IEC , 2 Ed. ( ) TESTING AND MEASURING EQUIPMENT/ALLOWED SUBCONTRACTING

Transcription

1 IEC YTEM FOR CONFIRMITY TETING AND COMMITTEE OF TETING LABORATORIE IEC , 2 Ed. ( ) TETING AND MEAURING EQUIPMENT/ALLOWED UBCONTRACTING R = Required to be at Lab IEC test equipment has been identified for use in the sub-grouped below: RA = Required for Amplifiers; in addition to, required for apparatus with audio amplifiers (audio power > 0,5 Watts) = Required Basic - test and measurement equipment required for all apparatus RC = Required for Cable distribution system; in addition to, required for apparatus with connection(s) to a cable distribution system RH = Required for Hredder; in addition to, required for shredder RT = Required for Telecom; in addition to, required for apparatus with connection(s) to a telecommunication network RV = Required for CRT / Plasma/LCD or other Video equipment in addition to required for testing CRT Cathode ray Tubes/ picture tubes, plasma/lcd or other video apparatus = May be ubcontracted P = Pecialized testing facility W = May be Witnessed at MTL Clause Measurement/testing Testing / measuring equipment / material needed ubcontracting 4.7 Equipment for direct Test equipment (see Fig. 11 of IEC 60065) insertion in to mains socket-outlets 4.8 Coin/button cell batteries 30 N ± 1N applied by rigid test finger (Figure V.2); test hook (Figure 20) Crush Test 300 N ± 5N; flat surface measuring 100 mm by 250 mm; timer teady- state voltage and Amp- and voltmeter suitable for the current and waveform, frequency meter current limits Measuring instruments in according IEC 60990: 1999 Figure 4 and ingle pulse limits Oscilloscope Accessibility to electrical Blunt probe of Figure V.3 energy sources and safeguards Thermoplastic parts on Vicat test B 50 of IO 306 which conductive metallic Ball pressure test apparatus according to IEC parts are directly mounted Oven at least 125ºC , Maximum operating Voltage supply ingle phase voltage supply systems/variability/adequacy

2 IEC YTEM FOR CONFIRMITY TETING AND COMMITTEE OF TETING LABORATORIE Clause 5.4.2, 5.4.3, Measurement/testing Testing / measuring equipment / material needed ubcontracting temperatures for materials, components and systems Clearances, creepage distance, solid insulation Three phase voltage supply systems Temperature (rise) Temperature recorder (multi-channel) Thermocouples Winding resistance (normally > 1,0 2-wire, 4-wire <1,0 ). Voltage Voltmeters (ac/dc) High voltage meter (probe) Current Currents (ac/dc) Loading Loads (resistive) Oscilloscope Dial gauge or caliper Micrometer Pins etc. With different diameters Microscope Impulse test generator circuit 1 of Table D.1. Impulse test generator circuit 2 of Table D.1. impulse test generator circuit 3 of Table D.1 RT RC Test equipment for tracking index per IEC Mandrel (figure 25 to 28), metal foil, equipment suitable for electrical strength test loads top watch, weight Antenna terminal Insulation resistance meter (500V > 4 MΩ), Impulse test generator circuit 1 of Table D.1 RC insulation Thermal cycling test Full draught oven ( 2ºC) procedure Cooling facility (0º±2 C) Humidity conditioning Chamber RH( 93 ± 3)%, C Chamber RH (93 ± 3)%, (40 ± 2) C Extra large environmental testing chamber P Electrical strength test Test Instrument/equipment according to Figure 29 for electric strength afeguards against transient voltages from Test Instrument/equipment according to Figure 29 for electric strength (of solid/thin sheet insulation). Blunt probe figure V.3

3 IEC YTEM FOR CONFIRMITY TETING AND COMMITTEE OF TETING LABORATORIE Clause Measurement/testing Testing / measuring equipment / material needed ubcontracting external circuits eparation between external Non-inductive Resistor 5000Ω Ampere meter circuits and earth Capacitor discharge Measuring instrument with input impedance 100M or more in parallel with an input capacitance of 25pF or less Annex T Annex T Force of 10 N ± 1 N Resistance of protective conductors and their terminations Determination of the overcurrent protective device and circuit (Annex R) 5.7 Prospective touch voltage, touch current and protective conductor current Power source circuit classification Top openings and top openings properties 8.2 Mechanical energy source classifications Equipment having an electromechanical device for destruction of media High current source with a voltage not exceeding 12 V, ource with at least 1500A short circuit Networks in according IEC 60990:1999 figures 4 and 5; Amp-meter Watt meter, variable resistor load, stop watch Cheesecloth bleached cotton cloth 40g/m 2 cale up to 25kg Test probe (jointed) of Annex V (figure V.1 and V.2) and wedge probe V.4 Force 45N and 90 N with wedge probe RH High pressure lamps Dark sticky mat,, magnified glass with a resolution of 0,1 mm tatic stability for floor Inclined plane 15 standing equipment (Inclined plane 10 Force 250N/ Test tool 800Nwith a flat surface 12,5cm by 20cm Glass slide test Glass plate, Horizontal force test Inclined plane 15, force 100N

4 IEC YTEM FOR CONFIRMITY TETING AND COMMITTEE OF TETING LABORATORIE Clause Measurement/testing Testing / measuring equipment / material needed ubcontracting 8.7 Equipment mounted to a everal weights, timer wall or ceiling Torque gauges 8.8 Handle strength test method 75mm width, several weights, scale, timer 8.9 Wheels or casters attachment requirement 8.10 Carts, stands and similar carriers Force 20N, stop watch Force up to 440 N with a circular plan surface 30mm,, stop watch, 8.11 Mounting means for rack everal weights, timer mounted equipment 8.12 Telescoping or rod antennas (Annex T.11) test tool for applying torque up to 0,6Nm, test tool for applying force 20N, stop watch RA 10 Radiations Laser (including laser diodes) everal special equipment for laser classification(iec ) Light emitting diodes (LEDs) everal special equipment for LED classification(iec 62471:2006) X-ray Radiation monitor, ionizing chamber type with an effective area of mm² Effect of UV radiation on Test equipment according to IO 178, 179, 180, 527 and materials (Annex C) 8256 and according IO 4892 series. Human exposure to UV radiation Measuring equipment according to IEC (Annex C) Acoustics pecial equipment for acoustic measurements (EN /-2) Annex B.2.5 Input test Amp-meter suitable for the current and waveform, power meter, voltmeter, Variable loads ignal generator in acc. IEC :1997 RV Annex B.3.2 Covering of ventilation piece of card with 200 g/m² density openings Annex E Test conditions for Testing box RA equipment contain audit ignal generator (sinus) 1kHz or alternative RA amplifiers Band-pass filter for wide-band noise measurement, pink noise signal generator Annex F Durability water/piece of cloth/ timer

5 IEC YTEM FOR CONFIRMITY TETING AND COMMITTEE OF TETING LABORATORIE Clause Measurement/testing Testing / measuring equipment / material needed ubcontracting Annex Durability Petroleum spirit (85% n-hexane), (CA# ) F Annex Alternative test method Cheesecloth (bleached cotton cloth 40g/m 2 ), Wrapping Tissue (12g/ m 2 30g/m 2 ) G G G Annex G.7 Mains supply cords Test equipment according IEC Appropriate weights Torque meter or equivalent Annex G.9 IC current limiters resistor: 100 Ω +/- 5 Ω capacitor: 425 μf +/- 10µF inductance: 0,35 mh +/- 0,1mH; <1 Ω dc resistance Oven with a range of -30 C+/-2 C up to 70 C +/-2 C 50 C± 2 C for 10 min; followed by 10 min at 0 C± 2 C with a 5 min period of transition from one state to the other Annex G.10 Annex G Annex G Annex G.15 Test for resistor serving as safeguard Impulse test generator circuit 1 of Table D.1. Impulse test generator circuit 2 of Table D.1. impulse test generator circuit 3 of Table D.1 Test according to IEC Full draught oven (± 2ºC) Test method and compliance criteria Abrasion resistance test cratch test device with steel pin Pressurized liquid filled components Hydrostatic pressure Hydrostatic pressure test device Tubing and fittings Tensile strength test device in acc to IO 527 series compatibility test Vibration test Vibration generator (0,35mm/10Hz-55Hz-10Hz) IEC Annex G.16 Discharge function Chamber RH( 93 ± 3)%, ºC, (40 ± 2)ºC Impulse test generator circuit 2 of Table D.1. Annex H Criteria for telephone ringing signals 5 000Ω resistor RT RT RC

6 IEC YTEM FOR CONFIRMITY TETING AND COMMITTEE OF TETING LABORATORIE Clause Annex J Measurement/testing Testing / measuring equipment / material needed ubcontracting Insulated winding wires for use without interleaved insulation Charging voltage and current Test equipment according to IEC ,IEC and IEC Annex M.4.2, Oven M Annex M.6.2 Leakage current Insulation resistance meter Annex M.8.2 Annex P.2 Annex. P.4 Protection against internal ignition from external spark sources park Test afeguards against entry of solid foreign objects Metallized coatings and adhesives securing parts Tests for resistance to heat and fire Equipment according to IEC :2005 ub cl. 6.4 uitable tool (or tools) to simulate a straight metal object, 1mm in diameter, length up to 13 mm Oven Annex Needle flame test apparatus acc. to IEC :2004 P Distillate fuel oil as described in Annex W flame test apparatus in acc. to IEC :1999 P Cheesecloth (bleached cotton cloth 40g/m 2 ), Wrapping Tissue (12g/ m 2 30g/m 2 ) Annex teady force test 10N ± 1N T.2 - T.4 Test finger (figure V1 or V2 unjointed, 30N 3N) Test tool 100N 10N with a circular plan surface 30mm top watch Annex T.5 teady force test, 250 N Test tool 250N 10N with a circular plan surface 30mm. Annex T.6 Enclosure impact test 50mm/500g 25g steel ball Annex T.7 Drop test Hard wood 13mm on 18mm ± 2mm plywood, two layers. ruler up to 1000 mm ± 10mm AnnexT.8 tress relief test Measuring equipment according to IEC or Oven 70K over normal temp. Annex T.9 Impact Test steel ball 50mm, approx 500g., Fragmentation test Centre punch and a square of 50 mm side Annex U Annex V.1.2 Mechanical strength of CRTs and protection against the effects of implosion Test method 1 urfaces and openings tested with Test equipment acc.iec cale, diamond stylus, cooling liquid, timer Figure V.1 Jointed test probe for equipment likely to be accessible to children Figure V.2 Jointed test probe for equipment not likely to be accessible to children

7 IEC YTEM FOR CONFIRMITY TETING AND COMMITTEE OF TETING LABORATORIE Clause Measurement/testing Testing / measuring equipment / material needed ubcontracting jointed test probes Annex V.1.3 Test method 2 Openings Figure V.1: straight unjointed version of the respective test probe applied with a force of 30 N. tested with straight unjointed test probes Annex V.1.4 Test method 3 Figure V.3 Blunt probe Plugs, jacks, connectors Annex V.1.5 Test method 4 lot openings Figure V.4 Wedge probe RH Annex V.1.6 Test method 5 Terminals Force 1 N ± 0,1N intended to be used by an Terminal probe IEC 61032:1997 figure 4 ordinary person Note: The presence of equipment alone does not indicate a satisfactory situation. Assessors must evaluate the equipment design, calibration, uncertainty and documentation to ensure compliance with the directions of the standard. The requirements of IO/IEC regarding validation are applicable, as the tests of this standard are not standardised tests.