AC/DC ADAPTER DELTA ELECTRONICS INC 3 TUNGYUAN RD CHUNGLI INDUSTRIAL ZONE TAOYUAN COUNTY TAIWAN

Transcription

1 Ref. Certif. No. DK UL IEC SYSTEM FOR MUTUAL RECOGNITION OF TEST CERTIFICATES FOR ELECTRICAL EQUIPMENT (IECEE) CB SCHEME SYSTEME CEI D ACCEPTATION MUTUELLE DE CERTIFICATS D ESSAIS DES EQUIPEMENTS ELECTRIQUES (IECEE) METHODE OC CB TEST CERTIFICATE Product Produit Name and address of the applicant Nom et adresse du demandeur Name and address of the manufacturer Nom et adresse du fabricant Name and address of the factory Nom et adresse de l usine Note: When more than one factory, please report on page 2 Note: Lorsque il y plus d'une usine, veuillez utiliser la 2ème page Ratings and principal characteristics Valeurs nominales et caractéristiques principales Trademark (if any) Marque de fabrique (si elle existe) Type of Manufacturer's Testing Laboratories used Type de programme du laboratoire d'essais constructeur Model / Type Ref. Ref. De type Additional information (if necessary may also be reported on page 2) Les informations complémentaires (si nécessaire,, peuvent être indiqués sur la 2ème page A sample of the product was tested and found to be in conformity with Un échantillon de ce produit a été essayé et a été considéré conforme à la As shown in the Test Report Ref. No. which forms part of this Certificate Comme indiqué dans le Rapport d essais numéro de référence qui constitue partie de ce Certificat CERTIFICAT D ESSAI OC AC/DC ADAPTER DELTA ELECTRONICS INC 3 TUNGYUAN RD CHUNGLI INDUSTRIAL ZONE TAOYUAN COUNTY TAIWAN DELTA ELECTRONICS INC 3 TUNGYUAN RD CHUNGLI INDUSTRIAL ZONE TAOYUAN COUNTY TAIWAN DELTA ELECTRONICS (THAILAND) PUBLIC CO., LTD. 909 SOI 9 MOO 4, BANGPOO INDUSTRIAL ESTATE (E.P.Z.), PATTANA 1 RD., TAMBOL PHRAKSA, AMPHUR MUANG, SAMUTPRAKARN THAILAND Additional Information on page 2 Input: V~, 1.5 A, Hz Output: 19 Vdc, 4.74 A DELTA ELECTRONICS, INC. TMP ADP-90MD H Additionally evaluated to EN :2006 /A11:2009 /A1:2010 /A12:2011 /A2:2013; National Differences specified in the CB Test Report. Additional Information on page 2 IEC (ed.2), IEC (ed.2);am1, IEC (ed.2);am2 E A1694-CB-2 issued on This CB Test Certificate is issued by the National Certification Body Ce Certificat d essai OC est établi par l Organisme National de Certification Date: Signature: UL (US), 333 Pfingsten Rd IL 60062, Northbrook, USA UL (Demko), Borupvang 5A DK-2750 Ballerup, DENMARK UL (JP), Marunouchi Trust Tower Main Building 6F, Marunouchi, Chiyoda-ku, Tokyo , JAPAN UL (CA), 7 Underwriters Road, Toronto, M1R 3B4 Ontario, CANADA For full legal entity names see Jan-Erik Storgaard 1/2

2 Ref. Certif. No. DK UL Factories: DELTA ELECTRONICS POWER (DONGGUAN) CO., LTD. DELTA INDUSTRIAL ESTATE, SHIJIE TOWN, DONGGUAN CITY, GUANGDONG PROVINCE CHINA DELTA ELECTRONICS (JIANGSU) LTD. NO. 1688, JIANGXING EAST ROAD, WUJIANG ECONOMIC DEVELOPMENT ZONE, WUJIANG CITY, JIANGSU PROVINCE, CHINA Additional information (if necessary) Information complémentaire (si nécessaire) UL (US), 333 Pfingsten Rd IL 60062, Northbrook, USA UL (Demko), Borupvang 5A DK-2750 Ballerup, DENMARK UL (JP), Marunouchi Trust Tower Main Building 6F, Marunouchi, Chiyoda-ku, Tokyo , JAPAN UL (CA), 7 Underwriters Road, Toronto, M1R 3B4 Ontario, CANADA For full legal entity names see Date: Signature: Jan-Erik Storgaard 2/2

3 Issue Date: Page 1 of 63 Report Reference # E A1694-CB-2 Test Report issued under the responsibility of: Report Reference No... : TEST REPORT IEC Information technology equipment - Safety - Part 1: General requirements E A1694-CB-2 Date of issue... : Total number of pages... : 63 CB Testing Laboratory... : Address... : Applicant's name... : Address... : Test specification: Standard... : Test procedure... : Non-standard test method... : Test Report Form No.... : Test Report Form originator... : Underwriters Laboratories Taiwan Co., Ltd. 260 Da-Yeh Road, 112 Peitou Taipei City, Chinese Taipei DELTA ELECTRONICS INC 3 TUNGYUAN RD CHUNGLI INDUSTRIAL ZONE TAOYUAN COUNTY TAIWAN IEC :2005 (Second Edition); Am1: Am2:2013 CB Scheme IEC60950_1F SGS Fimko Ltd Master TRF... : Dated Copyright 2014 Worldwide System for Conformity Testing and Certification of Electrotechnical Equipment and Components (IECEE), Geneva, Switzerland. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. If this test Report is used by non-iecee members, the IECEE/IEC logo and the reference to the CB Scheme procedure shall be removed. This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02. General disclaimer The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing CB Testing Laboratory. The authenticity of this Test Report and its contents can be verified by contacting the NCB, responsible for this Test Report. TRF No. IEC60950_1F

4 Issue Date: Page 2 of 63 Report Reference # E A1694-CB-2 Test item description... : Trade Mark... : Manufacturer... : Model/Type reference... : Ratings... : AC/DC ADAPTER DELTA ELECTRONICS, INC. DELTA ELECTRONICS INC 3 TUNGYUAN RD CHUNGLI INDUSTRIAL ZONE TAOYUAN COUNTY TAIWAN ADP-90MD H Input: V~, 1.5 A, Hz Output: 19 Vdc, 4.74 A TRF No. IEC60950_1F

5 Issue Date: Page 3 of 63 Report Reference # E A1694-CB-2 Testing procedure and testing location: [ ] CB Testing Laboratory Testing location / address... : [ ] Associated CB Test Laboratory [x] Testing location / address... : Tested by (name + signature)... : Approved by (name + signature)... : Testing Procedure: TMP/CTF Stage 1 Testing location / address... : Delta Electronics (Jiangsu) Ltd., No. 1688, Jiangxing East Road, Wujiang Economic Development Zone, Wujiang City, Jiangsu Province, China. Tested by (name + signature)... : Neilson Chiu Approved by (name + signature)... : David Chen [ ] Testing Procedure: WMT/CTF Stage 2 Testing location / address... : Tested by (name + signature)... : Witnessed by (name + signature).. : Approved by (name + signature)... : [ ] Testing Procedure: SMT/CTF Stage 3 or 4 Testing location / address... : Tested by (name + signature)... : Approved by (name + signature)... : Supervised by (name + signature). : [ ] Testing Procedure: RMT Testing location / address... : Tested by (name + signature)... : Approved by (name + signature)... : Supervised by (name + signature). : List of Attachments National Differences (57 pages) Enclosures (43 pages) Summary Of Testing Unless otherwise indicated, all tests were conducted at Delta Electronics (Jiangsu) Ltd., No. 1688, Jiangxing East Road, Wujiang Economic Development Zone, Wujiang City, Jiangsu Province, China.. Tests performed (name of test and test clause) Testing location / Comments TRF No. IEC60950_1F

6 Issue Date: Page 4 of 63 Report Reference # E A1694-CB-2 Input: Single-Phase (1.6.2) Energy Hazard Measurements ( , 2.1.2, ) Capacitance Discharge ( ) SELV Reliability Test Including Hazardous Voltage Measurements (2.2.2, 2.2.3, 2.2.4, Part ) Limited Current Circuit Measurement (2.4.1, 2.4.2) Humidity (2.9.1, 2.9.2, 5.2.2) Determination of Working Voltage; Working Voltage Measurement (2.10.2) Strain Relief (3.2.6, 4.2.1, 4.2.7) Steady Force ( ) Impact (4.2.5, 4.2.1, Part ) Drop (4.2.6, 4.2.1) Stress Relief (4.2.7, 4.2.1) Heating (4.5.1, , ) Touch Current (Single-Phase; TN/TT System) (5.1, Annex D) Electric Strength (5.2.2) Component Failure (5.3.1, 5.3.4, 5.3.7) Power Supply Output Short-Circuit/Overload (5.3.7) Summary of Compliance with National Differences: Countries outside the CB Scheme membership may also accept this report. List of countries addressed: AR, AT, AU, BE, BG, BY, CA, CH, CN, CS, CZ, DE, DK, ES, EU, FI, FR, GB, GR, HU, IE, IL, IN, IT, JP, KR, MY, NL, NO, NZ, PL, PT, RO, SA, SE, SG, SI, SK, UA, US, ZA TRF No. IEC60950_1F

7 Issue Date: Page 5 of 63 Report Reference # E A1694-CB-2 Copy of Marking Plate The artwork below may be only a draft. The use of certification marks on a product must be authorized by the respective NCBs that own these marks. TRF No. IEC60950_1F

8 Issue Date: Page 6 of 63 Report Reference # E A1694-CB-2 Test item particulars : Equipment mobility...: Connection to the mains...: Operating condition...: Access location...: Over voltage category (OVC)...: movable/ transportable pluggable A continuous operator accessible OVC II Mains supply tolerance (%) or absolute mains supply values...: +10%, -10% Tested for IT power systems...: IT testing, phase-phase voltage (V)...: Class of equipment...: No Considered current rating of protective device as part of the building installation (A)...: 20 Pollution degree (PD)...: PD 2 IP protection class...: Altitude of operation (m)...: Altitude of test laboratory (m)...: Class I (Functional Earthing) IP X0 UP to 5000m Up to 2000m Mass of equipment (kg)...: Approx Possible test case verdicts: - test case does not apply to the test object... : N / A - test object does meet the requirement... : P() - test object does not meet the requirement... : F(Fail) Testing: Date(s) of receipt of test item...: Date(s) of Performance of tests...: to General remarks: "(see Enclosure #)" refers to additional information appended to the report. "(see appended table)" refers to a table appended to the report. Throughout this report a point is used as the decimal separator. Manufacturer's Declaration per Sub Clause of IECEE 02: The application for obtaining a CB Test Certificate includes more than one factory and a declaration from the Manufacturer stating that the sample(s) submitted for evaluation is (are) representative of the products from each factory has been provided... Yes When differences exist, they shall be identified in the General Product Information section. Name and address of Factory(ies): DELTA ELECTRONICS (THAILAND) PUBLIC CO., LTD. 909 SOI 9 MOO 4, BANGPOO INDUSTRIAL ESTATE (E.P.Z.), PATTANA 1 RD., TAMBOL PHRAKSA, AMPHUR MUANG, SAMUTPRAKARN 10280, THAILAND. DELTA ELECTRONICS POWER (DONGGUAN) CO., LTD. TRF No. IEC60950_1F

9 Issue Date: Page 7 of 63 Report Reference # E A1694-CB-2 DELTA INDUSTRIAL ESTATE, SHIJIE TOWN, DONGGUAN CITY, GUANGDONG PROVINCE CHINA DELTA ELECTRONICS (JIANGSU) LTD. NO. 1688, JIANGXING EAST ROAD, WUJIANG ECONOMIC DEVELOPMENT ZONE, WUJIANG CITY, JIANGSU PROVINCE, CHINA GENERAL PRODUCT INFORMATION: Report Summary All applicable tests according to the referenced standard(s) have been carried out. Product Description Electronic components mounted on PWB and housed with a plastic enclosure. Model Differences Additional Information - This report is a reissue of CBTR Ref. No.: E A1694-CB-1, CB Test Certificate Ref. No.: DK UL. Based on the previously conducted testing and the review of product technical documentation including photos, schematics, wiring diagrams and similar, has been determined that the product continues to comply with the standard. - This report is reissued due to: Upgrade standard to IEC :2005: Am 1: Am 2: 2013/ - No tests conducted under this investigation due to reissue of CB Test Report Ref. No. E A1694-CB- 1. All required tests were carried out under the original investigation. - Test item receipt date ( ) and Test performance date ( to ) are the dates in CB report No. E A1694-CB-1. Technical Considerations The product was submitted and evaluated for use at the maximum ambient temperature (Tma) permitted by the manufacturer s specification of: 40 degree C The means of connection to the mains supply is: Pluggable A, Detachable power cord The product is intended for use on the following power systems: TN The equipment disconnect device is considered to be: Appliance inlet The product was investigated to the following additional standards: EN : A11: A1: A12: A2:2013 (which includes all European national differences, including those specified in this test report).,, The equipment is operated up to 5000 m (16404 feet) above sea level as declared by manufacturer. Clearances have been evaluated according to IEC : table A.2 with a multiplication factor of 1.48 throughout this report. The following are available from the Applicant upon request: Installation (Safety) Instructions / Manual TRF No. IEC60950_1F

10 Issue Date: Page 8 of 63 Report Reference # E A1694-CB-2 The equipment employs Functional Earthing per As anticipated by the NOTE for 1.2.4, it does not conform to one of the common Classes (I, II, or III). The following insulation is provided between the primary and accessible dead metal parts and circuits: Double, Reinforced Unless otherwise specified, all tests are performed on the equipment with installed F1 fuse, by EVER ISLAND ELECTRIC CO LTD & WALTER ELECTRIC, Type 2010, rated 250Vac/T3.15AL. -- Abbreviations used in the report: - normal condition...n.c. - single fault condition...s.f.c - operational insulation...op - basic insulation...bi - basic insulation between parts of opposite polarity: BOP - supplementary insulation...si - double insulation...di - reinforced insulation...ri Indicate used abbreviations (if any) TRF No. IEC60950_1F

11 Issue Date: Page 9 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 1 GENERAL 1.5 Components General Comply with IEC or relevant component standard (See Table 1.5.1) Evaluation and testing of components - Certified components are used in accordance with their ratings, certifications and they comply with applicable parts of this Standard. - Components, for which no relevant IEC-Standard exist, have been tested under the conditions occurring in the equipment, using applicable parts of IEC Components not certified are used in accordance with their ratings and they comply with applicable parts of IEC and the relevant component Standard Thermal controls Transformers Transformers comply with the relevant requirements of this standard, including those of Annex C Interconnecting cables INTERCONNECTING CABLES used complied with the relevant requirements of this standard Capacitors bridging insulation Line-to-neutral capacitors are subclass X1 or X2. Bridging capacitors bridging double insulation are subclass min. Y1. Capacitors used in accordance with their rating and complied with subclasses of IEC with at least 21 days damp heat test. TRF No. IEC60950_1F

12 Issue Date: Page 10 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict Resistors bridging insulation Resistors bridging functional, basic or supplementary insulation Resistors bridging double or reinforced insulation between a.c. mains and other circuits Resistors bridging double or reinforced insulation between a.c. mains and antenna or coaxial cable For functional insulation only. No resistors bridging double or reinforced insulation between a.c. mains and other circuits. No resistors bridging double or reinforced insulation between a.c. mains and antenna or coaxial cable Components in equipment for IT power systems Surge suppressors No surge suppressors General Protection of VDRs Bridging of functional insulation by a VDR Bridging of basic insulation by a VDR Bridging of supplementary, double or reinforced insulation by a VDR 1.6 Power interface AC power distribution systems AC power distribution systems are classified as TN Input current The steady state input current of the equipment did not exceed the RATED CURRENT by more than 10% under NORMAL LOAD Voltage limit of hand-held equipment Neutral conductor The neutral conductor was served as a line conductor. TRF No. IEC60950_1F

13 Issue Date: Page 11 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 1.7 Marking and instructions Power rating and identification markings Rating marking readily visible to OPERATOR Power rating mark Multiple mains supply connections... : Rated voltage(s) or voltage range(s) (V)... : Symbol for nature of supply, for d.c. only... : Rated frequency or rated frequency range (Hz)... : Rated current (ma or A)... : 1.5A Identification markings Manufacturer's name or trademark or identification mark... : Model identification or type reference... : ADP-90MD H Symbol for Class II equipment only... : DELTA ELECTRONICS, INC. or E Other markings and symbols... : Additional symbols/markings do not give rise to misunderstanding Use of graphical symbols Safety instructions and marking Operating/safety instructions made available to the USER General Disconnect devices Appliance inlet is provided as disconnection device Overcurrent protective device IT Power distribution systems Investigation in national approval Operator access with a tool Ozone Short duty cycles Equipment is designed for continuous operation Supply voltage adjustment... : Full range circuit. Method and means of adjustment; reference to installation instructions... : Power outlets on the equipment... : No outlets Fuse identification (marking, special fusing characteristics, cross-reference)... : Fuse marking on PWB near fuse: F1 T3.15AL/250V Wiring terminals TRF No. IEC60950_1F

14 Issue Date: Page 12 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict Protective earthing and bonding terminals... : Terminals for a.c. mains supply conductors Terminals for d.c. mains supply conductors Controls and indicators No controls and indicators Identification, location and marking... : Colours... : Symbols according to IEC : There are no switches in the equipment Markings using figures... : Isolation of multiple power sources... : Only one mains connection Thermostats and other regulating devices... : No adjustable thermostats or similar regulating devices Durability All markings provided on UL Recognized Component labels Removable parts No removable parts Replaceable batteries... : There are no lithium batteries in the equipment. Language(s)... : Equipment for restricted access locations... : Not intended for use in a restricted access location. TRF No. IEC60950_1F

15 Issue Date: Page 13 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 2 PROTECTION FROM HAZARDS 2.1 Protection from electric shock and energy hazards Protection in operator access areas Access to energized parts The OPERATOR cannot access to energized parts except for specified in subclause Test by inspection... : The OPERATOR cannot contact with any parts with only BASIC INSULATION to ELV CIRCUITS or HAZARDOUS VOLTAGES. Test with test finger (Figure 2A)... : The test finger cannot contact with any parts with only BASIC INSULATION to ELV CIRCUITS or HAZARDOUS VOLTAGES. Test with test pin (Figure 2B)... : The test pin cannot contact with bare parts at HAZARDOUS VOLTAGES. Test with test probe (Figure 2C)... : No TNV presents Battery compartments Access to ELV wiring Working voltage (Vpeak or Vrms); minimum distance through insulation (mm)... : Access to hazardous voltage circuit wiring Energy hazards... : The output of the power supply is not an energy hazard. (See Table for details) Manual controls Discharge of capacitors in equipment The voltage across-line capacitors did decay to less than 37 percent of its original value in 1.0 second. Measured voltage (V); time-constant (s)... : Test Voltage: 264 Vac, 60 Hz: Fuse in, Vo=366 Vpk, Vtc=130 Vpk less 135 Vpk (37 percent of its original value) in 1.0 second. CX1=0.33uF, CX2=0.47uF, R1=R2=590K ohm - - TRF No. IEC60950_1F

16 Issue Date: Page 14 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict Energy hazards - d.c. mains supply No connection to d.c. mains. a) Capacitor connected to the d.c. mains supply.. : b) Internal battery connected to the mains supply : Audio amplifiers... : No audio amplifiers Protection in service access areas Protection in restricted access locations 2.2 SELV circuits General requirements Voltages under normal conditions (V)... : All accessible voltages are less than 42.4 V peak or 60 V dc and are classified as SELV Voltages under fault conditions (V)... : Under fault conditions voltages never exceed 71V peak and 120Vdc and do not exceed 42.4V peak or 60V dc for more than 0.2 sec Connection of SELV circuits to other circuits... : SELV circuits are only connected to other secondary circuits. SELV circuit and all interconnected circuits separated from primary by Double/Reinforced insulation. The SELV circuit does not exceed the SELV limits under normal and fault conditions. TRF No. IEC60950_1F

17 Issue Date: Page 15 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 2.3 TNV circuits Limits No TNV presents. Type of TNV circuits... : Separation from other circuits and from accessible parts General requirements Protection by basic insulation Protection by earthing Protection by other constructions... : Separation from hazardous voltages Insulation employed... : Connection of TNV circuits to other circuits Insulation employed... : Test for operating voltages generated externally 2.4 Limited current circuits General requirements Conduct the test for clause (Tested by Annex D.1 measuring instrument) Limit values 0.7mA Frequency (Hz)... : -- - Measured current (ma)... : max. 0.12mA - Measured voltage (V)... : -- - Measured circuit capacitance (nf or µf)... : <0.1uF Connection of limited current circuits to other circuits See TRF No. IEC60950_1F

18 Issue Date: Page 16 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 2.5 Limited power sources a) Inherently limited output b) Impedance limited output c) Regulating network limited output under normal operating and single fault condition Use of integrated circuit (IC) current limiters... : - d) Overcurrent protective device limited output Max. output voltage (V), max. output current (A), max. apparent power (VA)... : Current rating of overcurrent protective device (A) : - - TRF No. IEC60950_1F

19 Issue Date: Page 17 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 2.6 Provisions for earthing and bonding Protective earthing Functional earthing Functional earthing separated from Hazardous voltage by double/reinforced insulation. Use of symbol for functional earthing... : Protective earthing and protective bonding conductors Insulation on functional earthing conductor(s) is not green-yellow. For Power Supply Cord only General Size of protective earthing conductors Rated current (A), cross-sectional area (mm²), AWG... : 1.5A, min. 0.75mm2, min. 18AWG Size of protective bonding conductors Rated current (A), cross-sectional area (mm²), AWG... : Protective current rating (A), cross-sectional area (mm²), AWG... : Resistance of earthing conductors and their terminations; resistance (ohm), voltage drop (V), test current (A), duration (min)... : Colour of insulation... : Terminals General Protective earthing and bonding terminals Rated current (A), type, nominal thread diameter (mm)... : Separation of the protective earthing conductor from protective bonding conductors Only used Appliance Inlet as main protective earthing terminal Integrity of protective earthing Interconnection of equipment Components in protective earthing conductors and protective bonding conductors Disconnection of protective earth Parts that can be removed by an operator TRF No. IEC60950_1F

20 Issue Date: Page 18 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict Parts removed during servicing Corrosion resistance Screws for protective bonding Reliance on telecommunication network or cable distribution system 2.7 Overcurrent and earth fault protection in primary circuits Basic requirements Protection in PRIMARY CIRCUITS is an integral part of the equipment. Instructions when protection relies on building installation Pluggable Type A Faults not covered in Protection against faults covered in 5.3 is fitted as an integral part of the equipment Short-circuit backup protection The building installation is considered as providing shortcircuit backup protection for PLUGGABLE EQUIPMENT TYPE A Number and location of protective devices... : One protective device in the "LIVE" phase Protection by several devices Warning to service personnel... : TRF No. IEC60950_1F

21 Issue Date: Page 19 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 2.8 Safety interlocks General principles No SAFETY INTERLOCKS used Protection requirements Inadvertent reactivation Fail-safe operation Protection against extreme hazard Moving parts Overriding Switches, relays and their related circuits Separation distances for contact gaps and their related circuits (mm)... : Overload test Endurance test Electric strength test Mechanical actuators 2.9 Electrical insulation Properties of insulating materials Electric Strength Test of was performed after the Humidity Treatment of Humidity conditioning Humidity treatment performed for a period of 120 hours. The following transformers also tested with 120 hours: T1 (See Table for the mfr. and type) Relative humidity (%), temperature ( C)... : 93%, 40 degree C Grade of insulation FUNCTIONAL, BASIC, SUPPLEMENTARY and REINFORCED or DOUBLE INSULATION applicable per Table 2H Separation from hazardous voltages See below Method(s) used... : Method 1 - TRF No. IEC60950_1F

22 Issue Date: Page 20 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 2.10 Clearances, creepage distances and distances through insulation General - Pollution degree 2 applicable Frequency... : less than 30k Hz Pollution degrees... : Pollution Degree 2 applicable Reduced values for functional insulation FUNCTIONAL INSULATION complied with Sub-clause Intervening unconnected conductive parts Insulation with varying dimensions Special separation requirements Insulation in circuits generating starting pulses Determination of working voltage General RMS working voltage See Table for details Peak working voltage See Table for details Clearances (see appended table and ) General Mains transient voltages a) AC mains supply... : Category II b) Earthed d.c. mains supplies... : c) Unearthed d.c. mains supplies... : d) Battery operation... : Clearances in primary circuits See Table , for details Clearances in secondary circuits FUNCTIONAL INSULATION complied with Sub-clause Clearances in circuits having starting pulses Transients from a.c. mains supply... : 1500 Vpk assumed in secondary circuits Transients from d.c. mains supply... : Transients from telecommunication networks and cable distribution systems... : Measurement of transient voltage levels a) Transients from a mains supply For an a.c. mains supply... : TRF No. IEC60950_1F

23 Issue Date: Page 21 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict For a d.c. mains supply... : b) Transients from a telecommunication network Creepage distances See Table , for details General Material group and comparative tracking index CTI tests... : Material Group IIIb assumed unless otherwise indicated. 100 <= CTI < Minimum creepage distances Solid insulation General Distances through insulation See Table for details Insulating compound as solid insulation Semiconductor devices Optocoupler is an approved component Cemented joints Thin sheet material - General Separable thin sheet material Number of layers (pcs)... : See Table for details Non-separable thin sheet material Thin sheet material - standard test procedure Electric strength test... : Thin sheet material - alternative test procedure Electric strength test... : See Table for details Insulation in wound components Wire in wound components Approved triple-insulated winding wire used in the secondary winding of T1. Working voltage... : the peak working voltage exceeds 71V a) Basic insulation not under stress... : b) Basic, supplementary, reinforced insulation... : - c) Compliance with Annex U... : Triple insulation wires used. Two wires in contact inside wound component; angle between 45 and : Physical separation in the form of insulating sheet material to relieve mechanical stress at TRF No. IEC60950_1F

24 Issue Date: Page 22 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict Wire with solvent-based enamel in wound components the crossover point. Electric strength test... : - Routine test Additional insulation in wound components Working voltage... : - Basic insulation not under stress... : - Supplementary, reinforced insulation... : Construction of printed boards Uncoated printed board used Uncoated printed boards Clearances and creepage distance are complying with Cl and Coated printed boards No coated printed boards Insulation between conductors on the same inner surface of a printed board Insulation between conductors on different layers of a printed board Distance through insulation Number of insulation layers (pcs)... : Single layer PCB used Component external terminations Tests on coated printed boards and coated components Uncoated printed board used Sample preparation and preliminary inspection Thermal conditioning Electric strength test Abrasion resistance test Thermal cycling Test for Pollution Degree 1 environment and insulating compound Tests for semiconductor devices and cemented joints Enclosed and sealed parts TRF No. IEC60950_1F

25 Issue Date: Page 23 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 3 WIRING, CONNECTIONS AND SUPPLY 3.1 General Current rating and overcurrent protection Protection against mechanical damage The wires are well routed away from sharp edges, etc. and are adequately fixed to prevent excessive strain on wire and terminals Securing of internal wiring Insulation of conductors The insulation of the individual conductors is suitable for the application and the working voltage Beads and ceramic insulators Screws for electrical contact pressure Insulating materials in electrical connections Self-tapping and spaced thread screws Termination of conductors 10 N pull test With applying a pull force of 10 N, the conductor does not break away or pivot on its terminal to the extent that required CLEARANCE or CREEPAGE DISTANCES are reduced below the values required in Sleeving on wiring The sleeving used as supplementary insulation on internal wiring is retained by positive means. TRF No. IEC60950_1F

26 Issue Date: Page 24 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 3.2 Connection to mains supply Means of connection The unit is provided with an appliance inlet Connection to an a.c. mains supply Connection to a d.c. mains supply Multiple supply connections Permanently connected equipment Number of conductors, diameter of cable and conduits (mm)... : Appliance inlets Approved appliance inlet complying with IEC and UL 498, so placed that the connector can be inserted without difficulty and after insertion of the connector, the equipment is not supported by the connector for any position of normal use on a flat surface Power supply cords AC power supply cords Type... : See Table for details. - Rated current (A), cross-sectional area (mm²), AWG... : Rated 1.5A, min squared, min. 18 AWG DC power supply cords Cord anchorages and strain relief Mass of equipment (kg), pull (N)... : 0.32kg; 30N - Longitudinal displacement (mm)... : 0.93mm Protection against mechanical damage Cord guards Diameter of minor dimension D (mm); test mass (g)... : Radius of curvature of cord (mm)... : Supply wiring space TRF No. IEC60950_1F

27 Issue Date: Page 25 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 3.3 Wiring terminals for connection of external conductors Wiring terminals Connection of non-detachable power supply cords Screw terminals Conductor sizes to be connected Rated current (A), cord/cable type, cross-sectional area (mm²)... : Wiring terminal sizes Rated current (A), type and nominal thread diameter (mm)... : Wiring terminals design Grouping of wiring terminals Stranded wire Disconnection from the mains supply General requirement Disconnect devices The Appliance Inlet is used as the disconnect device Permanently connected equipment Parts which remain energized Switches in flexible cords No isolating switches fitted in flexible cords Number of poles - single-phase and d.c. equipment Disconnect device disconnects all poles simultaneously Number of poles - three-phase equipment Switches as disconnect devices Plugs as disconnect devices Interconnected equipment Multiple power sources TRF No. IEC60950_1F

28 Issue Date: Page 26 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 3.5 Interconnection of equipment General requirements Interconnection circuit did continued conformance to the requirements of SELV CIRCUITS Types of interconnection circuits... : SELV CIRCUITS are only connected to SELV CIRCUITS ELV circuits as interconnection circuits Data ports for additional equipment 4 PHYSICAL REQUIREMENTS 4.1 Stability Angle of 10 Less than 7kg Test force (N)... : Not floor standing. TRF No. IEC60950_1F

29 Issue Date: Page 27 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 4.2 Mechanical strength General Rack-mounted equipment Steady force test, 10 N The required DISTANCES does not reduced below the values required in Steady force test, 30 N Steady force test, 250 N No hazards as a result of the 250 N test Impact test Fall test Swing test Drop test; height (mm)... : No hazards as a result of the drop test Stress relief test After 7 hours at degree C and cooling down to room temperature, no shrinkage, distortion or loosening of any enclosure part was noticeable on the adapter Cathode ray tubes Picture tube separately certified... : High pressure lamps Wall or ceiling mounted equipment; force (N)... : TRF No. IEC60950_1F

30 Issue Date: Page 28 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 4.3 Design and construction Edges and corners All edges and corners judged to be sufficiently well rounded so as not to constitute a hazard Handles and manual controls; force (N)... : Adjustable controls Securing of parts Electrical and mechanical connections can be expected to withstand usual mechanical stress Connection by plugs and sockets IEC or IEC type connectors not used for SELV circuits Direct plug-in equipment Torque... : Compliance with the relevant mains plug standard: Heating elements in earthed equipment Batteries No batteries. - Overcharging of a rechargeable battery - Unintentional charging of a non-rechargeable battery - Reverse charging of a rechargeable battery - Excessive discharging rate for any battery Oil and grease Dust, powders, liquids and gases Containers for liquids or gases Flammable liquids... : Quantity of liquid (l)... : Flash point ( C)... : Radiation General Ionizing radiation Measured radiation (pa/kg)... : - Measured high-voltage (kv)... : - Measured focus voltage (kv)... : - CRT markings... : - TRF No. IEC60950_1F

31 Issue Date: Page 29 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict Effect of ultraviolet (UV) radiation on materials Part, property, retention after test, flammability classification... : Human exposure to ultraviolet (UV) radiation... : Lasers (including laser diodes) and LEDs Lasers (including laser diodes) Laser class... : Light emitting diodes (LEDs) Other types... : 4.4 Protection against hazardous moving parts General No hazardous moving part presents Protection in operator access areas... : Household and home/office document/media shredders Protection in restricted access locations... : Protection in service access areas Protection against moving fan blades General Not considered to cause pain or injury. a)... : Is considered to cause pain, not injury. b)... : Considered to cause injury. c)... : Protection for users Use of symbol or warning... : Protection for service persons Use of symbol or warning... : TRF No. IEC60950_1F

32 Issue Date: Page 30 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 4.5 Thermal requirements General Temperature tests The equipment and its components did not attain excessive temperatures during normal operation. (see Table 4.5) Normal load condition per Annex L... : Operated in the most unfavorable way of operation given in the operating instructions until steady conditions established Temperature limits for materials Touch temperature limits Resistance to abnormal heat... : Phenolic materials are used in bobbin of T Openings in enclosures Top and side openings Dimensions (mm)... : No openings within the whole enclosure Bottoms of fire enclosures Construction of the bottom, dimensions (mm)... : No openings within the whole enclosure Doors or covers in fire enclosures Openings in transportable equipment Constructional design measures Dimensions (mm)... : No openings provided Evaluation measures for larger openings Use of metallized parts Adhesives for constructional purposes Conditioning temperature ( C), time (weeks)... : TRF No. IEC60950_1F

33 Issue Date: Page 31 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 4.7 Resistance to fire Reducing the risk of ignition and spread of flame Method 1, selection and application of components wiring and materials Method 2, application of all of simulated fault condition tests Selection and application of components, wiring and materials, which reduce the possibility of ignition and spread of flame by the use of FIRE ENCLOSURE Conditions for a fire enclosure Parts requiring a fire enclosure A fire enclosure covers all parts Parts not requiring a fire enclosure Materials General The propagation of fire is minimized through satisfying the requirement of constructions and materials Materials for fire enclosures Protective enclosure with no decorative parts. Enclosure of this unit with flammability class V Materials for components and other parts outside fire enclosures Materials for components and other parts inside fire enclosures - All internal materials are min. V-2 or are mounted on a PWB min. V-1; - All Internal wiring is insulated with PVC, TFE, PTFE, FEP, neoprene, polyimide or marked VW-1 or FT Materials for air filter assemblies Materials used in high-voltage components TRF No. IEC60950_1F

34 Issue Date: Page 32 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 5 ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS 5.1 Touch current and protective conductor current General Configuration of equipment under test (EUT) The EUT provided only one connection to AC MAINS SUPPLY Single connection to an a.c. mains supply Redundant multiple connections to an a.c. mains supply Simultaneous multiple connections to an a.c. mains supply Test circuit Figure 5A applicable Application of measuring instrument Using the measuring instrument specified in annex D Test procedure Test measurements Supply voltage (V)... : See Table 5.1 for details - Measured touch current (ma)... : See Table 5.1 for details - Max. allowed touch current (ma)... : See Table 5.1 for details - Measured protective conductor current (ma)... : Not applicable - Max. allowed protective conductor current (ma)... : Not applicable Equipment with touch current exceeding 3,5 ma General... : Simultaneous multiple connections to the supply Touch currents to telecommunication networks and cable distribution systems and from telecommunication networks Limitation of the touch current to a telecommunication network or to a cable distribution system No TNV presents. Supply voltage (V)... : - Measured touch current (ma)... : - Max. allowed touch current (ma)... : Summation of touch currents from telecommunication networks a) EUT with earthed telecommunication ports... : b) EUT whose telecommunication ports have no TRF No. IEC60950_1F

35 Issue Date: Page 33 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict reference to protective earth 5.2 Electric strength General Based on the electric strength test the use of the insulating materials within the equipment is satisfactory Test procedure (See Table 5.2 for details) 5.3 Abnormal operating and fault conditions Protection against overload and abnormal operation Motors Transformers Compliance is checked by the applicable tests of Annex C Functional insulation... : Functional insulation complies with the requirements (a), (b), or (c) Electromechanical components Audio amplifiers in ITE... : Simulation of faults (See Table 5.3) Unattended equipment Compliance criteria for abnormal operating and fault conditions No fire, emission of molten metal, deformation, excessive temperature rises or insulation breakdown was detected during these tests During the tests No fire, emission of molten metal or deformation was noted during the tests After the tests Electric Strength tests performed after abnormal and fault tests. TRF No. IEC60950_1F

36 Issue Date: Page 34 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict 6 CONNECTION TO TELECOMMUNICATION NETWORKS 6.1 Protection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment Protection from hazardous voltages Separation of the telecommunication network from earth Requirements No TNV presents. Supply voltage (V)... : - Current in the test circuit (ma)... : Exclusions... : 6.2 Protection of equipment users from overvoltages on telecommunication networks Separation requirements Electric strength test procedure Impulse test Steady-state test Compliance criteria 6.3 Protection of the telecommunication wiring system from overheating Max. output current (A)... : - Current limiting method... : - 7 CONNECTION TO CABLE DISTRIBUTION SYSTEMS 7.1 General 7.2 Protection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment 7.3 Protection of equipment users from overvoltages on the cable distribution system 7.4 Insulation between primary circuits and cable distribution systems No connections to CABLE DISTRIBUTION SYSTEMS General Voltage surge test Impulse test TRF No. IEC60950_1F

37 Issue Date: Page 35 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict A ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE A.1 Flammability test for fire enclosures of movable equipment having a total mass exceeding 18 kg, and of stationary equipment (see ) A.1.1 Samples... : - Wall thickness (mm)... : - A.1.2 Conditioning of samples; temperature ( C)... : A.1.3 Mounting of samples... : A.1.4 Test flame (see IEC ) Flame A, B, C or D... : A.1.5 Test procedure A.1.6 Compliance criteria Sample 1 burning time (s)... : - Sample 2 burning time (s)... : - Sample 3 burning time (s)... : - A.2 Flammability test for fire enclosures of movable equipment having a total mass not exceeding 18 kg, and for material and components located inside fire enclosures (see and ) A.2.1 Samples, material... : - Wall thickness (mm)... : - A.2.2 Conditioning of samples; temperature ( C)... : A.2.3 Mounting of samples... : A.2.4 Test flame (see IEC ) Flame A, B or C... : - A.2.5 Test procedure A.2.6 Compliance criteria Sample 1 burning time (s)... : - Sample 2 burning time (s)... : - Sample 3 burning time (s)... : - A.2.7 Alternative test acc. to IEC , cl. 5 and 9 Sample 1 burning time (s)... : - Sample 2 burning time (s)... : - Sample 3 burning time (s)... : - A.3 Hot flaming oil test (see 4.6.2) A.3.1 Mounting of samples A.3.2 Test procedure TRF No. IEC60950_1F

38 Issue Date: Page 36 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict A.3.3 Compliance criterion B ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see and 5.3.2) B.1 General requirements No motors Position... : - Manufacturer... : - Type... : - Rated values... : - B.2 Test conditions B.3 Maximum temperatures B.4 Running overload test B.5 Locked-rotor overload test Test duration (days)... : - Electric strength test: test voltage (V)... : - B.6 Running overload test for d.c. motors in secondary circuits B.6.1 General B.6.2 Test procedure B.6.3 Alternative test procedure B.6.4 Electric strength test; test voltage (V)... : B.7 Locked-rotor overload test for d.c. motors in secondary circuits B.7.1 General B.7.2 Test procedure B.7.3 Alternative test procedure B.7.4 Electric strength test; test voltage (V)... : B.8 Test for motors with capacitors B.9 Test for three-phase motors B.10 Test for series motors Operating voltage (V)... : - TRF No. IEC60950_1F

39 Issue Date: Page 37 of 63 Report Reference # E A1694-CB-2 IEC Clause Requirement + Test Result - Remark Verdict C ANNEX C, TRANSFORMERS (see and 5.3.3) Position... : T1 - Manufacturer... : (See Table 1.5.1) - Type... : (See Table 1.5.1) - Rated values... : (See Table 1.5.1) - Method of protection... : Inherent impedance. - C.1 Overload test The excess temperatures on the windings did not exceed 175 degree C for a Class B system without triggering the protection device (F1). C.2 Insulation (see appended table 5.2) D Protection from displacement of windings... : Triple insulated wire used in transformer (T1). ANNEX D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS (see 5.1.4) D.1 Measuring instrument D.2 Alternative measuring instrument E ANNEX E, TEMPERATURE RISE OF A WINDING (see ) F ANNEX F, MEASUREMENT OF CLEARANCES AND CREEPAGE DISTANCES (see 2.10 and Annex G) TRF No. IEC60950_1F