HUNTER GREEN ADIRONDACK CHAIR

Size: px

Start display at page:

Download "HUNTER GREEN ADIRONDACK CHAIR"

Merry Thornton
5 years ago
Views:

HUNTER GREEN ADIRONDACK CHAIR 92460 ASSEMBLY &

, Camarillo, CA 930 Visit our Web Site at www.

com Copyright 2004 by Harbor Freight Tools.

No portion of this manual or any artwork contained

1 HUNTER GREEN ADIRONDACK CHAIR ASSEMBLY & OPERATING INSTRUCTIONS 349 Mission Oaks Blvd., Camarillo, CA 930 Visit our Web Site at Copyright 2004 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts please call

2 THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the owner s record below: Model Serial No. Purchase Date SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the entire manual to become familiar with the unit BEFORE you begin assembly. Technical Specifications Material: Natural Fir Wood Finish: Hunter Green paint. Height From Ground: Front, 7-/8 H, Rear, 8-7/8 H Seat Area: 9 deep x 22 wide rest: 32-/4 H x 7-3/8 W Arm Rest: 3 L x 5-/4 W Maximum Weight Capacity: 250 Lbs. Weight: 8.7 Lbs. Safety Warnings and Precautions WARNING: When assembling and using product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Read all instructions before assembly and using this product!. Keep work area clean. Cluttered areas invite injury. 2. Observe work area conditions. Keep work area well lit. 3. Check for damaged parts. Before using any product, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for any broken or damaged parts and any other conditions that may affect its operation. Replace or repair damaged or worn parts immediately. 4. Always check hardware and assembled parts after assembling. All connections should be tight and hardware tightened. 5. Keep children away. Children must never be allowed in the work area. Do not allow childrento stand on, or climb on the chair. Children should be supervised by a responsible adult when they use this product. 6. Dress properly. Gloves and nonskid footwear are recommended when assembling the Adirondack Chair. Wear restrictive hair covering to contain long hair. 7. Use eye protection. Always wear ANSI approved impact safety goggles when assembling the Adirondack Chair. 8. There are certain applications for which this Chair was designed. Do not modify this Chair and do not use this Chair for a purpose for which it was not intended. SKU For technical questions please call Page 2

3 9. Do not assemble or set up the Adirondack Chair if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not assemble or set up the Chair. 0. Only use the Chair on a flat, level and solid surface capable of supporting the Chair and the person sitting in the chair.. Do not exceed the Chair s maximum weight capacity of 250 Lbs. WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking the Adirondack Chair, check to make sure the following parts are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at Assembly/ Operation Your Adirondack Chair will require complete assembly. It is important that you read the entire manual to become familiar with the product BEFORE you assemble and use the Chair. Before assembling the Chair be sure that you have all parts described in the Parts List and Assembly Diagram located on the last pages of this manual.. Attach the Front Left Leg (C) and (C2) to the Seat (B). Line up the three (3) holes on each Front Leg (C and C2) with the 3 holes located on the right and left side of the Seat (B). Insert a Bolt (H) through each hole and thread on Nut (H) to secure-see Figure. 2. Attach one Support (D) to each side of the Seat (B) at opposite ends from the Front Legs (C and C2). The Supports (D) will be placed so that they stick up from the Seat (B) -see Figure 2. Figure Figure 2-Rear View Front Left Leg Seat Bolts and Nuts Support (D) Seat (B) 3 Bolts and Nuts (H) 3. Line up the three holes in each Support (D) with the three holes located on each side of the Seat (B). Insert a Bolt (H) through each hole and thread on Nut (H) to secure-see Figure Attach the Left Arm (E) to the Front Left Leg (C). Attach the Right Arm (E2) to the Front Right Leg (C2). Insert two Screws (G) through the Left Arm (E) and Front Left Leg (C). Repeat for Right Arm (E2) and (C2)-see Figure 3 and Figure 4 on page 4. SKU For technical questions please call Page 3

Figure 3 Figure 4 E2 Right Arm Support (D) Left Arm Front Left Leg Screws (G) Screws Right Arm(E2) C2 5. Connect the Support (D) to both the Left Arm (E) and Right Arm (E2).

Set the (A) so that the horizontal brace at the top-rear is resting on the top edge of the Supports (D). The bottom of the will rest on the Seat (B).

Attach the front Cross Brace (F) to the and Front Left Leg (C and C2). Insert Screws (G) through the front and into the front of the Legs (C and C2)-see Figure 6. 7.

Only use the Chair on a flat, level and solid surface capable of supporting the Chair and the person sitting in the chair.

4 Figure 3 Figure 4 E2 Right Arm Support (D) Left Arm Front Left Leg Screws (G) Screws Right Arm(E2) C2 5. Connect the Support (D) to both the Left Arm (E) and Right Arm (E2). Insert one Bolt (I) and one Nut (I) through the Left Arm (E) and into the Support (D). Repeat for Support (D) and Right Arm (E2)-see Figure Connect the (A) to the Seat (B). Set the (A) so that the horizontal brace at the top-rear is resting on the top edge of the Supports (D). The bottom of the will rest on the Seat (B). Insert Screws (G) up through the (A) and Supports (D)-see Figure 5. Figure 6 Figure 5 (A) Screw (G) Left Arm (E) Support (D) Screws (G) Cross Brace (F) Seat (B) 6. Attach the front Cross Brace (F) to the and Front Left Leg (C and C2). Insert Screws (G) through the front and into the front of the Legs (C and C2)-see Figure Set up the Adirondack Chair and make certain it is square, level and stable. Make certain all hardware is fully tightened. Only use the Chair on a flat, level and solid surface capable of supporting the Chair and the person sitting in the chair. Parts List Part # A B C C2 D E Description Seat Front Left Leg Support Left Arm Quantity 2 Part # E2 F G H Description Quantity Right Arm Cross Brace Screw (4mm x 40mm)4 Bolt and Nut 0 (5.8mm x 55mm) I Bolt and Nut 2 (5.8mm x 65mm) Note: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. SKU For technical questions please call Page 4

5 Parts Diagram Bolt Washer Nut Bolt Washer Nut PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU For technical questions please call Page 5

ROLLER STAND WITH TWO-LEG SUPPORT ASSEMBLY AND OPERATING INSTRUCTIONS

ROLLER STAND WITH TWO-LEG SUPPORT 95621 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2006 by Harbor Freight