Shenzhen BST Technology Co., Ltd. Report No.: BST Y-1SR-2 XIAMEN RGBLINK SCIENCE & TECHNOLOGY CO., LTD. TEST REPORT

Transcription

1 Report o.: BST Y-1SR-2 XIAME RGBLIK SCIECE & TECHOLOGY CO., LTD. TEST REORT repared For: XIAME RGBLIK SCIECE & TECHOLOGY CO., LTD. S Weiye building Torch Hi-Tech Industrial Development Zone roduct ame: MULTI-FORMAT VIDEO SWITCHER Trade ame: Main Test Model: Additional Model: repared By: C 3072RO VEUS X1, VEUS X1pro, VS 168S, VS 168HD, VS 168, VS 628pro, VS 628RO II, VEUS X2, VEUS X3 Shenzhen BST Technology Co., Ltd. Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou, anshan District, Shenzhen, Guangdong, China Test Date: Mar. 20, Apr. 05, 2017 Date of Report: Apr. 06, 2017 Report o.: BST Y-1SR-2 Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 1 of 57

2 Report o.: BST Y-1SR-2 TEST Report Information technology equipment - Safety - art 1: General requirements Testing laboratory.. : Shenzhen BST Technology Co., Ltd. Address.. : Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou, anshan District, Shenzhen, Guangdong, China Testing location.. : Shenzhen BST Technology Co., Ltd. Applicant : XIAME RGBLIK SCIECE & TECHOLOGY CO., LTD. Address.. : S Weiye building Torch Hi-Tech Industrial Development Zone Standard. : :2005+AMD1:2009+AMD2:2013 rocedure deviation : /A. on-standard test method Type of test object.. : /A. : MULTI-FORMAT VIDEO SWITCHER Trademark. : Model/type reference.. : See page 1 Rating. : V~, 50/60Hz, 8.4A, 150W Manufacturer. : XIAME RGBLIK SCIECE & TECHOLOGY CO., LTD. Address.. : Test item particulars : S Weiye building Torch Hi-Tech Industrial Development Zone Equipment mobility : Movable equipment Operation condition : Continuous Class of equipment : Class I rotection against ingress of water. : /A. ossible test case verdicts : test case does not apply to the test object.. : test object does meet the requirement. : (.A.) (ass) test object does not meet the requirement. : F(ail) Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 2 of 57

3 Report o.: BST Y-1SR-2 General remarks: "(see remark #)" refers to a remark appended to the Attached with: report. "(see appended table)" refers to a table appended to A. photo documentation the report. Throughout this report a comma is used as the decimal separator. The test results presented in this report relate only to the object tested. This report shall not be reproduced except in full without the written approval of the testing laboratory. General product information: The series products have the same circuit diagram, CB layout and functionality. The differences are the model name, so, we select C 3072RO to test. Artwork of Marking Label MULTI-FORMAT VIDEO SWITCHER Model: C 3072RO Rating: V~, 50/60Hz, 8.4A, 150W XIAME RGBLIK SCIECE & TECHOLOGY CO., LTD. repared by : Engineer Reviewer : Supervisor Approved & Authorized Signer : Manager Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 3 of 57

4 Report o.: BST Y-1SR-2 1 GEERAL 1.5 Components General Comply with or relevant component standard Evaluation and testing of components Thermal controls Transformers Interconnecting cables Capacitors bridging insulation Resistors bridging insulation Resistors bridging functional, basic or supplementary insulation Resistors bridging double or reinforced insulation between a.c. mains and other circuits Resistors bridging double or reinforced insulation between a.c. mains and antenna or coaxial cable Components in equipment for IT power systems Surge suppressors General rotection of VDRs Bridging of functional insulation by a VDR Bridging of basic insulation by a VDR Bridging of supplementary, double or reinforced insulation by a VDR 1.6 ower interface AC power distribution systems Input current Voltage limit of hand-held equipment eutral conductor 1.7 Marking and instructions ower rating and identification markings See label ower rating marking Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 4 of 57

5 Report o.: BST Y-1SR-2 Multiple mains supply connections...: Rated voltage(s) or voltage range(s) (V)...: Symbol for nature of supply, for d.c. only...: Rated frequency or rated frequency range (Hz)...: Rated current (ma or A)...: Identification markings See label Manufacturer s name or trade-mark or identification mark...: Model identification or type reference...: Symbol for Class II equipment only...: Class I Other markings and symbols...: o other symbols Safety instructions and marking See the user manual General Disconnect devices Overcurrent protective device IT power distribution systems Operator access with a tool Ozone Short duty cycles Supply voltage adjustment...: Methods and means of adjustment; reference to installation instructions...: ower outlets on the equipment...: Fuse identification (marking, special fusing characteristics, cross-reference)...: Wiring terminals rotective earthing and bonding terminals...: Terminals for a.c. mains supply conductors Terminals for d.c. mains supply conductors Controls and indicators o such parts Identification, location and marking...: Colours...: Symbols according to IEC : o such symbols Markings using figures...: o figures are used. Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 5 of 57

6 Report o.: BST Y-1SR Isolation of multiple power sources...: Thermostats and other regulating devices...: Durability After test, the label is legible, no curling, no possible to remove marking plates easily Removable parts Replaceable batteries...: Language(s)...: Equipment for restricted access locations...: 2 ROTECTIO FROM HAZARDS 2.1 rotection from electric shock and energy hazards rotection in operator access areas o hazardous parts in operator access areas Access to energized parts Test by inspection...: Test with test finger (Figure 2A)...: Test with test pin (Figure 2B)...: Test with test probe (Figure 2C)...: Battery compartments Access to ELV wiring Working voltage (Vpeak or Vrms); minimum distance through insulation (mm) Access to hazardous voltage circuit wiring Energy hazards...: Manual controls Discharge of capacitors in equipment Measured voltage (V); time-constant (s)...: Energy hazards d.c. mains supply a) Capacitor connected to the d.c. mains supply..: b) Internal battery connected to the d.c. mains supply...: Audio amplifiers...: rotection in service access areas rotection in restricted access locations Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 6 of 57

7 Report o.: BST Y-1SR SELV circuits General requirements Voltages under normal conditions (V)...: <42.4Vp or 60V d.c Voltages under fault conditions (V)...: <42.4Vp or 60V d.c Connection of SELV circuits to other circuits...: 2.3 TV circuits Limits o TV circuits Type of TV circuits...: Separation from other circuits and from accessible parts General requirements rotection by basic insulation rotection by earthing rotection by other constructions...: Separation from hazardous voltages Insulation employed...: Connection of TV circuits to other circuits Insulation employed...: Test for operating voltages generated externally 2.4 Limited current circuits General requirements Limit values Frequency (Hz)...: Measured current (ma)...: Measured voltage (V)...: Measured circuit capacitance (nf or µf)...: Connection of limited current circuits to other circuits 2.5 Limited power sources a) Inherently limited output b) Impedance limited output Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 7 of 57

8 Report o.: BST Y-1SR-2 c) Regulating network limited output under normal operating and single fault condition d) Overcurrent protective device limited output Max. output voltage (V), max. output current (A), max. apparent power (VA)... : Current rating of overcurrent protective device (A).: Use of integrated circuit (IC) current limiters 2.6 rovisions for earthing and bonding rotective earthing Functional earthing rotective earthing and protective bonding conductors General Size of protective earthing conductors Rated current (A), cross-sectional area (mm 2 ), AWG... : 16 A Size of protective bonding conductors Rated current (A), cross-sectional area (mm 2 ), AWG... : rotective current rating (A), cross-sectional area (mm 2 ), AWG... : Resistance of earthing conductors and their terminations; resistance (Ω), voltage drop (V), test current (A), duration (min)... : 0.5Ω Colour of insulation... : Terminals General rotective earthing and bonding terminals Rated current (A), type, nominal thread diameter (mm)... : Separation of the protective earthing conductor from protective bonding conductors Integrity of protective earthing Interconnection of equipment Components in protective earthing conductors and protective bonding conductors Disconnection of protective earth Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 8 of 57

9 Report o.: BST Y-1SR arts that can be removed by an operator arts removed during servicing Corrosion resistance Screws for protective bonding Reliance on telecommunication network or cable distribution system 2.7 Overcurrent and earth fault protection in primary circuits Basic requirements Instructions when protection relies on building installation Faults not simulated in Short-circuit backup protection umber and location of protective devices... : rotection by several devices Warning to service personnel... : 2.8 Safety interlocks General principles o such part rotection requirements Inadvertent reactivation Fail-safe operation rotection against extreme hazard Moving parts Overriding Switches, relays and their related circuits Separation distances for contact gaps and their related circuits (mm)...: Overload test Endurance test Electric strength test Mechanical actuators 2.9 Electrical insulation roperties of insulating materials Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 9 of 57

10 Report o.: BST Y-1SR Humidity conditioning Humidity treatment performed for 48 h. Relative humidity (%), temperature ( C)...: 93%R.H, Grade of insulation Separation from hazardous voltages Method(s) used...: Method Clearances, creepage distances and distances through insulation General Frequency... : ollution degrees... : ollution degrees Reduced values for functional insulation Intervening unconnected conductive parts Insulation with varying dimensions Special separation requirements Insulation in circuits generating starting pulses Determination of working voltage General RMS working voltage eak working voltage Clearances General Mains transient voltages a) AC mains supply... : b) Earthed d.c. mains supplies... : c) Unearthed d.c. mains supplies... : d) Battery operation... : Clearances in primary circuits Clearances in secondary circuits Clearances in circuits having starting pulses Transients from a.c. mains supply... : Transients from d.c. mains supply... : Transients from telecommunication networks and cable distribution systems... : Measurement of transient voltage levels Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 10 of 57

11 Report o.: BST Y-1SR-2 a) Transients from a mains supply For an a.c. mains supply... : For a d.c. mains supply... : b) Transients from a telecommunication network : Creepage distances General Material group and comparative tracking index CTI tests... : Material group IIIb are assumed to be used Minimum creepage distances Solid insulation General Distances through insulation Insulating compound as solid insulation Semiconductor devices Cemented joints Thin sheet material General Separable thin sheet material umber of layers (pcs)... : on-separable thin sheet material Thin sheet material standard test procedure Electric strength test Thin sheet material alternative test procedure Electric strength test Insulation in wound components Wire in wound components Working voltage... : a) Basic insulation not under stress... : b) Basic, supplementary, reinforced insulation... : c) Compliance with Annex U... : Two wires in contact inside wound component; angle between 45 and : Wire with solvent-based enamel in wound components Electric strength test Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 11 of 57

12 Report o.: BST Y-1SR-2 Routine test Additional insulation in wound components Working voltage... : - Basic insulation not under stress... : - Supplementary, reinforced insulation... : Construction of printed boards Uncoated printed boards Coated printed boards Insulation between conductors on the same inner surface of a printed board Insulation between conductors on different layers of a printed board Distance through insulation umber of insulation layers (pcs)... : Component external terminations Tests on coated printed boards and coated components Sample preparation and preliminary inspection Thermal conditioning Electric strength test Abrasion resistance test Thermal cycling Test for ollution Degree 1 environment and insulating compound Tests for semiconductor devices and cemented joints Enclosed and sealed parts 3 WIRIG, COECTIOS AD SULY 3.1 General Current rating and overcurrent protection rotection against mechanical damage Securing of internal wiring Insulation of conductors Beads and ceramic insulators ot used Screws for electrical contact pressure Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 12 of 57

13 Report o.: BST Y-1SR Insulating materials in electrical connections Self-tapping and spaced thread screws Termination of conductors 10 pull test Sleeving on wiring 3.2 Connection to a mains supply Means of connection Connection to an a.c. mains supply Connection to a d.c. mains supply Multiple supply connections ermanently connected equipment umber of conductors, diameter of cable and conduits (mm)...: Appliance inlets ower supply cords AC power supply cords Type...: Rated current (A), cross-sectional area (mm 2 ), AWG...: 16 A DC power supply cords Cord anchorages and strain relief Mass of equipment (kg), pull ()...: Longitudinal displacement (mm)...: rotection against mechanical damage Cord guards Diameter or minor dimension D (mm); test mass (g)...: Radius of curvature of cord (mm)...: Supply wiring space 3.3 Wiring terminals for connection of external conductors Wiring terminals Connection of non-detachable power supply cords Screw terminals Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 13 of 57

14 Report o.: BST Y-1SR Conductor sizes to be connected Rated current (A), cord/cable type, cross-sectional area (mm 2 )... : Wiring terminal sizes Rated current (A), type, nominal thread diameter (mm)... : Wiring terminal design Grouping of wiring terminals Stranded wire 3.4 Disconnection from the mains supply General requirement Disconnect devices ermanently connected equipment arts which remain energized Switches in flexible cords umber of poles - single-phase and d.c. equipment umber of poles - three-phase equipment Switches as disconnect devices lugs as disconnect devices Interconnected equipment Multiple power sources 3.5 Interconnection of equipment General requirements Types of interconnection circuits...: ELV circuits as interconnection circuits Data ports for additional equipment 4 HYSICAL REQUIREMETS 4.1 Stability Angle of 10 Test force ()...: 4.2 Mechanical strength Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 14 of 57

15 Report o.: BST Y-1SR General Rack-mounted equipment Steady force test, applied to all components other than enclosure Steady force test, Steady force test, applied to outer enclosure. o energy or other hazards Impact test Fall test Swing test Drop test; height (mm)... : Stress relief test Cathode ray tubes icture tube separately certified... : High pressure lamps Wall or ceiling mounted equipment; force ()... : Rotating solid media Test to cover on the door.: 4.3 Design and construction Edges and corners Edges and corners of the enclosure are rounded Handles and manual controls; force ()...: Adjustable controls Securing of parts Connection by plugs and sockets Direct plug-in equipment Torque... : Compliance with the relevant mains plug standard... : Heating elements in earthed equipment Batteries - Overcharging of a rechargeable battery Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 15 of 57

16 Report o.: BST Y-1SR-2 - Unintentional charging of a non-rechargeable battery - Reverse charging of a rechargeable battery - Excessive discharging rate for any battery Oil and grease Dust, powders, liquids and gases Containers for liquids or gases Flammable liquids... : Quantity of liquid (l)... : Flash point ( C)... : Radiation General Ionizing radiation Measured radiation (pa/kg)... : Measured high-voltage (kv)... : Measured focus voltage (kv)... : CRT markings... : Effect of ultraviolet (UV) radiation on materials art, property, retention after test, flammability classification...: Human exposure to ultraviolet (UV) radiation...: Lasers (including laser diodes) and LEDs See below Lasers (including laser diodes) o lasers Laser class...: Light emitting diodes (LEDs) Other types...: 4.4 rotection against hazardous moving parts General rotection in operator access areas...: Household and home/office document/media shredders rotection in restricted access locations...: rotection in service access areas rotection against moving fan blades Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 16 of 57

17 Report o.: BST Y-1SR General ot considered to cause pain or injury. a).: Is considered to cause pain, not injury. b) : Considered to cause injury. c) : rotection for users Use of symbol or warning : rotection for service persons Use of symbol or warning : 4.5 Thermal requirements General Temperature tests ormal load condition per Annex L...: Temperature limits for materials Touch temperature limits Resistance to abnormal heat...: 4.6 Openings in enclosures Top and side openings Dimensions (mm)...: Bottoms of fire enclosures Construction of the bottomm, dimensions (mm)..: Doors or covers in fire enclosures Openings in transportable equipment Constructional design measures Dimensions (mm)...: Evaluation measures for larger openings Use of metallized parts Adhesives for constructional purposes Conditioning temperature ( C), time (weeks)...: 4.7 Resistance to fire Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 17 of 57

18 Report o.: BST Y-1SR Reducing the risk of ignition and spread of flame Method 1, selection and application of components wiring and materials Method 2, application of all of simulated fault condition tests Conditions for a fire enclosure arts requiring a fire enclosure arts not requiring a fire enclosure Materials General Materials for fire enclosures Materials for components and other parts outside fire enclosures Materials for components and other parts inside fire enclosures Materials for air filter assemblies Materials used in high-voltage components 5 ELECTRICAL REQUIREMETS AD SIMULATED ABORMAL CODITIOS 5.1 Touch current and protective conductor current General Configuration of equipment under test (EUT) Single connection to an a.c. mains supply Redundant multiple connections to an a.c. mains supply Simultaneous multiple connections to an a.c. mains supply Test circuit Application of measuring instrument Test procedure Test measurements Supply voltage (V)...: Measured touch current (ma)...: Max. allowed touch current (ma)...: Measured protective conductor current (ma)...: Max. allowed protective conductor current (ma)...: Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 18 of 57

19 Report o.: BST Y-1SR Equipment with touch current exceeding 3,5 ma General...: Simultaneous multiple connections to the supply Touch currents to telecommunication networks and cable distribution systems and from telecommunication networks Limitation of the touch current to a telecommunication network or to a cable distribution system Supply voltage (V)...: Measured touch current (ma)...: Max. allowed touch current (ma)...: Summation of touch currents from telecommunication networks a) EUT with earthed telecommunication ports...: b) EUT whose telecommunication ports have no reference to protective earth 5.2 Electric strength General Test procedure 5.3 Abnormal operating and fault conditions rotection against overload and abnormal operation See below Motors o motors Transformers Functional insulation...: Electromechanical components Audio amplifiers in ITE...: Simulation of faults Unattended equipment Compliance criteria for abnormal operating and fault conditions During the tests After the tests Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 19 of 57

20 Report o.: BST Y-1SR-2 6 COECTIO TO TELECOMMUICATIO ETWORKS 6.1 rotection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment rotection from hazardous voltages Separation of the telecommunication network from earth Requirements Supply voltage (V)...: Current in the test circuit (ma)...: Exclusions...: 6.2 rotection of equipment users from overvoltages on telecommunication networks Separation requirements Electric strength test procedure Impulse test Steady-state test Compliance criteria 6.3 rotection of the telecommunication wiring system from overheating Max. output current (A)...: Current limiting method...: 7 COECTIO TO CABLE DISTRIBUTIO SYSTEMS 7.1 General 7.2 rotection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment 7.3 rotection of equipment users from overvoltages on the cable distribution system 7.4 Insulation between primary circuits and cable distribution systems General Voltage surge test Impulse test Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 20 of 57

21 Report o.: BST Y-1SR-2 A AEX A, TESTS FOR RESISTACE TO HEAT AD FIRE A.1 Flammability test for fire enclosures of movable equipment having a total mass exceeding 18 kg, and of stationary equipment (see ) A.1.1 Samples...: Wall thickness (mm)...: A.1.2 Conditioning of samples; temperature ( C)...: A.1.3 Mounting of samples...: A.1.4 Test flame (see IEC ) Flame A, B, C or D...: A.1.5 Test procedure A.1.6 Compliance criteria Sample 1 burning time (s)...: Sample 2 burning time (s)...: Sample 3 burning time (s)...: A.2 Flammability test for fire enclosures of movable equipment having a total mass not exceeding 18 kg, and for material and components located inside fire enclosures (see and ) A.2.1 Samples, material...: Wall thickness (mm)...: A.2.2 Conditioning of samples; temperature ( C)...: A.2.3 Mounting of samples...: A.2.4 Test flame (see IEC ) Flame A, B or C...: A.2.5 Test procedure A.2.6 Compliance criteria Sample 1 burning time (s)...: Sample 2 burning time (s)...: Sample 3 burning time (s)...: A.2.7 Alternative test acc. to IEC , cl. 5 and 9 Sample 1 burning time (s)...: Sample 2 burning time (s)...: Sample 3 burning time (s)...: A.3 Hot flaming oil test (see 4.6.2) Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 21 of 57

22 Report o.: BST Y-1SR-2 A.3.1 Mounting of samples A.3.2 Test procedure A.3.3 Compliance criterion B AEX B, MOTOR TESTS UDER ABORMAL CODITIOS (see and 5.3.2) B.1 General requirements osition...: Manufacturer...: Type...: Rated values...: B.2 Test conditions B.3 Maximum temperatures B.4 Running overload test B.5 Locked-rotor overload test Test duration (days)...: Electric strength test: test voltage (V)...: B.6 Running overload test for d.c. motors in secondary circuits B.6.1 General B.6.2 Test procedure B.6.3 Alternative test procedure B.6.4 Electric strength test; test voltage (V)...: B.7 Locked-rotor overload test for d.c. motors in secondary circuits B.7.1 General B.7.2 Test procedure B.7.3 Alternative test procedure B.7.4 Electric strength test; test voltage (V)... : B.8 Test for motors with capacitors B.9 Test for three-phase motors B.10 Test for series motors Operating voltage (V)...: C AEX C, TRASFORMERS (see and 5.3.3) Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 22 of 57

23 Report o.: BST Y-1SR-2 osition... : T1 Manufacturer... : Type... : Rated values... : Class B Method of protection...: C.1 Overload test C.2 Insulation rotection from displacement of windings...: D AEX D, MEASURIG ISTRUMETS FOR TOUCH-CURRET TESTS (see 5.1.4) D.1 Measuring instrument D.2 Alternative measuring instrument E AEX E, TEMERATURE RISE OF A WIDIG (see ) F AEX F, MEASUREMET OF CLEARACES AD CREEAGE DISTACES (see 2.10 and Annex G) G AEX G, ALTERATIVE METHOD FOR DETERMIIG MIIMUM CLEARACES G.1 Clearances G.1.1 General G.1.2 Summary of the procedure for determining minimum clearances G.2 Determination of mains transient voltage (V) G.2.1 AC mains supply... : G.2.2 Earthed d.c. mains supplies... : G.2.3 Unearthed d.c. mains supplies... : G.2.4 Battery operation... : G.3 Determination of telecommunication network transient voltage (V)... : G.4 Determination of required withstand voltage (V) G.4.1 Mains transients and internal repetitive peaks... : G.4.2 Transients from telecommunication networks... : G.4.3 Combination of transients Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 23 of 57

24 Report o.: BST Y-1SR-2 G.4.4 Transients from cable distribution systems G.5 Measurement of transient voltages (V) a) Transients from a mains supply For an a.c. mains supply For a d.c. mains supply b) Transients from a telecommunication network G.6 Determination of minimum clearances... : H AEX H, IOIZIG RADIATIO (see ) J AEX J, TABLE OF ELECTROCHEMICAL OTETIALS (see ) Metal(s) used... : K AEX K, THERMAL COTROLS (see and 5.3.8) K.1 Making and breaking capacity K.2 Thermostat reliability; operating voltage (V)... : K.3 Thermostat endurance test; operating voltage (V)... : K.4 Temperature limiter endurance; operating voltage (V)... : K.5 Thermal cut-out reliability K.6 Stability of operation L AEX L, ORMAL LOAD CODITIOS FOR SOME TYES OF ELECTRICAL BUSIESS EQUIMET (see and 4.5.2) L.1 Typewriters L.2 Adding machines and cash registers L.3 Erasers L.4 encil sharpeners L.5 Duplicators and copy machines L.6 Motor-operated files L.7 Other business equipment M AEX M, CRITERIA FOR TELEHOE RIGIG SIGALS (see 2.3.1) M.1 Introduction Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 24 of 57

25 Report o.: BST Y-1SR-2 M.2 Method A M.3 Method B M.3.1 Ringing signal M Frequency (Hz)... : M Voltage (V)... : M Cadence; time (s), voltage (V)... : M Single fault current (ma)... : M.3.2 Tripping device and monitoring voltage... : M Conditions for use of a tripping device or a monitoring voltage M Tripping device M Monitoring voltage (V)... : AEX, IMULSE TEST GEERATORS (see , , , , 7.3.2, and Clause G.5).1 ITU-T impulse test generators.2 IEC impulse test generator AEX, ORMATIVE REFERECES Q AEX Q, Voltage dependent resistors (VDRs) (see ) a) referred climatic categories... : b) Maximum continuous voltage... : c) ulse current... : R AEX R, EXAMLES OF REQUIREMETS FOR QUALITY COTROL ROGRAMMES R.1 Minimum separation distances for unpopulated coated printed boards (see ) R.2 Reduced clearances (see ) S AEX S, ROCEDURE FOR IMULSE TESTIG (see ) S.1 Test equipment S.2 Test procedure S.3 Examples of waveforms during impulse testing Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 25 of 57

26 Report o.: BST Y-1SR-2 T AEX T, GUIDACE O ROTECTIO AGAIST IGRESS OF WATER (see 1.1.2) rotection against ingress of water U AEX U, ISULATED WIDIG WIRES FOR USE WITHOUT ITERLEAVED ISULATIO (see ) V AEX V, AC OWER DISTRIBUTIO SYSTEMS (see 1.6.1) V.1 Introduction V.2 T power distribution systems W AEX W, SUMMATIO OF TOUCH CURRETS W.1 Touch current from electronic circuits W.1.1 Floating circuits W.1.2 Earthed circuits W.2 Interconnection of several equipments W.2.1 Isolation W.2.2 Common return, isolated from earth W.2.3 Common return, connected to protective earth X AEX X, MAXIMUM HEATIG EFFECT I TRASFORMER TESTS (see clause C.1) X.1 Determination of maximum input current X.2 Overload test procedure Y AEX Y, ULTRAVIOLET LIGHT CODITIOIG TEST (see ) Y.1 Test apparatus... : Y.2 Mounting of test samples... : Y.3 Carbon-arc light-exposure apparatus... : Y.4 Xenon-arc light exposure apparatus... : Z AEX Z, OVERVOLTAGE CATEGORIES (see and Clause G.2) Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 26 of 57

27 Report o.: BST Y-1SR-2 AA AEX AA, MADREL TEST (see ) BB AEX BB, CHAGES I THE SECOD EDITIO CC AEX CC, Evaluation of integrated circuit (IC) current limiters CC.1 General CC.2 Test program 1.: CC.3 Test program 2.: DD AEX DD, Requirements for the mounting means of rack-mounted equipment DD.1 General DD.2 DD.3 Mechanical strength test, variable..: Mechanical strength test, 250, including end stops : DD.4 Compliance : EE AEX EE, Household and home/office document/media shredders EE.1 General EE.2 Markings and instructions Use of markings or symbols : Information of user instructions, maintenance and/or servicing instructions : EE.3 Inadvertent reactivation test : EE.4 Disconnection of power to hazardous moving parts: Use of markings or symbols : EE.5 rotection against hazardous moving parts Test with test finger (Figure 2A) : Test with wedge probe (Figure EE1 and EE2) : Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 27 of 57

28 Report o.: BST Y-1SR-2 ATTACHMET TO TEST REORT IEC EUROEA GROU DIFFERECES AD ATIOAL DIFFERECES Information technology equipment Safety art 1: General requirements Differences according to... : E :2006/A11:2009/A1:2010/A12:2011 Attachment Form o.... : EU_GD_IEC60950_1C_II Attachment Originator... : SGS Fimko Ltd Master Attachment... : Date Copyright 2011 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE), Geneva, Switzerland. All rights reserved. E :2006/A11:2009/A1:2010/A12:2011 CEELEC COMMO MODIFICATIOS, GROU DIFFERECES (CEELEC common modifications E) Contents Add the following annexes: Annex ZA (normative) Annex ZB (normative) ormative references to international publications with their corresponding European publications Special national conditions General Delete all the country notes in the reference document (:2005) according to the following list: ote ote 2 & ote ote ote ote 4, 5 & ote ote ote ote ote ote 2 & ote ote ote ote ote ote ote 1 & ote ote ote ote 3 & ote 1 6 ote 2 & ote ote ote ote ote 7.1 ote ote 7.3 ote 1 & 2 G.2.1 ote 2 Annex H ote 2 General (A1:2010) Delete all the country notes in the reference document (IEC :2005/A1:2010) according to the following list: ote ote ote 2 EE.3 ote Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 28 of 57

29 Report o.: BST Y-1SR Z1 (A12:2011) Add the following subclause: ot such equipment. 1.3.Z1 Exposure to excessive sound pressure The apparatus shall be so designed and constructed as to present no danger when used for its intended purpose, either in normal operating conditions or under fault conditions, particularly providing protection against exposure to excessive sound pressures from headphones or earphones. OTE Z1 A new method of measurement is described in E , Sound system equipment: Headphones and earphones associated with portable audio equipment - Maximum sound pressure level measurement methodology and limit considerations - art 1: General method for one package equipment, and in E , Sound system equipment: Headphones and earphones associated with portable audio equipment - Maximum sound pressure level measurement methodology and limit considerations - art 2: Guidelines to associate sets with headphones coming from different manufacturers. In E :2006/A12:2011 Deleted. Delete the addition of 1.3.Z1 / E :2006 Delete the definition Z1 / E :2006 /A1: Add the following OTE: OTE Z1 The use of certain substances in electrical and electronic equipment is restricted within the EU: see Directive 2002/95/EC (A1:2010) (A ) In addition, for a ORTABLE SOUD SYSTEM, the instructions shall include a warning that excessive sound pressure from earphones and headphones can cause hearing loss. Added. Added. In E :2006/A12:2011 Replaced. Delete OTE Z1 and the addition for ortable Sound System. Add the following clause and annex to the existing standard and amendments. Zx rotection against excessive sound pressure from personal music players Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 29 of 57

30 Report o.: BST Y-1SR-2 Zx.1 General This sub-clause specifies requirements for protection against excessive sound pressure from personal music players that are closely coupled to the ear. It also specifies requirements for earphones and headphones intended for use with personal music players. A personal music player is a portable equipment for personal use, that: is designed to allow the user to listen to recorded or broadcast sound or video; and primarily uses headphones or earphones that can be worn in or on or around the ears; and allows the user to walk around while in use. OTE 1 Examples are hand-held or body-worn portable CD players, M3 audio players, mobile phones with M3 type features, DA s or similar equipment. A personal music player and earphones or headphones intended to be used with personal music players shall comply with the requirements of this sub-clause. The requirements in this sub-clause are valid for music or video mode only. The requirements do not apply: while the personal music player is connected to an external amplifier; or while the headphones or earphones are not used. OTE 2 An external amplifier is an amplifier which is not part of the personal music player or the listening device, but which is intended to play the music as a standalone music player. The requirements do not apply to: hearing aid equipment and professional equipment; OTE 3 rofessional equipment is equipment sold through special sales channels. All products sold through normal electronics stores are considered not to be professional equipment. ot such equipment. analogue personal music players (personal music players without any kind of digital processing of the sound signal) that are brought to the market before the end of OTE 4 This exemption has been allowed because this technology is falling out of use and it is expected that within a few years it will no longer exist. This exemption will not be extended to other technologies. For equipment which is clearly designed or intended for use by young children, the limits of E 71-1 apply. Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 30 of 57

31 Report o.: BST Y-1SR-2 Zx.2 Equipment requirements o safety provision is required for equipment that complies with the following: equipment provided as a package (personal music player with its listening device), where the acoustic output LAeq,T is 85 dba measured while playing the fixed programme simulation noise as described in E ; and a personal music player provided with an analogue electrical output socket for a listening device, where the electrical output is 27 mv measured as described in E , while playing the fixed programme simulation noise as described in E OTE 1 Wherever the term acoustic output is used in this clause, the 30 s A-weighted equivalent sound pressure level LAeq,T is meant. See also Zx.5 and Annex Zx. All other equipment shall: a) protect the user from unintentional acoustic outputs exceeding those mentioned above; and b) have a standard acoustic output level not exceeding those mentioned above, and automatically return to an output level not exceeding those mentioned above when the power is switched off; and ot such equipment. Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 31 of 57

32 Report o.: BST Y-1SR-2 c) provide a means to actively inform the user of the increased sound pressure when the equipment is operated with an acoustic output exceeding those mentioned above. Any means used shall be acknowledged by the user before activating a mode of operation which allows for an acoustic output exceeding those mentioned above. The acknowledgement does not need to be repeated more than once every 20 h of cumulative listening time; and OTE 2 Examples of means include visual or audible signals. Action from the user is always required. OTE 3 The 20 h listening time is the accumulative listening time, independent how often and how long the personal music player has been switched off. d) have a warning as specified in Zx.3; and e) not exceed the following: 1) equipment provided as a package (player with Its listening device), the acoustic output shall be 100 dba measured while playing the fixed programme simulation noise described in E ; and 2) a personal music player provided with an analogue electrical output socket for a listening device, the electrical output shall be 150 mv measured as described in E , while playing the fixed programme simulation noise described in E For music where the average sound pressure (long term LAeq,T) measured over the duration of the song is lower than the average produced by the programme simulation noise, the warning does not need to be given as long as the average sound pressure of the song is below the basic limit of 85 dba. In this case T becomes the duration of the song. OTE 4 Classical music typically has an average sound pressure (long term LAeq,T) which is much lower than the average programme simulation noise. Therefore, if the player is capable to analyse the song and compare it with the programme simulation noise, the warning does not need to be given as long as the average sound pressure of the song is below the basic limit of 85 dba. For example, if the player is set with the programme simulation noise to 85 dba, but the average music level of the song is only 65 dba, there is no need to give a warning or ask an acknowledgement as long as the average sound level of the song is not above the basic limit of 85 dba. ot such equipment. Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 32 of 57

33 Report o.: BST Y-1SR-2 Zx.3 Warning The warning shall be placed on the equipment, or on the packaging, or in the instruction manual and shall consist of the following: the symbol of Figure 1 with a minimum height of 5 mm; and the following wording, or similar: To prevent possible hearing damage, do not listen at high volume levels for long periods. ot such equipment. Figure 1 Warning label (IEC ) Alternatively, the entire warning may be given through the equipment display during use, when the user is asked to acknowledge activation of the higher level. Zx.4 Requirements for listening devices (headphones and earphones) Zx.4.1 Wired listening devices with analogue ot such equipment. input With 94 dba sound pressure output LAeq,T, the input voltage of the fixed programme simulation noise described in E shall be 75 mv. This requirement is applicable in any mode where the headphones can operate (active or passive), including any available setting (for example built-in volume level control). OTE The values of 94 dba 75 mv correspond with 85dBA 27 mv and 100 dba 150 mv. Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 33 of 57

34 Report o.: BST Y-1SR-2 Zx.4.2 Wired listening devices with digital input With any playing device playing the fixed programme simulation noise described in E (and respecting the digital interface standards, where a digital interface standard exists that specifies the equivalent acoustic level), the acoustic output LAeq,T of the listening device shall be 100 dba. This requirement is applicable in any mode where the headphones can operate, including any available setting (for example built-in volume level control, additional sound feature like equalization, etc.). OTE An example of a wired listening device with digital input is a USB headphone. Zx.4.3 Wireless listening devices In wireless mode: with any playing and transmitting device playing the fixed programme simulation noise described in E ; and respecting the wireless transmission standards, where an air interface standard exists that specifies the equivalent acoustic level; and with volume and sound settings in the listening device (for example built-in volume level control, additional sound feature like equalization, etc.) set to the combination of positions that maximize the measured acoustic output for the abovementioned programme simulation noise, the acoustic output LAeq,T of the listening device shall be 100 dba. OTE An example of a wireless listening device is a Bluetooth headphone. Zx.5 Measurement methods Measurements shall be made in accordance with E or E as applicable. Unless stated otherwise, the time interval T shall be 30 s. OTE Test method for wireless equipment provided without listening device should be defined. ot such equipment. ot such equipment. ot such equipment. Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 34 of 57

35 Report o.: BST Y-1SR Replace the subclause as follows: Basic requirements To protect against excessive current, short-circuits and earth faults in RIMARY CIRCUITS, protective devices shall be included either as integral parts of the equipment or as parts of the building installation, subject to the following, a), b) and c): a) except as detailed in b) and c), protective devices necessary to comply with the requirements of 5.3 shall be included as parts of the equipment; b) for components in series with the mains input to the equipment such as the supply cord, appliance coupler, r.f.i. filter and switch, short-circuit and earth fault protection may be provided by protective devices in the building installation; Replaced. c) it is permitted for LUGGABLE EQUIMET TYE B or ERMAETLY COECTED EQUIMET, to rely on dedicated overcurrent and short-circuit protection in the building installation, provided that the means of protection, e.g. fuses or circuit breakers, is fully specified in the installation instructions. If reliance is placed on protection in the building installation, the installation instructions shall so state, except that for LUGGABLE EQUIMET TYE A the building installation shall be regarded as providing protection in accordance with the rating of the wall socket outlet This subclause has been declared void Delete the OTE in Table 3A, and delete also in this table the conduit sizes in parentheses Replace IEC 53 by H05 RR-F ; IEC 52 by H03 VV-F or H03 VVH2-F ; IEC 53 by H05 VV-F or H05 VVH2-F2. In Table 3B, replace the first four lines by the following: Up to and including 6 0,75 a) Over 6 up to and including 10 (0,75) b) 1,0 Over 10 up to and including 16 (1,0) c) 1,5 In the conditions applicable to Table 3B delete the words in some countries in condition a). In OTE 1, applicable to Table 3B, delete the second sentence. Deleted. Replaced. Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 35 of 57

36 Report o.: BST Y-1SR In Table 3D, delete the fourth line: conductor sizes for 10 to 13 A, and replace with the following: Over 10 up to and including 16 1,5 to 2,5 1,5 to 4 Delete the fifth line: conductor sizes for 13 to 16 A (A1:2010) Annex H Bibliograph y Replace the existing OTE by the following: OTE Z1 Attention is drawn to: 1999/519/EC: Council Recommendation on the limitation of exposure of the general public to electromagnetic fields 0 Hz to 300 GHz, and 2006/25/EC: Directive on the minimum health and safety requirements regarding the exposure of workers to risks arising from physical agents (artifical optical radiation). Standards taking into account mentioned Recommendation and Directive which demonstrate compliance with the applicable EU Directive are indicated in the OJEC. Replace the last paragraph of this annex by: At any point 10 cm from the surface of the OERATOR ACCESS AREA, the dose rate shall not exceed 1 µsv/h (0,1 mr/h) (see OTE). Account is taken of the background level. Replace the notes as follows: OTE These values appear in Directive 96/29/Euratom. Delete OTE 2. Additional E standards. Deleted. Added. Replaced. ZB AEX (normative) SECIAL ATIOAL CODITIOS (E) In Denmark, certain types of Class I appliances (see ) may be provided with a plug not establishing earthing conditions when inserted into Danish socket-outlets In orway and Sweden, for requirements see and 7.3 of this annex In Finland, orway and Sweden, resistors bridging BASIC ISULATIO in CLASS I LUGGABLE EQUIMET TYE A must comply with the requirements in In addition when a single resistor is used, the resistor must withstand the resistor test in Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 36 of 57

37 Report o.: BST Y-1SR-2 ZB AEX (normative) SECIAL ATIOAL CODITIOS (E) In orway, due to the IT power system used (see annex V, Figure V.7), capacitors are required to be rated for the applicable line-to-line voltage (230 V) In Finland, orway and Sweden, the third dashed sentence is applicable only to equipment as defined in of this annex. Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 37 of 57

38 Report o.: BST Y-1SR-2 ZB AEX (normative) SECIAL ATIOAL CODITIOS (E) In Finland, orway and Sweden, CLASS I LUGGABLE EQUIMET TYE A intended for connection to other equipment or a network shall, if safety relies on connection to protective earth or if surge suppressors are connected between the network terminals and accessible parts, have a marking stating that the equipment must be connected to an earthed mains socket-outlet. The marking text in the applicable countries shall be as follows: In Finland: "Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan" In orway: Apparatet må tilkoples jordet stikkontakt In Sweden: Apparaten skall anslutas till jordat uttag In orway and Sweden, the screen of the cable distribution system is normally not earthed at the entrance of the building and there is normally no equipotential bonding system within the building. Therefore the protective earthing of the building installation need to be isolated from the screen of a cable distribution system. It is however accepted to provide the insulation external to the equipment by an adapter or an interconnection cable with galvanic isolator, which may be provided by e.g. a retailer. The user manual shall then have the following or similar information in orwegian and Swedish language respectively, depending on in what country the equipment is intended to be used in: Equipment connected to the protective earthing of the building installation through the mains connection or through other equipment with a connection to protective earthing and to a cable distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection to a cable distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator, see E ). Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 38 of 57

39 Report o.: BST Y-1SR-2 ZB AEX (normative) SECIAL ATIOAL CODITIOS (E) OTE In orway, due to regulation for installations of cable distribution systems, and in Sweden, a galvanic isolator shall provide electrical insulation below 5 MHz. The insulation shall withstand a dielectric strength of 1,5 kv r.m.s., 50 Hz or 60 Hz, for 1 min. Translation to orwegian (the Swedish text will also be accepted in orway): Utstyr som er koplet til beskyttelsesjord via nettplugg og/eller via annet jordtilkoplet utstyr og er tilkoplet et kabel-tv nett, kan forårsake brannfare. For å unngå dette skal det ved tilkopling av utstyret til kabel-tv nettet installeres en galvanisk isolator mellom utstyret og kabel- TV nettet. Translation to Swedish: Utrustning som är kopplad till skyddsjord via jordat vägguttag och/eller via annan utrustning och samtidigt är kopplad till kabel-tv nät kan i vissa fall medfőra risk főr brand. Főr att undvika detta skall vid anslutning av utrustningen till kabel-tv nät galvanisk isolator finnas mellan utrustningen och kabel-tv nätet In Denmark, socket-outlets for providing power to other equipment shall be in accordance with the Heavy Current Regulations, Section D1, Standard Sheet DK 1-3a, DK 1-5a or DK 1-7a, when used on Class I equipment. For STATIOARY EQUIMET the socket-outlet shall be in accordance with Standard Sheet DK 1-1b or DK 1-5a. For CLASS II EQUIMET the socket outlet shall be in accordance with Standard Sheet DKA 1-4a In orway, for requirements see , and of this annex In Finland, orway and Sweden there are additional requirements for the insulation. See and of this annex In orway, for requirements see , and of this annex In the United Kingdom, the current rating of the circuit shall be taken as 13 A, not 16 A. o socket-outlet provided. o TV. o TV. o TV. Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 39 of 57

40 Report o.: BST Y-1SR-2 ZB AEX (normative) SECIAL ATIOAL CODITIOS (E) In the United Kingdom, to protect against excessive currents and short-circuits in the RIMARY CIRCUIT of DIRECT LUG-I EQUIMET, tests according to 5.3 shall be conducted, using an external protective device rated 30 A or 32 A. If these tests fail, suitable protective devices shall be included as integral parts of the DIRECT LUG-I EQUIMET, so that the requirements of 5.3 are met In Finland, orway and Sweden, there are additional requirements for the insulation, see and of this annex In Switzerland, supply cords of equipment having a RATED CURRET not exceeding 10 A shall be provided with a plug complying with SEV 1011 or IEC and one of the following dimension sheets: SEV lug Type E 250/400 V, 10 A SEV lug Type V, 10 A L+ SEV lug Type 12 L++E 250 V, 10 A In general, E applies for plugs for currents exceeding 10 A. However, a 16 A plug and socket-outlet system is being introduced in Switzerland, the plugs of which are according to the following dimension sheets, published in February 1998: SEV : lug Type 25, 3L++E 230/400 V, 16 A SEV :lug Type 21, L+, 250 V, 16A SEV : lug Type 23, L++E 250 V, 16 A o TV Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 40 of 57

41 Report o.: BST Y-1SR-2 ZB AEX (normative) SECIAL ATIOAL CODITIOS (E) In Denmark, supply cords of single-phase equipment having a rated current not exceeding13 A shall be provided with a plug according to the Heavy Current Regulations, Section D1. CLASS I EQUIMET provided with socketoutlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules shall be provided with a plug in accordance with standard sheet DK 2-1a or DK 2-5a. If poly-phase equipment and single-phase equipment having a RATED CURRET exceeding 13 A is provided with a supply cord with a plug, this plug shall be in accordance with the Heavy Current Regulations, Section D1 or E In Spain, supply cords of single-phase equipment having a rated current not exceeding 10 A shall be provided with a plug according to UE 20315:1994. Supply cords of single-phase equipment having a rated current not exceeding 2,5 A shall be provided with a plug according to UE-E 50075:1993. CLASS I EQUIMET provided with socketoutlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules, shall be provided with a plug in accordance with standard UE 20315:1994. If poly-phase equipment is provided with a supply cord with a plug, this plug shall be in accordance with UE-E Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 41 of 57

42 Report o.: BST Y-1SR-2 ZB AEX (normative) SECIAL ATIOAL CODITIOS (E) In the United Kingdom, apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to BS 1363 by means of that flexible cable or cord and plug, shall be fitted with a standard plug in accordance with Statutory Instrument 1768: The lugs and Sockets etc. (Safety) Regulations 1994, unless exempted by those regulations. OTE Standard plug is defined in SI 1768:1994 and essentially means an approved plug conforming to BS 1363 or an approved conversion plug In Ireland, apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to I.S. 411 by means of that flexible cable or cord and plug, shall be fitted with a 13 A plug in accordance with Statutory Instrument 525: ational Standards Authority of Ireland (section 28) (13 A lugs and Conversion Adaptors for Domestic Use) Regulations In Switzerland, for requirements see of this annex In the United Kingdom, a power supply cord with conductor of 1,25 mm2 is allowed for equipment with a rated current over 10 A and up to and including 13 A In the United Kingdom, the range of conductor sizes of flexible cords to be accepted by terminals for equipment with a RATED CURRET of over 10 A up to and including 13 A is: 1,25 mm 2 to 1,5 mm 2 nominal cross-sectional area. Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 42 of 57

43 Report o.: BST Y-1SR-2 ZB AEX (normative) SECIAL ATIOAL CODITIOS (E) In the United Kingdom, the torque test is performed using a socket outlet complying with BS 1363 part 1:1995, including Amendment 1:1997 and Amendment 2:2003 and the plug part of DIRECT LUG-I EQUIMET shall be assessed to BS 1363: art 1, 12.1, 12.2, 12.3, 12.9, 12.11, 12.12, 12.13, and 12.17, except that the test of is performed at not less than 125 C. Where the metal earth pin is replaced by an Insulated Shutter Opening Device (ISOD), the requirements of clauses 22.2 and 23 also apply In Ireland, DIRECT LUG-I EQUIMET is known as plug similar devices. Such devices shall comply with Statutory Instrument 526: ational Standards Authority of Ireland (Section 28) (Electrical plugs, plug similar devices and sockets for domestic use) Regulations, In Finland, orway and Sweden TOUCH CURRET measurement results exceeding 3,5 ma r.m.s. are permitted only for the following equipment: STATIOARY LUGGABLE EQUIMET TYE A that is intended to be used in a RESTRICTED ACCESS LOCATIO where equipotential bonding has been applied, for example, in a telecommunication centre; and has provision for a permanently connected ROTECTIVE EARTHIG CODUCTOR; and is provided with instructions for the installation of that conductor by a SERVICE ERSO; STATIOARY LUGGABLE EQUIMET TYE B; STATIOARY ERMAETLY COECTED EQUIMET. Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 43 of 57

44 Report o.: BST Y-1SR-2 ZB AEX (normative) SECIAL ATIOAL CODITIOS (E) (A1:2010) In Finland, orway and Sweden, add the following text between the first and second paragraph of the compliance clause: If this insulation is solid, including insulation forming part of a component, it shall at least consist of either - two layers of thin sheet material, each of which shall pass the electric strength test below, or - one layer having a distance through insulation of at least 0,4 mm, which shall pass the electric strength test below. Alternatively for components, there is no distance through insulation requirements for the insulation consisting of an insulating compound completely filling the casing, so that CLEARACES and CREEAGE DISTACES do not exist, if the component passes the electric strength test in accordance with the compliance clause below and in addition - passes the tests and inspection criteria of with an electric strength test of 1,5 kv multiplied by 1,6 (the electric strength test of shall be performed using 1,5 kv), and - is subject to ROUTIE TESTIG for electric strength during manufacturing, using a test voltage of 1,5 kv. o TV Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 44 of 57

45 Report o.: BST Y-1SR-2 ZB AEX (normative) SECIAL ATIOAL CODITIOS (E) It is permitted to bridge this insulation with an optocoupler complying with b). It is permitted to bridge this insulation with a capacitor complying with E :2005, subclass Y2. A capacitor classified Y3 according to E :2005, may bridge this insulation under the following conditions: - the insulation requirements are satisfied by having a capacitor classified Y3 as defined by E , which in addition to the Y3 testing, is tested with an impulse test of 2,5 kv defined in E :2006, ; - the additional testing shall be performed on all the test specimens as described in E ; - the impulse test of 2,5 kv is to be performed before the endurance test in E , in the sequence of tests as described in E In Finland, orway and Sweden, the exclusions are applicable for ERMAETLY COECTED EQUIMET, LUGGABLE EQUIMET TYE B and equipment intended to be used in a RESTRICTED ACCESS LOCATIO where equipotential bonding has been applied, e.g. in a telecommunication centre, and which has provision for a permanently connected ROTECTIVE EARTHIG CODUCTOR and is provided with instructions for the installation of that conductor by a SERVICE ERSO. 7.2 In Finland, orway and Sweden, for requirements see and of this annex. The term TELECOMMUICATIO ETWORK in being replaced by the term CABLE DISTRIBUTIO SYSTEM. 7.3 In orway and Sweden, for requirements see and of this annex. 7.3 In orway, for installation conditions see E :2005. o TV Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 45 of 57

46 Report o.: BST Y-1SR TABLE: List Of Critical Components Components Manufacturers / Trademark Enclosure Various Various Types / Model Technical data Standard Rated V-0, 105 degree C, minimum UL746C Mark(s) of conformity UL CB Various Various V-0,130 UL94 UL Output Wire Various Various 300V, 80 C, VW-1 UL 758 UL Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 46 of 57

47 Report o.: BST Y-1SR TABLE: Electrical Data (In ormal Conditions) fuse # Irated (A) U (V) F(Hz) (W) condition/status Maximum normal load Supplementary information: Load with rated value c1) TABLE:max.V,A,VA test Voltage(rated) (V) Current(rated) (A) Voltage(max.) (V) Current(max.) (A) VA(max.) (VA) Supplementary information: The above measurements are the maximum values(max.v and max.a not obtained at the same time) 2.2 TABLE: evaluation of voltage limiting component in SELV circuits Component(measured between) Max.voltage(V) (normal operation) V peak V d.c Voltage Limiting Components T1 pina to B Fault test performed on voltage limiting components Voltage measured(v) in SELV circuits (V peak or V d.c.) Supplementary information:s-c=short circuit. Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 47 of 57

48 Report o.: BST Y-1SR TABLE: Limited Current Circuits Test Location Voltage Freq. Current Limit (ma) (V) (Hz) (ma) Supplementary information: - *)2Kohm resistor is connected between output - and earth 2.5 TABLE: Limited power sources Circuit output tested: Measured Uoc(V) with all load circuits Disconnected: Isc(A) VA Meas. Limit Meas. Limit Supplementary information: Humidity Condition Test Test condition: 28 C, 93%, 48hrs Test voltage applied between: Test voltage (V) Breakdown Input to output AC 3000 o Input to enclosure AC 1500 o BI: Basic insulation SI: Supplementary insulation RI: Reinforced insulation; FI: Functional Insulation Humidity Chamber: ; Stop watch: ; Withstanding Voltage Tester: TABLE: working voltage measurement Location RMS voltage(v) eak voltage(v) Comments Supplementary information: The highest measured working voltages in transformer are indicated with bold character. Vin=240Vac,60Hz Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 48 of 57

49 Report o.: BST Y-1SR and TABLE:Clearance and creepage distance measurements Clearance (cl) and creepage U peak U r.m.s. Required cl Measured cl distance (cr) at/of/between: (V) (V) (mm) (mm) Required cr (mm) L to T1 ri-sec on CB Supplementary information: Measur ed cr (mm) TABLE: distance through insulation measurements distance through insulation di at/of: Up test voltage required di di (V) (V) (mm) (mm) Reinforced: plastic enclosure Vac Supplementary information: o flash over or insulation breakdown after test Drop Test Height: 1000mm Impact Area Drop Times Drop o. Observation Stress relief test Temp. equal to 10 C plus max. temp measured on enclosure during test of 4.5.1: T-Tamb+Tma+10 C = C, 7h 95 C, 7h ass: If any cracks or damages occur which do not change the normal shape or allow reduction of protection against electric shock then they are disregarded. Otherwise the pass verdict will be established by the roject Engineer. Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 49 of 57

50 Report o.: BST Y-1SR TABLE: Batteries The tests of are applicable only when appropriate battery data is not available Is it possible to install the battery in a reverse polarity position? Max. current during normal condition Max. current during fault condition on-rechargeable batteries Rechargeable batteries Discharging Unintentional Meas. Manuf. Meas. Manuf. Meas. Manuf. Charging Discharging Reversed charging Meas. Manuf. current Specs. charging current Specs. current Specs. current Specs Test results: - Chemical leaks - Explosion of the battery - Emission of flame or expulsion of molten metal - Electric strength tests of equipment after completion of tests Supplementary information: Verdict TABLE: Batteries Battery category...: (Lithium, imh, icad, Lithium Ion ) Manufacturer...: Type / model...: Voltage...: Capacity...: mah Tested and Certified by (incl. Ref. o.)...: Circuit protection diagram: MARKIGS AD ISTRUCTIOS ( ) Location of replaceable battery Language(s).: Close to the battery.: In the servicing instructions : In the operating instructions..: Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 50 of 57

51 Report o.: BST Y-1SR TABLE: Temperature Rise Measurements Location 76.5V Temperature( ) Test voltage (V) 290.4V Temperature( ) Allowed Temperature( ) C1 body T Switch Output wire Enclosure inside Enclosure outside Ambient Comments: The temperatures were measured by thermal couple (type K) method under worst case normal mode defined in load as described in at voltage described in The worst case at normal mode is defined with max load of the adaptor. With max. ambient temperature specified as 25 C, therefore, the maximum temperature rise is calculated as follows: Winding components: - winding of 110 (Class B or better) Components with: TABLE: ball pressure test of thermoplastic parts part allowed impression diameter (mm): test temperature (*XC) impression diameter (mm) Terminal Switch supplementary information: TABLE: Resistance to fire art Manufacturer of material Type of material Thickness (mm Flammability class Evidence Terminal Supplementary information: Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 51 of 57

52 Report o.: BST Y-1SR Table: touch current measurement Measured between: Measured Limit Comments (ma) (ma) Live Enclosure e C; 1 ; ri S. - On eutral Enclosure e C; 1 R; ri S. - On supplementary information: ote(s): 5.2 TABLE: Electric strength tests, impulse tests and voltage surge tests Test voltage applied between: Test voltage (V) Breakdown Input to Output Input to Enclosure Supplementary information: AC 3000 AC 1500 o o BI: Basic insulation SI: Supplementary insulation RI: Reinforced insulation; FI: Functional Insulation Withstanding Voltage Tester: 5.3 TABLE: Fault Condition Tests -- Ambient temperature ( C) 25 C, if not otherwise stated ower source for EUT: Manufacturer, model/type, output rating... : o. Component o. Fault Test Voltage (V) Refer to page 2. Test Time Fuse o. Fuse Current (A) Result 1 Q1 S-C min - Unit shut down immediately, recoverable. 2 C1 S-C 110 1s - Unit shut down immediately, Fuse open. 3 Output termianl s-c s - - Unit shut down immediately. Recoverable. o hazard. Supplementary information Fault: S-C=short circuit, O-L =overload, B-L = blocked, O-C =open circuit.for fuse-opened conditions, same results came out for all sources of fuse. If fuse not open have repeat test three times Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 52 of 57

53 Report o.: BST Y-1SR-2 AEX A: hoto-documentation Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 53 of 57

54 Report o.: BST Y-1SR-2 hoto 1 General Appearance of the EUT hoto 2 General Appearance of the EUT Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 54 of 57

55 Report o.: BST Y-1SR-2 hoto 3 General Appearance of the EUT hoto 4 General Appearance of the EUT ] Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 55 of 57

56 Report o.: BST Y-1SR-2 hoto 5 General Appearance of the EUT hoto 6 General Appearance of the EUT Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 56 of 57

57 Report o.: BST Y-1SR-2 hoto 7 General Appearance of the EUT Building o.23-24, Zhiheng Industrial ark, Guankouer Road, antou,anshan District,Shenzhen,Guangdong,China age 57 of 57