ELECTRONIC COUNTER (with pre-scaling function) UL File No.: E C-UL File No.: E122222

Transcription

1 EECTRIC (with pre-scaling function) C-S Counters C-S -digit type -digit type pin type type U File No.: E C-U File No.: E Features. Bright and Easy-to-Read Display A brand new bright -color backlight CD display. The easy-to-read screen in any location makes checking and setting procedures a cinch.. Easy to use, simple operation, simple settings Operation modes (input/output modes) can be set easily, using DIP switches on the side panel. Values can be set easily, using key switches on the front panel.. Pre-scaling function provided A pre-scaling function enables conversion of lengths and volumes to any desired values, and displays the results.. Built-in power supply for highcapacitance sensor An internal power supply drives a VDC, ma high-capacitance sensor. (AC power supply types only) Photoelectric switches, proximity switches and encoders can be directly connected.. Dual-path AC sensor can be connected.. Basic insulation between the power supply and the input terminal (only for the sensor type model with power supply) There is no need for caution when connecting between terminals.. Conforms to IP s Weather Resistant Standards The water-proof panel keeps out water and dirt for reliable operation even in poor environments.. -digit or -digit display Two sizes of displays are offered for you to choose the one that suits your needs.. and Pin Type are Both Standard Options The two s are standard options to support either front panel installation or embedded installation.. Compliant with U, c-u and CE.. ow Price All this at an affordable price to provide you with unmatched cost performance. Product types Digit Count speed Operation mode Output Operation Power for sensor Terminal Part No. z/ Kz switchable Maintain output/hold count Maintain output/over count I Maintain output/over count II One shot/over count One shot/recount I One shot/recount II One shot/hold count ( modes) Relay Transistor Relay Transistor to V AC to V DC / V AC to V DC / V AC to V AC to V DC / V AC to V DC / V AC Notes). Rubber packing (ATC) and an mounting frame (AT-DA) are included.. to VAC Tr outputs (-pin terminal, screw-tightening terminal) types are also supported. V DC ma None None V DC ma None None pins pins pins pins pins pins C-PS-R-AC C-PS-R-ACS C-S-R-V C-S-R-VS C-S-T-V C-S-T-VS C-PS-R-AC C-PS-R-ACS C-S-R-V C-S-R-VS C-S-T-V C-S-T-VS Phone:.. - Fax:.. - Web: info@clrwtr.com

2 C-S Part names -digit display type DIP switches Controlled output indicator indicator OCK Counter display Set value display ock indicator switch Set/lock switch SET/OCK C Up keys Down keys (Same for screw ) -digit display type DIP switches Controlled output indicator indicator OCK Counter display Set value display ock indicator switch SET/OCK Up keys Set/lock switch C (Same for screw ) Specifications Rating Contact ife Electrical Mechanical conditions Item Rated operating Rated frequency Rated power consumption Rated control capacity Input mode Max. counting speed Counting input (input, input ) input ock input Input signal Output mode One shot output time Indication Digit Decimal point Pre-scaling Memory Power for senser Contact arrangement Initial contact resistance Contact material Mechanical (contact) Electrical (contact) range Initial withstand Initial insulation resistance (At V DC) Temperature rise Vibration resistance Shock resistance Connection Protective construction Functional Destructive Functional Destructive Ambient temperature Ambient humidity Air pressure AC type to V Ralay output type DC/AC type to V DC/ V AC / z common Max. V A Max. W A V AC (resistive load) ma, V DC Addition ()/Subtraction ()/Direction (DIR)/Individuality (IND)/Phase (PASE) modes selectable by DIP switches z, kz (selectable by DIP switches). ms at z/. ms at kz time: time = : Min. input signal width: ms, ms (selected by DIP switches) Min. input signal width: ms Contact, Open collector input/dc two-wire system sensor Input impedance: kω or less, Input residual : V or less, Open impedance: kω or less, Max. energized : V DC OD-A, OD-B, OD-C, SOT-A, SOT-B, SOT-C, SOT-D, modes selectable by DIP switches s,.s,.s,.s,.,.s -segment CD, Counter value (backlight red ED), Setting value (backlight yellow ED) -digit display type to ( to for setting) -digit display type to ( to for setting) Can be set to three digits. to. (-digit type),. to. (-digit type) EEP-ROM (Overwriting times: ope. or more) V DC (±%) ma Max. Form C mω (at A V DC) Ag alloy/au flush ope. (Except for switch operation parts) ope. (At rated control ) to V AC. to. V DC,. to. V AC Between live and dead metal parts:, Vrms for min (pin type) Between input and output:, Vrms for min Between live and dead metal parts: Min. MΩ (pin type) Between input and output: Min. MΩ Max. C (under the flow of nominal operating current at nominal ) to z ( cycle/min), single amplitude:. mm ( min on axes) to z ( cycle/min), single amplitude:. mm ( h on axes) Min. m/s ( times on axes) Min. m/s ( times on axes) C to C F to F Max. % R (non-condensing) to, h Pa -pin/screw terminal IP (front panel with a rubber gasket) Transistor output type DC/AC type to V DC/ V AC Form A (Open collector) ope. (At rated control ) Phone:.. - Fax:.. - Web: info@clrwtr.com

3 Applicable standard C-S Safety standard EN- Pollution Degree /Over Category II EMC Dimensions (EMI)EN-- Radiation interference electric field strength Noise terminal (EMS)EN-- Static discharge immunity RF electromagnetic field immunity EFT/B immunity Surge immunity Conductivity noise immunity Power frequency magnetic field immunity Voltage dip/instantaneous stop/voltage fluctuation immunity EN Group ClassA EN Group ClassA EN-- kv contact kv air EN-- V/m AM modulation ( Mz to Gz) V/m pulse modulation ( Mz to Mz) EN-- kv (power supply line) kv (signal line) EN-- kv (power line) EN-- V/m AM modulation (. Mz to Mz) EN-- A/m ( z) EN-- ms, % (rated ) ms, % (rated ), ms, % (rated ), ms, % (rated ) mm inch General tolerance: ±. ±. ( (... Pin type (Flush mount/surface mount) type: M. (Flush mount).... ( (. s ((.) ((.) ((.) ((.) SET/OCK C.. (* -digit display type has the same dimensions.) *.*.*.*.*.* * With power supply for sensor * With power supply for sensor Dimensions for flush mounting (with adapter installed) type Rubber gasket ATC (supplied) Panel Mounting frame for flush mount AT-DA (supplied) Pin type Rubber gasket ATC (supplied) Panel Mounting frame for flush mount AT-DA (supplied) pin type pins cap: ATA (sold separately). OCK.. (. (.. OCK.. SET/OCK SET/OCK C C * With power supply for sensor * With power supply for sensor Dimensions for front panel installations DIN rail terminal block -pin type: AT-DFK (sold separately) Installation panel cut-out dimensions The standard panel cut-out dimensions are shown below. Use the mounting frame (AT-DA) and rubber gasket (ATC). Min For connected installations Device installation rail ATA (sold separately). (.). (.) * With power supply for sensor Min When n units are attached in a continuous series, the dimension of (A) is: A = ( n.). A Note : The installation panel thickness should be between and mm. and. inch. Note : For connected installations, the waterproofing ability between the unit and installation panel is lost. Phone:.. - Fax:.. - Web: info@clrwtr.com

4 C-S Terminal layouts and Wiring diagrams Pin type * With power supply for sensor Relay output type Transistor output type Relay output type Transistor output type Input NC Input Input NC Input Input NO Input Input NO Input ock ock ock ock V DC V ma Max. type * With power supply for sensor Relay output type Transistor output type Relay output type Transistor output type Input Input ock NC NO Input Input ock V DC V ma Max. Input Input Input Input ock NO ock NC V DC V ma Max. V DC V ma Max. Note) For connecting the output leads of the transistor output type, refer to ) Transistor output on page. Phone:.. - Fax:.. - Web: info@clrwtr.com

5 Setting the operation mode and counter Setting procedure ) Setting the operation mode (input mode and output mode) Set the input and output modes with the DIP switches on the side of the counter. DIP switches Item DIP switch Output mode Refer to table Minimum reset input signal width ms ms Maximum counter setting z kz Input mode Refer to table Table : Setting the output mode DIP switch No. Output mode SOT-A SOT-B SOT-C SOT-D OD-A OD-B OD-C (See note ) C-S DIP switches (See note ) (Same for -digit, screw-down ) Table : Setting the input mode DIP switch No. Input mode Addition input Subtraction input Directive input Independent input Phase input (See note ) (See note ) (See note ) Notes:) The counter and set value displays will display DIP Err. Notes:) Set the DIP switches before installing the counter on the panel. Notes:) When the DIP SW setting is changed, turn off the power once. Notes:) The DIP switches are set as before shipping. Setting procedure ) Setting the set value Set the set value with the and keys on the front of the counter. Front display section -digit display type Q Counter display W Set value display E Controlled output indicator R indicator T ock indicator Y keys Changes the corresponding digit of the set value in the addition direction (upwards) OCK SET/OCK C U keys Changes the corresponding digit of the set value in the subtraction direction (downwards) I switch s the counting value and the output O SET/OCK switch This is used to handle pre-scaling values, one-shot times, decimal point position settings, and key lock operations (to disable Up key, Down key, and key operations). -digit display type Q Counter display W Set value display E Controlled output indicator R indicator T ock indicator OCK SET/OCK C Y keys Changes the corresponding digit of the set value in the addition direction (upwards) U switch s the counting value and the output I SET/OCK switch This is used to handle pre-scaling values, one-shot times, decimal point position settings, and key lock operations (to disable Up key, Down key, and key operations). Setting procedure ) Setting the input mode The input mode is set using the key switch in the [Display] section on the front of the counter. Decimal point position setting mode Q olding down the [SET/OCK] key, press the key for the second digit to access the decimal point position setting mode. Example) -digit type Decimal point position setting mode display (Example shows default value displayed) W When the setting mode has been accessed, release the [SET/OCK] key. Phone:.. - Fax:.. - Web: info@clrwtr.com

6 C-S E The decimal point is set using the [] and [] keys to specify the nd, rd, and th digits (this applies only to -digit models).(the st digit is set using the [] key or [] key in settings where there is no decimal point (this applies only to -digit models).) Example) -digit type Example shows nd digit displayed using [] key R Press the [] key to set the displayed decimal point position and return to normal operation. Setting the pre-scaling value Q olding down the [SET/OCK] key, press the key for the first digit to access the pre-scaling value setting mode. Example) -digit type Example) -digit type Pre-scaling value setting mode displayed (Example shows default values displayed) W When the setting mode has been accessed, release the [SET/OCK] key. E Use the [] or [] key to set the pre-scaling value (this applies only to -digit models). Select either:. to. (-digit) or. to. (-digit) R Press the [] key to set the displayed pre-scaling value and return to normal operation. Setting the one-shot output time Q olding down the [SET/OCK] key, press the key for the third digit to access the one-shot output time setting mode. Example) -digit type One-shot output time setting mode displayed (Example shows default value displayed) W When the setting mode has been accessed, release the [SET/OCK] key. E Each time the st-digit [] key is pressed, the one-shot output time changes in the following sequence, moving to the right: s. s. s. s. s. s (With a -digit type, the [] key can also be used to move to the left.) R Press the [] key to set the displayed one-shot output time and return to normal operation. Changing the set value. It is possible to change the set value with the up and down keys (- digit type only) even during counting. owever, be aware of the following points. ) If the set value is changed to less than the count value with counting set to the addition direction, counting will continue until it reaches full scale ( with the -digit type and with the -digit type), returns to zero, and then reaches the new set value. If the set value is changed to a value above the count value, counting will continue until the count value reaches the new set value. ) Suppose that thew counter is preset to count down. Whether a preset countdown value is smaller or larger than the count value, the counter counts down to (zero).. If the set value is changed to, the unit will not complete count-up. It starts counting up when the counting value comes to (zero) again. ) Up-count (addition) input When counting is set to the addition direction, counting will continue until full scale is reached ( with the -digit type and with the -digit type), return to zero, and then complete countup. ) Down-count (subtraction) input When counting is set to the subtraction direction, counting will continue until full scale is reached (- with the -digit type and - with the -digit type), and then the display will change to with the -digit type and with the -digit type. The counting value does not become (zero) and so the counter does not count up. ) Directive, independent, and phase inputs The counting value is counted up or down to any number other than once. When it comes to (zero) again, the counter starts counting up. CAUTIS FOR USE For more information regarding the cautions for use of C series counter, refer to page PRECAUTIS IN USING TE C SERIES. Phone:.. - Fax:.. - Web: info@clrwtr.com

7 Operation mode. Input mode For the input mode, you can choose one of the following five modes Addition Subtraction Directive Independent Phase DIR IND PASE C-S Input mode Addition Operation IN or IN works as an input block (gate) for the other input. *Minimum input signal width z:. ms; kz:. ms Example where IN is the counting input and IN is the input block (gate). IN A A A A Blocked IN n- n- n- n n n- n- n- Count-up completed Example where IN is the counting input and IN is the input block (gate). IN Blocked Blocked A A A A Subtraction IN n- n n n- n- n- n- Count-up completed * A must be more than the minimum input signal width. Directive DIR IN is the counting input and IN is the addition or subtraction directive input. IN adds at level and subtracts at level. IN IN Counting A A A A Addition Subtraction Addition * A must be more than the minimum input signal width. IN is addition input and IN is subtraction input. IN Independent IN IND Counting * IN and IN are completely independent, so there is no restriction on signal timing. Addition when the IN phase advances beyond IN, and subtraction when the IN phase advances beyond IN. IN Phase PASE IN Counting Phase advance B B Phase retard * B must be more than the minimum input signal width. Phone:.. - Fax:.. - Web: info@clrwtr.com

8 C-S. Output mode For the output mode, you can choose one of the following seven modes Maintain output/hold count Maintain output/over count I Maintain output/over count II One shot/over count One shot/recount I One shot/recount II One shot/hold count Output mode Maintain output old count OD-A Maintain output Over count I OD-B Maintain output Over count II OD-C One shot Over count SOT-A One shot Recount I SOT-B One shot Recount II SOT-C One shot old count SOT-D OD-A OD-B OD-C SOT-A SOT-B SOT-C SOT-D Operation count-up completion and until resetting. During that time, the count display does not change from that at count-up completion. count-up completion and until resetting. owever, counting is possible despite completion of count-up. count-up completion and until the next signal enters. owever, counting is possible despite completion of countup. count-up completion for one shot output time. Counting is possible despite completion of count-up. count-up completion for one shot output time. Counting is possible despite completion of count-up. owever, reset occurs simultaneous with completion of count-up. While output is being maintained, restarting of the count is not possible count-up completion for one shot output time. Counting is possible despite completion of count-up. owever, reset occurs simultaneous with output. count-up completion for one shot output time. During that time, the count display does not change from that at count-up completion. occurs simultaneous with output. Output control Output control (Example when input mode is either addition or subtraction) n- n- n- n Unable n- n- n n n - - n- n- n n n - - Output control n- n- n n n - - Output control Approx. s n- n- n n- n- (automatic) Output control Output control Output control Approx. s n- n n - n n- Approx. s (automatic) n- n n n- Unable Approx. s (automatic) Phone:.. - Fax:.. - Web: info@clrwtr.com

9 Input connections Signal input type C-S ) Open collector ) For output (PC, sensor etc.) V DC (Photoelectric sensor, proximity sensor, etc.) V DC Output Output -pin type ock Input input Input input V DC output -pin type ock Input input Input V DC input output ) Contact input ) For a rotary encoder Relay, switches etc. B phase A phase V DC -pin type ock Input input Input input -pin type Input Input V DC output Input, input, and reset input specifications Impedance during short-circuit: kω max. (At Ω, the outflow current is approximately ma.) Residual during short-circuit: V max. Impedance when released: kω min. Max. applied : VDC max. ock input specifications Impedance during short-circuit: kω max. (At Ω, the outflow current is approximately. ma.) Residual during short-circuit: V max. Impedance when released: kω min. Max. applied : DVC max. The contact relay should be one which can open/close V,. ma. * There is no V DC with - V DC/ V AC types. ) For a dual-line sensor -pin type Input Input input What is the prescale function? The prescale function converts the count into an actual value (amount) and displays it. Example For a device that outputs pulses when m has been fed:. Set decimal position to the last rd place.. Set the prescale value to. (/). m.ft Dual-line sensor specifications eakage current:. ma max. Breaker capacitance: ma min. Residual :. V max. Usable : Runs on VDC Encoder pulse SET/OCK C Can be set to easy-to-understand unit. Prescale value:. * If a dual-line sensor is connected to a - VDC/ VAC type, VDC (. to. VDC) and VAC (. to. VAC) should be applied to the power supply of the counter. pulses SET/OCK C Phone:.. - Fax:.. - Web: info@clrwtr.com