TEST REPORT EN Information technology equipment Safety Part 1: General requirements

Transcription

1 Test Report issued under the responsibility of: TEST REORT EN Information technology equipment Safety art 1: General requirements Report Number.... : SA L Date of issue... : Total number of pages Testing Laboratory... : Address... : Dongguan Anci Electronic Technology Co., Ltd. 1-2 Floor, Building A, No.11, Headquarters 2 Road, Songshan Lake Hi-tech Industrial Development Zone, Dongguan City, Guangdong r., China. Engineer by (name + signature)... : Night Li Approved by (+ signature)... : Joe Long Applicant s name... : Address...: Manufacturer s name.: Address...: First Factory s name. : Address...: Test specification: Standard...: Test procedure...: SAHAB TECHNOLOGY. OFFICE 21-QIBLA TOWER-FAHAD AL SALEM ST.-QIBLA- STATE OF KUWAIT. SAHAB TECHNOLOGY. OFFICE 21-QIBLA TOWER-FAHAD AL SALEM ST.-QIBLA- STATE OF KUWAIT. SAHAB TECHNOLOGY. OFFICE 21-QIBLA TOWER-FAHAD AL SALEM ST.-QIBLA- STATE OF KUWAIT. EN :2006/A11:2009/A1:2010/A12:2011/A2:2013 CE Non-standard test method..: Test Report Form No.... : Test Report Form(s) Originator... : IEC60950_1F SGS Fimko Ltd Master TRF... : Dated Copyright 2014 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE), Geneva, Switzerland. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

2 Report No.: SA L age 2 of 45 Test item description... : Trade Mark... : Manufacturer... : OE Switch XonTel SAHAB TECHNOLOGY. Model/Type reference...: XT-1600G, XT-2400G Ratings...: Input rating: Vac, 50/60Hz, 3.5A Output rating: 52V 4.8A List of Attachments (including a total number of pages in each attachment): -Attachment 1: National Different (19 pages) -Attachment 2: hoto document (6 pages) Summary of testing: Tests performed (name of test and test clause): 1. Max. ambient temperature 35 C. 2. Following tests performed during evaluation Clause(s) Test(s) Input Current Test Durability of Marking Test Discharge of Capacitors SELV limits for Normal Conditions SELV limits for Abnormal Conditions Limited Current Circuits (Bridging components) Resistance of Earthing Circuit Humidity Conditioning Working Voltage over Insulation TABLE: clearance and creepage distance measurements TABLE: distance through insulation measurements Steady Force Test, 250N Impact Test (Steel Ball) Drop Test Maximum Temperature Test Touch Current and E current 5.2 Electric Strength Test 5.3 Fault Condition Test All tests was performed on model XT-2400G The EUT passed the test. Testing location: All tests as described in Test Case and Measurement Sections were performed at the laboratory described on cover page. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

3 Report No.: SA L age 3 of 45 Copy of marking plate : The artwork below may be only a draft. The use of certification marks on a product must be authorized by the respective NCBs that own these marks. Note:Since similar label used, only label for models above listed to represent other similar ones. The manufacture name or trademark would be remarked on label. Remark: - The above markings are the minimum requirements required by the safety standard. For the final productions samples, the additional markings which do not give rise to misunderstanding may be added. - The height of CE marking should be minimum 5mm high and the height of WEEE directive symbol should be minimum 7mm high. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

4 Report No.: SA L age 4 of 45 Test item particulars... : Equipment mobility...: [x] movable [] hand-held [] transportable [] stationary [] for building-in [] direct plug-in Connection to the mains...: [] pluggable equipment [] type A [] type B [] permanent connection [x] detachable power supply cord [] non-detachable power supply cord [] not directly connected to the mains Operating condition...: [x] continuous [] rated operating / resting time: Access location...: [x] operator accessible [] restricted access location [] Built-in component, consider in end system Over voltage category (OVC)...: [] OVC I [x] OVC II [] OVC III [] OVC IV [] other: Mains supply tolerance (%) or absolute mains supply ±10% values...: Tested for IT power systems... : [] Yes IT testing, phase-phase voltage (V)... : [x] No Class of equipment...: [x] Class I [] Class II [] Class III [] Not classified Considered current rating of protective device as 16A part of the building installation (A)...: ollution degree (D)... : [] D 1 [x] D 2 [] D 3 I protection class... : I20 Altitude during operation (m)... : 2000 Altitude of test laboratory (m)... : <500m Mass of equipment (kg)... : Approx. 2.94kg ossible test case verdicts: - test case does not apply to the test object... : - test object does meet the requirement... : (ass) - test object does not meet the requirement... : F (Fail) Testing... : Date of receipt of test item... : Date(s) of performance of tests... : to Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

5 Report No.: SA L age 5 of 45 General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. (see Enclosure #) refers to additional information appended to the report. (see appended table) refers to a table appended to the report. Throughout this report a point is used as the decimal separator. General product information: OE switch, Model No.: XT-2400G Intend to use as Information Technology Equipment. 1. The maximum operating temperature is 35 C. 2. The top enclosure is sealed with bottom enclosure are sealed together by screw fixed. 3. The models XT-1600G, XT-2400G are identical to each other,except the model name different. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

6 Report No.: SA L age 6 of 45 IEC Clause Requirement + Test Result - Remark Verdict 1 GENERAL 1.5 Components General Comply with IEC or relevant component standard Components, which were found to affect safety aspects, comply with the requirements of this standard or within the safety aspects of the relevant IEC component standards. See Critical Component Table for details Evaluation and testing of components Components, which are certified to IEC and/or national standards, are used correctly within their ratings or had been evaluated during this approval Thermal controls No thermal controls Transformers Transformer used is suitable for the intended application and complies with the relevant requirements of the standard and particularly with those of Annex C Interconnecting cables Interconnecting cables comply with the relevant requirements of this standard. Interconnection cables is used to provide SELV/LS/nonhazardous energy level power to other equipment Capacitors bridging insulation Between primary and secondary: Y1 capacitor (CY6 and CY7) according to IEC primary capacitor X2 type (CX1 and CX2) according to IEC Resistors bridging insulation Resistors bridging functional, basic or supplementary insulation Resistors bridging double or reinforced insulation between a.c. mains and other circuits Resistors bridging double or reinforced insulation between a.c. mains and antenna or coaxial cable Functional only Components in equipment for IT power systems Surge suppressors Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

7 Report No.: SA L age 7 of 45 IEC Clause Requirement + Test Result - Remark Verdict General rotection of VDRs Bridging of functional insulation by a VDR Bridging of basic insulation by a VDR Bridging of supplementary, double or reinforced insulation by a VDR 1.6 ower interface AC power distribution systems Input current Steady state input current of the equipment did not exceed the rated current by more than 10% under Maximum Normal Load. Maximum Normal Load is continuous operation at rated output load Voltage limit of hand-held equipment This appliance is not handheld equipment Neutral conductor Neutral conductor is treated as a line conductor for insulation purposes. 1.7 Marking and instructions ower rating and identification markings ower rating marking Multiple mains supply connections...: Rated voltage(s) or voltage range(s) (V)... : V~ Symbol for nature of supply, for d.c. only... : AC source Rated frequency or rated frequency range (Hz)... : 50/60Hz Rated current (ma or A)... : 3.5A Identification markings Manufacturer s name or trade-mark or identification mark... : Copy of marking plate Model identification or type reference... : Copy of marking plate Symbol for Class II equipment only... : Other markings and symbols... : Other symbols do not give rise to misunderstanding Safety instructions and marking Operating/safety instructions made available to the user General Sufficient information provide in the safety instruction. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

8 Report No.: SA L age 8 of 45 IEC Clause Requirement + Test Result - Remark Verdict Disconnect devices Overcurrent protective device IT power distribution systems Operator access with a tool Ozone Short duty cycles Supply voltage adjustment... : Methods and means of adjustment; reference to installation instructions... : ower outlets on the equipment... : Fuse identification (marking, special fusing characteristics, cross-reference)... : Fuse (F1,F2,F3) on the primary circuit marking provided on CB: F1: T6.3A/250V F2: T6.3A/250V F3: T3.15A/250V Wiring terminals rotective earthing and bonding terminals... : Terminals for a.c. mains supply conductors Terminals for d.c. mains supply conductors Controls and indicators Identification, location and marking... : Colours... : Symbols according to IEC : Markings using figures... : Isolation of multiple power sources... : Thermostats and other regulating devices... : Durability Removable parts Replaceable batteries... : No battery provided. Language(s)... : Equipment for restricted access locations... : 2 ROTECTION FROM HAZARDS 2.1 rotection from electric shock and energy hazards rotection in operator access areas No access with test finger and test pin to any hazardous parts. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

9 Report No.: SA L age 9 of 45 IEC Clause Requirement + Test Result - Remark Verdict Access to energized parts See above. Test by inspection... : See above. Test with test finger (Figure 2A)... : See above. Test with test pin (Figure 2B)... : See above. Test with test probe (Figure 2C)... : No TNV Battery compartments Access to ELV wiring Working voltage (Vpeak or Vrms); minimum distance through insulation (mm) Access to hazardous voltage circuit wiring Energy hazards... : Manual controls No manual controls Discharge of capacitors in equipment Capacity: Measured voltage (V); time-constant (s)... : CX1=CX2=0.47μF Discharge resistor: R15=R16=0.6MΩ L to N (power switch ON): Vpeak=396V, 37% of Vpeak=146.52V s. L to E (power switch ON) Vpeak=312V, 37% of Vpeak=131.72V s. L to N (power switch OFF): Vpeak=388V, 37% of Vpeak=143.56V s. L to E (power switch OFF): Vpeak=320V, 37% of Vpeak=119.41V s Energy hazards d.c. mains supply Connected to a.c. mains. a) Capacitor connected to the d.c. mains supply.. : b) Internal battery connected to the d.c. mains supply... : Audio amplifiers... : Not such equipment rotection in service access areas rotection in restricted access locations 2.2 SELV circuits General requirements SELV levels are maintained after single fault condition. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

10 Report No.: SA L age 10 of 45 IEC Clause Requirement + Test Result - Remark Verdict Voltages under normal conditions (V)... : Between any conductors of the SELV circuit 42.4 V K or 60 V DC are not exceeded Voltages under fault conditions (V)... : Single fault did not cause excessive voltage in accessible SELV circuit. Limits of 71 V K and 120 V DC were not exceed Connection of SELV circuits to other circuits... : SELV circuits are only connected to other secondary circuits. SELV circuit and all interconnected circuits separated from primary by reinforced or double insulation. SELV circuit does not exceed the SELV limits under normal and fault conditions. 2.3 TNV circuits No TNV circuits used Limits Type of TNV circuits... : Separation from other circuits and from accessible parts General requirements rotection by basic insulation rotection by earthing rotection by other constructions... : Separation from hazardous voltages Insulation employed... : Connection of TNV circuits to other circuits Insulation employed... : Test for operating voltages generated externally 2.4 Limited current circuits General requirements See below Limit values 20.16mA Frequency (Hz)... : 28.8KHz Measured current (ma)... : 8.6mA Measured voltage (V)... : 17.2V Measured circuit capacitance (nf or µf)... : CY6=CY7=2200pF Connection of limited current circuits to other circuits Output circuit as limited current circuit connected to Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

11 Report No.: SA L age 11 of 45 IEC Clause Requirement + Test Result - Remark Verdict primary via one bridging capaictor 2.5 Limited power sources a) Inherently limited output b) Impedance limited output c) Regulating network limited output under normal operating and single fault condition The output comply with table 2B, both under normal operating conditions and after single fault in the regulating network. d) Overcurrent protective device limited output Max. Output voltage (V), max. Output current (A), max. Apparent power (VA)... : Current rating of overcurrent protective device (A).: Use of integrated circuit (IC) current limiters (see appended table 2.5) 2.6 rovisions for earthing and bonding rotective earthing Functional earthing rotective earthing and protective bonding conductors General Size of protective earthing conductors Rated current (A), cross-sectional area (mm 2 ), AWG... : Size of protective bonding conductors Rated current (A), cross-sectional area (mm 2 ), AWG... : rotective current rating (A), cross-sectional area (mm 2 ), AWG... : Resistance of earthing conductors and their terminations; resistance (Ω), voltage drop (V), test current (A), duration (min)... : Ω 32A/2min Colour of insulation... : Terminals General rotective earthing and bonding terminals Rated current (A), type, nominal thread diameter (mm)... : Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

12 Report No.: SA L age 12 of 45 IEC Clause Requirement + Test Result - Remark Verdict Separation of the protective earthing conductor from protective bonding conductors Integrity of protective earthing Interconnection of equipment Components in protective earthing conductors and protective bonding conductors Disconnection of protective earth Appliance inlet used for disconnection of protective earth arts that can be removed by an operator Appliance inlet used for disconnection of protective earth arts removed during servicing Corrosion resistance Screws for protective bonding Reliance on telecommunication network or cable distribution system 2.7 Overcurrent and earth fault protection in primary circuits Basic requirements rotective devices are integrated in the equipment. Instructions when protection relies on building installation Faults not simulated in The protection devices are well dimensioned and mounted Short-circuit backup protection Building installation is considered as providing shortcircuit backup protection Number and location of protective devices... : One protective device in the "LIVE" phase rotection by several devices Warning to service personnel... : 2.8 Safety interlocks No safety interlocks used General principles rotection requirements Inadvertent reactivation Fail-safe operation rotection against extreme hazard Moving parts Overriding Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

13 Report No.: SA L age 13 of 45 IEC Clause Requirement + Test Result - Remark Verdict Switches, relays and their related circuits Separation distances for contact gaps and their related circuits (mm)... : Overload test Endurance test Electric strength test Mechanical actuators 2.9 Electrical insulation roperties of insulating materials Humidity conditioning 48 h Relative humidity (%), temperature ( C)... : 95%RH, 30 C Grade of insulation Functional, basic, supplementary, double or reinforced insulation Separation from hazardous voltages Method(s) used... : Method Clearances, creepage distances and distances through insulation General See , and Frequency... : Considered ollution degrees... : Reduced values for functional insulation Considered Intervening unconnected conductive parts Considered Insulation with varying dimensions Special separation requirements Insulation in circuits generating starting pulses Determination of working voltage General RMS working voltage (See appended table ) eak working voltage (See appended table ) Clearances General Mains transient voltages a) AC mains supply... : 240V a.c. and Overvoltage Category II b) Earthed d.c. mains supplies... : Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

14 Report No.: SA L age 14 of 45 IEC Clause Requirement + Test Result - Remark Verdict c) Unearthed d.c. mains supplies... : d) Battery operation... : Clearances in primary circuits (see appended table and ) Clearances in secondary circuits Sub-clause considered Clearances in circuits having starting pulses Transients from a.c. mains supply... : Transients from d.c. mains supply... : Transients from telecommunication networks and cable distribution systems... : Measurement of transient voltage levels a) Transients from a mains supply For an a.c. mains supply... : For a d.c. mains supply... : b) Transients from a telecommunication network : Creepage distances See appended table and General CTI rating for all materials of minimum Material group and comparative tracking index CTI tests... : Material group IIIb; 100 <= CTI < Minimum creepage distances (see appended table and ) Solid insulation General See below Distances through insulation (see appended table ) Insulating compound as solid insulation No such construction used Semiconductor devices Approved opto-coupler used Cemented joints No such construction Thin sheet material General Separable thin sheet material Used in and around transformer T1. Number of layers (pcs)... : 2 layers Non-separable thin sheet material Thin sheet material standard test procedure Electric strength test Thin sheet material alternative test procedure (see appended table 5.2) Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

15 Report No.: SA L age 15 of 45 IEC Clause Requirement + Test Result - Remark Verdict Electric strength test Insulation in wound components Approved triple insulated wire used in T Wire in wound components Working voltage... : a) Basic insulation not under stress... : b) Basic, supplementary, reinforced insulation... : c) Compliance with Annex U... :. Two wires in contact inside wound component; angle between 45 and : Wire with solvent-based enamel in wound components Electric strength test Routine test hysical separation provided by insulating tube and insulation tape Additional insulation in wound components Working voltage... : - Basic insulation not under stress... : - Supplementary, reinforced insulation... : Construction of printed boards See below Uncoated printed boards (see appended table and ) Coated printed boards Insulation between conductors on the same inner surface of a printed board Insulation between conductors on different layers of a printed board Distance through insulation Number of insulation layers (pcs)... : Single layer CB Component external terminations (see appended table and ) Tests on coated printed boards and coated components Sample preparation and preliminary inspection Thermal conditioning Electric strength test Abrasion resistance test Thermal cycling Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

16 Report No.: SA L age 16 of 45 IEC Clause Requirement + Test Result - Remark Verdict Test for ollution Degree 1 environment and insulating compound Tests for semiconductor devices and cemented joints Approved opto-coupler used Enclosed and sealed parts 3 WIRING, CONNECTIONS AND SULY 3.1 General Current rating and overcurrent protection Internal wires are UL recognized wiring which is VC insulated, rated VW-1 or FT-1, and having gauge suitable for current intended to be carried rotection against mechanical damage Wires do not touch sharp edges which could damage the insulation and cause hazard Securing of internal wiring The wires are secured by soldering and additional fixed by glue so that a loosening of the terminal connection is unlikely Insulation of conductors The insulation of the individual conductors suitable for the application and the working voltage. For the insulation Material see Beads and ceramic insulators Screws for electrical contact pressure Insulating materials in electrical connections Self-tapping and spaced thread screws Termination of conductors All conductors are reliably secured. 10 N pull test Sleeving on wiring 3.2 Connection to a mains supply Means of connection See below Connection to an a.c. mains supply Appliance inlet Connection to a d.c. mains supply Only a.c. mains supply. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

17 Report No.: SA L age 17 of 45 IEC Clause Requirement + Test Result - Remark Verdict Multiple supply connections Only for one mains connection ermanently connected equipment Unit is not a permanently connected equipment. Number of conductors, diameter of cable and conduits (mm)... : Appliance inlets ower supply cords AC power supply cords Type... : Rated current (A), cross-sectional area (mm 2 ), AWG... : DC power supply cords Cord anchorages and strain relief Mass of equipment (kg), pull (N)... : Longitudinal displacement (mm)... : rotection against mechanical damage Cord guards Diameter or minor dimension D (mm); test mass (g)... : Radius of curvature of cord (mm)... : Supply wiring space Not permanent connection or non-detachable power cord type. 3.3 Wiring terminals for connection of external conductors Wiring terminals Connection of non-detachable power supply cords Screw terminals Conductor sizes to be connected Rated current (A), cord/cable type, cross-sectional area (mm 2 )... : Wiring terminal sizes Rated current (A), type, nominal thread diameter (mm)... : Wiring terminal design Grouping of wiring terminals Stranded wire Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

18 Report No.: SA L age 18 of 45 IEC Clause Requirement + Test Result - Remark Verdict 3.4 Disconnection from the mains supply General requirement See below Disconnect devices Appliance inlet used ermanently connected equipment Not permanently connected equipment arts which remain energized When inlet is disconnected no remaining parts with hazardous voltage in the equipment Switches in flexible cords None Number of poles single-phase and d.c. equipment The inlet disconnects both poles simultaneously Number of poles three-phase equipment Single phase equipment Switches as disconnect devices lugs as disconnect devices Interconnected equipment Not interconnected equipment Multiple power sources Only one supply connection provided. 3.5 Interconnection of equipment General requirements See below for details Types of interconnection circuits... : SELV interconnection circuits via secondary output connector ELV circuits as interconnection circuits No ELV interconnection Data ports for additional equipment No such ports 4 HYSICAL REQUIREMENTS 4.1 Stability Angle of 10 Test force (N)... : 4.2 Mechanical strength General See below for details. Rack-mounted equipment Steady force test, 10 N Steady force test, 30 N No internal enclosure. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

19 Report No.: SA L age 19 of 45 IEC Clause Requirement + Test Result - Remark Verdict Steady force test, 250 N Location: Outside enclosure Impact test Location: Outside enclosure Fall test Swing test Drop test; height (mm)... : Location:Top enclosure/ Side enclosure/ Bottom enclosure Stress relief test Cathode ray tubes No CRT in the unit. icture tube separately certified... : High pressure lamps No high pressure lamp provided Wall or ceiling mounted equipment; force (N)... : Not wall or ceiling mounted equipment. 4.3 Design and construction Edges and corners Edges and corners of the enclosure are rounded Handles and manual controls; force (N)...: No handles or controls provided Adjustable controls Securing of parts All hazardous parts are fixed to retain position in event of termination failure Connection by plugs and sockets Direct plug-in equipment Torque... : Compliance with the relevant mains plug standard... : Heating elements in earthed equipment No heating elements provided Batteries No batteries provided. - Overcharging of a rechargeable battery - Unintentional charging of a non-rechargeable battery - Reverse charging of a rechargeable battery - Excessive discharging rate for any battery Oil and grease Dust, powders, liquids and gases Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

20 Report No.: SA L age 20 of 45 IEC Clause Requirement + Test Result - Remark Verdict Containers for liquids or gases Flammable liquids... : Quantity of liquid (l)... : Flash point ( C)... : Radiation No radiation General Ionizing radiation Measured radiation (pa/kg)... : Measured high-voltage (kv)... : Measured focus voltage (kv)... : CRT markings... : Effect of ultraviolet (UV) radiation on materials art, property, retention after test, flammability classification... : Human exposure to ultraviolet (UV) radiation... : Lasers (including laser diodes) and LEDs Lasers (including laser diodes) Laser class... : Light emitting diodes (LEDs) Other types... : 4.4 rotection against hazardous moving parts General rotection in operator access areas... : Household and home/office document/media shredders rotection in restricted access locations... : rotection in service access areas rotection against moving fan blades General Not considered to cause pain or injury. A).: Is considered to cause pain, not injury. B) : Considered to cause injury. C) : rotection for users Use of symbol or warning : rotection for service persons Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

21 Report No.: SA L age 21 of 45 IEC Clause Requirement + Test Result - Remark Verdict Use of symbol or warning : 4.5 Thermal requirements General The equipment and its component parts did not attain excessive temperatures during normal operation. See Table 4.5 for details Temperature tests See Table 4.5 for details. Normal load condition per Annex L... : Maximum Normal Load is continuous operation at rated output load Temperature limits for materials (see appended table 4.5) Touch temperature limits (see appended table 4.5) Resistance to abnormal heat... : 4.6 Openings in enclosures Top and side openings Dimensions (mm)... : No openings provided Bottoms of fire enclosures Construction of the bottomm, dimensions (mm).. : No openings provided Doors or covers in fire enclosures Openings in transportable equipment Constructional design measures Dimensions (mm)... : Evaluation measures for larger openings Use of metallized parts Adhesives for constructional purposes Conditioning temperature ( C), time (weeks)... : 4.7 Resistance to fire Reducing the risk of ignition and spread of flame See below for details. Method 1, selection and application of components wiring and materials Method 2, application of all of simulated fault condition tests Materials with the required flammability classes are used Conditions for a fire enclosure Fire enclosure is not necessary arts requiring a fire enclosure. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

22 Report No.: SA L age 22 of 45 IEC Clause Requirement + Test Result - Remark Verdict arts not requiring a fire enclosure Materials General See below for details Materials for fire enclosures Minimum V Materials for components and other parts outside fire enclosures Materials for components and other parts inside fire enclosures All internal materials are rated minimum V-2 or are mounted on a WB rated minimum V Materials for air filter assemblies Materials used in high-voltage components 5 ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS 5.1 Touch current and protective conductor current General See Sub-clauses to for details Configuration of equipment under test (EUT) Single connection to an a.c. mains supply Equipment has only one mains connection Redundant multiple connections to an a.c. mains supply Simultaneous multiple connections to an a.c. mains supply Test circuit Single phase equipment intended only for connection to star TN system Application of measuring instrument Test made to 10 by 20 cm metal foil in contact with accessible non-conductive part. Annex D.1 used Test procedure Test measurements see appended table 5.1 Supply voltage (V)... : Measured touch current (ma)... : Max. Allowed touch current (ma)... : Measured protective conductor current (ma)... : Max. Allowed protective conductor current (ma).. : Equipment with touch current exceeding 3,5 ma General... : Simultaneous multiple connections to the supply Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

23 Report No.: SA L age 23 of 45 IEC Clause Requirement + Test Result - Remark Verdict Touch currents to telecommunication networks and cable distribution systems and from telecommunication networks Limitation of the touch current to a telecommunication network or to a cable distribution system No TNV. Supply voltage (V)... : Measured touch current (ma)... : Max. Allowed touch current (ma)... : Summation of touch currents from telecommunication networks a) EUT with earthed telecommunication ports... : b) EUT whose telecommunication ports have no reference to protective earth 5.2 Electric strength p General See below for details. p Test procedure See Table 5.2 for details. p 5.3 Abnormal operating and fault conditions rotection against overload and abnormal operation See Table 5.3 for details Motors Transformers Transformers are constructed in accordance with the applicable Sub-clauses and Annex C Functional insulation... : By short circuit Electromechanical components Audio amplifiers in ITE... : Simulation of faults See Table 5.3 for details Unattended equipment Compliance criteria for abnormal operating and fault conditions See Table 5.3 for details During the tests No fire or molten metal occurred and no deformation of enclosure during the tests After the tests No reduction of clearance and creepage distance. Electric strength test is made on basic, supplementary and reinforced insulation after test. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

24 Report No.: SA L age 24 of 45 IEC Clause Requirement + Test Result - Remark Verdict 6 CONNECTION TO TELECOMMUNICATION NETWORKS 6.1 rotection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment rotection from hazardous voltages Separation of the telecommunication network from earth Requirements Supply voltage (V)... : Current in the test circuit (ma)... : Exclusions... : 6.2 rotection of equipment users from overvoltages on telecommunication networks Separation requirements Electric strength test procedure Impulse test Steady-state test Compliance criteria 6.3 rotection of the telecommunication wiring system from overheating Max. Output current (A)... : Current limiting method... : 7 CONNECTION TO CABLE DISTRIBUTION SYSTEMS 7.1 General 7.2 rotection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment 7.3 rotection of equipment users from overvoltages on the cable distribution system 7.4 Insulation between primary circuits and cable distribution systems General Voltage surge test Impulse test A ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE UL Recognized material used Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

25 Report No.: SA L age 25 of 45 IEC Clause Requirement + Test Result - Remark Verdict A.1 Flammability test for fire enclosures of movable equipment having a total mass exceeding 18 kg, and of stationary equipment (see ) A.1.1 Samples... : Wall thickness (mm)... : A.1.2 Conditioning of samples; temperature ( C)... : A.1.3 Mounting of samples... : A.1.4 Test flame (see IEC ) Flame A, B, C or D... : A.1.5 Test procedure A.1.6 Compliance criteria Sample 1 burning time (s)... : Sample 2 burning time (s)... : Sample 3 burning time (s)... : A.2 Flammability test for fire enclosures of movable equipment having a total mass not exceeding 18 kg, and for material and components located inside fire enclosures (see and ) A.2.1 Samples, material... : Wall thickness (mm)... : A.2.2 Conditioning of samples; temperature ( C)... : A.2.3 Mounting of samples... : A.2.4 Test flame (see IEC ) Flame A, B or C... : A.2.5 Test procedure A.2.6 Compliance criteria Sample 1 burning time (s)... : Sample 2 burning time (s)... : Sample 3 burning time (s)... : A.2.7 Alternative test acc. To IEC , cl. 5 and 9 Sample 1 burning time (s)... : Sample 2 burning time (s)... : Sample 3 burning time (s)... : A.3 Hot flaming oil test (see 4.6.2) A.3.1 Mounting of samples A.3.2 Test procedure A.3.3 Compliance criterion Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

26 Report No.: SA L age 26 of 45 IEC Clause Requirement + Test Result - Remark Verdict B ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see and 5.3.2) B.1 General requirements osition... : Manufacturer... : Type... : Rated values... : B.2 Test conditions B.3 Maximum temperatures B.4 Running overload test B.5 Locked-rotor overload test Test duration (days)... : Electric strength test: test voltage (V)... : B.6 Running overload test for d.c. motors in secondary circuits B.6.1 General B.6.2 Test procedure B.6.3 Alternative test procedure B.6.4 Electric strength test; test voltage (V)... : B.7 Locked-rotor overload test for d.c. motors in secondary circuits B.7.1 General B.7.2 Test procedure B.7.3 Alternative test procedure B.7.4 Electric strength test; test voltage (V)... : B.8 Test for motors with capacitors B.9 Test for three-phase motors B.10 Test for series motors Operating voltage (V)... : C ANNEX C, TRANSFORMERS (see and 5.3.3) osition... : Transformer (T1) Manufacturer... : See appended table Type... : See appended table Rated values... : See appended table Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

27 Report No.: SA L age 27 of 45 IEC Clause Requirement + Test Result - Remark Verdict Method of protection... : Inherent C.1 Overload test See Table 5.3 for details. C.2 Insulation See Table 5.2 for details. rotection from displacement of windings... : Fixing by insulation tape and bobbin D ANNEX D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS (see 5.1.4) D.1 Measuring instrument D.2 Alternative measuring instrument E ANNEX E, TEMERATURE RISE OF A WINDING (see ) F ANNEX F, MEASUREMENT OF CLEARANCES AND CREEAGE DISTANCES (see 2.10 and Annex G) G ANNEX G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM CLEARANCES G.1 Clearances G.1.1 General G.1.2 Summary of the procedure for determining minimum clearances G.2 Determination of mains transient voltage (V) G.2.1 AC mains supply... : G.2.2 Earthed d.c. mains supplies... : G.2.3 Unearthed d.c. mains supplies... : G.2.4 Battery operation... : G.3 Determination of telecommunication network transient voltage (V)... : G.4 Determination of required withstand voltage (V) G.4.1 Mains transients and internal repetitive peaks... : G.4.2 Transients from telecommunication networks... : G.4.3 Combination of transients G.4.4 Transients from cable distribution systems G.5 Measurement of transient voltages (V) a) Transients from a mains supply For an a.c. mains supply For a d.c. mains supply Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

28 Report No.: SA L age 28 of 45 IEC Clause Requirement + Test Result - Remark Verdict b) Transients from a telecommunication network G.6 Determination of minimum clearances... : H ANNEX H, IONIZING RADIATION (see ) J ANNEX J, TABLE OF ELECTROCHEMICAL OTENTIALS (see ) Metal(s) used... : K ANNEX K, THERMAL CONTROLS (see and 5.3.8) K.1 Making and breaking capacity K.2 Thermostat reliability; operating voltage (V)... : K.3 Thermostat endurance test; operating voltage (V)... : K.4 Temperature limiter endurance; operating voltage (V)... : K.5 Thermal cut-out reliability K.6 Stability of operation L ANNEX L, NORMAL LOAD CONDITIONS FOR SOME TYES OF ELECTRICAL BUSINESS EQUIMENT (see and 4.5.2) L.1 Typewriters L.2 Adding machines and cash registers L.3 Erasers L.4 encil sharpeners L.5 Duplicators and copy machines L.6 Motor-operated files L.7 Other business equipment Maximum Normal Load is continuous operation at rated output load. M ANNEX M, CRITERIA FOR TELEHONE RINGING SIGNALS (see 2.3.1) M.1 Introduction M.2 Method A M.3 Method B M.3.1 Ringing signal M Frequency (Hz)... : M Voltage (V)... : M Cadence; time (s), voltage (V)... : Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

29 Report No.: SA L age 29 of 45 IEC Clause Requirement + Test Result - Remark Verdict M Single fault current (Ma)... : M.3.2 Tripping device and monitoring voltage... : M Conditions for use of a tripping device or a monitoring voltage M Tripping device M Monitoring voltage (V)... : N ANNEX N, IMULSE TEST GENERATORS (see , , , , 7.3.2, and Clause G.5) N.1 ITU-T impulse test generators N.2 IEC impulse test generator ANNEX, NORMATIVE REFERENCES Q ANNEX Q, Voltage dependent resistors (VDRs) (see ) a) referred climatic categories... : b) Maximum continuous voltage... : c) ulse current... : R ANNEX R, EXAMLES OF REQUIREMENTS FOR QUALITY CONTROL ROGRAMMES R.1 Minimum separation distances for unpopulated coated printed boards (see ) R.2 Reduced clearances (see ) S ANNEX S, ROCEDURE FOR IMULSE TESTING (see ) S.1 Test equipment S.2 Test procedure S.3 Examples of waveforms during impulse testing T ANNEX T, GUIDANCE ON ROTECTION AGAINST INGRESS OF WATER (see 1.1.2) U ANNEX U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED INSULATION (see ) Approved triple insulation wire used (see appended table 1.5.1) Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

30 Report No.: SA L age 30 of 45 IEC Clause Requirement + Test Result - Remark Verdict V ANNEX V, AC OWER DISTRIBUTION SYSTEMS (see 1.6.1) V.1 Introduction V.2 TN power distribution systems W ANNEX W, SUMMATION OF TOUCH CURRENTS W.1 Touch current from electronic circuits W.1.1 Floating circuits W.1.2 Earthed circuits W.2 Interconnection of several equipments W.2.1 Isolation W.2.2 Common return, isolated from earth W.2.3 Common return, connected to protective earth X ANNEX X, MAXIMUM HEATING EFFECT IN TRANSFORMER TESTS (see clause C.1) X.1 Determination of maximum input current X.2 Overload test procedure Y ANNEX Y, ULTRAVIOLET LIGHT CONDITIONING TEST (see ) Y.1 Test apparatus... : Y.2 Mounting of test samples... : Y.3 Carbon-arc light-exposure apparatus... : Y.4 Xenon-arc light exposure apparatus... : Z ANNEX Z, OVERVOLTAGE CATEGORIES (see and Clause G.2) AA ANNEX AA, MANDREL TEST (see ) BB ANNEX BB, CHANGES IN THE SECOND EDITION CC ANNEX CC, Evaluation of integrated circuit (IC) current limiters CC.1 General CC.2 Test program 1.: CC.3 Test program 2.: Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

31 Report No.: SA L age 31 of 45 IEC Clause Requirement + Test Result - Remark Verdict DD ANNEX DD, Requirements for the mounting means of rack-mounted equipment DD.1 General DD.2 Mechanical strength test, variable N..: DD.3 Mechanical strength test, 250N, including end stops : DD.4 Compliance : EE ANNEX EE, Household and home/office document/media shredders EE.1 General EE.2 Markings and instructions Use of markings or symbols : Information of user instructions, maintenance and/or servicing instructions : EE.3 Inadvertent reactivation test : EE.4 Disconnection of power to hazardous moving parts: Use of markings or symbols : EE.5 rotection against hazardous moving parts Test with test finger (Figure 2A) : Test with wedge probe (Figure EE1 and EE2) : Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

32 Report No.: SA L age 32 of TABLE: List of critical components Object/part No. ManuFacturer/ trademark Type/model Technical data Standard (Edition / year) Metal Enclosure Various Various Metallic, min. 0.6mm thickness ower Switch NINGBO YINZHOU LIHE ELECTRONIC CO LTD (Alternate) AC Connector (CN1) DC FAN Zhe Jiang Bei Er Jia Electronic Co., Ltd. HUIZHOU CITY TAIJI ELECTROINCS INDUSTRIAL CO LTD SHENZHEN BAODIKAI ELECTRONIC CO LTD IEC/EN RL3 250Vac,6A,85 C IEC/EN , UL1054 S8A Series 250Vac,6A,85 C EC/EN , UL1054 Mark(s) of conformity 1 ) Tested in equipment UL E VDE UL E TA VAC, 85 C. UL 1977 UL E BDM12025S DC 12V 0.3A, min. 66 CFM, min RM CB Various Various V-1 or better, 130 C Fuse (F1,F2) SHENZHEN LANSON ELECTRONICS CO LTD (Alternate) XC ELECTRONICS (SHENZHEN) COR LTD Fuse (F3) XC ELECTRONICS (SHENZHEN) COR LTD (Alternate) Honghu Bluelight Electronic Co., Ltd. Mylar sheet YY-CK11 around CB (Alternate) BOLUO EVERSUN ELECTRONICS LANT Jiangsu Yuxing Film Technology Co.,Ltd UL 507 UL 796 UL SMT T6.3A, 250V IEC/EN IEC/EN UL248 5TE T6.3A, 250V IEC/EN IEC/EN UL248 32F T3.15A 250V IEC/EN IEC/EN UL248 6TE T3.15A 250V IEC/EN IEC/EN UL248 V-0, 130 C, Min. Thickness 0.25mm 6021 VTM-2, 105 C, Min. Thickness 0.25mm UL 94, UL746C UL 94, UL746C UL E UL VDE UL E VDE UL E VDE UL E VDE UL E UL E UL E Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

33 Report No.: SA L age 33 of 45 Varistor (MOV1, THINKING TVR14471 Min.300V AC IEC/EN VDE MOV2, MOV3) IEC/EN ELECTRONIC 85 C,V-0 (test UL E UL 1449 INDUSTRIAL CO by UL for LTD 6KV/3KA combination pulse) (Alternate) SHANTOU HIGH- 14D471K Min.300V AC IEC/EN VDE IEC/EN NEW 105 C,V-0 (test UL 1449 TECHNOLOGY by UL for UL E DEVELOMNT ZONE SONGTIAN ENTERRISE CO 6KV/3KA combination pulse) LTD (Alternate) Cerglass MFG lnc 14D471K Min.300V AC IEC/EN VDE IEC/EN C,V-0 (test UL 1449 by UL for UL E KV/3KA combination pulse) Thermistor (RT1) Various Various Min.2A, 2.5ohm UL1434 UL X-Capacitor (CX1,CX2) (Alternate) Bleeder Resistor (R15, R16) SHANTOU HIGH- NEW TECHNOLOGY DEVELOMNT ZONE SONGTIAN ENTERRISE CO LTD SHENZHEN HAOTIAN ELECTRONIC CO LTD MX MX Max. 0.47uF, 275Vac, 100 C, X2 Type Max. 0.47uF, 275Vac, 100 C, X2 Type Various Various Rated 0.6M ohm, Min. 1/2W. IEC/EN/UL IEC/EN/UL IEC/EN UL E VDE UL E VDE Tested in appliance Line choke (LF1) Various Various 130 C IEC/EN Test with appliance --Magnet wire Various Various 130 C UL 1446 UL Line choke (L1) Various Various 130 C IEC/EN Test with appliance --Magnet wire Various Various 130 C UL 1446 UL Line filter (L2) Various Various 130 C IEC/EN Test with appliance --Bobbin Chang Chun lastics Co Ltd T375J (MC), V-0, 150 C, minimum thickness 0.75mm UL 94, UL 746C UL E59412 Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

34 Report No.: SA L age 34 of 45 --Magnet wire Various Various 130 C UL 1446 UL Transistor (Q2) Various Various Min. 5A, Min. 600V Diode bridge (BD1) E-Capacitor (C17) Y-Capacitor (CY2,CY3) (Alternate) (Alternative) (Alternative) Y-Capacitor (CY6,CY7) (optional) (Alternate) Optocoupler (U5, U7) (Alternate) Transformer (T1) --Insulation tape --Bobbin Various Various Min. 2A, Min. 600V Various Various 450V, 180µF, 105 C JYA-NAY CO., LTD. Dong Guan City DaFu Electronic Co., Ltd. MURATA MFG CO LTD YINAN DON'S ELECTRONIC COMONENT CO LTD JYA-NAY CO., LTD. Dong Guan City DaFu Electronic Co., Ltd. EVERLIGHT ELECTRONICS CO LTD Bright Led Electronics Corp. Shenzhen Hi-Net Technology Company Limited Chang Shu Liang Yi Tape Industry Co Ltd Chang Chun lastics Co Ltd JN CT7 Y2 Series KX CT81 JN CT7 EL817 BC-817C Max pf, min. 250Vac, 125 C, Y1 type Min. 250 V, max pf min. 85 C.Y2 type Maximum 2200pF, minimum 250Vac, 125 C, Y1 type, Maximum 2200pF, minimum 250Vac, 125 C, Y2 type, Max pf, min. 250Vac, 125 C, Y1 type Max pf, min. 250Vac, 125 C, Y1 type Dti=0.5mm, int. dcr=6.0mm, ext. dcr=8.0mm, 100 C Dti>0.4mm, int. dcr 7.6mm, ext. dcr 8.0mm,100 C IEC/EN IEC/EN IEC/EN IEC/EN/UL IEC/EN/UL IEC/EN/UL IEC/EN/UL IEC/EN/UL IEC/EN/UL IEC/EN , UL1577 EN , IEC/EN , UL1577 Test with appliance Test with appliance Test in appliance UL E VDE UL E VDE UL E37921 VDE ULE VDE UL E VDE UL E VDE VDE UL E VDE UL E XT-2400G Class B IEC/EN Tested with appliance LY C UL 510 UL E T375J (MC), V-0, 150 C, minimum thickness 0.75mm UL 94, UL 746C UL E59412 Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

35 Report No.: SA L age 35 of 45 --Magnet wire -Triple insulation wire (Alternate) -Varnish Transformer (T2) --Insulation tape --Bobbin --Magnet wire -Triple insulation wire (Alternate) -Varnish SHENZHEN EASTLIGHT CHEMICAL CO LTD Shanghai Xiangxiang Electron Co., Ltd Hui Zhou Golden Ocean Magnet Wire Factory ELANTAS ELECTRICAL INSULATION ELANTAS DG INC Shenzhen Hi-Net Technology Company Limited Chang Shu Liang Yi Tape Industry Co Ltd Chang Chun lastics Co Ltd SHENZHEN EASTLIGHT CHEMICAL CO LTD Shanghai Xiangxiang Electron Co., Ltd Hui Zhou Golden Ocean Magnet Wire Factory ELANTAS ELECTRICAL INSULATION ELANTAS DG INC DFL-8033-(a) 130 C UL 1446 UL E TKW-B 130 C UL 2353 UL E VDE XYW-B 130 C UL 2353 VDE UL E (X) 130 C UL 1446 UL E75225 XT-2400G Class B IEC/EN Tested with appliance LY C UL 510 UL E T375J (MC), V-0, 150 C, minimum thickness 0.75mm UL 94, UL 746C UL E59412 DFL-8033-(a) 130 C UL 1446 UL E TKW-B 130 C UL 2353 UL E VDE XYW-B 130 C UL 2353 VDE UL E (X) 130 C UL 1446 UL E75225 Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

36 Report No.: SA L age 36 of TABLE: Electrical data (in normal conditions) U (V/Hz) I (A) Irated (A) (W) Fuse # Ifuse (A) Condition/status For model: XT-2400G V/50Hz F1/F2/F Load with 52V/4.8A 90V/50Hz F1/F2/F Load with 52V/4.8A 100V/50Hz F1/F2/F Load with 52V/4.8A 100V/60Hz F1/F2/F Load with 52V/4.8A 240V/50Hz F1/F2/F Load with 52V/4.8A 240V/60Hz F1/F2/F Load with 52V/4.8A 264V/50Hz F1/F2/F Load with 52V/4.8A 264V/60Hz F1/F2/F Load with 52V/4.8A Supplementary information: c) 1) TABLE: max. V, A, VA test Voltage (rated) (V) Current (rated) (A) Voltage (max.) (V) Current (max.) (A) VA (max.) (VA) For model: supplementary information: Supplied by: 2.2 TABLE: evaluation of voltage limiting components in SELV circuits Component (measured between) max. voltage (V) (normal operation) Voltage Limiting Components V peak V d.c. For model: XT-2400G T1 pin A to B T1 pin B to Q Q4 T1 pin A to C T1 pin C to Q Q5 Fault test performed on voltage limiting components For model: XT-2400G With Q4 in D to S short-circuit # Voltage measured (V) in SELV circuits (V peak or V d.c.) Output terminal: 0Vpeak Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

37 Report No.: SA L age 37 of 45 With Q5 in D to S short-circuit # Output terminal: 0Vpeak supplementary information: #=Unit shut down, no hazard; Supplied by 240Vac/60Hz 2.5 TABLE: Limited power source measurement Limits Measured Comments Note(s): Table: working voltage measurement Location RMS voltage (V) eak voltage (V) Comments For model: XT-2400G T2 in1 to in A T2 in2 to in A T2 in3 to in A T2 in4 to in A Vpeak and Vrms T2 in1 to in B T2 in2 to in B T2 in3 to in B T2 in4 to in B T2 in1 to in C T2 in2 to in C T2 in3 to in C T2 in4 to in C T1 in1 to in A T1 in2 to in A T1 in3 to in A T1 in4 to in A T1 in1 to in B T1 in2 to in B T1 in3 to in B T1 in4 to in B CY CY Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

38 Report No.: SA L age 38 of 45 U5 in 1to U5 in 1to U5 in 2to U5 in 2to U4 in 1to U4 in 1to U4 in 2to U4 in 2to Note: Input 240Vac/60Hz *The maximum value measured for representing all models and TABLE: Clearance and creepage distance measurements Clearance (cl) and creepage distance (cr) at/of/between: U peak (V) U r.m.s. (V) Required cl (mm) cl (mm) Required cr (mm) cr (mm) Basic: Line to neutral before fuse Different polarities of fuse F Different polarities of fuse F Different polarities of fuse F ri. trace to earth trace of CB under LF ri. F2 trace to earth trace Core of T1 to rimary winding Core of T1 to secondary winding Core of T2 to rimary winding Core of T2 to secondary winding Reinforced: rimary winding to Secondary winding of T rimary winding to Secondary winding of T rimary trace to secondary trace of bottom CB under CY7 rimary trace to secondary trace of bottom CB under U rimary trace to secondary trace of bottom CB under T rimary trace to secondary trace of bottom CB under T Notes: 1) Core of transformer T1 is considered as ri. part. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

39 Report No.: SA L age 39 of TABLE: Distance through insulation measurements Distance through insulation (DTI) at/of: U peak (V) U rms (V) Test voltage(v) Required DTI(mm) DTI (mm) Bobbin of transformer Vac Optcoupler U Vac Note(s):. 4.5 TABLE: Thermal requirements Supply voltage (V)... : Test A: 90V/60 Hz Lable up Test A: 90V/60 Hz Lable up Test B : 264V/ 60 lable down Test B : 264V/6 0 lable down - Ambient Tmin ( C )... : Tma=3 5 degree C (shifte d) Tma=3 5 degree C (shifted ) Tma= 35 degre e C (shifte d) Tma=5 degree C (shifted ) - Ambient Tmax ( C )... : Maximum measured temperature T of part/at: T ( C) allowed Tmax ( C) Location A A B B -- Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

40 Report No.: SA L age 40 of 45 For model: XT-2400G CX L LF CX MOV CB under Q CB under BD L2 winding C CB under Q CB under Q T2 winding T2 core T1 winding CY C C L LF LF Input wire Output wire CB under U CB under Q CB under U Ambient Note(s): 1. The temperatures were measured under worst normal mode defined in and as described in sub-clause and at voltages as described above. 2. The maximum ambient temperature permitted by the manufacturer s specification is 35 C. All values for allowed Tmax ( C) are re-calculated from actual ambient respectively. temperature T of winding: t 1 ( C) R 1 ( Ω) t 2 ( C) R 2 ( Ω ) T ( C) allowed T max ( C) supplementary information: insulation class Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

41 Report No.: SA L age 41 of TABLE: Ball pressure test of thermoplastic parts allowed impression diameter (mm)... : less than or equal to 2.0 part test temperature ( C) impression diameter (mm) supplementary information: -- Bobbin material of transformer T1 is made of henolic materials, no other parts necessary to test. 4.7 TABLE: resistance to fire part manufacturer of material type of material thickness (mm) flammability class Evidence supplementary information: See critical component list for details. 5.1 TABLE: touch current measurement Measured between: Measured (ma) Limit (ma) Comments/Conditions L/N Output terminal To output terminal L/N plastic enclosure To accessible plastic part (with metal foil) supplementary information: -- Supplied with 264Vac/60Hz Overall capacitor:. CY6=CY7=2200pF 5.2 TABLE: Electric strength tests, impulse tests and voltage surge tests Test voltage applied between: Voltage shape (AC, DC, impulse, surge) Test voltage (V) Breakdown Yes / No Line & neutral and Enclosure(plastic) for unit AC 3000 No Line & neutral and output for unit AC 3000 No T1: primary and secondary AC 3000 No T1: secondary and core AC 3000 No One layer insulation type wrapped around T1 AC 3000 No Note(s): 5.3 TABLE: Fault condition tests Ambient temperature ( C)... : -- Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

42 Report No.: SA L age 42 of 45 Component No. For model: XT-2400G ower source for EUT: ManuFacturer, model/type, output rating... : Fault Supply voltage (V) Test time Fuse # Fuse current (A) BD1 s-c 240 1s F to 0A C17 s-c 240 1s F to 0A Q2 in G to D Q2 in D to S Q2 in G to S T2 in 1 to 2 T2 in 3 to 4 T2 in A to B T2 in A to C T2 in B to C T1 in 1 to 2 T1 in 3 to 4 T1 in A to B U4 in 1 to 2 U4 in 3 to 4 s-c 240 1s F to 0A s-c 240 1s F to 0A s-c mins F to 0.06A s-c mins F to 0.06A s-c mins F to 0.06A s-c mins F to 0.06A s-c mins F to 0.06A s-c mins F to 0.06A s-c mins F to 0.06A s-c mins F to 0.06A s-c mins F to 0.06A s-c mins F to 0.06A s-c mins F to 0.06A U4 in 1 o-c mins F to 0.06A U5 in 1 to 2 U5 in 3 to 4 s-c mins F to 0.06A s-c mins F to 0.06A U5 in 1 o-c mins F to 0.06A -- Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com Observation F3 opened, NB/NT/NC, no hazards. F3 opened, NB/NT/NC, no hazards. F3 opened,q1 damage, NB/NT/NC, no hazards. F3 opened,q1 damage, NB/NT/NC, no hazards. Unit shut down, NB/NC, no hazards. Unit shut down, NB/NC, no hazards. Unit shut down, NB/NC, no hazards. Unit shut down, NB/NC, no hazards. Unit shut down, NB/NC, no hazards. Unit shut down, NB/NC, no hazards. Unit shut down, NB/NC, no hazards. Unit shut down, NB/NC, no hazards. Unit shut down, NB/NC, no hazards. Unit shut down, NB/NC, no hazards. Unit shut down, NB/NC, no hazards. Unit shut down, NB/NC, no hazards. Unit shut down, NB/NC, no hazards. Unit shut down, NB/NC, no hazards. Unit shut down, NB/NC, no hazards.

43 Report No.: SA L age 43 of 45 Q4 in D to S s-c mins F to 0.06A Output s-c mins F to 0.06A Output o-l 240 Transformer o-l 240 Blocked ventilation openings Blocked the fans b-v 240 b-v 240 4hrs22min s 4hrs36min s 1hrs30min s 1hrs36min s F3 F to to to 0.04A to to to 0.04A F F Unit shut down, NB/NC, no hazards. Unit shut down, NB/NC, no hazards. Overload to 5.66A, NB/NT/NC, unit shut down, no hazards. Maximum temperature were measured: T1 winding: 56.3 C T1 core: 53.2 C U4: 46.3 C U5:45.6 C Ambient: 25.3 C Overload to 5.68A, NB/NT/NC, unit shut down, no hazards. Maximum temperature were measured: T1 winding:58.4 C T1 core: 55.7 C U4: 47.4 C U5:46.1 C Ambient: 25.5 C Maximum temperature were measured: T1 winding: 48.2 C T1 core: 45.6 C U4: 42.4 C U5:41.3 C Ambient: 25.3 C Maximum temperature were measured: T1 winding: 49.6 C T1 core: 46.2 C U4: 42.9 C U5:42.2 C Ambient: 25.4 C Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

44 Report No.: SA L age 44 of 45 Notes: The unit passed 3000V hi-pot test between primary and accessible output connector after single fault test above. 1. In fault column, s-c=short-circuited, o-l=over-loaded. 2. For transformer winding overload, each winding was individually loaded after the rectifier. 3. Each fault where R1 opened was repeated 1 times with each fuse source and with same result. 4. Transformer winding and core temperature limit is 155 C (175-10)-(35-25), test where components damaged, the test repeated three times with the same result. 5. -Results Key: I = Internal protection operated (component indicated) CT = Constant temperatures were obtained TW = Transformer winding opened CD = Components damaged (damaged components indicated) NB = No indication of dielectric breakdown YB= Dielectric breakdown (time and location indicated) NC = Cheesecloth remained intact YC = Cheesecloth charred or flamed NT = Tissue paper remained intact YT = Tissue paper charred or flamed. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

45 Report No.: SA L age 45 of 45 C.2 TABLE: transformers Loc. Tested insulation Working voltage peak / V Transform er T1:rimar y winding to secondar y winding Transform er T1: core to primary winding Transform er T1: core to secondar y winding Transform er T2:rimar y winding to secondar y winding Transform er T2: core to primary winding Transform er T2: core to secondar y winding Loc. Transform er T1:rimar y winding to secondar y winding Reinforced insulation Basic insulation Basic insulation Reinforced insulation Basic insulation Basic insulation Reinforced insulation (2.10.2) Tested insulation Working voltage rms / V (2.10.2) Required electric strength Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com (5.2) 3000Va c 3000Va c 3000Va c 3000Va c 3000Va c 3000Va c Test voltage/ V 3000Va c Required clearance / mm (2.10.3) Required creepage distance / mm (2.10.4) Required distance thr. insul. (2.10.5) * * * * * * Measured clearance / mm Measured creepage dist./ mm Measured distance thr. insul. / mm; number of layers 2 layer insulation type

46 Report No.: SA L age 46 of 45 Transform er T1: core to Basic insulation primary winding Transform er T1: core to Basic insulation secondar y winding Transform er T2:rimar y winding Reinforced insulation to secondar y winding Transform er T2: core to Basic insulation primary winding Transform er T2: core to Basic insulation secondar y winding Supplementary information: 3000Va c 3000Va c 3000Va c 3000Va c 3000Va c layer insulation type Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

47 Attachment 1 Report No.: SA L age 1 of 19 National Differences Clause Requirement + Test Result Remark Verdict ATTACHMENT TO TEST REORT IEC EUROEAN GROU DIFFERENCES AND NATIONAL DIFFERENCES Information technology equipment Safety Differences according to... : Attachment Form No.... : Attachment Originator... : ART 1: GENERAL REQUIREMENTS EN :2006/A11:2009/A1:2010/A12:2011/A2:2013 EU_GD_IEC60950_1F SGS Fimko Ltd Master Attachment... : Date Copyright 2014 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE), Geneva, Switzerland. All rights reserved. EN :2006/A11:2009/A1:2010/A12:2011/A2:2013 CENELEC COMMON MODIFICATIONS IEC , GROU DIFFERENCES (CENELEC common modifications EN) Clause Requirement + Test Result - Remark Verdict Contents (A2:2013) Clauses, subclauses, notes, tables and figures which are additional to those in IEC and it s amendmets are prefixed Z Add the following annexes: Annex ZA (normative) Annex ZB (normative) Annex ZD (informative) Normative references to international publications with their corresponding European publications Special national conditions IEC and CENELEC code designations for flexible cords General Delete all the country notes in the reference document (IEC :2005) according to the following list: Note Note 2 & Note Note Note Note 4, 5 & Note Note Note Note Note Note 2 & Note Note Note Note Note Note Note 1 & Note Note Note Note 3 & Note 1 6 Note 2 & Note Note Note Note Note 7.1 Note Note 7.3 Note 1 & 2 G.2.1 Note 2 Annex H Note 2 General (A1:2010) Delete all the country notes in the reference document (IEC :2005/A1:2010) according to the following list: Note Note Note 2 EE.3 Note Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

48 Attachment 1 Report No.: SA L age 2 of 19 National Differences Clause Requirement + Test Result Remark Verdict General (A2:2013) (A1:2010) 1.3.Z1 (A12:2011) (Added info*) (A1:2010) (A ) Delete all the country notes in the reference document (IEC :2005/A2:2013) according to the following list: Note * Note Note * Note of secretary: Text of Common Modification remains unchanged. Replace the text of NOTE 3 by the following. NOTE 3 The requirements of EN may also be used to meet safety requirements for multimedia equipment. See IEC Guide 112, Guide on the safety of multimedia equipment. For television sets EN applies. Add the following subclause: Not such equipment. 1.3.Z1 Exposure to excessive sound pressure The apparatus shall be so designed and constructed as to present no danger when used for its intended purpose, either in normal operating conditions or under fault conditions, particularly providing protection against exposure to excessive sound pressures from headphones or earphones. NOTE Z1 A new method of measurement is described in EN , Sound system equipment: Headphones and earphones associated with portable audio equipment - Maximum sound pressure level measurement methodology and limit considerations - art 1: General method for one package equipment, and in EN , Sound system equipment: Headphones and earphones associated with portable audio equipment - Maximum sound pressure level measurement methodology and limit considerations - art 2: Guidelines to associate sets with headphones coming from different manufacturers. In EN :2006/A12:2011 Deleted. Delete the addition of 1.3.Z1 / EN :2006 Delete the definition Z1 / EN :2006 /A1:2010 Add the following NOTE: NOTE Z1 The use of certain substances in electrical and electronic equipment is restricted within the EU: see Directive 2002/95/EC. New Directive 2011/65/11 * In addition, for a ORTABLE SOUND SYSTEM, the instructions shall include a warning that excessive sound pressure from earphones and headphones can cause hearing loss. In EN :2006/A12:2011 Delete NOTE Z1 and the addition for ortable Sound System. Add the following clause and annex to the existing standard and amendments. Added. Added. Replaced. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

49 Attachment 1 Report No.: SA L age 3 of 19 National Differences Clause Requirement + Test Result Remark Verdict Zx rotection against excessive sound pressure from personal music players Zx.1 General This sub-clause specifies requirements for protection against excessive sound pressure from personal music players that are closely coupled to the ear. It also specifies requirements for earphones and headphones intended for use with personal music players. Not such equipment. A personal music player is a portable equipment for personal use, that: -is designed to allow the user to listen to recorded or broadcast sound or video; and -primarily uses headphones or earphones that can be worn in or on or around the ears; and -allows the user to walk around while in use. NOTE 1 Examples are hand-held or body-worn portable CD players, M3 audio players, mobile phones with M3 type features, DA s or similar equipment. A personal music player and earphones or headphones intended to be used with personal music players shall comply with the requirements of this sub-clause. The requirements in this sub-clause are valid for music or video mode only. The requirements do not apply: -while the personal music player is connected to an external amplifier; or -while the headphones or earphones are not used. NOTE 2 An external amplifier is an amplifier which is not part of the personal music player or the listening device, but which is intended to play the music as a standalone music player. The requirements do not apply to: -hearing aid equipment and professional equipment; NOTE 3 rofessional equipment is equipment sold through special sales channels. All products sold through normal electronics stores are considered not to be professional equipment. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

50 Attachment 1 Report No.: SA L age 4 of 19 National Differences Clause Requirement + Test Result Remark Verdict -analogue personal music players (personal music players without any kind of digital processing of the sound signal) that are brought to the market before the end of NOTE 4 This exemption has been allowed because this technology is falling out of use and it is expected that within a few years it will no longer exist. This exemption will not be extended to other technologies. For equipment which is clearly designed or intended for use by young children, the limits of EN 71-1 apply. Zx.2 Equipment requirements No safety provision is required for equipment that complies with the following: -equipment provided as a package (personal music player with its listening device), where the acoustic output LAeq,T is 85 dba measured while playing the fixed programme simulation noise as described in EN ; and -a personal music player provided with an analogue electrical output socket for a listening device, where the electrical output is 27 mv measured as described in EN , while playing the fixed programme simulation noise as described in EN NOTE 1 Wherever the term acoustic output is used in this clause, the 30 s A-weighted equivalent sound pressure level LAeq,T is meant. See also Zx.5 and Annex Zx. All other equipment shall: a) protect the user from unintentional acoustic outputs exceeding those mentioned above; and b) have a standard acoustic output level not exceeding those mentioned above, and automatically return to an output level not exceeding those mentioned above when the power is switched off; and Not such equipment. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

51 Attachment 1 Report No.: SA L age 5 of 19 National Differences Clause Requirement + Test Result Remark Verdict c) provide a means to actively inform the user of the increased sound pressure when the equipment is operated with an acoustic output exceeding those mentioned above. Any means used shall be acknowledged by the user before activating a mode of operation which allows for an acoustic output exceeding those mentioned above. The acknowledgement does not need to be repeated more than once every 20 h of cumulative listening time; and NOTE 2 Examples of means include visual or audible signals. Action from the user is always required. NOTE 3 The 20 h listening time is the accumulative listening time, independent how often and how long the personal music player has been switched off. d) have a warning as specified in Zx.3; and e) not exceed the following: 1) equipment provided as a package (player with Its listening device), the acoustic output shall be 100 dba measured while playing the fixed programme simulation noise described in EN ; and 2) a personal music player provided with an analogue electrical output socket for a listening device, the electrical output shall be 150 mv measured as described in EN , while playing the fixed programme simulation noise described in EN For music where the average sound pressure (long term LAeq,T) measured over the duration of the song is lower than the average produced by the programme simulation noise, the warning does not need to be given as long as the average sound pressure of the song is below the basic limit of 85 dba. In this case T becomes the duration of the song. NOTE 4 Classical music typically has an average sound pressure (long term LAeq,T) which is much lower than the average programme simulation noise. Therefore, if the player is capable to analyse the song and compare it with the programme simulation noise, the warning does not need to be given as long as the average sound pressure of the song is below the basic limit of 85 dba. For example, if the player is set with the programme simulation noise to 85 dba, but the average music level of the song is only 65 dba, there is no need to give a warning or ask an acknowledgement as long as the average sound level of the song is not above the basic limit of 85 dba. Not such equipment. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

52 Attachment 1 Report No.: SA L age 6 of 19 National Differences Clause Requirement + Test Result Remark Verdict Zx.3 Warning The warning shall be placed on the equipment, or on the packaging, or in the instruction manual and shall consist of the following: -the symbol of Figure 1 with a minimum height of 5 mm; and -the following wording, or similar: To prevent possible hearing damage, do not listen at high volume levels for long periods. Not such equipment. Figure 1 Warning label (IEC ) Alternatively, the entire warning may be given through the equipment display during use, when the user is asked to acknowledge activation of the higher level. Zx.4 Requirements for listening devices (headphones and earphones) Zx.4.1 Wired listening devices with analogue Not such equipment. input With 94 dba sound pressure output LAeq,T, the input voltage of the fixed programme simulation noise described in EN shall be 75 mv. This requirement is applicable in any mode where the headphones can operate (active or passive), including any available setting (for example built-in volume level control). NOTE The values of 94 dba 75 mv correspond with 85dBA 27 mv and 100 dba 150 mv. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

53 Attachment 1 Report No.: SA L age 7 of 19 National Differences Clause Requirement + Test Result Remark Verdict Zx.4.2 Wired listening devices with digital input With any playing device playing the fixed programme simulation noise described in EN (and respecting the digital interface standards, where a digital interface standard exists that specifies the equivalent acoustic level), the acoustic output LAeq,T of the listening device shall be 100 dba. This requirement is applicable in any mode where the headphones can operate, including any available setting (for example built-in volume level control, additional sound feature like equalization, etc.). NOTE An example of a wired listening device with digital input is a USB headphone. Zx.4.3 Wireless listening devices In wireless mode: -with any playing and transmitting device playing the fixed programme simulation noise described in EN ; and -respecting the wireless transmission standards, where an air interface standard exists that specifies the equivalent acoustic level; and -with volume and sound settings in the listening device (for example built-in volume level control, additional sound feature like equalization, etc.) set to the combination of positions that maximize the measured acoustic output for the abovementioned programme simulation noise, the acoustic output LAeq,T of the listening device shall be 100 dba. NOTE An example of a wireless listening device is a Bluetooth headphone. Zx.5 Measurement methods Measurements shall be made in accordance with EN or EN as applicable. Unless stated otherwise, the time interval T shall be 30 s. NOTE Test method for wireless equipment provided without listening device should be defined. Not such equipment. Not such equipment. Not such equipment. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

54 Attachment 1 Report No.: SA L age 8 of 19 National Differences Clause Requirement + Test Result Remark Verdict Replace the subclause as follows: Basic requirements To protect against excessive current, shortcircuits and earth faults in RIMARY CIRCUITS, protective devices shall be included either as integral parts of the equipment or as parts of the building installation, subject to the following, a), b) and c): a) except as detailed in b) and c), protective devices necessary to comply with the requirements of 5.3 shall be included as parts of the equipment; b) for components in series with the mains input to the equipment such as the supply cord, appliance coupler, r.f.i. filter and switch, shortcircuit and earth fault protection may be provided by protective devices in the building installation; Replaced. c) it is permitted for LUGGABLE EQUIMENT TYE B or ERMANENTLY CONNECTED EQUIMENT, to rely on dedicated overcurrent and short-circuit protection in the building installation, provided that the means of protection, e.g. fuses or circuit breakers, is fully specified in the installation instructions. If reliance is placed on protection in the building installation, the installation instructions shall so state, except that for LUGGABLE EQUIMENT TYE A the building installation shall be regarded as providing protection in accordance with the rating of the wall socket outlet This subclause has been declared void Delete the NOTE in Table 3A, and delete also in this table the conduit sizes in parentheses. Deleted. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

55 Attachment 1 Report No.: SA L age 9 of 19 National Differences Clause Requirement + Test Result Remark Verdict Replace IEC 53 by H05 RR-F ; IEC 52 by H03 VV-F or H03 VVH2-F ; IEC 53 by H05 VV-F or H05 VVH2-F2. In Table 3B, replace the first four lines by the following: Up to and including 6 0,75 a) Over 6 up to and including 10 (0,75) b) 1,0 Over 10 up to and including 16 (1,0) c) 1,5 In the conditions applicable to Table 3B delete the words in some countries in condition a). In NOTE 1, applicable to Table 3B, delete the second sentence In Table 3D, delete the fourth line: conductor sizes for 10 to 13 A, and replace with the following: Over 10 up to and including 16 1,5 to 2,5 1,5 to 4 Replaced. Deleted. Delete the fifth line: conductor sizes for 13 to 16 A (A1:2010) Replace the existing NOTE by the following: NOTE Z1 Attention is drawn to: 1999/519/EC: Council Recommendation on the limitation of exposure of the general public to electromagnetic fields 0 Hz to 300 GHz, and 2006/25/EC: Directive on the minimum health and safety requirements regarding the exposure of workers to risks arising from physical agents (artifical optical radiation). Added. Standards taking into account mentioned Recommendation and Directive which demonstrate compliance with the applicable EU Directive are indicated in the OJEC. Annex H Replace the last paragraph of this annex by: At any point 10 cm from the surface of the OERATOR ACCESS AREA, the dose rate shall not exceed 1 μsv/h (0,1 mr/h) (see NOTE). Account is taken of the background level. Replace the notes as follows: NOTE These values appear in Directive 96/29/Euratom. Delete NOTE 2. Replaced. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

56 Attachment 1 Report No.: SA L age 10 of 19 National Differences Clause Requirement + Test Result Remark Verdict Bibliograph y ZA Additional EN standards. NORMATIVE REFERENCES TO INTERNATIONAL UBLICATIONS WITH THEIR CORRESONDING EUROEAN UBLICATIONS ZB ANNEX (normative) SECIAL NATIONAL CONDITIONS (EN) Clause Requirement + Test Result - Remark Verdict In Denmark, certain types of Class I appliances (see ) may be provided with a plug not Class II equipment. establishing earthing conditions when inserted into Danish socket-outlets In Norway and Sweden, for requirements see (A11:2009) and 7.3 of this annex (A11:2009) In Finland, Norway and Sweden, resistors bridging BASIC INSULATION in CLASS I LUGGABLE EQUIMENT TYE A must comply with the requirements in In addition when a single resistor is used, the resistor must withstand the resistor test in In Norway, due to the IT power system used (see annex V, Figure V.7), capacitors are required to be rated for the applicable line-to-line voltage (230 V) In Finland, Norway and Sweden, the third dashed sentence is applicable only to equipment as defined in of this annex. No such construction. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

57 Attachment 1 Report No.: SA L age 11 of 19 National Differences Clause Requirement + Test Result Remark Verdict In Finland, Norway and Sweden, CLASS I LUGGABLE EQUIMENT TYE A intended for connection to other equipment or a network shall, if safety relies on connection to protective earth or if surge suppressors are connected between the network terminals and accessible parts, have a marking stating that the equipment must be connected to an earthed mains socket-outlet. The marking text in the applicable countries shall be as follows: In Finland: "Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan" In Norway: Apparatet må tilkoples jordet stikkontakt In Sweden: Apparaten skall anslutas till jordat uttag In Norway and Sweden, the screen of the cable distribution system is normally not earthed at the entrance of the building and there is normally no equipotential bonding system within the building. Therefore the protective earthing of the building installation need to be isolated from the screen of a cable distribution system. It is however accepted to provide the insulation external to the equipment by an adapter or an interconnection cable with galvanic isolator, which may be provided by e.g. a retailer. The user manual shall then have the following or similar information in Norwegian and Swedish language respectively, depending on in what country the equipment is intended to be used in: Equipment connected to the protective earthing of the building installation through the mains connection or through other equipment with a connection to protective earthing and to a cable distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection to a cable distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator, see EN ). Class II equipment (A11:2009) Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

58 Attachment 1 Report No.: SA L age 12 of 19 National Differences Clause Requirement + Test Result Remark Verdict NOTE In Norway, due to regulation for installations of cable distribution systems, and in Sweden, a galvanic isolator shall provide electrical insulation below 5 MHz. The insulation shall withstand a dielectric strength of 1,5 kv r.m.s., 50 Hz or 60 Hz, for 1 min (A2:2013) (A11:2009) Translation to Norwegian (the Swedish text will also be accepted in Norway): Utstyr som er koplet til beskyttelsesjord via nettplugg og/eller via annet jordtilkoplet utstyr og er tilkoplet et kabel-tv nett, kan forårsake brannfare. For å unngå dette skal det ved tilkopling av utstyret til kabel-tv nettet installeres en galvanisk isolator mellom utstyret og kabel- TV nettet. Translation to Swedish: Utrustning som är kopplad till skyddsjord via jordat vägguttag och/eller via annan utrustning och samtidigt är kopplad till kabel-tv nät kan i vissa fall medfőra risk főr brand. Főr att undvika detta skall vid anslutning av utrustningen till kabel-tv nät galvanisk isolator finnas mellan utrustningen och kabel-tv nätet. In Denmark, CLASS I LUGGABLE EQUIMENT TYE A intended for connection to other equipment or a network shall, if safety relies on connection to protective earth or if surge suppressors are connected between the network terminals and accessible parts, have a marking stating that the equipment must be connected to an earthed mains socket-outlet. The marking text in Denmark shall be as follows: In Denmark: Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord. In Denmark, socket-outlets for providing power to other equipment shall be in accordance with the Heavy Current Regulations, Section D1, Standard Sheet DK 1-3a, DK 1-5a or DK 1-7a, when used on Class I equipment. For STATIONARY EQUIMENT the socket-outlet shall be in accordance with Standard Sheet DK 1-1b or DK 1-5a. For CLASS II EQUIMENT the socket outlet shall be in accordance with Standard Sheet DKA 1-4a. No socket-outlet provided. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

59 Attachment 1 Report No.: SA L age 13 of 19 National Differences Clause Requirement + Test Result Remark Verdict (A2:2013) In Denmark, socket-outlets for providing power to other equipment shall be in accordance with the DS D1:2011. For class I equipment the following Standard Sheets are applicable: DK 1-3a, DK 1-1c, DK 1-1d, DK 1-5a or DK 1-7a, with the exception for STATIONARY EQUIMENT where the socket-outlets shall be in accordance with Standard Sheet DK 1-1b, DK 1-1c, DK 1-1d or DK 1-5a. Socket outlets intended for providing power to Class II apparatus with a rated current of 2,5 A shall be in accordance with DS D1 standard sheet DKA 1-4a. Other current rating socket outlets shall be in compliance with by DS D1 Standard Sheet DKA 1-3a or DKA 1-3b. Justification the Heavy Current Regulations, 6c In Norway, for requirements see , and of this annex In Finland, Norway and Sweden there are additional requirements for the insulation. See and of this annex In Norway, for requirements see , and of this annex In the United Kingdom, the current rating of the circuit shall be taken as 13 A, not 16 A. No TNV. No TNV. No TNV In the United Kingdom, to protect against excessive currents and short-circuits in the RIMARY CIRCUIT of DIRECT LUG-IN EQUIMENT, tests according to 5.3 shall be conducted, using an external protective device rated 30 A or 32 A. If these tests fail, suitable protective devices shall be included as integral parts of the DIRECT LUG-IN EQUIMENT, so that the requirements of 5.3 are met In Finland, Norway and Sweden, there are additional requirements for the insulation, see and of this annex. Model with UK plug not applied for. No TNV. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

60 Attachment 1 Report No.: SA L age 14 of 19 National Differences Clause Requirement + Test Result Remark Verdict In Switzerland, supply cords of equipment having a RATED CURRENT not exceeding 10 A shall be provided with a plug complying with SEV 1011 or IEC and one of the following dimension sheets: SEV lug Type 15 3+N+E 250/400 V, 10 A SEV lug Type V, 10 A L+N SEV lug Type 12 L+N+E 250 V, 10 A In general, EN applies for plugs for currents exceeding 10 A. However, a 16 A plug and socket-outlet system is being introduced in Switzerland, the plugs of which are according to the following dimension sheets, published in February 1998: SEV : lug Type 25, 3L+N+E 230/400 V, 16 A SEV :lug Type 21, L+N, 250 V, 16A SEV : lug Type 23, L+N+E 250 V, In Denmark, supply cords of single-phase equipment having a rated current not exceeding13 A shall be provided with a plug according to the Heavy Current Regulations, Section D1. CLASS I EQUIMENT provided with socketoutlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules shall be provided with a plug in accordance with standard sheet DK 2-1a or DK 2-5a. If poly-phase equipment and single-phase equipment having a RATED CURRENT exceeding 13 A is provided with a supply cord with a plug, this plug shall be in accordance with the Heavy Current Regulations, Section D1 or EN Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

61 Attachment 1 Report No.: SA L age 15 of 19 National Differences Clause Requirement + Test Result Remark Verdict In Denmark, supply cords of single-phase (A2:2013) equipment having a rated current not exceeding 13 A shall be provided with a plug according to DS D1. CLASS I EQUIMENT provided with socketoutlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules shall be provided with a plug in accordance with standard sheet DK 2-1a or DK 2-5a. If a single-phase equipment having a RATED CURRENT exceeding 13 A or if a poly-phase equipment is provided with a supply cord with a plug, this plug shall be in accordance with the standard sheets DK 6-1a in DS D1 or EN Justification the Heavy Current Regulations, 6c In Spain, supply cords of single-phase equipment having a rated current not exceeding 10 A shall be provided with a plug according to UNE 20315:1994. Supply cords of single-phase equipment having a rated current not exceeding 2,5 A shall be provided with a plug according to UNE-EN 50075:1993. CLASS I EQUIMENT provided with socketoutlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules, shall be provided with a plug in accordance with standard UNE 20315:1994. If poly-phase equipment is provided with a supply cord with a plug, this plug shall be in accordance with UNE-EN In the United Kingdom, apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to BS 1363 by means of that flexible cable or cord and plug, shall be fitted with a standard plug in accordance with Statutory Instrument 1768: The lugs and Sockets etc. (Safety) Regulations 1994, unless exempted by those regulations. NOTE Standard plug is defined in SI 1768:1994 and essentially means an approved plug conforming to BS 1363 or an approved conversion plug. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

62 Attachment 1 Report No.: SA L age 16 of 19 National Differences Clause Requirement + Test Result Remark Verdict In Ireland, apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to I.S. 411 by means of that flexible cable or cord and plug, shall be fitted with a 13 A plug in accordance with Statutory Instrument 525: National Standards Authority of Ireland (section 28) (13 A lugs and Conversion Adaptors for Domestic Use) Regulations In Switzerland, for requirements see of this annex In the United Kingdom, a power supply cord with conductor of 1,25 mm2 is allowed for equipment with a rated current over 10 A and up to and including 13 A In the United Kingdom, the range of conductor sizes of flexible cords to be accepted by terminals for equipment with a RATED CURRENT of over 10 A up to and including 13 A is: 1,25 mm 2 to 1,5 mm 2 nominal cross-sectional area In the United Kingdom, the torque test is performed using a socket outlet complying with BS 1363 part 1:1995, including Amendment 1:1997 and Amendment 2:2003 and the plug part of DIRECT LUG-IN EQUIMENT shall be assessed to BS 1363: art 1, 12.1, 12.2, 12.3, 12.9, 12.11, 12.12, 12.13, and 12.17, except that the test of is performed at not less than 125 C. Where the metal earth pin is replaced by an Insulated Shutter Opening Device (ISOD), the requirements of clauses 22.2 and 23 also apply In Ireland, DIRECT LUG-IN EQUIMENT is known as plug similar devices. Such devices shall comply with Statutory Instrument 526: National Standards Authority of Ireland (Section 28) (Electrical plugs, plug similar devices and sockets for domestic use) Regulations, Not applied for Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

63 Attachment 1 Report No.: SA L age 17 of 19 National Differences Clause Requirement + Test Result Remark Verdict In Finland, Norway and Sweden TOUCH CURRENT measurement results exceeding 3,5 ma r.m.s. are permitted only for the following equipment: STATIONARY LUGGABLE EQUIMENT TYE A that is intended to be used in a RESTRICTED ACCESS LOCATION where equipotential bonding has been applied, for example, in a telecommunication centre; and has provision for a permanently connected ROTECTIVE EARTHING CONDUCTOR; and is provided with instructions for the installation of that conductor by a SERVICE ERSON; STATIONARY LUGGABLE EQUIMENT TYE B; STATIONARY ERMANENTLY CONNECTED EQUIMENT (A1:2010) In Finland, Norway and Sweden, add the following text between the first and second paragraph of the compliance clause: If this insulation is solid, including insulation forming part of a component, it shall at least consist of either - two layers of thin sheet material, each of which shall pass the electric strength test below, or - one layer having a distance through insulation of at least 0,4 mm, which shall pass the electric strength test below. Alternatively for components, there is no distance through insulation requirements for the insulation consisting of an insulating compound completely filling the casing, so that CLEARANCES and CREEAGE DISTANCES do not exist, if the component passes the electric strength test in accordance with the compliance clause below and in addition - passes the tests and inspection criteria of with an electric strength test of 1,5 kv multiplied by 1,6 (the electric strength test of shall be performed using 1,5 kv), and - is subject to ROUTINE TESTING for electric strength during manufacturing, using a test voltage of 1,5 kv. Not exceed 3.5mA. No TNV. Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

64 Attachment 1 Report No.: SA L age 18 of 19 National Differences Clause Requirement + Test Result Remark Verdict It is permitted to bridge this insulation with an optocoupler complying with b). It is permitted to bridge this insulation with a capacitor complying with EN :2005, subclass Y2. A capacitor classified Y3 according to EN :2005, may bridge this insulation under the following conditions: - the insulation requirements are satisfied by having a capacitor classified Y3 as defined by EN , which in addition to the Y3 testing, is tested with an impulse test of 2,5 kv defined in EN :2006, ; - the additional testing shall be performed on all the test specimens as described in EN ; - the impulse test of 2,5 kv is to be performed before the endurance test in EN , in the sequence of tests as described in EN In Finland, Norway and Sweden, the exclusions are applicable for ERMANENTLY CONNECTED EQUIMENT, LUGGABLE EQUIMENT TYE B and equipment intended to be used in a RESTRICTED ACCESS LOCATION where equipotential bonding has been applied, e.g. in a telecommunication centre, and which has provision for a permanently connected ROTECTIVE EARTHING CONDUCTOR and is provided with instructions for the installation of that conductor by a SERVICE ERSON. 7.2 In Finland, Norway and Sweden, for requirements see and of this annex. No TNV. Not connected to cable distribution system. The term TELECOMMUNICATION NETWORK in being replaced by the term CABLE DISTRIBUTION SYSTEM. 7.3 (A11:2009) In Norway and Sweden, for requirements see and of this annex. Not connected to cable distribution system. Annex ZD (informative) IEC and CENELEC code designations for flexible cords Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

65 Attachment 1 Report No.: SA L age 19 of 19 National Differences Clause Requirement + Test Result Remark Verdict Type of flexible cord Code designations IEC CENELEC VC insulated cords Flat twin tinsel cord IEC 41 H03VH-Y Light polyvinyl chloride sheathed flexible cord IEC 52 H03VV-F H03VVH2-F Ordinary polyvinyl chloride sheathed flexible cord IEC 53 H05VV-F H05VVH2-F Rubber insulated cords Braided cord IEC 51 H03RT-F Ordinary tough rubber sheathed flexible cord IEC 53 H05RR-F Ordinary polychloroprene sheathed flexible cord IEC 57 H05RN-F Heavy polychloroprene sheathed flexible cord IEC 66 H07RN-F Cords having high flexibility Rubber insulated and sheathed cord IEC 86 H03RR-H Rubber insulated, crosslinked VC sheathed cord IEC 87 H03RV4-H Crosslinked VC insulated and sheathed cord IEC 88 H03V4V4-H Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

66 Attachment 2 Report No.: SA L age 1 of 6 Figure 1. Overall view of unit Figure 2. Overall view of unit Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

67 Attachment 2 Report No.: SA L age 2 of 6 Figure 3. Inside view of unit Figure 4. Inside view of unit Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

68 Attachment 2 Report No.: SA L age 3 of 6 Figure 5. Inside view of unit Figure 6. Top view of CB Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

69 Attachment 2 Report No.: SA L age 4 of 6 Figure 7. Bottom view of CB Figure 8. Top view of transformer(t1) Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

70 Attachment 2 Report No.: SA L age 5 of 6 Figure 9. Bottom view of transformer (T1) Figure 10. Top view of transformer(t2) Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com

71 Attachment 2 Report No.: SA L age 6 of 6 Figure 11. Bottom view of transformer(t2) Dongguan City, Guangdong r., China. hone: ; Fax: anci@anci.com