MICRO-CONTROLLER X (48mm 48mm)

Size: px

Start display at page:

Download "MICRO-CONTROLLER X (48mm 48mm)"

Eleanore Crawford
5 years ago
Views:

PX series Digital temperature Controller DT SHEET Socket Type With front dimensions of 8 8mm, this socket type temperature controller enables OnOff control, PID control or 8step ramp/soak function,

1 PX series Digital temperature Controller DT SHEET Socket Type With front dimensions of 8 8mm, this socket type temperature controller enables OnOff control, PID control or 8step ramp/soak function, using thermocouple, resistance bulb or DC to V signal as input. Though smallsized, it can be equipped with a variety of functions. MICROCONTROLLER X (8mm 8mm) MICROCONTROLLER X FETURES. PID with autotuning, PID selftuning and fuzzy control are installed as standard.. Front side waterproof specification in conformity with NEMX (standard).. Two alarms are equipped, and 8step ramp/soak function can be installed as an option. SPECIFICTIONS. General specifications Power supply voltage Power consumption Insulation resistance Dielectric strength Input impedance llowable signal source resistance llowable wiring resistance Reference junction compensation accuracy V (%) to V (%) C, / Hz or V (±%) C / Hz, V (±%) DC When using V C: 8 V or less When using V C: V or less When using V C/DC: V MΩ or more ( V DC) Power supplyground... V C for min Power supplyothers... V C for min Groundrelay output... V C for min Groundalarm output... V C for min Others... V C for min Thermocouple: MΩ or more Voltage: kω or more Current: Ω (external resistor) Thermocouple: Ω or less Voltage: kω or less Resistance bulb: Ω or less per wire ± C (at C) Input value correction ±% of measuring range Set value correction ±% of measuring range Input filter to 9. sec settable in. sec steps (first order lag filter) Noise reduction ratio Normal mode noise (/ Hz): d or more Common mode noise (/ Hz): d or more. Control function of standard type Control action Proportional band (P) Integral time (I) Differential time (D) to sec settable in. sec step On/ action if P =. Proportional action when I, D =. Proportional cycle Hysteresis width ntireset windup Input sampling cycle Control cycle. Input section Input signal Measuring range urnout PID control (with auto tuning, selftuning) Fuzzy control (with auto tuning) Self tuning to 999.9% of measuring range settable in.% step to sec settable in sec step to sec settable in sec step Only for relay contact output or SSR/SSC drive output to % of measuring range For On/ action only to % of measuring range utomatically validated at auto tuning. sec. sec Thermocouple : J, K, R,, S, T, E, N, PLII Resistance bulb : Pt Voltage, current: to V DC, to m DC (pply current input after connecting the furnished Ω resistor to input terminal.) See measuring range table (Table) For thermocouple or resistance bulb input Control output upper/lower are selectable. Output section of standard type (control output ) Control output Select one as follows Relay contact: SPDT contact: V C/V DC, (resistive load) Mechanical life million operations (no load) Electrical life, operations (rated load) Minimum switching current m (V DC) SSR / SSC drive (Voltage pulse): ON: to V DC OFF:.V DC or less Max. current: m or less to m DC: llowable load resistance Ω or less EDSa Date pr.,

2 . Operation and display section Parameter setting method Display Status display LED Setting accuracy Indication accuracy (at C). larm (option) larm kind larm ONdelay Process alarm output Power ON Lower limit alarm Lower limit alarm (with hold) Digital setting by keys With key lock function Process value/set value Independent display digits, segment LED Control output, process alarm output.% or less of measuring range Thermocouple: ±(.% of measuring range) ± digit ± C For thermocouple R at to C... ± (% of measuring range) ± digit ± C For thermocouple at to C... ± (% of measuring range) ± digit ± C Resistance bulb, voltage/current: ± (.% of measuring range) ± digit bsolute alarm, deviation alarm, zone alarm with upper and lower limits for each Hold function available (See the figure below.) larm latch, Excitation/nonexcitation selecting function provided Delay setting to 9999 sec settable in sec steps Relay contact: SPST contact: V C/ V DC, (resistive load) Mechanical life million operations (no load) Electrical life, operations (rated load) Minimum switching current m ( V DC) MX points output cycle. sec What is alarm with hold? The alarm is not turned ON immediately even when the process value is in the alarm band. It turns ON when it goes out the alarm band and enters again. PV (process value) Power OFF on Period where lower limit alarm is output Power ON on on. Structure Mounting method External terminal Case material Dimensions Weight Protective structure Outer casing Table Measuring range table Group input signal measuring range( C) measuring range( F) I II Resistance bulb Thermocouple DC voltage DC current Panel flush mounting, DIN rail mounting. (Mounting socket is required for mounting DIN rail.) 8 pins or pins terminals (Socket is required for wiring separately.) Plastic (noncombustible grade UL9V equivalent) mm pprox. g Front waterproof structure: NEMX (IEC standard IP equivalent) (when mounted on panel with our genuine packing. Waterproof feature unavailable in close mounting of multiple units) Rear case: IEC IP lack (front frame, case) Pt J K R S T E N PL to V to m to 8 to 8 to to to 8 to to to 8 to to scaling range 8 to to to 9 to 9 to to 9 8 to 8 to to to 999 to 9999 Note : For current input connect the supplied Ω resister at the input terminal. Note : Setting cannot be changed to a different group. Note : When the measuring range exceeds C (8 F), decimal point cannot be used.. Other functions Parameter mask Parameter display is disabled by software. function Ramp/soak program pattern of steps each, or function (option) program pattern 8 steps Digital input allows to start/reset the action. 8. Power failure processing Memory protection Held by nonvolatile memory 9. Selfcheck Method Program error supervision by watchdog timer. Operation and storage conditions mbient operating temperature mbient operating humidity Storage temperature C to C (In lowtemperature environment, startup time may vary in power activation.) Less than 9% RH (no condensation) C to C

3 PXR Model Code Configuration PXR 8 S 9 Digit Specification <Front dimensions> 8 8mm <Input signal> Thermocouple C Thermocouple F Resistance bulb Pt wire type I ( C) Resistance bulb Pt wire type I ( F) to V DC to m DC Resistance bulb Pt wire type II ( C) <Control output > Relay contact output Voltage pulse output (V DC) to m DC output <Terminal form> Socket type 8 <Revision code> 9 <Optional specifications> None larm ( pc.) Rampsoak larm ( pc.) Rampsoak larm ( pcs.) larm ( pcs.) Rampsoak <Instruction manual> <Power supply voltage> None to V C English to V C None V C/V DC English V C/V DC <Socket> None For rail mounting (8pin screw terminal) For panel mounting (8pin screw terminal) For rail mounting (pin screw terminal) For panel mounting (pin screw terminal) Note Note Note Note Note Note Note Note T R N S W C E S F G N V C Note) Type: TP8X Note) Type: TP8S Note) Type: TPX Note) Type: TPS Note) Input terminal (Pt input) assignment is same as PXW/PXZ/PXV. Note) Input terminal (Pt input) assignment is different from PXW/PXZ/PXV, but in case of thermocouple input terminal assignment is same. Input signal, measurement range, and set value at the time of deliver are as follows. When thermocouple is specified: Thermocouple K, Measurement range; to C, Set value; C When resistance bulb is specified: Pt, Measurement range; to C, Set value; C When voltage/current is specified: Scaling; to %, Set value; % For the cases other than the above, specify input signal and measurement range. Input signal of the thermocouple and the resistance bulb can be switched by key operation on the front panel. Control action is set to reverse action when delivered. The reverse action and normal action can be switched by key operation on the front panel.

4 Scope of delivery Scope of delivery Controller, panel mounting bracket, watertight packing, instruction manual (as ordered), socket (as ordered), Ω resistor (for current input) Option Shunt resistor Ω ±.% Model: ZZPPXR9 Insulation block diagram Power supply section Relay contact control output Measurement input Internal circuit Voltage pulse, to m DC larm relay output, control output Note: asic insulation (dielectric strength V C) between blocks delimited by line. Functional insulation (dielectric strength V C) between blocks delimited by line. Non isolated between blocks which are not delimited from each other.

5 OUTLINE DIGRM (Unit: mm) 8 Panel 9 Mounting frame Waterproof packing t t 8 Panel cutout size (Unit: mm). Side stick mounting (n units). (8 x N).. min. min. Note: Waterproof is not available in stick mounting.

6 CONNECTION DIGRM () With alarm functions pin socket When compatible with PXW/PXZ/PXV thermocouple input terminal (When either one of the following is selected for the th digit of the code symbols: T, R, W, and ) Note that the terminal layout of the resistance bulb input type differs from that of PXW/PXZ/PXV. CONTROL OUTPUT NOTE Ω INPUTS DC to m DC to V R.T.D. DC to m OUTPUT SSR/SSC DRIVING OUTPUT RY OUTPUT 8 LRM OUTPUT COMMON LRM OUTPUT 9 LRM OUTPUT T.C. POWER C to V C/DC V /Hz When compatible with PXW/PXZ/PXV resistance bulb input terminal (When either one of the following is selected for the th digit of the code symbols: N and S ) Note that the terminal layout of the thermocouple input type differs from that of PXW/PXZ/PXV. CONTROL OUTPUT INPUTS DC to m OUTPUT SSR/SSC DRIVING OUTPUT RY OUTPUT LRM OUTPUT COMMON T.C. R.T.D. 8 9 LRM OUTPUT LRM OUTPUT POWER C to V C/DC V /Hz NOTE : Use the Ω resistance (accessory).

7 () Without alarm functions 8pin socket When compatible with PXW/PXZ/PXV thermocouple input terminal (When either one of the following is selected for the th digit of the code symbols: T, R, W, and ) Note that the terminal layout of the resistance bulb input type differs from that of PXW/PXZ/PXV. CONTROL OUTPUT NOTE Ω DC to m INPUTS RY OUTPUT 8 DC to V R.T.D. T.C. POWER C to V C/DC V /Hz SSR/SSC DRIVING OUTPUT DC to m OUTPUT When compatible with PXW/PXZ/PXV resistance bulb input terminal (When either one of the following is selected for the th digit of the code symbols: N and S ) Note that the terminal layout of the thermocouple input type differs from that of PXW/PXZ/PXV. CONTROL OUTPUT INPUTS RY OUTPUT SSR/SSC DRIVING OUTPUT DC to m OUTPUT T.C. R.T.D. 8 POWER C to V C/DC V /Hz NOTE : Use the Ω resistance (accessory).

8 OUTLINE DIGRM (Unit: mm) Without alarm TP8S TYPE (FOR PNEL MOUNTING) TP8X TYPE (FOR RIL MOUNTING) φ TERMINL SCREW M. 8 TERMINL SCREW M φ. HOLE MX. ±. φ. MOUNTING HOLE With alarm TPX TYPE (FOR RIL MOUNTING) TPS TYPE (FOR PNEL MOUNTING) φ. HOLE 8 TERMINL SCREW M..8.. MX. φ TERMINL SCREW M ±. φ. MOUNTING HOLE Caution on Safety *efore using this product, be sure to read its instruction manual in advance. International Sales Div Sales Group Gate City Ohsaki, East Tower,, Osaki chome, Shinagawaku, Tokyo, Japan Phone: 88, 8 Fax: 8 Information in this catalog is subject to change without notice. Printed in Japan

MICRO-CONTROLLER X (48mm 48mm)

MICRO-CONTROLLER X (48mm 48mm) PX series Digital temperature Ctroller DATA SHEET Socket Type With frt dimensis of 48 48mm, this socket type temperature ctroller enables On-Off ctrol, PID ctrol or 8-step ramp/soak functi, using thermocouple,