SELECT P=> L-L SELECT P7=> L-L0 SELECT WATT SELECT USER SELECT H.R.C SELECT RACE SELECT P=> L-L0 SELECT P3=> L-L0 SELECT P4=> L-L8 SELECT P5=> L-L8 SELECT P6=> L-L0 SELECT P8=> L-L8 SELECT P9=> L-L0 SELECT P0=> L-L8 SELECT P=> L-L0 SELECT P=> L-L7 OR OR OR SELECT TIME SELECT DISTANCE SELECT CALORIES SELECT PULSE SELECT STROKES START/STOP OR OR OR OR OR -3-
16 WATT mode USER SELECT U0-U4 SELECT SEX OF MALE OR FEMALE SELECT AGE SELECT HGT SELECT WGT RESET 3SEC. TO RESET OR OR OR OR OR SELECT MANUAL SELECT WATT SELECT TIME SELECT DISTANCE SELECT PROGRAM SELECT WATT SELECT USER SELECT H.R.C SELECT RACE OR OR OR OR SELECT CALORIES SELECT PULSE SELECT STROKES START/STOP OR OR OR USER mode USER SELECT U0-U4 SELECT SEX OF MALE OR FEMALE SELECT AGE SELECT HGT SELECT WGT RESET 3SEC. TO RESET OR OR OR OR OR SELECT MANUAL SELECT LOAD L-L6 SELECT TIME SELECT PROGRAM SELECT WATT SELECT USER SELECT H.R.C SELECT RACE START/STOP (START) START/STOP (STOP) OR OR OR REPEATING THESE OPEARTION TILL COMPLETING THE SETTING OF 6 RANGES SELECT DISTANCE SELECT CALORIES SELECT PULSE SELECT STROKES START/STOP OR OR OR -4- OR
17 H.R.C mode USER SELECT U0-U4 SELECT SEX OF MALE OR FEMALE SELECT AGE SELECT HGT SELECT WGT RESET 3SEC. TO RESET OR OR OR OR OR SELECT MANUAL SELECT TIME SELECT DISTANCE SELECT PROGRAM SELECT WATT SELECT USER SELECT H.R.C SELECT RACE SELECT 55% SELECT 75% SELECT 90% SELECT TAG SELECT PULSE OR OR OR OR OR SELECT CALORIES SELECT STROKES START/STOP OR OR -5-
18 RACE mode USER SELECT U0-U4 SELECT SEX OF MALE OR FEMALE SELECT AGE SELECT HGT SELECT WGT RESET 3SEC. TO RESET OR OR OR OR OR SELECT MANUAL SELECT SPM/TIME/500M SELECT DISTANCE SELECT PROGRAM SELECT WATT SELECT USER SELECT H.R.C SELECT RACE START/STOP OR OR OR -6-
Assembly. Item G7 Qty 1. Item D4. M10 x 55 mm Allen Bolt. Item D5. Qty 2. Item E13 Qty 4 M10 Flat Washer. Item B18. M8 x 30 mm Allen Bolt (Black)
ACCESSORY FITMENT LIST These are all the accessories you will need to complete the assembly of your product. The following accessories are supplied in a pack and should be checked before attempting assembly
More informationTable of Contents. Product Safety Part Drawing & Contents Hardware & Tools Assembly Adjustment
Owner s Manual A Table of Contents Product Safety.. 01. Part Drawing & Contents..... 02. Hardware & Tools.. 03. Assembly... 04. Adjustment... 10. Trouble Shooting & Maintenance.. 11. Computer... A. Warm
More informationSole Fitness E95 Elliptical Trainer TurnKey Delivery and Setup Training
Sole Fitness E95 Elliptical Trainer TurnKey Delivery and Setup Training Delivery Requirements Ground delivery Inside delivery to customer-specified location Unpack and assemble machine, and remove packing
More informationStar Trac Turbo Trainer Assembly & Setup
Star Trac Turbo Trainer Use the following procedures to unpack and assemble your Turbo Trainer manufactured by Star Trac. UNPACKING AND PARTS LIST Position the shipping carton so the Heavy End logo is
More informationAX1001. Smith/Functional training Combo-free weight ASSEMBLY INSTRUCTIONS
AX1001 Smith/Functional training Combo-free weight ASSEMBLY INSTRUCTIONS EXPLODED DIAGRAM 83 84 84 85/86 87 87 88 89 90 91 62 64 64 64 64 64 64 65 65 65 65 66 66 65 66 66 65 63 63 66 67 68 55 66 66 70
More informationOBE165AF Elliptical Cross Trainer
OBE165AF Elliptical Cross Trainer TABLE OF CONTENTS PRODUCT SAFETY.. 01. PART DRAWING & CONTENTS..... 02. HARDWARE & TOOLS.. 04. ASSEMBLY.. 05. FOLDING.. 11. ADJUSTMENT.. 12. TROUBLE SHOOTING & MAINTENANCE
More informationS48-L12-SC AND G48-L12-GC STEEL PORTA-DOCK S82 SC 6 X 12 PLATFORM AND G82 GC 6 X 12 PLATFORM
PAGE 1 OF 6 PORTA-DOCK, INC. S48-L12-SC AND G48-L12-GC STEEL PORTA-DOCK S82 SC 6 X 12 PLATFORM AND G82 GC 6 X 12 PLATFORM Thank you for purchasing our product! *Please read these instructions and follow
More informationPORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12
Page 1 of 7 PORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12 *For Beige Decking Add the Letter B to Model* Thank you for purchasing out product! *Please read these instructions and follow
More informationAssembly Instructions: AM-10 Hand & Foot Cycle Early Intervention Part #: 50-HFC-0105
Assembly Instructions: AM-10 Hand & Foot Cycle Early Intervention Part #: 50-HFC-0105 Refer to the following instructions on how to assemble your tryke. Study the instructions carefully before beginning
More informationOWNERS MANUAL MODEL F660 HIP SLED
OWNERS MANUAL MODEL F HIP SLED QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will guarantee your complete
More informationShapeoko XXL Assembly Guide
Shapeoko XXL Assembly Guide 04/27/2016 XXL Packing LIst Item Qty Description Y-Carriage (left) 1 Y-Carriage (right) 1 X/Z Assembly 1 40 Rail 3 1 rail has mounting holes for controller Wasteboard Half 2
More informationThank you for purchasing out product! *Please read these instructions and follow them step by step. *
Page 1 of 7 AD17 AA DS 4 X 16 T12 Thank you for purchasing out product! *Please read these instructions and follow them step by step. * STEP 1. Slide two support posts (REF. # 24) into the two outside
More informationImportant Safety Information
HM-30 NC 30B HOME GYM Important Safety Information Please keep this manual in a safe place for reference.. It is important to read this entire manual before assembling and using the equipment. Safe and
More informationExploded Diagram /1/23
& Exploded Diagram www.firstdegreefitness.com 2018/1/23 Upper Frame Assembly A048 Seat Assembly A078 60806 60809 10097 A039 Lower Frame Assembly 10041 1 Nyloc Nut M10 10082 3 Washer M10x21x2 10097 1 Nut
More informationHardware and Components:
Hardware and Components: (A) 5/16 x 2 Hex Bolt (B) 5/16 x 2-1/4 Hex Bolt (C) 5/16 x 2-1/2 Hex Bolt (D) 4X 5/16 x 3/4 Hex Bolt (E) 4X 5/16 x 1-1/4 Hex Bolt (F) 11X 5/16 Flat Washer (G) 12X 5/16 Nylock Nut
More informationA59 APD & A86 CPD 5'X 16' SW ALUMINUM PORTA-DOCK
Page 1 of 5 PORTA-DOCK, INC. A59 APD & A86 CPD 5'X 16' SW ALUMINUM PORTA-DOCK *For Beige Decking Add the Letter B to model* Thank you for purchasing our product! *Please read these instructions and follow
More informationHOME GYM Owner s Manual
HOME GYM Owner s Manual Content Content-------------------------------------------------------------1 Safety precautions----------------------------------------------------2 Assembly instruction-------------------------------------------------3-12
More informationOlympic Bench Model 6600
Olympic Bench Model 6600 IMPORTANT SAFETY INSTRUCTIONS TKO Fitness products are designed and manufactured to the highest standards in order to provide you with years of great workouts. We proudly stand
More informationRemoving the Z-Axis lead screw
Page 1 of 8 TITLE: Sabre Z-Axis Lead Screw Replacement Procedure Gerber FastFact #: 5048 Supplied by: Gerber Hardware Support Last Modified: June 14, 2007 Summary: Tools used: The following procedure explains
More informationLifeGear G1 /HOME GYM ITEM NO.: 63100
LifeGear G1 /HOME GYM ITEM NO.: 63100 OWNER S MANUAL IMPORTANT: Read all instructions carefully before using this product. Retain this owner s manual for future reference. The specifications of this product
More informationPHONE: FAX:
Models: SB-12600, SB-12600C, SB-12601, SB-12680, SB-126801, SB-12682, SB-12683, SB-12720, SB-12720C, SB-12760 1... BI-32018... Paper Bag, type SUB-3, 3 pack 2... BI-5554431... Handle Tube, w/ grip 2...
More information25-200H. 12 Planer / Jointer. with Helical Cutterhead. Parts List.
25-200H 12 Planer / Jointer with Helical Cutterhead 4001824 Parts List www.rikontools.com CABINET ASSEMBLY PARTS EXPLOSION & PARTS LIST KEY NO. DESCRIPTION KEY NO. DESCRIPTION 1 Pan Head Screw M6x12 P25-200H-1
More informationSECTION 9: PARTS. Table Breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION
SECTION 9: PARTS Table Breakdown 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 23 25 17 26 27 8 1 P0675001 CAP SCREW M8-1.25 X 30 15 P0675015 SUPPORT BLOCK 2 P0675002 TABLE SUPPORT BLOCK
More informationThe Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 )
P/N: 001-7057 Rev ( /0 ) The Bowflex Revolution XP Home Gym Assembly Instructions 2 Table of Contents Before You Start... 2 Tools You Will Need / Hardware Contents... 3 Box Contents... 6 Assembling Your
More informationOWNER S MANUAL. Elliptical Trainer
Elliptical Trainer! 1317.5 101016 Read all instructions carefully before using this product. Retail this owner s manual for future reference. The specifications of this product may vary from this photo,
More informationInstallation instructions, accessories. TV receiver, digital
Installation instructions, accessories Instruction No 30756561 Version 1.1 5 Part. No. 30756181, 30756569 TV receiver, digital Volvo Car Corporation TV receiver, digital- 30756561 - V1.1 Page 1 / 36 Equipment
More informationSECTION 9: PARTS. Main Breakdown -36- Model G5394 (Mfd. Since 11/08)
SECTION 9: PARTS Main Breakdown 105 137 136 113-1 113 141 140 113-2 113-3 111 113-4 114 135 143 144 101 121-1 -1 116 147-1 121-2 115 120 121 107 108 164 162 160 158 138 109 127 126 160 158 123 127 123
More informationExploded View Saw Base - Model 7060 Semi-Automatic Cut-Off Band Saw
Exploded View Saw Base - Model 7060 Semi-Automatic Cut-Off Band Saw 136 137 135 134 132 131 133 113 114 115 117 116 118 119 120 121 79 78 77 107 108 65 76 110 109 66 10 9 6 11 5 4 8 7 75 74 73 72 111 112
More informationElectric Skein Winder
Electric Skein Winder Assembly and Use Package Contents 1 - Triangular Body (w/ motor) 1 - Cross Arm 1 - Left Foot (w/ yarn guide) 1 - Right Foot 1 - Adjustable Finger (w/ yarn clip) 3 - Adjustable Fingers
More informationABM International, Inc. Navigator Assembly Manual
ABM International, Inc. 1 1.0: Parts List Tablet (Qty. 1) Tablet mount (Qty. 1) NOTE: Mount may appear and operate different then image below Control Box (Qty. 1) Motor Power Supply (Qty. 1) 2 X-axis motor
More informationMaintenance manual. 1. Check height seat adjusment
1. Check height seat adjusment 1.1 By control hand lever seat, seat must always going down when person is sitting on it. 1.2 Squeaky noise when control hand lever seat? 1.1 1.2 2. Check table height adjustment
More informationBRM * This item is for consumer use only and it is not meant for commercial use.
BRM 10 * This item is for consumer use only and it is not meant for commercial use. OWNER S MANUAL General Information Safety Before you undertake any exercise program, please be sure to consult with your
More informationExploded Diagram
Exploded Diagram www.firstdegreefitness.com 1 2017/9/14 A009 Complete Tank Assembly Computer Stalk Assembly Main Frame Assembly A085 Belt Pulley / Main Drive Assembly A069 Handle Assembly A245Complete
More informationWARNING: THERE IS ALWAYS A DANGER OF INJURY WHEN
Assembly Instructions: AM 10 Hand & Foot Cycle Early Intervention Part #: 50 HFC 0105 Refer to the following instructions on how to assemble your tryke. Study the instructions carefully before beginning
More informationTS4001. Model # 10 inch Table Saw addendum SETUP & OPERATION MANUAL
SETUP & OPERATION MANUAL Features Powerful 13 amp motor Cast aluminum work table Riving knife Anti-kickback pawls Includes: 10 in. 24 tooth tungsten carbide tipped saw blade Rip fence Miter gauge Push
More informationPFT CABLE GYM INSTRUCTION MANUAL
PFT CABLE GYM INSTRUCTION MANUAL QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will guarantee your
More informationINVENT3D Printer Kit Disassembly Instructions
INVENT3D Printer Kit Disassembly Instructions Version 6 AST2 10/26/16 1 I. General Disassembly Instructions Use the case layer drawings to ensure that components are stored in the appropriate location
More informationTriplex Instructions for Packing and Unpacking
2-8-8-2 Triplex Instructions for Packing and Unpacking It is recommended that you review all these instructions before removing the engine or tender from the poly foam container. www.mthtrains.com Table
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PARTS REQUIRED Single QuickStand Lite Parts A (1) Lower Arm A B C D B (1) Upper Arm C (1) Base D (1) Base Plate E (1) M8 Dynamic Arm Long F (1) Clamp Bracket G H (1) VESA Plate
More informationModel W1739 Variable Speed Planer Moulder Manual Insert
Model W1739 Variable Speed Planer Moulder Manual Insert READ and understand this W1739 manual insert and the W1693 instruction manual before using this machine. Ignoring this warning may lead to serious
More informationTo install new top weight plate bushings in G7 strength units.
1/5 PURPOSE To install new top weight plate bushings in G7 strength units. RE-WORK PARTS REQUIRED - ZMS4000424 Top Weight Plate Bushing (Quantity 4 per machine). - Matrix Top Weight Plate Bushing Removal
More informationAndyMark DART 12.
AndyMark DART 12 Part Number Description QTY These Parts Are Pre-Assembled by AndyMark am-0031 Bearing, 3/16"ID (R3) 1 am-0209 Bearing, 3/8"ID 1614ZZ 2 am-1028 Screw, #10-32x3/8 Pan Head Philips 8 am-1121
More informationCode Product Qty 1 Top Vertex 3 2 Hot End Housing 1 3 Bottom Vertex 3 4 Print Platform Lock 3 5 End Stop Holder 3 6 Filament Feeder Motor Bracket 1 7
List of Parts Code Product Qty 1 680mm Extrusion 3 2 Power Supply 1 3 240mm Extrusion 9 4 42mm Nema 17 Stepper Motor 3 5 Slider-Hotend Connecting Rod 6 6 48mm Nema 17 Stepper Motor 1 7 Linear Rail with
More informationINSTALLATION GUIDE 8IWBM-EL. phone: (02) fax: (02)
INSTALLATION GUIDE 8IWBM-EL www.gilkon.com.au email: sales@gilkon.com.au phone: (02) 99140900 fax: (02) 99140901 CONTENTS 1. DISCLAIMER Page 2 2. WARNINGS & SAFETY INSTRUCTIONS Page 3 3. PACKAGE CONTENTS
More informationSpecial Z-Axis Ballscrew Replacement
To replace Z-axis ballscrew without removing X-axis components When rebuilding an OmniTurn slide, all the precision components are replaced. The tooling plate and saddle are removed to gain access to the
More informationTOYOTA MOTOR EUROPE CA Products Division Tel : Fax :
TOYOTA MOTOR EUROPE CA Products Division Tel : + 32 2 745 26 77 Fax : + 33 2 745 26 99 Ordering part numbers Comments Part Numbers Wooden floor one hatch PZ449-D3C42-11 one hatch with carpet PZ449-D3C42-01
More informationSTRATA STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL
STRATA STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will
More informationSECTION 9: PARTS Cabinet & Base
SECTION 9: PARTS 5 5-1 48 3 75 90 49 4 91 333 46 47 30 89 88 2 34 33 37 36 78 35 32 326 316 49 42 45 83 84V2 43 1 7 8 9 12 87 10 11 Cabinet & Base 31 17 20 40 39 136 41 135 85 86 8 28 26 18 19 21 19 370
More informationNancy s Knit Knacks LLC 4 Yard Option Upgrade Kit Assembly Instructions and User Manual
Nancy s Knit Knacks LLC 4 Yard Option Upgrade Kit Assembly Instructions and User Manual Thank you for purchasing our 4 Yard Option (4YO) Upgrade Kit. To install this upgrade you are simply going to assemble
More informationFree Wheelchair Mission GEN 2 Assembly
Free Wheelchair Mission GEN 2 Assembly This guide contains instructions detailing how to assemble your GEN 2. Written By: Garrett Goff ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 TOOLS: 10mm Wrench
More informationParts Manual for MODELS: ZKH52222 ZKH52252 ZKH61252
Parts Manual for MODELS: ZKH52222 ZKH52252 ZKH61252 Professional Quality Lawn Care Equipment since 1945 THIS MANUAL INCLUDES UPDATES ON PAGES 6,10, & 20. Yazoo/Kees Power Equipment policy is to improve
More informationINSTRUCTION MANUAL AND PARTS LIST MODEL 14-10
VERTICAL BAND SAWS INSTRUCTION MANUAL AND PARTS LIST MODEL 1-10 DAKE/PARMA WHEN ORDERING PARTS GIVE COMPLETE SERIAL NUMBER OF MACHINE GIVE PART NUMBER AND NAME GIVE AMOUNT REQUIRED Unless the above data
More informationPARTS Stand Breakdown
PARTS Stand Breakdown 35-5 35-2 35-4 63 1 2 3 4 5 35-1 35-3 36 37 38 39 35 34 33 32 30 28 6 7 8 21 29 23 22 27 26 25 24 42 43 44 45 46 47 9 10 62 61 60 51 11 59 19 18 12 12 13 58 14 57 15 56 55 54 53 52
More informationOperating Instructions and Parts Manual. 10 x 16 Horizontal Band Saw Models J-7020, J-7040
Operating Instructions and Parts Manual 10 x 16 Horizontal Band Saw Models J-7020, J-7040 JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-414472 Ph.: 800-274-6848 Revision C2 03/2014 www.jettools.com
More informationWARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. WARNING. Ranger XP Door Kit
REVISION 04 November, 20 2018 Ranger XP Door Kit Prior to installation, please verify if a revised version of this instruction sheet is available on Knowledge Center. The following symbols may be used
More informationSERVICE MANUAL & PARTS LIST MODEL: MC400E
First Edition: February SERVICE MANUAL & PARTS LIST MODEL: MC00E PARTS LIST MODEL: MC00E 0 0 MODEL: MC00E KEY PARTS NO. NO. DESCRIPTION 0 0 0B0 000 0A0 0A0 000 000 0 000 0 0000 0000 000 00 0 0 00 A0 0B0
More informationUsage and Assembly Instructions
Instructions #1037447 Product #795234 Revision D Usage and Assembly Instructions Rear Fork (Buttstock) Rear Fork Lock Knob Rail Lock Knob Front Fork (Forend) Rails Tilt Friction Knob Rail Extension Locks
More informationINSTRUCTION MANUAL LEG PRESS OPTION OF ELITE GYM
INSTRUCTION MANUAL LEG PRESS OPTION OF ELITE GYM QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will
More informationSHERLINE Mill Digital Readout
SHERLINE Mill Digital Readout P/N 8100 (Inch) Digital Readouts in the modern machine shop Digital readouts are popular on full-size shop mills because they make the life of a machinist much simpler. They
More informationF i t t i n g t h e N e w L a n d i n g G e a r t o Y o u r S k y J i b V 1
F i t t i n g t h e N e w L a n d i n g G e a r t o Y o u r S k y J i b V 1 1 P a r t s L i s t : S t a n d a r d L a n d i n g G e a r U p g r a d e Product Code Parts + Spares Product Code Parts + Spares
More informationHardware and Components:
Hardware and Components: (A) 4X 5/16 x 1 Carriage Bolt (B) 2X 5/16 x 2-1/4 Carriage Bolt (C) 2X 5/16 x 3-1/4 Hex Bolt (D) 2X 5/16 x 3/4 Hex Bolt (E) 2X 5/16 x 1-1/4 Hex Bolt (F) 5/16 x 2-1/4 Hex Bolt (G)
More informationFBX1104P FBX1104 FBX1106P FBX1106
FBX1104P FBX1104 FBX1106P FBX1106 Second edition : September 2004 No. 040037 INTRODUCTION Thank you for your purchasing Kansai Special's FBX Series. Read and study this instruction manual carefully before
More informationTRAILMATE METEOR ASSEMBLY MANUAL
TRAILMATE METEOR ASSEMBLY MANUAL The Trailmate Meteor recumbent has been designed for easy assembly. This means more time to enjoy the smooth ride with single speed, 3 speed coaster brake and 21 speed
More informationReplacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C)
Follow the instructions below to replace the reciprocator in the SWF Compact series machines. The tools required can be found in the tool kit that came with the machine. Preparation 1. First, place the
More information3 in 1 (Lawn mower/aerator/raker)
3 in (Lawn mower/aerator/raker) CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. Safety Assembly Operation Maintenance Parts TABLE OF CONTENTS
More informationIntercooler Shroud and Belt Cover for WRX
Intercooler Shroud and Belt Cover for 2015+ WRX 2016-05-18 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation
More informationM2 Assembly. M2 Sub-Assemblies mm Belt Sub-Assembly mm Belt Sub-Assembly Spider Sub-Assembly... 4
M2 Assembly Table of Contents M2 Sub-Assemblies... 3 630mm Belt Sub-Assembly... 3 702mm Belt Sub-Assembly... 3 Spider Sub-Assembly... 4 Idler Bolt Sub-Assembly... 8 Y Motor Sub-Assembly... 9 X Motor Sub-Assembly...
More informationSTRATA STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL
STRATA STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will
More informationHYDRAULIC CONTROL DETAILS PARTS LIST
Always give model number, serial number and part number when ordering repair parts. HYDRAULIC CONTROL DETAILS PARTS LIST REF NO. PART NUMBER DESCRIPTION 1 101939 Hydraulic Tank 2 101940 Hydraulic Tank
More informationSerial Number Location
GL/GLX STRENGTH TRAINING SYSTEM OWNERS MANUAL Serial Number Location SERIAL 3 4 5 7 8 Record your Serial number and purchase date here: S/N DATE: DEALER: Model No. BCG-GL BODYCRAFT is a division of Recreation
More informationset of safety brace steel cable draw-up gate kpl
0324101 7108020 8208100 Order-nr. Description Number 0324101 safety brace steel cable draw-up gate 2 7108020 hexagon-head tap bolt M8x20 galv. 2 8208100 hexagon nut M8 galv. 2 set of safety brace steel
More informationMachine Quilting Frame assembly, and instruction manual
Machine Quilting Frame assembly, and instruction manual Table of Contents Parts List................. Pg. 2 Step 1 - Legs............... Pg. 4 Step 2 - Lower Leg Brace....... Pg. 5 Step 3 - Frame Ends..........
More informationAssembly, Use and Care Instructions
Assembly, Use and Care Instructions Product #336677 Instruction #1068318 Rev. F Thank you for purchasing a Caldwell Lead Sled DFT 2. The Lead Sled DFT 2 comes to you partially assembled. It will require
More informationSection D ACCELERATOR
Section D ACCELERATOR 1D Index No. Part No. Description 1. 47-021476-001 Ball Accelerator Box 2. 11-051019-001 Hex Hd. Cap Screw (10 mm x 25 mm) 3. 11-052018-001 Flat Washer (10.5 mm x 21 mm x 2 mm) 4.
More informationHydrostatic Zero-Turn Commercial Riding Mower
Hydrostatic Zero-Turn Commercial Riding Mower Turf Equipment MODEL 20HP Enforcer 44 22HP Enforcer 48 23HP Enforcer 54 ILLUSTRATED PARTS LIST TABLE OF CONTENTS Frame Assembly..................................
More informationAnti-Chattering Retrofit Assembly
Anti-Chattering Retrofit Assembly Please follow through these instructions carefully and thoroughly. If you have questions, feel free to contact a Bend-Tech service representative at our office 651-257-8715
More informationRPS. XR Front Drive Updates CORPORATION
FACTORY CAT 1. To start a replacement of the XR Front Wheel Drive, make sure the machine is on level ground with the rear wheels chocked and always disconnect the batteries. 2. Locate the Positive and
More informationAM8 Printer A metal frame for your Anet A8 By Pheneeny v1.0 April 20, 2017
AM8 Printer A metal frame for your Anet A8 By Pheneeny v1.0 April 20, 2017 Please read this entire document before printing parts or building this frame Disclaimer: This guide is for informational purposes
More informationTABLE OF CONTENTS DESCRIPTION. Safety Instructions Assembly Operation... 7
TABLE OF CONTENTS DESCRIPTION PAGE Warranty... 1 Safety Instructions... 2 Assembly... 3 Operation... 7 #360 Grain Cleaner Drawings... 8 #360 Grain Cleaner Parts List... 10 Utility Auger Option Drawing...
More informationParts Manual for: MODELS / I.D. : / ZTH5223A / ZTH5225A / ZTH6125A
Parts Manual for: MODELS / I.D. : 968999153 / ZTH5223A 968999154 / ZTH5225A 969999155 / ZTH6125A Husqvarna policy is to improve its products whenever it is possible and practical to do so. In an effort
More informationFitWork Walkstation Series 7 AdjusTables
FitWork Walkstation Tools Required: #2 Phillips Bit with Extension Page 1 of 20 A7TG660606H A7TR663232H FitWork Walkstation 4mm Hex Head Bit A7TG660632H A7TR383030H www.details-worktools.com A7TG663206H
More informationCATALOG OF REPLACEMENT PARTS
The Choice of Experience CATALOG OF REPLACEMENT PARTS MODELS 909A 919A 909E 919E 909M 919M SLICERS EFFECTIVE MARCH 2009 - 2 - Table of Contents 5 ELECTRICAL COMPONENTS (909A & 919A) 7 ELECTRICAL COMPONENTS
More informationCOMMERCIAL MOWERS PARTS MANUAL FOR: MODELS: ZKH52221 ZKH52251 ZKH61221 ZKH61251
PARTS MANUAL FOR: COMMERCIAL MOWERS MODELS: ZKH52221 ZKH52251 ZKH61221 ZKH61251 FD KEES POWER EQUIPMENT, L.L.C. 700-800 PARK AVENUE BEATRICE, NEBRASKA, U.S.A. 68310 PRINTED IN USA MANUAL NO.-102935 REV.
More informationOperating Instructions and Parts Manual SLT-1100 Jumbo Scissor Lift Table
Operating Instructions and Parts Manual SLT-1100 Jumbo Scissor Lift Table JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-140780 Ph.: 800-274-6848 Revision B1 05/2014 www.jettools.com Copyright
More informationMANUAL REV. 03 (11/26/01)
Parts Manual MANUAL 539105906 REV. 03 (11/26/01) Models: 968999175 / ZTH7226KOA 968999180 / ZTH5221KAA 968999181 / ZTH5223KAA 968999182 / ZTH5223KOA 968999183 / ZTH5223KOLA 968999184 / ZTH5225KOA 968999185
More informationThank you for purchasing our product! *Please read these instructions and follow them step by step.*
07/07/08.rev1 PAGE 1 OF 11 601AL VERTICAL 60120VL LIFT W/CHAIN DRIVE WINCH Thank you for purchasing our product! *Please read these instructions and follow them step by step.* Step 1. Separate and group
More informationTROLLA LEAVY 97 CM Lawn sweeper
TROLLA LEAVY 97 CM Lawn sweeper Artikel nr.: 1008 EN Operating manual 014/1 Dear Customer, Congratulations on your new Trolla product. We hope you will enjoy it. Checkout with your new Trolla product may
More informationTABLE OF CONTENTS DESCRIPTION. Safety Instructions Assembly Operation... 7
TABLE OF CONTENTS DESCRIPTION PAGE Warranty... 1 Safety Instructions... 2 Assembly... 3 Operation... 7 #360 Grain Cleaner Drawings... 8 #360 Grain Cleaner Parts List... 10 Utility Auger Option Drawing...
More informationParts Catalog Admiral 28 Cylindrical Scrubber
Parts Catalog Table of Contents Front bounce protection (97116834)... 4 Wheel suspension (97103725)... 6 Chassis (97115422)... 8 (97114763)... 10 Steering (97073738)... 12 Seat bracket (97118616)... 14
More informationASSEMBLY PREPARATION IMPORTANT PRECAUTIONS
2 ASSEMBLY PREPARATION To ensure ease of product assembly, please take time to verify the size and quantities of all required assembly hardware. Use the itemized parts listing and hardware chart for reference.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Furniture Solutions: 68 Shipstation with Storage Shelf Model Numbers: PB001 (D9001, D9010N, D9021, D9030, D9032/D9033, D9098, RC4054) Introduction This document provides the Pitney
More informationODY-5. Odyssey Home Gym TABLE OF CONTENTS: Introduction - Pg. 1. Safety Precautions - Pg. 2. Assembly for ODY-5 - Pg. 3 - Pg. 18, Pg.
TABLE OF CONTENTS: Introduction - Pg. 1 Safety Precautions - Pg. 2 O W N E R S M A N U A L Assembly for ODY-5 - Pg. 3 - Pg. 18, Pg.20 Cable Adjustments - Pg. 19 Cable Mapping Diagram - Pg. 21 - Pg. 24
More informationSECTION 9: PARTS Jointer Breakdown
Model G0490/G0490X (Mfd. Since 8/12) -49-1 3 8 7 9 12 14 15 16 18 21 23 24 24 28 29 32 33 37 38 38 44 45 49 50 51 53 55 56 57 58 59 61 60 64 65 66 68 72 75 80 81 82 83 84 85 86 87 88 90 91 92 94 93 96
More informationAUTOMATIC ADVANCE MANUAL
AUTOMATIC ADVANCE MANUAL AVL Looms, Inc. 3851 Morrow Lane, Suite #9 Chico, CA 95928-8305 530 893-4915 530 893-1372 fax # info@avlusa.com www.avlusa.com Copyright 2009 TABLE OF CONTENTS Page # I. Parts.........................
More informationBig & Tall Executive Chair Assembly Instructions
Designed to be comfortable, and built to stay that way. Big & Tall Executive Chair Assembly Instructions 400 lbs Model 50106E PARTS A B C D Casters Quantity: 5 Star Base Quantity:1 Gas Lift Quantity: 1
More informationPlaner/Moulder Head USE helpers or power lifting equipment to lift this Planer/Moulder. Otherwise, serious personal injury may occur. To mount the Planer/Moulder head, do these steps: 1. Lay two 2x4 s
More informationSubwoofer. - F required in S40 with low cargo compartment floor - G always required in V50 - H required in V50 with low cargo compartment floor
1 of 26 Subwoofer 2 of 26 INTRODUCTION - NOTE! Read through the whole installation instruction before starting the work. - The front page gives the date of this edition and the edition it replaces - The
More informationINSTRUCTIONS AND PARTS LIST POWER HAMMER
INSTRUCTIONS AND PARTS LIST POWER HAMMER DAKE (Division of JSJ) 724 Robbins Road Grand Haven, Michigan 49417 616.842.7110 Phone 800-937-3253 616.842.0859 Fax 800-846-3253 Web: www.dakecorp.com E-mail :
More informationThe Queen Quilter Professional Quilters Kit Frame
The Queen Quilter Professional Quilters Kit Frame Assembly Instructions Table of Contents: Before you begin......................... Pg. 2 Wood parts............................. Pg. 3 Hardware..............................
More informationTRAKFAST REPAIR MANUAL DANGER TOOL DISASSEMBLY ALWAYS TAKE THE FOLLOWING PRECAUTIONS BEFORE ANY SERVICE OR ROUTING MAINTENANCE IS PERFORMED:
DANGER ALWAYS TAKE THE FOLLOWING PRECAUTIONS BEFORE ANY SERVICE OR ROUTING MAINTENANCE IS PERFORMED: REMOVE FASTENERS REMOVE FUEL CELL REMOVE BATTERY REMOVE THE MAGAZINE ASSEMBLY Loosen and remove knob
More information