FEATHER LODGE BASE CABINET ASSEMBLY GUIDE
|
|
- Nathaniel Holt
- 5 years ago
- Views:
Transcription
1 FETHER LODGE SE CINET SSEMLY GUIDE WELCOME TO FETHER LODGE CINETS Thank you for purchasng Feather Lodge cabnets. You are on your way to a beautful, new ktchen, vanty, or closet. There are a few smple tools necessary, and some set up of your preparaton area before you get started. Our cabnets go together easly, but you may want to ask a frend for assstance when puttng together larger cabnets. One of you can algn the components whle the other screws them together. Once you get gong, assembly gets easer as you mprove your learnng curve! Expect t to take between mnutes per cabnet. y assemblng your own cabnets, you are savng the thousands that companes charge for sem-custom cabnetry. STEP 1 PREPRE CINETS FOR SSEMLY Equpment: Phllps Head screw drver, flat head screw drver, cordless electrc drll wth the flat and phllps attachment bts (not necessary, but s a tme saver). and rubber mallet. Prep rea: drt free carpet or the foam sheets and cardboard from your cabnet wll provde you wth a scratch free cushoned work area. To save your back, workng at table heght s always a good dea. Unpack your cabnet components and spread out the panels on your smooth prep surface. Keep tools and the package of hardware screws, brackets, etc close by, but not under any of the panels. Feather Lodge shps your cabnets wth the hnges alread secured to the doorframe faces, makng nstallaton qucker. We predrll all holes for easy acceptance of our hardware. ll hardware, mountng brackets, shelves, drawer pulls and screws(plus extra) are provded. Hardware s packaged separate from the cabnet panels so there s no damage. Dovetaled drawers can be tapped together wth a rubber mallet. PGE
2 STEP 2 WHICH CLIP SYSTEM DO YOU HVE? 2 PIECE CLIP SYSTEM PLSTIC CM LOCK x x Slde clp down nto place and fasten wth phllps head screw ncluded n hardware Seat female cam nto place on top of male cam. Turn cam screw 180 degrees clockwse wth flat head screwdrver to lock n place P x x X PGE 2
3 STEP 3 TTCH S TO FRONT Place front of cabnet face down onto padded work surface. Lne up fasteners on the sde of the cabnet to the front of the cabnets. Lock fasteners n place. Repeat wth other sde of cabnet. FRONT FSTENER FRONT FSTENER PGE 3
4 STEP 4 SLIDE IN CINET FLOOR PNEL Identfy the cabnet floor panel. It s easy to dentfy because t s only fnshed on one sde. Make sure that the fnshed sde s facng the nsde of the cabnet. Slde the cabnet floor panel nto the dado jont (the shallow groove runnng along both sdes of the cabnet, close to the bottom). UNFINISHED PORTION FCES OUT CINET FLOOR PNEL PNEL FINISHED PORTION IS FCING IN DDO CINET FLOOR PNEL STEP 5 LOCK IN CK PNEL Identfy the cabnet back panel. It s easy to dentfy because t s only fnshed on one sde. Make sure that the fnshed sde s facng the nsde of the cabnet. Lne the back of the cabnet up wth the fasteners on the sdes of the cabnet, settng fasteners n place. Lock the back to the sdes usng the fasteners. UNFINISHED PORTION FCES OUT PGE 4
5 STEP 6 TOE KICK INSTLLTION Slde the toe kck nto place onto fasteners. Lock fasteners to the toe kck. CK PNEL TOE KICK STEP 7 INSTLLING SHELVING Slde clear acrylc clps nto predrlled holes along sdewalls of shelves at heght that works best for you. For a level shelf, count up the holes from the bottom before nstallng clps. SHELF CRYLIC SHELF CLIPS INNER WLL OF CINET PGE 5
6 STEP 8 SOFT CLOSE DRWER GLIDES In the back of the cabnet, at the level of the drawer, you wll fnd predrlled holes. Identfy the plastc L shaped soft close mechansm from the bag of enclosed parts. Place L shaped soft close mechansm nto predrlled holes. Optonal but not necessary-screw nto place wth provded screws. STEP 9 DRWER GLIDE INSTLLTION Take metal drawer glde and slde t nto the plastc L shaped bracket you prevously attached to the back of the cabnet. Lne the front of the glde so t s flush wth the front of the frame, and lned up wth the predrlled holes. Screw n place wth the small 7/16 flat head screws. Repeat on other sde of cabnet. X PGE 6
7 STEP 10 PUT TOGETHER DRWERS You ll fnd fve peces that make up the drawers. ll of our cabnets have dovetaled jonts. Just lne up the holes and screw together. Lne up the parts, then hang front edge over an elevated work surface. Gently tap jonts together wth a rubber mallet. DRWER DRWER CK DRWER IN SE DRWER FRONT DRWER Fnd the orange and blue clps n the accessores bag. Lne them up toward front of drawer as shown. Use the stanless screws packaged wth clps to fasten them to the botom front of the drawer. PGE 7
8 STEP 11 INSTLL DRWER TO CINET OX Take assembled drawer and lne t on top of the metal gldes. Push the back of the metal glde nto the predrlled hole located at the back of the drawer untl t s flush wth the back porton of cabnet. The mechansm wll come together wth a few clcks. UNDER OF DRWER UNDER OF DRWER PGE 8
9 STEP 12 RCING Screw n vnyl corner braces and you are done! Use the eght round-head 1/2 screws to fasten the brace to the cabnet. X X OVERHED VIEW FRONT CONGRTULTIONS, YOU RE DONE! PGE 9
Base Cabinet. Assembly Guide. Give Us A Call at ext 2. Or You Can Watch The Assembly Videos Here
Base Cabinet Assembly Guide 1 Hey there! Assembling our cabinets is really simple, but in case you re a little nervous, this guide should help. Simply follow this quick guide and you ll be a cabinet assembly
More informationWall Cabinet Assembly Guide
Wall Cabinet Assembly Guide 1 Hey there! Assembling our cabinets is really simple, but in case you re a little nervous, this guide should help. Simply follow this quick guide and you ll be a cabinet assembly
More informationNEXUS SERIES CABINETS
NEXUS SERIES CABINETS STANDARD BASE ASSEMBLY INSTRUCTIONS Also applies to: Galaxy Series, Nexus Series, Ridgeline Series, Statesman Series, and Waterford Series FOR YOUR INFORMATION: These assembly instructions
More informationCABINETRY Assembly Instructions
www.hdicabinetry.com Assembly Instructions TABLE OF CONTENTS Category Page(s) Section 1: Framed Series Base Cabinet Instructions Wall Cabinet Instructions Easy Reach Cabinet Instructions 1.01-1.04 1.05-1.06
More informationC O N C E A L E D F I X I N G. PH:
C O N C E A L E D I X I N G D I Y S l a t Systems PH: 1300 336 237 Alumnum Concealed xng Slat Systems Our Concealed xng Alumnum Slat range offers the latest n archtectural style combned wth a unque nstall
More informationAssembly Instructions
Selling Station Assembly Instructions View from above without top A B C D Rounded finished corners on A & D Square unfinished 3-sides on B & C Selling Station Components (2) 2' x 6' Side s Have a channel
More informationFor assembly see instructions in carton
88 5523 943 Kitchen Island IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occurring to the parts. We have
More informationPantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or oth
88 5076 691 Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occurring to the parts. We have taken great
More informationCommercial Wine & Liquor Display. Double Displays
Commercial Wine & Liquor Display Double Displays Congratulations! You have purchased a superior commercial wine rack kit. These commercial kits have been specifically designed to properly store and display
More informationAbsco Space Saver Shed Assembly Instructions Model: J30082S
Assembly Instructons FRONT BASE LENGTH: 9ft-0-7 64n SIDE BASE LENGTH: ft-6-45 64n FRONT WALL HEIGHT: 5ft-0-55 64n REAR WALL HEIGHT: 6ft-4-49 64n ft-0-4 64n CONCRETE SLAB 0ft--3 64n CONCRETE SLAB WHEN LAYING
More informationHampshire Buffet Cabinet with Glass Doors
Thanks for shopping with Improvements! Hampshire Buffet Cabinet with Glass Doors Item #55919 Note: Read these instructions carefully before assembling. Tools required: Philips screwdriver (not included).
More informationPRO-CRIMPER* III Hand Crimping Tool Assembly and Die Assemblies [ ]
PRO-CRIMPER* III Hand Crmpng Tool Assembly 58546-1 and De Assembles 58545-[ ] Instructon Sheet 408-8678 13 MAR 14 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually
More informationWOOD GRAIN 6 SHELF BOOKCASE
HRDWRE 4 - wood dowels 20 - cam 8 - large 12 - shelf pins 4 - adhesive cam covers 20 - cams 8 - brackets Missing hardware? Please call 800.606.6387 for replacements. WLL MOUNTING HRDWRE 2 - small 2 - large
More informationHow to Get Started with Virtual Goalie
How to Get Started wth Vrtual Goale HTC VIVE Set up your computer and moble devce Acqure a vrtual realty-enabled computer and the HTC Vve. For hardware specs, to test your computer, or to order from Amazon,
More informationVigilant Cigar Humidor Vault. Assembly Instructions
Vigilant Cigar Humidor Vault Assembly Instructions Models: 1000, 1500, and 2000 Congratulations! You have purchased a superior cigar humidor. These humidors have been specifically designed to properly
More informationMS555200TX Porter Gaming/Media Console Espresso Finish Assembly Instructions
MS55500TX Porter Gaming/Media Console Espresso Finish Assembly Instructions For assistance with assembly, contact: Southern Enterprises Inc. Customer Service 1-800-6-5096 service@seidal.com www.seidal.com
More informationThanks for shopping with Improvements! Laundry Folding Table with 3 Clothes Hampers Item #
-- Thanks for shopping with Improvements! Laundry Folding Table with 3 Clothes Hampers Item # 568376 Note: Read these instructions carefully before assembling. Tools required: Philips screwdriver (not
More informationAbsco Workshop Shed Model: 45302WK
Absco Workshop Shed Model: FRONT: 4.48m SIDE: 3.0m HEIGHT: 2.m CONCRETE SLAB 300mm 4580mm CONCRETE WHEN LAYING YOUR CONCRETE SLAB, ENSURE THERE IS A REBATED EDGE 25mm DEEP AROUND THE PERIMETER 00mm REBATED
More informationThanks for shopping with Improvements! Rolling Kitchen Storage Cart with Wood Top Item #583649
Thanks for shopping with Improvements! Rolling Kitchen Storage Cart with Wood Top Item #58349 Note: Read these instructions carefully before assembling. Tools required: Philips screwdriver (not included).
More informationTOOLS REQUIRED
VINTNER UFFET HRDWRE 16 - wood dowels 26 - back 16 - bolts 4 - pull bolts Thank you for purchasing the Vintner uffet. This page lists all the contents included in the box. Please take time to identify
More informationPIVOT BUFFET HARDWARE TOOLS REQUIRED COMPONENTS. 8 - cams 8 - cam screws bolts 44 - flat washers shelf pins.
PIVOT BUFFET HRDWRE 8 - cams 8 - cam screws 44 - bolts 44 - flat washers 44 - spring washers 8 - screws 16 - shelf pins Thank you for purchasing the Pivot Buffet. This page lists all the contents included
More informationColonial Classic Bar
88 5528 991 Colonial Classic Bar IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts.
More informationInstallation Instructions
by Plato Woodwork Installation Instructions Plato Woodwork, Inc. 200 Third Street SW P.O. Box 98 Plato, MN 55370 www.platowoodwork.com 800.328.5924 SECTION GUIDE GETTING STARTED PAGE # Installation Methods...
More informationSUMMIT HUTCH ASSEMBLY HARDWARE WALL MOUNTING HARDWARE TOOLS REQUIRED COMPONENTS. 4 - large. 4 - bolts 4 - flat 4 - spring small screws.
SSEMBLY HRDWRE Missing hardware? Please call 800.606.6387 for replacements. 20 - small 4 - large 4 - bolts 4 - flat 4 - spring washers washers 8 - shelf pins 4 - cam 4 - cams 2 - connecting brackets WLL
More informationRETRACTABLE SCREEN ASSEMBLY AND INSTALLATION INSTRUCTIONS. SINGLE OUTSWING (Retro) / (Full-Size) STEP 1: REVIEW & CHECK FIG.
STEP 1: REVIEW & CHECK ) CONFIRM DOOR HEIGHT & WIDTH You have purchased a SINGLE Retractable Screen for an INSWING door. HEIGHT: This unit is available in two sizes: Retro and Full-Size. Please make sure
More informationSteele TV Stand Stock # BH
LOT NUMBER: DATE PURCHASED: / / Steele TV Stand Stock # BH46-084-899-02 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store
More informationTIP FOR GETTING STARTED
Tip for getting started TIP FOR GETTING STARTED Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these
More informationCOACT MEDIA UNIT ASSEMBLY WITH X9 OPEN SHELF STORAGE OPTION PART # INSTALLATION INSTRUCTIONS
PART # 1609103 MEDIA UNIT ASSEMBLY WITH X9 OPEN SHELF STORAGE OPTION 1. Begin by placing the back panel on a flat non-marring surface, making sure the pre-drilled holes are facing up. Next, position the
More informationFREE CLIMBER 4400 ASSEMBLY INSTRUCTIONS 27694B
FREE CLIMBER 4400 ASSEMBLY INSTRUCTIONS 27694B 1 TOOLS REQUIRED: CLAW HAMMER KNIFE 1/2 WRENCH OR SOCKET 1. USE KNIFE TO REMOVE ALL PLASTIC STRAPS FROM AROUND PALLET AND CARTON. STRAP 2. USE CLAW HAMMER
More informationNordic - 2 Door 2 Drawer Tallboy
Nordc - oor rawer allboy ssembly Instructons - lease keep for future reference 66390 mensons Wdth : 8. cm epth : 49,0 cm Heght : 5,9 cm Important - lease read these nstructons fully before startng assembly
More informationBarnside Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratch
88 5516 653 Barnside Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have
More informationThanks for shopping with Improvements! Hamper Cabinet with Drawer Item #512188
Thanks for shopping with Improvements! Hamper Cabinet with Drawer Item #512188 IMPORTANT: Since the bin pivots forward, this unit must sit on the floor for safety reasons. Other items of the same width
More informationTITAN INDUSTRIAL RACK 6-FOOT TALL / 4-SHELF
TITAN INDUSTRIAL RACK 6-FOOT TALL / 4-SHELF DXST10000 IMPORTANT: Please read this manual carefully before assembling this storage rack and save it for reference INSTRUCTION MANUAL 3 TABLE OF CONTENTS
More informationThanks for shopping with Improvements! Slanted Shoe Shelves Item #512142
Thanks for shopping with Improvements! Slanted Shoe Shelves Item #512142 Note: Read these instructions carefully before assembling. Tools required: Philips screwdriver (not included). Find a clean, smooth
More informationThanks for shopping with Improvements! Dover Rolling Cart Item #583244
Thanks for shopping with Improvements! Dover Rolling Cart Item #58344 Note: Read these instructions carefully before assembling. Tools required: Philips screwdriver (not included). Find a clean, smooth
More informationNordic - 2 Door Wardrobe
Nordc - 2 oor Wardrobe ssembly Instructons - lease keep for future reference 62967 mensons Wdth : 8. cm epth : 49,0 cm Heght : 9, cm Important - lease read these nstructons fully before startng assembly
More informationBOOKCASE WARNING. Illustration 1
Illustration 1 Lower Back Panel Upper Back Panel Cam Connector Illustration 2 Left end Illustration 3 Cam Bolt Adjustable Shelf Left end Left End Panel Bottom/ Center Shelf Connector Cover Right End Panel
More informationJ. Base 1 pc. 1 pc. P. Shelf 2 pcs. Gate Leg. 1 pc. Head Cap Bolt 13 pcs. (+1 extra) Cam Lock Screw. Cam Lock. 20 pcs. (+1 extra)
88 5023 95C Kitchen Island with Breakfast Bar IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the
More informationFA968800TX Manchester Fireplace Console - Brown Mahogany Assembly Instructions
FA968800TX Manchester Fireplace Console - Brown Mahogany Assembly Instructions For assistance with assembly, contact: Southern Enterprises Inc. Customer Service 1-800-633-5096 service@seidal.com www.seidal.com
More informationItem # Thanks for shopping with Improvements!
Thanks for shopping with Improvements! Hampshire -Door Cabinet Item #5505 To order, call -800-64- West Chester, OH 45069 Made in China PR-6 If you have questions regarding this product, call -800-64- Mon.-Fri.
More informationVersion 1.0. Forbes Credenza File Cabinet.
Version 1.0 Forbes Credenza File Cabinet www.fantasticfurniture.com.au Enjoy Your purchase from Australia s Best Value Furniture Store www.fantasticfurniture.com.au PAGE 2 Assembly checklist Read through
More informationThanks for shopping with Improvements! Serena File Cart with Charging Station Item #513376
Thanks for shopping with Improvements! Serena File Cart with Charging Station Item #513376 Note: Read these instructions carefully before assembling. Tools required: Philips screwdriver (not included).
More informationVINTNER WINE TOWER HARDWARE TOOLS REQUIRED COMPONENTS cam covers cams 16 - cam screws. 1 - pull small screws.
HRDWRE 16 - cams 16 - cam s 16 - cam covers 1 - pull 1 - pull bolt 40 - wood dowels 28 - small s 8 - medium s Thank you for purchasing the Vintner Wine Tower. This page lists all the contents included
More informationMICROWAVE HOOD COMBINATION INSTALLATIONINSTRUCTIONS
MICROWVE HOOD COMINTION INSTLLTIONINSTRUCTIONS Ths product s sutable for use above electrc or gas cookng products up to 36" (91.4 cm) wde. These nstallaton nstructons cover dfferent models. The appearance
More information2E - 3E High Wind Kit Manual
Yag Dpole Vertcal (Patent# 6,677,914 E - 3E Hgh Wnd Kt Manual Antarctca at 7 mph SteppIR Antennas 11-116th Ave NE, Sute -, Bellevue, WA 984 Tel: 4-43-191 Fax: 4-46-441 Tech Support: 4-891-6134 www.steppr.com
More information(800) Dimensions (D x W x H): 24Ó x 48Ó x 60Ó
Dimensions (D x W x H): 24Ó x 48Ó x 60Ó (800) 637-9508 www.theshelvingstore.com Gorilla Rack Products is a division of Rapid Rack Industries, Inc. 14421 Bonelli Street City of Industry, CA 91746 At Gorilla
More informationWALL UNIT. Assembly Guide For Internal Use: FI.WR.INS.034_WKIN00124_WALL_ _1Dr_Rev4.indd
WLL UNIT ssembly uide 150 200 350 400 500 300 450 600 or Internal Use: I.WR.INS.034_WKIN00124_WLL_150-600_1Dr_Rev4.indd WLL UNIT ssembly uide EORE YOU STRT INSTLLTION SHOULD E PERORMED Y OMPETENT PERSON
More informationBase Cabinet w/drawers
Base Cabinet w/drawers WSBC-4C Dark Cherry finish WSBC-4W White finish ADULT ASSEMBLY REQUIRED DUE TO THE PRESENCE OF SMALL PARTS, SHARP POINTS, SHARP EDGES AS RECEIVED Pacific Standard Time: 8:30 a.m.
More informationAbsco Space Saver Shed Assembly Instructions Model: 23081SK
Assembly Instructons Model: 2308SK FRONT BASE LENGTH: 2.26m SIDE BASE LENGTH: 0.78m FRONT WALL HEIGHT:.80m REAR WALL HEIGHT:.95m CONCRETE SLAB 880mm 2360mm WHEN LAYING YOUR CONCRETE SLAB, CHAMFER THE 50mm
More informationWARM SHAKER / NORFOLK / LEXINGTON TV MEDIA STAND
SIMP II H O M E L I F E Y D E S I GN WARM SHAKER / NORFOLK / LEXINGTON TV MEDIA STAND 1/21 FOR REPLACEMENT PARTS OR HELP WITH ASSEMLY PLEASE CONTACT US AT: simpli-home.com/customer-support PLEASE ENSURE
More informationINSTALL INSTRUCTIONS WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES NEWAGE STEEL WELDED CABINETRY
NEWAGE STEEL WELDED CABINETRY WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES ALL CABINETS MUST BE MOUNTED TO STUDS ON A SECURE WALL, AS PER THESE INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN SERIOUS
More informationAssembly and Installation Guide
The Easy Hang Closet Solution SM Install Your elfa In An Instant. Enjoy The Benefits For A Lifetime. Basic Tools For elfa Assembly and Installation Level Hand or Power Drill Drill Bits 1/8", 3/8", 5/16"
More informationCanterbury 4 DRW CHEST
Canterbury 4 DRW CHEST Assembly Instructions - Please save for future reference 553/4801 565/2178 572/6080 25 kg 55 lbs 9 kg 20 lbs max. Dimensions Width - 84.3cm Depth - 41.9cm Height - 99.7cm Important
More informationTV/Media Stand- Mission Oak Finish. Assembly Instructions
TV/Media Stand- Mission Oak Finish Assembly Instructions TV/Media Stand Parts List Please review all parts and hardware before disposing of any packaging. Call Customer Service if missing hardware. Before
More informationHomestead Bar Cabinet IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent s
88 5527 991 Homestead Bar Cabinet IMPRTANT NTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts.
More informationOXYGEN INSTALLATION. Revision date
12345 1 Hardware List 12345 Flat head wood screw #9 x 7/8 long with #2 Phillips drive, silver Used to attach surfaces and end panels Hex set screw ½-13 x 2 long with 1/4 hex drive, black Used on Legs Hex
More informationMICROWAVEHOODCOMBINATION INSTALLATIONINSTRUCTIONS
MCROWVEHOODCOMNTON NSTLLTONNSTRUCTONS Ths product s sutable for use above electrc or gas cookng products up to and ncludng 36" (91.4 cm) wde. See "nstallaton Requrements" secton for further notes. These
More informationThanks for shopping with Improvements! Space-Saving Wall-Mount Drying Rack - Small Item #504668
Thanks for shopping with Improvements! Space-Saving Wall-Mount Drying Rack - Small Item #504668 Note: Read these instructions carefully before assembling. Tools required: Phillips screwdriver, flat screwdriver
More informationLeft Unit. G. Shelf 1 pc. Small Cam Lock 6 pcs.(+1 extra) Cam Lock Screw 2 pcs.(+1 extra) Cam Lock Screw 6 pcs.(+1 extra)
88 5180 181 Art & Craft Computer Desk (Cottage Oak) IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring
More informationMeredith Sinclair s DIY Clothespin Xmas Tree
1.Mer ed t hs nc l a r sdi YCl ot hes p nxma st r ee 2.DI YChr s t ma ss poons 3.DI YChr s t ma sca ndl ecent er p ec e Meredth Snclar s DIY Clothespn Xmas Tree Materals: Clothespns of varous szes, old
More informationCloset System Installation Manual
Closet System Manual Thank you For choosing our Custom Closet Collection to fit all your needs Closets come fully assembled to make your project an enjoyable and satisfying experience. With quality Custom
More informationCROWN IMPERIAL ASSEMBLY INSTRUCTIONS
CROWN IMPERIAL ASSEMBLY INSTRUCTIONS Standard Drawer Box Page 1 of 14 Standard Drawer Box Parts Parts Supplied B C D A E F G Page 2 of 14 Part Letter Part Name Quantity 300-600 Deep Pan A Base Panel 1
More informationP.O. Box 8400 Green Bay, WI (920)
P.O. Box 8400 Green Bay, WI 54308-8400 (920) 468-2165 Change Notice No. 112 Implemented By: KI-Pembroke Notification By: Scott Vissers Date: 03/15/10 Component Product Title: Series XXI Lateral Filing
More informationINSTALLATION GUIDE FTX FLOOR Ford Transit ( 148" Extended Wheelbase )
INSTALLATION GUIDE 6540-FTX FLOOR Ford Transit ( 148" Extended Wheelbase ) QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup... 3-4 Phase 2 - Installation q 2.1 Install Preparation... q 2.2 Floor Installation...
More informationINSTRUCTION BOOKLET #C0 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationDisplay-Top Apothecary Cabinet. Assembly Instructions. Page 1
Display-Top Apothecary Cabinet Assembly Instructions Page 1 Display-Top Apothecary Cabinet Parts List Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean,
More informationCOCKPIT CORNER UNIT WARNING. Illustration 1. Read all instructions and review illustrations before installing. Tools required for assembly:
Illustration 1 Illustration 2 Right side of Illustration 3 Right brace Right brace Read all instructions and review illustrations before installing. Tools required for assembly: Phillips screwdriver Rubber
More informationCloset Wall Drawer Unit
88 5531 751 Closet Wall Drawer Unit A. B. C. Shelf D. E. F. For assembly see instructions in carton 88 5531 752. 88 5531 752 Closet Wall Drawer Unit G. H. I. Plinth M. Bottom L. N. 2 pc. J. K. O. Drawer
More informationMira Premium Series Bi-Parting French Sliding Patio Door Installation Instructions
PREMIUM SERIES W I N D O W S Mira Premium Series Bi-Parting French Sliding Recommended Tools & Accessories Tape Measure Level (3 or longer) Hammer Power Screwdriver Load bearing Shims Flashing (recommended)
More informationD. Middle Panel. C. Middle Panel. 1 pc. B. Side Panel 1 pc. I. Back Stretcher. 1 pc. J. Front Stretcher. 1 pc. S. Door 1 pc. T.
itchen Cart IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the parts. We have taken great care
More informationSLOANE GREY/MAHOGANY LEANING WINE BAR
SLONE GREY/MHOGNY LENING WINE R SSEMLY HRDWRE 8 - wood dowels 10- small bolts 4 - large phillips bolts 4 - plates 1 - drawer sper 2 - large allen bolts MENDING HRDWRE 2 - connecting plates 4 - medium screws
More informationProduct must be installed as shown using the screws and brackets provided. Use of incorrect hardware could result in damage to the product.
General Notes These installation instructions are intended to be comprehensive for a typical Keyeira/Presto configuration. Your configuration may differ. If you have questions contact Geiger Customer Service
More informationM. Door 1 Pc. 1 Pc. Door 1 Pc. 1 Pc. M3x20 Wood Screw (long) 8 Pcs. (+1 extra) M3x10 Wood Screw for Magnet 8 Pcs. (+1 extra)
88 5516 653 Barnside Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have
More informationPlans. Easy-to-Build Full-size Deluxe Murphy Bed Plan. For more plans, tools and hardware visit rockler.com
Easy-to-Build Full-size Deluxe Murphy Bed Plan Build a full-size Deluxe Murphy Bed complete with decorative molding and matching side cabinets! Plans For more plans, tools and hardware visit rockler.com
More informationMount to the Wall INSTALLATION MANUAL
Mount to the Wall 15 Locate the Wooden Studs This step applies to wooden stud wall installation only. Determine and mark the exact locations of two stud centers on the wall. Wooden studs should be spaced
More informationPRO- CRIMPER* III Hand
PRO- CRIMPER* III Hand Instructon Sheet Crmpng Tool Assembly 58529-1 408-9999 wth De Assembly 58529-2 11 AUG 14 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually
More informationThanks for shopping with Improvements! Louvered Space Saver Cabinet Item #512059
Thanks for shopping with Improvements! Louvered Space Saver Cabinet Item #512059 Note: Read these instructions carefully before assembling. Tools required: Philips screwdriver (not included). Find a clean,
More informationPRO- CRIMPER* III Hand Crimping
PRO- CRIMPER* III Hand Crmpng Instructon Sheet Tool 58448-2 408-9357 Wth De 58448-3 10 Mar 11 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered hand
More informationReady-To-Assemble VersaRail INSTALLATION INSTRUCTIONS
FREEDOM-WEB Ready-To-Assemble VersaRail INSTALLATION INSTRUCTIONS Read all instructions prior to installing product. Refer to manufacturers safety instructions when operating any tools. To register your
More informationPRO-CRIMPER* III Hand Crimping Tool Assembly with Die AssemblY
PRO-CRIMPER* III Hand Crmpng Tool Assembly 90758-1 wth De AssemblY 90758-2 Instructon Sheet 408-9938 01 NOV 11 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually
More informationWALL UNIT. Assembly Guide Tall 1 Door. 200 Tall. 350 Tall. 150 Tall. 300 Tall. 400 Tall. 450 Tall. 500 Tall. 600 Tall
WLL UNIT ssembly uide 150 Tall 200 Tall 300 Tall 350 Tall 400 Tall 450 Tall 500 Tall 600 Tall or Internal Use: I.WR.INS.045_WKIN00130_WLL_150_600_Tall_1Dr_Rev3.indd WLL UNIT ssembly uide EORE YOU STRT
More informationSelect Lab Fixed Height Workstation
Assembly Instructions Select Lab Fixed Height Workstation Contents Important User Information.............................. 2 Safety Precautions.................................... 3 Required Tools........................................
More informationExtra Wide Designer Lockers Series Installation Instructions
Extra Wide Designer Lockers 20000 Series Thank you for selecting the 20000 Series Extra Wide Designer Lockers. We are confident that the quality and construction of the lockers will prove to be a good
More informationThanks for shopping with Improvements! Deluxe 10 Closet Organizer (12 deep) Item #461609
Thanks for shopping with Improvements! Deluxe 10 Closet Organizer (12 deep) Item #461609 To order, call 1-800-642-2112 West Chester, OH 45069 0114 If you have questions regarding this product, call 1-800-642-2112
More informationINSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationINSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationAssembly Instructions
Assembly Instructions Workbench Model: GR 1902 (Tan) Dimensions (D x W x H): 24 x 48 x 60 GR1902B (Black) For Instruction Assistance (800) 736-7225 WEEKDAYS: 8:00 a.m. - 5:00 p.m. Pacific Standard Time
More informationMonroe loveseat. assembly instructions
Monroe loveseat assembly instructions Smooth & Wrinkle-Free Fabric Covers: In addition to these printed instructions, you may want to watch our beauty tips videos on the customer service page of our website.
More information" BASE CABINET
INSTALLATION GUIDE INSTALLATION GUIDE Before You Begin Installing Your Kitchen Cabinets 1. Read through installation guide to understand all steps and gather tools needed. 2. Verify that all of the hardware,
More informationOxford Stalls Installation Instructions
Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or
More informationT-5 Floor Model SunLite Garden Assembly Instructions
T-5 Floor Model SunLite Garden Assembly Instructions The Floor Model Light Garden can be used alone or as a base for our popular Tabletop Light Garden (sold separately). Assembly takes less than an hour
More informationTOOLS REQUIRED: HARDWARE INCLUDED: 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS
1 TOOLS REQUIRED: RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RUBBER MALLET FOR INSERTING PANELS 8MM HEX BIT WITH EXTENSION FOR HEX BOLT
More informationCloset Wall Drawer Unit
IMPORTANT 88 5531 752 Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions
More informationroom essentials >> assembly instructions H 1 4 drawer chest DPCI # (Black Woodgrain) DPCI # (Espresso)
room essentials 4 drawer chest DPCI # 249-05 - 0103 (Black Woodgrain) DPCI # 249-05 - 0106 (Espresso) >> assembly instructions 92335 H 1 FREE! Do not go back to your store! we will help you! Missing or
More informationCDAS CDAS39 SHELF UNIT
BY CDAS CDAS39 SHELF UNIT 0708 IMPORTANT! Assembly may require the assistance of another person. Before you begin assembly: READ THE DIRECTIONS all the way through one time. This will speed up the process
More informationTOOLS REQUIRED FOR ASSEMBLY. Rubber Mallet or Plastic Tip Hammer PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER.
TOOLS REQUIRED FOR ASSEMBLY Rubber Mallet or Plastic Tip Hammer Top Cover Support PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER Back Stop Divider Closed 'L' Upright Slotted Reinforcement Support
More informationELEGANCE SHOWER DOOR/ENCLOSURE INSTALLATION INSTRUCTIONS. Style A Style B Style C Style D
ELEGANCE SHOWER DOOR/ENCLOSURE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationPRO- CRIMPER* III Hand Crimping
PRO- CRIMPER* III Hand Crmpng Instructon Sheet Tool Assembly 91338-1 408-8377 wth De Assembly 91338-2 22 JUL 09 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually
More informationSection 1. Kitchen installation. Base cabinets
Section 1 Kitchen installation Base cabinets Pre-build - Cabinet leg... page 16 Pre-build - Alternative cabinet leg... page 18 Pre-build - Cabinets.... page 19 Pre-build - Corner base cabinet centre upright
More informationCLARK 5-SHELF BOOKCASE
LRK 5-SHELF OOKSE MODEL N0. 06-70-2 SSEMLY INSTRUTIONS IMPORTNT: Please read and understand this manual before any assembly. efore beginning assembly of product, make sure all parts are present. ompare
More information