TS4001. Model # 10 inch Table Saw addendum SETUP & OPERATION MANUAL
|
|
|
- Morgan Dorsey
- 6 years ago
- Views:
Transcription
1 SETUP & OPERATION MANUAL Features Powerful 13 amp motor Cast aluminum work table Riving knife Anti-kickback pawls Includes: 10 in. 24 tooth tungsten carbide tipped saw blade Rip fence Miter gauge Push stick Metal stand 10 inch Table Saw addendum SPECIFICATIONS 120 V ~ 60 Hz 13 A 5700 rpm Max. cutting height at 90 : 2-7/8 in. (73 mm) Max. cutting height at 45 : 2-5/8 in.(65 mm) Tilting range: 0 to 45 left Table dimensions: 26 in. x 17-1/2 in. (660 mm x 440 mm) Table height (on stand): 35-3/8 in. (900 mm) ETL certification Net weight: 43 lb. (19 kg) GENERAL INTERNATIONAL USA: 6243 Industrial Parkway, Whitehouse, OH (844) or (419) Canada: Unit Cariboo Road Burnaby, B.C., Canada V3N 4A3 (888) or (604) Model # TS4001 TS4001 man v.addendum
2 English assembly and setup REMOVE ALL THE PARTS FROM THE BOX Your table saw is fully assembled in the carton with the exception of the stand and some accessories Functional description. A Rubber foot (4 x) B Leg (4x) C Stand stretchers (2 x side, 1 x front & 1 x rear) D Short hex bolt, flat washer & nut (24 sets) E Stand skirt (2 x side, 1 x front & 1 x rear) F Long hex bolt, flat washer & nut (4 sets) G Switch with removeable key H Handwheel handle I Handwheel J Cable storage K Blade tilt lock lever L Front rail M Miter gauge N Blade guard O Riving knife P Anti-kickback pawls Q Table insert R Rip fence S 10 saw blade T Fence lock handle U Fence storage clip V Blade angle inticator W Push stick X Blade angle scale Fitting the blade s safety guard Warning! Before assembly DO NOT CONNECT TO POWER SUPPLY.! 1. The safety guard is comprised of two assemblies pre-assembled at the factory, the transparent guard assembly (fig 2) and the riving knife/ anti-kickback pawl assembly (fig 3). 2. It will be helpful to attach the handle (H, fig 1) to the handwheel (I, fig 1) at this point. 2
3 3. Be sure the blade tilt lock lever (K, fig 1) is tight. 4. Remove the table insert (Q, fig 1). Insert a screwdriver into the 1/2 (12 mm) round hole and lift the insert from its place in the table. English 5. Raise the saw blade to its full height. Turn the handle on the handwheel clockwise to do this. The outer surface of the handwheel changes the blade angle and the inner wheel raises and lowers the blade. 6. Insert the base of the riving knife into the clamp slot behind the blade as shown (fig 4). The lock lever (a, fig 4) on the clamp slot should be pointing up to allow the insertion. 7. When the riving knife is fully inserted and seated firmly, move the lock lever 1/4 turn counter-clockwise to clamp it there. 8. Place the transparent guard assembly on top of the riving knife so that the slot in the guard s aluminum support bar engages the two hooks (h, fig 3) along the top edge of the knife, just ahead of the attachment bracket (b, fig 3) for the anti-kickback pawls. You will have to loosen the lock knob (k, fig 2) at the back of the guard assembly aluminum support bar. 9. When the guard assembly is firmly hooked into the slot, re-tighten the lock knob. 10. Should it be necessary during a particular cutting operation to temporarily remove the anti-kickback pawls from the guard assembly, they can be removed by pulling the lock pin (p, fig 3). Warning! Be sure to re-attach the pawls when your job is done. 11. Re-install the insert plate. Mounting the rip fence 1. The fence is pre-assembled in the carton. 2. Hook the back of the fence over the rear edge of the table top. 3. Lower the front of the rip fence onto the front rail, with the fence lock handle up. This allows it to slide along the rail. Pushing down on the fence lock handle clamps the fence squarely into place. 4. Should it be necessary, the lock nut at the rear of the fence can be used to increase or decrease the tension on the locking lever. Warning! Always ensure the rip fence is parallel to the saw blade before use to avoid blade jam and kick back.!! addendum
4 English Parts List POS. PART NO. DESCRIPTION Qty. 1 TJ250GA03002 Blade guard 1 2 TJ250GA03006 Bead flange GB Cylindrical pin 8 x TJ250GA03007 Anti-kickback support 1 5 TJ250GA03008 Locking shaft 1 6 TJ250GA03005 Anti-kickback pawl 2 7 GB/T818 Pan head screw M5 x TJ250GA03003 Guard support 1 9 TJ250GA03009 Spring 1 10 TJ250GA03004 Riving knife 1 11 TJ250GA02008 Table insert 1 12 TJ250GA01001 Table Locking dog 1 14 TJ250GA01003B Slide rail 1 15 DJ250A02008A-2 Clamping block 1 16 TJ250GA04004A Fence 1 17 GB/T5783 Hexagon bolt M6 x TJ250GA04002 Pull rod 1 19 RTS250K04003 Slide carriage 1 20 GB/T879.1 Spring column pin 1 21 RTS250K04006 Lock lever 1 22 RTS250K04005 Tension knob 1 23 GB/T818 Pan head screw M6 x GB/T818 Pan head screw M4 x RTS250K04001 Indicator 1 26 GB/T879.1 Spring column pin Knob 1 28 GB/T96.2 Flat washer DJ250B Miter gauge 1 30 GB/T819.1 Flat head screw M4 x RTS250K04007 Miter gauge plate 1 32 GB/T818 Pan head screw M4 x GB/T97.1 Flat washer DJ250B Indicator 1 35 RTS250K04016B Miter gauge bar 1 36 GB/T70.1 Slotted cheese-head 2 screw M8 x GB/T93 Spring washer GB/T96.2 Flat washer TJ250B02012A Driven pulley PJ251 Poly V-belt 1 41 GB/T894.1 External circlip HC13120F-T Motor 1 43 GB/T276 Bearing Z 2 44 TJ250B03024 Spacer 1 45 GB/T893.1 External circlip GB/T6170 Hex nut M TJ250B02015A Shaft assembly 1 48 RTS250H03030 Live shaft assembly 1 49 GB/T70.1 Slotted cheese-head screw M5 x 12 4 POS. PART NO. DESCRIPTION Qty. 50 RTS250H02003 Riving knife plate 1 51 GB/T889.1 Self-locking nut M TJ250GA02005 Riving knife support 1 53 TJ250GA02007 Handle 4 54 TJ250GA02006 Riving knife pressing 1 plate 55 GB/T818 Pan head screw M3 x GB/T5783 Hexagon bolt M8 x GB/T894.1 External circlip TJ250E01011B Blade 1 59 TJ B Flange 1 60 GB/T6173 Nut M16 x GB/T80 Set screw M6 x TJ250B02013A Drive pulley 1 63 RTS250G06015A Bolt 2 64 GB/T1972 Spring washer 2 65 GB/T889.1 Self locking nut M RTS250G03034 Motor bracket 1 67 RTS250G03009 Gear 1 68 GB/T14 Square neck bolt M6 1 x RTS250G03032 Leading truck 1 70 GB/T818 Pan head screw M5 x TJ250GA02004 Tie plate 1 72 RTS250G06019 Protective plate 1 73 RTS250H03045 Lever 1 74 GB/T818 Pan head screw M5 x RTS250G06020 Rotating plate 1 76 GB/T818 Pan head screw M5 x GB/T889.1/1 Self-locking nut M GB/T1972 Spring washer 2 79 GB/T Hex nut M TJ B Screw shaft 1 81 GB/T819.1 Flat head screw M4 x GB/T97.1 Flat washer GB/T6170 Hex nut M GB/T819.1 Flat head screw M8 x GB/T70.1 Slotted cheese-head 2 screw M8 x GB/T96.2 Flat washer Handle 1 88 RTS250G06003 Hand wheel 1 89 GB/T1972 Belleville spring washer 4 90 RTS250G06004 Rocker arm 1 91 RTS250G06022 Hand wheel knob 1 92 RTS250G06025/ Tube 1 93 GB/T70.1 Slotted cheese-head 1 screw M6 x RTS250G06023 Knob cover 1 95 GB/T819.1 Flat head screw M4 x RTS250G03003 Cable support 2 POS. PART NO. DESCRIPTION Qty. 97 Cable P-4 Cable gland 3 99 RTS250G03001A Housing GB/T845 Tapping screw ST4.2 4 x RTS250K05002 Junction box TJ250GA04009 Earth plate RTS250G05001 Switch plate HY18-4P Switch GB/T846 Tapping screw ST3.5 2 x GB/T97.1 Flat washer GB/T5783 Hexagon bolt M6 x GB/T5783 Hexagon bolt M6 x RTS250G03012 Blade support RTS250G06009 Retention knob GB/T5783 Hexagon bolt M6 x TJ Back clip TJ Front clip TJ315B06012A Push stick TJ250B06020 Wrench RTS250G06013 Bottom plate GB/T845 Tapping screw ST3.5 6 x TJ250W06002 Side skirt TJ250W06004 Side stretcher RTS250M03001 Leg DT/ Foot pad TJ250W06003 Front and rear stretcher TJ250W06001 Front and rear skirt GB/T119.1 Cylindrical pin 5 x GB/T5783 Hexagon bolt M6 x GB/T6170 Hex nut M DJ250A02008A-3 Spring GB/T93 Spring washer GB/T70.1 Slotted cheese-head 4 screw M10 x GB/T93 Spring washer RTS250G06006 Angle pointer TJ250W01100 Front plate GB/T879.1/ Cylindrical pin 3 x RTS250G03025 Threaded rod RTS250G03010 Gear rack RTS250G03002 Base guard GB/T896 Split washer TJ250GA03010 Spring B/D Knob GB/T39 Square nut M GB/T96.2 Flat washer 5 2 4
5 Schematic drawing English addendum
6 English 6
Operating Instructions and Parts Manual 10-inch Table Saw
Operating Instructions and Parts Manual 10-inch Table Saw Model 66 shown with optional extension table and legs, mobile base, and motor cover WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part
EXCERPT FROM THE Jobsite saw OWNERS MANUAL
Table and Fence Table and Fence Parts List 0 0 0 0 0 0 0 0 Table JSS-00 Fence Roller Pin (mm x mm) JSS-0 Rear Lock Down Screw for Insert JSS-00 0 mm O-Ring JSS-00 Extension Wing JSS-00 Fence Roller Wheel
25-200H. 12 Planer / Jointer. with Helical Cutterhead. Parts List.
25-200H 12 Planer / Jointer with Helical Cutterhead 4001824 Parts List www.rikontools.com CABINET ASSEMBLY PARTS EXPLOSION & PARTS LIST KEY NO. DESCRIPTION KEY NO. DESCRIPTION 1 Pan Head Screw M6x12 P25-200H-1
RYOBI 10 IN (254 MM) TABLE SAW MODEL NO. BT REPAIR SHEET
RYOBI 0 IN (2 MM) TABLE SAW MODEL NO. BT00- REPAIR SHEET 2 RYOBI 0 in. (2 mm) TABLE SAW - MODEL NO. BT00- FOR MITER TABLE ASSEMBLY, REFER TO FIGURE B FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE E FOR RIP
SECTION 9: PARTS. Table Breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION
SECTION 9: PARTS Table Breakdown 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 23 25 17 26 27 8 1 P0675001 CAP SCREW M8-1.25 X 30 15 P0675015 SUPPORT BLOCK 2 P0675002 TABLE SUPPORT BLOCK
RYOBI 10 in. (254 mm) TABLE SAW MODEL NO. BT3100 REPAIR SHEET
RYOBI 0 in. (4 mm) TABLE SAW MODEL NO. BT00 REPAIR SHEET FOR MITER TABLE ASSEMBLY, REFER TO FIGURE B FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE E FOR RIP FENCE ASSEMBLY, REFER TO FIGURE C FOR MOTOR ASSEMBLY,
RYOBI. 10 in. (254 mm) TABLE SAW MODEL NO. BTS15 REPAIR SHEET
RYOBI 0 in. ( mm) TABLE SAW MODEL NO. BTS REPAIR SHEET FIGURE A 0 0 0 0 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding
Model W1837 (For Machines Mfd. Since 8/18) PARTS. Main PARTS -83-
-83- Main 29 30 31 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 113 96 90 91 92 93 95 96 97 98 100 101 102 103 104 105 106 109
RYOBI 10 in. TABLE SAW - MODEL NO. BT3000
FOR MITER TABLE ASSEMBLY, REFER TO FIGURE 0 RYOBI 0 in. TABLE SAW - MODEL NO. BT000 FIGURE 5: 0 in. TABLE SAW FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE FOR RIP FENCE ASSEMBLY, REFER TO FIGURE FOR MOTOR
SPARE PARTS LIST MODEL NO. LB1200F PAGE 1 ITEM PART NO. DESCRIPTION QTY NOTE
PAGE 1 001 JM21000018 HEX.SOCKET HEAD SCREW M5X12 4 002 JM21000019 SPRING WASHER 5 4 003 JM21000020 FLAT WASHER 5 4 004 JM21000021 UP COVER COMPLETE 1 005 JM21000025 MICRO SWITCH FIX PANEL A 1 006 JM21000026
Assembly Instructions
Assembly Instructions 10 CONTRACTOR TABLE SAW Model No. 351.218330 Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A. www.sears.com/craftsman 31624.00 Draft (10/08/09) UNPACKING The
Parts List for Type 1
1 422190430001 FENCE BODY 1 2 901010600677 CAP SCREW 2 3 904010331451 WASHER 3 4 901010600605 CAP SCREW 2 5 904010101604S STEEL WASHER 2 6 422040105002 REAR SLIDE BLOCK 1 7 905040714459 STEEL PIN 1 8 928010414118
G0513X2 Main -87- G0513 Series Bandsaws 82V V2 82-6V2 95A V2 82-5V2 82-1V2 82-4V V A
G0513X2 Main 23 55 22 48 17 17-1 17-2 21 7 17-3 17-2 17-4 24 17-5 18-5 22 24 21 55A 50 8 9 49 11 12 13 14 15 47 16 10 46 45 3 44 43 39 38 37 39 40 32 33 36 42 34 35 2 25 28 18-4 18-2 18-3 31 30 29 18-1
SECTION 10: PARTS. Main Model G0771Z (Mfd. Since 09/16)
SECTION 10: PARTS Main 96 103 105 119 104 120 102 101 124 29-1 29-4 29-2 29-5 29-3 29-6 29-7 29-8 29-9 29-10 97 98 99 121 100 106 97 98 99 100 121 96 29 27 28 125 24 25 26 30 53 41 40 39 31 34 114 115
MODEL RA-2500N RADIAL ARM SAW
1 6130089 HEX. NUT (L.H.T.) W5/8"-18UNF 2.18 2 6900549 WASHER 1.78 3 6080529 ARBOR COLLAR 31.02 4 6760117 OILLESS METAL 1.57 5 9270612 CLAMP SCREW M6 X 12 0.19 6 9220625 HEX. SOCKET HEAD BOLT M6 X 25 0.22
SECTION 10: PARTS Body
-76- Model G0690/G0691 (Mfd. 6/15+) SECTION 10: PARTS 55V2 55-1 55-2 55-3V2 55-5 55-6 8 9 9 56 10 10 68 69 70 71 55-4 1 2 3 4 5 6 7 8 9 14 15 18 19 20 21 22 23 24 25 26 27 27 28 29 30 31 32 32 33 33 34
Model W1819/W1820 (Mfg. Since 09/11) PARTS. Body V V PARTS -79-
-79- Model W1819/W1820 (Mfg. Since 09/11) 155V2 155-1 155-2 155-3V2 155-6 155-5 108 109 109 156 110 110 168 169 170 171 101 102 103 104 105 106 107 108 109 114 115 118 119 120 121 122 123 124 125 126 127
G0513X2 Main. G0513 Series Bandsaws (Mfd. Since 07/18) A V2
G0513X2 Main 55 17 48 7 16 55A 14 15 49 13 47 50 12 10 71 70 72 73 59 69 74 46 11 9 8 76 5 75 4 68 81 80 67 66 48 50 39 78 79 23 17-3 17-2 17-1 17-4 17-2 21 22 24 17-5 32 33 34 35 28 2 45 3 38 44 39 43
Main Breakdown. Model G0531B/G0566B V2 (G0531B) 80V2-2
Main Breakdown 53 85-1 54 59 54 56 54 52 55 57 175 53 56 85 29 119-2 114 89 22 119-2 119 107 119-5 119-3 119-6 119-1 29 22 119-4 114 112 96 113 114 100 116 117 105 120 102 103 108 115 99 98 92 91 90 73
Model No. MLT100 TABLE SAW 255MM
Page 1 / 6 Page 2 / 6 Page 3 / 6 Page 4 / 6 Page 5 / 6 Page 6 / 6 Page 1 / 8 001 JM27000001 HEX.BOLT M10X35 4 002 JM27000002 SPRING WASHER 10 4 003 JM27000003 FLAT WASHER 10 4 004 JM27000004 CROSS HEAD
Repair Parts. Parts List for RIDGID 10 Inch Table Saw Model No. TS Figure 1. RIDGID parts are available on-line at
Parts List for RIDGID 0 Inch Table Saw Model TS00 Figure 0 0 0 0 See Figure 0 See Figure 0 See Figure Parts List for RIDGID 0 Inch Table Saw Model TS00 Figure Always Order by Part Number - not by Number
Main SECTION 10: PARTS
Main SECTION 10: PARTS Main Parts List 3 P0732003 MITER GAUGE ASSEMBLY 37 P0732037 TRANSFER PULLEY 3-1 P0732003-1 MITER GAUGE HANDLE 38 PR05M EXT RETAINING RING 15MM 3-2 PW01M FLAT WASHER 8MM 39 P6002-2RS
INSTRUCTION MANUAL AND PARTS LIST MODEL 14-10
VERTICAL BAND SAWS INSTRUCTION MANUAL AND PARTS LIST MODEL 1-10 DAKE/PARMA WHEN ORDERING PARTS GIVE COMPLETE SERIAL NUMBER OF MACHINE GIVE PART NUMBER AND NAME GIVE AMOUNT REQUIRED Unless the above data
SECTION 10: PARTS. Body
SECTION 10: PARTS Body 1 P0715P001 EXTENSION WING 17 PS14M PHLP HD SCR M6-1 X 12 2 PCAP88M CAP SCREW M10-1.25 X 25 18 PLW03M LOCK WASHER 6MM 3 PLW06M LOCK WASHER 10MM 19 PWF06M FENDER WASHER 6MM 4 PW04M
RYOBI 10 in. TABLE SAW MODEL NO. BTS16 REPAIR SHEET
RYOBI 0 in. TABLE SAW MODEL NO. BTS REPAIR SHEET FIGURE A FIGURE E FIGURE H FIGURE C FIGURE D 0 0 FIGURE B 0 0 NOTE A WARNING: Improper electrical repair of the table saw can result in damage to the drive
SECTION 9: PARTS G0513/G0513P/G0513ANV
SECTION 9: PARTS G0513/G0513P/G0513ANV Main 21 22 23 82-6 82-5 48 22 19 20 24 18 17 24 17 26 21 55 17 16 14 15 32 33 34 20 18 27 25 50 13 47 18 82-1 175 35 55A 49 9 11-1 10 46 45 11 12 44 176 39 38 37
2705 03-09 99 98 97 82 88 89 83 84 85 86 87 101 103 100 106 81 71 105 104 73 74 75 76 77 78 80 79 57 62 58 56 63 65 66 67 68 64 69 70 59 60 61 31 30 29 32 34 35 41 40 42 36 37 38 39 43 4445 46 33 55 54
SawStop. Contractor Fence Assembly OWNER S MANUAL. Model CNS-SFA
Contractor Fence Assembly OWNER S MANUAL Model CNS-SFA Warranty warrants to the original retail purchaser of the Contractor Fence Assembly accompanying this manual that the fence assembly will be free
Model LS1018 Parts List A = Standard Equipment 〇 = Circuit Diagram
LS1018 7-14 103 104 105 106 97 99 100 110 109 63 85 96 200 107 90 2 199 108 37 89 91 92 93 94 31 74 75 73 140 70 121 15 254 255 113 215 236 116 114 115 196 258 195 118 197 119 259 117 203 253 67 95 112
Main Parts. -6- Model G0555LA35 (Mfd. Since 10/17) 30A V
60 49 50 76 41 65 66 44 46 43 42 47 51 63 58 64 59 48 62 16 61V2 50 51 55 56 57 70 49 69 64 55 56 43 57 167 154 41 40 8 22 30A 44 45 3 4 Main Parts 14 15 16 7 168 155 30 195 34 194 186 6 68 24 115 116
Electric Skein Winder
Electric Skein Winder Assembly and Use Package Contents 1 - Triangular Body (w/ motor) 1 - Cross Arm 1 - Left Foot (w/ yarn guide) 1 - Right Foot 1 - Adjustable Finger (w/ yarn clip) 3 - Adjustable Fingers
F l a t S c r e e n A R M S I n s t a l l a t i o n
ITEM NUMBERS (1) #TOACAORG16 (2) #TOACAORG20 (3) #TOACATRP24 (4) #TOACATRP30 (5) #TOACATRPDS (6) #TOACATRPSS TOOLS REQUIRED (1) 3/8 Wrench (not provided) (2) Phillips head screwdriver (not provided) (1)
SECTION 10: PARTS G1023RL
SECTION 10: PARTS 131 132 133 G1023RL (All) Main 121 118 119 128 126 125 124 123 124 122 120 119 128 116 6V2 5 4V2 4-1 129 127 128 117 26V3 26-3V2 26-1 6-2 (G1023RLWX) 26-2 26-4V3 7 6-1 1 (G1023RL) 19-1
Parts List: VBS-3612 Band Saw
Parts List: VBS-3612 Band Saw (refer to breakdowns on pages 35 and 36) Index No. Part No. Description Size Qty 1... VBS3612-101...Gear Box... 1 2... TS-0209101...Socket Head Cap Screw...3/8-16 x 2-1/4...
model tsa-sa48 Sliding Crosscut Table installation guide
model tsa-sa48 Sliding Crosscut Table installation guide A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop
TECHNICAL INFORMATION
TECHNICAL INFORMATION P 1 / 11 Model No. Description CONCEPT AND MAIN APPLICATIONS Specification Standard equipment TCT saw blade... 1 Rear table set (exclusively Europe, Turkey, South Africa..1 2704 This
SERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" SLIDING COMPOUND MITER SAW
PAGE 1 OF 6 BASE ASSEMBLY 00 0 CATALOG NO. EXAMPLE: SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS 6955-20 1 02-80-0050 Thrust Bearing (1) 2 05-80-0510 M5 x 12mm Flat Head T-20 Screw (5) 3 05-81-0135
Interactive Monitor Arm
Interactive Monitor Arm Tools Required -5mm Allen wrench -Phillips screwdriver -Plastic mallet There are two ways to attach a Monitor Arm to a Full Frame; with a Beam, or with a Post Mount. Both methods
LISTA DE REFACCION MODELO LS1017L PAGINA 1. Pos. NUMERO DESCRIPCION Cant. NOTA
PAGINA 1 001 JM23100006 CROSS HEAD SCREW M5X20 2 002 JM23100007 FLAT WASHER 5 2 003 JM23100008 PAD 4 004 JM23100009 LOCKNUT M10 1 005 JM23100010 FLAT WASHER 10 2 006 JM23100300 BASE COMPLETE 1 INC. 7 007
JET Heavy-Duty B3NCH 10" Jobsite Table Saw
JET Heavy-Duty B3NCH 10" Jobsite Table Saw The JET Heavy-Duty 10" Jobsite Table Saw brings many of the capabilities of a full-sized table saw to the jobsite, small or temporary woodworking shops. The unique
SERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" DUAL BEVEL COMPOUND MITER SAW B27B
PAGE 1 OF 6 BASE ASSEMBLY 00 0 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS = Part number change from previous service
Model LS0815F Parts List A = Standard Equipment 〇 = Circuit Diagram
LS0815F 4-14 1 3 4 6 32 7 47 48 42 44 41 43 11 10 16 14 15 8 9 24 20 19 22 17 21 18 13 23 27 26 29 33 31 35 34 36 86 87 89 90 93 105 104 107 108 109 110 111 101 100 63 83 84 69 67 65 72 79 80 81 85 77
Model PLM5113N PETROL LAWN MOWER
Strana 1 / 2 Strana 2 / 2 Strana 1 / 4 001 671006065 "BLADE TIGHTEN BOLT 3/8""24" 1 002 671010730 LID SHAPE WASHER 1 003 DA00000973 BLADE 510MM 1 004 671015252 BLADE SUPPORT 1 005 DA00000535 FLAT KEY 1
ABM International, Inc. Navigator Assembly Manual
ABM International, Inc. 1 1.0: Parts List Tablet (Qty. 1) Tablet mount (Qty. 1) NOTE: Mount may appear and operate different then image below Control Box (Qty. 1) Motor Power Supply (Qty. 1) 2 X-axis motor
LISTA DE REFACCION MODELO LS1018L PAGINA 1. Pos. NUMERO DESCRIPCION Cant. NOTA
PAGINA 1 001 JM23100006 CROSS HEAD SCREW M5X20 2 002 JM23100007 FLAT WASHER 5 2 003 JM23100008 PAD 4 004 JM23100009 LOCKNUT M10 1 005 JM23100010 FLAT WASHER 10 2 006 JM23100300 BASE COMPLETE 1 INC. 7 007
MODEL NO.: MI PARTS BREAKDOWN
MODEL NO.: MI-76350 PARTS BREAKDOWN MAGNUM DRILL PRESS ASSEMBLY INSTRUCTIONS MODEL MI-76350 Before you begin to assemble your drill press, review the parts breakdown and keep it ready for reference. Start
M2 Assembly. M2 Sub-Assemblies mm Belt Sub-Assembly mm Belt Sub-Assembly Spider Sub-Assembly... 4
M2 Assembly Table of Contents M2 Sub-Assemblies... 3 630mm Belt Sub-Assembly... 3 702mm Belt Sub-Assembly... 3 Spider Sub-Assembly... 4 Idler Bolt Sub-Assembly... 8 Y Motor Sub-Assembly... 9 X Motor Sub-Assembly...
OWNER S MANUAL CONTENTS. The only table saw fence with Automatic Positioning Control TM
The only table saw fence with Automatic Positioning Control TM OWNER S MANUAL Please read this owner s manual before use and keep it at hand for reference. Note: The INCRA TS II system consists of three
Symptom Possible Cause Correction. Motor will not start Low voltage. Check power line for proper voltage. Open circuit in motor or loose connection.
Saw blade Blade guard Troubleshooting Symptom Possible Cause Correction Motor will not start Low voltage. Check power line for proper voltage. Open circuit in motor or loose connection. Inspect all lead
PLATINUM SERIES TABLESAW W/DOVETAIL MECH LEFT-TILT MANUAL
PLATINUM SERIES TABLESAW W/DOVETAIL MECH LEFT-TILT MANUAL LAGUNA TOOLS 2072 Alton Parkway Irvine, California 92606 Ph: 800.234.1976 www.lagunatools.com 2018, Laguna Tools, Inc. LAGUNA and the LAGUNA Logo
ABM International, Inc.
ABM International, Inc. Lightning Stitch required 1 1.0: Parts List head and motor assembly (Qty. 1) Reel stand (Qty. 1) Needle bar frame clamp (Qty. 1) Motor drive (Qty. 1) 2 Cable harness with bracket
MODEL RA-200N RADIAL ARM SAW
ITEM NO PART NO DESCRIPTION PRICE 1 6130089 HEX. NUT (L.H.T.) W5/8"-18UNF 2.18 2 6900079 CONICAL SPRING 16.3 X 31.5 X 1.2 0.78 3 6940444 OUTER FLANGE 4.49 4 6940443 INNER FLANGE 4.91 5 6100509 PARALLEL
Horizontal and Vertical. Metal Cutting Band Saw MODEL: BS-115
Horizontal and Vertical Metal Cutting Band Saw MODEL: BS-5 SAFETY. Know your band saw. Read the operator s Manual carefully. Learn the operations, applications and limitation.. Use recommended accessories.
Coolant Tank Screen Leg Idle End Lockwasher 64 B-015B Leg Drive End Machine Screw 1/4-20 x 3/4 Round Head
Always give model number, serial number and part number when ordering repair parts. BED, COOLANT & DASH POT PARTS LIST (Cont'd.) REF NO. PART NUMBER DESCRIPTION 19 B-077 Vise Slide Block 20 B-045 Vise
Note: Parts without part numbers are for reference only and cannot be purchased individually.
Parts Ordering Replacement Parts To order parts or reach our service department, call 1-800-274-6848 between 7:30am and 5:30pm (CST), Monday through Friday. Having the Model Number and Serial Number of
AndyMark DART 12.
AndyMark DART 12 Part Number Description QTY These Parts Are Pre-Assembled by AndyMark am-0031 Bearing, 3/16"ID (R3) 1 am-0209 Bearing, 3/8"ID 1614ZZ 2 am-1028 Screw, #10-32x3/8 Pan Head Philips 8 am-1121
How to program the digital speed display (This is factory set and will only need to be programmed if the unit is replaced)
How to program the digital speed display (This is factory set and will only need to be programmed if the unit is replaced) 1. Press and hold the set button (top left corner) until the display shows Fun
SECTION 9: PARTS Main
SECTION 9: PARTS Main 58 63 67 66 65 67 66 59 58 49 58 48 49 61A 61 64 62 55 50 35-3 34 35-1 57 56 41 42 151 51 50 33A 35-2 30A 30A-1 35 38 39 31 32 18 40 43 44 68 51 41 45 46 57 56 55 47 152 153 20 21
G5959Z 12" Left-Tilting Table Saw -37-
Date Serial Number GROUND. 329 401 403 411 ALWAYS USE GUARDS AND ANTI-KICKBACK DEVICES 401 107 106 152 406 404 405 408 138 412 410 409 402 151 101A 139 144 143 140 142 141 114 101B 137 108 102 103 128A
Note: Parts without part numbers are for reference only and cannot be purchased individually.
Parts Ordering Replacement Parts To order parts or reach our service department, call 1-800-274-6848 Monday through Friday (see our website for business hours, www.waltermeier.com). Having the Model Number
J-3-D PART NO DATE:
37-380 & 37-877 8 PROFESSIONAL JOINTER J-3-D PART NO. 909563 DATE: 05-12-04 Page1/ J-3-D /DEB REPLACEMENT PARTS * 1345487 CUTTERHEAD ASSY, INCL: 1 1340196 KNIFE SCREW 2 1345488 BAR 3 37-355 KNIVES (SET
535A. Main Components. Pipe and Bolt Threading Machine. Printed in U.S.A. Ridge Tool Company/Elyria, Ohio, U.S.A.
Pipe and Bolt Threading Machine A Main Components 0 Screw, Button Head /" - 0 x /" () Washer, Flat /" ()" Top Cover 0 Base Bottom Cover Screw, Pan Head # - x " () Carriage Assembly 0 Front Support Bar
SECTION 9: PARTS Main
63 58 62 61A 66 65 67 66 67 58 58 59 64 SECTION 9: PARTS 162 161 Main 160 45 152 21 20 17 153 166 33 30A 31 32 135 144 133 136 34 35-2 35-3 131 16 130 134 139 15 35-1 137 14V2 151 140 38 143 150 18 142
WOLF PUP LOOM TM & WOLF PUP LT LOOM TM
WOLF PUP LOOM TM & WOLF PUP LT LOOM TM Assembly Instructions FL3000 FL3006 FL3009 WOLF PUP WOLF PUP LT Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212
TP1300 OWNERS MANUAL 13 INCH THICKNESS PLANER WITH LEGSET. For Your Safety: Read all instructions carefully Save this manual for future referenece
TP00 OWNERS MANUAL INCH THICKNESS PLANER WITH LEGSET For Your Safety: Read all instructions carefully Save this manual for future referenece SP Printed in Taiwan Parts List for " Thickness Planer Model
Assembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set
Assembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-708482 Ph.: 800-274-6848 Revision C2 02/2013
Note: Parts without part numbers are for reference only and cannot be purchased individually.
Parts Ordering Replacement Parts To order parts or reach our service department, call 1-800-274-6848 Monday through Friday (see our website for business hours, www.waltermeier.com). Having the Model Number
BASE, COLUMN, ARM AND TABLE
SPARE S LIST Item No. 700000 Article No. 84-2265 IMPORTANT INSTRUCTIONS It is most important that the above illustration be studied prior to the assembly of the saw blade and arbor or the assembly of the
CATALOG OF REPLACEMENT PARTS
The Choice of Experience CATALOG OF REPLACEMENT PARTS MODELS 909A 919A 909E 919E 909M 919M SLICERS EFFECTIVE MARCH 2009 - 2 - Table of Contents 5 ELECTRICAL COMPONENTS (909A & 919A) 7 ELECTRICAL COMPONENTS
Pickup Box Utility Rack Package Installation (Instruction ID: )
017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation
Tin Lizzie 18 Assembly Instructions
Tin Lizzie 18 Assembly Instructions Revision: 07/29/16 Table of Contents Aides 3 Before You Begin 5 Aides 5 Tools 6 Perfect Stitch Parts 2 12 Modify the Machine 12 Prepare Drill Templates 12 Front Display
Assembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set #
Assembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set #1002493 JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-708482 Ph.: 800-274-6848 Revision C3 02/2014 www.jettools.com
Parts Catalog. S-Series Slicer Manual Frozen Option S13. Model:
, 07 995 ECN 08 Parts Catalog S S-Series Slicer Manual Frozen Option Model: S 05/0/07 Rev. G IMPORTANT! TO EXPEDITE SHIPMENT OF PARTS, ALWAYS SPECIFY MODEL, REV, PART NUMBER, AND SERIAL NUMBER OF UNIT.
Disc, Belt, and Combination Disc/Belt Sanders
This Manual is Bookmarked Operating Instructions Parts Manual Disc, Belt, and Combination Disc/Belt Sanders Models: 4200A, 4300A, 4400A 4200A Disc/Belt Sander 4300A 6 Inch Belt Sander 4400A 12 Inch Disc
Parts List Index No. Part No. Description Size Qty
Parts List Index No. Part No. Description Size Qty 1... TS-1541031...Lock Nut...M8... 4 2... JJP12-002...Washer... 4 3... JJP12-003...Outfeed Table Bracket Shaft... 1 4... JJP12-004...Outfeed Table Bracket,
OWNER S MANUAL CONTENTS. The only table saw fence with Automatic Positioning Control TM
The only table saw fence with Automatic Positioning Control TM OWNER S MANUAL Please read this owner s manual before use and keep it at hand for reference. Note: The INCRA TS III system consists of three
Replacing the Reciprocator on an SWF Multi-head.
Replacing the Reciprocator on an SWF Multi-head. Follow the instructions below to replace the reciprocator in the SWF multi-head machines. The tools required are found in the tool kit that came with the
Main Parts. -4- Model G0555LANV (Mfg. Since 1/13) 30A V
60 49 50 76 41 65 66 44 46 43 42 47 51 63 58 64 59 50 51 55 56 57 70 49 69 64 48 62 16 61 55 56 43 57 167 154 41 40 8 22 30A 44 45 3 4 Main Parts 14 15 16 7 168 155 30 195 34V2 194 186 6 68 24 115 116
Dear Woodworker: Thank you for your purchase and welcome to the Laguna Tools group of discriminating woodworkers. I understand that you have a choice
Platinum Series Tablesaw w/ Dovetail Mech Left-tilt Manual 17101 Murphy Avenue, Irvine, CA 92614 www.lagunatools.com 800.234.1976 MTS0300-0180 1 Table saw Dear Woodworker: Thank you for your purchase and
VARIABLE SPEED WOOD LATHE. Model DB900 INSTRUCTION MANUAL
VARIABLE SPEED WOOD LATHE Model DB900 INSTRUCTION MANUAL 1007 TABLE OF CONTENTS SECTION...PAGE Technical data.. 1 General safety rules....1-3 Specific safety rules for wood lathe.....3 Electrical information.4
Customer Notice: Congratulations again on your SawStop purchase, and thank you! -SawStop Tualatin, OR
Customer Notice: Congratulations on the purchase of this Sliding Crosscut Attachment. As the owner of a SawStop saw, you are familiar with our high standards for quality, fit and finish. Different from
Parts Catalog. S-Series Slicer Smart Manual SG13. Model:
, 07 99507 ECN 065 Parts Catalog S-Series Slicer Smart Manual Model: SG SG 0/0/07 Rev. G IMPORTANT! TO EXPEDITE SHIPMENT OF PARTS, ALWAYS SPECIFY MODEL, REV, PART NUMBER, AND SERIAL NUMBER OF UNIT. GLOBE
SECTION 9: PARTS. Table. Spiral Cutterhead For Model G0452Z Cutterhead For Models G0452/P Model G0452/P/Z (Mfg.
SECTION 9: PARTS Table 17 18 19 87 86 21 262-3 262-1 262-2 27 28 29 30 22 23 24 35 36 37 38 262 25 26 2 13 Cutterhead For Models G0452/P 10 45 12 13 7 8 9 50A 6 11 31 14 15 16 12 13 81 82 83 84 32 85 33
Gared Pro-S Portable Backstop
Models: 9616 & 9618 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE PUBLICATION
Replacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C)
Follow the instructions below to replace the reciprocator in the SWF Compact series machines. The tools required can be found in the tool kit that came with the machine. Preparation 1. First, place the
PARTS Stand Breakdown
PARTS Stand Breakdown 35-5 35-2 35-4 63 1 2 3 4 5 35-1 35-3 36 37 38 39 35 34 33 32 30 28 6 7 8 21 29 23 22 27 26 25 24 42 43 44 45 46 47 9 10 62 61 60 51 11 59 19 18 12 12 13 58 14 57 15 56 55 54 53 52
N. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Dump Body tarping system. With tarping systems
LU6X-130 Instructions and Parts List (including LU6X Basic) Operating Instructions
LORTONE LU6X-130 Item # 061-092 LU6X Basic Item # 061-090 LU6X-130 Instructions and Parts List (including LU6X Basic) Operating Instructions Introduction The LU6X is one the most versatile pieces of equipment
Makita Werkzeug Ges.m.b.H. Airportstr. 4, 2401 Fischamend Tel: / Fax: / Mail: Web:
Airportstr., 0 Fischamend Tel: 0 / 777 00 Fax: 0 / 777 00-0 Makita Service Information / Model: LB00F Seite / (c) 09 by Makita Austria. All Rights Reserved. Änderungen und Irrtümer vorbehalten / MSIO V.0
Sliding Crosscut Table installation guide
Sliding Crosscut Table installation guide model tsa-sa48 A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop
Parts Breakdown Page 1 of 13 2/13
Page 1 of 13 2/13 Page 2 of 13 2/13 Page 3 of 13 2/13 Page 4 of 13 2/13 Page 5 of 13 2/13 Page 6 of 13 2/13 Page 7 of 13 2/13 Products with multiple versions are listed in subsiding order with the newest
Side Winder R o u t e r L i f t.
Woodpeckers PRECISION WOODWORKING TOOLS Side Winder R o u t e r L i f t. INSTALLATION INSTRUCTIONS The wrench handle must be pointing left in order to fully insert or remove it. Lift Wrench Once fully
Xceed ASSEMBLY MANUAL
Xceed ASSEMBLY MANUAL Table of Contents / Registration Congratulations on your commitment to fitness and your purchase of the Bowflex Xceed home gym. Before assembling your Bowflex Xceed home gym please
Model No: TC10. Parts Information: Tyre Changer - Automatic
Page 1 of 11 1 TC10.01 BODY 2 TC10.02 COLUMN 3 TC10.03 HORIZONTAL ARM ASS'Y 4 TC10.04 WASHER 5 TC10.05 RUBBER FOOT 6 TC10.06 COVER 7 TC10.07 SCREW M14x42 8 TC10.08 PRESS COVER 9 TC10.09 STOP-UP 10 TC10.10
FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Trailer system.
CONTENTS PRECAUTIONS BEFORE STARTING OPERATION PREPARATION FOR OPERATION CAUTIONS ON USE OPERATION
CONTENTS PRECAUTIONS BEFORE STARTING OPERATION ------------------------------------- 1 PREPARATION FOR OPERATION 1. Adjustment of needle bar stop position ---------------------------------------------------------
MODEL G0501 SLIDING TABLE SAW
MODEL G0501 SLIDING TABLE SAW MANUAL UPDATE The Sliding Table Saw has changed slightly from when the manual was originally written. We have improved the crosscut fence, extension tables, blade guard assembly,
SECTION 11: PARTS Main
SECTION 11: PARTS Main 55 48 21 20 22 7 18 19 23 17 17 18 21 22 14 15 16 32 33 34 26 27 50 49 13 47 35 2 18 20 55A 12 11 8 10 45 46 3 38 37 44 53 36 51 42 25 30 29 28 43 99 103 98 100 52 101 5 4 58 57
Operating Instructions and Parts Manual. 10 x 16 Horizontal Band Saw Models J-7020, J-7040
Operating Instructions and Parts Manual 10 x 16 Horizontal Band Saw Models J-7020, J-7040 JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-414472 Ph.: 800-274-6848 Revision C2 03/2014 www.jettools.com
MODEL H " BYRD SHELIX CUTTERHEAD INSTRUCTIONS
MODEL H9291 12" BYRD SHELIX CUTTERHEAD INSTRUCTIONS The Model H9291 12" Byrd Shelix cutterhead is designed to replace the straight-knife cutterhead on the Grizzly jointer Model G0609. The total procedure