Certificate of Compliance

Transcription

1 Certificate of Compliance Certificate: Master Contract: Project: Date Issued: Issued to: Bel Fuse Inc. 206 Van Vorst St Jersey City, New Jersey USA Attention: Editha S. Vergara The products listed below are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' for Canada and US or with adjacent indicator 'US' for US only or without either indicator for Canada only. Issued by: Juan-Carlos Olivera Juan-Carlos Olivera, MSc. PRODUCTS CLASS POWER SUPPLIES - Component Type (CSA nd Ed) CLASS POWER SUPPLIES - Component Type (UL nd Ed) - Certified to U.S. Stds For details related to rating, size, configuration, etc. reference should be made to the CSA Certification Record or the descriptive report. Component power supply (switching type), Model LKP 5000 series, Model LK 5000 series, Model LK 4000 series, Model LS 5000 series, and Model LS 4000 series. Ratings (next page): DQD 507 Rev Page 1

2 Certificate: Project: Master Contract: Date Issued: Type Rated Input Operating Input Rated Output LKP V ac V A Hz V A Hz Output 1 Output / A Hz 255 V ac 2.1 A Hz Max V dc, max. 5.8 A There are two outputs: If you put them in parallel, you can provide one output with max. output current (LKP 5660) If you put them both in series, you can provide one output with max. output voltage (LKP 5740) Alternatively, both models can have a basic plate instead of the heatsink. Max V dc, max. 5.8 A Max. Total Output Power/W 280 Type Rated Input Operating Input Rated Output LK V ac V dc LK V ac V dc LS V ac V dc LS V ac V dc Max. Total Output Power/W V A Hz V A Hz Output 1 Output / V dc, A Hz 2.3A Hz max. 20 A A A A 50/60 Hz 50/60 Hz 50/60 Hz V ac V dc V ac V dc V ac V dc V ac V dc A A A Hz Hz Hz V dc, max. 6 A V dc, max. 16 A V dc, max. 4.2 A Max V dc, max. 6 A Max V dc, max. 4.2 A There are two outputs in X5000: If you put them in series, you can provide one output with max. output voltage 56.5V. (LK 574x-7R) Model differences: The S version has a smaller heatsink version than the K version. Alternatively, both models can have a base plate for mounting to another heatsink in the end product instead of the heatsink. Refer to list of safety critical components. Nomenclature: ab cdee-fgg (e.g. LK ER) ab can be: Series Designation and input voltage range: LK Input voltage V ac or V dc; output power 150W LS Input voltage V ac or V dc; output power 100W LKP Input voltage V ac; output power 250 W. c can be: and means: 4 One output 5 Two outputs 100 DQD 507 Rev Page 2

3 Certificate: Project: Master Contract: Date Issued: or higher Customer specific models: - Some only with mechanical changes; e.g. other front plate, other LEDS, and so on. - Some with other output voltages; e.g. 13 V. - Some with smaller input voltage range, but up to 280 W output power. Not safety relevant. d can be: and means output voltage: 0 or 1 or V dc 3 12 V dc 4 or 5 15 V dc 6 24 V dc 7 or 8 Customer specific products with output voltages between 2 and V dc May be followed by Other specifications for single output models. ee can be: and for models with two outputs means (except customer specific models): V dc, 12 V dc V dc, 15 V dc V dc, 24 V dc Customer specific products may have different output rating Other specifications and additional features. f can be: and means ambient range: -5 Up to 51ºC -6 Up to 60ºC -7-25ºC to 71ºC -9-40ºC to 71ºC -0, -1, -2, -3 or -4 Customer specific models gg can be: and means auxiliary functions and options: E Inrush current limitation. Option E is available for all models; mandatory for all -9 model types. R Output voltage control input. Feature R excludes option P, and vice versa. P Potentiometer (output voltage adjustment) D Save data signal (D0 DD; to be specified). Option D excludes option V, and vice versa. V ACFAIL signal (V2, V3). Option V is available for LK/LS 4000 types with 5 V outputs. T Current sharing. B1 Cooling plate standard case. B2 Cooling plate for long case 220 mm. K H15S2 connector replaced by H15S4 (only models with 5V output) APPLICABLE REQUIREMENTS DQD 507 Rev Page 3

4 Certificate: Project: Master Contract: Date Issued: CAN/CSA-C22.2 No , +Am.1:2011 +Am.2:2014 Information Technology Equipment - Safety - Part 1: General Requirements UL Information Technology Equipment - Safety - Part 1: General Requirements CONDITIONS OF ACCEPTABILITY 1. This component has been judged on the basis of the required spacings in the Standard for Safety of Information Technology Equipment, CSA/UL , Second Edition, dated March 27, 2007, including Am 1:2001 and Am 2:2014Sub-clause 2.10, which would cover the component itself if submitted for Listing. 2. All secondary output circuits are SELV up to 48 V dc and are not hazardous energy levels. 3. The terminals and connectors are suitable for factory wiring only. 4. Magnetic devices TR1 constructed of R/C insulation system Designated Class F (155 C). The auxiliary transformer is a planar type constructed of an (UL Approved printed wiring board material V-2 or better) rated 130 C. Consideration for conducting the temperature on the transformer needs to be measured in the end product use. 5. The equipment has been evaluated for use in a Pollution Degree 2 environment. 6. The input voltage rating specified contains the maximum and minimum voltage tested, no additional tolerances were considered. 7. The temperature test was conducted by monitoring the exposed heat sink temperature as rated in the manufacturer's specifications. The S Series was maintained at 95 C and the K Series at 85 C. Consideration should be given to measure the hotspot so that the specified maximum temperature (95 C for the S- and 85 C for the K- Series) will not be exceeded. 8. Suitability of the enclosure bond to earth is to be evaluated in the end use application 9. The disconnect device shall be a suitable type provided in the end use application. DQD 507 Rev Page 4

5 Supplement to Certificate of Compliance Certificate: (170351) Master Contract: The products listed, including the latest revision described below, are eligible to be marked in accordance with the referenced Certificate. Project Date Description Product Certification History Component power supply (switching type), Model LKP 5000 series, Model LK 5000 series, Model LK 4000 series, Model LS 5000 series, and Model LS 4000 series. (C/US) (transferred from and upgraded to include Am1 and Am2). DQD 507 Rev Page 1

6 CERTIFICATE No. P Order No Page 1/2 Product Applicant Manufacturer Factory Ratings AC/DC and DC/DC Switching power supply Bel Fuse Inc. 206 Van Vorst St. Jersey City, NJ USA Bel Fuse Inc. 206 Van Vorst St. Jersey City, NJ USA Bel Power Solutions, s.r.o. Areal ZTS Dubnica nad Vahom Slovakia See next page(s) Input: A, Vac, 50/60Hz Trade mark Model / Type Ref. Principal characteristics LKP Series Cl.I. Output: One or two output: Vdc Max., 20A Max; output power: 280W Max. See next page(s) A sample of the product was tested and found to be in conformity with OFF EN :2006;A11;A1;A12;A2 Validity Additional information This certificate documents conformity with the standards shown, and also applies as license for use of Nemkos name and certification mark. The certificate and license is valid as long as the applicable conditions are complied with, and provided that any changes to the product are notified to Nemko for acceptance prior to implementation. New standards or amendments to the standards may imply that the product design must be updated and/or that re-testing and re-certification is necessary. See next page(s) The abovementioned certified equipment complies with current regulatory requirements regarding electrical safety in Norway and other EU/EEA member states, as far as this can be checked. Compliance with requirements regarding building-in, protection against electric shock and Electromagnetic Compatibility (EMC) must be checked when the equipment is built-in a completed product or forms a part of a complete system. Additional model(s) See next page(s) Date of issue Juan Z. Kleppenes Certification Department Nemko AS Gaustadalléen 30, P.O. Box 73 Blindern, 0314 Oslo, Norway TEL FAX info@nemko.com ENTERPRISE NUMBER NO nemko.com

7 CERTIFICATE No. P Order No Page 2/2 Product AC/DC and DC/DC Switching power supply Pos. No 1 Model / Type Ref. LK Series Trade mark (if different from page 1) Rating Principal characteristics Input: A or A, Vac, 50/60Hz / A or A, Vdc Cl.I. Output: One or two output; 28.25Vdc Max., 20A Max. Output power: 150W Max. Product AC/DC and DC/DC Switching power supply Pos. No 2 Model / Type Ref. LS Series Trade mark (if different from page 1) Rating Principal characteristics Input: A or A, Vac, 50/60Hz / A or A, Vdc Cl.I. Output: One or two output; 28.25Vdc Max., 20A Max. Output power: 100W Max. Date of issue Juan Z. Kleppenes Certification Department Nemko AS Gaustadalléen 30, P.O. Box 73 Blindern, 0314 Oslo, Norway TEL FAX info@nemko.com ENTERPRISE NUMBER NO nemko.com

8 Ref. Certif. No. NO87302 IEC SYSTEM FOR MUTUAL RECOGNITION OF TEST CERTIFICATES FOR ELECTRICAL EQUIPMENT (IECEE) CB SCHEME SYSTEME CEI DACCEPTATION MUTUELLE DE CERTIFICATS DESSAIS DES EQUIPEMENTS ELECTRIQUES (IECEE) METHODE OC CB TEST CERTIFICATE CERTIFICAT D'ESSAI OC Product Produit Name and address of the applicant Nom et adresse du demandeur Name and address of the manufacturer Nom et adresse du fabricant Name and address of the factory Nom et adresse de l'usine Note: When more than one factory, please report on page 2 Note: Lorsque il y plus d'une usine, veuillez utiliser la deuxième page Ratings and principal characteristics Valeurs nominales et caractéristiques principales Trademark (if any) Marque de fabrique (si elle existe) AC/DC and DC/DC switching power supply Bel Fuse Inc. 206 Van Vorst St. Jersey City, NJ USA Bel Fuse Inc. 206 Van Vorst St. Jersey City, NJ USA Bel Power Solutions, s.r.o. Areal ZTS Dubnica nad Vahom Slovakia Additional information on page 2 Input: A or A, Vac, 50/60Hz / A or A, Vdc Type of Manufacturer s Testing Laboratories used Type de programme du laboratoire d essais constructeur Model / Type Ref. Ref. De type LK Series Additional information (if necessary may also be reported on page 2) Les informations complémentaires (si nécessaire, peuvent être indiqués sur la deuxième page A sample of the product was tested and found to be in conformity with Un échantillon de ce produit a été essayé et a été considéré conforme à la As shown in the Test Report Ref. No. which forms part of this Certificate Comme indiqué dans le Rapport dessais numéro de référence qui constitue partie de ce Certificat Output: One or two output; 28.25Vdc Max., 20A Max. Output power: 150W Max. Additional information on page 2 IEC (ed.2);am1;am This CB Test Certificate is issued by the National Certification Body Ce Certificat dessai OC est établi par l'organisme National de Certification Gaustadalléen 30 NO-0373 Oslo, Norway Date: Signature: Juan Z. Kleppenes Certification Department Issued /1

9 Ref. Certif. No. NO87303 IEC SYSTEM FOR MUTUAL RECOGNITION OF TEST CERTIFICATES FOR ELECTRICAL EQUIPMENT (IECEE) CB SCHEME SYSTEME CEI DACCEPTATION MUTUELLE DE CERTIFICATS DESSAIS DES EQUIPEMENTS ELECTRIQUES (IECEE) METHODE OC CB TEST CERTIFICATE CERTIFICAT D'ESSAI OC Product Produit Name and address of the applicant Nom et adresse du demandeur Name and address of the manufacturer Nom et adresse du fabricant Name and address of the factory Nom et adresse de l'usine Note: When more than one factory, please report on page 2 Note: Lorsque il y plus d'une usine, veuillez utiliser la deuxième page Ratings and principal characteristics Valeurs nominales et caractéristiques principales Trademark (if any) Marque de fabrique (si elle existe) AC/DC and DC/DC switching power supply Bel Fuse Inc. 206 Van Vorst St. Jersey City, NJ USA Bel Fuse Inc. 206 Van Vorst St. Jersey City, NJ USA Bel Power Solutions, s.r.o. Areal ZTS Dubnica nad Vahom Slovakia Additional information on page 2 Input: A or A, Vac, 50/60Hz / A or A, Vdc Type of Manufacturer s Testing Laboratories used Type de programme du laboratoire d essais constructeur Model / Type Ref. Ref. De type LS Series Additional information (if necessary may also be reported on page 2) Les informations complémentaires (si nécessaire, peuvent être indiqués sur la deuxième page A sample of the product was tested and found to be in conformity with Un échantillon de ce produit a été essayé et a été considéré conforme à la As shown in the Test Report Ref. No. which forms part of this Certificate Comme indiqué dans le Rapport dessais numéro de référence qui constitue partie de ce Certificat Output: One or two output; 28.25Vdc Max., 20A Max. Output power: 100W Max. Additional information on page 2 IEC (ed.2);am1;am This CB Test Certificate is issued by the National Certification Body Ce Certificat dessai OC est établi par l'organisme National de Certification Gaustadalléen 30 NO-0373 Oslo, Norway Date: Signature: Juan Z. Kleppenes Certification Department Issued /1

10 Ref. Certif. No. NO87304 IEC SYSTEM FOR MUTUAL RECOGNITION OF TEST CERTIFICATES FOR ELECTRICAL EQUIPMENT (IECEE) CB SCHEME SYSTEME CEI DACCEPTATION MUTUELLE DE CERTIFICATS DESSAIS DES EQUIPEMENTS ELECTRIQUES (IECEE) METHODE OC CB TEST CERTIFICATE CERTIFICAT D'ESSAI OC Product Produit Name and address of the applicant Nom et adresse du demandeur Name and address of the manufacturer Nom et adresse du fabricant Name and address of the factory Nom et adresse de l'usine Note: When more than one factory, please report on page 2 Note: Lorsque il y plus d'une usine, veuillez utiliser la deuxième page Ratings and principal characteristics Valeurs nominales et caractéristiques principales Trademark (if any) Marque de fabrique (si elle existe) AC/DC and DC/DC switching power supply Bel Fuse Inc. 206 Van Vorst St. Jersey City, NJ USA Bel Fuse Inc. 206 Van Vorst St. Jersey City, NJ USA Bel Power Solutions, s.r.o. Areal ZTS Dubnica nad Vahom Slovakia Additional information on page 2 Input: A, Vac, 50/60Hz Cl.I Type of Manufacturer s Testing Laboratories used Type de programme du laboratoire d essais constructeur Model / Type Ref. Ref. De type LKPSeries Additional information (if necessary may also be reported on page 2) Les informations complémentaires (si nécessaire, peuvent être indiqués sur la deuxième page A sample of the product was tested and found to be in conformity with Un échantillon de ce produit a été essayé et a été considéré conforme à la As shown in the Test Report Ref. No. which forms part of this Certificate Comme indiqué dans le Rapport dessais numéro de référence qui constitue partie de ce Certificat Output: One or two output: Vdc Max., 20A Max; output power: 280W Max. Additional information on page 2 IEC (ed.2);am1;am This CB Test Certificate is issued by the National Certification Body Ce Certificat dessai OC est établi par l'organisme National de Certification Gaustadalléen 30 NO-0373 Oslo, Norway Date: Signature: Juan Z. Kleppenes Certification Department Issued /1

11 Test Report issued under the responsibility of TEST REPORT IEC Information technology equipment Safety Part 1: General requirements Report Number.... : Date of issue...: 1 July, 2015 Total number of pages Applicant s name... : Bel Fuse Inc. Address...: 206 Van Vorst St., Jersey City, NJ, USA Test specification: Standard...: IEC :2005 (Second Edition) + Am 1: Am 2:2013 Test procedure...: Non-standard test method...: CB-Scheme N/A Test Report Form No.... : Test Report Form(s) Originator...: IEC60950_1F SGS Fimko Ltd Master TRF...: Dated Copyright 2014 IEC System of Conformity Assessment Schemes for Electrotechnical Equipment and Components (IECEE System). All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02. General disclaimer: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing CB Testing Laboratory. The authenticity of this Test Report and its contents can be verified by contacting the NCB, responsible for this Test Report. This Test Report, when bearing the Nemko name and logo is only valid when issued by a Nemko laboratory, or by a laboratory having special agreement with Nemko.

12 Page 2 of 59 Report No Test item description... : AC/DC and DC/DC switching power supply Trade Mark... : Manufacturer... : Model/Type reference... : Ratings... : Same as Applicant LKP, LK, LS Series For further information, please refer to General Product Information. Input LKP series: Vac, A, 50/60 Hz ; LK series : Vac, A or A, 50/60 Hz / Vdc, A or A ; LS series : Vac, A or A, 50/60 Hz / Vdc, A or A Output One or two output ; Vdc Max. ; 20 A Max. ; Output power: LKP: 280 W Max., LK : 150 W Max., LS : 100 W Max. For further information, please refer to General Product Information. Testing procedure and testing location: CB Testing Laboratory: Nemko USA Inc. Testing location/ address... : 2210 Faraday Ave. Suite 150, Carlsbad, CA 92008, USA Associated CB Testing Laboratory: Testing location/ address... : Tested by (name + signature)... : George Daverin Approved by (name + signature)... : Jeff Busch Report History: Original report TRF No. IEC60950_1F

13 Page 3 of 59 Report No List of Attachments (including a total number of pages in each attachment): Attachment 1: European Group Differences and National Deviations pages Documented deviations contain individual national documents for several European countries that are included in the European Group Deviations. The European Group Difference: EN60950:2006/A11:2009/A:2010/A12:2011/A2:2013 are considered Normative. The individual national documents (Denmark, Finland, Germany, Ireland, Norway, Spain, Sweden, Switzerland and United Kingdom) are considered informative and included at the manufacturer s request. Attachment 2: Miscellaneous Documentation, e.g. Photos, PWB Layout, Schematic etc pages (Not for publication Engineering use only) Summary of testing General Power supply All comments relate to all models, unless specifically stated. The equipment is an enclosed, Class I switch mode power supply with universal AC input and DC input, and single/dual DC voltage output for building-in. This report covers multiple models and all comments / tests apply to all models unless otherwise indicated. Testing was conducted on various models as indicated. 1.5, 3.2.5; Power supply cord set. A power supply cord set is not provided with the power supply. A power supply cord set, complying with the national regulations of the country in which the product is to be sold, shall be provided with the end-use equipment ; Safety instructions. Instructions and equipment markings related to safety are to be provided in a language, which is acceptable in the country in which the equipment is to be sold. English language verified ; IT power distribution systems. The equipment complies with the requirements for connection to the Norwegian IT power systems. The following information should be given (but is not required) in the installation instruction: This product is also designed for IT power system with Phase to Phase voltage 230V ; Number and location of protective devices. In Norway, IT power distribution system is used. Equipment with a single protective device is accepted in Norway. Other countries may have additional requirements ; Warning to service personnel. After operation of the protective device, the equipment is still under voltage if it is connected to an IT-power system. A warning is required for service personnel. Norway does not require this warning. 5.2: Electric Strength test Increased test voltages for Basic insulation applied to the equipment, based on measured working voltages. TRF No. IEC60950_1F

14 Page 4 of 59 Report No Summary of testing: Tests performed (name of test and test clause): 1) Input Test ) Durability Test ) Capacitance Discharge Test ) SELV Reliability Test ) Protective Bonding Test ) Humidity Test ) Working Voltage Measurement ) Hazardous Voltage Measurement ) Heating Test ) Touch Current Test ) Electric Strength Test ) Component Failure Test ) Abnormal Operation Test ) PS Output Overload and Short Test Testing location: See page 2 Summary of compliance with National Differences: List of countries addressed Austria (AT), Australia (AU), Canada (CA), Denmark (DK), Finland (FI), Germany (DE), Ireland (IE), Israel (IS), Korea (KR), Norway (NO), Slovenia (SI), Spain (ES), Sweden (SE), Switzerland (CH), United Kingdom (GB), United States of America (US) The product fulfils the requirements of : EN : A11: A1: A12: A2:2013 TRF No. IEC60950_1F

15 Page 5 of 59 Report No Copy of marking plate: The artwork below may be only a draft. The use of certification marks on a product must be authorized by the respective Certification Bodies that own these marks. TRF No. IEC60950_1F

16 Page 6 of 59 Report No Calibration Measurement uncertainty Evaluation of results All instruments used in the tests given in this test report are calibrated and traceable to national or international standards. Further information about traceability will be given on request. Measurement uncertainties are calculated for all instruments and instrument set-ups given in this report. Calculations are based on the principles given in the standard EA-4/02 (Dec. 1999), IEC Guide 115:2007, Nemko routine L227 and other relevant internal Nemko-procedures. Further information about measurement uncertainties will be given on request. If not explicitly stated otherwise in the standard, the test is passed if the measured value is equal to or below (above) the limit line, regardless of the measurement uncertainty. If the measured value is above (below) the limit line, the test is not passed - ref IEC Guide 115:2007, and Nemko routine L220. The instrumentation accuracy is within limits agreed by IECEE-CTL (ref. Nemko routine L227). TRF No. IEC60950_1F

17 Page 7 of 59 Report No Test item particulars: Equipment mobility... : [] movable [] hand-held [] transportable [] stationary [ X ] for building-in [] direct plug-in Connection to the mains... : Operating condition... : [] pluggable equipment [] type A [] type B [] permanent connection [] detachable power supply cord [] non-detachable power supply cord [ X ] not directly connected to the mains [ X ] continuous [] rated operating / resting time: Access location... : [] operator accessible [] restricted access location Over voltage category (OVC)...: [] OVC I [ X ] OVC II [] OVC III [] OVC IV [] other: Mains supply tolerance (%) or absolute mains supply values... : LK and LS series: Vac / Vdc LKP series: Vac Tested for IT power systems... : [ X ] Yes, IT Norway [] No IT testing, phase-phase voltage (V)... : Norway, 230V phase to phase voltage Class of equipment...: [ X ] Class I [] Class II [] Class III [] Not classified Considered current rating of protective device as part of the building installation (A)...: 20 A (USA) and 16 A (Europe) Pollution degree (PD)...: [] PD 1 [ X ] PD 2 [] PD 3 IP protection class... : Altitude during operation (m)... : Altitude of test laboratory (m)... : IP30 except with Option R, D and V with potetiometer adjustment 2000 m 94 m Mass of equipment (kg)... : 1.2 Temperature, Ambient ( C)... : 71 C, see condition of acceptability Possible test case verdicts: - test case does not apply to the test object... : N/A - test object does meet the requirement... : P (Pass) - test object does not meet the requirement... : F (Fail) Testing... : Date of receipt of test item... : May 2015 Date (s) of performance of tests... : June 2015 TRF No. IEC60950_1F

18 Page 8 of 59 Report No General remarks: "(See Enclosure #)" refers to additional information appended to the report. "(See appended table)" refers to a table appended to the report. Throughout this report a comma / point is used as the decimal separator. Manufacturer s Declaration per sub-clause of IECEE 02: The application for obtaining a CB Test Certificate includes more than one factory location and a declaration from the Manufacturer stating that the sample(s) submitted for evaluation is (are) representative of the products from each factory has been provided.. : Yes Not applicable When differences exist; they shall be identified in the General product information section. Name and address of factory (ies)... : Bel Power Solutions s.r.o. ArealZTS Dubnica n.vahom c Dubnica nad Vahom SLOVAKIA General product information: This test report is based on a TUV SUD test report Ref. No. SI with appended CB cert Ref. No. DE evaluated to the requirements of IEC :2005 (Second Edition) + Am 1: Am 2:2013. This test report includes the addition of a new Trade Mark, evaluation of the power supply to the requirements of IT power systems and an engineering evaluation of the Leakage at the output of the PSU. For continuity, data from the original TUV report is included in this report, along with the additional evaluation referenced. The input voltage is fed via an input fuse, an input filter, a rectifier and an inrush current limiter to a single transistor boost converter. This converter provides a sinusoidal input current (IEC/EN , class D equipment) and sources a capacitor with a voltage of VDC. This capacitor sources a single transistor forward converter. Each output is powered by a separate secondary winding on the main transformer. The resultant voltages are rectified and their ripples smoothed by a power choke and outputs filter. The control logic senses the main output voltage Uo1 and generates, with respect to the maximum admissible output currents, the control signal for the primary switching transistor. The second output of double output units is controlled by the main output but has independent current limiting. If the main output is driven into current limitation, the second output voltage will fall as well and vice versa. An auxiliary converter delivers the voltages for all main functions. MODEL DIFFERENCES: Three different main PCB s are used. For single output K and S models, double output K and S models and LKP models. The main transformers feature an UL recognized isolation system (MF1 or MH1). The transformers are equal for each output voltage in S/K 4xxx and S/K5xxx models and LKP models. TRF No. IEC60950_1F

19 Page 9 of 59 Report No Ratings: Type Input, A Output,DC Total Output Power (W) Max. V A Hz Output 1 Output 2 LKP /60 Max V, Max V, Max. 5.8 A Max. 5.8 A 280 There are two outputs. If you put them in parallel you can provide one output with max. output current. (LKP 5660) If you put them in series you can provide one output with max. output voltage. (LKP 5740) Alternatively both models can have a base plate instead of the heat sink. LK Vac A 50/60 Hz Vdc N/A 150 LK 5000 LS 4000 LS Vdc Vac Vdc Vac Vdc Vac Vdc A 50/60 Hz A 50/60 Hz A 50/60 Hz Max. 20 A Vdc Max. 6 A Vdc Max. 16 A Vdc Max. 4.2 A Vdc Max. 6 A 150 N/A Vdc Max. 4.2 A There are two outputs in x5000. If you put them in series you can provide one output with max. output voltage 56.5V. (LK574x-7R). Model differences: The S version has a smaller heat sink version than the K version. Alternatively both models can have a base plate for mounting to another heat sink in the end product instead of the heat sink. Refer to list of safety critical components. 100 TRF No. IEC60950_1F

20 Page 10 of 59 Report No Nomenclature: ab cdee-fgg (e.g.: LK ER) ab can be: LK LS LKP And means input voltage range and describes the series: The S-version is smaller than the K-version. The S-version has a smaller heat sink, and less power. Input voltage ranges: Vdc or Vac Input voltage Vac, but 250 W power out. c can be: And means: d can be: And means output Voltage. 4 One output 0, 1, 2 5,1 Vdc 5 Two outputs 3 12 Vdc 6 or higher Customer specific models: Some only with mechanical changes (e.g. other front plate, other LED s, and so on), some with other output voltages (e.g.: 13 V), and there are some with smaller input voltage range but up to 280 W output power. Not safety Relevant. 4, 5 15 Vdc 6 24 Vdc 7, 8 may be followed by Customer specific products with output voltages between 2 and 28,25Vd.c. Other specifications for single output models. And means (for models with two outputs; ee can be: f can be: And means ambient range: except customer specific models): Vdc; 12 Vdc -5 up to 51 C Vdc; 15 Vdc -6 up to 60 C Vdc; 24 Vdc to 71 C Customer specific products may have different output rating to 71 C Other specifications and additional -0, -1, -2, -3 features or -4 Customer specific models gg can be: And means auxiliary functions and options: E 1 R 2 Inrush current limitation Output voltage control input P 2 Potentiometer (output voltage adjustment ) D 3 Save data signal (D0...DD, to be specified) V 3,4 ACFAIL signal (V2, V3) T Current sharing B1 Cooling plate standard case B2 Cooling plate for long case 220 mm K H15S2 connector replaced by H15S4 (only models with 5 V output) 1... Option E is available for all models; mandatory for all -9 model types Feature R excludes option P and vice versa Option D excludes option V and vice versa Option V is available for LK/LS 4000 types with 5 V outputs. TRF No. IEC60950_1F

21 Page 11 of 59 Report No CONDITIONS OF ACCEPTABILITY: Model(s) require: 1) The products were tested on a 20 A (USA) and a 16 A (IEC) branch circuit in series. External circuit breaker did not open during the testing. The unit is approved for TN mains star connections and mains with 230 Vac phase to phase voltages. 2) All secondary output circuits are separated from mains by reinforced insulation and rated SELV non hazardous energy levels for one output. Both outputs together exceed the limit of 240 VA in LKP models. 3) The input and output connector was evaluated for factory wiring. 4) The power supply is rated class I. The power supply shall be properly bonded to the main protective bonding termination in the end product. The earth leakage current is below 3.5 ma. 5) The equipment has been evaluated for use in a Pollution Degree 2 and overvoltage category II environment and a maximum altitude of 2000 m. 6) Max. ambient temperature is 71 C for -7 models, 60 C for -6 models, 51 C for -5 models. Refer to nomenclature. 7) Disconnect device is considered end product evaluation. 8) Transformers TR1 (main board), TR81, TR71, TR72 (auxiliary converter board) provide reinforced insulation primary to secondary. 9) Unit fulfils requirements for fire enclosure. Abbreviations used in the report: - normal conditions... N.C. - single fault conditions... S.F.C - functional insulation... OP - basic insulation... BI - double insulation... DI - supplementary insulation... SI - between parts of opposite polarity... BOP - reinforced insulation... RI Indicate used abbreviations (if any):... None TRF No. IEC60950_1F