TEST REPORT EN Safety of information technology equipment Part 1-General requirements

Transcription

1 TEST REORT E Safety of information technology equipment art 1-General requirements Report reference o... : R2XM A1-03 Compiled by (+ signature)... : Test Engineer: Acan Liang Approved by (+ signature)... : Team Leader: Robin He Date of issue... : Testing laboratory... : Bay Area Compliance Laboratories Corp. (Dongguan) Address... : o.69, ulongcun, uxinhu Industry Area, Tangxia Dongguan, Guangdong, China Testing location... : As above Applicant s name... : United GULF GATE Co. Address... : Aladel Tower, F21, Fahad Al Salem St., State of KUWAIT. Manufacturer s name... : Same as applicant Address... : Same as applicant Factory s name... : /A Address... : /A Standard... : E :2006+A11:2009+A1:2010+A12:2011+A2:2013 Test sample(s) received... : Test in period... : to rocedure deviation... : /A on-standard test method... : /A ote: The test data was only valid for the test sample(s). This test report is prepared for the customer shown above and for the specific product described herein. It must not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. (Dongguan). age 1 of 66

2 Report o.: R2XM A1-03 Test item description...: I Video Intercom Trademark...: Xontel Model/type reference...: XT-10 Manufacturer...: Same as applicant Rating... : EUT Input: 12.0V 1A, or OE port Copy of marking plate: The artwork below may be only a draft. The use of certification marks on a product must be authorized by the respective CBs that own these marks. ote: - The above label is a representative label, the label for another model is identical to it except for model name. - The CE marking and WEEE symbol (if any) should be at least 5.0mm and 7.0mm respectively in height. - Manufacturers shall ensure that the equipment bears a type, batch or serial number or other element allowing its identification. - Manufacturers shall indicate on the electrical equipment their name, registered trade name or registered trade mark and the postal address at which they can be contacted. - Importers shall indicate on the electrical equipment their name, registered trade name or registered trade mark and the postal address at which they can be contacted. age 2 of 66

3 Report o.: R2XM A1-03 Test item particulars... : Equipment mobility...: movable hand-held transportable stationary for building-in direct plug-in Connection to the mains... : pluggable equipment type A type B detachable power supply cord non-detachable power supply cord not directly connected to the mains permanent connection Operating condition... : continuous rated operating / resting time: Access location... : operator accessible restricted access location Over voltage category (OVC)... : OVC I OVC II OVC III OVC IV Mains supply tolerance (%)... : /A Tested for IT power systems... : Yes o IT testing, phase-phase voltage (V)... : /A other: ot directly connected to the mains Class of equipment... : Class I Class II Class III Considered current rating of protective device as part of the building installlation (A)... : /A ot classified ollution degree (D)... : D 1 D 2 D 3 I protection class... : IX0 Altitude during operation (m)... : Up to 2000m Altitude of test laboratory (m)... : Below 2000m Max. Specified ambient temperature( C)... : 60 C Mass of equipment (kg)... : Approx kg ossible test case verdicts... : - test case does not apply to the test object... : /A(or ) - test object does meet the requirement... : (ass) - test object does not meet the requirement... : F(ail) General remarks: (see remark #) refers to a remark appended to the report. (see appended table) refers to a table appended to the report. The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the testing laboratory. Throughout this report a comma/ point is used as the decimal separator. age 3 of 66

4 Report o.: R2XM A1-03 Summary of testing: All tests were performed on model XT-10 at the worst case and all test results complied with the standard on the cover page. General product information: 1. The product is a I Video Intercom designed as information technology equipment. 2. The product is powered by SELV, LS circuit of 12VDC or OE port. 3. The communication network circuit was considered as TV-2 circuit. 4. Before placing the products in the different countries, the manufacturer must ensure that: Operating Instructions, Ratings Labels and Warnings Labels are in an Accepted or Official Language of the country in question; The equipment complies with the ational Standards and/or Electrical Codes of the country, province or city or in question. Remark: This reprot is based on the BACL report o.: R2XM , the different as below: 1. The applicant's and manufacture's name is changed to United GULF GATE Co.; address is changed to " Aladel Tower, F21, Fahad Al Salem St., State of KUWAIT ". 2. The model is changed to: XT-10; 3. The product name is changed to: I Video Intercom, The trademark updated to: Xontel. 4. The changes between the original device and the current one are stated and guaranteed by the applicant, the differences between them will not affect the test results. We will keep the results, test photos but update the related EUT photos. 5. For the appearance, changed the silk-screen of trade name and the label. Except the differences above, the products are electrically identical. age 4 of 66

5 Report o.: R2XM A1-03 E GEERAL 1.5 Components General Comply with IEC or relevant component standard (see appended tables 1.5.1) Evaluation and testing of components Certified components are used in accordance with their ratings, certifications and they comply with applicable parts of this Standard. Components not certified are used in accordance with their ratings and they comply with IEC and the relevant component Standard. Components, for which no relevant IEC Standard exist, have been tested under the condition occurring in the equipment, using applicable parts of IEC Thermal controls o such component Transformers (see appended table 1.5.1) Interconnecting cables Comply with the standard Capacitors bridging insulation o primary circuit Resistors bridging insulation o such component Resistors bridging functional, basic or supplementary insulation Resistors bridging double or reinforced insulation between a.c. mains and other circuits Resistors bridging double or reinforced insulation between a.c. mains and antenna or coaxial cable Components in equipment for IT power systems Surge suppressors o such component General rotection of VDRs Bridging of functional insulation by a VDR Bridging of basic insulation by a VDR Bridging of supplementary, double or reinforced insulation by a VDR age 5 of 66

6 Report o.: R2XM A1-03 E ower interface AC power distribution systems Class III equipment Input current (See appended table 1.6.2) Voltage limit of hand-held equipment ot a hand-held equipment eutral conductor Class III equipment. 1.7 Marking and instructions ower rating and identification markings See below ower rating marking ot directly connected to the mains Multiple mains supply connections...: Rated voltage(s) or voltage range(s) (V)... : Symbol for nature of supply, for d.c. only... : Rated frequency or rated frequency range (Hz)... : Rated current (ma or A)... : Identification markings See below. Manufacturer s name or trade-mark or identification mark... : See making plate Model identification or type reference... : See making plate Symbol for Class II equipment only... : Class III equipment. Other markings and symbols... : Others marking can be added, which not misunderstand Use of graphical symbols Safety instructions and marking The user s manual contains information for operation, installation, servicing, transport, storage and technical data General Considered Disconnect devices o such device Overcurrent protective device o such device IT power distribution systems Operator access with a tool Ozone The equipment does not produce ozone Short duty cycles Continuous operation Supply voltage adjustment... : o such component age 6 of 66

7 Report o.: R2XM A1-03 E Methods and means of adjustment; reference to installation instructions... : ower outlets on the equipment... : o standard power outlet Fuse identification (marking, special fusing characteristics, cross-reference)... : o such component Wiring terminals o such wiring terminals rotective earthing and bonding terminals... : o such terminals Terminals for a.c. mains supply conductors o connection to a.c. mains supply Terminals for d.c. mains supply conductors o connection to d.c. mains supply Controls and indicators Identification, location and marking... : Colours... : o indicators with colours where safety is involved Symbols according to IEC : Markings using figures... : Isolation of multiple power sources... : Thermostats and other regulating devices... : o thermostats or other regulating devices Durability Rubbed with a cloth soaked with water for 15s then again for 15s with cloth soaked with petroleum spirit, after this test, the marking on the label did not fade there are no curling nor lifting of the label edge Removable parts Replaceable batteries... : Language(s)... : Equipment for restricted access locations... : 2 ROTECTIO FROM HAZARDS 2.1 rotection from electric shock and energy hazards rotection in operator access areas Only SELV circuits are accessible by operator Access to energized parts See below Test by inspection... : Test with test finger (Figure 2A)... : age 7 of 66 rotection established by enclosure o hazards parts can be accessible

8 Report o.: R2XM A1-03 E Test with test pin (Figure 2B)... : Test with test probe (Figure 2C)... : o hazards parts can be accessible o hazards parts can be accessible Battery compartments o such component Access to ELV wiring o ELV wiring Working voltage (Vpeak or Vrms); minimum distance through insulation (mm) Access to hazardous voltage circuit wiring o hazardous voltage circuit wiring Energy hazards... : o energy hazard Manual controls o such device Discharge of capacitors in equipment o such component Measured voltage (V); time-constant (s)... : Energy hazards d.c. mains supply o connection to d.c. mains supply a) Capacitor connected to the d.c. mains supply.. : b) Internal battery connected to the d.c. mains supply... : Audio amplifiers... : Considered rotection in service access areas rotection in restricted access locations 2.2 SELV circuits General requirements Class III equipment Voltages under normal conditions (V)... : 42.4V peak or 60V d.c. are not exceeded in SELV circuits Voltages under fault conditions (V)... : ot exceed 42.4V peak or 60V d.c. for longer than 0.2s, and under limit of 71V peak or 120V d.c. within 0.2s Connection of SELV circuits to other circuits... : Only intended to be connected with SELV circuits. 2.3 TV circuits Limits The Max. U dc under normal operating conditions: 120V; The Max. U dc in the event of a single fault: 120V Type of TV circuits... : TV-2 circuit age 8 of 66

9 Report o.: R2XM A1-03 E Separation from other circuits and from accessible parts See below General requirements Complied rotection by basic insulation rotection by earthing rotection by other constructions... : By simulation of failures of components and insulation, see appended table Separation from hazardous voltages Insulation employed... : Connection of TV circuits to other circuits o primary circuit, only connection with SELV circuits Insulation employed... : Test for operating voltages generated externally 2.4 Limited current circuits General requirements o limited current circuits Limit values Frequency (Hz)... : Measured current (ma)... : Measured voltage (V)... : Measured circuit capacitance (nf or µf)... : Connection of limited current circuits to other circuits 2.5 Limited power sources a) Inherently limited output b) Impedance limited output c) Regulating network or IC current limiter, limits output under normal operating and single fault condition Use of integrated circuit (IC) current limiters d) Overcurrent protective device limited output Max. output voltage (V), max. output current (A), max. apparent power (VA)... : Current rating of overcurrent protective device (A).: 2.6 rovisions for earthing and bonding rotective earthing Class III equipment age 9 of 66

10 E Report o.: R2XM A Functional earthing Use of symbol for functional earthing...: rotective earthing and protective bonding conductors General Size of protective earthing conductors Rated current (A), cross-sectional area (mm 2 ), AWG... : Size of protective bonding conductors Rated current (A), cross-sectional area (mm 2 ), AWG... : rotective current rating (A), cross-sectional area (mm 2 ), AWG... : Resistance of earthing conductors and their terminations; resistance (Ω), voltage drop (V), test current (A), duration (min)... : Colour of insulation... : Terminals General rotective earthing and bonding terminals Rated current (A), type, nominal thread diameter (mm)... : Separation of the protective earthing conductor from protective bonding conductors Integrity of protective earthing Interconnection of equipment Components in protective earthing conductors and protective bonding conductors Disconnection of protective earth arts that can be removed by an operator arts removed during servicing Corrosion resistance Screws for protective bonding Reliance on telecommunication network or cable distribution system 2.7 Overcurrent and earth fault protection in primary circuits Basic requirements Class III equipment Instructions when protection relies on building installation age 10 of 66

11 Report o.: R2XM A1-03 E Faults not simulated in Short-circuit backup protection umber and location of protective devices...: rotection by several devices Warning to service personnel...: 2.8 Safety interlocks General principles o safety interlocks rotection requirements Inadvertent reactivation Fail-safe operation rotection against extreme hazard Moving parts Overriding Switches, relays and their related circuits Separation distances for contact gaps and their related circuits (mm)... : Overload test Endurance test Electric strength test Mechanical actuators 2.9 Electrical insulation roperties of insulating materials atural rubber, hygroscopic and materials containing asbestos not used as insulation Humidity conditioning 120 hours Relative humidity (%), temperature ( C)... : 93%, 40 C Grade of insulation Functional, basic insulation Separation from hazardous voltages Method(s) used... : 2.10 Clearances, creepage distances and distances through insulation General See below Frequency...: <30kHz ollution degrees...: ollution degree Reduced values for functional insualtion age 11 of 66

12 Report o.: R2XM A1-03 E Intervening unconnected conductive parts Insulation with varying dimensions Special separation requirements Insulation in circuits generating starting pulses Determination of working voltage (see appended table ) General Considered RMS working voltage eak working voltage Clearances See below General Considered Mains transient voltages a) AC mains supply...: b) Earthed d.c. mains supplies...: c) Unearthed d.c. mains supplies...: d) Battery operation...: Clearances in primary circuits Clearances in secondary circuits (See appended table and ) Clearances in circuits having starting pulses Transients from a.c. mains supply... : Transients from d.c. mains supply... : Transients from telecommunication networks and cable distribution systems... : TV-2 circuit, 800Vp Measurement of transient voltage levels a) Transients from a mains supply For an a.c. mains supply... : For a d.c. mains supply... : b) Transients from a telecommunication network : Creepage distances See below General Considered Material group and caomparative tracking index See below CTI tests... : age 12 of 66 Material group IIIb is assumed to be used Minimum creepage distances (see appended table and ) Solid insulation General

13 E Report o.: R2XM A Distances through insulation Only functional and basic insulation Insulating compound as solid insulation Semiconductor devices Cemented joints Thin sheet material General Separable thin sheet material umber of layers (pcs)... : on-separable thin sheet material Thin sheet material standard test procedure Electric strength test Thin sheet material alternative test procedure Electric strength test Insulation in wound components Only functional insulation Wire in wound components Working voltage... : a) Basic insulation not under stress... : b) Basic, supplemetary, reinforced insulation... : c) Compliance with Annex U... : Two wires in contact inside wound component; angle between 45 and : Wire with solvent-based enamel in wound components Electric strength test Routine test Additional insulation in wound components Working voltage... : - Basic insulation not under stress... : - Supplemetary, reinforced insulation... : Construction of printed boards See below Uncoated printed boards Complied Coated printed boards Insulation between conductors on the same inner surface of a printed board Insulation between conductors on different layers of a printed board Distance through insulation age 13 of 66

14 E Report o.: R2XM A1-03 umber of insulation layers (pcs)... : Component external terminations Tests on coated printed boards and coated components Sample preparation and preliminary inspection Thermal conditioning Electric strength test Abrasion resistance test Thermal cycling Test for ollution Degree 1 environment and insulating compound Tests for semiconductor devices and cemented joints Enclosed and sealed parts 3 WIRIG, COECTIOS AD SULY 3.1 General Current rating and overcurrent protection The cross-sectional area of internal wires and interconnecting cables shall be adequate for the current they are intended to carry when the equipment is operating under normal load such that the maximum permitted temperature of conductor insulation is not exceeded rotection against mechanical damage Wireways are smooth and free from sharp edges Securing of internal wiring Insulation of conductors Beads and ceramic insulators Screws for electrical contact pressure o such screws Insulating materials in electrical connections Self-tapping and spaced thread screws o such screws Termination of conductors 10 pull test Sleeving on wiring o sleeving 3.2 Connection to a mains supply age 14 of 66

15 E Report o.: R2XM A Means of connection Class III equipment Connection to an a.c. mains supply Connection to a d.c. mains supply Multiple supply connections ermanently connected equipment umber of conductors, diameter of cable and conduits (mm)... : Appliance inlets ower supply cords AC power supply cords Type... : Rated current (A), cross-sectional area (mm 2 ), AWG... : DC power supply cords Cord anchorages and strain relief Mass of equipment (kg), pull ()... : Longitudinal displacement (mm)... : rotection against mechanical damage Cord guards Diameter or minor dimension D (mm); test mass (g)... : Radius of curvature of cord (mm)... : Supply wiring space 3.3 Wiring terminals for connection of external conductors Wiring terminals o wiring terminals Connection of non-detachable power supply cords Screw terminals Conductor sizes to be connected Rated current (A), cord/cable type, cross-sectional area (mm 2 )... : Wiring terminal sizes Rated current (A), type, nominal thread diameter (mm)... : Wiring terminal design Grouping of wiring terminals Stranded wire age 15 of 66

16 E Report o.: R2XM A Disconnection from the mains supply General requirement Class III equipment Disconnect devices ermanently connected equipment arts which remain energized Switches in flexible cords umber of poles - single-phase and d.c. equipment umber of poles - three-phase equipment Switches as disconnect devices lugs as disconnect devices Interconnected equipment Multiple power sources 3.5 Interconnection of equipment General requirements Considered Types of interconnection circuits... : SELV circuits ELV circuits as interconnection circuits o ELV circuits Data ports for additional equipment 4 HYSICAL REQUIREMETS 4.1 Stability Angle of 10 Mass < 7kg Test force ()... : 4.2 Mechanical strength General See below Rack-mounted equipment. ot rack-mounted equipment Steady force test, 10 For internal components, after test, no hazards Steady force test, Steady force test, 250 For external enclosure, after test, no hazards Impact test 500g, 1.3m, no hazard. Fall test Top side of enclosure Swing test age 16 of 66 Three vertical side of enclosure

17 E Report o.: R2XM A Drop test; height (mm)... : Stress relief test 83 C, for 7hours, no hazard Cathode ray tubes o such tubes icture tube separately certified... : High pressure lamps o such lamps Wall or ceiling mounted equipment; force ()... : 50, no damaged, no hazard 4.3 Design and construction Edges and corners All coners are smooth and rounded Handles and manual controls; force ()... : o such device Adjustable controls o adjustable controls Securing of parts Connection by plugs and sockets Direct plug-in equipment Torque... : Compliance with the relevant mains plug standard... : Heating elements in earthed equipment o such component Batteries - Overcharging of a rechargeable battery - Unintentional charging of a non-rechargeable battery - Reverse charging of a rechargeable battery - Excessive discharging rate for any battery Oil and grease o oil and grease Dust, powders, liquids and gases Containers for liquids or gases Flammable liquids... : Quantity of liquid (l)... : Flash point ( C)... : Radiation See below General See below Ionizing radiation Measured radiation (pa/kg)... : Measured high-voltage (kv)... : Measured focus voltage (kv)... : age 17 of 66

18 E Report o.: R2XM A1-03 CRT markings... : Effect of ultraviolet (UV) radiation on materials art, property, retention after test, flammability classification... : Human exposure to ultraviolet (UV) radiation... : Lasers (including laser diodes) and LEDs LED only used as indicator Lasers (including laser diodes) Laser class... : Light emitting diodes (LEDs) LED only used as indicator Other types... : 4.4 rotection against hazardous moving parts General o moving parts rotection in operator access areas... : Household and home/office document/media shredders rotection in restricted access locations... : rotection in service access areas rotection against moving fan blades General ot considered to cause pain or injury. a).: Is considered to cause pain, not injury. b) : Considered to cause injury. c) : rotection for users Use of symbol or warning : rotection for service persons Use of symbol or warning : 4.5 Thermal requirements General See below Temperature tests (see appended table 4.5) ormal load condition per Annex L... : Temperature limits for materials (see appended table 4.5) Touch temperature limits (see appended table 4.5) Resistance to abnormal heat... : 4.6 Openings in enclosures age 18 of 66

19 Report o.: R2XM A1-03 E Top and side openings o fire enclosure needed Dimensions (mm)... : Bottoms of fire enclosures Construction of the bottomm, dimensions (mm).. : Doors or covers in fire enclosures Openings in transportable equipment Constructional design measures Dimensions (mm)... : Evaluation measures for larger openings Use of metallized parts Adhesives for constructional purposes Conditioning temperature ( C), time (weeks)... : 4.7 Resistance to fire Reducing the risk of ignition and spread of flame Method 1 used. See below. Method 1, selection and application of components wiring and materials Method 2, application of all of simulated fault condition tests Materials with the required flammability classes are used-see appended table Conditions for a fire enclosure See below arts requiring a fire enclosure arts not requiring a fire enclosure SECODARY CIRCUITS supplied by limited power sources complying with 2.5 and mounted on V-1 CLASS MATERIAL Materials General See below Materials for fire enclosures (see appended table 1.5.1) Materials for components and other parts outside fire enclosures Materials for components and other parts inside fire enclosures (see appended table 1.5.1) Materials for air filter assemblies o air filters in the equipment Materials used in high-voltage components o parts exceeding 4kV. 5 ELECTRICAL REQUIREMETS AD SIMULATED ABORMAL CODITIOS 5.1 Touch current and protective conductor current age 19 of 66

20 E Report o.: R2XM A General Class III equipment Configuration of equipment under test (EUT) Single connection to an a.c. mains supply Redundant multiple connections to an a.c. mains supply Simultaneous multiple connections to an a.c. mains supply Test circuit Application of measuring instrument Test procedure Test measurements Supply voltage (V)... : Measured touch current (ma)... : Max. allowed touch current (ma)... : Measured protective conductor current (ma)... : Max. allowed protective conductor current (ma).. : Equipment with touch current exceeding 3,5 ma General... : Simultaneous multiple connections to the supply Touch currents to telecommunication networks and cable distribution systems and from telecommunication networks Limitation of the touch current to a telecommunication network or to a cable distribution system Supply voltage (V)... : Measured touch current (ma)... : Max. allowed touch current (ma)... : Summation of touch currents from telecommunication networks a) EUT with earthed telecommunication ports... : b) EUT whose telecommunication ports have no reference to protective earth 5.2 Electric strength General Test procedure (see appended table 5.2) age 20 of 66

21 E Report o.: R2XM A Abnormal operating and fault conditions rotection against overload and abnormal operation (See appended table 5.3) Motors Transformers (See appended table 5.3) Functional insulation... : Complies with c) Electromechanical components o such component Audio amplifiers in ITE... : Considered Simulation of faults (see appended table 5.3) Unattended equipment Compliance criteria for abnormal operating and fault conditions (see appended table 5.3) During the tests o hazard After the tests o hazard. 6 COECTIO TO TELECOMMUICATIO ETWORKS 6.1 rotection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment rotection from hazardous voltages Separation of the telecommunication network from earth Requirements Supply voltage (V)... : Current in the test circuit (ma)... : Exclusions... : 6.2 rotection of equipment users from overvoltages on telecommunication networks Separation requirements Electric strength test procedure Impulse test Steady-state test Compliance criteria 6.3 rotection of the telecommunication wiring system from overheating Max. output current (A)... : Current limiting method... : age 21 of 66

22 Report o.: R2XM A1-03 E COECTIO TO CABLE DISTRIBUTIO SYSTEMS 7.1 General o connected to cable distribution system. 7.2 rotection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment 7.3 rotection of equipment users from overvoltages on the cable distribution system 7.4 Insulation between primary circuits and cable distribution systems General Voltage surge test Impulse test A AEX A, TESTS FOR RESISTACE TO HEAT AD FIRE A.1 Flammability test for fire enclosures of movable equipment having a total mass exceeding 18 kg, and of stationary equipment (see ) A.1.1 Samples... : Wall thickness (mm)... : A.1.2 Conditioning of samples; temperature ( C)... : A.1.3 Mounting of samples... : A.1.4 Test flame (see IEC ) Flame A, B, C or D... : A.1.5 Test procedure A.1.6 Compliance criteria Sample 1 burning time (s)... : Sample 2 burning time (s)... : Sample 3 burning time (s)... : A.2 Flammability test for fire enclosures of movable equipment having a total mass not exceeding 18 kg, and for material and components located inside fire enclosures (see and ) A.2.1 Samples, material... : Wall thickness (mm)... : A.2.2 Conditioning of samples; temperature ( C)... : A.2.3 Mounting of samples... : A.2.4 Test flame (see IEC ) Flame A, B or C... : age 22 of 66

23 E Report o.: R2XM A1-03 A.2.5 Test procedure A.2.6 Compliance criteria Sample 1 burning time (s)... : Sample 2 burning time (s)... : Sample 3 burning time (s)... : A.2.7 Alternative test acc. to IEC , cl. 5 and 9 Sample 1 burning time (s)... : Sample 2 burning time (s)... : Sample 3 burning time (s)... : A.3 Hot flaming oil test (see 4.6.2) A.3.1 Mounting of samples A.3.2 Test procedure A.3.3 Compliance criterion B AEX B, MOTOR TESTS UDER ABORMAL CODITIOS (see and 5.3.2) B.1 General requirements osition... : Manufacturer... : Type... : Rated values... : B.2 Test conditions B.3 Maximum temperatures B.4 Running overload test B.5 Locked-rotor overload test Test duration (days)... : Electric strength test: test voltage (V)... : B.6 Running overload test for d.c. motors in secondary circuits B.6.1 General B.6.2 Test procedure B.6.3 Alternative test procedure B.6.4 Electric strength test; test voltage (V)... : B.7 Locked-rotor overload test for d.c. motors in secondary circuits B.7.1 General age 23 of 66

24 E Report o.: R2XM A1-03 B.7.2 Test procedure B.7.3 Alternative test procedure B.7.4 Electric strength test; test voltage (V)...: B.8 Test for motors with capacitors B.9 Test for three-phase motors B.10 Test for series motors Operating voltage (V)... : C AEX C, TRASFORMERS (see and 5.3.3) osition... : Manufacturer... : Type... : Rated values... : Method of protection... : C.1 Overload test C.2 Insulation rotection from displacement of windings... : D AEX D, MEASURIG ISTRUMETS FOR TOUCH-CURRET TESTS (see 5.1.4) D.1 Measuring instrument D.2 Alternative measuring instrument E AEX E, TEMERATURE RISE OF A WIDIG (see ) F AEX F, MEASUREMET OF CLEARACES AD CREEAGE DISTACES (see 2.10 and Annex G) G AEX G, ALTERATIVE METHOD FOR DETERMIIG MIIMUM CLEARACES G.1 Clearances G.1.1 General G.1.2 Summary of the procedure for determining minimum clearances G.2 Determination of mains transient voltage (V) G.2.1 AC mains supply... : G.2.2 Earthed d.c. mains supplies... : age 24 of 66

25 E Report o.: R2XM A1-03 G.2.3 Unearthed d.c. mains supplies... : G.2.4 Battery operation... : G.3 Determination of telecommunication network transient voltage (V)... : G.4 Determination of required withstand voltage (V) G.4.1 Mains transients and internal repetitive peaks... : G.4.2 Transients from telecommunication networks... : G.4.3 Combination of transients G.4.4 Transients from cable distribution systems G.5 Measurement of transient voltages (V) a) Transients from a mains supply For an a.c. mains supply For a d.c. mains supply b) Transients from a telecommunication network G.6 Determination of minimum clearances... : H AEX H, IOIZIG RADIATIO (see ) J AEX J, TABLE OF ELECTROCHEMICAL OTETIALS (see ) Metal(s) used... : K AEX K, THERMAL COTROLS (see and 5.3.8) K.1 Making and breaking capacity K.2 Thermostat reliability; operating voltage (V)... : K.3 Thermostat endurance test; operating voltage (V)... : K.4 Temperature limiter endurance; operating voltage (V)... : K.5 Thermal cut-out reliability K.6 Stability of operation L AEX L, ORMAL LOAD CODITIOS FOR SOME TYES OF ELECTRICAL BUSIESS EQUIMET (see and 4.5.2) L.1 Typewriters L.2 Adding machines and cash registers L.3 Erasers L.4 encil sharpeners age 25 of 66

26 E Report o.: R2XM A1-03 L.5 Duplicators and copy machines L.6 Motor-operated files L.7 Other business equipment (See appended table 1.6.2) M AEX M, CRITERIA FOR TELEHOE RIGIG SIGALS (see 2.3.1) M.1 Introduction M.2 Method A M.3 Method B M.3.1 Ringing signal M Frequency (Hz)... : M Voltage (V)... : M Cadence; time (s), voltage (V)... : M Single fault current (ma)... : M.3.2 Tripping device and monitoring voltage... : M Conditions for use of a tripping device or a monitoring voltage M Tripping device M Monitoring voltage (V)... : AEX, IMULSE TEST GEERATORS (see , , , , 7.3.2, and Clause G.5).1 ITU-T impulse test generators.2 IEC impulse test generator AEX, ORMATIVE REFERECES Q AEX Q, Voltage dependent resistors (VDRs) (see ) - referred climatic categories... : - Maximum continuous voltage... : - Combination pulse current... : Body of the VDR Test according to IEC : Body of the VDR. Flammability class of material ( min V-1)...: R AEX R, EXAMLES OF REQUIREMETS FOR QUALITY COTROL ROGRAMMES age 26 of 66

27 E Report o.: R2XM A1-03 R.1 Minimum separation distances for unpopulated coated printed boards (see ) R.2 Reduced clearances (see ) S AEX S, ROCEDURE FOR IMULSE TESTIG (see ) S.1 Test equipment S.2 Test procedure S.3 Examples of waveforms during impulse testing T AEX T, GUIDACE O ROTECTIO AGAIST IGRESS OF WATER (see 1.1.2) U AEX U, ISULATED WIDIG WIRES FOR USE WITHOUT ITERLEAVED ISULATIO (see ) V AEX V, AC OWER DISTRIBUTIO SYSTEMS (see 1.6.1) V.1 Introduction V.2 T power distribution systems W AEX W, SUMMATIO OF TOUCH CURRETS W.1 Touch current from electronic circuits W.1.1 Floating circuits W.1.2 Earthed circuits W.2 Interconnection of several equipments W.2.1 Isolation W.2.2 Common return, isolated from earth W.2.3 Common return, connected to protective earth X AEX X, MAXIMUM HEATIG EFFECT I TRASFORMER TESTS (see clause C.1) X.1 Determination of maximum input current X.2 Overload test procedure Y AEX Y, ULTRAVIOLET LIGHT CODITIOIG TEST (see ) Y.1 Test apparatus... : Y.2 Mounting of test samples... : age 27 of 66

28 E Report o.: R2XM A1-03 Y.3 Carbon-arc light-exposure apparatus... : Y.4 Xenon-arc light exposure apparatus... : Z AEX Z, OVERVOLTAGE CATEGORIES (see and Clause G.2) AA AEX AA, MADREL TEST (see ) BB AEX BB, CHAGES I THE SECOD EDITIO CC AEX CC, Evaluation of integrated circuit (IC) current limiters CC.1 General CC.2 Test program 1.: CC.3 Test program 2.: CC.4 Test program 3...: CC.5 Compliance...: DD AEX DD, Requirements for the mounting means of rack-mounted equipment DD.1 General DD.2 Mechanical strength test, variable.....: DD.3 Mechanical strength test, 250, including end stops : DD.4 Compliance...: EE AEX EE, Household and home/office document/media shredders EE.1 General EE.2 Markings and instructions Use of markings or symbols : Information of user instructions, maintenance and/or servicing instructions : EE.3 Inadvertent reactivation test : EE.4 Disconnection of power to hazardous moving parts: Use of markings or symbols : EE.5 rotection against hazardous moving parts Test with test finger (Figure 2A) : Test with wedge probe (Figure EE1 and EE2) : age 28 of 66

29 E Report o.: R2XM A1-03 Group differences COMMO MODIFICATIOS for E :2006+A11:2009+A1:2010+A12:2011+A2:2013 Contents Contents (A2:2013) Whole document (A2:2013) General General (A1:2010) (A1:2010) Add the following annexes: Annex ZA (normative) ormative references to international publications with their corresponding European publications Annex ZB (normative) Special national conditions Annex ZC (informative) A-deviations Add the following: Annex ZD (informative) IEC and CEELEC code designations for flexible cords Delete all the country notes in the reference document according to the following list: ote * ote ote * ote of secretary: Text of Common Modification remains unchanged For special national conditions, see Annex ZB. Delete all the country notes in the reference document according to the following list: ote ote 2 & ote ote ote ote 4, 5 & ote ote ote ote ote ote 2 & ote ote ote ote ote ote ote 1 & ote ote ote ote 3 & ote 1 6 ote 2 & ote ote ote ote ote 7.1 ote ote 7.3 ote 1 & 2 G.2.1 ote 2 Annex H ote 2 In IEC :2005/A1 delete all the country notes according to the following list: : ote : ote : ote 2 - EE.3: ote Replace the text of OTE 3 by the following OTE 3 The requirements of E may also be used to meet safety requirements for multimedia equipment. See IEC Guide 112, Guide on the safety of multimedia equipment. For television sets E applies. age 29 of 66

30 E Report o.: R2XM A (A1:2010) 1.3.Z1 Add the following definition: Z1 ORTABLE SOUD SYSTEM small battery powered audio equipment: whose prime purpose is to listen to recorded or broadcasted sound; and that uses headphones or earphones that can be worn in or on or around the ears; and that allows the user to walk around OTE Examples are mini-disk or CD players; M3 audio players or similar equipment. Add the following subclause: 1.3.Z1 Exposure to excessive sound pressure The apparatus shall be so designed and constructed as to present no danger when used for its intended purpose, either in normal operating conditions or under fault conditions, particularly providing protection against exposure to excessive sound pressures from headphones or earphones. OTE Z1 A new method of measurement is described in E , Sound system equipment: Headphones and earphones associated with portable audio equipment - Maximum sound pressure level measurement methodology and limit considerations - art 1: General method for one package equipment, and in E , Sound system equipment: Headphones and earphones associated with portable audio equipment - Maximum sound pressure level measurement methodology and limit considerations - art 2: Guidelines to associate sets with headphones coming from different manufacturers Add the following OTE: OTE Z1 The use of certain substances in electrical and electronic equipment is restricted within the EU: see Directive 2002/95/EC Add the following OTE: OTE Z1 In addition, the instructions shall include, as far as applicable, a warning that excessive sound pressure from earphones and headphones can cause hearing loss age 30 of 66

31 E Report o.: R2XM A (A1:2010) Delete OTE Z1. Add the following paragraph at the end of the subclause: In addition, for a ORTABLE SOUD SYSTEM, the instructions shall include a warning that excessive sound pressure from earphones and headphones can cause hearing loss Replace the subclause as follows: Basic requirements To protect against excessive current, short-circuits and earth faults in RIMARY CIRCUITS, protective devices shall be included either as integral parts of the equipment or as parts of the building installation, subject to the following, a), b) and c): a) except as detailed in b) and c), protective devices necessary to comply with the requirements of 5.3 shall be included as parts of the equipment; b) for components in series with the mains input to the equipment such as the supply cord, appliance coupler, r.f.i. filter and switch, short-circuit and earth fault protection may be provided by protective devices in the building installation; c) it is permitted for LUGGABLE EQUIMET TYE B or ERMAETLY COECTED EQUIMET, to rely on dedicated overcurrent and short-circuit protection in the building installation, provided that the means of protection, e.g. fuses or circuit breakers, is fully specified in the installation instructions. If reliance is placed on protection in the building installation, the installation instructions shall so state, except that for LUGGABLE EQUIMET TYE A the building installation shall be regarded as providing protection in accordance with the rating of the wall socket outlet This subclause has been declared void Delete the OTE in Table 3A, and delete also in this table the conduit sizes in parentheses. age 31 of 66

32 E Report o.: R2XM A Replace IEC 53 by H05 RR-F ; IEC 52 by H03 VV-F or H03 VVH2-F ; IEC 53 by H05 VV-F or H05 VVH2-F2. In Table 3B, replace the first four lines by the following: Up to and including 6 0,75 a) Over 6 up to and including 10 (0,75) b) 1,0 Over 10 up to and including 16 (1,0) c) 1,5 In the conditions applicable to Table 3B delete the words in some countries in condition a). In OTE 1, applicable to Table 3B, delete the second sentence (A2:2013) Add the following ote: OTE Z1 The harmonised code designations corresponding to the IEC cord types are given in Annex ZD In Table 3D, delete the fourth line: conductor sizes for 10 to 13 A, and replace with the following: Over 10 up to and including 16 1,5 to 2,5 1,5 to 4 Delete the fifth line: conductor sizes for 13 to 16 A Add the following OTE: OTE Z1 Attention is drawn to 1999/519/EC: Council Recommendation on the limitation of exposure of the general public to electromagnetic fields 0 Hz to 300 GHz. Standards taking into account this Recommendation which demonstrate compliance with the applicable EU Directive are indicated in the OJEC (A1:2010) Replace the existing OTE by the following: OTE Z1 Attention is drawn to : 1999/519/EC: Council Recommendation on the limitation of exposure of the general public to electromagnetic fields 0 Hz to 300 GHz, and 2006/25/EC: Directive on the minimum health and safety requirements regarding the exposure of workers to risks arising from physical agents (artificial optical radiation). Standards taking into account mentioned Recommendation and Directive which demonstrate compliance with the applicable EU Directive are indicated in the OJEC. age 32 of 66

33 E Report o.: R2XM A1-03 Annex H Bibliography Replace the last paragraph of this annex by: At any point 10 cm from the surface of the OERATOR ACCESS AREA, the dose rate shall not exceed 1 μsv/h (0,1 mr/h) (see OTE). Account is taken of the background level. Replace the notes as follows: OTE These values appear in Directive 96/29/Euratom. Delete OTE 2. Add the following standards: E :2000, Sound system equipment: Headphones and earphones associated with portable audio equipment - Maximum sound pressure level measurement methodology and limit considerations - art 1: General method for one package equipment E :2003, Sound system equipment: Headphones and earphones associated with portable audio equipment - Maximum sound pressure level measurement methodology and limit considerations - art 2: Matching of sets with headphones if either or both are offered separately Add the following notes for the standards indicated: IEC OTE Harmonized in E series (not modified). IEC OTE Harmonized as HD :2005 (modified). IEC OTE Harmonized as HD S2:1996 (modified). IEC OTE Harmonized as E 60529:1991 (not modified). IEC OTE Harmonized as E :2006 (not modified). IEC OTE Harmonized as E :2005 (modified). IEC OTE Harmonized as E :2004 (not modified). IEC OTE Harmonized as E :2004 (not modified). IEC OTE Harmonized as E 61032:1998 (not modified). age 33 of 66

34 Report o.: R2XM A1-03 E Bibliography (A1:2010) IEC OTE Harmonized as E 61140:2002 (not modified). IEC OTE Harmonized as E :2005 (not modified). IEC OTE Harmonized as E :2001 (not modified). IEC OTE Harmonized as E :2001 (not modified). IEC OTE Harmonized as E :2002 (not modified). IEC OTE Harmonized as E :2003 (not modified). IEC OTE Harmonized as E 61965:2003 (not modified). ISO 4892 OTE Harmonized in E ISO 4892 series (not modified). Add the following note for the standard indicated: IEC OTE Harmonized as E ZA (A2:2013) ormative references to international publications with their corresponding European publications ZB Special national conditions Special national condition: ational characteristic or practice that cannot be changed even over a long period, e.g. climatic conditions, electrical earthing conditions. OTE If it affects harmonization, it forms part of the European Standard. For the countries in which the relevant special national conditions apply these provisions are normative, for other countries they are informative In Denmark, certain types of Class I appliances (see ) may be provided with a plug not establishing earthing conditions when inserted into Danish socket-outlets (A11:2009) (A11:2009) Add as new SC: In orway and Sweden, for requirements see and 7.3 of this annex. Replace the existing SC by the following: In Finland, orway and Sweden, resistors bridging BASIC ISULATIO in CLASS I LUGGABLE EQUIMET TYE A must comply with the requirements in In addition when a single resistor is used, the resistor must withstand the resistor test in age 34 of 66

35 E Report o.: R2XM A In orway, due to the IT power system used (see annex V, Figure V.7), capacitors are required to be rated for the applicable line-to-line voltage (230 V) In Finland, orway and Sweden, the third dashed sentence is applicable only to equipment as defined in of this annex (A2:2013) (A2:2013) In Denmark, Finland, orway and Sweden, CLASS I LUGGABLE EQUIMET TYE A intended for connection to other equipment or a network shall, if safety relies on connection to protective earth or if surge suppressors are connected between the network terminals and accessible parts, have a marking stating that the equipment must be connected to an earthed mains socket-outlet. The marking text in the applicable countries shall be as follows: In Denmark: Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord. In Finland: "Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan" In orway: Apparatet må tilkoples jordet stikkontakt In Sweden: Apparaten skall anslutas till jordat uttag In Denmark, socket-outlets for providing power to other equipment shall be in accordance with the DS D1:2011. For class I equipment the following Standard Sheets are applicable: DK 1-3a, DK 1-1c, DK 1-1d, DK 1-5a or DK 1-7a, with the exception for STATIOARY EQUIMET where the socketoutlets shall be in accordance with Standard Sheet DK 1-1b, DK 1-1c, DK 1-1d or DK 1-5a. Socket outlets intended for providing power to Class II apparatus with a rated current of 2,5 A shall be in accordance with DS D1 standard sheet DKA 1-4a. Other current rating socket outlets shall be in compliance with by DS D1 Standard Sheet DKA 1-3a or DKA 1-3b. Justification the Heavy Current Regulations, 6c In orway, for requirements see , and of this annex. age 35 of 66

36 E Report o.: R2XM A In Finland, orway and Sweden there are additional requirements for the insulation. See and of this annex In orway, for requirements see , and of this annex In the United Kingdom, the current rating of the circuit shall be taken as 13 A, not 16 A In the United Kingdom, to protect against excessive currents and short-circuits in the RIMARY CIRCUIT of DIRECT LUG-I EQUIMET, tests according to 5.3 shall be conducted, using an external protective device rated 30 A or 32 A. If these tests fail, suitable protective devices shall be included as integral parts of the DIRECT LUG-I EQUIMET, so that the requirements of 5.3 are met In Finland, orway and Sweden, there are additional requirements for the insulation, see and of this annex In Switzerland, supply cords of equipment having a RATED CURRET not exceeding 10 A shall be provided with a plug complying with SEV 1011 or IEC and one of the following dimension sheets: SEV lug Type E 250/400 V, 10 A SEV lug Type 11 L+ 250 V, 10 A SEV lug Type 12 L++E 250 V, 10 A In general, E applies for plugs for currents exceeding 10 A. However, a 16 A plug and socketoutlet system is being introduced in Switzerland, the plugs of which are according to the following dimension sheets, published in February 1998: SEV lug Type 25 3L++E 230/400 V, 16 A SEV lug Type 21 L+ 250 V, 16 A SEV lug Type 23 L++E 250 V, 16 A age 36 of 66

37 E Report o.: R2XM A (A2:2013) In Denmark, supply cords of single-phase equipment having a rated current not exceeding 13 A shall be provided with a plug according to DS D1. CLASS I EQUIMET provided with socket-outlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules shall be provided with a plug in accordance with standard sheet DK 2-1a or DK 2-5a. If a single-phase equipment having a RATED CURRET exceeding 13 A or if a poly-phase equipment is provided with a supply cord with a plug, this plug shall be in accordance with the standard sheets DK 6-1a in DS D1 or E Justification the Heavy Current Regulations, 6c In Spain, supply cords of single-phase equipment having a rated current not exceeding 10 A shall be provided with a plug according to UE 20315:1994. Supply cords of single-phase equipment having a rated current not exceeding 2,5 A shall be provided with a plug according to UE-E 50075:1993. CLASS I EQUIMET provided with socket-outlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules, shall be provided with a plug in accordance with standard UE 20315:1994. If poly-phase equipment is provided with a supply cord with a plug, this plug shall be in accordance with UE-E In the United Kingdom, apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to BS 1363 by means of that flexible cable or cord and plug, shall be fitted with a standard plug in accordance with Statutory Instrument 1768: The lugs and Sockets etc. (Safety) Regulations 1994, unless exempted by those regulations. OTE Standard plug is defined in SI 1768:1994 and essentially means an approved plug conforming to BS 1363 or an approved conversion plug. age 37 of 66

38 E Report o.: R2XM A In Ireland, apparatus which is fitted with a flexible cable or cord and is designed to be connected to a mains socket conforming to I.S. 411 by means of that flexible cable or cord and plug, shall be fitted with a 13 A plug in accordance with Statutory Instrument 525: ational Standards Authority of Ireland (section 28) (13 A lugs and Conversion Adaptors for Domestic Use) Regulations In Switzerland, for requirements see of this annex In the United Kingdom, a power supply cord with conductor of 1,25 mm 2 is allowed for equipment with a rated current over 10 A and up to and including 13 A In the United Kingdom, the range of conductor sizes of flexible cords to be accepted by terminals for equipment with a RATED CURRET of over 10 A up to and including 13 A is: 1,25 mm 2 to 1,5 mm 2 nominal cross-sectional area In the United Kingdom, the torque test is performed using a socket outlet complying with BS 1363 part 1:1995, including Amendment 1:1997 and Amendment 2:2003 and the plug part of DIRECT LUG-I EQUIMET shall be assessed to BS 1363: art 1, 12.1, 12.2, 12.3, 12.9, 12.11, 12.12, 12.13, and 12.17, except that the test of is performed at not less than 125 C. Where the metal earth pin is replaced by an Insulated Shutter Opening Device (ISOD), the requirements of clauses 22.2 and 23 also apply In Ireland, DIRECT LUG-I EQUIMET is known as plug similar devices. Such devices shall comply with Statutory Instrument 526: ational Standards Authority of Ireland (Section 28) (Electrical plugs, plug similar devices and sockets for domestic use) Regulations, age 38 of 66

39 E Report o.: R2XM A In Finland, orway and Sweden TOUCH CURRET measurement results exceeding 3,5 ma r.m.s. are permitted only for the following equipment: STATIOARY LUGGABLE EQUIMET TYE A that is intended to be used in a RESTRICTED ACCESS LOCATIO where equipotential bonding has been applied, for example, in a telecommunication centre; and has provision for a permanently connected ROTECTIVE EARTHIG CODUCTOR; and is provided with instructions for the installation of that conductor by a SERVICE ERSO; STATIOARY LUGGABLE EQUIMET TYE B; STATIOARY ERMAETLY COECTED EQUIMET. age 39 of 66

40 E Report o.: R2XM A (A1:2010) In Finland, orway and Sweden, add the following text between the first and second paragraph of the compliance clause: If this insulation is solid, including insulation forming part of a component, it shall at least consist of either - two layers of thin sheet material, each of which shall pass the electric strength test below, or - one layer having a distance through insulation of at least 0,4 mm, which shall pass the electric strength test below. Alternatively for components, there is no distance through insulation requirement for the insulation consisting of an insulating compound completely filling the casing, so that CLEARACES and CREEAGE DISTACES do not exist, if the component passes the electric strength test in accordance with the compliance clause below and in addition - passes the tests and inspection criteria of with an electric strength test of 1,5 kv multiplied by 1,6 (the electric strength test of shall be performed using 1,5 kv), and - is subject to ROUTIE TESTIG for electric strength during manufacturing, using a test voltage of 1,5 kv. It is permitted to bridge this insulation with an optocoupler complying with b). It is permitted to bridge this insulation with a capacitor complying with E :2005, subclass Y2. A capacitor classified Y3 according to E :2005, may bridge this insulation under the following conditions: - the insulation requirements are satisfied by having a capacitor classified Y3 as defined by E , which in addition to the Y3 testing, is tested with an impulse test of 2,5 kv defined in E :2006, ; - the additional testing shall be performed on all the test specimens as described in E ; - the impulse test of 2,5 kv is to be performed before the endurance test in E , in the sequence of tests as described in E age 40 of 66

41 E Report o.: R2XM A In Finland, orway and Sweden, the exclusions are applicable for ERMAETLY COECTED EQUIMET, LUGGABLE EQUIMET TYE B and equipment intended to be used in a RESTRICTED ACCESS LOCATIO where equipotential bonding has been applied, e.g. in a telecommunication centre, and which has provision for a permanently connected ROTECTIVE EARTHIG CODUCTOR and is provided with instructions for the installation of that conductor by a SERVICE ERSO. 7.2 In Finland, orway and Sweden, for requirements see and of this annex. The term TELECOMMUICATIO ETWORK in being replaced by the term CABLE DISTRIBUTIO SYSTEM. 7.3 (A11:2009) Delete the existing SC for orway and Sweden (based on OTE 1 of IEC : corr. 1). Add as new SC (based on future OTE 3 of IEC :200X): In orway and Sweden, for requirements see and of this annex. 7.3 In orway, for installation conditions see E :2005. ZC A-deviations A-deviation: ational deviation due to regulations, the alteration of which is for the time being outside the competence of the CEELEC national member. This European Standard falls under Directives RTTED (1999/5/EC) and LVD (2006/95/EC). OTE (from CE/CEELEC IR art 2:2002, 2.17) Where standards fall under EC Directives, it is the view of the Commission of the European Communities (OJ o C 59, ) that the effect of the decision of the Court of Justice in case 815/79 Cremonini/Vrankovich (European Court Reports 1980, p. 3583) is that compliance with A-deviations is no longer mandatory and that the free movement of products complying with such a standard should not be restricted except under the safeguard procedure provided for in the relevant Directive. A-deviations in an EFTA-country are valid instead of the relevant provisions of the European Standard in that country until they have been removed Switzerland (Ordinance on environmentally hazardous substances SR , Annex 1.7, Mercury - Annex 1.7 of SR applies for mercury.) Add the following: OTE In Switzerland, switches containing mercury such as thermostats, relays and level controllers are not allowed. age 41 of 66

42 E Report o.: R2XM A Germany (Gesetz über technische Arbeitsmittel und Verbraucherprodukte (Geräte- und roduktsicherheitsgesetz GSG) [Law on technical labour equipment and consumer products], of 6th January 2004, Section 2, Article 4, Clause (4), Item 2). If for the assurance of safety and health certain rules during use, amending or maintenance of a technical labour equipment or readymade consumer product are to be followed, a manual in German language has to be delivered when placing the product on the market. Of this requirement, rules for use even only by SERVICE ERSOS are not exempted Switzerland (Ordinance on chemical hazardous risk reduction SR , Annex 2.15 Batteries) Annex 2.15 of SR applies for batteries. (A12:2011) Zx. rotection against excessive sound pressure from personal music players age 42 of 66

43 E Report o.: R2XM A1-03 Zx.1 General This sub-clause specifies requirements for protection against excessive sound pressure from personal music players that are closely coupled to the ear. It also specifies requirements for earphones and headphones intended for use with personal music players. A personal music player is a portable equipment for personal use, that: - is designed to allow the user to listen to recorded or broadcast sound or video; and - primarily uses headphones or earphones that can be worn in or on or around the ears; and - allows the user to walk around while in use. OTE 1 Examples are hand-held or body-worn portable CD players, M3 audio players, mobile phones with M3 type features, DA$s or similar equipment. A personal music player and earphones or headphones intended to be used with personal music players shall comply with the requirements of this sub-clause. The requirements in this sub-clause are valid for music or video mode only. The requirements do not apply: - while the personal music player is connected to an external amplifier; or - while the headphones or earphones are not used. OTE 2 An external amplifier is an amplifier which is not part of the personal music player or the listening device, but which is intended to play the music as a standalone music player. The requirements do not apply to: - hearing aid equipment and professional equipment; OTE 3 rofessional equipment is equipment sold through special sales channels. All products sold through normal electronics stores are considered not to be professional equipment. age 43 of 66

44 E Report o.: R2XM A analogue personal music players (personal music players without any kind of digital processing of the sound signal) that are brought to the market before the end of 2015 OTE 4 This exemption has been allowed because this technology is falling out of use and it is expected that within a few years it will no longer exist. This exemption will not be extended to other technologies. For equipment which is clearly designed or intended for use by young children, the limits of E 71-1 apply. age 44 of 66

45 E Report o.: R2XM A1-03 Zx.2 Equipment requirements o safety provision is required for equipment that complies with the following: - equipment provided as a package (personal music player with its listening device), where the acoustic output L Aeq,T is 85 dba measured while playing the fixed programme simulation noise" as described in E ; and - a personal music player provided with an analogue electrical output socket for a listening device, where the electrical output is 27 mv measured as described in E , while playing the fixed programme simulation noise" as described in E OTE 1 Wherever the term acoustic output is used in this clause, the 30 s A-weighted equivalent sound pressure level L Aeq,T is meant. See also Zx.5 and Annex Zx. All other equipment shall: a) protect the user from unintentional acoustic outputs exceeding those mentioned above; and b) have a standard acoustic output level not exceeding those mentioned above, and automatically return to an output level not exceeding those mentioned above when the power is switched off; and c) provide a means to actively inform the user of the increased sound pressure when the equipment is operated with an acoustic output exceeding those mentioned above. Any means used shall be acknowledged by the user before activating a mode of operation which allows for an acoustic output exceeding those mentioned above. The acknowledgement does not need to be repeated more than once every 20 h of cumulative listening time; and OTE 2 Examples of means include visual or audible signals. Action from the user is always required. age 45 of 66

46 E Report o.: R2XM A1-03 OTE 3 The 20 h listening time is the accumulative listening time, independent how often and how long the personal music player has been switched off. d) have a warning as specified in Zx.3; and e) not exceed the following: 1) equipment provided as a package (player with its listening device), the acoustic output shall be 100 dba measured while playing the fixed programme simulation noise" described in E ; and 2) a personal music player provided with an analogue electrical output socket for a listening device, the electrical output shall be 150 mv measured as described in E , while playing the fixed programme simulation noise" described in E For music where the average sound pressure (long term L Aeq,T ) measured over the duration of the song is lower than the average produced by the programme simulation noise, the warning does not need to be given as long as the average sound pressure of the song is below the basic limit of 85 dba. In this case T becomes the duration of the song. OTE 4 Classical music typically has an average sound pressure (long term L Aeq,T ) which is much lower than the average programme simulation noise. Therefore, if the player is capable to analyse the song and compare it with the programme simulation noise, the warning does not need to be given as long as the average sound pressure of the song is below the basic limit of 85 dba. For example, if the player is set with the programme simulation noise to 85 dba, but the average music level of the song is only 65 dba, there is no need to give a warning or ask an acknowledgement as long as the average sound level of the song is not above the basic limit of 85 dba. age 46 of 66

47 E Report o.: R2XM A1-03 Zx.3 Warning The warning shall be placed on the equipment, or on the packaging, or in the instruction manual and shall consist of the following: - the symbol of Figure 1 with a minimum height of 5 mm; and - the following wording, or similar: To prevent possible hearing damage, do not listen at high volume levels for long periods. Alternatively, the entire warning may be given through the equipment display during use, when the user is asked to acknowledge activation of the higher level. Zx.4 Requirements for listening devices (headphones and earphones) Zx.4.1 Wired listening devices with analogue input With 94 dba sound pressure output L Aeq,T, the input voltage of the fixed programme simulation noise" described in E shall be 75 mv. This requirement is applicable in any mode where the headphones can operate (active or passive), including any available setting (for example built-in volume level control). OTE The values of 94 dba - 75 mv correspond with 85dBA - 27 mv and 100 dba mv. age 47 of 66

48 E Report o.: R2XM A1-03 Zx.4.2 Wired listening devices with digital input With any playing device playing the fixed programme simulation noise" described in E (and respecting the digital interface standards, where a digital interface standard exists that specifies the equivalent acoustic level), the acoustic output L Aeq,T of the listening device shall be 100 dba. This requirement is applicable in any mode where the headphones can operate, including any available setting (for example built-in volume level control, additional sound feature like equalization, etc.). OTE An example of a wired listening device with digital input is a USB headphone. Zx.4.3 Wireless listening devices In wireless mode: - with any playing and transmitting device playing the fixed programme simulation noise described in E ; and - respecting the wireless transmission standards, where an air interface standard exists that specifies the equivalent acoustic level; and - with volume and sound settings in the listening device (for example built-in volume level control, additional sound feature like equalization, etc.) set to the combination of positions that maximize the measured acoustic output for the above-mentioned programme simulation noise, the acoustic output L Aeq,T of the listening device shall be 100 dba. OTE An example of a wireless listening device is a Bluetooth headphone. Zx.5 Measurement methods Measurements shall be made in accordance with E or E as applicable. Unless stated otherwise, the time interval T shall be 30 s. OTE Test method for wireless equipment provided without listening device should be defined. age 48 of 66

49 E Report o.: R2XM A1-03 Annex Zx (A12:2011) Significance of L Aeq,T in E and additional information L Aeq,T is derived from the general formula for equivalent sound pressure: This can be represented graphically as follows: In E the measurement time interval (t2 -t1) is 30 s. In practice, and for the purposes of listening to personal music player content, L Aeq,T has a time interval T (t2 - t1) in the order of minutes / hours and not seconds. 6.5 (Limitation value) of E :2000 acknowledges this fact and states that the 100 db limit equates to a long time average of 90 db L Aeq,T. By using the IEC programme simulation noise" test signal, this also takes the spectral content into account. The SCEHIR 1 report states that 80 dba is considered safe for an exposure time of 40 h/week. Most persons do not listen to 40 h/week to their personal music player. In addition, not all music tracks are at the same level of the simulated noise signal. Whilst modern music tends to be at around the same level, most of the available music is at a lower average level. Therefore, the working group 2 considers a value of 85 dba to be safe for an overwhelming majority of the users of personal music players. age 49 of 66

50 E Report o.: R2XM A SCEIHR opinion of 23 Sept 2008: otential health risks of exposure to noise from personal music players and mobile phones including a music playing function 2 CEELEC TC108X/WG03 ZD IEC and CEELEC code designations for flexible cords Type of flexible cord Code designations IEC CEELEC VC insulated cords Flat twin tinsel cord IEC 41 H03VH-Y Light polyvinyl chloride sheathed flexible cord IEC 52 H03VV-F H03VVH2-F Ordinary polyvinyl chloride sheathed flexible cord IEC 53 H05VV-F H05VVH2-F Rubber insulated cords Braided cord IEC 51 H03RT-F Ordinary tough rubber sheathed flexible cord IEC 53 H05RR-F Ordinary polychloroprene sheathed flexible IEC 57 H05R-F cord Heavy polychloroprene sheathed flexible cord IEC 66 H07R-F Cords having high flexibility Rubber insulated and sheathed cord IEC 86 H03RR-H Rubber insulated, crosslinked VC sheathed IEC 87 H03RV4-H cord Crosslinked VC insulated and sheathed cord IEC 88 H03V4V4-H age 50 of 66

51 E Report o.: R2XM A TABLE: List of critical components Object/part o. lastic Enclosure CB Manufacturer/ trademark CHI MEI CORORATIO ZHEJIAG ZAO ELECTROIC TECHOLOGY CO LTD Type/model Technical data Standard (Edition / year) Mark(s) of conformity 1 ) A-110(+) V-2, 105 C UL 94, UL 746 UL E56070 J-D V-0, 130 C UL 796 UL E Alt V-0, 130 C UL 796 UL Speaker Ω, 3W Transformer (T4) SHE ZHE MOVA IDUSTRIAL CO.,LTD -- Magnet SUTEK HOLDIGS wire LIMITED -- Bobbin SUMITOMO BAKELITE CO LTD -- Insulation Jingjiang Yahua tape ressure Sensitive -- EOXY RESI Glue Co Ltd DOGGUA EATTO ELECTROIC MATERIAL CO LTD MD2152W Class B E Tested with 180 C UL 1446 UL E M C, V-0 UL 94, UL 746 UL E41429 CT 130 C UL 510 UL E E-500 (XX) 130 C UL 94, UL 746 UL E ) An asterisk indicates a mark which assures the agreed level of surveillance TABLE: Opto Electronic Devices Manufacturer...: -- Type...: -- Separately tested...: -- Bridging insulation...: -- External creepage distance...: -- Internal creepage distance...: -- Distance through insulation...: -- Tested under the following conditions...: -- Input...: -- Output...: -- Supplementary information: TABLE: Electrical data (in normal conditions) U (V) I (A) Irated (A) (W) Fuse # Ifuse (A) Condition/status 12.0VDC Max. normal operating Supplementary information: age 51 of 66

52 E Report o.: R2XM A c) 1) TABLE: max. V, A, VA test Voltage (rated) (V) Current (rated) (A) Voltage (max.) (V) Current (max.) (A) VA (max.) (VA) Supplementary information: c) 2) TABLE: stored energy Capacitance C (µf) Voltage U (V) Energy E (J) supplementary information: TABLE: discharge test Condition τ calculated (s) τ measured (s) t u 0V Comments supplementary information: 2.2 TABLE: evaluation of voltage limiting components in SELV circuits Component (measured between) Max. voltage (V) (normal operation) Voltage Limiting Components V peak V d.c Fault test performed on voltage limiting components Voltage measured (V) in SELV circuits (V peak or V d.c.) supplementary information: see clause TABLE: limited current circuit measurement Location Voltage (V) Current (ma) Comments age 52 of 66

53 E Report o.: R2XM A1-03 supplementary information: 2.5 TABLE: limited power sources Circuit output tested: Measured Uoc (V) with all load circuits disconnected: Conditions: Uoc (V) Isc (A) VA Meas. Limit Meas. Limit Supplementary information: and TABLE: ground continue test Location resistant measures (Ω) comments supplementary information: Table: working voltage measurement Location RMS voltage (V) eak voltage (V) Comments Transformer T2 pin Transformer T2 pin Transformer T2 pin Transformer T2 pin Transformer T2 pin Transformer T2 pin Transformer T2 pin Transformer T2 pin Optocoupler U13 pin Optocoupler U13 pin Optocoupler U13 pin Optocoupler U13 pin Q7 pin DC Q7 pin DC Q7 pin 5-GD DC age 53 of 66

54 Report o.: R2XM A1-03 E Q7 pin 4-GD DC supplementary information: and TABLE: Clearance and creepage distance measurements Clearance (cl) and creepage distance (cr) at/of/between: U peak (V) U r.m.s. (V) Required cl (mm) cl (mm) Required cr (mm) cr (mm) Basic/supplementary: TV-2 circuits to accessible enclosure > >10.0 Supplementary information: TABLE: Distance through insulation measurements Distance through insulation (DTI) at/of: U peak U rms Test Required DTI (V) (V) voltage (V) DTI (mm) (mm) Supplementary information: TABLE: Batteries The tests of are applicable only when appropriate battery - data is not available Is it possible to install the battery in a reverse polarity position? - Max. current during normal condition Max. current during fault condition Test results: on-rechargeable batteries Meas. Current (A) Discharging Manuf. Specs. (A) Unintentional charging Meas. Current (A) Rechargeable batteries Charging Discharging Reversed charging Manuf. Specs. (A) Meas. Current (A) Manuf. Specs. (A) Meas. Current (A) Manuf. Specs. (A) Verdict age 54 of 66

55 E Report o.: R2XM A Chemical leaks - Explosion of the battery - Emission of flame or expulsion of molten metal - Electric strength tests of equipment after completion of tests Supplementary information: TABLE: Batteries Battery category...: Manufacturer...: Type / model...: Voltage...: Capacity...: Tested and Certified by (incl. Ref. o.)...: Circuit protection diagram...: MARKIGS AD ISTRUCTIOS (1.7.13) Location of replaceable battery Language(s).: Close to the battery.: In the servicing instructions... : In the operating instructions..: 4.5 TABLE: Thermal requirements Supply voltage (V)...: 12.0VDC -- Ambient T min ( C)...: 22.9 Adjust to Ambient T max ( C)...: 23.2 Tma=60 -- Maximum measured temperature T of part/at:: T ( C) Allowed Tmax ( C) lastic enclosure outside front lastic enclosure inside near U Ref. Metal enclosure outside side CB near CU CB near U Supplementary information: age 55 of 66

56 E Report o.: R2XM A1-03 Temperature T of winding: t 1 ( C) R 1 (Ω) t 2 ( C) R 2 (Ω) T ( C) Allowed Tmax ( C) Insulation class Supplementary information: TABLE: Ball pressure test of thermoplastic parts Allowed impression diameter (mm)... : 2 mm art Test temperature ( C) Impression diameter (mm) Supplementary information: 4.7 TABLE: Resistance to fire art Manufacturer of material Type of material Thickness (mm) Flammability class Evidence Supplementary information: See appended table TABLE: touch current measurement Measured between: Measured (ma) Limit (ma) Comments/conditions supplementary information: 5.2 TABLE: Electric strength tests, impulse tests and voltage surge tests Test voltage applied between: Basic/supplementary: Voltage shape (AC, DC, impulse, surge) Test voltage (V) Breakdown Yes / o TV circuits to accessible enclosure DC 744 o Supplementary information: 5.3 TABLE: Fault condition tests Ambient temperature ( C)... : age 56 of 66

57 Report o.: R2XM A1-03 E ower source for EUT: Manufacturer, model/type, output rating... : -- Component o. Fault Supply voltage (V) Test time Fuse # Fuse current (A) Observation Q7 pin 4-5 Short circuited 12VDC 15mins Unit shut down immediately, no fire or molten metal occured, no hazard. T2 pin 4-9 Short circuited 12VDC 15mins Unit shut down immediately, no fire or molten metal occured, no hazard. T2 pin 8-9 Short circuited 12VDC 15mins Unit shut down immediately, no fire or molten metal occured, no hazard. T2 pin 3-4 Short circuited 12VDC 15mins Unit shut down immediately, no fire or molten metal occured, no hazard. T2 pin 8-9 Overload 12VDC 15mins The overload could not be happenned and unit shut down immediately, no fire or molten metal occured, no hazard. D18 Short circuited 12VDC 15mins Unit working normally, no fire or molten metal occured, no hazard. D21 Short circuited 12VDC 15mins Unit shut down immediately, no fire or molten metal occurs, no hazards. D89 Short circuited 12VDC 15mins Unit shut down immediately, no fire or molten metal occurs, no hazards. C21 Short circuited 12VDC 15mins Unit shut down immediately, no fire or molten metal occured, no hazard. Speaker Short circuited 12VDC 15mins o voice, others normal, recoverable, no fire or molten metal occured, no hazard. Supplementary information: C.2 TABLE: transformers Loc. Tested insulation Working voltage peak / V (2.10.2) Working voltage rms / V (2.10.2) Required electric strength (5.2) Required clearance / mm (2.10.3) Required creepage distance / mm (2.10.4) Required distance thr. insul. (2.10.5) age 57 of 66

58 E Report o.: R2XM A1-03 Loc. Tested insulation Test voltage/ V Measured clearance / mm Measured creepage dist./ mm supplementary information: -- Measured distance thr. insul. / mm; number of layers C.2 TABLE: transformers age 58 of 66

59 Report o.: R2XM A1-03 Appendix A - EUT HOTOS hoto 1 overall view hoto 2 back view age 59 of 66

60 Report o.: R2XM A1-03 hoto 3 internal view hoto 4 internal view age 60 of 66

61 Report o.: R2XM A1-03 hoto 5 main board top view hoto 6 main board bottom view age 61 of 66

62 Report o.: R2XM A1-03 hoto 7 ID card reader board top view hoto 8 ID card reader board top view age 62 of 66

63 Report o.: R2XM A1-03 hoto 9 IC card reader board top view hoto 10 IC card reader board bottom view age 63 of 66

64 Report o.: R2XM A1-03 hoto 11 IR-LED board top view hoto 12 IR-LED board bottom view age 64 of 66

65 Report o.: R2XM A1-03 hoto 13 key board top view hoto 14 key board bottom view age 65 of 66