No mark VAC 50/60Hz, VDC 1 12VDC 2 24VAC 50/60Hz, 24VDC. selectable by output operation mode

Size: px

Start display at page:

Download "No mark VAC 50/60Hz, VDC 1 12VDC 2 24VAC 50/60Hz, 24VDC. selectable by output operation mode"

Marlene Elliott
5 years ago
Views:

TN Series DN W48 H48mm, Universal Voltage Multi-unction Timer eatures Realization of wide range of power supply :100-40V 50/0Hz, 4-40VD universal, 4V 50/0Hz, 4VD universal, 1VD Various output

1 TN Series DN W48 H48mm, Universal Voltage Multi-unction Timer eatures Realization of wide range of power supply :100-40V 50/0Hz, 4-40VD universal, 4V 50/0Hz, 4VD universal, 1VD Various output operation ( kinds modes) Multi time range (1 kinds of time range) Wide control time (0.05sec to 100hour) Easy setting of time, time range, output operation mode Easy to check output status by indicator Please read Safety onsiderations in operation manual before using. Ordering nformation T 8 N tem Time operation Number of plug pins supply No mark V 50/0Hz, 4-40VD 1 1VD 4V 50/0Hz, 4VD N DN EN Time limit DPDT (c) or instantaneous SPDT (1c)+Time limit SPDT (1c) selectable by output operation mode Time limit DPDT (c) nstantaneous SPDT (1c)+Time limit SPDT (1c) 8 8-pin plug type pin plug type T nalog Timer Sockets (8-pin sockets: PG-08, PS-08(N)/11-pin sockets: PG-11, PS-11(N)) are sold separately. Specifications Model T8N- T11DN- T11EN- unction Multi unction Timer ontrol time setting range 0.05sec to 100hour supply Vᜠ 50/0Hz, 4-40VDᜡ universal 4Vᜠ 50/0Hz, 4VDᜡ universal 1VDᜡ llowable voltage range 90 to 110% of rated voltage consumption Max. 4.V (100-40Vᜠ), Max. W (4-40VDᜡ) Max. 4.5V (4Vᜠ), Max. W (4VDᜡ) Max. 1.5W (1VDᜡ) Max. 100ms Max..5V (100-40Vᜠ), Max. 1.5W (4-40VDᜡ) Max. 4V (4Vᜠ), Max. 1.5W (4VDᜡ) Max. 1W (1VDᜡ) Return time Timing operation ON Start Signal ON Start Min. input signal width -,, : pprox. 50ms nput - ontrol output ontact type Time limit DPDT (c) or nstantaneous SPDT (1c)+ Time limit DPDT (c) Time limit SPDT (1c) selectable by output operation mode 50Vᜠ 5 resistive load Min. 10,000,000 operations Min. 100,000 operations (50V 5 resistive load) Max. ±0.% ±10ms Max. ±5% ±50ms ontact capacity Relay Mechanical life cycle Electrical Repeat error SET error Voltage error Max. ±0.5% Temperature error Max. ±% nsulation resistance Over 100MΩ (at 500VD megger) : Refer to time specifications for control time setting range by model. Max. 4.V (100-40Vᜠ), Max. W (4-40VDᜡ) Max. 4.5V (4Vᜠ), Max. W (4VDᜡ) Max. 1.5W (1VDᜡ),, : [No-voltage input] - Short-circuit impedance: Max. 1kΩ, Residual voltage: Max. 0.5V, Open-circuit impedance: Min. 100kΩ nstantaneous SPDT (1c)+ Time limit SPDT (1c) K-

2 Multi unction nalog Timer Specifications Model T8N- T11DN- T11EN- Dielectric strength,000v 50/0Hz for 1 minute T - 1 Noise ±500V the square wave noise (pulse width 1µs) by noise simulator T - immunity T ±kv the square wave noise (pulse width 1µs) by noise simulator Vibration Mechanical 0.5mm amplitude at frequency of 10 to 55Hz (for 1min) in each X, Y, Z direction for 1hour Malfunction 0.5mm amplitude at frequency of 10 to 55Hz (for 1min) in each X, Y, Z direction for 10min Shock Mechanical 00m/s (approx. 0G) in each X, Y, Z direction times Malfunction 100m/s (approx. 10G) in each X, Y, Z direction times Environment mbient temperature -10 to 55, storage: -5 to 5 mbient humidity 5 to 85%RH, storage: 5 to 85%RH pproval ᜢ ᜧ ccessory Bracket Weight pprox. 14.1g (approx. 8.1g) pprox. 1.g (approx. 85g) pprox. 14.g (approx. 8.5g) : The weight includes packaging. The weight in parenthesis is for unit only. Environment resistance is rated at no freezing or condensation. onnections T8N When selecting [], [] output operation mode When selecting [1], [B], [1], [] output operation mode () Photoelectric (B) iber Optic () Door/rea (D) Proximity (E) Pressure () Rotary Encoders (G) onnectors/ onnector ables/ Sensor Distribution Boxes/Sockets (H) Temperature () SSRs / (J) ounters 50V 5 50V 5 (K) Timers 1 8 (nstantaneous 1c) 1 8 (L) Panel (M) Tacho / Speed / Pulse : /D voltage: V 50/0Hz, 4-40VD : 4V 50/0Hz, 4VD D voltage:1vd (N) Display Units (O) Sensor T11DN T11EN V 5 4 (nstantaneous 1c) V 5 (P) Switching Mode Supplies (Q) Stepper Motors & Drivers & (R) Graphic/ Logic Panels (S) ield Network Devices (T) Software : /D voltage: V 50/0Hz, 4-40VD : 4V 50/0Hz, 4VD D voltage:1vd K-

3 TN Series Dimensions (unit: mm) 44.8 Bracket 8-pin, 11-pin socket (sold separately) refer to page G Panel cut-out Min Min Unit Description (lashes for timer operation, Turns ON for timer stop) Time limit output indicatior Time Specifications Time range Time unit Time setting range Time range Time unit Time setting range to 0.5sec to 0.5hour to 1sec to 1hour SE HOUR to 5sec to 5hour 10 1 to 10sec 10 1 to 10hour 0.5 Time range indication Time range setting switch Time unit indication (SE, MN, HOUR, 10H mode) 0.05 to 0.5min 0.5 Output operation mode display part T8N (, 1, B,, 1, mode) T11DN/T11EN (,, 1,, D, mode) Output operation mode setting switch 0.5 to 5hour to 1min 1 1 to 10hour MN 10H to 5min 5 5 to 50hour 10 1 to 10min to 100hour Output Operation Mode T8N Display Output operation mode ON Delay 1 ON Delay1 (One-Shot output) B ON Delay licker (O Start) 1 licker1 (ON Start) nterval T11DN/T11EN Display Output operation mode Signal ON Delay licker (O Start) 1 licker1 (ON Start) Signal O Delay D Signal ON/O Delay nterval K-4

4 Multi unction nalog Timer Output Operation Mode (T8N) Mode Time chart [t: Setting time, t > t-a, Rt: Return time, Rt1>Rt] () Photoelectric (B) iber Optic ON Delay 1 ON Delay1 (One-Shot output) B ON Delay licker (O Start) 1 licker1 (ON Start) nterval 1-4 (8-5) 1- (8-) nstantaneous limit contact N.O. 1- One- Shot output is 0.5sec fixed nstantaneous limit contact N.O (8-5) 1- (8-) nstantaneous limit contact N.O nstantaneous limit contact N.O sec 0.5sec t t t-a Rt1 t t t t t t-a Rt1 t t t () Door/rea (D) Proximity (E) Pressure () Rotary Encoders (G) onnectors/ onnector ables/ Sensor Distribution Boxes/Sockets (H) Temperature () SSRs / (J) ounters (K) Timers (L) Panel (M) Tacho / Speed / Pulse (N) Display Units (O) Sensor (P) Switching Mode Supplies (Q) Stepper Motors & Drivers & (R) Graphic/ Logic Panels (S) ield Network Devices (T) Software n case of, 1 output operation mode, setting time should be over 100ms. f not, it may cause abnornal output operation due to under 100ms of setting time. K-5

5 TN Series Mode Output Operation Mode (T11DN/T11EN) Signal ON Delay Time chart t t1 t [t: Setting time, t=t1+t, t>t-a] licker (O Start) 1 licker1 (ON Start) Signal O Delay t t t-a t t1 t t t t-a t t1 t t t-a t-a t1 t D Signal ON/O Delay nterval f power is cut or the terminal is short-circuited, the titmer will be. f the terminal is short-circuited during a time limit operation, the time will stop. n case of, 1 output operation mode, setting time should be over 100ms. f not, it may cause abnormal output operation due to under 100ms of setting time. t t t-a t1 t t-a t t-a t-a t t t t-a t-a t1 t K-

6 Multi unction nalog Timer Proper Usage nput connection (T11DN/T11EN) circuit of T11DN/EN timer does not use trans. Use isolation transformer which secondary part is not grounded as (igure 1) to cut off peripheral current flow for supplied power to external input deivces. (igure 1) Main circuit <sensor> T11DN/T11EN Rectification circuit <extermal sensor power supply> s (igure ), if using terminal 10 as common terminal of input signal, it may cause damage to inner circuit of T11DN/EN timer. Use terminal as common terminal referring to (igure ). (igure ) (igure ) solation transformer n order to apply input signals (,, ), short-circuit the terminal no. -5, - or -. t may cause internal circuit damage by wrong connections. Do not wire,, signal input line with power line, high voltage line in parallel. ommon Please connect D power input after checking polarity of power. 1VD, 4VD, 4V power supply should be insulated and limited voltage/current or lass, SELV power supply device. When applying the power to the timer, please apply the rated power at the moment by switch, relay, etc. Otherwise it might cause malfunction. When supply the power to the timer, connection shown in (igure 4) might cause malfunction due to leakage current through R and. Please connect R and as shown in (igure 5) to prevent malfunction. (igure 4) (igure 5) R Leakage current T Timer t might cause malfunction if changing the setting time, time range or operation mode during unit operating unit. Please change the setting time, time range or operation mode after cut the power off. Do not use this unit at below places. Place where there are severe vibration or impact. Place where strong alkalis or acids are used. Place where there are direct ray of the sun. Place where strong magnetic field or electric noise are generated. nstallation environment ndoors ltitude max.,000m Pollution degree nstallation category Ⅱ R T Timer () Photoelectric (B) iber Optic () Door/rea (D) Proximity (E) Pressure () Rotary Encoders (G) onnectors/ onnector ables/ Sensor Distribution Boxes/Sockets (H) Temperature () SSRs / (J) ounters (K) Timers (L) Panel (M) Tacho / Speed / Pulse (N) Display Units (O) Sensor (P) Switching Mode Supplies (Q) Stepper Motors & Drivers & (R) Graphic/ Logic Panels (S) ield Network Devices (T) Software K-

Multi Function Timer with Free power, Compact size W38 H42mm

Multi Function Timer with Free power, Compact size W38 H42mm Multi Function with Free power, ompact size W8 H4mm Features Wide power supply range : 100-40VA 50/0Hz, 4-40VD (universal), 4VA 50/0Hz / 4VD (universal), 1VD Various output operations( operation modes)