OWNERS MANUAL MODEL F660 HIP SLED
|
|
- Lizbeth Melinda Green
- 6 years ago
- Views:
Transcription
1 OWNERS MANUAL MODEL F HIP SLED QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will guarantee your complete satisfaction through our authorized dealer service centers or our home office customer service department. Please call your local dealer for assistance or BodyCraft at (:00 AM - 5:00 PM). Our trained technicians will provide immediate assistance to you, free of charge. Bodycraft is a division of Recreation Supply Inc. 7 Green Meadows Drive Lewis Center, OH 0 0B
2 BEFORE YOU BEGIN Congratulations and thank you for selecting the F HIP SLED strength training system. The F HIP SLED offers an impressive array of strength training exercises to develop every major muscle group of the body. Whether your goal is cardiovascular fitness, a shapely, toned body or dramatic muscle size and strength, the F HIP SLED will help you achieve the specific results you want. For your safety and benefit, read this manual and the accompanying literature before using the F HIP SLED. Keep this manual for future reference. If you have additional questions, please call your local dealer or our customer service department at Monday through Friday, a.m. until 5 p.m. Eastern Time. IMPORTANT SAFETY NOTES There is a risk assumed by individuals who use this type of equipment. Before beginning this or any other exercise program consult your physician. This is especially important for individuals over the age of or persons with pre-existing health problems. Recreation Supply, Inc. assumes no responsibility for personal injury or property damage sustained by or through use of this product.. This product must be assembled on a flat, level surface to assure its proper function.. Clean pads and frame on a regular basis. We recommend warm, soapy water. Do not use harsh or abrasive chemicals.. Inspect and tighten all parts before every use. Replace any worn parts immediately. Failure to do so may result in serious injury.. Keep children away from the F HIP SLED at all times. 5. Keep your hands away from cables and pulleys during operation. Keep your hands away from moving parts other than the designated handles.. When adjusting the seat, make sure the spring pin is fully engaged. If not, the seat may slip and cause serious injury. 7. Exercise with care to avoid injury. 8. If unsure about the proper use of the F HIP SLED strength training system call your local dealer or our customer service department at
3 OVERVIEW
4 NO. DESCRIPTION MAIN FRAME FRONT STABILIZER REAR UPRIGHT LINEAR BEARING ASSEMBLY SOLID GUIDE ROD BASE CONNECTOR RIGHT SHOULDER ASSEMBLY LEFT SHOULDER ASSEMBLY LEG PRESS PLATE FOOT PLATFORM HIP PAD PLATE WEIGHT HOLDER CALF BLOCK WEIGHT HOLDER SUPPORT RIGHT SAFETY STOPPER LEFT SAFETY STOPPER FOOT PLATFORM ADJUSTER SLEEVE FOOT PLATFORM ADJUSTER INSIDE TUBE METAL HINGE FOOT PLATFORM AXLE FOOT PLATE AXLE PLASTIC CAP HAND GRIP 8mm LOCKING PIN SPRING CLIP SEAT PAD BACK AND HIP PAD BACK SUPPORTER PAD BACK PAD RIGHT SHOULDER PAD LEFT SHOULDER PAD X 75mm END CAP 5 X 5mm SQ CAP 75 X mm END PLUG 8mm ROUND PLUG mm ROUND PLUG 5mm ROUND PLUG X mm PLASTIC SLEEVE /" X 8mm BUSHING LINEAR BEARING RUBBER BUMPER PLASTIC STUD SPRING KNOB POP PIN /" X -/" HEX BOLT /" X -/" HEX BOLT /" X " HEX BOLT 5/" X -/" HEX BOLT /8" X -/" HEX BOLT (ALL) /8" X " INNER HEX SCREW /8" X /" INNER HEX SCREW ALLEN BOLT M8 X 0mm DOME BOLT 5/" X /" SET SCREW /" WASHER /8" WASHER (LARGER) /8" WASHER (SMALLER) SPRING CLIP /" NYLON NUT /8" NYLON NUT 5/" SPRING WASHER mm HEX KEY mm HEX KEY FOAM TUBE mm ROUND PLUG NON SLIP X mm SQ CAP 75 X mm END CAP PARTS LIST QTY / / / / / / / / / / / / (inch) " " " " / / / 5" / / / "
5 STEP Base Frame Assembly To ease the assembly process, do NOT tighten bolts until instructed. Assembly requires two people.. Attach the Base Connector () to the Bolts welded on the Front Stabilizer () using two /" Washers () and two /" Nylon Nuts ().. Attach the Base Connector () to the Bolts welded on the Rear Upright () using two /" Washers () and two /" Nylon Nuts (). Slide the two X 75 mm End Caps () onto the Front Stabilizer () and the Rear Upright ().. Attach the pre-assembled Main Frame () to the vertical bolts welded on the Front Stabilizer () using two /" Washers () and two /" Nylon Nuts (). Attach the Rear Upright () to the bolts welded to the top of the Main Frame () using two /" Washers () and /" Nylon Nuts (). Slide the two 75 X mm End Caps () onto the Main Frame ().. Slide the X mm Sq Cap (7) onto the Linear Bearing Assembly (). 7
6 STEP Shoulder Pads, Safety Stoppers, and Weight Holder Assembly. Attach the Weight Holder Support () to the Weight Holder () using one /" X -/" Hex Bolt ( ), two /" Washers (), and one /" Nylon Nut () on the top hole of the Weight Holder () and one /" X " Hex Bolt (7) at the bottom threaded hole.. Attach the Weight Holder Assembly ( & ) to the bolts welded to the underside of the Linear Bearing Assembly () and tighten with four /" Washers () and four /" Nylon Nuts ().. Insert the top end of the Right Safety Stopper (5) into the top bracket on the Main Frame () and then slide the bottom end into the low bracket on Main Frame (). Check to make sure the Safety Stopper rotates and slides freely. Insert an 8mm Locking Pin () into the hole on the top of the Right Safety Stopper (5). Tap the Locking Pin with a hammer to makes sure it is permanently attached. Repeat the procedure for the Left Safety Stopper ().. Attach two 8mm Round Plugs () to the top on both Shoulder Assemblies (7, 8). Attach one mm Round Plug () to the handles at the top on both Shoulder Assemblies (7, 8). 5. Pull the Spring Knob () on the right side of the Linear Bearing Assembly () and insert the Right Shoulder Assembly (7). Attach the Right Shoulder Pad (0) to Right Shoulder Assembly (7) using two 5/" X -/" Hex Bolts (8) and two 5/" Spring Washers (). Repeat the same procedure for the Left Shoulder Assembly (8)
7 STEP Leg Press Plate and Foot Platform Assembly. Attach the bottom side of the Foot Platform (0) to the Main Frame () by aligning the holes and then inserting the solid Foot Platform Axle (0). Attach a /8" Nut () to each side of the Foot Platform Axle (0).. Find the Foot Platform Adjuster Sleeve (7). Pull the Spring Knob () and insert the Foot Platform Adjuster Inside Tube (8). Attach the Foot Platform Adjuster Sleeve (7) to the Front Stabilizer (), using one /" X -/" Bolt (5), two /" Washers () and one /" Nylon Nut ().. Attach the Foot Platform Adjuster Inside Tube (8) to the Foot Platform (0) using one /" X - /" Bolt (5), two /" Washers (), and one /" Nylon Nut ().. Attach a Back Pad (7) to the Leg Press Plate () using two /8" X " Hex Screws (). Attach the Leg Press Plate () to the Linear Bearing Assembly () by aligning the holes and then inserting the solid Foot Plate Axle (). Secure with a /8" Nut () on both sides. Pull the Pop Pin () on the Linear Bearing Assembly () to adjust the Leg Press Plate () to your desired angle
8 STEP Back Pad Assembly. Adjust the Leg Press Plate () to the flat position and then attach the Back Pad () to the Linear Bearing Assembly () using two /8" X -/" Hex Bolts () and two /8" Washers ().. Attach two Back Pads (7) to Hip Pad Plate () using four /8" X " Hex Screws () and two /8" Washers ().. Slide the two Metal Hinges () onto the small axles welded to the top of the Foot Platform (0) and then attach the Back Pad (8) to the Metal Hinges () using two /8" X " Hex Screws () and two /8" Washers ().. The Spring Clips (5) are used to hold the weight plates on the Weight Holder ()
9 STEP 5 Calf Raise Assembly. Attach the Non Slip () to the Calf Block (). Attach one mm End Plug () and two 75 X mm End Caps (8) to the Calf Block (). To perform calf raises, insert the Calf Block into the central hole in the Foot Platform (0).. Attach Back Pad Assembly (7) to the Leg Press Plate ()
10 Assembly is complete! Please take the following steps before using the gym:. Make certain all bolts are tightened securely.. For better performance, apply a household lubricant (such as silicone) to any adjustable areas and to the Linear Bearing Assembly().. Enjoy many years of a Fit Lifestyle. Thank you for purchasing the F HIP SLED. If You have any questions, please call your local BodyCraft dealer or call our customer service department at
INSTRUCTION MANUAL LEG PRESS OPTION OF ELITE GYM
INSTRUCTION MANUAL LEG PRESS OPTION OF ELITE GYM QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will
More informationPOWER RACK STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL MODEL : F430 POWER RACK
POWER RACK STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL MODEL : F0 POWER RACK QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing
More informationPFT CABLE GYM INSTRUCTION MANUAL
PFT CABLE GYM INSTRUCTION MANUAL QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will guarantee your
More informationSMITH STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL MODEL : F410
SMITH STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL MODEL : F0 QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts,
More informationCFT STRENGTH TRAINING SYSTEM OWNER'S MANUAL
CFT STRENGTH TRAINING SYSTEM OWNER'S MANUAL Serial Number Location SERIAL 8 Record your Serial number and purchase date here: S/N PURCH.DATE: DEALER: Scan this QR code with your PortableDevice to link
More informationSerial Number Location
GL/GLX STRENGTH TRAINING SYSTEM OWNERS MANUAL Serial Number Location SERIAL 3 4 5 7 8 Record your Serial number and purchase date here: S/N DATE: DEALER: Model No. BCG-GL BODYCRAFT is a division of Recreation
More informationSTRATA STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL
STRATA STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will
More informationAX1001. Smith/Functional training Combo-free weight ASSEMBLY INSTRUCTIONS
AX1001 Smith/Functional training Combo-free weight ASSEMBLY INSTRUCTIONS EXPLODED DIAGRAM 83 84 84 85/86 87 87 88 89 90 91 62 64 64 64 64 64 64 65 65 65 65 66 66 65 66 66 65 63 63 66 67 68 55 66 66 70
More informationLifeGear G1 /HOME GYM ITEM NO.: 63100
LifeGear G1 /HOME GYM ITEM NO.: 63100 OWNER S MANUAL IMPORTANT: Read all instructions carefully before using this product. Retain this owner s manual for future reference. The specifications of this product
More informationCOMPETITOR CB-610 STANDARD BENCH
NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice COMPETITOR CB-610 STANDARD BENCH Hardware Identifier Assembly Instruction Exploded Diagram Parts List
More informationSTRATA STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL
STRATA STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will
More informationOlympic Bench Model 6600
Olympic Bench Model 6600 IMPORTANT SAFETY INSTRUCTIONS TKO Fitness products are designed and manufactured to the highest standards in order to provide you with years of great workouts. We proudly stand
More informationThe Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 )
P/N: 001-7057 Rev ( /0 ) The Bowflex Revolution XP Home Gym Assembly Instructions 2 Table of Contents Before You Start... 2 Tools You Will Need / Hardware Contents... 3 Box Contents... 6 Assembling Your
More informationHOME GYM Owner s Manual
HOME GYM Owner s Manual Content Content-------------------------------------------------------------1 Safety precautions----------------------------------------------------2 Assembly instruction-------------------------------------------------3-12
More informationA SSEMBLY INSTRUCTION MAN UAL
A SSEMBLY INSTRUCTION MAN UAL TABLE OF CONTENTS: Introduction- Pg. 1 Assembly for TG-150- Fig. 1-71 Cable Mapping Diagram- Pg. 20 Cable Adjustments- Fig. 42, 65, Pg. 19 Exploded View Diagram- Pg. 22 Parts
More informationCOMPETITOR WM-203 COMBO BENCH
NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier COMPETITOR WM-203 COMBO BENCH Assembly Instruction Exploded Diagram Parts List
More informationPHG-1000X. Owner s Manual HOME GYM
HOME GYM Owner s Manual WWW.BODYSOLID.COM THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES:! " # $ % & ' ( ) * + ' (, ' " -. *, * ) )
More informationMARCY CLASSIC MCB-252 COMBO BENCH W/120 lbs Weight Set
NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction MARCY CLASSIC MCB-252 COMBO BENCH W/120 lbs Weight Set Exploded
More informationM2 Assembly. M2 Sub-Assemblies mm Belt Sub-Assembly mm Belt Sub-Assembly Spider Sub-Assembly... 4
M2 Assembly Table of Contents M2 Sub-Assemblies... 3 630mm Belt Sub-Assembly... 3 702mm Belt Sub-Assembly... 3 Spider Sub-Assembly... 4 Idler Bolt Sub-Assembly... 8 Y Motor Sub-Assembly... 9 X Motor Sub-Assembly...
More informationXceed ASSEMBLY MANUAL
Xceed ASSEMBLY MANUAL Table of Contents / Registration Congratulations on your commitment to fitness and your purchase of the Bowflex Xceed home gym. Before assembling your Bowflex Xceed home gym please
More informationStar Trac Turbo Trainer Assembly & Setup
Star Trac Turbo Trainer Use the following procedures to unpack and assemble your Turbo Trainer manufactured by Star Trac. UNPACKING AND PARTS LIST Position the shipping carton so the Heavy End logo is
More informationSole Fitness E95 Elliptical Trainer TurnKey Delivery and Setup Training
Sole Fitness E95 Elliptical Trainer TurnKey Delivery and Setup Training Delivery Requirements Ground delivery Inside delivery to customer-specified location Unpack and assemble machine, and remove packing
More informationPSC-43X. Owner s Manual SEATED CALF RAISE
SEATED CALF RAISE Owner s Manual WWW.BODYSOLID.COM THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES: Inspect equipment before each workout.
More informationAssembly. Item G7 Qty 1. Item D4. M10 x 55 mm Allen Bolt. Item D5. Qty 2. Item E13 Qty 4 M10 Flat Washer. Item B18. M8 x 30 mm Allen Bolt (Black)
ACCESSORY FITMENT LIST These are all the accessories you will need to complete the assembly of your product. The following accessories are supplied in a pack and should be checked before attempting assembly
More informationF-GHR OWNER S MANUAL. Glute Ham Raise. CAUTION! Read all precautions and instructions in this manual before using this equipment.
OWNER S MANUAL F-GHR Glute Ham Raise CAUTION! Read all precautions and instructions in this manual before using this equipment. 1 ASSEMBLY MANUAL FORCE USA GLUTE HAM RAISE F-GHR BEFORE YOU START Remove
More informationODY-5. Odyssey Home Gym TABLE OF CONTENTS: Introduction - Pg. 1. Safety Precautions - Pg. 2. Assembly for ODY-5 - Pg. 3 - Pg. 18, Pg.
TABLE OF CONTENTS: Introduction - Pg. 1 Safety Precautions - Pg. 2 O W N E R S M A N U A L Assembly for ODY-5 - Pg. 3 - Pg. 18, Pg.20 Cable Adjustments - Pg. 19 Cable Mapping Diagram - Pg. 21 - Pg. 24
More informationTITAN2-EDGE Public Access Computer Station Dual Track
TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the
More informationOWNER S MANUAL. Dual Adjustable Pulley Machine. Model #: N820 DP
OWNER S MANUAL Dual Adjustable Pulley Machine! Model #: N820 DP Caution: Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. Contents
More informationPOWER TOWER OWNER S. Item #1720
POWER TOWER OWNER S Item #1720 TABLE OF CONTENTS SERVICE ------------------------------------------------------------------------- 2 IMPORTANT LABELS --------------------------------------------------------
More informationPlease read and understand the OnBoard Timpani Cart Owner s Manual before using the Timpani Cart.
Assembly and Owner s Manual OnBoard Timpani Cart Performance Position Towing Position CONTENTS Important User Information...........................2 General......................................2 Manufacturer.................................2
More informationDeluxe Inversion Table SF-1201
Deluxe Inversion Table SF-1201 Take a few moments to familiarize yourself with the specific parts and hardware included with your product. Make sure all the parts and hardware are included in the carton
More informationINSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058
INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationFord Pick Up Rear leaf Spring Kit Installation Instructions
1948-1956 Ford Pick Up Rear leaf Spring Kit Installation Instructions 1-800-984-6259 www.totalcostinvolved.com Parts 48 inch leaf (2) springs (4) U-bolts 3/8-24 x l 1/4bolts (16) & nuts (2) 1/2-20 x 4
More informationHardware and Components:
Hardware and Components: (A) 4X 5/16 x 1 Carriage Bolt (B) 2X 5/16 x 2-1/4 Carriage Bolt (C) 2X 5/16 x 3-1/4 Hex Bolt (D) 2X 5/16 x 3/4 Hex Bolt (E) 2X 5/16 x 1-1/4 Hex Bolt (F) 5/16 x 2-1/4 Hex Bolt (G)
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2
INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationOwner s Manual XM-7617 POWER TOWER
Owner s Manual XM-767 POWER TOWER Table of Contents Important Safety Information Before You Start Assembly Parts List Exploded View 3 5-0 Important Safety Information NOTE: Hand tighten bolts and nylon
More informationPVLP-156X. Owner s Manual VERTICAL LEG PRESS
VERTICAL LEG PRESS Owner s Manual WWW.BODYSOLID.COM THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES: Inspect equipment before each workout.
More informationBODY-SOLID,Inc S. Des Plaines Ave. Forest Park, IL USA Phone:(708) Fax:(708)
BODY-SOLID,Inc. 1900 S. Des Plaines Ave. Forest Park, IL 60130 USA Phone:(708)427-3555 Fax:(708)427-3556 www.bodysolid.com EXM-1500GOWNER'S MANUAL TABLE OF CONTENTS General Instructions.......2 Training
More informationThis manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified.
This manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified. Step #1 Lay all parts out to verify quantities. (2) 2 x 25-1/4
More informationThank you for purchasing our product! *Please read these instructions and follow them step by step.*
07/07/08.rev1 PAGE 1 OF 11 601AL VERTICAL 60120VL LIFT W/CHAIN DRIVE WINCH Thank you for purchasing our product! *Please read these instructions and follow them step by step.* Step 1. Separate and group
More informationGIOT (fits onto G2B, G3S, G4I, G5S, G6B, G9S, G10B) ASSEMBLY INSTRUCTIONS
GIOT (fits onto GB, G3S, GI, G5S, G6B, G9S, G0B) ASSEMBLY INSTRUCTIONS Before You Begin Thank you for purchasing the Inner And Outer Thigh Attachment. This is part of the Body-Solid line of quality strength
More informationStrata. urniture. Adriana Instructions. Parts in the Arm Box: Parts in the Body Box: Watch our assembly videos at
1A Watch our assembly videos at www.strataf.com/videos Parts in the Arm Box: Arm - Outside View Arm - Inside View 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 with the Feet attached Back Panel
More informationHardware and Components:
Hardware and Components: (A) 5/16 x 2 Hex Bolt (B) 5/16 x 2-1/4 Hex Bolt (C) 5/16 x 2-1/2 Hex Bolt (D) 4X 5/16 x 3/4 Hex Bolt (E) 4X 5/16 x 1-1/4 Hex Bolt (F) 11X 5/16 Flat Washer (G) 12X 5/16 Nylock Nut
More informationMAG-CONV Basic, 48, 48R & Midline Front Mount
Parts Required: Tools Used: Mag Wheels Brakes Brake Rods Mounting Bracket Anti Tippers 7/16" Wrench Screw Driver Rubber Mallet 5/8 Wrench 5mm Allen Wrench Step Execution Figures 1 Remove front 5" total
More informationThe Bowflex Blaze Home Gym Assembly Manual
The Bowflex Blaze Home Gym Manual P 001-6903 Rev A (4/2006) Safety Precautions 1 Get to Know Your Machine 2 Basic Principles 3 Parts List 3 Hardware List 3 Accessory List 3 Hardware Guide 4 Tools You Will
More informationPLA144X. Owner s Manual LAT ROW STATION
LAT ROW STATION Owner s Manual WWW.BODYSOLID.COM THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES: Inspect equipment before each workout.
More informationJenny Legs Assembly Instructions
Jenny Legs Assembly Instructions R EXTENDED PHILLIPS BIT MM ALLEN WRENCH 6MM HEX DRIVE /" 007 Steelcase Inc. Grand Rapids, MI 90 U.S.A. Printed in U.S.A. Page of 6 88000 Rev F Jenny Club Instructions:
More informationPOWERHOUSE BENCH PHC -265
NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction POWERHOUSE BENCH PHC -265 Parts List Warranty Ordering Parts
More informationWARNING. BX Ford F350 (Includes Super Duty) Installation Instructions
Serial Number BX231 Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More information3 in 1 (Lawn mower/aerator/raker)
3 in (Lawn mower/aerator/raker) CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. Safety Assembly Operation Maintenance Parts TABLE OF CONTENTS
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART #
INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Brackets (for trucks without 22 12mm x 30.1mm OD
More informationP a r k c o n s o l e s i n k a s s e m b l y i n s t r u c t i o n s
P a r k c o n s o l e s i n k a s s e m b l y i n s t r u c t i o n s Before You Begin: Professional installation by two-person crew is required for this fixture. Install water supply and drain piping
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
2005-08 Pontiac G6 GT Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationGared Pro-S Portable Backstop
Models: 9616 & 9618 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE PUBLICATION
More information`48-`56 Ford Pickup Rear leaf Spring Kit Installation Instructions Tech Line:
`48-`56 Ford Pickup Rear leaf Spring Kit Installation Instructions Tech Line: 1-855-693-1259 www.totalcostinvolved.com CHECK ALL PARTS INCLUDED IN THIS KIT TO THE PARTS LIST BEFORE INSTALLING THE KIT.
More informationStrata. urniture. Mission Rim Instructions. Parts in the Arm Box: Parts in the Body Box:
1A Watch our assembly videos at www.strataf.com/videos.html Parts in the Arm Box: Arm - Outside View Arm - Inside View Corbels x 4 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 with the Feet attached
More informationWARNING Honda CR-V Honda Element Installation Instructions BX2232. Serial Number
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationWARNING. BX Ford Explorer With Adaptive Cruise Control & Eco Boost Installation Instructions
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationBRM * This item is for consumer use only and it is not meant for commercial use.
BRM 10 * This item is for consumer use only and it is not meant for commercial use. OWNER S MANUAL General Information Safety Before you undertake any exercise program, please be sure to consult with your
More informationExploded Diagram /1/23
& Exploded Diagram www.firstdegreefitness.com 2018/1/23 Upper Frame Assembly A048 Seat Assembly A078 60806 60809 10097 A039 Lower Frame Assembly 10041 1 Nyloc Nut M10 10082 3 Washer M10x21x2 10097 1 Nut
More informationModel 20: Home & Garden Cart
Model 20: Home & Garden Cart Parts List Step 1: A: Install two ¾ Bolts (C) through the rear trim piece on the Bottom Panel (S) and attach to Lock Nuts. (Lock nuts on bottom side) B: Place left Side Panel
More information-- Gym Glide -- (Recreational Game Standard) Installation Instructions
-- Gym Glide -- (Recreational Game Standard) Installation Instructions Call Jaypro Sports Equipment at 1-800-243-0533 during regular business hours for technical support. www.jaypro.com Rev- Page 1 of
More information55000/55010 Installation Instructions
A. Install 55015 B. Bolt roof rails, 55020/55025, to front hoop. C. Assemble 55026 D. To install without drilling into bumper. E. If mounting directly to bumper. A. 55015 Installation Instructions 55000/55010
More information400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
More informationStrata. urniture. Addison Instructions. Parts in the Arm Box: Parts in the Body Box: Watch our assembly videos at
1A Watch our assembly videos at www.strataf.com/videos.html Parts in the Arm Box: Arm - Outside View Arm - Inside View Corbels x 4 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 Back Panel x 1 with
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
Serial Number 2012 Hyundai Accent (No Foglights) Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories
More informationOPERATOR'S MANUAL 46" SNOW BLADE. Model Numbers OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
OPERATOR'S MANUAL 46" SNOW BLADE Model Numbers 190-833-OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A. FORM NO.
More informationThe Brute Plate Loaded Home Gym TABLE OF CONTENTS: Introduction - Pg. 1. Safety Precautions - Pg. 2. Assembly for BRT-1 - Pg. 3 - Pg.
O W N E R S M A N U A L TABLE OF CONTENTS: Introduction - Pg. 1 Safety Precautions - Pg. 2 Assembly for BRT-1 - Pg. 3 - Pg. 17 Cable Adjustments - Pg. 18 Cable Mapping Diagrams Pg. 19 - Pg. 20 Parts List
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
Serial Number Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationPVKC-83X. Owner s Manual VERTICAL KNEE RAISE
VERTICAL KNEE RAISE Owner s Manual WWW.BODYSOLID.COM THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES: Inspect equipment before each
More informationThank you for purchasing out product! *Please read these instructions and follow them step by step. *
Page 1 of 7 AD17 AA DS 4 X 16 T12 Thank you for purchasing out product! *Please read these instructions and follow them step by step. * STEP 1. Slide two support posts (REF. # 24) into the two outside
More information27693 Trend Podium Desk
1 27693 Trend Podium Desk Assembly Instructions #27693 Trend Podium Desk Hardware List Part Drawing Description Qty P-1 Table Top 1 EA Part Drawing Description Qty A Screw M6 X 15mm 13 EA B Screw M6 X
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
Serial Number BX3231 2005-08 Pontiac G6 GT Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 16-1/2 Serial Number Attachment Tab Width: 24 Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and
More information100LB WEIGHT BENCH SET SF-BH6510 USER MANUAL
100LB WEIGHT BENCH SET SF-BH6510 USER MANUAL IMPORTANT: Please read this manual carefully before using the product. Retain owner s manual for future reference. For Customer Service, please contact: support@sunnyhealthfitness.com
More informationINSTALLATION INSTRUCTIONS MODEL: PLATINUM 2 BIKE FREESTAND STORAGE RACK
2420 N. Woodlawn Bldg 500 Wichita, Kansas 67220 Telephone: 800-346-7332 Web: www.mygearup.com INSTALLATION INSTRUCTIONS MODEL: 33062 PLATINUM 2 BIKE FREESTAND STORAGE RACK THANK YOU FOR YOUR PURCHASE.
More informationLEG CURL IP-S1315 INSTALLATION INSTRUCTIONS
LEG CURL IP-S35 INSTALLATION INSTRUCTIONS Copyright 2009. Star Trac by Unisen, Inc. All rights reserved, including those to reproduce this book or parts thereof in any form without first obtaining written
More informationCRYSTEEL S. this manual must be included with the vehicle after completing the installation.
Website: www.tbei.com E-mail: sales@tbei.com CRYSTEEL S Grain Tipper mounting and operating instructions this manual must be included with the vehicle after completing the installation. Web Site E-Mail
More informationPassage 4 Bike Hitch Rack
Thank you for purchasing the XPORT Passage 4 Bike Hitch rack. This rack will securely carry up to 4 bicycles. The trigger and lift assist mechanisms allow the rack to tilt up or down allowing easy access
More informationHip Roof Canopy Instructions
Hip Roof Canopy Instructions - PUT SAFETY FIRST. NOT COMPLYING WITH THE PROCEDURES AND PRECAUTIONS OUTLINED IN THIS MANUAL MAY RESULT IN PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.. Before attempting
More informationA s s e m b l y I n s t r u c t i o n s
by Body-Solid A s s e m b l y I n s t r u c t i o n s Be careful to assemble all components in the sequence they are presented. NOTE: Finger tighten all hardware in this step. Do Not wrench tighten until
More informationINSTALLATION INSTRUCTIONS 1PC FRONT BUMPER JEEP JK WRANGLER
INSTALLATION INSTRUCTIONS PARTS LIST: 1 1PC Bumper 2 8mm x 25mm Hex Bolts 1 Bull Nose Hoop 2 8mm x 16mm Hex Bolts 1 Fairlead Mounting Bracket 6 8mm x 24mm x 2mm Flat Washers 8 12mm x 35mm Hex Bolts 4 8mm
More information4099T Parts List. Front Bow Assy. (1) Rear Bow Assy. (1) Long Mounting Rail (2) Short Mounting Rail (2)
4099T Parts List Ver.2 Front Bow Assy. (1) Rear Bow Assy. (1) Small Mnt Foot (2) Large Mount Foot (2) Ladder Hook (2) Ladder Stop (2) Handle Extension (1) Long Mounting Rail (2) Short Mounting Rail (2)
More informationCam Handle Service Guide
Cam Handle Service Guide Page 2. Introduction Page 3. Troubleshooting guide Page 4-5. Adjusting the clamp force Page 6-7. Disassembling, greasing and replacing components Page 8-9. Replacing the post bearings
More informationXHD Bull Bar w/ Dual Row LED Light Bar (10-17 Jeep JK)
XHD Bull Bar w/ Dual Row LED Light Bar (10-17 Jeep JK) PARTS LIST: 1 Driver/Left Side Bull Bar Upright 8 10-1.5mm Hex Nuts 1 Side Bull Bar Upright 4 10-1.5mm Nylon Lock Nuts 1 Top Cross Bar 2 Light Bar
More informationEPPA2-KIT DUAL MONITOR ARM CONVERSION
EPPA2-KIT DUAL MONITOR ARM CONVERSION EPPA2-KIT Rev A 10/17 Model EPPA2-KIT-XXX ASSEMBLY AND ADJUSTMENT EPPA2-KIT PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
Serial Number BX2187 Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationGRILLE GUARD SPRINTER VAN (EXCLUDES X4) INCLUDES MERCEDES, FREIGHTLINER AND DODGE PARTS LIST:
PARTS LIST: 1 Grille Guard 8 12mm Hex Nuts 1 Driver/Left Side Frame Mounting Bracket 2 10-1.50mm x 25mm Button Head Bolts 1 Passenger/Right Side Frame Mounting Bracket 4 10mm x 20mm OD x 2mm Flat Washers
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 24-3/4 Attachment Tab Width: 21 Serial Number Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and
More informationWARNING BX1514. Serial Number Buick LaCrosse Installation Instructions
Serial Number Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationASSEMBLY AND ADJUSTMENT
EPPA MONITOR ARM EPPA Rev A 10/17 Model EPPA-XXX ASSEMBLY AND ADJUSTMENT EPPA MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment procedures. Check
More information3.2.3 Rear Door Window and Quarter Window Carrier Assembly
Tighten all bolts. Tighten bolts marked -1- and -2- in specified sequence. Tightening torque: 8 Nm Remaining bolts can be tightened in any sequence. Insert door window -3- through window recess without
More informationTable of Contents. Product Safety Part Drawing & Contents Hardware & Tools Assembly Adjustment
Owner s Manual A Table of Contents Product Safety.. 01. Part Drawing & Contents..... 02. Hardware & Tools.. 03. Assembly... 04. Adjustment... 10. Trouble Shooting & Maintenance.. 11. Computer... A. Warm
More informationv1.0 ASSEMBLY GUIDE Mia Wide Bookcase
v1.0 ASSEMBLY GUIDE Mia Wide Bookcase Components Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase.
More informationPSM-144X SMITH MACHINE. Owner s Manual
SMITH MACHINE Owner s Manual WWW.BODYSOLID.COM THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES: Inspect equipment before each workout.
More informationCFF GLUTE HAM RAISE/DEVELOPER
CFF GLUTE HAM RAISE/DEVELOPER GHD/GHR Assembly & Care Instructions THANK YOU! Thank you for purchasing the CFF Glute Ham Raise/Developer (CFF GHD). Please review these instructions to ensure your GHD is
More informationBX Honda Accord Ex-L 2012 Honda Accord SE Installation Instructions
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to be installed by Blue
More informationOBE165AF Elliptical Cross Trainer
OBE165AF Elliptical Cross Trainer TABLE OF CONTENTS PRODUCT SAFETY.. 01. PART DRAWING & CONTENTS..... 02. HARDWARE & TOOLS.. 04. ASSEMBLY.. 05. FOLDING.. 11. ADJUSTMENT.. 12. TROUBLE SHOOTING & MAINTENANCE
More informationMODEL 83 Pail Handler
MORSE MFG. CO., INC. 727 West Manlius Street P.O. Box 518 East Syracuse, NY 13057-0518 Phone: 315-437-8475 Fax: 315-437-1029 Email: service@morsemfgco.com Website: www.morsemfgco.com COPYRIGHT 2005 MORSE
More information200A FLB VERTICAL 22113V LIFT W/CHAIN DRIVE WINCH
PG. 1 OF 11 PORTA-DOCK, INC. 200A FLB VERTICAL 22113V LIFT W/CHAIN DRIVE WINCH STEP 1. Separate and group like parts and fasteners together. Locate the winch side member with the longer upright tube and
More information