TEST REPORT IEC Audio, video and similar electronic apparatus - Safety requirements

Transcription

1

2

3

4 Test Report issued under the responsibility of: TEST REORT IEC Audio, video and similar electronic apparatus - Safety requirements Report Number.... : Date of issue... : See cover page Total number of pages... : See cover page Applicant s name... : Hisense Electric Co., Address... : No. 218, Qianwangang Road, Qingdao Economic & Technology, Development Zone, Shandong ,.R. China Test specification: Standard... : Test procedure... : COC-LVD Non-standard test method... : Test Report Form No.... : IEC60065K Test Report Form(s) Originator... : Intertek Semko AB Master TRF... : Dated EN 60065: A1: A11: A2:2010 +A12:2011 Copyright 2010 Worldwide System for Conformity Testing and Certification of Electrotechnical Equipment and Components (IECEE), Geneva, Switzerland. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description... : LCD TV Trade Mark... : Hisense Manufacturer... : Same as applicant Model/Type reference... : HE50K3300UWTS, H50M3300, H50M3306, H50M3308 H50MEC3350, H50MEC3355 Ratings... : AC V, 50Hz, 145W

5 age 3 of 51 Report No.: Testing procedure and testing location: Testing Laboratory: TÜV Rheinland / CCIC (Qingdao) Co., Testing location/ address... : 6F, No.2 Bldg., No.175 Zhuzhou Road, Qingdao ,.R. China Associated Laboratory: Testing location/ address... : Tested by (name + signature)... : Approved by (name + signature)... : Testing procedure: TM Testing location/ address...: See cover page See cover page Tested by (name + signature)... : Approved by (name + signature)... : Testing procedure: WMT Testing location/ address...: Tested by (name + signature)... : Witnessed by (name + signature)... : Approved by (name + signature)... : Testing procedure: SMT Testing location/ address...: Tested by (name + signature)... : Approved by (name + signature)... : Supervised by (name + signature)... : Testing procedure: RMT Testing location/ address...: Tested by (name + signature)... : Approved by (name + signature)... : Supervised by (name + signature)... :

6 age 4 of 51 Report No.: List of Attachments (including a total number of pages in each attachment): - ATTACHMENT 1 - National Differences (16 pages) - ATTACHMENT 2 - hoto documentation (10 pages) Note: Total number of pages in each attachment is indicated in individual attachment. The EMF test was evaluated in test report No Summary of testing: The EUT had been evaluated according to the maximum ambient temperature of 35ºC specified by the manufacturer. All applicable tests performed with the following condition: 1k Hz audio output power, Max. contrast, Max. brightness (100%), and max. H. and V. size, USB port is loaded with 0.5A or 1.0A as specified. Tests performed (name of test and test clause): Marking and instructions Clause 5 Heating under normal operation conditions Clause 7.1 Touch current Clause Withdrawal of mains plug Clause Resistance to external forces Clause Surge Test Clause 10.1 Humidity treatment Clause 10.2 Insulation resistance & Dielectric strength Clause 10.3 Touch current under fault condition Clause 11.1 Fault conditions Clause 11.2 Heating under fault conditions Clause Bump Test Clause Impact Test Clause Stress Relief Test Clause Fixing of actuating elements Clause 12.2 Working Voltages Clause 13.2 Electrical connections & mech. Fixings Clause 17.1 Test on plan 10 o to the horizontal Clause N vertical force test Clause 19.2 Remark: Relevant tests were tested on the sample registered No. A The sample is an engineering sample without serial number. Testing location: Unless otherwise indicated, all tests were performed at the location stated in Testing procedure and testing location. Summary of compliance with National Differences List of countries addressed: EU Group Differences, EU Special National Conditions. Refer to the ATTACHMENT 1 of this test report for details.

7 Copy of marking plate age 5 of 51 Report No.: The artwork below may be only a draft. The use of certification marks on a product must be authorized by the respective NCBs that own these marks. <HE50K3300UWTS> Remark: The marking plates for the other models are similar with the ones listed above except for model name.

8 age 6 of 51 Report No.: Test item particulars... : Classification of installation and use... : Class II Supply Connection... : Detachable supply cord ossible test case verdicts: - test case does not apply to the test object...: (Not Applicable) - test object does meet the requirement...: (ass) - test object does not meet the requirement...: F (Fail) Testing: Date of receipt of test item...: See cover page Date (s) of performance of tests...: See cover page General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(see Enclosure #)" refers to additional information appended to the report. "(see appended table)" refers to a table appended to the report. Throughout this report a comma / point is used as the decimal separator. Manufacturer s Declaration per sub-clause of IECEE 02: The application for obtaining a CB Test Certificate includes more than one factory location and a declaration from the Manufacturer stating that the sample(s) submitted for evaluation is (are) representative of the products from each factory has been provided... : Yes Not applicable When differences exist; they shall be identified in the General product information section. Name and address of factory (ies)... : Hisense Electric Co., No. 218, Qianwangang Road, Qingdao Economic & Technology, Development Zone, Shandong ,.R. China General product information: The EUTs are ordinary LCD TVs with LED backlight, which are normally for home use within the scope of IEC/EN All listed models are identical except for model name. The EUTs are class II apparatus, which mainly contain AC inlet, non-approved class II construction power supply board, LCD panel, mainboard with tuner and speakers. All parts are covered by enclosures and fixed with screws. For critical components detail refer to table14. The EUTs are operated up to 2000m above sea level as declared by the manufacturer. No wall mounting brackets accessories provided with the EUTs.

9 age 7 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 3 General requirements Safety class of the apparatus... : Class II 4 General test conditions Ventilation instructions require the use of the test box Measured according to proper ventilation conditions specified in user s manual. 5 Marking and instructions Comprehensible and easily discernible ermanent durability against water and petroleum spirit Markings are permanent, comprehensible and easily discernible on the apparatus. The label and marking were rubbed with cloth soaked with water for 15s then again soaked with petroleum spirit for 15s. After the test there was no damage to the label and marking. The marking didn t fade. There was neither curling nor lifting of the label edge. 5.1 a) Identification, maker... : See marking label b) Model number or type reference... : See marking label c) Class II symbol if applicable... : Used according to IEC d) Nature of supply... : Used according to IEC e) Rated supply voltage... : See marking label f) Mains frequency if safety dependant... : See marking label g) Rated current or power consumption for apparatus supplied by supply apparatus for general use... : Measured current or power consumption... : Deviation % (max 10%)... : h) Rated current or power consumption for apparatus intended for connection to an a.c. mains supply. : Measured current or power consumption... : See below Measured current or power consumption for Television set... : For use with single phase mains supply. See test data in appended table 7.1. Deviation % (max 10%)... : Not more than 10% 5.2 a) Earth terminal Class II apparatus b) Hazardous live terminals No such terminals

10 age 8 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict c) Markings on supply output terminals For USB, DC 5V, 0.5A (Max.) or DC 5V, 1.0A (Max.) 5.3 a) Use of triangle with exclamation mark The symbol was marked on circuit diagram for safety related components. b) marking on loudspeaker grille, IEC No such construction. 5.4 Instructions for use Instruction manual for safety was available and English version was checked a) Mains powered equipment not exposed to dripping or splashing. Warning concerning objects filled with liquid, etc. rovided in user manual. b) Hazardous live terminals, instructions for wiring No such terminals. c) Instructions for replacing lithium battery No such battery used. d) Class I earth connection warning Class II apparatus. e) Instructions for multimedia system connection rovided in user manual. f) Special stability warning for attachment of the apparatus to the floor/wall g) Warning: battery exposure to heat rovided in user manual. h) Warning: protective film on CRT face a-b) Disconnect device: plug/coupler or all-pole mains switch location, accessibility and markings c) Instructions for permanently connected equipment Marking, signal lamps or similar for completely disconnection from the mains MAINS plug of detachable supply cord used as disconnect device. 6 Hazardous radiation 6.1 Ionizing radiation < 36 pa/kg (0,5 mr/h) No ionizing radiation in the apparatus. Ionizing radiation under fault condition 6.2 Laser radiation, emission limits to IEC : : Emission limits under fault conditions... : No laser radiation in the apparatus. 7 Heating under normal operating conditions 7.1 Temperature rises not exceeding specified values; fuse links and other protective devices defeated (see appended table) Temperature rise of accessible parts (see appended table) Temperature rise of parts providing electrical insulation (see appended table)

11 age 9 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Temperature rise of parts acting as a support or as a mechanical barrier (see appended table) Temperature rise of windings (see appended table) arts not subject to a limit under to (see appended table) 7.2 Softening temperature of insulating material supporting parts conductively connected to the mains carrying a current > 0,2 A at least 150 o C henolic bobbin material used for transformers and line filters were acceptable without further test. rimary connector not considered as such part. 8 Constructional requirements with regard to the protection against electric shock 8.1 Conductive parts covered by lacquer, paper, untreated textile oxide films and beads etc. considered to be bare 8.2 No shock hazard when changing voltage setting device, fuse-links or handling drawers etc. 8.3 Insulation of hazardous live parts not provided by hygroscopic material 8.4 No risk of electric shock from accessible parts or from parts rendered accessible following the removal of a cover which can be removed by hand Considered. No such devices or parts intended to be operated by hand. No such material used. No such removable covers. 8.5 Class I equipment Class II equipment. Basic insulation between hazardous live parts and earthed accessible parts Resistors bridging basic insulation complying with 14.1 a) Capacitors bridging basic insulation complying with a) rotective earthing terminal 8.6 Class II equipment and Class II constructions within Class I equipment Double or reinforced insulation between hazardous live parts and accessible parts Components bridging double or reinforced insulation complying with 14.1 a) or 14.3 Basic insulation bridged by components complying with Basic and supplementary insulation each being bridged by a capacitor complying with a) Class II equipment. Reinforced or double insulation provided between primary circuits and secondary circuits in power supply board unit and between live parts and accessible surface.

12 age 10 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Double or reinforced insulation being bridged with 2 capacitors in series complying with a) Double or reinforced insulation being bridged with a single capacitor complying with b) Approved Y1 capacitors used. 8.7 This clause is void 8.8 Basic or supplementary insulation > 0,4 mm (mm) : Bobbin of T831: 0.8 mm ; Bobbin of T901: 0.6 mm. Reinforced insulation > 0,4 mm (mm)... : Thin sheet insulation (excluding non-separable thin sheet insulation. See 8.22) Basic or supplementary insulation, at least two layers, each meeting 10.3 Basic or supplementary insulation, three layers any two of which meet 10.3 Reinforced insulation, two layers each of which meet 10.3 Reinforced insulation, three layers any two which meet Adequate insulation between internal hazardous live conductors and accessible parts Adequate insulation between internal hazardous live parts and conductors connected to accessible parts 8.10 Double insulation between conductors connected to the mains and accessible parts. Double insulation between internal hazardous live parts and conductors connected to accessible parts. Approved optocoupler and insulation sheet under power supply board used. See appended table 14 for details. Insulating tape in transformer T831. Reinforced insulation provide for VC insulated primary wire which has a thickness of at least 0.4mm. Secondary wires to signal board are fixed far away from hazardous live parts. Insulation only for correct function. Approved supply cord used Detaching of wires No undue reduction of creepages or clearance distances if wires become detached Vibration test carried out... : No 8.12 This clause is void 8.13 Adequate fastening of windows, lenses, lamp covers etc. (pull test 20 N for 10 s) 8.14 Adequate fastening of covers (push/pull test 50 N for 10 s) 8.15 No risk of damage to the insulation of internal wiring due to hot parts or sharp edges No such component. For back cover. Wires or cables are fixed well so as to avoid such hazards.

13 age 11 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 8.16 Only special supply equipment can be used Not such equipment Insulated winding wire without additional interleaved insulation Approved triple insulation winding wire used in T902. Insulating tape used between the interleaved windings Endurance test as required by Disconnection from the mains The MAINS plug on supply cord used Disconnect device See above All-pole switch or circuit breaker with >3mm contact separation MAINS switch not considered as disconnection device Mains switch ON indication 8.20 Switch not fitted in the mains cord MAINS switch mounted on the bracket Bridging components comply with clause Non-separable thin sheet material 9 Electric shock hazard under normal operating conditions 9.1 Testing on the outside For voltages >1000 V ac or >1500 V dc complies with clause for basic insulation No such high hazardous voltage a) Open circuit voltages See below b) Touch current measured from terminal devices using the network in annex D... : The open-circuit voltage of the apparatus exceeds 60Vd.c. or 35Vpeak and the touch current measurement was conducted. Refer the test results in appended table. c) Discharge not exceeding 45 μc d) Energy of discharge not exceeding 350 mj Test with test finger and test probe No hazardous live shafts of knobs, handles or levers No knobs, handles or levers are hazardous live Ventilation holes and other holes tested by means of 4 mm x 100 mm test pin Terminal devices tested with 1 mm x 20 mm test pin (10 N); test probe D of IEC Terminal devices tested with 1 mm x 100 mm straight wire (1 N); test probe D of IEC re-set controls tested with 2.5 mm x 100 mm test pin (10 N); test probe C of IEC Compliance is checked. Compliance is checked. Applied to antenna and all input/output signal connectors.

14 age 12 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict No shock hazard due to stored charge on withdrawal of the mains plug; voltage (V) after 2 s : 2s after withdrawal of the mains plug, the pins of the plug is not hazardous live. The measured voltage is 24V. If one bleeder resistance opened, the measured voltage is 26V. If C is not greater than 0,1 μf no test needed See above Resistance to external forces See below a) Test probe 11 of IEC for 10 s (50 N) No hazards. b) Test hook of fig. 4 for 10 s (20 N) No hazards. c) 30 mm diameter test tool for 5 s (100 or 250 N) 9.2 No hazard after removing a cover by hand No removable cover by hand. 10 Insulation requirements 10.1 Insulation resistance (MΩ) at least 2 MΩ min. after surge test for basic and 4 MΩ min. for reinforced insulation... : 100MΩ between main plug and tuner after surge test Humidity treatment 48 h or 120 h... : 30 C, humidity 93%, 48h Insulation resistance and dielectric strength between mains terminals Insulation Resistance and dielectric strength across BASIC or SULEMENTARY insulation (Class I) Insulation resistance and dielectric strength across REINFORCED insulation (Class II) (see appended table) (see appended table) 11 Fault conditions 11.1 No shock hazard under fault condition 11.2 Heating under fault condition No flame, solder soften or became fluid during tests. Flames extinguish within 10 seconds No hazard from softening solder Soldered terminations not used as protective mechanism Measurement of temperature rises (see appended table) Temperature rise of accessible parts (see appended table) Temperature rise of parts, other than windings and printed boards, providing electrical insulation Temperature rise of parts acting as a support or mechanical barrier (see appended table) (see appended table) Temperature rise of windings (see appended table)

15 age 13 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Temperature rise of printed boards shall not exceed the limits of table 3 by max. 100 K for max. 5 min rinted circuit boards (CB) classified as V-0 according to or Clause G.1 may exceed the limit in table 3 in case a) and b): a) Temperature rise of printed circuit boards exceeding the limits of table 3 by not more than 100 K for an area not greater than 2 cm²... : b) Temperature rise of printed circuit boards exceeding the limits of table 3 up to 300 K for an area not greater than 2 cm² for a maximum of 5 min Meets all the special conditions if conductors on printed circuit boards are interrupted Class I protective earthing maintained Temperature rise of parts not subject to the limits of to shall not exceed the limits in table 3, item e), "Fault conditions". Not exceed the values in given in table 3. (see appended table) 12 Mechanical strength Bump test where mass >7 kg The mass of the EUT is more than 7.0kg Vibration test Impact hammer test 3 blows with 0.5J applied to every point of weak part of the exterior. Steel ball test 2J for non-ventilated solid areas of enclosure Drop test for portable apparatus where mass 7 kg Thermoplastic enclosures stress relief test A sample consisting of the complete apparatus is subjected in a circulating air oven to a temperature 70 C, after the test, no hazardous live parts can be accessible Fixing of knobs, push buttons, keys and levers 50N pulling force used on main switch Remote controls with hazardous live parts No hazardous live parts within remote control Drawers (pull test 50 N, 10 s) No such components Antenna coaxial sockets providing isolation No such components Telescoping or rod antennas construction No such components Telescoping or rod antennas securement No such components.

16 age 14 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 13 Clearances and creepage distances 13.1 Clearances in accordance with 13.3 See clause 13.3 Creepage distances in accordance with 13.4 See clause Determination of working voltage Test voltage is AC 240V, see appended table 13.3 Clearances See appended table General See below Circuits conductively connected to the mains comply with table 8 and, where applicable, table 9... : Circuits not conductively connected to the mains comply with table 10 See appended table Measurement of transient voltages 13.4 Creepage distances See appended table Creepage distances greater than table 11 minimum values See appended table 13.5 rinted boards No such printed boards Clearances and creepage distances between conductors on printed circuit boards, one of which may be conductively connected to the mains, as in fig Type B coated printed circuit boards complying with IEC (basic insulation only) 13.6 Conductive parts along uncemented joints clearances and creepage distances comply with 13.3 and 13.4 Conductive parts along reliably cemented joints comply with 8.8 Temperature cycle test and dielectric strength test 500V test for transformers, magnetic coupler and similar devices, if insulation is relied upon for safety 13.7 Enclosed, enveloped or hermetically sealed parts not conductively connected to the mains, clearances and creepage distances as in table arts filled with insulating compound, meeting the requirements of 8.8 Optocouplers are approved component. (see sub-clause 14.11). Optocouplers are approved component. (see sub-clause 14.11). No such devices. Optocoupler used in power supply board. See appended table Components 14.1 Resistors

17 age 15 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict a) Resistors between hazardous live parts and accessible metal parts b) Resistors, other than between hazardous live parts and accessible parts No such construction No such construction Resistors separately approved... : No such resistors Capacitors and RC units See below. Capacitors separately approved : Yes see table Y capacitors tested to IEC , 2 nd edition : X capacitors tested to IEC , 2 nd edition : Capacitors operating at mains frequency but not connected to the mains: tests for X2... : Capacitors with volume exceeding 1750 mm³, where short-circuit current exceeds 0,2 A: compliance with IEC , 4.38 category B or better... : Capacitors with volume exceeding 1750 mm³, mounted closer to a potential ignition source than table 5 permits: compliance with IEC , 4.38 category B or better... : Shielded by a barrier acc. to / table 21 or metal... : Approved Y1 capacitors used in power supply board. Approved X2 capacitors used in power supply board. No such X2 capacitors used The main fuse will break when short-circuit the capacitors after main fuse. No possibility of flammability. Capacitors C860 and C865 with metal enclosure No such capacitors used 14.3 Inductors and windings See below. Comply with IEC , IEC (as relevant) and clause Transformers and inductors marked with manufacturer's name and type... : Transformers and inductors separately approved. : Tested in equipment. See appended table. Transformers and inductors are tested within the equipment General See below. Insulation material complies with clause Constructional requirements See below Clearances and creepage distances comply with clause 13 See appended table Transformers meet the constructional requirements Compliance is checked by inspection Separation between windings See below Class II transformers have adequate separation between hazardous live parts and accessible parts (double or reinforced insulation)... : Coil formers and partition walls > 0,4 mm Compliance with double or reinforced insulation. See appended table.

18 age 16 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Class I transformers, with basic insulation and protective screening only if all 7 conditions of are met Separating transformers with at least basic insulation Insulation between HAZARDOUS LIVE parts and ACCESSIBLE parts Class II transformers have adequate insulation between hazardous live parts and accessible parts (double or reinforced insulation) Coil formers and partition walls > 0,4 mm Class I transformers have adequate insulation between hazardous live parts and accessible conductive parts or those conductive parts or protective screens connected to a protective earth terminal Winding wires connected to protective earth have adequate current-carrying capacity No such construction. No such construction. Compliance with double or reinforced insulation. See appended table. No such construction. No such construction High voltage components All components operating voltage is below 4kV. High-voltage components and assemblies: U > 4 kv (peak) separately approved Component meets category V-1 of IEC High voltage transformers and multipliers tested as part of the submission High voltage assemblies and other parts tested as part of the submission 14.5 rotective devices Approved fuse used rotective devices used within their ratings External clearances and creepage distances meet requirement of clause 13 for the voltage across the device when opened a) Thermal cut-outs separately approved No such component. b) Thermal cut-outs tested as part of the submission No such component a) Thermal links separately approved No such component. b) Thermal links tested as part of the submission No such component Thermal devices re-settable by soldering No such component Fuse-links in the mains circuit according to IEC See appended table Correct marking of fuse-links adjacent to holder... : F801 T 6.3A L 250V Not possible to connect fuses in parallel... : Not possible to touch hazardous live parts when replacing fuse-links without the use of a tool... : The fuse cannot be replaced without the use of a tool.

19 age 17 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict TC thermistors comply with IEC :2007 No such components. TC devices (15 W) category V-1 or better Circuit protectors have adequate breaking capacity and their position is correctly marked 14.6 Switches (see appended table) a) Separate testing to IEC including: operations - Normal pollution suitability - Make and break speed independent of speed of actuation V-0 compliance with annex G, G.1.1 An approved switch used and comply the relevant standard b) Tested in the apparatus: Switch controlling > 0.2A with open contact voltage > 35 V (peak)/24 V dc complying with , and V-0 in annex G, G.1.1 Switch controlling > 0.2A with open contact voltage < 35 V (peak)/24 V dc complying with and V- 0 in annex G, G.1.1 Switch controlling < 0.2A with open contact voltage > 35 V (peak)/24 V dc complying with and V-0 in annex G, G Switch tested to b) constructed to IEC subclause 13.1 and has making/breaking action independent of speed of actuation Switch tested to b) compliant with IEC subclause d) and m) not attaining excessive temperatures in use Switch tested to b) has adequate dielectric strength Mains switch controlling mains socket outlets additional tests to IEC Socket outlet current marking correct 14.7 Safety interlocks No such component. Safety interlocks to 2.8 of IEC Voltage setting devices and the like No such component. Voltage setting device not likely to be changed accidentally 14.9 Motors No such component Endurance test on motors Motor start test Dielectric strength test

20 age 18 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Not adversely affected by oil or grease etc rotection against moving parts Motors with phase-shifting capacitors, three-phase motors and series motors meet clause. B.8, B.9 and B.10 of IEC , Annex B Batteries No such component Batteries mounted with no risk of accumulation of flammable gases No possibility of recharging non-rechargeable batteries Recharging currents and times within manufacturers limits Lithium batteries discharge and reverse currents within the manufacturers limits Battery mould stress relief Battery drop test Optocouplers Approved optocoupler used. See appended table 14. a) Comply with 13.6 (jointed insulation) and N.2.1 b) Comply with IEC :2007 Alternative to a) and b) optocoupler comply with Surge suppression varistors Certified sources of varistors are used. For details, see appended able 14. Comply with IEC Not connected between mains and accessible parts except for earthed parts of permanently connected apparatus Complies with the current pulse, fire hazard and thermal stress requirements of Not connected to accessible parts/output circuits. Certified sources with suitable characteristics used. 15 Terminals Mains plug, appliance inlet, interconnection couplers and mains socket-outlet meet the appropriate standard Overloading of plugs or appliance inlets prevented if the apparatus has mains socket outlets Overloading of internal wiring prevented if the apparatus has mains socket outlets MAINS plug and appliance couplers certified according to relevant standard. See attached table Connectors for antenna, earth, audio, video or data

21 age 19 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict No risk of insertion in mains socket-outlets No risk of insertion into audio- or video- outlets marked with the symbol of Output terminals of a.c. adaptors or similar devices not compatible with household mains socket-outlets No such connectors rovision for protective earthing Accessible conductive parts of Class I equipment reliably connected to earth terminal, within equipment rotective earth conductors correctly coloured Equipment with non-detachable mains cord provided with separate protective earth terminal near mains input rotective earth terminal resistant to corrosion Earth resistance test: < 0,1 at 25 A... : 15.3 Terminals for external flexible cords and for permanent connection to the mains supply Adequate terminals for connection of permanent wiring Reliable connection of non-detachable cords Not soldered to conductors of a printed circuit board AC inlet used. Adequate clearances and creepage distances between connections should a wire break away Wire secured by additional means to the conductor Screws and nuts clamping conductors have adequate threads: ISO 261, ISO 262 or similar Soldered conductors wrapped around terminal prior to soldering or held in place by additional means Clamping of conductor and insulation if not soldered or held by screws Terminals allow connection of appropriate crosssectional area of conductors, for the rated current of the equipment No screws for such use Terminals to have sizes required by table Terminals clamp conductors between metal and have adequate pressure Terminals designed to avoid conductor slipping out when tightened or loosened Terminals adequately fixed to avoid loosening when the clamping is tightened or loosened and stress on internal wiring is avoided

22 age 20 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Terminals carrying a current more than 0,2 A: contact pressure not transmitted by insulating material except ceramic Termination of non-detachable cords: wires terminated near to each other Terminals located and shielded: test with 8 mm strand 15.4 Devices forming a part of the mains plug Not such apparatus No undue strain on mains socket-outlets Device complies with standard for dimensions of mains plugs Device has adequate mechanical strength (tests a,b,c) 16 External flexible cords 16.1 Mains cords sheathed type, complying with IEC for VC or IEC for synthetic rubber cords... : Non-detachable cords for Class I have green/yellow core for protective earth 16.2 Mains cords conductors have adequate crosssectional area for rated current consumption of the equipment 16.3 a) Flexible cords not complying with 16.1, used for interconnections between separate units of equipment used in combination and carrying hazardous live voltages, have adequate dielectric strength b) Flexible cords not complying with 16.1, withstand bending and mechanical stress (3.2 of IEC ) 16.4 Flexible cords used for connection between equipment have adequate cross-sectional areas to avoid temperature rise under normal and fault conditions VC complying with IEC mm 2 supply cord used for the apparatus Adequate strain relief on external flexible cords AC inlet used. Not possible to push cord back into equipment Strain relief device unlikely to damage flexible cord For mains cords of Class I equipment, hazardous live conductors become taut before earth conductor 16.6 Apertures for external flexible cord: no risk of damage to the cord during assembly or movement in use

23 age 21 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 16.7 Transportable musical instruments and amplifiers fitted with detachable cord set with appliance inlet to IEC Transportable musical instruments and amplifiers fitted with detachable cord sets or with means of stowage to protect the cord 17 Electrical connections and mechanical fixings 17.1 Torque test to table 20 - screws into metal: 5 times Screw for fixing stand (Φ4.0mm) and back cover (Φ3.0mm). - screws into non-metallic material: 10 times Screw for fixing back cover (Φ3.0mm) Correct introduction into female threads in nonmetallic material 17.3 Cover fixing screws: captive Non-captive fixing screws: no hazard when replaced by a screw whose length is 10 times its diameter 17.4 No loosening of conductive parts carrying a current > 0,2 A 17.5 Contact pressure not transmitted through plastic other than ceramic for connections carrying a current > 0,2 A 17.6 Stranded conductors of flexible supply cords carrying a current > 0,2 A with screw terminals not consolidated by solder 17.7 Cover fixing devices other than screws have adequate strength and their positioning is unambiguous 17.8 Fixing devices for detachable legs or stands provided 17.9 Internal pluggable connections, affecting safety, unlikely to become disconnected No such terminals Cover fixed by screws only. ull with 2N force. No disconnection. 18 Mechanical strength of picture tubes and protection against the effects of implosion 18.1 icture tube separately approved to IEC : icture tube separately approved to : 18.2 Non-intrinsically protected tubes tested to Stability and mechanical hazards

24 age 22 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Mass of the equipment exceeding 7 kg... : 13.0 kg with stand Apparatus intended to be fastened in place suitable instructions... : 19.1 Test on a plane, inclined at 10 o to the horizontal Not overturn N force applied vertically downwards N force, or 13% of weight, applied horizontally to point of least stability Not exceed 25 kg in weight. And below 1m in height Edges or corners not hazardous No sharp edges and corner 19.5 Glass surfaces (exc. laminated) with an area exceeding 0,1 m² or maximum dimension > 450 mm, pass the test of No such parts Wall or ceiling mountings adequate No accessories for wall or ceiling mounting provided. 20 Resistance to fire 20.1 Electrical components and mechanical parts a) Exemption for components contained in an enclosure of material V-0 to IEC with openings not exceeding 1 mm in width b) Exemption for small components as defined in Electrical components meet the requirements of Clause 14 or Insulation of internal wiring working at voltages > 4 kv or leaving an internal fire enclosure, or located within the areas mentioned in Table 21, not contributing to the spread of fire Material of printed circuit boards on which the available power exceeds 15 W at a voltage between 50 V and 400 V (peak) a.c. or d.c. meets V-1 or better to IEC 60707, unless used in a fire enclosure Material of printed circuit boards on which the available power exceeds 15 W at a voltage >400 V (peak) a.c. or d.c. meets V-0 to IEC Components and parts not covered by , and (other than fire enclosures) mounted nearer to a potential ignition source than the distances in Table 21 comply with the relevant flammability category in Table 21 Components and parts as above but shielded from a potential ignition source, with the barrier area in accordance with Table 21 and fig. 13 Components are used correctly within their ratings and comply with the relevant flammability requirement. See appended table 14. No such internal wiring. All used CB comply with UL approved flammability class of 94 V-0. (See table 14). Same as above. Min. flammability class for transformer and line choke are V-0. See appended table 14.

25 age 23 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Apparatus with voltages >4kV under normal operating conditions and distances to the enclosure exceed those specified Table 21, flammability classification HB40 or better is required for the enclosure 20.2 Fire enclosure otential ignition sources with open circuit voltage > 4 kv (peak) a.c. or d.c. contained in a fire enclosure to V Internal fire enclosures with openings not exceeding 1 mm in width and with openings for wires completely filled Requirements of and met by an internal fire enclosure No such high voltage within apparatus. Not applied No such internal fire enclosure. A Annex A, Additional requirements for apparatus with protection against splashing water A.5 Marking and instructions No requirements for protection against splashing water during intended use. A.5.1 j) Marked with IX4 (IEC 60529), a) does not apply A.10 Insulation requirements A.10.2 Splash and humidity treatment A Enclosure provides protection against splashing water A Humidity treatment carried out for 7 days B Annex B, Apparatus to be connected to the TELECOMMUNICATION NETWORKS Complies with IEC clause 1 Complies with IEC clause 2 Complies with IEC clause 3 but with modified to of this standard Complies with IEC clause 4 but with 4.1.2, and modified in accordance with annex B of this standard Complies with IEC cause 5 but with modified in accordance with annex B of this standard Complies with IEC clause 6 Complies with IEC clause 7 Not for connection with telecommunication networks.

26 age 24 of 51 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Complies with IEC annex A, B and C L ANNEX L, Additional requirements for electronic flash apparatus for photographic purposes L. 5 Marking and instructions L. 5.4 Instructions for battery chargers and Supply apparatus indicating type or model number of flash apparatus with which it is to be used Instructions for flash apparatus indicating type or model number of battery chargers or Supply apparatus with which it is to be used L. 7 Heating under normal operating conditions L7.1.5 & L Lithium batteries meet permissible temp rise in Table 3, unless comply with or of IEC L. 9 Electric shock hazard under normal operating conditions L Terminals to connection to synchroniser not HAZARDOUS LIVE L.10 Insulation requirements L High frequency puls ignition L. 12 Mechanical strength L Windows for flash tubes are excluded from steel ball impact test L. 14 Components L Mains switch characteristics appropriate to its function under normal conditions L. 20 Resistance to fire L c) Trigger coil for discharge purpose is not considered to be a OTENTIAL IGNITION SOURCE

27 age 25 of 51 Report No.: TABLE: temperature rise measurements: ower consumption in the OFF/Stand-by mode of the functional switch (W)... : 0W/ 0.51W max. Cond. Un (V) Hz In (A) n (W) Uout (V) out (W) Operating Condition / Status Max. normal load with 1/8 non-clipped max. audio output power ATV mode AV mode Ybr mode HDMI mode ATV mode ATV mode ATV mode Max. normal load with max. non-clipped audio output power ATV mode ATV mode ATV mode ATV mode Loudspeaker impedance (Ω)... : 2*8 Ω Several loudspeaker systems... : Marking of loudspeaker terminals... : Temperature Rise dt of art dt (K) Limit max dt (K) Test Condition No. No 8 No 11 No _- EUT ower supply cord rimary wire after main switch LCD panel surface (front) LCD panel surface (back) Back enclosure above the power supply(internal part) Back enclosure above the power supply(external part) For reference Button of main switch ower supply board AC inlet(x802) close to pins (70-35) L802 winding (130-35) L812 winding (130-35) C813(X2) (85-35) C809 (Y1) (85-35) C860 (Electrolytic) (105-35) Winding of T *(85-10)

28 age 26 of 51 Report No.: Temperature Rise dt of art dt (K) Limit max dt (K) Test Condition No. No 8 No 11 No _- rimary Winding of T *(85-10) Secondary Winding of T *(85-10) Winding of T *(85-10) CB under VB801 and heat sink (120-35) CB under V802 and heat sink (120-35) CB under VD829 and heat sink (120-35) CB under T (120-35) N891(photocoupler) (100-35) Insulation sheet under SU (80-35) Mainboard CB under main chip (120-35) CB under audio amplifier (120-35) Ambient 24.7 C 21.0 C Note(s): 1. Specified maximum ambient temperature for operation is 35 C. 2. ermitted temperature rises were reduced by 10K for switch mode transformer when measured by thermocouple. Winding temperature rise measurements Ambient temperature t1 ( o C)... : Ambient temperature t2 ( o C)... : Temperature rise dt of winding: dt = (R 2 R 1 ) x ( t1) (t2 t1) R 1 R 1 (Ω) R 2 (Ω) dt (K) Limit max (K) Insulation class 7.2 TABLE: softening temperature of thermoplastics Temperature T of part T - normal conditions ( o C) T - fault conditions ( o C) Min T softening ( o C) Note: henolic bobbin material used for transformers and line filters were acceptable without further test. rimary connector not considered as such part TABLE: insulation resistance measurements Insulation resistance R between: R (MΩ) Required R (MΩ) Unit: Between parts of opposite polarity directly connected to the mains poles (with fuse disconnected), (BI) Unit: rimary circuits (L/N) to LCD panel (RI) Unit: rimary circuits (L/N) to accessible surface (RI) Unit: rimary circuits (L/N) to signal connectors (RI) T831/T901: rimary windings to secondary windings (RI) 100 4

29 age 27 of 51 Report No.: Insulation resistance R between: R (MΩ) Required R (MΩ) T831: rimary windings/pins and secondary windings/pins to core and insulation tubing (BI or SI) T901: rimary windings/pins and secondary windings/pins to core (BI or SI) T902: rimary windings and core to secondary windings (RI) T831: Two layers insulation tape (RI) Insulation of primary wire (RI) Insulation sheet under power supply board (RI) Notes: All sources of transformers and insulation sheet were considered in this test TABLE: electric strength measurements Test voltage applied between: Test voltage (V) Breakdown Unit: Between parts of opposite polarity directly connected to the mains poles (with fuse disconnected), (BI) 2120 (peak) No Unit: rimary circuits (L/N) to LCD panel (RI) 4240 (peak) No Unit: rimary circuits (L/N) to accessible surface (RI) 4240 (peak) No Unit: rimary circuits (L/N) to signal connectors (RI) 4240 (peak) No T831/T901: rimary windings to secondary windings (RI) 4240 (peak) No T831: rimary windings/pins and secondary windings/pins to core and insulation tubing (BI or SI) T901: rimary windings/pins and secondary windings/pins to core (BI or SI) 2487 (peak) No 2576 (peak) No T902: rimary windings and core to secondary windings (RI) 4240 (peak) No T831: Two layers insulation tape (RI) 4240 (peak) No Insulation of primary wire (RI) 4240 (peak) No Insulation sheet under power supply board (RI) 4240 (peak) No Notes: All sources of transformers and insulation sheet were considered in this test TABLE: summary of fault condition tests Voltage (V) 0,9 or 1,1 times rated voltage... : See below Frequency (Hz)... : 50 Ambient temperature ( o C)... : ºC otherwise specified. No. Component Fault dt (K) / Component Other results (include description and test duration)

30 age 28 of 51 Report No.: No. Component Fault dt (K) / Component Other results (include description and test duration) 1. Ventilation Blocked T831: 53.9K T901: 47.6K T902: 38.3K CB under VB801: 38.6K CB under VD829: 56.5K N891: 37.0K LCD panel surface: 24.8K Back enclosure: 19.2K Button of main switch: 2.4K Ambient: 22.7 o C Input voltage: 198V Duration: 60 minutes Limit dt (K) 140(150-10) 140(150-10) 140(150-10) 2. One speaker s-c -- Input voltage: 264V Input: 130.8W; Both speakers did not work. The other parts worked as normal. No hazards. Duration: 10 minutes 3. USB output (mainboard) 4. USB output (mainboard) s-c -- Input voltage: 264V o-l T831: 56.3 K T903: 38.3K T902: 28.1K Ambient: 23.8 o C Input: 150.8W 5. C860 s-c -- Input voltage: 264V No input. 6. VB801, Input to output The EUT worked normally except for USB port. No hazards. Duration: 10 minutes Input: 198V Duration: 60 minutes Input: 152.0W Normal operation until overload to 3.5A. No breakdown, no hazards. Limit dt (K): 140(150-10) 140(150-10) 140(150-10) -- Main fuse broken immediately. Then the EUT shut down. No hazards. Duration: <1s s-c -- Input voltage: 264V No input. Main fuse broken immediately. Then the EUT shut down. No hazards. Duration: <1s

31 age 29 of 51 Report No.: No. Component Fault dt (K) / Component Other results (include description and test duration) 7. 12V output (C862) 8. 16V output (C868) s-c -- Input voltage: 264V Input: W The EUT protected immediately. The input changed in a range. No picture/sound signal output. No hazards. Duration: 10 minutes s-c -- Input voltage: 264V Input: W The EUT protected immediately. The input changed in a range. No picture/sound signal output. No hazards. Duration: 10 minutes 9. V807, in 1-2 s-c -- Input voltage: 264V Input: 0.4W R818 broken. Then the EUT shut down. No hazards. Repeat the test 2 times with the same results. Duration: 10 minutes 10. V807, in 1-3 s-c -- Input voltage: 264V Input: 0.2W The EUT protected immediately. No picture/sound signal output. No hazards. Duration: 10 minutes 11. V807, in 2-3 s-c -- Input voltage: 264V Input: 0.4W 12. T831, in T831, in T831, in7-11 s-c -- Input voltage: 264V R818 broken. Then EUT shut down. No hazards. Repeat the test 2 times with the same result. Duration: 10 minutes Input: W The EUT self-protected immediately. The input changed in certain range. No picture/sound signal output. Duration: 10 minutes s-c -- Input voltage: 264V s-c T831:102K Ambient: 22.0 Input: W The EUT self-protected immediately. The input changed in certain range. No picture/sound signal output. Duration: 10 minutes Input voltage: 264V Input: W The EUT self-restart circularly. No hazards. Duration: 60 minutes

32 age 30 of 51 Report No.: No. Component Fault dt (K) / Component Other results (include description and test duration) 15. T831, in8-9/ N891, rimary pins 17. N891, Secondary pins s-c -- Input voltage: 264V Input: W The EUT self-protected immediately. The input changed in certain range. No picture/sound signal output. Duration: 10 minutes s-c -- Input voltage: 264V Input: 0.4W The EUT self-protected immediately. s-c -- Input voltage: 264V No picture/sound signal output. No hazards. Duration: 30 minutes Input: 0.4W The EUT self-protected immediately. 18. N834, pin 8-2 s-c -- Input voltage: 264V 19. V901, in V901, in V901, in 2-3 No picture/sound signal output. No hazards. Duration: 30 minutes Input: 0.3W The EUT self-protected immediately. s-c -- Input voltage: 264V No input. No picture/sound signal output. No hazards. Duration: 10 minutes Main fuse broken immediately. Then the EUT shut down. No hazards. Duration: <1s s-c -- Input voltage: 264V Input: 35.2W s-c -- Input voltage: 264V No input. The EUT had only sound signal output, no picture signal output. No hazards. Duration: 30 minutes Main fuse broken immediately. Then the EUT shut down. No hazards. Duration: <1s 22. T901, in 3-6 s-c -- Input voltage: 264V Input: 35.4W The EUT had only sound signal output, no picture signal output. No hazards. Duration: 10 minutes

33 age 31 of 51 Report No.: No. Component Fault dt (K) / Component Other results (include description and test duration) 23. T901, in T902, in T902, in T902, in X901 output (for LED backlight) L1+ to L1- s-c -- Input voltage: 264V Input: 36.0W s-c -- Input voltage: 264V The EUT had only sound signal output, no picture signal output. No hazards. Duration: 10 minutes Input: 35.8W s-c -- Input voltage: 264V The EUT had only sound signal output, no picture signal output. No hazards. Duration: 10 minutes Input: 35.6W s-c -- Input voltage: 264V The EUT had only sound signal output, no picture signal output. No hazards. Duration: 10 minutes Input: 35.4W s-c -- Input voltage: 264V The EUT had only sound signal output, no picture signal output. No hazards. Duration: 10 minutes Input: 35.4W The EUT had only sound signal output, no picture signal output. No hazards. Duration: 10 minutes Winding temperature rise measurements Ambient temperature t1 ( o C)... : Ambient temperature t2 ( o C)... : Supplementary information: In fault column, where s-c=short circuit and o-l=over load TABLE: working voltage measurement Location RMS Voltage (V) eak Voltage (V) Comments Transformer T901 pin3 - pin pin6 - pin pin3 - pin pin6 - pin pin3 - pin Max. Vpeak&Vrms pin6 - pin Transformer T831 pin1 to pin 7/ pin3 to pin 7/ pin5 to pin 7/ pin6 to pin 7/

34 age 32 of 51 Report No.: pin1 to pin 9/ Max. Vpeak&Vrms pin3 to pin 9/ pin5 to pin 9/ pin6 to pin 9/ pin1 to pin 11/ pin3 to pin 11/ pin5 to pin 11/ pin6 to pin 11/ Transformer T902 pin1 to pin pin1 to pin Max. Vpeak&Vrms pin1 to pin pin1 to pin pin5 to pin pin5 to pin pin5 to pin pin5 to pin pin7 to GND pin9 to GND Other components C909 pin+ to pin N891 pin Supplementary information: 240V supplied & 13.4 TABLES: Clearances and Creepage distances Rated supply voltage: 240V a.c. ollution degree.. : 2 Material Group... : IIIb 2 N force on internal parts applied: -- Yes 30 N force on outside of conductive enclosure applied: -- Location Working Voltage Clearance (mm) Creepage (mm) V rms V peak Min Actual Min Actual L/N before fuse (BI) 250* 420* Trace between fuse (BI) 250* 420* rimary to secondary (RI) See below See below - Under C803, C * 420* Under C * 420* Under N891, N * 420* Under T831 (Trace of N891 primary to secondary) 250* 420* Under T901 (Trace of T902 pin 9 to GND) 250* 420* Under T * 420* Circuits conductively connected to the mains (use Tables 8, 9 and 11): see note below.

35 age 33 of 51 Report No.: Location Working Voltage Clearance (mm) Creepage (mm) V rms V peak Min Actual Min Actual Notes: 1. For clearance and creepage did not describe above are far larger than limit above. "Min" = minimum required. "Actual = Actual dimensions measured. 2. Data with * means the measured data not more than this data. 3. 2N force applied on relevant components during the distance test. 4. Component fixed by glue on the CB: RV801, RT801, C860, C862, C865 etc. 5. For clearance and creepage of transformers T831, T901 and T902 please refer to the table and TABLE: list of critical components and materials Component ower supply board -CB -AC inlet (X802) -rimary connector (X803) Manufacturer/ trademark Hisense Electric Co., Changzhou Aohong Electronics Co., Ltd Type/model Value / rating Standard Approval/ Reference HLL-4855WF Input: AC V, 50/60Hz, 3A Max; output: DC12V, 3A; DC16V, 1.5A; DC200V 400mA. AOH-2 V-0, 1.5mm Min. Thick, 130 C. Interchangeable Interchangeable V-0, 1.5mm Min. Thick, 120 C min. Zhang Jiagang Huajie Electronic Co., Ltd Zhang Jiagang Huajie Electronic Co., Ltd Zhang Jiagang Huajie Electronic Co., Ltd Zhe Jiang Bei Er Jia Electronic Co., Zhe Jiang Bei Er Jia Electronic Co., TECX-UNIONS ELECTRONIC CO., Ltd Shanghai Hua Yi Group Hua Yuan Chemical Industry Co Ltd SA-2S-127; SA- 2S-129; SA-2S- 165 SA-2S C; SA-2S D; SA-2S D1; SA-2S E; SA-2S C-2 SA-2S H; SA-2S L; SA-2S J; SA- 2S K; SA-2S M; SA-2S N 250V AC, 2.5A 70 C, standard sheet C8 250V AC, 2.5A 70 C, standard sheet C8 250V AC, 2.5A 70 C, standard sheet C8 ST-A V AC, 2.5A 70 C, standard sheet C8 ST-A ST-A ST-A V AC, 2.5A 70 C, standard sheet C8 SO V AC, 2.5A 70 C, standard sheet C8 IEC/EN UL 94 UL 796 UL 94 UL 796 A66 FR-102 V-0 UL 94 IEC Tested with equipment UL E UL IEC/EN TUV R IEC/EN TUV R IEC/EN TUV R IEC/EN NEMKO /A1 IEC/EN ENEC ENEC VDE IEC/EN VDE UL E & Tested with equipment

36 Component Manufacturer/ trademark age 34 of 51 Report No.: Type/model Value / rating Standard Approval/ Reference Interchangeable Interchangeable V-0 UL 94 UL -Fuse (F801) Littelfuse Inc. 382 T6.3AL, AC 250V -VDR (RV801) XC Electronics (Shenzhen) Corp. Conquer Electronics Co., Suzhou Walter Electric Co., Ltd Thinking Electronic lndustrial Co., Thinking Electronic lndustrial Co., 5TR MET T6.3AL, AC 250V T6.3AL, AC 250V 2000 T6.3AL, AC 250V TVR10621-V TVR10621-D 620V, fulfil with IEC Annex Q 620V, fulfil with IEC Annex Q ECOS OHG S10KV621E2K1 620V, fulfil with IEC Annex Q -Filter (L801, L802) Shaanxi Huaxing electronic group Co., Jiangsu Lettall Electronic Co., Haining Lianfeng Dongjin Electronic Co., Dezhou Sanhe Electric Co., Weihai Dongxing Electronics Co., Shandong Zhongrui Electronics Co., Jiangsu Huaxing Electric Co., Ltd -- bobbin Changchun lastics Co., MYG20G10K V, fulfil IEC Annex Q IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN VDE VDE VDE VDE VDE VDE VDE VDE LCL-3505-HF 130 C IEC/EN Tested with equipment LCL-010-F 130 C IEC/EN Tested with equipment LCL C IEC/EN Tested with equipment LCH C IEC/EN Tested with equipment ZRI C IEC/EN Tested with equipment LCL-2505D C IEC/EN Tested with equipment T375J henolic, 150 C, V-0 -- (Alternative) Interchangeable Interchangeable henolic, 150 C; V-0 UL 94 UL 94 UL E59481 UL

37 Component Manufacturer/ trademark age 35 of 51 Report No.: Type/model Value / rating Standard Approval/ Reference -NTC (RT801) Interchangeable Interchangeable 5Ω at 25 C UL 1434 UL -Bleeder resistor (R802, R804, R809 R970, R971 R972) -X2 Capacitor ( C813,C846) -Electrolytic capacitor (C860, C865) -Y1 Capacitor (C803, C804, C809) Interchangeable Interchangeable 1MΩ, 1/4W IEC/EN Tested with equipment Xiamen Faratronic Co., Xiamen Faratronic Co., Nanjing Tengen Rongguangda Electronics (Group) Co., Uitra Tech Xiphi Enterprise Co., Guangdong Fengming Electronic Tech. Co., MK62 MK61 MK HQX MK-X2 0.47μFmax., AC 275V,110 C 0.47μF max., AC 275V,100 C 0.47μF max., AC 275V, 100 C 0.47μF max., AC 275V, 100 C 0.47μF max., AC 275V, 85 C Interchangeable Interchangeable 68μF, 450V min., 105 C Anshan Electronic Ceramic Co., TDK Xiamen Co., Yinan Don s Electronic Component Co., Guangdong South Hongming Electronic Science and Technology Co., CT7 CD CT81 F C803=C804= 470pF max, C809= 1000pF max., AC250V min., 85 C C803=C804= 470pF max, C809=1000pF max., AC250V min., 85 C C803=C804= 470pF max, C809=1000pF max., AC250V min., 125 C C803=C804= 470pF max, C809=1000pF max., AC250V min., 125 C IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN VDE VDE VDE VDE VDE Tested with equipment VDE VDE VDE VDE

38 Component -Transformer (T831) Manufacturer/ trademark Murata Manufacturing Co., Kunshan Wansheng Electronics Co., Jiangsu Lettall Electronic Co., Dezhou Sanhe Electric Co., Haining Lianfeng Dongjin Electronic Co., Weihai Dongxing Electronics Co., Yueqing Jingmi Electron Electronic Co., age 36 of 51 Report No.: Type/model Value / rating Standard Approval/ Reference KX CT7 BK-10-05HI C803=C804= 470pF max, C809=1000pF max., AC250V min., 125 C C803=C804= 470pF max., C809=1000pF max., AC250V min., 125 C Class B,refer to table & for details IEC/EN IEC/EN IEC/EN IEC SANHE Same as above IEC/EN IEC BCK-70-05HI Same as above IEC/EN IEC BCK-EFD-3333 Same as above IEC/EN IEC XW40EFD2- B19H015 Same as above IEC/EN IEC Windings Interchangeable Interchangeable 130 C UL 1446 UL -- Bobbin Sumitomo Bakelite Co., (Alternative) (Alternative) Chang Chun lastics Co., --Insulation tape Yahua ressure Sensitive Glue Co., --Margin tape M-9820 T375J henolic, 150 C; V-0 henolic, 150 C; V-0 Interchangeable Interchangeable henolic, 150 C; V-0 Yahua ressure Sensitive Glue Co., CT WF 130 C, flame retardant, CTI 400 min, material group II min. 130 C, flame retardant, CTI 400 min. material group II min. --Tubing Interchangeable Interchangeable 200 C, 600V, VW-1 UL 94 UL 94 UL 94 UL 510 UL 510 UL 224 VDE VDE Tested with equipment Tested with equipment Tested with equipment Tested with equipment Tested with equipment UL E41429 UL E59481 UL UL E UL E UL

39 Component -Transformer (T901) Manufacturer/ trademark Haining lianfeng Dongjin Electronic Co., Weihai Dongxing Electronics Co., Jiangsu Lettall Electronics Co., Yueqing Jingmi Electron Electronic Co., Dezhou Sanhe Electric Co., age 37 of 51 Report No.: Type/model Value / rating Standard Approval/ Reference BCK-70-H012 Class B,refer to table & for details IEC/EN IEC BCK-EFD-3538 Same as above IEC/EN IEC BK-20-12HE Same as above IEC/EN IEC XW40EFD2- A34H012 Same as above IEC/EN IEC SANHE Same as above IEC/EN IEC Windings Interchangeable Interchangeable 130 C UL1446 UL -- Bobbin Sumitomo Bakelite Co., (Alternative) (Alternative) Chang Chun lastics Co., --Insulation tape Yahua ressure Sensitive Glue Co., M9820 T375J henolic, 150 C; V-0 henolic, 150 C; V-0 Interchangeable Interchangeable henolic, 150 C; V-0 CT 130 C, flame retardant, --Insulating tape Interchangeable Interchangeable 130 C, flame retardant -Transformer (T902) Weihai Dongxing Electronics Co., Yueqing Jingmi Electron Electronic Co., Jiangsu Lettall Electronics Co., Haining Lianfeng Dongjin Electronic Co., Dezhou Sanhe Electric Co. BCK XW2025EC- B05H003 Class B,refer to table & for details UL 94 UL 94 UL 94 UL 510 UL 510 IEC/EN IEC Same as above IEC/EN IEC BK-10-05YG Same as above IEC/EN IEC BCK Same as above IEC/EN IEC SANHE Same as above IEC/EN IEC ri. Windings Interchangeable Interchangeable 130 C UL1446 UL Tested with equipment Tested with equipment Tested with equipment Tested with equipment Tested with equipment UL E41429 UL E59481 UL UL E UL Tested with equipment Tested with equipment Tested with equipment Tested with equipment Tested with equipment

40 Component --Sec. windings --Bobbin Manufacturer/ trademark FURUKAWA ELECTRIC CO LTD Shanghai Lucy Trade Co., age 38 of 51 Report No.: Type/model Value / rating Standard Approval/ Reference TEX-E TIW-B 130 C, triple insulation wire 130 C, triple insulation wire Interchangeable Interchangeable henolic, 150 C; V-0 --Insulating tape Interchangeable Interchangeable 130 C, flame retardant --Tubing Interchangeable Interchangeable 200 C, 600V, VW-1 -hotocoupler (N881, N891) Main signal board Everlight Electronics Co., VISHAY Semiconductour GmBH Lite-On Technology Corporation EL817 VO617A-3 LTV-817 Int.=6.0mm, Ext.=7.7mm, dti. 0.5mm, 110 C Int.=5.8mm, Ext.=7.0mm, dti. 0.6mm, 100 C Int.=5.2mm, Ext.=7.8mm, dti. 0.8mm, 110 C UL 2353 IEC/EN IEC/EN UL 2353 IEC/EN IEC/EN UL 94 UL 510 UL 224 IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN Main IC MediaTek.Inc MTK UL E VDE UL E VDE UL UL UL DEMKO D A1 FIMKO NCS/FI A1 Intertek CB Others LCD panel Insulation sheet under power supply board (Alternative) Main switch Interchangeable Interchangeable V-0, 1.6mm min. thick, 120 C min. Hisense Electric Co., Suzhou Omay Optical Materials Co., Chengdu Kanglongxin lastics Co., Zhangjiagang Huafeng Electronic Connector & Component Co., HD500DU-B53 SE42B KLX FRC- 870B or KLX FRC- 1880B HF-606(TV)- HF-606(TV)-S 50 inch TFT LCD with LED backlight. The max. power consumption for signal part is 30.6W C, 0.5mm thick, V-0, 80 C C, 0.5mm thick, V-0, 80 C Rocker switch, TV-5, 8A/128A AC 250V, T85/55, 10E3, Level 3 UL 94 UL 796 IEC/EN UL 94 UL 94 UL Tested with equipment UL E UL E IEC/EN VDE TUV R

41 Component (Alternative) (Alternative) (Alternative) (Alternative) Manufacturer/ trademark Zhangjiagang Huajie Electronic Zhejiang Zhongxun Electronics Co., Ltd Zhejiang LECI Electronics Co., ZheJiang Beierjia Electronics Co., Ltd age 39 of 51 Report No.: Type/model Value / rating Standard Approval/ Reference S8 Rocker switch, 6(4)A, AC 250V, 5E4, T85/55, Level 3 KCD (6)A or 6/12A AC 250V, 1E4, T55 RS601D 6(4)A, AC 250V, 1E4, T55, Level 3; 8A/128A, AC 250V, 1E4, T55. S8A-11 Rocker switch, 12(4)A, AC 250V, 10E3, T55 rimary wire Interchangeable AWM1672 VW-1, 105 C, 300V, 20AWG, reinforced insulation Insulating cap on main switch Main lug (Alternative) (Alternative) Interchangeable Interchangeable C, 0.7mm thick, V-0 Shanghai Yusheng Enterprise Development Co., I-Sheng Electric Wire & Cable Co., Shenzhen Xiekang Electric Co., IEC/EN VDE TUV R IEC/EN TUV R IEC/EN VDE TUV R IEC/EN VDE UL 758 UL 94 YS-2 AC 250V,16A VDE VDE S-026A AC 250V,16A VDE VDE XK-36 AC 250V,16A VDE VDE (Alternative) Interchangeable Interchangeable AC 250V,16A VDE VDE (Alternative) (Alternative) (Alternative) (Alternative) Shenzhen Xiekang Electric Co., I-Sheng Electric Wire & Cable Co., Shanghai Yusheng Enterprise Development Co., Longkou Jin Sheng Electronics roducts Co., XK-01 AC 250V, 2.5A VDE EN S-021A AC 250V, 2.5A VDE EN YS-3 AC 250V, 2.5A VDE EN LFD-215 AC 250V, 2.5A VDE EN UL UL VDE VDE VDE VDE

42 Component (Alternative) (Alternative) Manufacturer/ trademark Zhejiang Yuehua Telecommunicat ion Co., Taiwan Line Tek Electronic Co., age 40 of 51 Report No.: Type/model Value / rating Standard Approval/ Reference Y205 AC 250V, 2.5A VDE EN L-21 AC 250V, 2.5A VDE EN (Alternative) Interchangeable Interchangeable AC 250V, 2.5A VDE EN (Alternative) (Alternative) (Alternative) (Alternative) (Alternative) ower Cord (Alternative) (Alternative) (Alternative) (Alternative) (Alternative) AC connector Shenzhen Xiekang Electric Co., Shanghai Yusheng Enterprise Development Co., Taiwan Line Tek Electronic Co., Zhejiang Yuehua Telecommunicat ion Co., VDE VDE VDE or TUV XK-28 AC 250V, 13A BS Intertek ASTA 972 YS-55 AC 250V, 13A BS BSI KM68299 L-61L AC 250V, 13A BS BSI KM55112 Y317 AC 250V, 13A BS BSI KM Interchangeable Interchangeable AC 250V, 13A or AC 250V 5A Shanghai Yusheng Enterprise Development Co., Zhejiang Yuehua Telecommunicat ion Co., I-Sheng Electric Wire & Cable Co., Mainland Electric Wire & Cable Co., Shenzhen Xiekang Electric Co., H03VVH2-F H05VVH2-F Interchangeable H03VVH2-F H05VVH2-F I-Sheng Electric Wire & Cable Co., BS x0.75mm 2 IEC VDE H03VVH2-F 2x0.75mm 2 IEC VDE H03VVH2-F 2x0.75mm² VDE IEC H03VVH2-F 2x0.75mm 2 IEC VDE H03VVH2-F 2x0.75mm 2 IEC VDE IS-037 2x0.75mm 2 AC 250V, 2.5A, standard sheet C7 IEC or VDE BSI, Intertek or TUV VDE VDE VDE VDE VDE VDE or equivalent IEC/EN VDE

43 Component (Alternative) (Alternative) (Alternative) (Alternative) (Alternative) (Alternative) Manufacturer/ trademark I-Sheng Electric Wire & Cable Co., Taiwan Linetek Electronic Co., Shanghai Yusheng Enterprise Development Co., Ltd Weihai Honglin Electronic Co., Ltd Weihai Honglin Electronic Co., Ltd Shenzhen Xiekang Electric Co., Rear Enclosure Qingdao Guoen Science & Technology Co., (Alternative) (Alternative) Huizhou Wote Advanced Materials Co., Orinko (Hefei) Advanced lastic Co Ltd Front enclosure Asia Int i Enterprise (Hongkong) Co., Ltd Alternative Alternative Alternative Stand Alternative SDI CHEMICAL CO LTD Huizhou Wote Advanced Materials Co., Ltd Orinko (Hefei) Advanced lastic Co., Ltd SAMYANG Corporation LG Chem (Tianjin) Engineering lastics Co., Ltd age 41 of 51 Report No.: Type/model Value / rating Standard Approval/ Reference IS-033 LS-7 YS-65 HL-028 HL-028S XK-05 S3001Z- 600A(b) 51(x)FR HIS-2230 AC 250V, 2.5A, standard sheet C7 AC 250V, 2.5A, standard sheet C7 AC 250V, 2.5A, standard sheet C7 AC 250V, 2.5A, standard sheet C7 AC 250V, 2.5A, standard sheet C7 AC 250V, 2.5A, standard sheet C7 V-0, Min. 2.5mm thick. V-0, Min. 2.5mm thick. V-0, Min. 2.5mm thick. IEC/EN VDE IEC/EN VDE IEC/EN VDE IEC/EN VDE IEC/EN VDE IEC/EN VDE UL 94 UL 94 UL 94 UL E UL E UL E AIEA2200FR(#) V-0 UL 94 UL E LS-1159(R) V-1 min. UL 94 UL E V-0 UL 94 UL E C/ABS-551X V-0 UL 94 UL E NHF V-0 UL 94 UL E LUOY GN- 5001RF(T) V-0 UL 94 UL E302314

44 Component Alternative Manufacturer/ trademark SDI CHEMICAL CO LTD age 42 of 51 Report No.: Type/model Value / rating Standard Approval/ Reference NH-1017(p) V-0 UL 94 UL E Notes: 1) An asterisk indicates a mark which assures the agreed level of surveillance 2) The supply cord is applicable with the main plug only which was evaluated during certification of the main plug. 3) All sources of enclosure material were considered for all test items in clause 12. 4) For interchangeable sources, the validity of the certificates shall be checked during national approval. Remarks Supplementary test results for subclause 9.1.1: Measured between: Uoc (V) U 1 (V) Limit U 1 U 2 (V) Limit U 2 L/N and Signal connectors L/N and LCD panel/ enclosure V V V V Notes: Input voltage 264V, 50Hz Supplementary test results for subclause 11.1: Measured between: Fault conditions Uoc (V) U 1 (V) Limit U 1 U 2 (V) Limit U 2 L/N and Signal connectors L/N and LCD panel/ enclosure Fuse broken Fuse broken V V V V L/N and Signal connectors L/N and LCD panel/ enclosure Notes: Input voltage 264V, 50Hz X901 output L1+ to GND, s- c X901 output L1+ to GND, s- c V V V V and Safety isolation transformer Construction details: See below Transformer part name: T831 Manufacturer: (see appended table 14) Type: (see appended table 14) Recurring peak voltage Required clearance for reinforced insulation (from table 8 and 9) Effective voltage rms Required creepage distance for reinforced insulation (from table 11) 516Vpk 4.4mm (BI=SI=2.2mm) 314Vrms 6.8mm (BI=SI=3.4mm) Measured min. creepage distance Location inside (mm) outside (mm)

45 age 43 of 51 Report No.: rimary to Secondary (RI) rimary to core (BI) Secondary to core (SI) Measured min. clearances Location inside (mm) outside (mm) rimary to Secondary (RI) rimary to core (BI) Secondary to core (SI) Remark: 1. Core of T831 is considered as Inter-Medium part. Three layers insulation tapes wrapped outside the core. 2. Concentric windings on phenolic bobbin, there are three layers of insulation tapes between primary windings and secondary windings. 3. Min 7.5 mm width margin tape used inside on primary side and Min 5.5 mm width margin tape used on secondary side. Insulation tubing used at the end of secondary winding. The bobbin between the pins to the core is min. 0.8mm. 4. The primary and secondary pins molded to bobbin and directly soldered to CB. Construction:

46 age 44 of 51 Report No.: WINDING CONSTRUCTION and Dismantling

47 age 45 of 51 Report No.: Notes: The unit of the dimension is mm. All transformers have the same construction. They are identical except for manufacturer and model name. in numbers Hazards winding 1-2-3, 5-6 Non-hazards winding 7-11, 8-9/10 Bobbin Material Thickness Electric strength test Result 1. Sumitomo Chemical Co., Type No. M9820, henolic, 150 C; 2. Chang Chun lastic Co., Type No. T375J, henolic Molding Compound, 150 C. Min. 0.8 mm With 3000 Vac after humidity treatment ass Transformer part name: T901 Manufacturer: (see appended table 14) Type: (see appended table 14) Recurring peak voltage Required clearance for reinforced insulation (from table 8 and 9) Effective voltage rms Required creepage distance for reinforced insulation (from table 11) 556Vpk 4.4mm (BI=SI=2.2mm) 261Vrms 5.4mm (BI=SI=2.7mm) Measured min. creepage distance Location inside (mm) outside (mm) rimary to Secondary (RI) rimary to core (BI) Secondary to core (SI) Measured min. clearances

48 age 46 of 51 Report No.: Location inside (mm) outside (mm) rimary to Secondary (RI) rimary to corer (BI) Secondary to core (SI) Remark: 1. Core is counted as Inter-Medium part. Different concentric winding on bobbin; 2. One side winding is primary windings. The other side winding is secondary; 3. The core outside body is wrapped with 3 layers of insulation tape. Construction:

49 age 47 of 51 Report No.:

50 age 48 of 51 Report No.: Notes: The unit of the dimension is mm. All transformers have the same construction. They are identical except for manufacturer and model name. in numbers Hazards winding 3-6 Non-hazards winding Bobbin Material Thickness Electric strength test Result 1. Sumitomo Chemical Co., Type No. M9820, henolic, 150 C; 2. Chang Chun lastic Co., Type No. T375J, henolic Molding Compound, 150 C. Min. 0.6 mm With 3000 Vac after humidity treatment ass Transformer part name: T902 Manufacturer: (see appended table 14) Type: (see appended table 14) Recurring peak voltage Required clearance for reinforced insulation (from table 8 and 9) Effective voltage rms Required creepage distance for reinforced insulation (from table 11) 420Vpk 4.0mm (BI=SI=2.0mm) 250Vrms 5.0mm (BI=SI=2.5mm) Measured min. creepage distance Location inside (mm) outside (mm) rimary to Secondary (RI) / see note rimary to core / see note 2 / see note 2 Secondary to core (RI) / see note Measured min. clearances Location inside (mm) outside (mm) rimary to Secondary (RI) / see note rimary to core / see note 2 / see note 2 Secondary to core (RI) / see note Construction: 1. Concentric windings on phenolic bobbin. 2. The core is considered as primary winding. 3. Triple Insulation Winding is used for secondary winding.

51 age 49 of 51 Report No.:

52 age 50 of 51 Report No.: WINDING CONSTRUCTION Notes: The unit of the dimension is mm. All transformers have the same construction. They are identical except for manufacturer and model name. in numbers Hazards winding 6-7, 9-10 Non-hazards winding 5-1

53 age 51 of 51 Report No.: Bobbin Material Thickness Electric strength test Result Chang Chun lastic Co., Type No. T375J, henolic Molding Compound, 150 C Min. 0.6 mm With 3000 Vac after humidity treatment ass --The End of this Test Report--

54 ATTACHMENT 1 age 1 of 16 Report No.: IEC60065K - ATTACHMENT Clause Requirement + Test Result - Remark Verdict ATTACHMENT TO TEST REORT IEC EUROEAN GROU DIFFERENCES AND NATIONAL DIFFERENCES Audio, video and similar electronic apparatus Safety requirements Differences according to... : EN 60065: A1: A11: A2: A12:2011 Attachment Form No.... : Attachment Originator... : EU_GD_IEC60065K_II Intertek Semko AB Master Attachment... : Date ( ) Copyright 2011 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE), Geneva, Switzerland. All rights reserved. IEC 60065, GROU DIFFERENCES (CENELEC common modifications (EN)) Clause Requirement + Test Result - Remark Verdict Contents Definition 2.2.Z1 (A11:2008) 2.2 (A12:2011) Add the following annexes: Annex ZA (normative) Other international publications quoted in this standard with the references of the relevant European publications (See the CB Bulletin) Annex ZB (nominative) Special national conditions Annex ZC (informative) A-deviations Add after the definition the following new definition: ORTABLE SOUND SYSTEM small battery powered audio equipment: whose prime purpose is to listen to recorded or broadcasted sound; and that uses headphones or earphones that can be worn in or on or around the ears; and that allows the user to walk around NOTE Examples are mini-disc or CD players, M3 audio players or similar equipment. In EN 60065:2002/A11:2008 Delete the definition 2.2.Z1

55 ATTACHMENT 1 age 2 of 16 Report No.: IEC60065K - ATTACHMENT Clause Requirement + Test Result - Remark Verdict 3.1 Add the following indent at the end of the list 3.1 (A12:2011) 3.Z1 (A2:2010) - Exposure to excessive sound pressures from headphones or earphones NOTE A new method of measurement is described in EN , Sound system equipment: Headphones and earphones associated with portable audio equipment Maximum sound pressure level measurement methodology and limit considerations art 1: General method for one package equipment, and in EN , Sound system equipment: Headphones and earphones associated with portable audio equipment Maximum sound pressure level measurement methodology and limit considerations art 2: Guidelines to associate sets with headphones coming from different manufacturers. In EN 60065:2002 Delete the addition of indent regarding sound pressure excessive After 3.2 add a new clause 3.Z1: To protect against excessive current, short-circuits and earth faults in MAINS, protective devices shall be included either as integral parts of the equipment or as parts of the building installation, subject to the following, a), b) and c): a) except as detailed in b) and c), protective devices necessary to comply with the requirements of 11 shall be included as parts of the equipment; b) for components in series or parallel with the mains input to the equipment such as the supply cord, appliance coupler, r.f.i. filter and switch, shortcircuit and earth fault protection may be provided by protective devices in the building installation; c) it is permitted for equipment supplied via an industrial mains plug or for ERMANENTLY CONNECTED AARATUS, to rely on dedicated over current and short-circuit protection in the building installation, provided that the means of protection, e.g. fuses or circuit breakers, is fully specified in the installation instructions. If reliance is placed on protection in the building installation, the installation instructions shall so state, except that for not via an industrial mains plug or for ERMANENTLY CONNECTED AARATUS the building installation shall be regarded as providing protection in accordance with the rating of the wall socket outlet Replace the text of the note by: NOTE For ROUTINE TEST reference is made to EN Deleted. a) & b) Considered.

56 ATTACHMENT 1 age 3 of 16 Report No.: IEC60065K - ATTACHMENT Clause Requirement + Test Result - Remark Verdict za) (A11:2008) Modify indent za) as follows: za) For a ORTABLE SOUND SYSTEM, a warning that excessive sound pressure from earphones and headphones can cause hearing loss. Not a ORTABLE SOUND SYSTEM (A12:2011) In EN 60065:2002/A1:2006 and EN 60065;2002/A11:2008 Delete the modification in indent za) Not a personal music player. Add the following clause and annex to the existing standard and amendments Zx rotection against excessive sound pressure from personal music players

57 ATTACHMENT 1 age 4 of 16 Report No.: IEC60065K - ATTACHMENT Clause Requirement + Test Result - Remark Verdict Zx.1 General This sub-clause specifies requirements for protection against excessive sound pressure from personal music players that are closely coupled to the ear. It also specifies requirements for earphones and headphones intended for use with personal music players. A personal music player is a portable equipment for personal use, that: recorded or broadcast sound or video; and can be worn in or on or around the ears; and NOTE 1 Examples are hand-held or body-worn portable CD players, M3 audio players, mobile phones with M3 type features, DA s or similar equipment. A personal music player and earphones or headphones intended to be used with personal music players shall comply with the requirements of this sub-clause. The requirements in this sub-clause are valid for music or video mode only. The requirements do not apply: an external amplifier; or used. NOTE 2 An external amplifier is an amplifier which is not part of the personal music player or the listening device, but which is intended to play the music as a standalone music player. The requirements do not apply to: equipment; NOTE 3 rofessional equipment is equipment sold through special sales channels. All products sold through normal electronics stores are considered not to be professional equipment. music players without any kind of digital processing of the sound signal) that are brought to the market before the end of NOTE 4 This exemption has been allowed because this technology is falling out of use and it is expected that within a few years it will no longer exist. This exemption will not be extended to other technologies. For equipment which is clearly designed or intended for use by young children, the limits of EN 71-1 apply.

58 ATTACHMENT 1 age 5 of 16 Report No.: IEC60065K - ATTACHMENT Clause Requirement + Test Result - Remark Verdict Cont. Zx.2 Equipment requirements No safety provision is required for equipment that complies with the following: music player with its listening device), where the acoustic output LAeq,T is 85 dba measured while playing the fixed programme simulation noise as described in EN ; and ided with an analogue electrical output socket for a listening device, where the electrical output is 27 mv measured as described in EN , while playing the fixed programme simulation noise as described in EN NOTE 1 Wherever the term acoustic output is used in this clause, the 30 s A-weighted equivalent sound pressure level LAeq,T is meant. See also Zx.5 and Annex Zx. All other equipment shall: a) protect the user from unintentional acoustic outputs exceeding those mentioned above; and b) have a standard acoustic output level not exceeding those mentioned above, and automatically return to an output level not exceeding those mentioned above when the power is switched off; and c) provide a means to actively inform the user of the ncreased sound pressure when the equipment is operated with an acoustic output exceeding those mentioned above. Any means used shall be acknowledged by the user before activating a mode of operation which allows for an acoustic output exceeding those mentioned above. The acknowledgement does not need to be repeated more than once every 20 h of cumulative listening time; and NOTE 2 Examples of means include visual or audible signals. Action from the user is always required. NOTE 3 The 20 h listening time is the accumulative listening time, independent how often and how long the personal music player has been switched off. d) have a warning as specified in Zx.3; and e) not exceed the following: 1) equipment provided as a package (player with Its listening device), the acoustic output shall be 100 dba measured while playing the fixed programme simulation noise described in EN ; and 2) a personal music player provided with an analogue electrical output socket for a listening device, the electrical output shall be 150 mv measured as described in EN , while playing the fixed programme simulation noise described in EN

59 ATTACHMENT 1 age 6 of 16 Report No.: IEC60065K - ATTACHMENT Clause Requirement + Test Result - Remark Verdict Cont. For music where the average sound pressure (long term LAeq,T) measured over the duration of the song is lower than the average produced by the programme simulation noise, the warning does not need to be given as long as the average sound pressure of the song is below the basic limit of 85 dba. In this case T becomes the duration of the song. NOTE 4 Classical music typically has an average sound pressure (long term LAeq,T) which is much lower than the average programme simulation noise. Therefore, if the player is capable to analyse the song and compare it with the programme simulation noise, the warning does not need to be given as long as the average sound pressure of the song is below the basic limit of 85 dba. For example, if the player is set with the programme simulation noise to 85 dba, but the average music level of the song is only 65 dba, there is no need to give a warning or ask an acknowledgement as long as the average sound level of the song is not above the basic limit of 85 dba. Zx.3 Warning The warning shall be placed on the equipment, or on the packaging, or in the instruction manual and shall consist of the following: of 5 mm; and To prevent possible hearing damage, do not listen at high volume levels for long periods. Figure 1 Warning label (IEC ) Alternatively, the entire warning may be given through the equipment display during use, when the user is asked to acknowledge activation of the higher level.

60 ATTACHMENT 1 age 7 of 16 Report No.: IEC60065K - ATTACHMENT Clause Requirement + Test Result - Remark Verdict Cont. Zx.4 Requirements for listening devices (headphones and earphones) Zx.4.1 Wired listening devices with analogue input With 94 dba sound pressure output LAeq,T, the input voltage of the fixed programme simulation noise described in EN shall be 75 mv. This requirement is applicable in any mode where the headphones can operate (active or passive), including any available setting (for example built-in volume level control). NOTE The values of 94 dba 75 mv correspond with 85dBA 27 mv and 100 dba 150 mv. Zx.4.2 Wired listening devices with digital input Not a listening device.. With any playing device playing the fixed programme simulation noise described in EN (and respecting the digital interface standards, where a digital interface standard exists that specifies the equivalent acoustic level), the acoustic output LAeq,T of the listening device shall be 100 dba. This requirement is applicable in any mode where the headphones can operate, including any available setting (for example built-in volume level control, additional sound feature like equalization, etc.). NOTE An example of a wired listening device with digital input is a USB headphone. Zx.4.3 Wireless listening devices In wireless mode: the fixed programme simulation noise described in EN ; and sion standards, where an air interface standard exists that specifies the equivalent acoustic level; and device (for example built-in volume level control, additional sound feature like equalization, etc.) set to the combination of positions that maximize the measured acoustic output for the abovementioned programme simulation noise, the acoustic output LAeq,T of the listening device shall be 100 dba. NOTE An example of a wireless listening device is a Bluetooth headphone.

61 ATTACHMENT 1 age 8 of 16 Report No.: IEC60065K - ATTACHMENT Clause Requirement + Test Result - Remark Verdict Zx.5 Measurement methods Measurements shall be made in accordance with EN or EN as applicable. Unless stated otherwise, the time interval T shall be 30 s. NOTE Test method for wireless equipment provided without listening device should be defined.

62 ATTACHMENT 1 age 9 of 16 Report No.: IEC60065K - ATTACHMENT Clause Requirement + Test Result - Remark Verdict 6.1 Replace the entire subclause in EN 60065:2002 and EN 60065:2002/A1:2006 by: No ionizing radiation source. (A11:2008) Ionizing radiation Apparatus including a potential source of ionizing radiation shall be so constructed that personal protection against ionizing radiation is provided under normal operating conditions and under fault conditions. Compliance is checked by measurement under the following conditions: In addition to the normal operating conditions, all controls adjustable from the outside BY HAND, by any object such as a tool or a coin, and those internal adjustments or pre-sets which are not locked in a reliable manner, are adjusted so as to give maximum radiation whilst maintaining an intelligible picture for 1 h, at the end of which the measurement is made. NOTE 1 Soldered joints and paint lockings are examples of adequate locking. The dose-rate is determined by means of a radiation monitor with an effective area of 10 cm², at any point 10 cm from the outer surface of the apparatus. Moreover, the measurement shall be made under fault conditions causing an increase of the highvoltage, provided an intelligible picture is maintained for 1 h, at the end of which the measurement is made. The dose-rate shall not exceed 1μSv/h (0,1 mr/h) taking account of the background level. NOTE 2 These values appear in Directive 96/29/Euratom of 13th May A picture is considered to be intelligible if the following conditions are met: - a scanning amplitude of at least 70 % of the usable screen width; - a minimum luminance of 50 cd/m² with locked blank raster provided by a test generator; - a horizontal resolution corresponding to at least 1,5 MHz in the centre, with a similar vertical degradation; - not more than one flashover per 5 min.

63 ATTACHMENT 1 age 10 of 16 Report No.: IEC60065K - ATTACHMENT Clause Requirement + Test Result - Remark Verdict Z1 (A11:2008) Add the following new clause after Clause 20: Z1 Resistance to candle flame ignition A television set shall be so designed that the likelihood of ignition and the spread of fire caused by a candle flame is reduced. NOTE 1 An apparatus with a viewing screen is not regarded to be a television set if it is declared not to be so by the manufacturer. This requirement does not apply to the display screen of rear projection TV s. NOTE 2 This exemption has been allowed because this technology is falling out of use and it is expected that within a few years it will no longer exist. This exemption will not be extended to other technologies. NOTE 3 The frame around the screen is not exempted from the requirements. Wood and WOOD-BASED MATERIAL with a thickness of at least 6 mm is considered to fulfil the V-1 requirement when applying CLC/TS Compliance is checked according to CLC/TS NOTE 4 The term vertical, as used in the first dash of clause 5.2 of CLC/TS 62441, does not mean a perfectly vertical position. It should be interpreted as any surface that can be touched by the flame of a candle of 150 mm height and 20mm diameter while the candle is still touching the supporting surface. A typical candle used in the home is assumed to be 20 mm diameter. NOTE 5 It is expected that CLC/TS will in the future be replaced by a standard, at which time that standard will become applicable, subject to a vote by National Committees at the time. V-1 min. plastic material or metal material used for the enclosure. General Delete note Delete note 4 and note Delete notes 1 and Delete note Delete note Delete the note. 20 Delete note 2. Annex B Replace note 1 by: In the CENELEC countries listed in IEC 62151, special national conditions apply. Annex G Delete the note. Annex J.2 Annex N Delete the notes of Table J.1. Add after the introduction: For ROUTINE TEST reference is made to EN (Replaced by EN 50514)

64 ATTACHMENT 1 age 11 of 16 Report No.: IEC60065K - ATTACHMENT Clause Requirement + Test Result - Remark Verdict General (A2:2010) In IEC 60065:2001/A2 Delete all the country notes according to the following list: 5.3 Note Note 20 Note For special national conditions, see Annex ZB. Bibliography Additional EN standards. ZA Normative references to international publications with their corresponding European publications --- ZB ANNEX ZB TO EN 60065, SECIAL NATIONAL CONDITIONS (EN) DK: The following is added: Certain types of CLASS I apparatus, see , may be provided with a plug not establishing earthing continuity when inserted in Danish socketoutlets Justification: Heavy Current Regulations, Section 107. Refer to clause Not class I apparatus. 3.Z1 (A2:2010) Denmark Add to the end of the subclause rotection device in the equipment. Due to many existing installations where the socket-outlets can be protected with fuses with higher rating than the rating of the socket-outlets the protection for pluggable equipment type A shall be an integral part of the equipment. Justification: In Denmark an existing 13 A socket outlet can be protected by a 20 A fuse.

65 ATTACHMENT 1 age 12 of 16 Report No.: IEC60065K - ATTACHMENT Clause Requirement + Test Result - Remark Verdict 5.3 Finland, Norway and Sweden Not class I apparatus. (A2:2010) To the end of the subclause the following is added: CLASS I apparatus which is intended for connection to the building installation wiring via a plug or an appliance coupler, or both and in addition is intended for connection to other apparatus or a network shall, if safety relies on connection to protective earth or if surge suppressors are connected between the network TERMINALS and ACCESSIBLE parts, have a marking stating that the apparatus must be connected to an earthed MAINS socket-outlet. The marking text in the applicable countries shall be as follows: In Finland: "Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan" In Norway: Apparatet må tilkoples jordet stikkontakt In Sweden: Apparaten skall anslutas till jordat uttag 5.4 Finland, Norway and Sweden See above (A11:2008) To the end of 5.4 the following is added: CLASS I apparatus which is intended for connection to the building installation wiring via a plug or an appliance coupler, or both and in addition is intended for connection to other apparatus or a network shall, if safety relies on connection to protective earth or if surge suppressors are connected between the network TERMINALS and ACCESSIBLE parts, have a marking stating that the apparatus must be connected to an MAINS socket-outlet with protective earth. The marking text in the applicable countries shall be as follows: In Finland: Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan In Norway: Apparatet må tilkoples jordet stikkontakt In Sweden: "Apparaten skall anslutas till jordat uttag"

66 ATTACHMENT 1 age 13 of 16 Report No.: IEC60065K - ATTACHMENT Clause Requirement + Test Result - Remark Verdict (A11:2008) Norway and Sweden To the end of (after the compliance statement) the following is added: The screen of the cable distribution system is normally not earthed at the entrance of the building and there is normally no equipotential bonding system within the building. Therefore the protective earthing of the building installation need to be isolated from the screen of a cable distribution system. The relevant information shall be provided when the apparatus was sold in these countries. It is however accepted to provide the insulation external to the equipment by an adapter or an interconnection cable with galvanic isolator, which may be provided by e.g. a retailer. The user manual shall then have the following or similar information in Norwegian and Swedish language respectively, depending on in what country the equipment is intended to be used in: Equipment connected to the protective earthing of the building installation through the mains connection or through other equipment with a connection to protective earthing and to a cable distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection to a cable distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator, see EN ) NOTE In Norway, due to regulation for installations of cable distribution systems, and in Sweden, a galvanic isolator shall provide electrical insulation below 5 MHz. The insulation shall withstand a dielectric strength of 1,5 kv r.m.s., 50 Hz or 60 Hz, for 1 min. Translation to Norwegian (the Swedish text will also be accepted in Norway): Utstyr som er koplet til beskyttelsesjord via nettplugg og/eller via annet jordtilkoplet utstyr og er tilkoplet et kabel-tv nett, kan forårsake brannfare. For å unngå dette skal det ved tilkopling av utstyret til kabel-tv nettet installeres en galvanisk isolator mellom utstyret og kabel-tv nettet. Translation to Swedish: Utrustning som är kopplad till skyddsjord via jordat vägguttag och/eller via annan utrustning och samtidigt är kopplad till kabel-tv nät kan i vissa fall medföra risk för brand. Főr att undvika detta skall vid anslutning av utrustningen till kabel-tv nät galvanisk isolator finnas mellan utrustningen och kabel-tv nätet.

67 ATTACHMENT 1 age 14 of 16 Report No.: IEC60065K - ATTACHMENT Clause Requirement + Test Result - Remark Verdict NO: To the second paragraph the following is added: In Norway, due to the IT power distribution system used, the a.c. MAINS supply voltage is considered to be equal to the line-to-line voltage, and will remain 230 V in case of a single earth fault. Justification: Based on a use in Norway of an IT power distribution system where the neutral is not provided. The input voltage range of this apparatus covered 230V (A11:2008) Denmark The text of the Danish SNC in EN 60065:2002 has been modified as follows: To the first paragraph the following is added: In Denmark, supply cords of single-phase appliances having a rated current not exceeding 13 A shall be provided with a plug according to the Heavy Current Regulations Section D1. Appliances of CLASS I provided with socket-outlets with earth contact or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules shall be provided with a plug in accordance with the Heavy Current Regulations, Section D1 standard sheet DK 2-1a. To the second paragraph the following is added: Socket outlets intended for providing power to CLASS II apparatus with a rated current of 2,5 A shall be in accordance with the Heavy Current Regulation, Section D1 standard sheet DKA 1-4a. Other current ratings socket outlets shall be in compliance with the Heavy Current Regulation, Section D1 standard sheet DKA 1-3a or DKA 1-3b. To the third paragraph the following is added: Mains socket-outlets with earthing contact shall be in compliance with the Heavy Current Regulation, Section D1 standard sheet DK 1-3a, DK 1-5a or DK 1-7a. Justification: Heavy Current Regulations, Section D1 Relevant plug shall be provided when the apparatus was sold in these countries IE: Apparatus which is fitted with a flexible cable or cord shall be provided with a 13 A plug in accordance with Statutory Instrument 525:97, 13 A lugs and Conversion Adapters for Domestic Use Regulations:1997. Justification: SI 525: 1997 Relevant plug shall be provided when the apparatus was sold in this country.

68 ATTACHMENT 1 age 15 of 16 Report No.: IEC60065K - ATTACHMENT Clause Requirement + Test Result - Remark Verdict NO: Mains socket-outlets mounted on CLASS II apparatus shall comply with the specifications given in CEE ubl. 7 as far as a applicable, with the following amendments: 8 Dimensions a 2.5 A 250 V two-pole socket-outlets for electronic apparatus shall comply with the enclosed Standard Sheet I. No such socket-outlet used. 24 Mechanical strength A 2,5 A 250 V socket-outlets for CLASS II electronic apparatus are tested as specified in of EN Also the protecting rim shall be tested Justification: Act of 24 May 1929 relating to supervision of electrical installation (TEA 1929/FEL 1998) UK: Apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to BS 1363 by means of that flexible cable or cord and plug shall be fitted with a standard plug in accordance with Statutory Instrument 1768: 1994: The lugs and Sockets etc. (Safety) Regulations 1994, unless exempted by those Regulations. NOTE Standard plug is defined in SI 1768:1994 and essentially means an approved plug conforming to BS 1363 or an approved conversion plug. Justification: SI 1768: 1994 Approved plug according to BS provided.

69 ATTACHMENT 1 age 16 of 16 Report No.: IEC60065K - ATTACHMENT Clause Requirement + Test Result - Remark Verdict J.2 NO: After Table J.1 the following is added: In Norway, due to the IT power distribution system used, the a.c. MAINS supply voltage is considered to be equal to the line-to-line voltage, and will remain 230 V in case of a single earth fault. Justification: Based on a use in Norway of an IT power distribution system where the neutral is not provided. Alternative method not used. ZC ANNEX ZC TO EN 60065, A-DEVIATIONS (EN) 5.1 IT: Additional markings on the outside of the TV receiver in Italian language IT:User instructions in Italian language including a conformity declaration IT: Certification number on the back cover 6.1 DE: The following requirement applies: For the operation of any cathode ray tube intended for the display of visual images operating at an acceleration voltage exceeding 40 kv, authorization is required, or application of type approval (Bauartzulassung) and marking. Justification: German ministerial decree against ionizing radiation (Röntgenverordnung), in force since , implementing the European Directive 96/29/EURATOM. NOTE Contact address: hysikalisch-technische Bundesanstalt, Bundesallee 100, D Braunschweig, Tel.: Int , Internet: 14 SE: Switches containing mercury such as thermostats, relays and level controllers are not allowed. Justification: Ordinance (1990:944) on rohibition in Connection with handling. Importation and exportation of Chemical roducts (Certain Cases) The relevant marking shall be provided when the apparatus was sold in these countries. The relevant information shall be provided when the apparatus was sold in these countries. It shall be evaluated when submitted for national approval. No such devices. Switch shall meet this requirement when the apparatus was sold in this country.

70 ATTACHMENT 2 Report No.: Type Designation: hoto Documentation HE50K3300UWTS, H50M3300, H50M3306, H50M3308, H50MEC3350 H50MEC3355 ic001 Front appearance ic002 Back appearance Rev. 1 age 1 of 10

71 ATTACHMENT 2 Report No.: Type Designation: hoto Documentation HE50K3300UWTS, H50M3300, H50M3306, H50M3308, H50MEC3350 H50MEC3355 ic003 Back appearance without stand ic004 Marking for signal connectors Rev. 1 age 2 of 10

72 ATTACHMENT 2 Report No.: Type Designation: hoto Documentation HE50K3300UWTS, H50M3300, H50M3306, H50M3308, H50MEC3350 H50MEC3355 ic005 Marking for signal connectors ic006 Internal view without back cover Insulation sheet Rev. 1 age 3 of 10

73 ATTACHMENT 2 Report No.: Type Designation: hoto Documentation HE50K3300UWTS, H50M3300, H50M3306, H50M3308, H50MEC3350 H50MEC3355 ic007 Main switch ic008 Back cover Rev. 1 age 4 of 10

74 ATTACHMENT 2 Report No.: Type Designation: hoto Documentation HE50K3300UWTS, H50M3300, H50M3306, H50M3308, H50MEC3350 H50MEC3355 ic009 ower supply board ic010 ower supply board Rev. 1 age 5 of 10

75 ATTACHMENT 2 Report No.: Type Designation: hoto Documentation HE50K3300UWTS, H50M3300, H50M3306, H50M3308, H50MEC3350 H50MEC3355 ic011 Insulation sheet under power supply board ic012 Mainboard Rev. 1 age 6 of 10

76 ATTACHMENT 2 Report No.: Type Designation: hoto Documentation HE50K3300UWTS, H50M3300, H50M3306, H50M3308, H50MEC3350 H50MEC3355 ic013 Mainboard ic014 Transformer T831 Rev. 1 age 7 of 10

77 ATTACHMENT 2 Report No.: Type Designation: hoto Documentation HE50K3300UWTS, H50M3300, H50M3306, H50M3308, H50MEC3350 H50MEC3355 ic015 Transformer T831 ic016 Transformer T901 Rev. 1 age 8 of 10

78 ATTACHMENT 2 Report No.: Type Designation: hoto Documentation HE50K3300UWTS, H50M3300, H50M3306, H50M3308, H50MEC3350 H50MEC3355 ic017 Transformer T901 ic018 Transformer T902 Rev. 1 age 9 of 10

79 ATTACHMENT 2 Report No.: Type Designation: hoto Documentation HE50K3300UWTS, H50M3300, H50M3306, H50M3308, H50MEC3350 H50MEC3355 ic019 Transformer T902 ic020 Stand Rev. 1 age 10 of 10