Requirements for Electrical Installations - BS 7671: 2008 incorporating Amendment No.3, 2015 [IETWiring Regulations]

Size: px

Start display at page:

Download "Requirements for Electrical Installations - BS 7671: 2008 incorporating Amendment No.3, 2015 [IETWiring Regulations]"

Cori Flynn
5 years ago
Views:

1 Electrical ertifi cate Installation/Modification Requirements for Electrical Installations - S : 2008 incorporating Amendment No.3, 205 [IETWiring Regulations] This safety ertifi cate has been issued to confi rm that the electrical installation work to which it relates has been designed, constructed, inspected and tested in accordance with ritish Standard (the let Wiring Regulations). 2 You should have received an original ertifi cate and the contractor should have retained a duplicate. If you were the person ordering the work, but not the owner of the installation, you should pass this ertifi cate, or a full copy of it including the schedules, immediately to the owner. 3 The original ertifi cate should be retained in a safe place and be shown to any person inspecting or undertaking further work on the electrical installation in the future. If you later vacate the property, this ertificate will demonstrate to the new owner that the electrical installation complied with the requirements of ritish Standard at the time the ertifi cate was issued. 5 The onstruction (Design and Management) Regulations require that, for a project covered by those Regulations, a copy of this ertifi cate, together with schedules, is included in the project health and safety documentation. For safety reasons, the electrical installation will need to be inspected at appropriate intervals by a skilled person competent in such work. The maximum time interval recommended before the next inspection is stated on Page under NEXT INSPETION. This ertifi cate is intended to be issued only for a new electrical installation or for new work associated with an addition or alteration to an existing installation. It should not have been issued for the inspection of an existing electrical installation. An Electrical Installation ondition Report should be issued for such an inspection. 8 This ertifi cate is only valid if accompanied by the schedule of inspections and the schedule(s) of test results opyright PIT July 205 PIT Administration entre, th Floor, Mill 3, Pleasley Vale usiness Park, Mansfi eld, Nottinghamshire NG9 8RL /E/00 (V)

2 2 3 5 Electrical ertifi cate Installation/Modification Requirements for Electrical Installations S : 2008 incorporating Amendment No.3,205 [IET Wiring Regulations th Edition] All items inspected to confirm as appropriate, compliance with the relevant clauses in S Details of the Installation lient Address Postcode Description, extent and limitations of the Installation (note 5) / Page Installation (If different from client) OMMUNITY ENTRE Address LANASTER WAY OFF ORDANE WAY UKSHAW VILLAGE, LANASHIRE Postcode Installation is New Addition Alteration Records available No Date of original Installation Description of installation NEW UILD ALL WIRING Extent of installation covered by this ertificate Details of departure from S (Regulations 20.3 and 33.5) Details of permitted exceptions. [Regulation.3.3] Where applicable a suitable risk assessment[s] must be attached to this certificate Risk assessment attached For design, construction, Inspection and testing [for sole person responsibility.] I being the person responsible for design, construction, inspection and test of the electrical installation (as indicated by my signature below), particulars of which are described in Section 2, having exercised reasonable skill and care when carrying out the design, construction, inspection and test hereby ERTIFY that the design,construction, inspection and test for which I have been responsible is to the best of my knowledge and belief in accordance with S :2008, amended to 205 (date) The extent of liability of the signatory or the signatories is limited to the work described In Section 2 as subject of this certificate. Next inspection I/We the designer[s] recommend that this Installation Is further For the DESIGN / ONSTRUTION / INSPETION AND TEST of the installation: Inspected after an Interval of not more than 5 years ompany name Installer ompany address Postcode IVOR FARNWORTH PRIMROSE HOLDINGS, HEYS FARM HORLEY, LANASHIRE PR 8EW N W Electrical & onstruction Limited Wayne Howson Miry Fold Farm riers row HORLEY, Lancashire Supply characteristics and earthing arrangements Earthing Arrangements TN-S TN--S TT Other Please specify: Position electrician Date 0/0/20 PIT membership No. 905 Hz onfi rmation of supply polarity Prospective fault current, I pf ( 2 ).0 ka External loop Impedance, Z e ( 2 ).2 Ω Supply Protective Device S 3 Type 2 Nominal urrent Rating 00 A Other Sources of Supply Particulars of installation referred to in this certificate Means of Earthing Distributor s facility Installation earth electrode Details of installation Earth Electrode (where applicable) Type (e.g. rod(s), tape etc) demand Location Electrode resistance to earth Ω Demand (load) 80 Amps Main Protective onductors Material sa (mm 2 ) Verified (connection / continuity) Earthing onductor opper Water installation Structural steel Protective onding onductor opper 0 Gas installation pipes Lightning protection Main Supply onductor opper 25 Oil installation pipes Other Main Switch Location KITHEN S(EN) 09-3 No. of Poles 3 urrent Rating 00 A Fuse/device rating or setting 00 A Voltage rating 2 V If RD main switch: Rated residual operating current I n = ma Rated time delay ms (at I n) Measured operating trip time ms omments on existing installation (In the case of addition or alteration see Section 33) PR LJ Number a type of live conductors ac. d.c. No. of phases No. of wires 2 Nature of Supply Parameters (Note: ( ) by enquiry, ( 2 ) by enquiry or by measurement) Nominal voltage, U/U O ( ) 2 V Nominal frequency, f( 2 ) 50 NEW UILD PR 8JN (For additions or alterations) cables concealed within trunking and conduits, or cables or conduits concealed under fl oors, in roof spaces and generally within the fabric of the building or underground may not have been Inspected. Schedule of Inspections attached ALL IRUITS * * * * * * * * 0/0/20 of opyright PIT July 205 PIT Administration entre, th Floor, Mill 3, Pleasley Vale usiness Park, Mansfi eld, Nottinghamshire NG9 8RL /E/00 (V)

3 A Inspector s Name Date Electrical ertificate Installation/Modification Inspection Schedule for Domestic and Similar Premises with up to 00A Supply Requirements for Electrical Installations S : 2008 incorporating Amendment No.3,205 [IET Wiring Regulations th Edition] Schedule of Inspections Outcomes Acceptable condition: Not applicable: (In the Outcome column use the codes above. Item No. Description Outcome.0 DISTRIUTOR S / SUPPLY INTAKE EQUIPMENT. ondition of service cable.2 ondition of service head.3 ondition of distributor's earthing arrangement. ondition of meter tails - Distributor / onsumer.5 ondition of metering equipment. ondition of isolator (where present) 2.0 PARALLEL OR SWITHED ALTERTIVE SOURES OF SUPPLY 2. Adequate arrangements where a generator set operates as a switched alternative to the public supply [55.] 2.2 Adequate arrangements where a generator set operates in parallel with the public supply [55.] 3.0 AUTOMATI DISONNETION OF SUPPLY 3. Presence and adequacy of earthing and protective bonding arrangements: 3.. Installation earth electrode [where applicable] [ ] 3..2 Earthing conductor and connections, including accessibility [52.3;53.3.2] 3..3 Main protective bonding conductors and connection, including accessibility [.3..2; ] 3.. Provision of safety electrical earthing / bonding labels at all appropriate locations [5.3] 3..5 RD(s) provided for fault protection [..9;.5.3].0 ASI PROTETION. Presence and adequacy of measures to provide basic protection (prevention of contact with live parts) within the installation:.. Insulation of live parts e.g. conductors completely covered with durable insulating material [.]..2 arriers and enclosures e.g correct IP Rating [.2] 5.0 ADDITIOL PROTETION 5. Presence and effectiveness of methods: 5.. RD(s) not exceeding ma operating current [5.; Part ] see item 8. of this schedule 5..2 Supplementary bonding [5.2; Part ].0 OTHER METHODS OF PROTETION. Presence and effectiveness of methods which give both basic and fault protection:.. SELV system, including the source and associated circuits [Section ]..2 PELV system, including the source and associated circuits [Section ]..3 Double or reinforced insulation i.e.lass II or equivalent equipment and associated circuits [Section 2].. Electrical separation for one item of equipment e.g. shaver supply unit [Section 3].0 ONSUMER UNIT(S) / DISTRIUTION OARD(S). Adequacy of access and working space for items of electrical equipment including switchgear [.2].2 Presence of linked main switch(s) [53..; 53..5; 53..].3 Isolators, for every circuit or group of circuits and all items of equipment [53.2] Wayne Howson 0/0/20 / * * * * * * * * Page 2 of opyright PIT June 205 PIT Administration entre, th Floor, Mill 3, Pleasley Vale usiness Park, Mansfi eld, Nottinghamshire NG9 8RL /EI/IS/00 (V)

4 A Inspector s Name Date Electrical ertificate Installation/Modification Inspection Schedule for Domestic and Similar Premises with up to 00A Supply Requirements for Electrical Installations S : 2008 incorporating Amendment No.3,205 [IET Wiring Regulations th Edition] Schedule of Inspections Outcomes Acceptable condition: Not applicable: (In the Outcome column use the codes above. Item No. Description Outcome. Suitability of enclosure[s] in terms of IP and fi re rating [.2; 2..; 2..20].5 Protection against mechanical damage where cables enter equipment [522.8.; ]. onfi rmation that ALL conductor connections are correctly located in terminals and are tight and secure [52.]. Avoidance of heating effects where cables enter ferromagnetic enclosures e.g. steel [5].8 Selection of correct type and ratings of circuit protective devices for overcurrent and fault protection [.3.2;.,.5,.; Sections,33].9 Presence of appropriate circuit charts, warning and other notices:.9. Provision of circuit charts / schedules or equivalent forms of information [5.9].9.2 Warning notice of method of isolation where live parts not capable of being isolated by a single device [5.].9.3 Presence of inspection and testing notice [5.2.].9. RD quarterly test notice; where required [5.2.2].9.5 Warning notice of non-standard (mixed) cable colour of conductors present [5.].0 Presence of labels I indicate the purpose of switchgear and protective devices [5..; 5.8] 8.0 FIL IRUITS 8. Adequacy of cables for current-carrying capacity with regard for the type and nature of the installation [Section 523] 8.2 able installation methods suitable for the location(s) and external infl uences [Section 522] 8.3 Segregation / separation of and I (ELV) from and I (LV) circuits, and electrical and non-electrical services[528] 8. ables correctly erected and supported throughout including escape routes, with protection against abrasion [Sections 52, 522] 8.5 Provision of fi re barriers, sealing arrangements where necessary [52.2] 8. Non-sheathed cables enclosed throughout in conduit, ducting or trunking [52.0.; 52.8] 8. ables concealed under fl oors, above ceilings or in walls / partitions, adequately protected against damage. [ ; 202; 20] 8.8 onductors correctly identifi ed by colour, lettering or numbering [Section 5] 8.9 Presence, adequacy and correct termination of circuit protective conductors [.3..; 53.] 8.0 ables and conductors correctly connected, enclosed and with no undue mechanical strain [Section 52] 8. No basic insulation of a conductor visible outside enclosure [52.8] 8.2 Single-pole devices for switching or protection in line conductors only [..; 5.3.2] 8.3 Accessories not damaged, securely fi xed, correctly connected, suitable for external infl uences [3..; 52.2; Section 52] 8. Provision of additional protection by RD not exceeding ma: 8.. Socket-outlets rated at 20 A or less unless exempt [Regulation.3.3] 8..2 Mobile equipment with a current rating not exceeding A for use outdoors [.3.3] 8..3 ables concealed in walls at a depth of less than 50mm [ ; ] 8.. ables concealed in walls / partitions containing metal parts regardless of depth [ ] 8.5 Presence of appropriate devices for isolation and switching correctly located including: 8.5. Means of switching off for mechanical maintenance [53.3] Wayne Howson 0/0/20 / * * * * * * * * Page 3 of opyright PIT June 205 PIT Administration entre, th Floor, Mill 3, Pleasley Vale usiness Park, Mansfi eld, Nottinghamshire NG9 8RL /EI/IS/00 (V)

5 A Inspector s Name Date Schedule of Inspections Outcomes Acceptable condition: Not applicable: (In the Outcome column use the codes above. Item No. Description Outcome Emergency switches [53.] Functional switches, for control of parts of the installation and current-using equipment [53.5] 8.5. Firefi ghters switches [53.] 9.0 URRENT-USING EQUIPMENT (PERMANENTLY ONNETED) 9. Equipment not damaged, securely fi xed and suitable for external infl uences [3..;.2; 52.2] 9.2 Provision of overload and / or undervoltage protection e.g. rotating machines, if required [Sections 5; 552] 9.3 Installed to minimize the build-up of heat and restrict the spread of fi re [2..; ] 9. Adequacy of working space. Accessibility to equipment [.2; 53.] 0.0 LOATION(S) ONTAINING A ATH OR SHOWER 0. ma RD protection for all LV circuits, equipment suitable for the zones, supplementary bonding (where required) [Sections 5; 552]. OTHER SPEIAL INSTALLATIONS OR LOATIONS. List all other special installations or locations present, if any. [Record separately the results of particular inspections applied] Schedule of Tests Results to be recorded on Schedule of Test Results Electrical ertificate Installation/Modification Inspection Schedule for Domestic and Similar Premises with up to 00A Supply Requirements for Electrical Installations S : 2008 incorporating Amendment No.3,205 [IET Wiring Regulations th Edition] External earth loop Impedance, Ze Installation earth electrode Prospective fault current lpf ontinuity of Earth onductors ontinuity of ircuit Protective onductors ontinuity of ring fi nal conductors ontinuity of Protective onding onductors Volt drop verifi ed Wayne Howson 0/0/20 / Insulation Resistance between Live conductors Insulation Resistance between Live conductors & Earth Polarity (Prior to energisation) Polarity (prior to energisation) Polarity (after energisation) including phase sequence Earth fault loop impedance RDs / ROs including discrimination Functional testing of devices. (insert or ) Page * * * * * * * * of opyright PIT June 205 PIT Administration entre, th Floor, Mill 3, Pleasley Vale usiness Park, Mansfi eld, Nottinghamshire NG9 8RL /EI/IS/00 (V)

6 lient IVOR FARNWORTH Installation address LANASTER WAY, OFF ORDANE WAY, UKSHAW VILLAGE, LANASHIRE Postcode PR LJ omplete in every case omplete only if the distribution board is not connected directly to the origin of the installation Test instrument serial number(s) Location of Supply to distribution haracteristics at this distribution board Associated RD Earth fault distribution board KITHEN board is from (if any): S (EN) loop imped Distribution board Overcurrent protective device No. of Nominal V Z Operating At I Insulation n ms designation D for the distribution circuit: phases Voltage times of RD resistance I n ma ontinuity Number of ways Type S(EN) Rating A I associated No of pf ka at 5 I n ms RD(if any) Poles Supply polarity confirmed Phase sequence confirmed RD ircuit No. ircuit designation IRUIT DETAILS Type of wiring Ref. method No. of points served ircuit conductors csa Live (mm 2 ) P (mm 2 ) disconnection time (S:) Details of circuits and/or installed equipment vulnerable to damage when testing Tested by: Name (capital letters) Position Electrical ertificate Installation/Modification Test Schedule for Domestic and Similar Premises with up to 00A Supply Requirements for Electrical Installations S :2008 incorporating Amendment No [IET Wiring Regulations th Edition] HALL SOKETS KITHEN SOKETS HO Oven KITHEN WATER HEATER WATER OILER JANITOR WATER HEATR SeRVER SOKET StREET LIGHTS HYDRO OIL ALARM / FIRE ALARM PANEL URGULAR ALARM PANEL ELETRIIAN WAYNE HOWSON (S) TEST RESULTS Overcurrent protective devices S ircuit impedence Insulation resistance RD testing Max. (Record lower reading) permitted value Z All circuits to be s Test Other Ring final circuits only completed using Live / Live / measured utton S EN Number Type Rating 80% (measured end to end) R R2, or R2, not both Live Earth Z s at I n at 5 I n operation No. (A) (ka) (ma) r r n r 2 ( ) R +R 2 R 2 (M ) (M ) ( ) ( ) ms ms ( ) reaking capacity RD operating current I n Date Not Specified Figure 8 check * * * * * * * * Wiring Types = PV/PV 2= Single Insulated in onduit or Trunking 3= Mineral Insulated = SWA/XPLE 5= FP Polarity opyright PIT January 205 This form is based on the requirements of Appendix of S PIT Administration entre, th Floor, Mill 3, Pleasley Vale usiness Park, Mansfield, Nottinghamshire NG9 8RL

7 ircuit No. for Domestic and Similar Premises with up to 00A Supply Requirements for Electrical Installations S :2008 incorporating Amendment No.3, 205 [IET Wiring Regulations th Edition] ircuit designation Tested by: Name (capital letters) Position Electrical ertificate Installation/ModificationTest Schedule ontinuation (ontinuation) IT SUITE SOKETS TOILET HEATER HEATING StREET LIGHT SIDE Fire Alarm TOILET JANITOR HALL RING LOFT LIGHTS HALL LIGHTS 5 IRUIT DETAILS Type of wiring / Ref. method No. of points served ircuit conductors csa Live (mm 2 ).5 P (mm 2 ) disconnection time (S:) (S) TEST RESULTS Overcurrent protective devices S ircuit impedence Insulation resistance RD testing Max. (Record lower reading) permitted value Z All circuits to be s Test Other Ring final circuits only completed using Live / Live / measured utton S EN Number Type Rating 80% (measured end to end) RR2,orR2,notboth Live Earth Z s at I n at 5 I n operation No. (A) (ka) (ma) r r n r 2 ( ) R +R 2 R 2 (M ) (M ) ( ) ( ) ms ms ( ) 009 reaking capacity RD operating current I n WAYNE HOWSON Wiring Types = PV/PV 2= Single Insulated in onduit or Trunking 3= Mineral Insulated = SWA/XPLE 5= FP200 ELETRIIAN D ENTRANE W AND JANITOR TOILET & KITHEN LIGHTS / Date(s) Not Specified Figure 8 check * * * * * * * * Polarity PIT Administration entre, th Floor, Mill 3, Pleasley Vale usiness Park,Mansfield, Nottinghamshire NG9 8RL /EI/F/00 (V3)

8 ircuit No. for Domestic and Similar Premises with up to 00A Supply Requirements for Electrical Installations S :2008 incorporating Amendment No.3, 205 [IET Wiring Regulations th Edition] ircuit designation Tested by: Name (capital letters) Position Electrical ertificate Installation/ModificationTest Schedule ontinuation (ontinuation) IRUIT DETAILS Type of wiring Ref. method No. of points served ircuit conductors csa 3 Live (mm 2 ) P (mm 2 ) disconnection time (S:) Wiring Types = PV/PV 2= Single Insulated in onduit or Trunking 3= Mineral Insulated = SWA/XPLE 5= FP200 ELETRIIAN D WAYNE HOWSON (S) TEST RESULTS Overcurrent protective devices S ircuit impedence Insulation resistance RD testing Max. (Record lower reading) permitted value Z All circuits to be s Test Other Ring final circuits only completed using Live / Live / measured utton S EN Number Type Rating 80% (measured end to end) RR2,orR2,notboth Live Earth Z s at I n at 5 I n operation No. (A) (ka) (ma) r r n r 2 ( ) R +R 2 R 2 (M ) (M ) ( ) ( ) ms ms ( ) reaking capacity RD operating current I n Date(s) Not Specified Figure 8 check * * * * * * * * Polarity PIT Administration entre, th Floor, Mill 3, Pleasley Vale usiness Park,Mansfield, Nottinghamshire NG9 8RL /EI/F/00 (V3)

MinorWorks/Single Circuit Electrical Certificate

MinorWorks/Single Circuit Electrical Certificate Requirements for Electrical Installations BS767 [IET Wiring Regulations] Information for recipients : This safety Certificate for Minor Works/ Single Circuit