TA Series. Analog And Non-Indicating Type, PID Control, Set Temperature By Dial. Features. Ordering Information TA S B 4 R P 4 C

Size: px

Start display at page:

Download "TA Series. Analog And Non-Indicating Type, PID Control, Set Temperature By Dial. Features. Ordering Information TA S B 4 R P 4 C"

Lenard Wiggins
5 years ago
Views:

nalog nd Non-Indicating Type, PID Control, Set Temperature y Dial Features Improved control performance with built-in microcomputer dopting new uto-tuning PID control algorithm : Selectable ON/OFF,

1 nalog nd Non-Indicating Type, PID Control, Set Temperature y Dial Features Improved control performance with built-in microcomputer dopting new uto-tuning PID control algorithm : Selectable ON/OFF, PID control (with the external slide SW) Easy to check controlling status with deviation indicators : Deviation LED (red, green), output LED (red) indicators Dial setting output OFF function Sensor broken display function Ordering Information T S R P C Power supply Control method Sensor input type Control output Unit Temperature range for each sensor C Celsius F Fahrenheit Temperature sensor - to -8 to 22 DPt - - to 2 to 22 DPt - K (C) 2 to 2 2 to 92 DPt J (IC) K (C) to 2 to 72 - J (IC) - to 2 to 72 DPt J (IC) K (C) 6 to 6 2 to,2 - - K (C) 8 to 8 2 to, K (C) C to,2 2 to 2, K (C) P DPtΩ J J (IC) K K (C) R Relay output S drive output -2VC /6Hz ON/OFF control & PID control combined Item Size S DIN W8 x H8mm (8-pin plug type) M DIN W72 x H72mm L DIN W96 x H96mm T nalog setting type temperature controller : 8-pin socket (PG-8, PS-8(N)) is sold separately. H-67

2 Series TS TM TL Power supply llowable voltage range Power consumption -2VC /6Hz 9 to % of rated voltage Max. V Size DIN W8 H8mm DIN W72 H72mm DIN W96 H96mm Display method Setting type Deviation LED (red, green), Output LED (red) Dial setting Setting accuracy F.S. ±2% (room temperature 2 ± ) Input type Control Control output Specifications Functions Thermocouples ON/OFF Control PID Control Relay Dielectric strength Vibration Relay life cycle Mechanical Electrical Insulation resistance Noise resistance Memory retention Environment Insulation type pproval DPtΩ (allowable line resistance max. Ω per a wire) K (C), J (IC) Hysteresis: 2 fixed Control period: Relay output - 2 sec. / drive output - 2 sec. 2VDC±2V PV deviation indicatable, Error indicatable 2,VC /6Hz for min. (between input terminal and power terminal).7mm amplitude at frequency of to Hz (for min.) in each X, Y, Z direction for 2 hours Min.,, operations (8, operations/hr) Min., operations (9 operations/hr) Min. MΩ (at VDC megger) ±2kV R-phase, S-phase the square wave noise (pulse width: us) by the noise simulator pprox. years (when using non-volatile semiconductor memory type) mbient temperature - to, storage: -2 to 6 mbient humidity to 8%RH, storage: to 8%RH Double insulation or reinforced insulation (mark:, dielectric strength between the measuring input part and the power part: 2kV) Weight 2 pprox. 2g (approx. 7g) pprox. 76g (approx. g) pprox. 27g (approx. 2g) : Out of room temperature range: elow model is F.S. ±%, Over model is F.S. ±% 2: The weight includes packaging. The weight in parentheses is for unit only. Environment resistance is rated at no freezing or condensation. Connections TS : DPtΩ (-wire type) ( Socket (PG-8, PS-8 (N)) is sold separately) + - RELY OUT RESISTIVE LOD ~ -2VC V /6Hz TM Thermocouple: K (C), J (IC) RELY OUT 22 RESISTIVE LOD ~ -2VC V /6Hz + - H-68

3 nalog Setting Non-Indicating Type, PID Control Connections : DPtΩ (-wire type) Thermocouple: K (C), J (IC) TL -2VC V /6Hz RELY OUT RESISTIVE LOD Dimensions (unit: mm) TS TM TL Panel cut-out D C Series Size C D TS Min. 6 Min TM Min. 9 Min TL Min. Min racket TS TM, TL H-69

4 Terminal cover (sold separately) RM-COVER (72 72mm) 7 RL-COVER (96 96mm) 9 (unit: mm) Unit Description Deviation indicator: It shows deviation of present temperature (PV) based on set temperature (SV) by LED. Input deviation indicator [Deviation indicator: H-7 (green), / (red)] PV deviation temperature Deviation indicator PV deviation temperature Deviation indicator Input sensor OPEN Exceed max. input value indicators flash (every. sec.) indicator flashes (every. sec.) This is the same as Fahrenheit ( ). When power is on, all indicators light for 2 sec., then all indicators turn off and control operation starts. 2. Set temperature (SV) dial: Dial to change set temperature (SV). When changing set temperature, it is applied after 2 sec. for the stable input.. Input sensor type: Indicates sensor type of present value. Input sensor type or input range each product is shown in the below table. Input sensor Range No. Temperature range ( ) Temperature range ( ) to 2 to 22 2 to 2 2 to 92 K (C) to 2 to 72 6 to 6 2 to,2 Thermocouple 8 to 8 2 to,72 C to,2 2 to 2,92 2 to 2 2 to 92 J (IC) to 2 to 72 to 2 to 72 - to -8 to 22 DPtΩ to 2 to 22 2 to 2 2 to 92 to 2 to 72 Set temperature within input range each sensor. Less than or equal to ±2 More than -2 to less than or equal to -. Temperature unit: Indicates temperature unit (, ) of set temperature (SV) and present value (PV).. Temperature range: Indicates temperature range of set temperature (SV). 6. Control output indicator: Turns ON when control output (Relay output/ drive output). 7. Control mode selector switch: Select PID control or ON/OFF control using switch. 8. Terminal: Terminals for external connections. For detail, refer to Connections. indicator turns ON indicators turn ON More than indicator turns ON More than - indicator turns ON More than 2 to less than or equal to indicators turn ON Less than min. input value indicator flashes (every. sec.)

5 nalog Setting Non-Indicating Type, PID Control Mounting TS (8 8mm) Series Other Series Mount the product on the panel, fasten bracket by pushing with tools as shown above. Functions drive output drive output 2VDC module Load Power INPUT LOD Power ON/OFF control ON/OFF control function is for controlling temperature by comparing present temperature (PV) to setting temperature (SV). ON/OFF control is fixed on reverse operation (Heating). Output turns on to supply power to heater when present temperature (PV) falls lower than setting temperature (SV) and the output turns off to turn off heater when present temperature (PV) is higher then setting temperature (SV). Hysteresis is fixed 2 during ON/OFF control. PID control Temperature controller Control output Reverse operation (Heating) Hysteresis STOP Control output could stop without power off by setting the front setting volume to below min. setting range. If control output stops by STOP function, Green indicator in deviation indicator ( ) will flash every sec. Error Error mark will flash (every sec.) in PV indicator when error occurs during the control operation. It will operate normally, if input sensor is connected or returned to normal range. SV Temperature PID constants are suggested and implemented based on self tuning from supply power until reaching set temperature (SV), then self tuning is over after reaching set temperature (SV). When power supply, in case that set temperature (SV) dial points at OFF or self tuning can not be started because present temperature (PV) is higher than set temperature (SV) or hunting occurs during self tuning, output control is switched to proportion band (P) because that is considered to error. t that time, proportion band is fixed at. Control cycle of PID control and proportion control is 2 sec. in relay output model and 2 sec. in drive output model. No Display Description indicators flash If input sensor line is broken or sensor is not connected. 2 indicator flashes If measured sensor input is higher than temperature range. indicator flashes If measured sensor input is lower than temperature range. H-7

TA Series. Analog And Non-Indicating Type, PID Control, Set Temperature By Dial. Features. Ordering Information TA S B 4 R P 4 C

TA Series. Analog And Non-Indicating Type, PID Control, Set Temperature By Dial. Features. Ordering Information TA S B 4 R P 4 C T Series nalog nd Non-Indicating Type, PID Control, Set y Dial Features Improved control performance with built-in microcomputer dopting new uto-tuning PID control algorithm : Selectable ON/OFF, PID control