MICRO-CONTROLLER X (48mm 48mm)

Size: px

Start display at page:

Download "MICRO-CONTROLLER X (48mm 48mm)"

Paula Davidson
5 years ago
Views:

PX series Digital temperature Ctroller DATA SHEET Socket Type With frt dimensis of 48 48mm, this socket type temperature ctroller enables On-Off ctrol, PID ctrol or 8-step ramp/soak functi, using

1 PX series Digital temperature Ctroller DATA SHEET Socket Type With frt dimensis of 48 48mm, this socket type temperature ctroller enables On-Off ctrol, PID ctrol or 8-step ramp/soak functi, using thermocouple, resistance bulb or DC1 to 5V signal as input. Though small-sized, it can be equipped with a variety of functis. MICRO-CONTROLLER X (48mm 48mm) MICRO-CONTROLLER X PXR4 FEATURES 1. PID with auto-tuning, PID self-tuning and fuzzy ctrol are installed as standard. 2. Frt side waterproof specificati in cformity with NEMA4X (standard). 3. Two alarms are equipped, and 8-step ramp/soak functi can be installed as an opti. SPECIFICATIONS 1. General specificatis Power supply voltage Power csumpti Insulati resistance Dielectric strength Input impedance Allowable signal source resistance Allowable wiring resistance Reference juncti compensati accuracy 100 V (-15%) to 240 V (+10%) AC, 50/60 Hz or 24 V (±10%) AC 50/60 Hz, 24 V (±10%) DC When using 100 V AC: 8 VA or less When using 220 V AC: 10 VA or less When using 24 V AC/DC: 10VA 20 MΩ or more (500 V DC) Power supply-ground V AC for 1 min Power supply-others V AC for 1 min Ground-relay output V AC for 1 min Ground-alarm output V AC for 1 min Others V AC for 1 min Thermocouple: 1 MΩ or more Voltage: 450 kω or more Current: 250Ω (external resistor) Thermocouple: 100Ω or less Voltage: 1 kω or less Resistance bulb: 10Ω or less per wire ±1 C (at 23 C) Input value correcti ±10% of measuring range Set value correcti ±50% of measuring range Input filter 0 to sec settable in 0.5 sec steps (first order lag filter) Noise reducti ratio Normal mode noise (50/60 Hz): 50 db or more Comm mode noise (50/60 Hz): 140 db or more 2. Ctrol functi of standard type Ctrol acti Proportial band (P) Integral time (I) Differential time (D) 0 to sec settable in 0.1 sec step On/ acti if P = 0. Proportial acti when I, D = 0. Proportial cycle Hysteresis width Anti-reset windup Input sampling cycle Ctrol cycle 3. Input secti Input signal Measuring range Burnout PID ctrol (with auto tuning, self-tuning) Fuzzy ctrol (with auto tuning) Self tuning 0 to 999.9% of measuring range settable in 0.1% step 0 to 3200 sec settable in 1 sec step 1 to 150 sec settable in 1 sec step Only for relay ctact output or SSR/SSC drive output 0 to 50% of measuring range For On/ acti ly 0 to 100% of measuring range Automatically validated at auto tuning 0.5 sec 0.5 sec Thermocouple : J, K, R, B, S, T, E, N, PLII Resistance bulb : Pt100 Voltage, current: 1 to 5 V DC, 4 to 20 ma DC (Apply current input after cnecting the furnished 250Ω resistor to input terminal.) See measuring range table (Table1) For thermocouple or resistance bulb input Ctrol output upper/lower are selectable 4. Output secti of standard type (ctrol output 1) Ctrol output 1 Select e as follows Relay ctact: SPDT ctact: 220V AC/30V DC, 3A (resistive load) Mechanical life 10 milli operatis (no load) Electrical life 100,000 operatis (rated load) Minimum switching current 100mA (24V DC) SSR / SSC drive (Voltage pulse): ON: 17 to 25 V DC OFF: 0.5V DC or less Max. current: 20mA or less 4 to 20mA DC: Allowable load resistance 600Ω or less EDS Date Oct. 23, 2006

2 PXR4 5. Operati and display secti Parameter setting method Display Status display LED Setting accuracy Indicati accuracy (at 23 C) 6. Alarm (opti) Alarm kind Alarm ON-delay Process alarm output Power ON Lower limit alarm Lower limit alarm (with hold) Digital setting by 3 keys With key lock functi Process value/set value Independent display 4 digits, 7-segment LED Ctrol output, process alarm output 0.1% or less of measuring range Thermocouple: ±(0.5% of measuring range) ±1 digit ±1 C For thermocouple R at 0 to 500 C... ± (1% of measuring range) ±1 digit ±1 C For thermocouple B at 0 to 400 C... ± (5% of measuring range) ±1 digit ±1 C Resistance bulb, voltage/current: ± (0.5% of measuring range) ±1 digit Absolute alarm, deviati alarm, ze alarm with upper and lower limits for each Hold functi available (See the figure below.) Alarm latch, Excitati/n-excitati selecting functi provided Delay setting 0 to 9999 sec settable in 1 sec steps Relay ctact: SPST ctact: 220 V AC/30 V DC, 1 A (resistive load) Mechanical life 10 milli operatis (no load) Electrical life 100,000 operatis (rated load) Minimum switching current 100 ma (5 V DC) MAX 2 points output cycle 0.5 sec What is alarm with hold? The alarm is not turned ON immediately even when the process value is in the alarm band. It turns ON when it goes out the alarm band and enters again. PV (process value) Power OFF Period where lower limit alarm is output Power ON 11. Structure Mounting method External terminal Case material Dimensis Weight Protective structure Outer casing Table 1 Measuring range table Group input signal measuring range( C) measuring range( F) I II Resistance bulb Thermocouple DC voltage DC current Panel flush mounting, DIN rail mounting. (Mounting socket is required for mounting DIN rail.) 8 pins or 11 pins terminals (Socket is required for wiring separately.) Plastic (n-combustible grade UL94V-0 equivalent) mm Approx. 200 g Frt waterproof structure: NEMA4X (IEC standard IP66 equivalent) (when mounted panel with our genuine packing. Waterproof feature unavailable in close mounting of multiple units) Rear case: IEC IP20 Black (frt frame, case) Pt100 J K R B S T E N PL2 1 to 5V 4 to 20mA -150 to to to to to to to to to to 1300 scaling range -238 to to to to to to to to to to to 9999 Note 1: For current input cnect the supplied 250Ω resister at the input terminal. Note 2: Setting cannot be changed to a different group. Note 3: When the measuring range exceeds 1000 C (1832 F), decimal point cannot be used. 7. Other functis Parameter mask Parameter display is disabled by software. functi Ramp/soak 2 program pattern of 4 steps each, or 1 functi (opti) program pattern 8 steps Digital input allows to start/reset the acti. 8. Power failure processing Memory protecti Held by n-volatile memory 9. Self-check Method Program error supervisi by watchdog timer 10. Operati and storage cditis Ambient operating temperature Ambient operating humidity Storage temperature -10 C to 50 C (In low-temperature envirment, start-up time may vary in power activati.) Less than 90% RH (no cdensati) -20 C to 60 C

3 PXR4 Temperature Ctroller Socket Series Ordering Informati (PXR4 Socket Versi) P X R 4 A B S 1 C D 0 A 1 To create a part number f ll in the boxes above with the appropriate number and/or letter from the correspding list below. Frt Panel Size 4 = 1/16 DIN (48x48mm) Box A: Input Signal T = Thermocouple ( C) R = Thermocouple ( F) N = RTD, Pt100 ohm, 3-wire type ( C) S = RTD, Pt100 ohm, 3-wire type ( F) B = 4-20mA DC, 1-5V DC A = 0-20mA DC, 0-5V DC Box B: Ctrol Output 1 A = Relay ctact output C = SSR or SSC drive output E = 4-20mA DC output 1 Box C: Alarm Optis 4 = Ne 5 = Hign.low alarm 1 point G = High/low alarm 2 points Box D: Power Supply V = Standard ( V AC, 50/60Hz) B = 24V AC/DC (50/60Hz) Accessories PXR4 Loader Assembly PXR4 Terminal Cover Program loader for PXR4 Terminal block protective cover Informati subject to change without notice. Prices in USD

4 PXR4 Scope of delivery Scope of delivery Ctroller, panel mounting bracket, watertight packing, instructi manual (as ordered), socket (as ordered), 250Ω resistor (for current input) Opti Shunt resistor 250Ω ±0.1% Model: ZZPPXR1-A190 Insulati block diagram Power supply secti Relay ctact ctrol output 1 Measurement input Internal circuit Voltage pulse, 4 to 20mA DC Alarm relay output 1, 2 ctrol output 1 Note: Basic insulati (dielectric strength 1500 V AC) between blocks delimited by line. Functial insulati (dielectric strength 500 V AC) between blocks delimited by line. N isolated between blocks which are not delimited from each other.

5 OUTLINE DIAGRAM (Unit: mm) 48 Panel 9 1 Mounting frame Water-proof packing t 1 t 8 Panel cutout size (Unit: mm) 45 0 Side stick mounting (n units) (48 x N-3) min. 63min. Note: Waterproof is not available in stick mounting.

MICRO-CONTROLLER X (48mm 48mm)

MICRO-CONTROLLER X (48mm 48mm) PX series Digital temperature Controller DT SHEET Socket Type With front dimensions of 8 8mm, this socket type temperature controller enables OnOff control, PID control or 8step ramp/soak function, using