TEST REPORT IEC : 2005 (2nd Edition) and/or EN :2006 Information technology equipment Safety Part 1: General requirements

Size: px

Start display at page:

Download "TEST REPORT IEC : 2005 (2nd Edition) and/or EN :2006 Information technology equipment Safety Part 1: General requirements"

Rolf Atkinson
5 years ago
Views:

Test Report issued under the responsibility of: NCB TÜV SÜD PSB Pte Ltd 1 Science Park Drive, Singapore 118221 TEST REPORT IEC 60950-1: 2005 (2nd Edition) and/or EN 60950-1:2006 Information

1 Test Report issued under the responsibility of: NCB TÜV SÜD PSB Pte Ltd 1 Science Park Drive, Singapore TEST REPORT IEC : 2005 (2nd Edition) and/or EN :2006 Information technology equipment Safety Part 1: General requirements Report Reference No....: Date of issue... : Total number of pages CB/CCA Testing Laboratory... : Address... : Applicant s name... : Address... : Manufacturer s name... : Address... : Factory s name... : Address... : Test specification: Standard... : Test procedure... : Non-standard test method..: Test Report Form No.... : Test Report Form(s) Originator... : TÜV SÜD Asia Ltd. Taiwan Branch Beitou District, Taipei City, 11270, Taiwan. Delta Electronics, Inc. No. 3, Tung Yuan Rd., Chungli Ind. Zone, Taoyuan Hsien, Taiwan. Delta Electronics, Inc. No. 3, Tung Yuan Rd., Chungli Ind. Zone, Taoyuan Hsien, Taiwan. See page 5 for details. See page 5 for details. IEC :2005 (2nd Edition) and/or EN : A11:2009 CB / CCA IECEN60950_1C SGS Fimko Ltd Master TRF... : Dated Copyright 2007 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE), Geneva, Switzerland. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. If this Test Report Form is used by non-iecee members, the IECEE/IEC logo and the reference to the CB Scheme procedure shall be removed. This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02. If this Test Report Form is used by non-cca members, the CIG logo and the reference to the CCA Procedure shall be removed. This report is not valid as a CCA Test Report unless signed by an approved CCA Testing Laboratory and appended to a CCA Test Certificate issued by an NCB in accordance with CCA Page 1 of 14

2 Test item description... : DLP Projector Trade Mark... : Manufacturer... : Model/Type reference... : Ratings... : Testing procedure and testing location: CB/CCA Testing Laboratory: Testing location/ address... : Associated CB Laboratory: Testing location/ address... : Tested by (name + signature)...: Approved by (+ signature)...: Testing procedure: TMP Tested by (name + signature)...: Approved by (+ signature)...: Testing location/ address... : 1. Optoma 2. InFocus Same as applicant 1. EH106y, DAEXTyy, DAEHGyyy, DAEHNyyy, EH206y, EX78yy, EX77yy 2. SP86y0 ( y can be any character or blank) Vac, 50/60 Hz, 3.5 A or 4.2 A (when 300W lamp is used) TÜV SÜD Asia Ltd. Taiwan Branch Beitou District, Taipei City, 11270, Taiwan. Mr. Larry Lai Mr. Watson Yang Testing procedure: WMT Tested by (name + signature)...: Witnessed by (+ signature)...: Approved by (+ signature)...: Testing location/ address...: Testing procedure: SMT Tested by (name + signature)...: Approved by (+ signature)...: Supervised by (+ signature)...: Testing location/ address...: Testing procedure: RMT Tested by (name + signature)...: Approved by (+ signature)...: Supervised by (+ signature)...: Testing location/ address...: Page 2 of 14

3 Summary of testing: Tests performed (name of test and test clause): All test results were found satisfactory in accordance with IEC :2005(2 nd Edition) and / EN : A11:2009. Testing location: All tests as described in Test Case and Measurement Sections were performed at the laboratory described on page 2. Summary of compliance with National Differences: National Differences for Austria (AT), Canada (CA), Germany (DE), Denmark (DK), Finland (FI), France (FR), United Kingdom (GB), Italy (IT), Japan (JP), Korea (KR), The Netherlands (NL), Norway (NO), Poland (PL), Sweden (SE), Slovenia (SI), United States of America (US). Group Differences as listed in the CB Bulletin No. 112A (December 2006) are recorded at the end of this report. Copy of marking plate See attachment No. 2 of Test Report Ref. No.: and attachment No. 1 of Test Report Ref. No.: and attachment No. 1 of Test Report Ref. No.: Page 3 of 14

4 Test item particulars... : Equipment mobility... : [Χ] movable [] hand-held [] transportable [] stationary [] for building-in [] direct plug-in Connection to the mains... : Operating condition... : [Χ] pluggable equipment [Χ] type A [] type B [] permanent connection [Χ] detachable power supply cord [] non-detachable power supply cord [] not directly connected to the mains [Χ] continuous [] rated operating / resting time: Access location...: [Χ] operator accessible [] restricted access location Over voltage category (OVC)...: [] OVC I [Χ] OVC II [] OVC III [] OVC IV [] other: Mains supply tolerance (%) or absolute mains supply +10%, -10% values...: Tested for IT power systems... : [Χ] Yes [] No IT testing, phase-phase voltage (V)... : 230V (for Norway) Class of equipment...: [Χ] Class I [] Class II [] Class III [] Not classified Considered current rating (A)...: 16A or 20A for US Pollution degree (PD)... : [] PD 1 [Χ] PD 2 [] PD 3 IP protection class... : Ordinary Altitude during operation (m)... : Up to 2000 Altitude of test laboratory (m)... : Below 2000 Mass of equipment (kg)... : Approx. 3.3 Possible test case verdicts: - test case does not apply to the test object... : - test object does meet the requirement... : P (Pass) - test object does not meet the requirement... : F (Fail) Testing... : Date of receipt of test item... : Date(s) of performance of tests... : to Page 4 of 14

5 General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(See Enclosure #)" refers to additional information appended to the report. "(See appended table)" refers to a table appended to the report. Note: This TRF includes EN Group Differences together with National Differences and Special National Conditions, if any. All Differences are located in the Appendix to the main body of this TRF. Throughout this report a point is used as the decimal separator. Factory: Delta Video Display System (Wujiang) Limited ( ID No.: 45855) 1688, JiangXing E.Rd., WuJiang Economic, Development Zone, WuJiang City, JiangSu, People's Republic of China Attachments: Original Test Report No pages + 38 pages attachments Additional Test Report No pages + 1 page attachments Attachment No. 1 Marking Plate 1 page Attachment No. 2 Photo 1 page Report No. < > The construction of the DLP Projector models EX77y, EH106y, DAEXTyy and DAEHGyyy were modified as follows: 1. Add new models DAEHNyyy, EH206y, EX78yy, EX77yy and delete model EX77y. 2. Add input current ratings 4.2 A when 300W lamp is used. 3. Alternate component for Lamp, Ballast, Fuse and revise manufacturer of Enclosure see table for details. For the above described modification the following Clause/Testing was considered to be necessary: S/N Clause/Testing Remark/Comments Verdict 1. Clause 1.7 Marking and instructions P 2. Table List of critical components P 3. Table electrical data (in normal conditions) P 4. Table 4.5 Thermal requirements P 5. Table 5.2 Electric strength measurements P 6. Table 5.3 Fault condition tests P Page 5 of 14

6 General product information: The equipment is a DLP Projector of information technology equipment. In models EH106y, DAEXTyy, DAEHGyyy, DAEHNyyy, EH206y, EX78yy, EX77yy and SP86y0, where y can be any character or blank to denote different client ID. All models are identical except for model designation and trademark. The maximum ambient temperature specified by manufacturer is 40 o C. Unless otherwise indicated, all tests are performed on model EX77 to represent other similar models. Page 6 of 14

7 IEC/EN Clause Requirement + Test Result - Remark Verdict 1.7 Marking and instructions P Power rating See below. P Rated voltage(s) or voltage range(s) (V)... : Vac P Symbol for nature of supply, for d.c. only... : Mains from AC source. Rated frequency or rated frequency range (Hz)... : 50/60 Hz P Rated current (ma or A)... : Manufacturer s name or trade-mark or identification mark... : 3.5 A or 4.2 A (when 300W lamp is used) 1. Optoma 2. InFocus Model identification or type reference... : 1. EH106y, DAEXTyy, DAEHGyyy, DAEHNyyy, EH206y, EX78yy, EX77yy 2. SP86y0 ( y can be any character or blank) Symbol for Class II equipment only... : Class I equipment. Other markings and symbols... : Additional symbols or markings that do not give rise to misunderstand. P P P P Page 7 of 14

8 1.5.1 TABLE: List of critical components P Object/part No. Alternate Component Manufacturer/ trademark Lamp (Alternate) Philips UHP W 1.1 E21.7 Ballast (Alternate) Fuse (F101) (alternate) only for 300W lamp Fuse (F101) (alternate) only for 300W lamp Revised Component Type/model Technical data Standard (Edition / year) Ignition voltage 7.5 kv max., 300W Philips EUC 300e B/F11 I/P: Vdc, 1300m A, O/P:200~330 W Mark(s) of conformity 1 ) EN :2006 KEMA Littelfuse 215 T6.3AH, 250V EN/IEC , EN/IEC Bel 5HT T6.3AH, 250V EN/IEC , EN/IEC Enclosure Styron Celex 3600 HP 5V, 125 C, min. 2.5mm thick. Enclosure (back IO cover and keypad cover) Styron Celex 3600 HP 5V, 125 C, min. 2.5mm thick. 1 ) an asterisk indicates a mark which assures the agreed level of surveillance UL 94, UL 746C UL 94, UL 746C UL, VDE UL, VDE UL UL Page 8 of 14

9 1.6.2 TABLE: electrical data (in normal conditions) P U (Vac/Hz) I (A) Irated (A) P (W) Fuse # Ifuse (A) Condition/status With VGA input, audio out and 12V trigger (Test with Lamp: Philips type: UHP W 1.1 E21.7 and Ballast, Philips type: EUC 300e B/F11 ) 90/ F Maximum Normal load 90/ F Maximum Normal load 100/ F Maximum Normal load 100/ F Maximum Normal load 240/ F Maximum Normal load 240/ F Maximum Normal load 264/ F Maximum Normal load 264/ F Maximum Normal load Page 9 of 14

10 4.5 TABLE: Thermal requirements P Supply voltage (V)... : See below. Ambient T min ( C)... : Ditto. Ambient T max ( C)... : Maximum measured temperature T of part/at: T ( C) Allowed T max ( C) Test with Lamp: Philips type: UHP W 1.1 E21.7 and Ballast, Philips type: EUC 300e B/F11 Test condition Normal projection Ceiling projection -- 90V 264V 90V 264V 01. T301 coil T301 core ISO ISO CY C CX CY TVR PCB under NTC CR FL FL D Q L D F L AC inlet L20 (BALLAST) L19(ballast) Page 10 of 14

11 Maximum measured temperature T of part/at: Test condition T ( C) Allowed T max ( C) Normal projection Ceiling projection -- 90V 264V 90V 264V L3 (BALLAST) L6 (ballast) Lamp Housing Lamp Cover Label s Position Video s body Vent. Openings Ambient Page 11 of 14

12 Temperature T of winding: t 1 ( C) R 1 ( ) t 2 ( C) R 2 ( ) T ( C) Allowed T max ( C) Insulation class Supplementary information: The temperatures were measured by thermal couple (type K) method under worst case normal mode as described in at voltage described in The worst case normal mode is defined with max load of the equipment. With max. ambient temperature specified as 40 C, therefore, the maximum temperature rise is calculated as follows: Winding components: - class B Max temp=120 C-10 C= 110 C Components with: - Max. temp. of 70 C(lnlet) - Max. temp. of 85 C(X-cap,Y-cap and others capacitors) - Max. temp. of 100 C(Opto-coupler) - Max. temp. of 130 C (FL102, FL101, L102) - Max. temp. of 105 C(PCB and L101) - Max. temp. of 85 C(Ripple capacitor) - Max. temp. of 70 C(plastic enclosure) - Max. temp. of 200 C(Lamp holder) - when no class of insulation is given, min. insulation 105 C assumed. User accessible area: - material is plastic (95 C) Page 12 of 14

13 5.2 TABLE: Electric strength measurements P test voltage applied between: test voltage (V) breakdown Primary-PE AC 2527V No Primary-Secondary DC 4242V No Page 13 of 14

14 5.3 TABLE: Fault condition tests P Component No. Ambient temperature ( C)... : 25 o C or see below Power source for EUT: Manufacturer, model/type, output rating... : Fault Supply voltage (Vac) Test time Fuse # Fuse current (A) See Table for detail Observation Test with Lamp: Philips type: UHP W 1.1 E21.7 and Ballast, Philips type: EUC 300e B/F11 Vent. Openings Blocked 240 2H F No fire, No hazards. Max. temperature of T301 coil: 73.3 C; T301 core: 70.6 C; IC101: 64.4 C; IC102: 67.9 C; CY105: 67.7 C; ambient: 28.0 C. Fan1 Blocked 240 2H F No fire, No hazards. Max. temperature of T301 coil: 70.0 C; T301 core: 65.9 C; IC101: 50.5 C; IC102: 55.8 C; CY105: 57.7 C; ambient: 24.2 C. Fan 2 Stalled H F No fire, No hazard. The unit shutdown immediately. Fan 3 Stalled H F No fire, No hazard. The unit shutdown immediately. Fan 4 Stalled H F No fire, No hazard. The unit shutdown immediately. Color Wheel Stalled H F No fire, No hazard. The unit shutdown immediately. Q101 (D-G) SC 240 1S F101 0 Q101 (S-D) SC 240 1S F101 0 C105 SC 240 1S F101 0 CR101 (2-4) SC 240 1S F101 0 CR101 (3-4) SC 240 1S F101 0 IC101 (1-7) SC 240 1S F101 0 Fuse open instantly, no damaged, no hazards. Fuse open instantly, no damaged, no hazards. Fuse open instantly, no damaged, no hazards. Fuse open instantly, no damaged, no hazards. Fuse open instantly, no damaged, no hazards. Fuse open instantly. ZD101 damaged, no hazards. Note: For fuse opened conditions, same results came out for all sources of fuse. If fuse not open have repeat test three times. Page 14 of 14

Attachment No. 1 Page 1 of 1 Note. The marking label for model EX77yy is used as a representative label for other models. All labels are identical except for model designation.

15 Attachment No. 1 Page 1 of 1 Note. The marking label for model EX77yy is used as a representative label for other models. All labels are identical except for model designation. The above labels are draft of artwork for marking plate pending approval by National Certification Bodies and they shall not be affixed to products prior to such an approval

16 Attachment No. 2 Page 1 of 1 Type Designation: EH106y, DAEXTyy, DAEHGyyy, DAEHNyyy, EH206y, EX78yy, EX77yy, SP86y0 Report Number: Ballast: Philips, type: UHP W 1.1 E21.7 Lamp: Philips, type: EUC 300e B/F11

TEST REPORT IEC Information technology equipment Safety Part 1: General requirements

TEST REPORT IEC Information technology equipment Safety Part 1: General requirements Test Report issued under the responsibility of: TEST REPORT IEC 60950-1 Information technology equipment Safety Part 1: General requirements Report Number.... : 210282-CI3-2 CB DE1-56459 Date of issue...