PLATINUM SERIES TABLESAW W/DOVETAIL MECH LEFT-TILT MANUAL

Size: px

Start display at page:

Download "PLATINUM SERIES TABLESAW W/DOVETAIL MECH LEFT-TILT MANUAL"

Ernest McDowell
5 years ago
Views:

PLATINUM SERIES TABLESAW W/DOVETAIL MECH LEFT-TILT MANUAL LAGUNA TOOLS 2072 Alton Parkway Irvine, California 92606 Ph: 800.234.1976 www.

1 PLATINUM SERIES TABLESAW W/DOVETAIL MECH LEFT-TILT MANUAL LAGUNA TOOLS 2072 Alton Parkway Irvine, California Ph: , Laguna Tools, Inc. LAGUNA and the LAGUNA Logo are the registered trademarks of Laguna Tools, Inc. All rights reserved.

3 Table of contents Content Page number Safety Rules 4 Warranty 5 Noise emission 6 Specification sheet 6 Receiving your machine 7 Introduction to your machine 8 Parts of the table 8 Where to locate your machine 10 Unpacking your machine 11 Assembly and setup, Adjusting 15 Before start machine 26 Machine test 27 Maintenance and troubleshooting 28 Exploded view drawings 32 MTS Table saw

4 Safety Rules As with all machinery there are certain hazards involved with the operation and use. Using it with caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result. If you have any questions relative to the installation and operation, do not use the equipment until you have contacted your supplying distributor. Read carefully before operating the machine: 1. Keep the working area clean and be sure adequate lighting is available. 2. Do not wear loose clothing, gloves, bracelets, necklaces or ornaments. Wear face, eye, respiratory and body protection devices as indicated for the operation or environment. 3. Be sure that the power is disconnected from the machine before tools are serviced or an attachment is to be fitted or removed. 4. Never leave the machine with the power on. 5. Do not use dull, gummy or cracked cutting tools. 6. Be sure that the keys and adjusting wrenches have been removed and all the nuts and bolts are secured. MTS Table saw

5 Limited Warranty New machines and accessories sold by Laguna Tools carry a one-year warranty effective from the date of shipping. Machines sold through dealers must be registered with Laguna Tools within 30 days of purchase to be covered by this warranty. Laguna Tools guarantees all new machines and accessories sold to be free of manufacturers defective workmanship, parts and materials. We will repair or replace, without charge, any parts determined by Laguna Tools, Inc. to be a manufacturer s defect. We require that the defective item/part be returned to Laguna Tools with the complaint. Any machines returned to Laguna Tools must be returned with packaging in the same manner in which it was received. If a part or blade is being returned it must have adequate packaging to ensure no damage is received during shipping. In the event the item/part is determined to be damaged due to lack of maintenance, cleaning or misuse/abuse, the customer will be responsible for the cost to replace the item/part, plus all related shipping charges. This limited warranty does not apply to natural disasters, acts of terrorism, normal wear and tear, product failure due to lack of maintenance or cleaning, damage caused by accident, neglect, lack of or inadequate dust collection, misuse/abuse or damage caused where repair or alterations have been made or attempted by others. Laguna Tools, Inc. is not responsible for additional tools or modifications sold or performed (other than from/by Laguna Tools, Inc.) on any Laguna Tools, Inc. machine. Warranty maybe voided upon the addition of such described tools and/or modifications, determined on a case-by-case basis. Software purchased through Laguna Tools Inc. is not covered under this warranty and all technical support must be managed through the software provider. Software is non-refundable. Normal user alignment, adjustment, tuning and machine settings are not covered by this warranty. It is the responsibility of the user to understand basic machinery operation, settings and procedures and to properly maintain the equipment in accordance with the standards provided by the manufacturer. Parts, under warranty, are shipped at Laguna Tools, Inc. s cost either by common carrier, FEDEX ground service or a similar method. Technical support to install replacement parts is primarily provided by phone, fax, or Laguna Tools Customer Support Website. The labor required to install replacement parts is the responsibility of the user. Laguna Tools is not responsible for damage or loss caused by a freight company or other circumstances not in our control. All claims for loss or damaged goods must be notified to Laguna Tools within twenty-four hours of delivery. Please contact our Customer Service Department for more information. Only new machines sold to the original owner are covered by this warranty. For warranty repair information, call

6 Noise Emission Specification Sheet 4HP Single Phase 462Lbs

8 Introduction to Table Saws Parts of the Table saw MTS Table saw

9 Identification. Cabinet Table Extension Table. Trunion Electrical System MTS Table saw

10 Rip Fence. Dust Collection. Throat Plate. Miter Gauge. Where to Locate your Machine MTS Table saw

11 Unpacking your Machine. 1 WARNING: EXTREME CAUTION MUST BE USED BECAUSE THE BANDING WILL SPRING AND COULD CAUSE INJURY Note Note MTS Table saw

12 Note: MTS Table saw

13 What you will receive with the machine. Dado throat plate Tool kit Handle Handle lock screw Miter gauge Cast iron extension tables Extension table Fence Extension table parts MTS Table saw

14 Extension table parts Dust extractor panel Cover Extension table rails Manual Guard MTS Table saw

15 Assembly and set up Cleaning the machine. Assembling the side cast iron extensions tables Note MTS Table saw

16 4. Remove the motor transport bracket. Fitting the motor cover MTS Table saw

17 Fit the dust extraction plate Fitting the angular movement handle Note:- Note:- Key MTS Table saw

18 Fitting the extension table. Fitting the fence rails MTS Table saw

19 5 6 Knob Clamp plate Fitting and adjusting the fence Spacer Vertical adjusting screws MTS Table saw

20 3. Straight edge Note:- Adjusting screws 6. Adjusting screws MTS Table saw

21 Fitting the electrical box. MTS Table saw

22 MTS Table saw

23 MTS Table saw

24 Note:- Connecting the electrical supply. Note A qualified electrician must carry out the installation. MTS Table saw

25 Miter Gauge Tilt Mechanism Stops MTS Table saw

26 Note:- The machine may not be supplied with an electrical plug, as the type of plug will be dependent on the installation. Before starting the machine MTS Table saw

27 16. Machine test Before you cut any wood read the safety rules at the front of this manual MTS Table saw

28 Maintenance and Troubleshooting Weekly Maintanince Drive Belt Table Insert Bearings Rust MTS Table saw

29 Tilt Mechanism is Tight Vertical Mechanism is Tight Troubleshooting Poor Cut Saw will not Start MTS Table saw

30 The Machine will not Stop Motor Tries to Start but will not Turn Motor Overheats Squeaking Noise Blade Slows Down During a Cut MTS Table saw

31 Blade Overheats Machine Vibrates 1 2 Poor Dust Collection Causes of the Blade Dulling MTS Table saw

32 PARTS LIST Table Saw Body Breakdown REF# DESCRIPTION QTY REF# DESCRIPTION QTY 101 CABINET FLAT WASHER CAP SCREW STD TABLE INSERT ELASTIC WASHER SET SCREW FLAT WASHER PAN HEAD SCREW ANGLE SCALE DADO TABLE INSERT INSULATOR SCREW CABINET PLATE SCUTCHEON PAN HEAD SCREW RIVETS FOR NAME OF FLAT WASHER SHIPING STRIP BELT PLATE HEX HEAD BOLT PAN HEAD SCREW FLAT WASHER FLAT WASHER ELASTIC WASHER MOTOR COVER NUT CAP SCREW DUST CLIP CLEANOUT DOOR PAN HEAD SCREW DOOR LATCH FLAT WASHER KNOB ELASTIC WASHER FLAT WASHER HOOK ELASTIC WASHER ELASTIC WASHER NUT FLAT WASHER DUST HOOD PAN HEAD SCREW PAN HEAD SCREW NUT TABLE SET SCREW M5X EXTENSION WING PLATE CAP SCREW DADO TABLE INSERT ELASTIC WASHER 6 MTS Table saw

33 Trunnion Assembly Breakdown MTS Table saw

34 REF# DESCRIPTION QTY REF# DESCRIPTION QTY 201 ANGLE POINTER BRACKET SET SCREW M8X COPPER WASHER PIN LOCK SHAFT CAP SCREW M8x PINION LOCK WASHER 8MM SET SCREW M6X WORM GEAR LOCK SPACER NUT M COPPER HOOP HEX BOLT M8X LOCK NUT M12X FLAT WASHER BEARING CAP SCREW M5x KEY C5X BEARING SHAFT FOR WORM SCREW BOLT SUPPORT BLOCK LOCK NUT M16X HEX BOLT M6X SWIVEL BOX LOCK WASHER6MM KEY FLAT WASHER 6MM PULLEY WORM COLLAR FLAT WASHER 8MM BEARING HEX BOLT M8X NUT CAP SCREW M8X RAISING BLOCK 1 (274) MOTOR PLATE CAP SCREW M6X BRACKET HOOP SPLITTER ADJUST BLOCK WAVE WASHER KNURLED KNOB BLADE ARBOR SPRING ARBOR FLANGE PIN NUT SPLITTER TIGHTEN CLIP COLLAR SPACER GEAR BELT LOCK WASHER 5MM FRONT TRUNNION SPLIT PIN 4X REAR TRUNNION ORIENTATION PIN LEFT BRACKET HEX BOLT M12X RIGHT BRACKET FLAT WASHER 12MM PLATE LOCK WASHER 12MM HEX BOLT M X NUT M ADJUST BOLT MOTOR CAP SCREW M X SET SCREW CAP SCREW M X PULLEY CAP SCREW M X KEY FLAT WASHER 10MM BAR LOCK WASHER 10MM BLOCK HEX NUT M10X SET SCREW M8X15 4 MTS Table saw

35 Blade Guard Breakdown REF# DERIPTION QTY REF# DERIPTION QTY 315 ROLL PIN PHLP HD SCR M TORSION SPRING HEX BOLT M LOCK NUT M GUARD SUPPORT SUPPORTING ARM PHLP HD SCR M PHLP HD SCR M SPACER FLAT WASHER 6MM SPACER TOP GUARD PHLP HD SCR M PHLP HD SCR M FLAT WASHER 5MM FRONT GUARD PAWL SIDE GUARD SPLITTER V SPRING REED RIVING KNIFE LOCK NUT M M PHLP HD SCR M RIVING KNIFE HOOK PLATE 1SET 337 ROLL PIN MTS Table saw

36 Miter Gauge Breakdown REF# DESCRIPTION QTY REF# DESCRIPTION QTY 410 MITER STOP PIN BLOCK MITER BAR COMPRESSION SPRING GIB MITER STOP PIN SET SCREW M4-.7* CAP SCREW M4-.7* CAP SCREW M4-.7* POINTER MITER GUAGE MITER RING FLAT WASHER 4MM FLAT HD SCR M5-.8* LOCK WASHER 4MM MITER BODY PIVOT PIN PHLP HD SCR M4-.7* MITER GUAGE BODY MITER KNOB MITER STOP PIN KNOB FENDER WASHER 10MM 1 MTS Table saw

37 Fence Breakdown REF# DESCRIPTION QTY REF# DESCRIPTION QTY 502 FANCE FACE HEX BOLT M6-1* CAP SCREW M6-1* LOCK NUT M GLIDE PAD HEX BOLT M10-1.5* FENCE SCALE WINDOW LOCK NUT M SET SCREW M * CAM FOOT PHLP HD SCR M5-.8* MAGNET LOCK WASHER 5MM CAM INDICATOR FENCE LOCK KNOB FENCE BODY SET SCREW M * SET SCREW SPECIAL LOCKING NUT M MTS Table saw

38 30 Rail & Extension Table Breakdown REF# DESCRIPTION QTY REF# DESCRIPTION QTY 601 INSERT FENCE LOCK WASHER 8MM GUIDE TUBE FLAT WASHER 8MM SCALE REAR RAIL FRONT RAIL HEX BOLT M8-1.25* CAP SCREW M6-1* HEX NUT M LOCK WASHER 6MM TABLE BOARD FLAT WASHER 6MM HEX BOLT M8-1.25* HEX BOLT 5/16-18*1-1/2 2 MTS Table saw

39 50 Rail & Extension Table Breakdown REF# DESCRIPTION QTY REF# DESCRIPTION QTY 601 INSERT FENCE LEG CAP SCREW M6-1* FOOT LOCK WASHER 6MM HEX BOLT M FLAT WASHER 6MM CAP SCREW M6-1* HEX BOLT 5/16-18*1-1/ CAP SCREW M8-1.25* LOCK WASHER 8MM HEX BOLT M8-1.25* FLAT WASHER 8MM GUIDE TUBE HEX BOLT M8-1.25* SCALE HEX NUT M FRONT RAIL TABLE BOARD REAR RAIL 1 MTS Table saw

40 2072 Alton Parkway. Irvine, CA Ph: Laguna Tools is not responsible for errors or omissions. Specifications subject to change. Machines may be shown with optional accessories. 2018, Laguna Tools, Inc. LAGUNA and the LAGUNA Logo are the registered trademarks of Laguna Tools, Inc. All rights reserved.

Dear Woodworker: Thank you for your purchase and welcome to the Laguna Tools group of discriminating woodworkers. I understand that you have a choice

Platinum Series Tablesaw w/ Dovetail Mech Left-tilt Manual 17101 Murphy Avenue, Irvine, CA 92614 www.lagunatools.com 800.234.1976 MTS0300-0180 1 Table saw Dear Woodworker: Thank you for your purchase and