Boatwright Series: Building a classic Chaisson 10 Dory.
|
|
- Gerard Rich
- 5 years ago
- Views:
Transcription
1 Folk School Fairbanks Bruce Campbell, January through April 17, 2016 Boatwright Series: Building a classic Chaisson 10 Dory. The dory chosen for a glued lap construction using the Thomas Hill glued lap method, was originally built by George L. Chaisson of Swampscott Massachussets circa The round hull, multi-plank design is often referred to as a Swampscott Dory. The round hull is a more efficient displacement hull design than, for example, the simpler flat planked Grand Banks Dory. Examples of both are laid out by John Gardner in The Dory Book, The class relied on Gardner s illustrations, measurements, and table of offsets to recreate the craft. Classes included Lofting, or drawing full sized plans, constructing a mold from the lofted design, laminating the stem, fashioning a transom, attaching them to the bottom, planking the hull, and fitting outwale, inwale, and seat frames. Lofting the full size boat from the Table of Offsets. The skill allows the boat builder to choose from hundreds of designs without needing to buy patterns or kits. Larry Fogelson (with coffee), Stanley Madsen, Sarah Madsen (with hammer), Jason Fails far right.
2 Using the lofted half-breadth and heights to project the transom dimensions.
3 A batten is held to the nails and a fair curve is drawn to illustrate the hull. Jason Fails, Lorien, Sarah Madsen holding the sheetrock T-square, and Andy Reynolds far right. Using 16 gauge Raptor 5/8 long Composite nails to hold the planks while the epoxy cures. The composite nails can be planed or chiseled without damaging tools.
4 Jason Fails and Seth Wilson cleaning up epoxy squeeze-out between the bottom and the garboard planks.
5 Seth Wilson uses a heat gun to remove excess epoxy squeezed out between the bottom and the garboards.
6 Making the Gain Cut to blend the planks at the transom and stem. Adding sawdust thickened epoxy to the plank bevel and transom.
7 Attaching the epoxy coated plank #3 to underling glued beveled plank. (Planks are conventionally held in place with Lap Clamps. The class successfully tested the use of composite nails to hold the planks while the epoxy cures. The composite nails held sufficiently to allow one to attach more than one plank at a time, before the epoxy set. Bruce Stephenson, Stanley Madson, and Seth Wilson with nail gun. Bottom, Garboard (plank 1), Broadstrake (plank 2), and Binder (plank 2) are glued together and to the stem and transom. Removing the completed hull from the mold. The battens and mold stations are ready for use building the next hull.
8 Bruce Campbell sits in the completed hull prior to seats and trim. The strength of this construction style comes from the use of modern plywood and epoxying the beveled joints. The light weight results from the absence of ribs and stringers in the completed hull.
9 The outwale is clamped to the top sheer plank. Seat frames are clamped and epoxied in place.
10 The outwales and inwales are attached and join the transom with a knee fashioned to serve as a handle to lift the boat.
11 The bowplate or breasthook is clamped in place. First test run at Hamme Pool.
12 Stanley Madsen and Bruce Campbell at Hamme Pool. VeraAnn and Bruce Campbell, rowing, on the Tanana River, Alaska
13 Reindeer Hills, Nenana River, Alaska, summer 2016.
14 Fishing with the Chaisson 10 Dory, September, 2016, on Chena Lake, Alaska.
Building small wooden boats in Myanmar
39 12 ft & 18 ft Prepare bottom Before fitting the keel, there are several steps to complete: 1) Cut frame ends and transom to length (level with bottom). 2) Bevel bottom edge of lower side planks; this
More informationIllustrated Guide to Building a Spira International Ply on Frame Boat
Illustrated Guide to Building a Spira International Ply on Frame Boat Spira International, Inc. Huntington Beach, California Copyright, 2008 All Rights Expressly Reserved Building a Spira International
More informationBuilding small wooden boats in Myanmar
19 12 ft & 18 ft Fit remaining floors The remaining floors can now be cut to size by taking measurements at the boat. The timber required is given in step 1. See step 10, 11 and 20 for installation procedures.
More informationPhoto Essay Building a. Key Largo. Carolina Dory. Plans for this boat may be found at:
Photo Essay Building a Key Largo Carolina Dory Plans for this boat may be found at: http://spirainternational.com/ Photo Essay Building a Key Largo Carolina Dory The Carolina Dory is a specialized type
More informationPenobscot 14 Building Log
Penobscot 14 Building Log Date July 26, 2004 Duration Activity plane jig boards July 27, 2004 July 28, 2004 cut jig boards cut frame boards, assemble jig July 29, 2004 6.75 hr assemble jig August 2, 2004
More informationA Skin-on-Frame Pram. Designed by Dana Munkelt. Drawings by Andrew Walters. Duckworks Boatbuilder's Supply duckworksbbs.com
A Skin-on-Frame Pram Designed by Dana Munkelt Drawings by Andrew Walters Duckworks Boatbuilder's Supply duckworksbbs.com "" is a small skin-on-frame (SOF) pram design with a twist; a solid plywood floor.
More informationPoorBoy Skiff. A 10-11ft 6in skiff for outboard motoring By Steven Lewis
PoorBoy Skiff. A 10-11ft 6in skiff for outboard motoring By Steven Lewis PoorBoy is about the simplest small motorboat you will come across. It consists of 2-2 1/4 sheets of plywood (1-1 1/4 sheets x3/8
More informationBateau.com PH18 CNC kit notes 1/5
Bateau.com PH18 CNC kit notes 1/5 These building notes must be used in conjunction with the standard building notes included in the plans package for this boat. The PH18 kit is assembled as described in
More informationUse these notes in conjunction with the plans and the plan's building notes.
GF18 CNC kit notes. Use these notes in conjunction with the plans and the plan's building notes. The standard kit is based on the GF18 with the sole option, central bench included. There are small differences
More informationBuilding the Wee Lassie Canoe. A Michigan Woodworkers Guild Presentation by Bob Mills
Building the Wee Lassie Canoe A Michigan Woodworkers Guild Presentation by Bob Mills So you want to build a boat, eh? Ok, how about this for starters? Carved by Livio De Marchi, Woodcarver Extraordinaire
More informationPhoto Essay How to Build an. Alaskan. Grand Banks Dory. Plans for this boat may be found at:
Photo Essay How to Build an Alaskan Grand Banks Dory Plans for this boat may be found at: http://www.spirainternational.com/ How to Build an Alaskan Grand Banks Dory The Alaskan is an easy to build Spira
More information15-foot Gandelow Plans - Information about the contents of this free PDF
15-foot Gandelow Plans - Information about the contents of this free PDF CONTENTS Page 2: Views of the boat in plan, side view, from stem and stern and in 3D. Page 3: The dimensions of the 15-foot gandelow
More informationContents. Study Plans. 2 Introduction. 4 List of Materials. 5 Glue, Resin and Fixings. 6 Tools. 7 Construction Sequence
Volare Study Plans Contents 2 Introduction 4 List of Materials 5 Glue, Resin and Fixings 6 Tools 7 Construction Sequence Study Plans The study plans consist of an abridged version of the first 7 pages
More informationAbove are the offsets for the plywood panels.
DinkyDink Plans Bottom Panel Half Station X Y X2 Y2 1 1/4 3/4 0 11 5/16 2 4 9/16 4 12 9/16 3 11 11/16 1/4 11 7/16 14 1/2 4 18 5/8 1/16 18 5/8 15 11/16 5 25 3/4 0 25 3/4 16 5/16 6 32 13/16 0 32 13/16 16
More informationPhoto Essay: How to Build a. Seneca. Pacific Power Dory. Plans for this boat may be found at:
Photo Essay: How to Build a Seneca Pacific Power Dory Plans for this boat may be found at: http://www.spirainternational.com/ To begin building the Seneca, or any Spira International framed boat, a strongback
More informationContents. Introduction. List of Materials. Glue, Resin and Fixings. Tools. Construction Sequence. Study Plans Sheet 3. Andrew Walters April 2012
Mia Study Plans Contents C Andrew Walters April 2012 2 Introduction. 4 List of Materials. 5 Glue, Resin and Fixings. 6 Tools. 7 Construction Sequence. 10 Study Plans Sheet 1. 11 Study Plans Sheet 2. 12
More informationDelfini. 19x6 Console Semi Flat Hull. Study Plans
Delfini 19x6 Console Semi Flat Hull Study Plans Contents 3 Introduction 4 Specification 6 List of Materials 7 Glue, Resin and Fixings 8 Tools 9 Construction Sequence 2 Introduction This is the 19' x 6'
More informationStep 21. The second and third planks are fitted and fastened to the boat.
Step 21. The second and third planks are fitted and fastened to the boat. 22 A step-by-step guide to building a traditional double-ended timber fishing craft of Khmer (Cambodian) design Step 22. The planks
More informationHow to build a Javelin Skiff
How to build a Javelin Skiff This is not your grandfather s plywood boat! The Javelin involves a high-tech type construction, called composite. The hull can be constructed with foam or plywood; these materials
More informationYou start assembling the boat by piacing the buiiding board on two sawhorses as in Fig. 3. The lines marked on the building
ERE'S just what prospective builders of small sailboats have been looking for, as you will see from a glance at the facsimiles on the left, which reproduce excerpts from letters written by enthusiastic
More informationAN IMPROVED DESIGN FOR AMATEUR BUILDERS.. TAKES SAIL OR MOTOR
BUILDING A General H ERE is a rowboat that is in a class by itself the final development of a long line of forerunners. This graceful little V-bottom craft is 13 ft. long, carries from four to six passengers,
More informationBuilding instructions ARTEMIS Sailing Canoe Day Five Version 1.0 Brian Pearson & Dr. Axel Schmid Day Five. Assembly of Planks and Frames
Building instructions ARTEMIS Sailing Canoe Version 1.0 Brian Pearson & Dr. Axel Schmid 2016 Assembly of Planks and Frames Steps: Assembling hull plansk with wire Install frames Align and check keel rocker
More informationChapter Six. Getting started inboard. Installing the false deck
A close look at the thinning down of the bulkhead extensions. They are just 1/16 thick after fairing them. Chapter Six Getting started inboard This next step is one of the last remaining messy tasks to
More informationNZQA Expiring unit standard version 2 Page 1 of 5. Demonstrate knowledge of traditional wooden boatbuilding
Page 1 of 5 Title Demonstrate knowledge of traditional wooden boatbuilding Level 3 Credits 10 Purpose People credited with this unit standard are able to: describe the design evolution and development
More informationBuilding a Scarab 350 Trimaran
This boat was designed to be built using flat panels. In either foam laminated panels or plywood. 1. The build time is less. Panels are lofted, cut out and joined on the frame. 2. Frame can be simpler.
More informationBuilding Instructions ARTEMIS Sailing Canoe Day Six Version 1.0 Brian Pearson & Dr. Axel Schmid Day Six. Align and Glue Planks
Version 1.0 Brian Pearson & Dr. Axel Schmid 2016 Align and Glue Planks Steps: Align boat, check dimensions Join planks provisionally Pull wires Glue the outside planks Tools and Materials: Epoxy putty
More informationThis article was written by Phill Brander (AUS), who has built many timber catamarans including a Paper Tiger.
Building a Paper Tiger Catamaran Scarfing Plywood Paper Tiger Catamaran GUIDES Warnings/Cautions As always, using any power tools, cutting implements or adhesives carries certain risks. Make sure you understand
More informationRedwood strips are tacked to the templates, and edge-glued. Drive brads through into the templates before putting on fiberglass doth.
1 Make the building form and attach templates to the crosspieces. Nail a strip down the center to hold the stems and templates in position. prototype canoe took about three weekends to build. She's broad
More informationPart 2 Lining off and planking
Part 2 Lining off and planking Lining off the hull for planking Those of you who have built one of my projects in the past probably know how I have always stressed the importance of lining of your hull.
More informationArched. Building an. Passageway. Although my company specializes in high-end jobs
Building an Arched Passageway All photos by Brian Striegler This straightforward approach combines basic shop methods with simple site joinery to create an elegant frame-and-panel archway by Gary Striegler
More informationThe following pages replace pages 7 thru 14 in the current printing of BUILDING THE PT ELEVEN. (As of December 2012.)This is a modified method for
The following pages replace pages 7 thru 14 in the current printing of BUILDING THE PT ELEVEN. (As of December 2012.)This is a modified method for gluing puzzle joints that we believe is simpler than the
More informationDESIGN TO BUILD = BUILD TO DESIGN
DESIGN TO BUILD = BUILD TO DESIGN The following represents five days of work from demolition through layout of new flooring and wall frame and cabinetry Paul C. King, RA Associate Professor Department
More informationAuthors: Max Guzman, Donna Delahanty Guzman, Steve Hottinger. Teak & Aspen Sole Installation
Forward Authors: Max Guzman, Donna Delahanty Guzman, Steve Hottinger Teak & Aspen Sole Installation The original teak plywood floor on our 1976 T34C needed an extreme makeover. The dark stained areas refused
More informationInstalling your SHOE KEEL
Installing your SHOE KEEL The shoe keel is there solely to protect the bottom of the hull. On a windy day, it will offer some resistance to a side or quartering wind and will help to avoid being blown
More informationRestoration of 12½ -Footers
Restoration of 12½ -Footers Part II by Maynard Bray Photographs by Benjamin Mendlowitz here simply isn't enough space within the pages of WoodenBoat to describe everything Steve Ballentine does to bring
More informationLaminate Flooring Alternative to Hardwood Flooring
Laminate Flooring Alternative to Hardwood Flooring Laminate flooring is moderately expensive, with a cost generally between that of vinyl and hardwood flooring. It's easier to install than hardwood and
More informationPiper Cherokee /3 scale. Construction Manual
Piper Cherokee 140 1/3 scale Construction Manual STAB CONSTRUCTION 1. Remove foam cores from cradle and place on flat surface. Inspect pieces before you epoxy halves together making sure leading and trailing
More informationBuilding small wooden boats in Myanmar 12 ft & 18 ft Multi-purpose boats
12 ft & 18 ft Multi-purpose boats Immediate Rehabilitation of Subsistence Fisheries Livelihoods in Areas Affected by Cyclone Nargis (OSRO/MYA/805/SWE) Funded by the Government of Sweden Cover photograph:
More informationDuckSkiff. Specifications for motorized version: LOA: Beam: 5 2 (with trim) Depth at midships: 18. Draft at design weight of 860 lbs is 4.
DuckSkiff Duckskiff is a 14 foot skiff I designed for a buddy of mine named Tim that I work with. Tim is an avid Duck hunter and wanted a fairly lightweight boat but in nice quiet wood rather than noisy
More informationBuilding small wooden boats in Myanmar
60 12 ft & 18 ft Putty seams Putty is made up to a traditional recipe using a natural powder (see right) and oil, either cooking or diesel. The putty is rolled into lengths and worked into the seams. Note:
More informationSan Felipe: Step by Step Pack 3
Pack 3 Your parts Bulwarks Gun port covers x 2 Tools and equipment Wood glue Sandpaper Brushes Wood stain Hammer Pin pusher/nails Razor saw a Remove the longer bulwark and test-fit it in place at the bow
More informationTools and Tips: ( 1 )
Tools and Tips: As you build instructions will show in my many picture manual how to assemble. You can use your own methods as you desire, my results are very good. A smooth, flat work surface is very
More informationFINISH CARPENTRY. Installing Arched Casing How to make three different arched trim details look like they grew there
FINISH CARPENTRY 1 2 3 Installing Arched Casing How to make three different arched trim details look like they grew there Photos by Gary Striegler BY GARY STRIEGLER I love the challenge of trimming arched
More informationCOMPONENTS OF THE CLICKFAST FASCIA AND GUTTER SYSTEM 5: INTERNAL MITRE
INTRODUCING THE CLICKFAST FASCIA AND GUTTER SYSTEM The Clickfast Fascia and Gutter System was originally designed by Stratco and has proven to be the most successful fascia and gutter system in Australia
More informationChapter Four, Fitting out the Shell
Chapter Four Fitting out the Shell This chapter outlines the process for fitting the parts that go into a round or stave back shell. Square back sound boxes usually have the cap and base of the sound box
More informationCowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers
Cowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers for up to date building information; http://www.mikenchell.com/forums
More informationDemilune 4. Apron Joinery. Curved Apron Tenon. Bridle Joint Legs. Bridle Joint Front Apron
Demilune Email 4 Apron Joinery There are two types of joints used in connecting the aprons and legs. The rear legs use conventional mortise and tenon joints, while the front legs use the less conventional
More informationNEW equinox INSTALLATION GUIDE Issue
NEW equinox INSTALLATION GUIDE Issue 1 CONTENTS If in doubt at any stage 1. Preparing the ring beam 2 2. Installing the framework 3 3. Insulation and waterproofing 7 4. Tile application: Steel tiles 9
More informationG. Building the Cab, Cab Roof and Cab Boiler Extension Page 14 and Backhead.
G. Building the Cab, Cab Roof and Cab Boiler Extension Page 14 and Backhead. Cab. In order to ensure that the cab and tender would actually look right, as what often appears on a drawing is not always
More information(1) C & C 30 MK I I. Building the Wine Glass Holder
(1) C & C 30 MK I I Building the Wine Glass Holder 1. This package contains instructions and sketches plus scanned pictures. 2. Woodworking skills and equipment are essential to make the pieces and assemble
More informationA H M 531 The Civil Engineering Center
Table of Contents contents Page Introduction 1 Objectives 2 Background 2 Apparatus and tools 3 Requirements 5 Procedures 6 Conclusion 10 References 10 1 Introduction Carpentry work is one of the most important
More informationBuilding Instructions ARTEMIS Sailing Canoe Workshop and Tools Version 1.0 Brian Pearson / Dr. Axel Schmid Two Sawhorses. Workshop and Tools
Building Instructions ARTEMIS Sailing Canoe Two Sawhorses Workshop Yes, you can build the ARTEMIS sailing canoe in the garage, with good lighting, and assuming a power supply. To have room to work it needs
More informationM. R. Mittleman, Constructor Member, Long Island Woodworkers
M. R. Mittleman, Constructor Member, Long Island Woodworkers You wanna do what??? February 24, 2016 Long Island Woodworkers Presentation 2 Some particulars about the craft to be constructed: Model name
More informationTAPE & GLUE PROCESS Version: Jun. 2011
FREE to print TAPE & GLUE PROCESS Version: Jun. 2011 The following small boat assembly process was developed out of the need for an easy, lightweight, cost effective and health friendly method of providing
More informationCAUTIONS / INSTRUCTIONS
CAUTIONS / INSTRUCTIONS EPOXY Epoxy is used for many purposes in the building of your boat. It is used to join wood, bond fiberglass, fill gaps, and seal the wood. We supply epoxy from Raka Boat Building
More informationCARPENTRY AND JOINERY
EXAMINATION SCHEME CARPENTRY AND JOINERY There will be three papers, Papers 1, 2 and 3, all of which must to be taken. Papers 1 and 2 will be a composite paper to be taken at one sitting. Paper 1: Paper
More information1982 Hydrostream Viking Restoration
1982 Hydrostream Viking Restoration Part 2a: The Rebuild Daniel W. Rickey Winnipeg, Manitoba Canada daniel@cancercare.mb.ca 2000-07-19 Introduction Part one of this report showed how the shoddy manufacturing
More informationAdditions/Corrections to the 14-Foot Brockway Construction Guide. Timothy C. Visel, May 2008 The Sound School Adult Education & Outreach Program
Additions/Corrections to the 14-Foot Brockway Construction Guide Timothy C. Visel, May 2008 The Sound School Adult Education & Outreach Program Building a 14-Foot Brockway by Tim and Willard Visel In 2005,
More informationTools and Tips: ( 1 )
Tools and Tips: As you build instructions will show in my many picture manual how to assemble. You can use your own methods as you desire, my results are very good. A smooth, flat work surface is very
More informationMaking a Greenland Paddle - New Zealand style
Making a Greenland Paddle - New Zealand style ~by Sandy Ferguson The following describes how to make a paddle reasonably easily and with as little wastage as possible. This could be your first Greenland
More information2017 VCE VET Furnishing examination report
2017 VCE VET Furnishing examination report General comments The 2017 VCE VET Furnishing examination assessed students underpinning knowledge of the competencies they had undertaken in Units 3 and 4 as
More informationBuilding without Staples
Building without Staples Equipment List Photo #1 32-40 L or U-shaped jigs (see instructions below) 32-40 1 and 2 inch C-clamps 4 6 12 inch F-clamps or QuickGrips 4-6 6 inch QuickGrips 5-10 bungies cords
More informationBuild your own Drawer unit. D3 / D4
Page1 Build your own Drawer unit. D3 / D4 1: Introduction. This guide will give you the plans, materials and how to information to build your own drawer unit. The dimensions given will fit a D3 or D4,
More informationPROJECT PLAN MODERN COFFEE TABLE
BUILD IT WITH ROCKLER PROJECT PLAN MODERN COFFEE TABLE With its clean lines and striking geometry, this coffee table will lend iconic midcentury modern style to any living space. And you can build it yourself
More informationWood Flooring Collection. Bringing affordable style to any home
Wood Flooring Collection Bringing affordable style to any home 2 Product Options Multiply - Featuring a top surface of solid wood bonded to multiple layers of cross-laid ply to create a highly stable hardwood
More informationClassic Kitchen Island
America s leading woodworking authority Step by Step construction instruction. A complete bill of materials. Classic Kitchen Island Exploded view and elevation drawings. How-to photos with instructive
More informationGENERAL NOTES: Page 1 of 9
Laminating A Zia Into A Turning Blank by W. H. Kloepping, Jan. 2009 This describes how a zia (the New Mexico state symbol) can be laminated into a turning blank. Materials needed: Square Turning Block
More informationInstallation Guide 2016
Installation Guide 2016 BUILDERS EDGE INSTALLATION GUIDE This guide will show you the products of the Builders Edge family. It provides specific installation steps and application details. Our main goal
More informationHow to build the QUICK CANOE 155
How to build the QUICK CANOE 155 DESIGNER Michael Storer storerm@storerboatplans.com www.storerboatplans.com Michael Storer 2010 Page 2 TABLE OF CONTENTS LICENCE Quick Canoe 155...4 Internet information...4
More informationNEW equinox INSTALLATION GUIDE Issue
NEW equinox INSTALLATION GUIDE Issue 2 CONTENTS 1. Preparing the ring beam 2 2. Installing the framework 3 3. How to install structural support posts 7 4. Insulation and waterproofing 8 5. Tile application:
More informationROOF FRAMING INFORMATION BATTEN INSTALLATION CORONA SHAKE INSTALLATION ACCESSORY INSTALLATION ESTIMATING DATA GENERAL INFORMATION
ROOF FRAMING INFORMATION BATTEN INSTALLATION CORONA SHAKE INSTALLATION ACCESSORY INSTALLATION ESTIMATING DATA GENERAL INFORMATION ROOF FRAMING INFORMATION It is the responsibility or roofers, building
More informationSAN FELIPE: Step by Step Pack 2
Pack 2 Your parts Stern reinforcement Bulkheads The poop deck Bulkhead planks Planks Tools and equipment Knife Pencil Wood glue Sandpaper File a Using leftover 5 x 5-mm wooden strips, measure and cut beams
More informationBuilding a Sawbench. Precision Sawing at The Woodwright's School August 2010
Building a Sawbench Precision Sawing at The Woodwright's School August 2010 Introduction: Though I work with both machinery and hand tools, I consider a pair of traditional old-school sawbenches to be
More informationBuilding an Unfeathered Paddle with a Wood Shaft and Carbon Fiber Blades
Building an Unfeathered Paddle with a Wood Shaft and Carbon Fiber Blades by Duane Strosaker Choosing the Wood Two 3/4" pieces of Sitka spruce laminated with epoxy for an unfeathered one-piece paddle. For
More informationMGB Warpath Rigger Building Instructions (Rev )
MGB Warpath Rigger Building Instructions (Rev. 2012-05-01) Thank you for choosing the Warpath Rigger. We have worked hard to make this kit as easy as possible to assemble while maintaining a high level
More informationTripanel Marine Technical Bulletin
Tripanel Marine Technical Bulletin Figure 1 Cabinet joints can be accomplished by four methods: a) rabbet one panel to the proper thickness of joining panel and epoxy joint b) dado to thickness of joining
More informationShingle Installation Guide
Installation Guide Roof Framing Information Installation Installation Accessory Installation Estimating Data General Information Roof Framing Information It is the responsibility or roofers, building contractors
More informationSTICK 2 IT. Fuselage Construction:
RCCD 2014 CLUB PROJECT STICK 2 IT Fuselage Construction: The fuselage is constructed without the use of a set of plans. The fuselage will be constructed on your previously prepared work surface and by
More informationIntroduction: The model should be assembled following the sequence of the stages of construction described in these instructions.
Victoria Bestell-Nr. 3082/00 Introduction: The model should be assembled following the sequence of the stages of construction described in these instructions. The laser-cut components are individually
More informationLetter STUDENT NUMBER VCE VET FURNISHING. Written examination. Friday 17 November 2017
Victorian Certificate of Education 2017 SUPERVISOR TO ATTACH PROCESSING LABEL HERE Letter STUDENT NUMBER VCE VET FURNISHING Written examination Friday 17 November 2017 Reading time: 9.00 am to 9.15 am
More informationAlaska Bird Observatory Shelves Christopher Swingley
Introduction Alaska ird Observatory Shelves Christopher Swingley These are the bookshelves I built for the Alaska ird Observatory s new building at Wedgewood Resort in Fairbanks. My version was built from
More informationMaking your Rudder Cassette
Making your Rudder Cassette A list of the stuff you ll need The row of materials below is laid out in the order of application. The foam blank shown on the right is available from Bob at www.flyingfoam.com
More informationInstall Windsor Corners
Install Windsor Corners Tools and Supplies You'll Need 1. Exterior Grade Screws use screws that are long enough to go through the FauxPanel and firmly attach to the wall behind the FauxPanel. We recommend
More informationReal Good Toys 10 Quarry St Barre, VT
Real Good Toys Special Edition Kit #SE-RR 29 /5 Congratulations on your choice of a Real Good Toys product. Your kit has been precision made with meticulous care by our craftspeople using carefully selected
More information!! " # $ % & '! ( ) * +, -
!! " # $ % & '! ( ) * +, - North Pegasus This carton contains: (1) Instruction package. Response Curves North Creek Cabinet Handbook North Creek Wiring Guide (2) 6 oz. Rolls of Dacron stuffing. (1) Tube
More informationA Canadian Canoes Information Sheet MAKING A STRONGBACK USING MANUFACTURED I-BEAMS
A Canadian Canoes Information Sheet MAKING A STRONGBACK USING MANUFACTURED I-BEAMS BACKGROUND: We have worked with Ted Moores (author of CANOECRAFT and KAYAKCRAFT ) for 28 years. For most of that time,
More informationCorner Cupboard. This space-saving piece enhances any room 46 FINE WOODWORKING
Corner Cupboard This space-saving piece enhances any room BY G A R R E T T H A C K On every trip to the Shelburne Museum near Burlington, Vt., I visit a favorite object a small hanging corner cabinet.
More informationBUILDING A SELMER MACCAFERRI GUITAR
BUILDING A SELMER MACCAFERRI GUITAR A step-by-step guide to building a laminated body Selmer-Maccaferri guitar Michael Collins The Heel The heel should now be prepared to be glued to the neck shaft. Using
More informationBuilding The Precedent Perkasa. By Dave Kershaw
Building The Precedent Perkasa By Dave Kershaw Kit Contents Here you can see the original 1/32nd scale kit from Precedent. It includes a nice instruction booklet with some essential photographs, plenty
More informationThe Use of Collapsible Molds for Violins, Cellos, and Basses: Resolution of Two Common Variations on the Inner Mold
The Use of Collapsible Molds for Violins, Cellos, and Basses: Resolution of Two Common Variations on the Inner Mold MIKE CARLSON, ROSS HILL, AND DON KENNEDY INTRODUCTION This article represents a written
More informationRECESSED SKIN FITTINGS
RECESSED SKIN FITTINGS Designed and made in New Zealand, Tru-Design Recessed Skin Fittings are the superior composite thru-hull solution for reduced drag. Skin Fitting Recessed Skin Fitting The Recessed
More informationESL - DESIGN AND TECHNOLOGY / TECHNICS HANDTOOL IDENTIFICATION AND TERMINOLOGY
ESL - DESIGN AND TECHNOLOGY / TECHNICS HANDTOOL IDENTIFICATION AND TERMINOLOGY One of the biggest difficulties in teaching ESL students practical skills is the lack of exposure to related technology and
More informationGreene & Greene. Mailbox. by Seth Keller. Signature details create an elegant box. 2 AmericanWoodworker.com
Greene & Greene Mailbox by Seth Keller Signature details create an elegant box. 2 AmericanWoodworker.com We needed a new mailbox, but I couldn t find an off-the-shelf version that I liked. So I decided
More informationWhat to expect - The basic building process, time and costs
Chapter One What to expect - The basic building process, time and costs Most prospective builders seem intimidated with this process. None of the steps are that difficult If anything, the hardest part
More information*Before starting, please read entire manual *Changes can be made in order for this manual to work for you. 3 x 6 I-Beam
*Before starting, please read entire manual *Changes can be made in order for this manual to work for you 3 x 6 I-Beam Follow all applicable sections of the attached Manufacturing Plan. Objectives: Understand
More informationBluenose II Part 2. Planking the Hull
Planking the Hull Planking is time consuming and requires care, but it can be very satisfying to watch your creation take shape. It is also the point at which many would-be ship modelers throw up their
More informationTHE SWALLOW. An interesting, simple, all-balsa speedster of crashproof design. by MALCOLM J. ABZUG
THE SWALLOW An interesting, simple, all-balsa speedster of crashproof design. by MALCOLM J. ABZUG DESIGNED primarily for the purpose of testing a new type of monocoque fuselage design, the Swallow proved
More informationDeck Repair Grady White Runabout
Deck Repair Grady White Runabout An older Grady White runabout with pedestal mounted captains chairs had suffered a structural failure at one of the pedestal bases. The deck in this area was cored. Inadequate
More informationMudroom Unit. Page 1 of 25
Mudroom Unit www.andrewharriswoodwork.com Page 1 of 25 Introduction This plan makes a unit which is 66 ¾ inches tall, 39 ½ inches wide and 18 ½ inches deep. It was custom made for some friends to fit the
More informationCarry out structural carcassing operations
Reference : K/504/7882 Level : Level 2 Credit Value : 16 Carry out structural carcassing operations Guided Learning Hours : 128 Grading Type : Graded Aim : The aim of this unit is to provide the learner
More information