Chicken Coop OWNER S MANUAL

Transcription

1 Chicken Coop OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. -MODEL # YTF-200CC

2 Thank you very much for choosing this product! For future reference, please complete the owner s record below: Model: YTF-200CC Purchase Date: Save the receipt, the warranty, and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it. This product is designed for certain applications only. The manufacturer cannot be responsible for issues arising from modification. We strongly recommend that this product not be modified and/or used for any application other than that for which it was designed. If you have any questions relative to a particular application, DO NOT use the product until you have first contacted us to determine if it can, or should, be performed on the product. For technical questions, please call TECHNICAL INFORMATION Item Description Dimensions 61.4 x 26 x Construction Fir wood Nesting Areas 2 Roosting Bars 2 Hardware Stainless Steel Mesh Construction.8 mm wire Chicken Capacity 4 IMPORTANT SAFETY INFORMATION WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in serious injury. CAUTION: Do not allow persons to operate or assemble this product until they have read this manual and have developed a thorough understanding of how it works. WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions or situations that could occur. It must be understood by the operator that common sense and caution are factors that cannot be built into this product, but must be supplied by the operator. DO NOT: Allow children to play in, on, or around this product. SAVE THESE INSTRUCTIONS 2

3 WORK AREA Keep work area clean, free of clutter, and well-lit. Cluttered and dark work areas can cause accidents. Keep children and bystanders away while assembling this product. PERSONAL SAFETY Use safety apparel and equipment. Use safety glasses with side shields that comply with current national standards, while assembling this product. This applies to all persons in the work area. Also use non-skid safety shoes, hard hats, gloves, dust collection systems, and hearing protection when needed. CHICKEN COOP USE AND CARE Do not modify this product in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the equipment. There are specific applications for which this product was designed. Always check for damaged or worn-out parts before using this product. Broken parts will affect operation. Replace or repair damaged or worn parts immediately. ASSEMBLY Step #1: Attach the Front House Panel (H) and the Rear House Panel (I) to the Left House Panel (J) and the Right House Panel (K) using ten Screws (3). Right House Panel (K) Rear House Panel (I) Front House Panel (H) Left House Panel (J) 3

4 Step #2: Attach the Left Egg Box Panel (A) and the Right Nesting Box Panel (B) using four Bolts (1) and four Nuts (2). Left Nesting Box Panel (A) Right Nesting Box Panel (B) Step #3: Insert Nesting Box Floor Panel (E). Attach Nesting Box End Panel (C) to Left Nesting Box Panel (A) and Right Nesting Box Panel (B) using four Screws (6). Insert Nesting Box Partition (T). Nesting Box Partition (U) Nesting Box Floor Panel (E) Nesting Box End Panel (C) 4

5 Step #4: Attach Nesting Box Roof Panel (D) using four Screws (5). Nesting Box Roof Panel (D) Step #5: Install both Roosting Bars (Q) in slots located inside of the coop. Install Ramp (P) on side door frame. Slide in the Drawer Panel (O) through outside slot as shown. Roosting Bars (Q) Ramp (P) Drawer Panel (O) 5

6 Step #6: Attach the Left Pen Panel (L) and the Right Pen Panel (N) to the Pen End Panel (N) using four Screws (3). Left Pen Panel (L) Right Pen Panel (M) Pen End Panel (N) Step #7: Attach the Pen to the House on both sides as shown using eight Screws (5). 6

7 Step #8: Attach the Short Roof Panel (F) and the Long Roof Panel (G) using eight Screws (4). Short Roof Panel (F) Long Roof Panel (G) Step #9: Attach the Roof Cap (R) using two Screws (4). Roof Cap (R) 7

8 Step #10: Attach the Looped Door Handle (S) to the Looped Door Handle Rod (T) using one Bolt (7) and one Nut (8). Looped Door Handle Rod (T) Looped Door Handle (S) MAINTENANCE Cleaning Instructions: Clean with water and mild soap. Avoid harsh detergents. Dry completely. PARTS DIAGRAM 8

9 PARTS LIST Part # Description Qty. Part # Description Qty. A Left Nesting Box Panel 1 P Ramp 1 B Right Nesting Box Panel 1 Q Roosting Bar 2 C Nesting Box End Panel 1 R Roof Cap 1 D Nesting Box Roof Panel 1 S Looped Door Handle 1 E Nesting Box Floor Panel 1 T Looped Door Handle Rod 1 F Short Roof Panel 1 U Nesting Box Partition 1 G Long Roof Panel 1 1 Bolt, M6 55mm 4 H Front House Panel 1 2 Nut, M6 4 I Rear House Panel 1 3 Screw, M4 40mm 14 J Left House Panel 1 4 Screw, M3 25mm 10 K Right House Panel 1 5 Screw, M3 16mm 12 L Left Pen Panel 1 6 Screw, M4 35mm 4 M Right Pen Panel 1 7 Bolt, M4 10mm 1 N Pen End Panel 1 8 Nut, M4 1 O Drawer Panel 1 9 Hinges Latch 4 For technical questions, please call WARRANTY One-year limited parts warranty. BAC PO BOX 155 Miltona, MN Made in China 9