Workbench with peg board & drawer

Transcription

1 Workbench with peg board & drawer Model Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. Tools not included Mission Oaks Blvd., Camarillo, CA Visit our website at: To prevent serious injury, read and understand all warnings and instructions before use. Copyright 2006 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions or replacement parts, please call

2 Overall Dimensions Specifications 31-1/2 L x 16 W x 55 H Hooks Fit into Peg Board - Qty. 20 Peg Board Dimensions Drawer Weight Capacity Lower Shelf Weight Capacity Workbench Weight Capacity Upper Small Shelf Weight Capacity Overall Weight Capacity Weight 31-1/4 x 23-1/4 x 3/16 T 30 lb. 200 lb. 200 lb. 20 lb. 450 lb lb. Save This Manual You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Write the product s serial number in the back of the manual near the assembly diagram, or write month and year of purchase if product has no number. Keep this manual and invoice in a safe and dry place for future reference. GENERAL SAFETY RULES Keep your assembly area clean and well lit. Cluttered benches and dark areas invite accidents. Keep bystanders, children, and visitors away from the assembly area. Distractions can cause you to lose control. Keep children away from the Workbench and tools. Children should always be supervised when in the same area as the Workbench. Stay alert. Watch what you are doing, and use common sense when working. Do not assemble while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating tools may result in serious personal injury. Dress properly. Do not wear loose clothing or jewelry. Contain long hair, loose clothing, and jewelry when working with tools. Use safety equipment. Wear ANSI-approved safety goggles and heavy-duty work gloves when assembling. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. Maintain a safe working environment. Make sure there is adequate surrounding workspace. Do not assemble in a damp or wet location. Page 2

3 8. Do not exceed the weight capacity of the shelves and drawer of the Workbench or the overall weight capacity of this item. Overloading could cause the workbench to tip and cause bodily injury. Assembly Instructions Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. 1. Begin by arranging and organizing all the parts on a smooth surface on the floor. Be sure all the parts on page 8 are accounted for. If any parts are missing, contact Harbor Freight Tools at the phone number on the cover of this manual. Rear Post Extension (3) Rear Left Post (1) Figure Attach the Rear Left Post (1) to the Rear Post Extension Left (3). See Figure 1. Attach the Rear Right Post (2) to the Rear Post Extension Right (4), fastening the two side holes. Place the two Rear Posts on the floor with the sides having 10 holes facing down. Page 3

4 Center Beam (7) Bottom Beam (8) Top Shelf- Rear Beam (5) Figure Connect the Top Shelf-Rear Beam (5) to the two Rear Legs with Bolts (H). Fasten to top hole only on the Top Shelf-Rear Beam (5). The bottom hole will be used when the Peg Board (B) is attached. See Figure 4. Repeat, connecting the Center Beam (7) to the middle and the Bottom Beam (8) to the Legs. See Figure 4. Side Beams (11) Right Drawer Mount w/glide Rail (12) Side Beams (11) Side Beams (11) Left Drawer Mount w/glide Rail (13) 7. Figure 5 (8) Side Beams (11) Mount the assembled Center Beam (7) and the two Side Beams (11) at the center of the Leg assembly. Attach two Side Beams (11) to the Rear Leg assembly at the bottom. See Figure Attach the two Drawer Mounts w/glide Rails (12 & 13) to the Side Posts near the Center Beam (7). See Figure 5. Page 4

5 Center Beam (7) Front Right Bottom Beam (8) Post (15) Front Left Post (14) Black PVC Feet (G) Figure 6 Attach the Front Left Post (14) to the Drawer Mount with Left Glide Rail (13). Attach Side Beams (11) and the Center Beam (7) to the inside of the Front Left Post (14). See Figure 6. Repeat steps using the Front Right Post (15), attaching the Side Beams (11) and the Center Beam (7) to the inside of the Front Right Post (15). See Figure 6. Place the Black PVC Feet (G) on each leg. See Figure 6. Page 5

6 Peg Board and Top Shelf Assembly 1. In the bottom holes of the Top Shelf Rear Beam (5), attach the Peg Board (B). Use the longer Bolts (H), with the Washers (I) and Nuts (J). Use this hardware throughout the assembly of the Peg Board. Top Shelf Rear Beam (5) Top Shelf Beam (10) Top Shelf Beam (9) Left Post Extension (3) Peg Board (B) Top Shelf Front Beam (6) Rear Left Post (1) Figure 7 Attach the Peg Board (B) at the other eight connection points, use Bolts (H). See Figure 7. Attach the two Top Shelf Side Beams (9 & 10) to the rear legs. Attach the Top Front Shelf Beam (6) to the Top Shelf Beams. Assembly is almost complete. Drop the Top Shelf board (C) into the Top Shelf area. Drop the Work Top board (D) onto the top of the Workbench. Drop the Bottom Shelf (F) onto the bottom of the work bench. Hook the Hooks (A) into the Peg Board and hang your tools up for easy access. Page 6

7 Drawer Mounts with Glide Rails Drawer Installation / Assembly Drawer Guides Drawer Guides Figure 8 Attach the Front Drawer Panel (16) to the Side Drawer Panels (18 & 19) and the Side Panels to the Rear Drawer Panel (17). Tighten the Bolts (K), Washers (I), and Nuts (J). Drop the Drawer Bottom (E) into the frame of the Drawer assembly. Loosen all bolts on the workbench slightly. Slide in the drawer. Be sure everything is square, then tighten up the bolts all over the Workbench and check again to see that the drawer moves smoothly. Page 7

8 Latch Latch Figure 9 The drawers have a latch on each side. To remove the drawer, push the black latch down on the right and up on the left side of the drawer. See Figure 9. It is recommended that everything be removed before removing the drawer. Note: Follow all warnings before use. INSPECTION, MAINTENANCE, AND CLEANING BEFORE EACH USE, inspect the general condition of this product. Check for loose bolts, misalignment or broken parts, and any other condition that may affect its safe operation. Do not use damaged equipment. Keep the Workbench free of oil and grease to prevent accidents. Page 8

9 PARTS LIST Part Description Parts Drawing Q ty 1 Rear Left Post (35-1/4 ) 1 2 Rear Right Post (35-1/4 ) 1 3 Left Post-Extension (23-1/8 ) 1 4 Right Post-Extension (23-1/8 ) 1 5 Top Shelf Rear Beam (30-5/8 ) 1 6 Top Shelf Front Beam (30-5/8 ) 1 7 Center Beam (30-5/8 ) 2 8 Bottom Beam (30-5/8 ) 2 9 Top Shelf-Left Side Beam (4-1/4 ) 1 10 Top Shelf-Right Side Beam (4-1/4 ) 1 11 Side Beam (15 ) 4 12 Right Drawer Mount w/glide Rail (15 ) 1 13 Left Drawer Mount w/glide Rail (15 ) 1 14 Front Left Post (31-1/4 ) 1 15 Front Right Post (31-1/4 ) 1 16 Drawer Front Panel (20 ) 1 17 Drawer Rear Panel (20 ) 1 18 Right Drawer Panel (14-1/4 ) 1 19 Left Drawer Panel (14-1/4 ) 1 A Hook 20 B Peg Board (23-1/4 x 31 x 0.2 ) 1 C Top Shelf (4-1/4 x 31-1/4 x 0.25 ) 1 D Work Top (15-1/2 x 31 x 0.6 ) 1 E Drawer Bottom (14 x 28 x 0.25 ) 1 F Bottom Shelf (15-1/2 x 31 x 0.55 ) 1 G Black PVC Feet 4 H M6 x 15mm Bolt 6 I M6 Washer 70 J M6 Nut 70 K M6 x 12mm Bolt 64 Note: The lengths given are approximate. Page 9

10 9 3 H B D ASSEMBLY DIAGRAM 5 10 C A F 15 8 G Not all parts are shown in this drawing. Record Product s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product. In fact, the manufacturer and/or distributor expressly states that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all risk and liability arising out of his or her repairs to the original product or replacement parts thereto, or arising out of his or her installation of replacement parts thereto. Page 10