MICROWAVE HOOD COMBINATION INSTALLATIONINSTRUCTIONS

Transcription

1 MICROWVE HOOD COMINTION INSTLLTIONINSTRUCTIONS Ths product s sutable for use above electrc or gas cookng products up to 36" (91.4 cm) wde. These nstallaton nstructons cover dfferent models. The appearance of your partcular model may dffer slghtly from the llustraton n these nstallaton nstructons. Table of Contents MICROWVE HOOD COMINTION SFETY...1 INSTLLTIONREQUIREMENTS...2 Tools and Parts... 2 Locaton Requrements... 2 Product Dmensons... 3 Electrcal Requrements... 3 INSTLLTION INSTRUCTIONS...4 Remove Mountng Plate... 4 Rotate r Deflector... 4 Locate Wall Stud(s)... 6 Mark RearWall... 7 Drll Holes n RearWall...7 ttach Mountng Plate to Wall...8 Prepare Upper Cabnet... 8 Install the Mcrowave Oven...9 Complete Installaton...10 VENTING DESIGN SPECIFICTIONS...11 SSISTNCE Replacement Parts ccessores MICROWVE HOOD COMINTION SFETY Your safety and the safety of others are very mportant. We have provded many mportant safety messages n ths manual and on your applance. lways read and obey all safety messages. Ths s the safety alert symbol. Ths symbol alerts you to potental hazards that can kll or hurt you and others. ll safety messages wll follow the safety alert symbol and ether the word "DNGER" or "WRNING." These words mean: You can be klled or serously follow nstructons. njured f you don't mmedately You can be klled or serously njured f you don't follow nstructons. ll safety messages wll tell you what the potental hazard s, tell you how to reduce the chance of njury, and tell you what can happen f the nstructons are not followed

2 INSTLLTIONREQUIREMENTS Tools Needed Gather the requred tools and parts before startng nstallaton. Read and follow the nstructons provded wth any tools lsted here. Measurng tape Stud fnder Pencl 7/16" socket wrench (or box wrench) for 1/4" x 2" Maskng tape or thumbtacks lag screws Scssors 11/2'' (3.8 cm) dam. hole drll No. 2 Phllps screwdrver bt for wood or metal cabnet No. 3 Phllps screwdrver for 1/4-20 x 3" bolts Keyhole saw Electrc drll Caulkng gun and weatherproof caulkng 3/16" (5 mm), 3/8" (10 mm) compound drll bts Duct tape 3/4" (19 mm) hole saw Parts Suppled For reorder nformaton, see "Replacement Parts" secton. NOTE: The hardware tems lsted here are for wood studs. For other types of wall structures, be sure to use approprate fasteners. Check the openng where the mcrowave oven wll be nstalled. The locaton must provde: Mnmum nstallaton dmensons. See "Installaton Dmensons" llustraton. Mnmum one 2" x 4" (50.8 x mm) wood wall stud and mnmum 3/8" (9.5 mm) thckness drywall or plaster/lath wthn cabnet openng. Support for weght of 150 Ibs (68 kg), whch ncludes mcrowave oven and tems placed nsde the mcrowave oven and upper cabnet. Grounded electrcal outlet nsde upper cabnet. See "Electrcal Requrements" secton. NOTES: If nstallng the mcrowave oven near a left sdewall, make sure there s at least 6" (15.2 cm) of clearance between the wall and the mcrowave oven, so that the door can open fully. Some cabnet and buldng materals are not desgned to wthstand the heat produced by the mcrowave oven for cookng. Check wth your bulder or cabnet suppler to make sure that the materals used wll not dscolor, delamnate or sustan other damages. Specal Requrements For Wall Ventng Installaton Only: Cutout must be free of any obstructons so that the vent fts properly, and the damper blade opens freely and fully. For Roof Ventng Installaton Only: If you are usng a rectangular to round transton pece, the 3" (7.6 cm) clearance needs to exst above the mcrowave oven so that the damper blade can open freely and fully. See "Rectangular to Round Transton" llustraton n "Ventng Desgn Specfcatons" secton. 1. 1/4-20 x 3" bolts (4). Washers (2) C. Toggle nuts (2) D. 1/4" x 2" lag screws (2) E. Power supply cord bushng (1) F. Damper assembly (for wall or roof ventng) Not Shown: Upper cabnet template Mountng plate (attached to back of mcrowave oven) lumnum grease flters Charcoal flters (Dependng on model, charcoal flters may not be ncluded. See Use and Care Gude.) NOTE: Dependng on model, alumnum grease flter and charcoal flter may be combned. Materals needed Standard fttngs for wall or roof ventng. See "Ventng Desgn Specfcatons" secton. 2

3 Installaton Dmensons NOTE: The grounded 3 prong outlet must be nsde the upper cabnet. See "Electrcal Requrements" secton. Electrcal Shock Hazard 30" (76.2 crn) typcal* Plug nto a grounded 3 prong outlet. Do not remove ground prong. 66" (167.6 crn) rnn. Do not use an adapter. Do not use an extenson cord. Falure to follow these nstructons can result n death, fre, or electrcal shock. Observe all governng Requred: codes and ordnances. 120 Volt, 60 Hz, C only, 15- or 20-amp electrcal supply wth a fuse or crcut breaker. Recommended: tme-delay fuse or tme-delay crcut breaker. separate crcut servng only ths mcrowave oven.. 2" x 4" wall stud. Grounded 3 prong outlet *30" (76.2 cm) s typcal for 66" (167.6 cm) nstallaton heght. Exact dmensons may vary dependng on type of range/cooktop below. T 171/4" (43.8 1crn) GROUNDING NSTRUCTONS [] For all cord connected applances: The mcrowave oven must be grounded. In the event of an electrcal short crcut, groundng reduces the rsk of electrc shock by provdng an escape wre for the electrc current. The mcrowave oven s equpped wth a cord havng a groundng wre wth a groundng plug. The plug must be plugged nto an outlet that s properly nstalled and grounded. WRNING: Improper use of the groundng plug can result n a rsk of electrc shock. Consult a qualfed electrcan or servceman f the groundng nstructons are not completely understood, or f doubt exsts as to whether the mcrowave oven s properly grounded. Do not use an extenson cord. If the power supply cord s too short, have a qualfed electrcan or servceman nstall an outlet near the mcrowave oven. SVETHESEINSTRUCTIONS

4 INSTLLTIONINSTRUCTIONS._/ _,/._, _. %_ NOTE: To avod possble damage to the work surface, cover the work surface. 1. Remove any remanng contents from the mcrowave oven cavty. 2. Remove the mountng plate by peelng off the strps of tape that attach t to the back of the mcrowave oven, and set the mountng plate asde. \ The mcrowave oven s set for recrculaton nstallaton. For wall or roof ventng, changes must be made to the ventng system. NOTE: Skp ths secton f you are usng recrculaton nstallaton. Keep the damper assembly n case the ventng method s changed, or the mcrowave oven s renstalled n another locaton where wall or roof ventng may be used. Wall Ventng Installaton Only 1. Remove screws attachng damper plate to top of mcrowave oven exteror, then slde damper plate away from retanng tabs. \ o o _lo o o o o o o o o o o o o o o o o o o o!l v _ C. Mountng plate. ack of mcrowave oven C. Tape (multple locatons) o o o \j. Retanng tabs. Damper plate 2. Keep damper plate and screws together and set asde. 3. Slde ar deflector out of mcrowave oven. 3. Tape the mcrowave oven door closed so that door does not swng open whle the mcrowave oven s beng handled. NOTE: To avod damage to the mcrowave oven, do not grp or use the door or door handle whle the mcrowave oven s beng handled.. r deflector 4, Rotate ar deflector front to back so that deflector feet face the front of the mcrowave oven, and then slde ar deflector nto the back of the mcrowave oven as shown, makng sure ts exhaust port (open end) algns wth the mcrowave oven exhaust port.. Mcrowave oven exhaust port. Deflector feet C. r deflector exhaust port (open end)

5 5= Slde damper assembly nto the damper plate by placng the long tab of the assembly under the rased slot of the damper plate, as shown. /... \ C D Roof Ventng Installaton Only 1. Repeat Step 1 from "Wall Ventng Installaton Only." 2. Repeat Step 2 from "Wall Ventng Installaton Only." 3. Repeat Step 3 from "Wall Ventng Installaton Only." 4. Rotate ar deflector so that deflector feet face the bottom of the mcrowave oven, and then slde ar deflector nto the back of the mcrowave oven as shown, makng sure ts exhaust port (open end) algns wth the mcrowave oven exhaust port.. Damper assembly. Damper plate C. Long tab D. Rased slot 6= ttach the damper plate and assembly to the back of the mcrowave oven, as shown, and secure wth screws removed n Step 1. C D c. Mcrowave oven exhaust port. r deflector exhaust port (open end) C. Deflector feet 5= Slde damper later use. plate under the retanng tabs. Save screws for. ack of mcrowave oven. Damper plate C. Damper assembly D. Screws. Retanng tabs

6 NOTE: If no wall studs exst wthn the cabnet openng, do not 1. Usng a stud fnder, locate the edges of the wall stud(s) wthn nstall the mcrowave oven. the openng. See llustratons n "Possble Wall Stud Confguratons." 2. Mark the center of each stud, and draw a plumb lne down each stud center. See llustratons n "Possble Wall Stud Confguratons." Possble Wall Stud Confguratons These depctons show examples of preferred nstallaton confguratons wth the mountng plate. No Wall Studs at Corner Holes Fgure 1 No Wall Studs at Corner Holes Fgure 2 :,, C... :_ 1 1 ' C l/ // NOTE: If wall stud s wthn 6" (15.2 cm) of the vertcal centerlne (see "Mark Rear Wall" secton), only recrculaton or roof ventng nstallaton can be done. Wall Stud at One Corner Hole Fgure 3 Wall Studs at oth Corner Holes Fgure 4 g _ D F ' ;. Corner holes (on mountng plate). Cabnet openng vertcal centerlne C. Wall stud centerlnes D. Holes for lag screws E. Support tabs F. Mountng plate center markers 6

7 Wall Ventng Installaton Only The mcrowave oven must be nstalled on a mnmum of 1 wall stud, preferably 2, usng a mnmum of 1 lag screw, preferably Usng measurng tape, fnd and clearly mark the vertcal centerlne of the openng. Centerlne Upper cabnet bottom... }L_o_ I 4" (10.2cm) f %" (1 cm) I. Centerlne 6" (15.2 cm) 6" (15.2 cm) 2. Wth the support tabs facng forward (see llustratons n "Possble Wall Stud Confguratons" n "Locate Wall Stud(s)" secton), algn the mountng plate center markers to the centerlne on the wall, makng sure t s level, and that the top of the mountng plate s butted up aganst the bottom edge of the upper cabnet. NOTE: If the front edge of the upper cabnet s lower than the back edge, lower the mountng plate so that ts top s level wth the front edge of the cabnet Rear wall Holdng the mountng holes. C. Mountng plate C. Top of mountng plate must algn wth front edge of cabnel D. Front edge of upper cabnet J plate n place, mark both bottom corner Fnd the wall stud centerlne(s) marked n Step 2 of "Locate Wall Stud(s)," and mark at least 1, preferably 2, hole(s) through the mountng plate, closest to the centerlne(s). See fgures 1, 2 and/or 3 n "Possble Wall Stud Confguratons" n "Locate Wall Stud(s)" secton. The blackened holes n the shaded areas are deal hole locatons. 5. Set mountng plate asde. D Mark the centerlne 3/8" (1 cm) down from the bottom edge of the upper cabnet. Usng measurng tape, measure out 6" (15.2 cm) on both sdes of the centerlne, and mark. Measure down 4" (10.2 cm) from the mark made n Step 6, and mark. 9. Usng a straghtedge, draw the 2 horzontal, level lnes through the marks made n steps 6 and Draw the 2 vertcal, plumb lnes down from the marks made n Step 7 to complete the 12" x 4" (30.5 x 10.2 cm) rectangle. Ths s the ventng cutout area. 11. Cut a 3/4" (19 mm) hole n one corner of the cutout area. 12. Usng a keyhole saw, cut out the ventng cutout area. In addton to beng nstalled on at least 1 wall stud, the mountng plate must attach to the wall at both bottom corner holes. If the holes are not over wall studs, use two 1/4-20 x 3" round-head bolts wth toggle nuts; f 1 hole s over a wall stud, use 1 lag screw and one 1/4-20 x 3" round-head bolt wth toggle nut; or f both holes are over wall studs, use 2 lag screws. Followng are 3 nstallaton confguratons Installaton for No Wall Studs at Corner Holes (Fgures I & 2) Drll 3/4" (19 mm) holes through the wall at both bottom corner holes marked n Step 3 of "Mark Rear Wall." Drll 3/16" (5 mm) hole(s) nto the wall stud(s) at the hole(s) marked n Step 4 of "Mark Rear Wall." Refer to fgures 1 and 2 n "Possble Wall Stud Confguratons" n "Locate Wall Stud(s)" secton. Installaton for Wall Stud at One Corner Hole (Fgure 3) 1. Drll a 3/16" (5 mm) hole nto the wall stud at the corner hole marked n Step 3 of "Mark Rear Wall." 2. If nstallng on a second wall stud, drll a 3/16" (5 mm) hole nto the wall stud at the other hole marked n Step 4 of "Mark Rear Wall." Refer to Fgure 3 n "Possble Wall Stud Confguratons" n "Locate Wall Stud(s)" secton. 3. Drll a 3/4" (19 mm) hole through the wall at the other corner hole. Installaton for Wall Studs at oth Corner Holes (Fgure 4) 1. Drll 3/16" (5 mm) holes nto the studs at the corner holes marked n Step 3 of "Mark Rear Wall."

8 ,-_...o... _:,n o_ %_;_--4_ NOTE: Secure the mountng plate to the wall at both bottom corner holes drlled nto the wall studs and/or drywall usng ether 1/4-20 x 3" round-head bolts and toggle nuts or 1/4 x 2" lag screws. Refer to llustratons n "Possble Wall Stud Confguratons" n "Locate Wall Stud(s)" secton. No Wall Studs at Corner Holes (Fgures I & 2) NOTE: The mountng plate must be secured to the wall on at least 1 wall stud as well as at both bottom corners. 1. Wth the support tabs of the mountng plate facng forward, nsert 1/4-20 x 3" round-head bolts through both bottom corner holes of mountng plate. 2. Start toggle nuts on bolts from the back of the mountng plate. Leave enough space for the toggle nuts to go through the wall and open. Wall Stud at One Corner Hole (Fgure 3) 1. Wth the support tabs of the mountng plate facng forward, nsert a 1/4-20 x 3" round-head bolt through the corner hole that fts over the 3/4" (19 mm) hole drlled n Step 3 of "Installaton for One Wall Stud at One Corner Hole" n the "Drll Holes n Rear Wall" secton. 2. Start a toggle nut on the bolt from the back of the mountng plate. Leave enough space for the toggle nut to go through the wall and to open. 3. Poston mountng plate on the wall, makng sure that the top of the mountng plate s algned wth the front edge of the upper cabnet. 4. Push the bolt wth toggle nut through the drywall, and fnger tghten the bolt to make sure toggle nut has opened aganst drywall. 5. Insert a lag screw nto the remanng bottom corner hole. 6. If nstallng on a second wall stud, nsert a lag screw nto the other hole drlled n Step 2 of "Installaton for One Wall Stud at One Corner Hole" n the "Drll Holes n Rear Wall" secton. 7. Check algnment of mountng plate, makng sure t s level. 8. Securely tghten the lag screw(s) and bolt. Wall Studs at oth Corner Holes (Fgure 4). 1/4-20 x 3" round-head bolt. Mountng plate C. Sprng toggle nut 1. Poston mountng plate on the wall, makng sure that the top of the mountng plate s algned wth the front edge of the upper cabnet. 2. Insert lag screws nto both bottom corner holes. 3. Check algnment of mountng plate, makng sure t s level. 4. Securely tghten the lag screws. 3. Poston mountng plate on the wall, makng sure that the top of the mountng plate s algned wth the front edge of the upper cabnet. 1. Dsconnect R edctrs (Jppe Cob net power to outlet. 4. Push the 2 bolts wth toggle nuts through the drywall, and 2. Remove all contents from upper cabnet. fnger tghten the bolts to make sure toggle nuts have opened aganst drywall. 3. Place Upper Cabnet Template aganst the bottom of the upper cabnet, and attach wth tape or thumbtacks. Make sure the template centerlne algns wth the vertcal centerlne on // / / (_... C the rear wall. // // \ // %1?// // //. 1/4-20 x 3" round-head bolt. Mountng plate C.Drywafl D. Sprng toggle nut The "rear wall" arrows must be aganst the rear wall so that the holes cut nto the upper cabnet algn wth the holes n the top of the mcrowave oven. NOTE: If the upper cabnet has a frame around t, trm the template edges so that t fts nsde the frame, aganst the upper cabnet bottom. The template has trm lnes to use as gudes. 4. Make sure the 10Zo' (26.5 cm) dmenson from the rear wall to ponts "D" and "E" on the template s mantaned. 5. Insert lag screw(s) nto the holes drlled nto wall stud(s) n Step 2 of "Installaton for No Wall Studs at Corner Holes" n the "Drll Holes n Rear Wall" secton. 6. Check algnment of mountng plate, makng sure t s level. 7. Securely tghten all lag screws and bolts /lo'' 107/16'' 0 (26.5 ore)/ 8

9 5. Cut the 11/2"(3.8 cm) dameter hole at the crcular shaded area "G" on the template. Ths hole s for the power supply cord. NOTE: If upper cabnet s metal, the supply cord bushng needs to be nstalled around the supply cord hole, as shown. IL. Metal cabnet. Power supply cord bushng 6. Drll 3/8" (10 mm) holes at ponts "D" and "E" on the template. These are for two 1/4-20 x 3" round-head bolts and washers used to secure the mcrowave oven to the upper cabnet. For Roof Ventng Installaton Only 7. Cut 3/4" (19 mm) hole at one corner of the shaded rectangular area "F" on Upper Cabnet Template. 8. Usng a keyhole saw, cut out the rectangular area. n Mc Oven 4=. Mountng plate. Support tabs Wth front of mcrowave oven stll tlted, thread power supply cord through the power supply cord hole n the bottom of the upper cabnet. Excessve Weght Hazard Use two or more people to move and nstall mcrowave oven. Falure to do so can result n back or other njury. IMPORTNT: The control sde of the unt s the heavy sde. Handle the mcrowave oven gently. 1. Place a washer on each 1/4-20 x 3" bolt and place nsde upper cabnet near the 3/8" (10 mm) holes. 2. Make sure the mcrowave oven door s closed and taped shut. 5. Rotate mcrowave oven up toward upper cabnet. NOTE: If ventng through the wall, make sure the damper assembly fts easly nto the vent n the wall cutout. 6. Push mcrowave oven aganst mountng plate and hold n place. NOTE: If mcrowave oven does not need to be adjusted, skp steps If adjustment s requred, rotate mcrowave oven downward. Usng 2 or more people, lft mcrowave oven off of mountng plate, and set asde on a protected surface. 8. Loosen mountng plate screws. djust mountng plate and retghten screws. 9. Repeat steps Wth the mcrowave oven centered, and wth at least one person holdng t n place, nsert bolts through upper cabnet nto mcrowave oven. Tghten bolts untl there s no gap between upper cabnet and mcrowave oven. NOTES: Some upper cabnets may requre bolts longer or shorter than 3" (7.6 cm). Longer or shorter bolts are avalable at most hardware stores. Overtghtenng bolts may warp the top of the mcrowave oven. To avod warpng, wood fller blocks may be added. The blocks must be the same thckness as the space between the upper cabnet bottom and the mcrowave oven. 3. Usng 2 or more people, lft mcrowave oven and hang t on support tabs at the bottom of mountng plate. NOTE: To avod damage to the mcrowave oven, do not grp or use the door or door handle whle the mcrowave oven s beng handled. I. olts

10 For Roof Ventng Installaton Only 1. Insert damper assembly through the cabnet cutout so that the long tab of the damper assembly sldes nto the rased slot of the damper plate. Then secure wth one of the remanng screws removed n Step 1 of "Rotate r Deflector." NOTE: The screw cannot be nstalled f the damper assembly s not postoned as shown. C 1. Refer to the Use and Care Gude for nstructons on how to nstall flters nto your model. Electrcal Shock Hazard Plug nto a grounded 3 prong outlet. 2= D Connect [ t. Screw. Damper assembly C. Long tab (nsde rased slot) D. Upper cabnet cutout E. Damper plate vent to damper assembly.. Vent!. Damper assembly (under vent) E Do not remove ground prong. Do not use an adapter. Do not use an extenson cord. Falure to follow these nstructons can result n death, fre, or electrcal shock. 2. Plug mcrowave oven nto grounded 3 prong outlet. 3. Reconnect power. 4. Check the operaton of mcrowave oven by placng 1 cup (250 ml) of water on the turntable, and programmng a cook tme of 1 mnute at 100% power. Test vent fan and exhaust by operatng the vent fan. 5. If the mcrowave oven does not operate: Check that a household fuse has not blown, or that a crcut breaker has not trpped. Replace the fuse or reset the crcut breaker. If the problem contnues, call an electrcan. Check that the power supply cord s plugged grounded 3 prong outlet. See the Use and Care Gude for troubleshootng nformaton. Installaton s now complete. Save Installaton Instructons for future use. nto a 10

11 VENTING DESIGN SPECIFICTIONS Ths secton s ntended for archtectural desgner and bulder/ contractor reference only. NOTES: Vent materals needed for nstallaton are not provded wth mcrowave hood. We do not recommend usng a flexble metal vent. To avod possble product damage, be sure to vent ar outsde, unless usng recrculaton nstallaton. Do not vent exhaust ar nto concealed spaces, such as spaces wthn walls or celngs, attcs, crawl spaces or garages. For optmal ventng nstallaton, we recommend: usng roof or wall caps that have back draft dampers usng a rgd metal vent usng the most drect route by mnmzng the length of the vent and number of elbows to provde effcent performance usng unformly szed vents usng duct tape to seal all jonts n the vent system usng caulkng compound to seal exteror wall or roof openng around cap not nstallng 2 elbows together, for optmal hood performance If ventng through the wall, be sure that there s proper clearance wthn the wall for the damper to open fully. If ventng through the roof, and rectangular to round transton s used, be sure there s at least 3" (7.6 cm) of clearance between the top of the mcrowave oven and the transton pece. See "Rectangular to Round Transton" llustraton. Rectangular to Round Transton NOTE: The mnmum 3" (7.6 cm) clearance must exst between the top of the mcrowave oven and the rectangular to round transton pece so that the damper can open freely and fully. Recommended f. Roof cap. 6" (15.2 cm) mn. dameter round vent C. Elbow (for wall ventng only) D. Waft cap E. 3 _" x lo" to 6"(8.3x25.4 cm to 15.2 cm) rectangular to round transton pece F. Vent extenson pece, at least 3" (7.6 cm) hgh Standard Fttngs The followng length equvalents are for use when fgurng vent length. See the examples n "Recommended Vent Length." C Roof ventng Roof cap Wall ventng Wall cap D E F G. Rectangular to round transton pece: 3_" x 10" to 6" = 5 ft (8.3 x 25.4 cm to 15.2 cm = 1.5 m). Roof cap: 3 _" x 10" = 24 ft (8.3 x 25.4 cm = 7.3 m) C. 90 elbow: 3¼" x 10" = 25 ft (8.3 x 25.4 cm = 7.6 m) D. 90 elbow: 6" = 10 ft (15.2 cm = 3 m) E. Wall cap: 3¼" x 10" = 40 ft (8.3 x 25.4 cm = 12.2 m) F. 45 elbow: 6" = 5 ft (15.2 cm = 1.5 m) G. 90 flat elbow: 3 _" x 10" = 10 ft (8.3 x 25.4 cm = 3 m) 11

12 Recommended Vent Length 31/4'' x 10" (8.3 x 25.4 cm) rectangular should be used. or 6" (15.2 cm) round vent The total length of the vent system ncludng straght vent, elbow(s), transtons and wall or roof caps must not exceed the equvalent of 140 ft (42.7 m) for ether type of vent. See "Recommended Standard Fttngs" secton for equvalent lengths. For best performance, use no more than three 90 elbows. To calculate the length of the system you need, add the equvalent lengths of each vent pece used n the system. See the followng examples: 31/4'' x 10" (8.3 x 25.4 cm) vent system = 73 ft (22.2 m) total (0.6m) 6 t (1.8m),F SSISTNCE Call your authorzed dealer or servce center. When you call, you wll need the mcrowave oven model number and seral number. oth numbers can be found on the model and seral number plate, whch s located behnd the mcrowave oven door on the front frame of the mcrowave oven. If you need addtonal assstance, call us at our toll free number lsted n the Use and Care Gude, or vst us on the Web. 'Yxsent If any of the nstallaton hardware needs to be replaced, call us at our toll free number lsted n the Use and Care Gude, and reference the approprate part number lsted here. Damper ssembly Part Number Mountng Plate Part Number W Upper Cabnet Template Part Number Mountng Screw Kt (ncludes parts -E n "Parts Suppled" n the "Tools and Parts" secton) Part Number W C. One 3¼" x 10" (8.3 x 25.4 cm) 90 elbow = 25 ft (7.6 m). 1 wall cap = 40 ft (12.2 m) C. 2 ft (0.6 m) + 6 ft (1.8 m) straght = 8 ft (2.4 m) 6" (15.2 cm) vent system = 73 ft (22.2 m) total! Fller Panel Kts are avalable from your dealer to use when nstallng ths mcrowave oven n a 36" (91.4 cm) or 42" (106.7 cm) wde openng. The fller panels come n pars. Each panel s 3" (7.6 cm) wde. ollo 6 ft (1.8m) _![_ C. Two 90 elbows = 20 ft (6.1 m). 1 wall cap = 40 ft (12.2 m) C. 1 rectangular to round transton pece = 5 ft (1.5 m) D. 2 ft (0.6 m) + 6 ft (1.8 m) straght= 8 ft (2.4 m) D. Fller panels Fller Panel Kt Number Whte lack scut Stanless Steel lmond If the exstng vent s round, a rectangular to round transton pece must be used. In addton, a rectangular 3" (7.6 cm) extenson vent between the damper assembly and rectangular to round transton pece must be nstalled to keep the damper from stckng. See your authorzed dealer or servce center for detals ll rghts reserved /06 Prnted n Chna