Under the Bark Where the good stuff is, peel it back or use it as an accent.
|
|
- Jessie Perkins
- 5 years ago
- Views:
Transcription
1 Under the Bark Where the good stuff is, peel it back or use it as an accent. Newsletter for June, 2015 Club officers for 2015 President: Vice President: Secretary: Treasurer: Susan McCoy Brian Malnar Kevin Johnson Trudy Webb Advisory Board Aaron Cornell Rich Froelich Librarian: Directory: Web: Newsletter: Casey Goold Rich Howard Marlene Knopp Don Thompson Casey Goold Ellis & Marcia Miller
2 Demonstration by Wayne Rexford Finials Wayne started his demonstration by reminding everyone that he is a retired math teacher. He prepared a math lesson for us. Wayne asked, How do you divide a fraction in half. Wayne, I get my construction calculator out. But Wayne had a simple way to figure out the half of any fraction. Then he added how to figure out the half of a whole number with a fraction. Wayne said there would be a quiz later. Can t get the teacher out of him, but onto his lesson on finals. Wayne said there will be a pop quiz later. Wayne brought several Christmas ornaments that he has made and the finals that he attached. Picture #1 Picture #2 Picture #3 Picture #4 2
3 Wayne also brought in a scoop and the jig he made to mount the scoop, and a offset pendent jig. Wayne drilled two 5/16 holes, 3/8 on center. Wayne said that he will make inside out turnings (page 2, pictures #1,3 and 4) as well as hollowed ornaments (page 2, picture #2). On page 2, picture #3 Wayne added some veneer to the outside of the turning for a different look. The ornament in picture #2 rattles. When Wayne hollowed it, he wanted everyone to know it was hollow, so he put some dried beans inside the ornament. As light as that ornament is, I think almost everyone would know it was hollowed out, and not solid wood. From concept, wood selection, design and turning, this is a first class ornament. Excellent job Wayne! Wayne made his own drive center for turning the ornaments. He used a 1/4 bolt and ground a spur on one end. He uses a drill chuck to hold the custom made spur. Wayne gets idea s for finials from the front legs of antique furniture, fellow turners or from doodling to make his own designs. 3
4 He will make different finials and fit them into a turned ornament to see how they look. If the finial looks heavy with the ornament, you can adjust it right away. If the finial doesn't look big enough for the ornament, you can make a new one at that point. Then Wayne said, What is half of 1 7/8?. Several people quickly came up with the answer. He then went on to talk about how he holds his reverse turned finials in a chuck. Then Wayne said, What is half of 37 5/8? Where is my calculator? Oh well, someone please, pop up with the answer. A few words of advise from Wayne, when sanding reverse turned projects, be sure to use a strip of sand paper from a roll. Wayne, thank you for a great demonstration. I have committed to making some Christmas ornaments and you have got the thought process started. I was not considering a reverse turned ornament, but now I will look at it more. Here are a few other pictures of things Wayne used in his demonstration. 4
5 Show and Tell Aaron Cornell brought in a ball jig that he made. Aaron laminated plywood together to make the frame. He went to School Supply in Boise and bought one foot of key stock. He mounted a round easy-wood cutter on the key stock. He built a base to fit his lathe. He used two bearings, top and bottom that are held in place by a bolt. Results are a very good ball jig. Aaron made a chuck for his vacuum chuck to hold the balls for finish turning. One of the balls is on top of the chuck. Another project from Aaron s ball jig. Golf anyone? 5
6 Ken Smith got very busy with his Sorby spiral tool, and completed two excellent projects. The wood is Osage Orange. The pictures below are on a Maple bowl using the texturing tool John Pickrell made the vases. They are 11 inches high. To quote John, I gave birth to two more vases. John, was it a hard delivery? Excellent vases John, and thank you for sharing with the club. 6
7 Danny Kunz brought in three pieces, a small goblet, a larger goblet and a lidded box. The small goblet to the right has a quarter in front of it. The wood is Lignum Vitae. This goblet is a little larger than the above goblet. It is made from flowering plum. The lidded box is made from flowering plum. While Danny was turning the box he had a crack develop. Danny used a Dremel tool to widen the crack. He then filled the crack with brass filings. Thin CA glue was put on the filing and sanded until finished. Danny, I have tried to do some very small piece s, but I always found it hard to get a good balance between the top and base, not much room to get it right; easy to get it wrong. You have done an excellent job. Keep up the good work and thanks for showing your work and explaining your technique for repairing a crack. 7
8 Rich Froehlich continues with his casting venture. A friend of his sent him some heat treated sage brush. Rich cast different colors with a piece of wood in the mold. The results were a beautiful handle on the ice cream scoop and bottle stopper. Rich, does this mean you will be serving ice cream at our next meeting, or how about the picnic?. Rich put a Banksia pod in the center of the bud vase. While Rich was turning the vase, he had to keep taking off the surface of the Banksia pod which resulted in the concave taper on the outside. Rich designed in a glass vase tube, so you can put water in the vase for the flowers. Rich, it is great to see you expanding out from pens. Your casting work got really good, really fast. Thank you for showing your work. 8
9 Susan is going to attend the AAW symposium in Pa. this year. The women in turning group decided to make eggs to auction off. Susan brought in several eggs that she was making, and some of them failed. You can see the progression of the eggs. Remember Wayne s demo? He started with an idea and progressed with the idea until he had a finished project. This is how all of the top turners develop a project. What you see displayed is not the first one they have made. The lessons learned from Wayne and Susan made it well worth attending the meeting. Same egg, different views. Susan was given a couple of boxes of free wood. She found a nice piece of purple heart and she decided to make a satchel with a wood clasp on the top. She cut it in half and glued it together with newspaper (she learned she should have used brown paper from a shopping bag) so she could separate them after turning the handle. Susan got so excited about finishing the ends, she cut off the end pieces that she planned to use to split the two pieces. She found it was hard to break the glue joint. She soon figured out that she could open the glue joint with a chisel, then hide the damage with the satchel cloth; problem solved. A highly skilled artist like Susan can solve her problems and you never see it. 9
10 Bowl exchange Don Thompson made the bowl for the bowl exchange. Wow, what a neat bowl. Creative juices overflowing with this one. Don mounted the wood using a screw chuck drilled into one of the corners. 10
11 Raffle fun Birch, Diagonal cut pen blanks Point tool Point tool Cedar pen blanks Shop lamp Cherry Walnut pen blanks Honey locust pen blanks Parting tool Magnet on a extension shaft 11
12 Happy raffle winners There is another winner who s picture I didn t get who was the winner of the bowl exchange; sorry. 12
13 Monte's visit Monte showing the bottle opener template Template with the bottle openers Woodcraft is now carrying the Razertip line of pyrographic tools T-handle storage box. Quality woodturning tools Credit card size diamond sharpeners 2 piece diamond sharpening set. Quality woodturning tools; great price s. Credit card size diamond sharpeners 13
14 Club business Marlene said that she is still looking for the Richard Raffan, Turning Wood CD. It has been missing for many month s. All fine s for the CD s return have been waved. Please return the CD to Marlene at the next meeting. The club has an excellent library of CD s and book s that are available for any club member to check out. A list of what is available is on the web site. See Marlene before the meeting to check out items. Please return the item at the next meeting. There is no charge for the first month. If you fail to bring back the item after the first month, there will be a $5.00 late fee for each month you have the item. Micheal Kingsley will be giving a seminar at Woodcraft on sketch-up, and how it will help in woodturning. The seminar will cost $5.00 and will last about two hours. The summer picnic will be at Micheal Kingsley s house on Aug. 15 at 4:00 PM. It will be a pot luck. More information at the next meeting. There will not be a club meeting in Aug. 14
Southwest Idaho Woodturners Association The Treasure Valley Woodturner s club Meets monthly on the 2 nd Tuesday at 6:30 PM At the Woodcraft store in Boise ID. 7005 W. Overland Rd Boise ID. http://www.swiwt.com/.
More informationSouthwest Idaho Woodturners Association The Treasure Valley Woodturner s club Meets monthly on the 2 nd Tuesday at 6:30 PM At the Woodcraft store in Boise ID. 7005 W. Overland Rd Boise ID. http://www.swiwt.com/.
More informationSouthwest Idaho Woodturners Association. August 2017
Southwest Idaho Woodturners Association The Treasure Valley Woodturner s club Meets monthly on the 2 nd Tuesday at 6:30 PM At the Woodcraft store in Boise ID. 7005 W. Overland Rd Boise ID. http://www.swiwt.com/
More informationMinutes/Newsletter of Space Coast Woodturners April 8, 2015
Minutes/Newsletter of Space Coast Woodturners April 8, 2015 Submitted by Dotty Pugh Secretary Just a reminder the meetings are held on the second Wednesday of the month from 7:00 9:00 PM and the handson
More informationAugust 6, The demonstrator will be Steve Cook.
www.brasstownwoodturners.org Next meeting is: Terrence Powell BWG News Editor terrence.powell1963@gmail.com August 6, 2016. The demonstrator will be Steve Cook. $10 fee at the door to all attending Steve
More informationBetween Turns. May Stump The Pro... Upcoming Dates. Michigan Association of Woodturners A chapter of the American Association of Woodturners
Between Turns C O N T A C T U S : President: Michigan Association of Woodturners A chapter of the American Association of Woodturners Tom Mogford 810-629-6176 Vice President: V O L U M E 2 2, I S S U E
More informationEchos From the BAT. Cave. David Ellsworth. Baltimore Area Turners. Inside this issue: David Ellsworth 2 D&D Log Cradle 5 Other Stuff 6.
Echos From the BAT Baltimore Area Turners Cave March, 2012 David Ellsworth Inside this issue: David Ellsworth 2 D&D Log Cradle 5 Other Stuff 6 2012 Officers: In March, BAT was graced with a visit by Grandmaster
More informationSouth Central Pennsylvania Wood Turners Club
South Central Pennsylvania Wood Turners Club 18 Water Street, Jacobus, PA 17407 President Bill Krofft wkrofft@hotmail.com (724) 504-5565 Vice-President Tom Deneen Tomdeneen@emailaccount.com (717) 927-9004
More informationClay Foster Demonstration topics
Clay Foster Demonstration topics Rotation #1: Low-tech surface enhancement An array of surface enhancement techniques that don t require a large investment in tools, materials, or skills will be presented.
More informationCICAAW Turnings. Next month, Jim Dupler is going to mystify us with a tool handle creation demo.
Central Indiana Chapter of the American Association of Woodturners CICAAW Turnings FEBRUARY 2018 January Meeting Notes and Upcoming News The official meeting began at 2p.m. at the Zionsville Boys and Girls
More informationCICAAW NEWSLETTER. Website CICAAW.org. What s Inside This Issue. Central Indiana Chapter of the American Association of Woodturners April 2018
Central Indiana Chapter of the American Association of Woodturners April 2018 CICAAW NEWSLETTER Officers President: Jim Dupler jdupler01@comcast.net Vice President: 765-860-7036 rddlpark@yahoo.com Treasurer:
More informationCape Cod Woodturners Minutes and News May 6, 2015
Cape Cod Woodturners Minutes and News May 6, 2015 The May meeting started at 6:40 following a pre-meeting hands-on demo by Jim Silva and tool sharpening tutoring by Mike Grady. President Clarke Buchanan
More informationCICAAW NEWSLETTER. Website CICAAW.org. What s Inside This Issue. Central Indiana Chapter of the American Association of Woodturners March 2018
Central Indiana Chapter of the American Association of Woodturners March 2018 CICAAW NEWSLETTER Officers President: Jim Dupler jdupler01@comcast.net Vice President: Rich Parker 765-860-7036 rddlpark@yahoo.com
More informationA candle stick addresses transferring and reproducing dimensions from a plan and breaking the project into steps.
Activities Discussion These projects allow more skill development including making items to match a drawing, sizing projects to specific dimensions, and just trying fun stuff for the first time! A candle
More informationDemo of the Month. Officers & Contacts
Volume 1 Issue 1 March 2012 American Association of Woodturners Chapter Since May 2010 Officers & Contacts CEDAR CITY AREA: PRESIDENT: Will Arcularius (805) 712-2174 arcwerks@scinternet.net VICE PRESIDENT:
More informationMinutes/Newsletter of Space Coast Woodturners January 14, 2015
Minutes/Newsletter of Space Coast Woodturners January 14, 2015 Submitted by Dotty Pugh Secretary Just a reminder the meetings are held on the second Wednesday of the month from 7:00 9:00 PM and the handson
More informationThe following is the process of preparing the making the wedge ornament
Wedge Christmas Ornament The following is the process of preparing the making the wedge ornament Setting up your saw to cut true 11.25 degree angles for a 16 piece to make a circle that will form the globe
More informationAlabama Woodturners Association
Alabama Woodturners Association April 2019 A member of the American Association of Woodturners Meeting location: Homewood Senior Center, 816 Oak Grove Rd., Homewood, AL 35209 Meeting time: The second Saturday
More informationPresident George Paes
President George Paes 805 929 1423 V. President Gprdon Rowland 805 929 1423 Treasurer Terry Cohen 805 747 4584 Librarian Don Barr 805 226 8252 Next Meeting Saturday June, 11th Odd Fellows Hall; 520 Dana
More informationEchos From the BAT. Cave. Woodworking Show. Baltimore Area Turners. Inside this issue: Woodworking Show 2 Show and Tell 3 Gallery 5 Other Stuff 6
Echos From the BAT Baltimore Area Turners Cave January, 2012 Volume 7, Number 1 Woodworking Show Inside this issue: Woodworking Show 2 Show and Tell 3 Gallery 5 Other Stuff 6 2012 Officers: For the 3rd
More informationDemonstration Bob Rosand October 20, 2007 by Bob Gunther
Demonstration Bob Rosand October 20, 2007 by Bob Gunther Overview: Bob Rosand has been a woodturner for more than 25 years. He teaches, demonstrates and writes articles on many topics pertaining to woodturning.
More informationBetween Turns. August Upcoming Dates. Michigan Association of Woodturners A chapter of the American Association of Woodturners
Between Turns C O N T A C T U S : President: Tom Mogford 810-629-6176 Vice President: Bill Magee 734-981-6117 Michigan Association of Woodturners A chapter of the American Association of Woodturners V
More informationBetween Turns. July Upcoming Dates. Michigan Association of Woodturners A chapter of the American Association of Woodturners
Between Turns C O N T A C T U S : President: Michigan Association of Woodturners A chapter of the American Association of Woodturners Tom Mogford 810-629-6176 Vice President: V O L U M E 2 3, I S S U E
More informationThe Turning Point. The newsletter of the Siouxland Woodturners Chapter of the American Association of Woodturners
The Turning Point April 2009 The newsletter of the Siouxland Woodturners Chapter of the American Association of Woodturners News from your President It appears that spring might finally be here! I know
More informationECHOES FROM THE BAT CAVE
ECHOES FROM THE BAT CAVE Bowl From a Board - Joe Kramer March 2019 Joe Kramer, from Chesapeake Woodturners was our demonstrator for March. Joe presented his techniques for creating a bowl from a board,
More informationBetween Turns. March 2012 Meeting... Upcoming Dates. Michigan Association of Woodturners A chapter of the American Association of Woodturners
Between Turns C O N T A C T U S : President: Michigan Association of Woodturners A chapter of the American Association of Woodturners Tom Mogford 810-629-6176 Vice President: V O L U M E 2 4, I S S U E
More informationEchos From the BAT. Cave. Hands On. Baltimore Area Turners. Inside this issue: Hands On 2 Book Review 5 Other Stuff 6.
Echos From the BAT Baltimore Area Turners Cave April, 2012 Hands On Inside this issue: Hands On 2 Book Review 5 Other Stuff 6 2012 Officers: April s Hands On session featured Green Wood Bowl turning, Spindle
More informationWOODTURNERS OF ST. LOUIS
WOODTURNERS OF ST. LOUIS A Chapter of the American Association of Woodturners February 2006 WOODTURNERS OF ST. LOUIS AT THE COLLINSVILLE WOODWORKING SHOW Last weekend, if you had the chance to make it
More informationThe Nutmeg. Newsletter of the Nutmeg Woodturners League Established June 14, NEXT MEETING March 13, 2017
The Nutmeg Newsletter of the Nutmeg Woodturners League Established June 14, 1989 Volume 30, No. 2 March, 2017 www.nutmegwoodturners.com NEXT MEETING March 13, 2017 Program: Favorite Jigs and Fixtures Demonstrator:
More informationWoodworkers Guild of Southwestern Michigan April 2014
Woodworkers Guild of Southwestern Michigan http://www.woodguild.org April 2014 Next Meeting April 8, 2014 7:00pm Al Collison s Shop at 10292 Douglas Ave. Take Douglas North to Cooper, it is 2 ½ miles North
More informationMarch 2, 2018 Demo. Nick Agar. Turning a Lidded Bowl with Finial. Join us at the Bemis School of Art
March 2018 March 2, 2018 Demo Nick Agar Turning a Lidded Bowl with Finial Join us at the Bemis School of Art PPW dues are $30/year. Dues are used for guest demonstrators, purchase and maintain club equipment,
More informationECHOES FROM THE BAT CAVE
ECHOES FROM THE BAT CAVE Pen Turning Demo - Tom Szarek / Louis Harris Our very own Tom Szarek and Louis Harris demonstrated pen turning for the February meeting. Tom and Louis are coordinating a club service
More informationHERTS & BEDS WOODTURNERS WOODBITS
June 2017 Issue 133 All Day Demo 29 ober at Northall Village Hall. Demonstrator will be Richard Findley. 2017 Competition Subjects June July Aug Sept Nov Dec A lidded box A bowl Decorated item Kitchen
More informationWoodchips OCTOBER. November Challenge Anything you ve done using Cole jaws, reverse turning, or vacuum chuck THE CHALLENGE SHOW AND TELL
Woodchips - 2014 OCTOBER Remember! Get your raffle tickets when you come into the meeting November Challenge Anything you ve done using Cole jaws, reverse turning, or vacuum chuck November Demo Spindle
More informationKris Coyan s Steps to Make a 2-Piece Inside-Out Ornament: 1) Find (2) pieces of wood that have at least two parallel surfaces (such as pen blanks
The October demo was provided by Kris Coyan. Kris showed us how to create very nice but simple tree ornaments using the 2-piece inside-out method. The photo at left are examples of this type of ornament.
More informationWoodworker s Journal sent four identical blocks of butternut, 6" x 4" x 12", to four turners of varying degrees of expertise.
By Steve Blenk here do turners get their ideas? How do they put them into practice? Conversations about what inspires those whose woodworking focuses on woodturning tend to either begin or end with one
More informationECHOES FROM THE BAT CAVE
ECHOES FROM THE BAT CAVE January 2019 Tom Huber - Ornament Turning Tom Huber of the Capital Area Woodworkers (CAW) was our demonstrator for January. Tom showed us how to turn lighthouse and snowman ornaments.
More informationCentral Coast Woodturners Of California
Central Coast Woodturners Of California CCW a chapter of American Assoc. of Woodturners Bill Kandler President 805 489 5309 Gordon Rowland Vice President 805 929 4101 Terry Cohen Treasurer 805 747 4584
More informationOne Good Turn. Coulee Region WoodTurners. Chapter of the American Association of WoodTurners.
One Good Turn Coulee Region Woodturners Chapter of the American Association of WoodTurners Www.crwoodturner.com Happy New Year Everyone! Thank you to our past officers, and welcome to new officers who
More informationNorth Alabama Woodturners Newsletter A registered AAW chapter Edition 18-09
North Alabama Woodturners Newsletter A registered AAW chapter Edition 18-09 2 Meeting Dates: NAW meets the 4th Saturday of each month except when the meeting conflicts with a holiday or major wood turning
More informationMinutes/Newsletter of Space Coast Woodturners June 14, 2017
Minutes/Newsletter of Space Coast Woodturners June 14, 2017 Submitted by Randy Hardy from notes taken by Dotty Pugh (Thanks Dotty!) Just a reminder the meetings are held on the second Wednesday of the
More informationCLUB CALENDAR Our next general meeting will be March 8th, 2014 at BOCES at 9:00 am.
JANUARY 22, 2014 VOLUME 25, NUMBER 1 CLUB CALENDAR Our next general meeting will be March 8th, 2014 at BOCES at 9:00 am. CLUB MEETINGS Long Island Wood turners Association, Inc. is a member of the American
More informationJuly 19. Newsletter of the Treasure Coast Woodturning Guild June In this issue:
1 Treasure Coast Woodturners 7/10/2013 An Affiliate Chapter of the American Association of Woodturners In this issue: Newsletter of the Treasure Coast Woodturning Guild June 2013 Letter from the President
More informationCape Cod Woodturners Minutes and News October 7, 2015
Cape Cod Woodturners Minutes and News October 7, 2015 Vice president Jim Silva welcomed 23 members and guests to the meeting. End grain sealer, sandpaper, and CA glue is available from the club for purchase.
More informationBetween Centers Club established
Newsletter of Ozark Woodturners Between Centers Club established 1995 http://www.ozarkwoodturners.com 2015 Officers President: Joe Parks 870-307-8842 Vice President: Jerry Hankins 479-857-3980 Treasurer:
More informationEchoes from the BAT. Inside this month s BAT Cave. Details inside. Bill Henry Kicks off October Meeting. November 50/50 Raffle One Lucky Winner
Echoes from the BAT November 11, 2009 Volume 4, Issue 11 Inside this month s BAT Cave Bill Henry Kicks off October Meeting 2009 Officers President Bill Henry Vice President Keith Holt November 50/50 Raffle
More informationTHE SKEWED VIEW BI-CITY WOODTURNERS NEWSLETTER. Acorn Bird Houses for Everyone!! It s Christmas time again... (Just the cutest little houses)
Volume 5, Issue 12 December 2008 BI-CITY WOODTURNERS NEWSLETTER Acorn Bird Houses for Everyone!! It s Christmas time again... (Just the cutest little houses) Leroy Paul was our Dec. Demonstrator: See Page
More informationImage Item Model Price. Salt mill Mechanism Kit NO ROD INCLUDED (USA) Woodturning Kit Chrome Bottle Opener Kit (Woodturning) 07045
PO Box 531 Merrimack, NH 03054 craig@chefwarekits.com 267 888 6216 http://www.chefwarekits.com/ Category: All Categories Image Item Model Price Salt mill Mechanism Kit NO ROD INCLUDED (USA) Woodturning
More informationDid you remember the project of the month? Treasurer: Ken Lawson
Professor Paul has done it again! If you were late for class or snoozing, You missed a good session. Leroy s morning demo on Icicles and Finials was on point. He makes it look so effortless. It is easy
More informationMinutes/Newsletter of Space Coast Woodturners March 8, 2017
Minutes/Newsletter of Space Coast Woodturners March 8, 2017 Submitted by Randy Hardy Secretary Just a reminder the meetings are held on the second Wednesday of the month from 7:00 9:00 PM and the handson
More informationMinutes of the May 13, 2014 meeting of the Gateway Turners Next Hands On June 7, from 12 noon until 3:00 pm
xx President: Ian H Manley... ihmserv@comcast.net Vice President: Jim Silva jim@basketryetc.com Treasurer: Phil Arcouette Sr.. philbyarc47@verizon.net Secretary: Lenny Langevin..lennysminiatures@gmail.com
More informationBenoit Averly Demo # Eli Avisera Demo #1 Demo #2 Demo #3 Demo #4 Demo #5 Demo #6 Richard Findley Demo 1 Demo 2 Demo Demo
Benoit Averly Demo #1 Little Boxes with a French Accent How to turn little boxes using the skew a the main tool. Demo #2 Hut and Flat Boxes Turning larger hut and flat boxes. This is the next step. The
More informationNational Certificate in Woodturning
National Certificate in Woodturning The National Association of Woodworkers offers the Certificate in Woodturning as a high quality, nation-wide, woodturner training programme. This programme was developed
More informationNorthern Rockies Woodworking Guild
Northern Rockies Woodworking Guild March 31, 2018 NRWG.org Volume 13, Issue 7 Officers President Jurgen Weiel Vice President Jarred McDaniel Treasurer Boyd Carson Secretary Dean Center Next Meeting Tuesday,
More informationArtistic Woodturners Meeting of 12 August 2017
Artistic Woodturners Meeting of 12 August 2017 Meeting was called to order by Norm Freeman. One visitor, Mike Francis, president of Azalea Woodturners, was recognized. 25 members attended. Business portion
More informationChips & Bits. Peace River Woodturners. Meeting Annncements. Frank Bauer s Spin Top turning demonstration
Chips & Bits Peace River Woodturners Volume 8 Issue 10 A chapter of the American Association of Woodturners October 2015 President: Contact Us Norman Desjardins: 941-613-0245 Vice President: Bob Moran:
More informationBetween Turns. Sharpening..In s & Outs. New Mentoring Update. Michigan Association of Woodturers A chapter of the American Association of Woodturners
C O N T A C T U S President: Tom Mogford 810-629-6176 Vice President: Pete Buccelato Between Turns Michigan Association of Woodturers A chapter of the American Association of Woodturners V O L U M E 2
More informationGBWG Newsletter. March. March Meeting. Peter Fabricious Demo of EZ Threading Jig and Sphere Cutting Tool. Executive Members.
March Meeting The club has been notified that we can continue to use the firehall for our meetings and other activities. Volunteers are being sought for the Southampton Art School classes this summer,
More informationBetween Turns. April 2012 MAW Meeting. Upcoming Dates. Michigan Association of Woodturners A chapter of the American Association of Woodturners
Between Turns C O N T A C T U S : President: Tom Mogford 810-629-6176 Vice President: Michigan Association of Woodturners A chapter of the American Association of Woodturners V O L U M E 2 4, I S S U E
More informationPeace River Woodturners
Peace River Woodturners Volume 8 Issue 9 A chapter of the American Association of Woodturners September 2015 Norm s Sample bowl for his demonstration. In This Issue Norm explaining his demonstration of
More informationChristmas Bell Ornament
Christmas Bell Ornament This is an easy Christmas ornament idea I cabbaged from a friend and skilled turner, Curt Fuller, from Utah. I kind of adapted it to my style but I still got the idea from him.
More informationHERTS & BEDS WOODTURNERS WOODBITS
March 2018 Issue 142 2018 Competition Subjects Mar April May June July Aug Sept Oct Nov Dec 2 or more woods Decorated Easter egg Hollow form Platter Mallet Egg & Cup Round bottomed bowl Ball Candle holder
More informationOne Good Turn. Coulee Region Woodturners. Chapter of the American Association of WoodTurners.
One Good Turn Coulee Region Woodturners Chapter of the American Association of WoodTurners Www.crwoodturner.com A big thank you to Clyde Cassell for hosting our meeting in August. What a wonderful location
More informationNewsletter. South Central PA Woodturners. Officers President - Bill Fordney September/October 2009
South Central PA Woodturners Newsletter September/October 2009 Officers President - Bill Fordney 717 741-0957 NEROTOO@comcast.net Treasurer John Stewart 717 755-8737 JRWS3088@aol.com Secretary Mike Galloway
More informationBetween Centers Club established
Newsletter of Ozark Woodturners Between Centers Club established 1995 http://www.ozarkwoodturners.com 2016 Club Officers President: Ron Ufkes 870-507-0007 Vice Pres.: Kenneth Higgins 870-405-7283 Treasurer:
More informationVolume 13, Issue 11: November 2015
PBCW News Volume 13, Issue 11: November 2015 Next Meeting: November 14, 2015 Inside This Issue: October Demonstration PBCW WITVA Awards October 24 Minutes Collaboration Gallery Tools, Tips, Techniques
More informationVolume 9, Number 6 January 2018
www.gfturners.org Volume 9, Number 6 January 2018 A Few Word s. I want to thank the following members who stepped up to provide demos during the year: Dirk Johnson Four Times Sam Sampedro Three Times Chuck
More informationMalcolm Zander malcolmzander.com Ottawa, Ontario Canada
Malcolm Zander mzander@magma.ca malcolmzander.com 613-226-5041 Ottawa, Ontario Canada I began turning in 2000. Obviously I have a lace fetish. This I blame on Binh Pho, whose seminar in Albany I attended
More informationMaking Boxes with Threaded Lids Using a Threading Jig
My Way of Making Boxes with Threaded Lids Using a Threading Jig Smoky Mountains Woodturners March 18, 2014 Jared Bruckner Introduction Included in this Demo My procedure for preparing box blanks from wet
More informationWOODTURNERS. Providing Woodturning Education, Assistance and Experience to the Miami-Dade Community
2013 September Newsletter Vol. 26 Number 9 Workshop 8 Instant Gallery 8 Bring Back WWW.SFWTG.COM South Florida A Chapter of the American Association of Woodturners WOODTURNERS Guild Providing Woodturning
More informationSeptember Turn and Tell
Alabama Woodturners Association A member of the American Association of Woodturners Location-Homewood Senior Center; 816 Oak Grove Road; Homewood, Alabama 35209 www.alabamawoodturners.com Coming Events
More informationBuckeye Woodworkers and Woodturners
Buckeye Woodworkers and Woodturners The Official Newsletter of the Buckeye Woodworkers and Woodturners Your Officers President Fred Totts 330-325-7517 Vice President Bruce Lance 330-633-9622 Secretary
More informationThe finished ornaments.
Introduction I like to make different Christmas Ornaments every year to give to my relatives. This article describes the rnaments that I m making this year. The ornaments use a split turning of either
More informationThe Turning Point. In This Issue. March Meeting
The Turning Point The newsletter of the Siouxland Woodturners A Chapter of the American Association of Woodturners February 2016 In This Issue March Meeting.... Page 1 From the President... Page 1 February
More informationFig2: The Sliding Glue Block from the back.
Ornament Stand Introduction It was one of those forehead smacking moments. I was taking the #2 jaws off my Stronghold chuck, to put on my homemade wooden two jaw chuck set-up. For some reason instead of
More informationHARRY NOHR WOODTURNERS
HARRY NOHR WOODTURNERS Platteville, Wisconsin Newsletter Volume 7, Issue 7 July 2015 Harry Nohr Woodturners 2015 Officers President-Lyndal Anthony 563.599.8042 Vice President-Roger Redington Secretary-John
More informationA Publication of the Mid Minnesota Association of Woodturners
A Publication of the Mid Minnesota Association of Woodturners Volume 8, Issue 8 August 1, 2018 The Mid Minnesota Association of Woodturners (MMAW) is a member based not for profit organization, providing
More informationINLAND NORTHWEST WOODTURNERS NEWSLETTER. May Meeting 2008
INLAND NORTHWEST WOODTURNERS NEWSLETTER Next Meeting is Thursday, June 5, 2008 at WoodCraft Store classroom, N.E. corner of Sprague and Sullivan (N. side of the Fred Meyer parking lot) 7:00 PM May Meeting
More informationPresident s Message By Bob Clark Bill Clark and Friends Dick McCoy working Spindles
July 2010 Newsletter Volume 10 Issue 3 Newsletter of the Antelope Valley Woodturners Association 2535 E. Ave. R-3, Palmdale, CA. 93550 Member of the American Association of Woodturners President Bob Clark
More informationAlabama Woodturners Association
Alabama Woodturners Association A member of the American Association of Woodturners Location-Homewood Senior Center; 816 Oak Grove Road; Homewood, Alabama 35209 www.alabamawoodturners.com November 2016
More informationTurning Threads In Wood -- It's Easier Than You Think
Turning Threads In Wood -- It's Easier Than You Think David Gould I first became interested in thread chasing while watching the Mike Mahoney video Hollow Forms And Urns A Workshop, in which Mike threaded
More informationChristmas Party. December The monthly newsletter of the Inland Woodturners
A Member of the American Association of Woodturners December 2013 Christmas Party 1 Officers 2 Monthly Challenge, Wood Raffle, 2 Instant Gallery 3 Woodturning Schools 4 Upcoming Events 5 Festivities 6
More informationTHE WOODTURNER. January John Holderman. Skew Demo
Golden Triangle Woodturners Club Denton Texas January 2015 John Holderman Skew Demo My father worked in a lumber yard and always helped friends build their houses, fix barns and any odd job that dealt
More informationEchos From the BAT Cave
Echos From the BAT Cave Baltimore Area Turners June, 204 Inside this issue: Ironman and Show and Tell Ironman Challenge Show and Tell Other Stuff BAT members filled the tables with items to Show and Tell
More informationRichmond Woodturners Newsletter
Next Meeting: @Woodcraft, old Circuit City Plaza, 9862 West Broad St (Rt. 250W), Richmond, on the third Thursday of every month, 6:30PM. Refreshments provided. September 17 Editor: Betsy Mack bcmack@comcast.net
More informationBetween Centers Club established
Newsletter of Ozark Woodturners Between Centers Club established 1995 http://www.ozarkwoodturners.com 2016 Club Officers President: Ron Ufkes 870-507-0007 Vice Pres.: Kenneth Higgins 870-405-7283 Treasurer:
More informationNews And Views for February And March 2019
News And Views for February And March 2019 Hail Hail the gang is almost here, by rough count we had a high number of attendees at the February meeting, 48 to be exact. Well done, it gave for great participation,
More informationVolume 8, Number 9 June 2017
www.gfturners.org Volume 8, Number 9 June 2017 He emphasized the used of the diamond pattern used to design the colors of the star segments. In the great handout he provided, the last page, which can be
More informationthe 360 Volume 25 Issue 1 January 2017 WCWT Christmas Party 2016
Volume 25 Issue 1 January 2017 All the News That Will Fit On the Lathe the 360 A Message From Mark Hubl, Your President Well what a party! Where s my hat? Has anyone seen my hat but seriously I hope that
More informationDecember Mark Palma with his sculpture for the President s Challenge. Other Scupltures are seen in the background.
December 2015 Mark Palma with his sculpture for the President s Challenge. Other Scupltures are seen in the background. IN THIS ISSUE PREZ SEZ Page 2 President s Challenge Page 12 Coming Events Page 2
More informationApple Valley Woodturners
Apple Valley Woodturners May 2013 Officers President: Rich Vossler rvossler@gbp.com 540-327- 6455 Vice President: Scott Schlosser huntlybears@comcast.net 540-533-2007 Secretary: Mark Zimmerman mbzimmerman@comc
More informationFebruary 2018 Newsletter
February 2018 Newsletter visit us at www. taywood.org Help! We are desperately needing a Newsletter editor. With nobody to fill the shoes of Dave Inglis who is now our secretary, the monthly Newsletter
More informationMay Meeting 1 President s Corner 1 Minutes 2 From the Editor 3
THE NEXT MEETING June 25 AT THE TABLE TENNIS CLUB 1407 E HARRY VOLUME 16 ISSUE 6 Social Gathering @ 6:30 PM Meeting Starts @ 7:00 PM Subject Page May Meeting 1 President s Corner 1 Minutes 2 From the Editor
More informationA Member of the American Association of Woodturners
A Member of the American Association of Woodturners April 2016 The monthly newsletter of the Inland Woodturners Square Bowl 1 Officers 2 Candle Stick Holder Written by Larry Cooper Photos by Larry Cooper
More informationNorth Texas Woodworkers Association
Welcome President John Loftis welcomed a large group to the May meeting. Steve Yauch said he will be sending out information on the annual tool sale in Garland. John Loftis says he has a 37 Performex drum
More information*****Note***** Contains January 2018 Minutes February, Buckeye Woodworkers & Woodturners Newsletter February 2018
Contains January 2018 Minutes February, 2018 NO MEMBERS OR VISITORS SHALL ENTER OR EXIT THE CAMP VIA THE CHRISTMAN ROAD EN- TRANCE. MEMBERS MUST ENTER AND EXIT FROM MT.PLEASANT ROAD. BUCKEYE WOODWORKERS
More informationSouth Central Pennsylvania Wood Turners Club
South Central Pennsylvania Wood Turners Club 18 Water Street, Jacobus, PA 17407 President Bill Krofft wkrofft@hotmail.com (724) 504-5565 Vice-President Tom Deneen Tomdeneen@emailaccount.com (717) 927-9004
More informationJune Greatest auction in years, where were you?
June 2006 Greatest auction in years, where were you? By David Floyd & Jerry Schaible By all accounts the annual BWWT Auction was a great success. The final figures were not yet available, but best estimates
More informationRichmond Woodturners Newsletter
Ay Ma Richmond Woodturners Newsletter Next Meeting: @Woodcraft, 9862 West Broad St (Rt. 250W& Gaskin)), Glen Allen, on the third Thursday of every month, 6:30PM. Refreshments provided. Donations are welcome.
More informationMeeting Announcement: Date: June 8, 2000 Time: 6:30 9:30 PM Place: Woodcraft Supply 6123 Backlick Rd.. Springfield, VA 22150
S June 2000 The CAW Newsletter http://www.capwoodturners.org. The CAW Newsletter is the official publication of the Capital Area Woodturners Chapter of the AAW, and is published for the information of
More information