04 Page. MCCBs characteristics 94. MCCBs & accessories selection guide 96. MCCBs x MCCBs x MCCBs h

Transcription

1 This section includes moulded case circuit breakers, manual and automatic transfer switches and load break switches which are utilised for the switching, protection and distribution of low voltage installations.

2

3 04 Page MCCBs characteristics 94 MCCBs & accessories selection guide 96 MCCBs x60 00 MCCBs x MCCBs h MCCBs h MCCBs h MCCBs h600 0 DIN NH fuses and fuse carriers 2 Load break switches 3 Manual transfer switches 5 Automatic transfer switches 6 Fuse combination switches 7 Earth leakage relays and toroids 8 Technical information 9

4 MCCBs - characteristics Product x60 TM MCCB x250 TM MCCB Reference HHA HNA HNB Number of poles [No.] Electrical characteristics Rated current In [A] Current rated range [A] Rated service voltage, (AC) Ue [V] Frequency f [Hz] 50/60 50/60 Rated insulation voltage Ui [V] Rated impulse withstand voltage Uimp [kv] 8 8 Rated ultimate short-circuit breaking capacity, (Icu) (AC) 50-60Hz 220/230V Icu [ka] (AC) 50-60Hz 380/45V Icu [ka] (AC) 50-60Hz 480/500/525V Icu [ka] (AC) 50-60Hz 660/690V Icu [ka] (DC) 250V - 2 poles in series Icu [ka] Rated service short-circuit breaking capacity, (Ics) (AC) 50-60Hz 220/230V Ics [ka] (AC) 50-60Hz 380/45V Ics [ka] (AC) 50-60Hz 480/500/525V Ics [ka] (AC) 50-60Hz 660/690V Ics [ka] (DC) 250V - 2 poles in series Ics [ka] Rated short-circuit making capacity Icm [ka] Rated short-time withstand current for s Icw [ka] Category of use (EN ) A A Calibration temperature 50 C 50 C Derating 40 C 00% 00% 50 C 00% 00% 55 C 95% 94% 60 C 93% 9% 65 C 90% 88% Suitability for isolation ok ok Electric endurance in number of cycles Mechanical endurance in number of operations Operating temperature -25 to +70 C -25 to +70 C Storage temperature -35 to +70 C -35 to +70 C Power loss (at In for 3P) [W] Reference standard IEC IEC Releases: switch - - Releases: TM (thermomagnetic) ok ok T fixed, M fixed ok ok T adjustable, M fixed ok - T adjustable, M adjustable - ok Thermal adjustment value 0.63 to 0.8 to x In 0.63 to 0.8 to x In Magnetic adjustment value x In (200A) In (250A) Releases: LSI (electronic) - - Long delay - - Short delay - - Time delay - - Terminations Standard terminal type cage lugs Maximum terminal capacity 95mm 2 85mm 2 (cage) Terminal width mm - 25 Terminal shields ok ok Cage terminal integrated ok Extended connections ok ok Rear connections no ok Dimensions Height mm Width 3P mm P mm Depth mm Weight 3P kg P kg Subject to technical modification / New Ended Replacement

5 MCCBs - characteristics h250 LSI MCCB h400 TM MCCB h630 LSI MCCB h000 LSI MCCB h600 LSI MCCB HNC HEC HND HND HED HNE HEE HNF HEF /60 50/60 50/60 50/60 50/ (800A) (000A) , (800A) 00 (800A) (000A) 75 (000A) B A B (400A) - A (630A) B (800A) - A (000A) B 40 C 50 C 40 C 40 C 40 C 00% 00% 00% 00% 00% 95% 00% 00% 00% 00% 90% 95% 95% 95% 95% 80% 92% 90% 90% 90% 80% 89% 80% 80% 80% ok ok ok ok ok to +70 C -25 to +70 C -25 to +70 C -25 to +70 C -25 to +70 C -35 to +70 C -35 to +70 C -35 to +70 C -35 to +70 C -35 to +70 C IEC IEC IEC IEC IEC ok ok to 0.8 to x In x In ok ok ok 0.4 to x Ir to x Ir 0.4 to x Ir 0.4 to x In 2.5 to 0 x Ir to 0 x Ir (400A) 2.5 to 0 x Ir (800A) 2.5 to 0 x Ir 2.5 to 8 x Ir (630A) 2.5 to 8 x Ir (000A) s s s s lugs lugs lugs lugs lugs 20mm 2 (cage) 240mm 2 (cage) ok ok ok ok ok ok ok ok ok integrated integrated integrated ok ok ok ok ok / / , Subject to technical modification / New Ended Replacement 95

6 MCCBs & accessory selection guide Frame Trip Unit Pole MCCBs Terminal connectors In (A) 25 ka 40 ka Collar Straight Spreader Rear 25 HHA025U HNA025U 40 HHA040U HNA040U 63 HHA063U HNA063U 3 80 HHA080U HNA080U HYA005H HYA03H HYA04H - 00 HHA00U HNA00U 25 HHA25U HNA25U X60 60 HHA60U HNA60U 25 HHA026U HNA026U 40 HHA04U HNA04U TM 63 HHA064U HNA064U 4 80 HHA08U HNA08U HYA006H HYA03H HYA05H - 00 HHA0U HNA0U 25 HHA26U HNA26U 60 HHA6U HNA6U 60 - HNB60U HNB200U HYB00H HYB00H HYB0H HYB03H x HNB250U 60 - HNB6U HNB20U HYB002H HYB00H HYB02H HYB032H HNB25U Frame x60 x250 Operating Voltage Shunt Trips - SH Under Voltage - UV 24V DC HXA00H HXA0H - 48V DC HXA002H - - Motor Operator 00-20V AC HXA003H HXA03H V AC HXA004H HXA04H V AC HXA005H HXA05H - 24V DC HXA00H HXA0H HXB040H 48V DC HXA002H V AC HXA003H HXA03H V AC - - HXB042H V AC HXA004H HXA04H V AC HXA005H HXA05H - Auxilliary Contact (C/O) AUX, AX (NO + NC) HXA02H HXA02H Alarm, AL (NO +NC) HXA024H HXA024H 96 Subject to technical modification / New Ended Replacement

7 MCCBs & accessory selection guide Terminal covers Interlock Phase DIN rail Rotary Handle Collar Straight Spreader Rear Barrier adaptor Direct Extended Padlock HYA027H HYA02H HYA023H - - HYA09H HYA033H HXA030H HXA03H HXA039H HYA028H HYA022H HYA024H - - HYA09H HYA033H HXA030H HXA03H HXA039H HYB027H HYB02H HYB023H HYB025H HXB065H HYB09H - HXB030H HXB03H HXA039H HYB028H HYB022H HYB024H HYB026H HXB065H HYB09H - HXB030H HXB03H HXA039H Subject to technical modification / New Ended Replacement 97

8 MCCBs & accessory selection guide Frame Trip Unit Pole 3 h h630 LSI 4 3 h h600 4 MCCBs Terminal connectors In (A) 50 ka 70 ka Collar Straight Spreader Rear 40 HNC040H HEC040H 25 HNC25H HEC25H HYC003H HYC00H HYC0H HYC03H 250 HNC250H HEC250H 40 HNC04H HEC04H 25 HNC26H HEC26H HYC004H HYC00H HYC02H HYC032H 250 HNC25H HEC25H 400 HND400H HED400H HYD003H HYD00H HYD0H HYD03H 630 HND630H HED630H HYD007H HYD03H HYD04H HYD033H 400 HND40H HED40H HYD004H HYD00H HYD02H HYD032H 630 HND63H HED63H HYD008H HYD03H HYD05H HYD034H 800 HNE800H HEE800H HYE03H HNE970H HEE970H HYE033H 800 HNE80H HEE80H HYE032H HNE97H HEE97H HYE034H 250 HNF980H HEF980H 600 HNF990H HEF990H HNF98H HEF98H 600 HNF99H HEF99H Frame h250 h630 Operating Voltage Shunt Trips - SH Under Voltage - UV Motor Operator 24V DC HXC00H HXC0H HXC040H 48V DC HXC002H V AC HXC003H HXC03H V AC HXC004H HXC04H HXC042H V AC HXC005H HXC05H - 24V DC HXC00H HXC0H HXD040H 48V DC HXC002H - HXD040H 00-20V AC HXC003H HXC03H HXD042H V AC HXC004H HXC04H HXD042H V AC HXC005H HXC05H - Auxilliary Contact (C/O) AUX, AX (NO + NC) HXC02H HXC02H Alarm, AL (NO +NC) HXC024H HXA024H 98 Subject to technical modification / New Ended Replacement

9 MCCBs & accessory selection guide Terminal covers Interphase Rotary handles Interlock Collar Straight Spreader Rear Barrier Direct Extended Padlock HYC027H HYC02H - HYC025H HXC065H HYC09H HXC030H HXC03H HXC039H HYC028H HYC022H - HYC026H HXC065H HYC09H HXC030H HXC03H HXC039H HYD027H HYD02H HYD023H HYD025H HXD065H HYD09H HXD030H HXD03H HXD039H HYD028H HYD022H HYD024H HYD026H HXD065H HYD09H HXD030H HXD03H HXD039H - HYE02H - HYE025H HXE065H - HXE030H HXE03H HXD039H - HYE022H - HYE026H HXE065H - HXE030H HXE03H HXD039H HXF030H HXF03H HXF039H HXF030H HXF03H HXF039H Frame h000 h600 Operating Voltage Shunt Trips - SH Under Voltage - UV Motor Operator 24V DC HXC00H HXE0H HXE040H 48V DC HXC002H - HXE040H 00-20V AC HXC003H HXE03H HXE042H V AC HXC004H HXE04H HXE042H V AC HXC005H HXE05H - 24V DC HXC00H HXE0H HXF040H 48V DC HXC002H V AC HXC003H HXE03H V AC HXC004H HXE04H HXF042H V AC HXC005H HXE05H - Auxilliary Contact (C/O) AUX, AX (NO + NC) HXC02H HXC02H Alarm, AL (NO +NC) HXC024H HXC024H Subject to technical modification / New Ended Replacement 99

10 MCCBs x60 Moulded case circuit breakers x60 - Thermal magnetic trip unit, 2 versions: - Z version: fixed thermal and fixed magnetic - U version: adjustable thermal and fixed magnetic - P, 2P, 3P & 4P - Mechanical test button, sealable settings, integrated padlocking handle Ø4mm. Connection capacity: - 95mm 2 rigid cables - 70mm 2 flexible cables - Comply with IEC Technical information: Page 9 MCCBs x60 25kA Cat ref. Cat ref. Cat ref. Description In P 3P 4P - Breaking capacity Ics: 20kA (400/45V AC) - Fixed thermal x In - Fixed magnetic > 0 x In 6A HHA04Z A HHA08Z A HHA023Z A HHA030Z - - HHA25U 40A HHA038Z A HHA048Z A HHA06Z A HHA078Z Adjustable thermal x In - Fixed magnetic > 0 x In 00A HHA098Z A HHA23Z A - HHA025U HHA026U 40A - HHA040U HHA04U 63A - HHA063U HHA064U HHA6U 80A - HHA080U HHA08U 00A - HHA00U HHA0U 25A - HHA25U HHA26U 60A - HHA60U HHA6U MCCBs x60 40kA Cat ref. Cat ref. Description In 3P 4P - Breaking capacity Ics: 20kA (400/45V AC) - Adjustable thermal x In - Fixed magnetic > 0 x In 25A HNA025U HNA026U 40A HNA040U HNA04U 63A HNA063U HNA064U 80A HNA080U HNA08U HNA25U 00A HNA00U HNA0U 25A HNA25U HNA26U 60A HNA60U HNA6U Switch Disconnector Cat ref. Description In 3P - Suitable for AC22A/ AC23A 25A HCA25Z - Ue: 45V AC 60A HCA60Z - lcw (s): 2kA HCA25Z 00 Subject to technical modification / New Ended Replacement

11 MCCBs x60 - accessories Indication contacts - changeover switch (ON/OFF): indicates the position of the MCCB is open or closed. - changeover alarm contact: indicates MCCB tripping. Coil connection - Connection capacity: 0.75mm flexible or rigid cables. - Optional connection cables. The cable capacity of the terminals is 0.5 to.25mm 2. Shunt trip - Remote tripping of MCCBs or trip-free switches. - Operating voltage: 0.7 to. x Un Under voltage release - Allows the tripping of MCCBs when voltage level drops between 35 and 70% of Un. - Pick up voltage 0.85 x Un Direct rotary handle - Padlockable - Equipped with front cover and handle - Fixing without any additional screw. Extended rotary handle - IP 55 - Supplied complete with shaft and handle. Technical information: Page 2 Accessories Description Characteristics Cat ref. Auxiliary contacts AX AL Shunt trips SH Undervoltage releases UV changeover contact (ON/OFF) HXA02H 250V AC / 3A 25V DC / 0.4A NO + NC changeover alarm contact HXA024H 250V AC / 3A 25V DC / 0.4A NO + NC 24V DC HXA00H 48V DC HXA002H 00-20V AC HXA003H V AC HXA004H V AC HXA005H 24V DC HXA0H 00-20V AC HXA03H V AC HXA04H V AC HXA05H HXA02H HXA004H HXA024H HXA04H Accessories Cat ref. Cat ref. Description Direct rotary handle Padlockable Characteristics 3P 4P Max Ø 6mm HXA030H HXA030H Extended rotary handle Padlockable Padlocking device To mount on MCCB for handle locking 3 padlocks Collar terminals Terminals for aluminium conductor Max Ø 8mm 200mm HXA03H HXA03H Max Ø 8mm HXA039H HXA039H Set of 3 or 4 HYA005H HYA006H Extended connections Straight connections - set of 4 HYA03H HYA03H Spreader connections - set of 3 or 4 HYA04H HYA05H Interphase barriers Set of 2 HYA09H HYA09H Height: 50mm Terminal covers - 2 pcs For extended straight connections HYA02H HYA022H For extended spreader connections HYA023H HYA024H For collar terminal HYA027H HYA028H Din rail adaptor HYA033H HYA033H HXA03H HYA05H HYA02H Subject to technical modification / New Ended Replacement 0

12 MCCBs x250 Moulded case circuit breakers x250 - Adjustable thermal and magnetic trip unit - 3P and 4P - Mechanical test button - Lockable settings - Integrated padlocking handle Ø 4mm - Complies with IEC Connection: - Terminal area width 25mm Connection capacity: - 85mm 2 rigid cables - Collar terminals optional Technical information: Page 25 MCCBs x250 40kA HNB60U Description Breaking capacity Icu: 40 ka (400/45V AC) Ics: 20 ka Adjustable thermal x In Adjustable magnetic x In (60/200A) x In (250A) 4P neutral setting: 0 or 00% Cat ref. Cat ref. In 3P 4P 60A HNB60U HNB6U 200A HNB200U HNB20U 250A HNB250U HNB25U 02 Subject to technical modification / New Ended Replacement

13 MCCBs x250 - accessories Indication contacts - changeover switch (ON/OFF): indicates the position of the MCCB is open or closed. - changeover alarm contact: indicates MCCB tripping. Coil connection - Connection capacity: 0.75mm 2 flexible or rigid cables - Optional connection cables. The cable capacity of the terminals is 0.5 to.25mm 2. Shunt trip - Remote tripping of MCCBs or trip-free switches. Operating voltage: 0.7 to. x Un. Under voltage release - Allows the tripping of MCCBs when voltage level drops between 35 and 70% of Un. - Pick up voltage 0.85 x Un. Direct rotary handle - Padlockable - Equipped with front cover and handle - Fixing without any additional screw. Extended rotary handle - IP55 - Supplied complete with shaft and handle. Technical information: Page 27 Accessories Description Characteristics Cat ref. Auxiliary contacts AX AL Shunt trips SH Undervoltage releases UV Direct rotary handles Padlockable Extended rotary handles Padlockable Padlocking device To mount on MCCBs for handle locking 3 padlocks changeover contact HXA02H 250V AC / 3A 25V DC / 0.4A NO + NC changeover alarm contact HXA024H 250V AC / 3A 25V DC / 0.4A NO + NC 24V DC HXA00H 48V DC HXA002H 00-20V AC HXA003H V AC HXA004H V AC HXA005H 24V DC HXA0H 00-20V AC HXA03H V AC HXA04H V AC HXA05H Max Ø 6mm HXB030H Max Ø 8mm 200mm Max Ø 8mm HXB03H HXA039H Motor operators 24V DC HXB040H V AC HXB042H HXA02H HXA004H HXA024H HXA04H HXB040H Accessories Cat ref. Cat ref. Description Characteristics 3P 4P Interlocking Wire type HXB065H HXB065H Collar terminals Set of 4 pieces HYB00H HYB002H Aluminium / copper conductors 50mm 2 rigid cables 85mm 2 flexible cables Extended connections For straight connections Set of 4 pieces HYB00H HYB00H For spreader connections Set of 4 pieces HYB0H HYB02H Rear connections Set of 3 pieces HYB03H HYB032H Interphase barriers Set of 3 HYB09H HYB09H Height: 97mm Terminal covers - 2 pcs For extended straight connections HYB02H HYB022H For extended spreader connections HYB023H HYB024H For rear connections HYB025H HYB026H For collar terminals HYB027H HYB028H HYB022H HYB024H HYB03H Subject to technical modification / New Ended Replacement 03

14 MCCBs h250 Moulded case circuit breakers h250-3p & 4P - Mechanical test button, sealable settings. - Comply with IEC Connection: Terminal area width 25 mm Electronic trip unit LSI: - Long delay (thermal equivalent) adjustable: Ir = 0.4 to x In - Short delay (magnetic equivalent) adjustable: 2.5 to 0 x Ir - Time delay: s Technical information: Page 33 *Please check availability with your local Hager sales office at time of order HNC250H MCCBs h250 50kA LSI Description - Breaking capacity Icu: 50 ka (400/45V AC) Ics: 25 ka - Adjustable thermal Ir = 0.4 to x In - Adjustable magnetic 2.5 to 0 x Ir Cat ref. Cat ref. Characteristics 3P 4P* 40A HNC040H HNC04H 25A HNC25H HNC26H 250A HNC250H HNC25H MCCBs h250 70kA LSI HEC250H Description - Breaking capacity Icu: 70 ka (400/45V AC) Ics: 70 ka - Adjustable thermal Ir = 0.4 to x In - Adjustable magnetic 2.5 to 0 x Ir Cat ref. Cat ref. Characteristics 3P 4P* 40A HEC040H HEC04H 25A HEC25H HEC26H 250A HEC250H HEC25H 04 Subject to technical modification / New Ended Replacement

15 MCCBs h250 - accessories Indication contacts - changeover switch (ON/OFF): indicates the position of the MCCB is open or closed. - changeover alarm contact: indicates MCCB tripping. Coil connection - Connection capacity: 0.75mm 2 flexible or rigid cables - Optional connection cables. The cable capacity of the terminals is 0.5 to.25mm 2. Shunt trip - Remote tripping of MCCBs or trip-free switches. Operating voltage: 0.7 to. x Un. Under voltage release - Allows the tripping of MCCBs when voltage level drops between 35 and 70% of Un. - Pick up voltage 0.85 x Un. Direct rotary handle - Padlockable - Equipped with front cover and handle - Fixing without any additional screw. Extended rotary handle - IP55 - Supplied complete with shaft and handle. Technical information: Page 37 Accessories Description Characteristics Cat ref. Auxiliary contacts AX AL Shunt trips SH Undervoltage releases UV Direct rotary handles Padlockable Extended rotary handles Padlockable Padlocking device To mount on MCCBs for handle locking 3 padlocks changeover contact 250V AC / 3A 25V DC / 0,4A NO + NC changeover alarm contact 250V AC / 3A 25V DC / 0,4A NO + NC 24V DC HXC02H HXC024H HXC00H 48V DC HXC002H 00-20V AC HXC003H V AC HXC004H V AC HXC005H 24V DC HXC0H 00-20V AC HXC03H V AC HXC04H V AC HXC05H Ø 5-8mm 2 max HXC030H Ø 5-8mm 2 max 320mm Max Ø 5mm HXC03H HXC039H HXC02H HXC004H HXC024H HXC04H Motor operators 24V DC HXC040H V AC HXC042H Interlocking Wire type HXC065H HXC039H Accessories Cat ref. Description Characteristics 3P 4P Collar terminals - copper Set of 3 or 4 HYC003H HYC004H Extended connections Straight connections - set of 4 HYC00H HYC00H Spreader connections - set of 3 or 4 HYC0H HYC02H Rear connections Set of 3 or 4 HYC03H HYC032H Interphase barriers Set of 3 HYC09H HYC09H Height: 97mm Terminal covers - 2 pcs For extended straight connections HYC02H HYC022H For rear connections HYC025H HYC026H For collar terminals HYC027H HYC028H HYC0H HYC03H Subject to technical modification / New Ended Replacement 05

16 MCCBs h630 Moulded case circuit breakers h630-3p & 4P - Adjustable neutral 0-50% - 00% - Mechanical test button, lockable settings - Comply with IEC Connection: - Directly on copper cable terminal, with end lug max. width: 30mm Electronic trip unit LSI: - Long delay (thermal equivalent) adjustable: Ir = 0.4 to x In - Short delay (magnetic equivalent) adjustable: 2.5 to 0 x Ir (400A) 2.5 to 8 x Ir (630A) - Time delay: s Technical information: Page 42 *Please check availability with your local Hager sales office at time of order HND630H MCCBs h630 50kA LSI Description - Breaking capacity Icu: 50 ka (400/45V AC) Ics: 50 ka - Adjustable thermal Ir = 0.4 to x In - Adjustable magnetic 2.5 to 0 x Ir (400A) 2.5 to 8 x Ir (630A) - Time delay: s Cat ref. Cat ref. In 3P 4P* 400A HND400H HND40H 630A HND630H HND63H MCCBs h630 70kA LSI HED630H Description - Breaking capacity Icu: 70 ka (400/45V AC) Ics: 50 ka - Adjustable thermal Ir = 0.4 to x In - Adjustable magnetic 2.5 to 0 x Ir (400A) 2.5 to 8 x Ir (630A) - Time delay: s Cat ref. Cat ref. In 3P 4P* 400A HED400H HED40H 630A HED630H HED63H 06 Subject to technical modification / New Ended Replacement

17 MCCBs h630 - accessories Indication contacts - changeover switch (ON/OFF): indicates the position of the MCCB is open or closed. - changeover alarm contact: indicates MCCB tripping. Coil connection - Connection capacity: 0.75mm 2 flexible or rigid cables - Optional connection cables. The cable capacity of the terminals is 0.5 to.25mm 2. Shunt trip - Remote tripping of MCCBs. Operating voltage: 0.7 to. x Un. Under voltage release - Allows the tripping of MCCBs when voltage level drops between 35 and 70% of Un. - Pick up voltage 0.85 x Un. Direct rotary handle - Padlockable - Equipped with front cover and handle - Fixing without any additional screw. Extended rotary handle - IP55 - Supplied complete with shaft and handle. Technical information: Page 46 Accessories Description Characteristics Cat ref. Auxiliary contacts AX AL changeover contact 250V AC / 3A 25V DC / 0,4A NO + NC HXC02H changeover alarm contact 250V AC / 3A 25V DC / 0,4A NO + NC HXC024H HXC02H HXC04H Shunt trips 24V DC HXC00H SH 48V DC HXC002H 00-20V AC HXC003H V AC HXC004H V AC HXC005H Undervoltage releases UV 24V DC HXC0H 00-20V AC HXC03H V AC HXC04H V AC HXC05H Direct rotary handles Max Ø 6 mm HXD030H Padlockable Extended rotary handles Max Ø 8mm HXD03H Padlockable 320mm Padlocking device To mount on MCCBs for handle locking 3 padlocks Max Ø 8mm HXD039H HXD030H HXD039H Accessories Cat ref. Cat ref. Description Characteristics In 3P 4P Motor operators 24-48V DC HXD040H HXD040H V AC HXD042H HXD042H Interlocking HXD065H HXD065H Wire type Collar terminals Set of 3 or A HYD003H HYD004H Terminals for copper conductors x mm 2 Terminals for multiple aluminium/ Set of 3 or A HYD007H HYD008H copper conductors 2 x mm 2 Extended connections Set of 4 400A HYD00H HYD00H For straight connections 630A HYD03H HYD03H For spreader connections Set of 3 or 4 400A HYD0H HYD02H 630A HYD04H HYD05H Rear connections Set of 3 or 4 400A HYD03H HYD032H 630A HYD033H HYD034H Interphase barriers Set of 3 HYD09H HYD09H Height: 97mm Terminal covers - 2 pcs For extended straight connections HYD02H HYD022H For extended spreader connections HYD023H HYD024H For rear connections HYD025H HYD026H For collar terminals HYD027H HYD028H HXD042H HYD003H HYD05H Subject to technical modification / New Ended Replacement 07

18 MCCBs h000 Moulded case circuit breakers h000-3p & 4P - Adjustable neutral 0-50% - 00% - Mechanical test button, lockable settings. Connection: - Direct on copper terminal, with end lug max. width: 50mm - Comply with IEC Electronic trip unit LSI: - Long delay (thermal equivalent) adjustable: Ir= 0,4 to x In - Short delay (magnetic equivalent) adjustable: 2,5 to 0 x Ir ( A) 2.5 to 8 x Ir (000A) - Time delay: s Technical information: Page 50 *Please check availability with your local Hager sales office at time of order MCCBs h000 50kA LSI Cat ref. Cat ref. HNE970H Description - Breaking capacity Icu: 50 ka (400/45V AC) Ics: 50 ka - Adjustable thermal Ir = 0,4 to x In - Adjustable magnetic 2,5 to 0 x Ir (800A) 2,5 to 8 x Ir (000A) - Time delay: s - Neutral setting from 0-50 to 00% In 3P 4P* 800A HNE800H HNE80H 000A HNE970H HNE97H MCCBs h000 70kA LSI Cat ref. Cat ref. HEE80H Description - Breaking capacity Icu: 70 ka (400/45V AC) Ics: 50 ka - Adjustable thermal Ir = 0,4 to x In - Adjustable magnetic 2,5 to 0 x Ir (800A) 2,5 to 8 x Ir (000A) - Time delay: 0,-0,2s - Neutral setting from 0-50 to 00% In 3P 4P* 800A HEE800H HEE80H 000A HEE970H HEE97H 08 Subject to technical modification / New Ended Replacement

19 MCCBs h000 - accessories Indication contacts - changeover switch (ON/OFF): indicates the position of the MCCB is open or closed. - changeover alarm contact: indicates MCCB tripping. Coil connection - Connection capacity: 0.75mm 2 flexible or rigid cables - Optional connection cables. The cable capacity of the terminals is 0.5 to.25mm 2. Shunt trip - Remote tripping of MCCBs. Operating voltage: 0.7 to. x Un. Under voltage release - Allows the tripping of MCCBs when voltage level drops between 35 and 70% of Un. - Pick up voltage 0.85 x Un. Direct rotary handle - Padlockable - Equipped with front cover and handle - Fixing without any additional screw. Extended rotary handle - IP55 - Supplied complete with shaft and handle. Technical information: Page 54 Accessories Description Characteristics Cat ref. Auxiliary contacts AX AL Shunt trips SH Undervoltage releases UV Direct rotary handle Padlockable Extended rotary handles Padlockable Padlocking device To mount on MCCB for handle locking 3 padlocks changeover contact 250V AC / 3A 25V DC / 0,4A NO + NC changeover alarm contact 250V AC / 3A 25V DC / 0,4A NO + NC 24V DC HXC02H HXC024H HXC00H 48V DC HXC002H 00-20V AC HXC003H V AC HXC004H V AC HXC005H 24V DC HXE0H 00-20V AC HXE03H V AC HXE04H V AC HXE05H HXE030H Max Ø 8mm 320mm Max Ø 8 mm HXE03H HXD039H Motor operators 24-48V DC HXE040H V AC HXE042H Interlocking Wire type HXE065H HXC02H HXC004H HXC024H HXE04H HXD039H Accessories Cat ref. Cat ref. Description In 3P 4P* Terminal covers - 2 pcs For extended connections HYE02H HYE022H For rear connections HYE025H HYE026H Rear connections Set of 3 or 4 800A HYE03H HYE032H 000A HYE033H HYE034H HYE03H Subject to technical modification / New Ended Replacement 09

20 MCCBs h600 Moulded case circuit breakers h600-3 pole - 3 trip units 4 pole - 4 trip units - Adjustable neutral 0-50% - 00% - Mechanical test button, lockable settings. - Comply with IEC Electronic trip unit LSI: - Long delay (thermal equivalent) adjustable: Ir = 0.4 to x In - Short delay (magnetic equivalent) adjustable: 2.5 to 0 x Ir - Time delay: Connection: - Directly on copper cable terminal, with end lug max. width: 60mm Technical information: Page 59 *Please check availability with your local Hager sales office at time of order HNF990H MCCBs h600 50kA LSI Description - Breaking capacity Icu: 50 ka (400/45V AC) Ics: 50 ka - Adjustable thermal Ir = 0.4 to x In - Adjustable magnetic 2.5 to 0 x Ir - Time delay: s - Neutral setting 0, 50, 00% Cat ref. Cat ref. In 3P 4P* 250A HNF980H HNF98H 600A HNF990H HNF99H HEF980H MCCBs h600 70kA LSI Description - Breaking capacity Icu: 70 ka (400/45V AC) Ics: 50 ka - Adjustable thermal Ir = 0.4 to x In - Adjustable magnetic 2.5 to 0 x Ir - Time delay: s - Neutral setting from 0, 50, 00% Cat ref. Cat ref. In 3P 4P* 250A HEF980H HEF98H 600A HEF990H HEF99H 0 Subject to technical modification / New Ended Replacement

21 MCCBs h600 - accessories Indication contacts - changeover switch (ON/OFF): indicates the position of the MCCB is open or closed. - changeover alarm contact: indicates MCCB tripping. Coil connection - Connection capacity: 0.75mm 2 flexible or rigid cables - Optional connection cables. The cable capacity of the terminals is 0.5 to.25mm 2. Shunt trip - Remote tripping of MCCBs. Operating voltage: 0.7 to. x Un. Under voltage release - Allows the tripping of MCCBs when voltage level drops between 35 and 70% of Un. - Pick up voltage 0.85 x Un. Direct rotary handle - Padlockable - Equipped with front cover and handle - Fixing without any additional screw. Extended rotary handle - IP55 - Supplied complete with shaft and handle. - Rear connection included Technical information: Page 62 Accessories Description Characteristics Cat ref. Auxiliary contacts AX AL Shunt trips SH Undervoltage releases UV Direct rotary handles Padlockable Extended rotary handles Padlockable Padlocking device To mount on MCCBs for handle locking 3 padlocks changeover contact 250V AC / 3A 25V DC / 0,4A NO + NC changeover alarm contact 250V AC / 3A 25V DC / 0,4A NO + NC 24V DC HXC02H HXC024H HXF00H 48V DC HXF002H 00-20V AC HXF003H V AC HXF004H V AC HXF005H 24V DC HXE0H 00-20V AC HXE03H V AC HXE04H V AC HXE05H Max Ø 8mm HXF030H Max Ø 8mm 320mm Max Ø 8mm HXF03H HXF039H Motor operators 24V DC HXF040H V AC HXF042H HXC02H HXF004H HXC024H HXE04H HXF040H Subject to technical modification / New Ended Replacement

22 DIN NH fuses and fuse carriers Fuse carriers description Size according to DIN from 000 to 2 to suit fuses according to AS/NZS60269 Connection capacity mm Fuse description DIN fuses with a breaking capacity up to 20kA at 500V - Class gg - IEC sizes from 000 to 2 Technical information Page 73 Fuse switch disconnectors Description Suits 3 x size 00 60A DIN blade fuses Suits3 x size 250A DIN blade fuses Suits 3 x size 2 400A DIN blade fuses Cat ref. LT052 LT50 LT250 LT50 Cable clamps Description Suitable for LT052 (6-70mm 2 ) Suitable for LT50 (70-50mm 2 ) Suitable for LT250 (20-240mm 2 ) Cat ref. LZ05 LZ5 LZ52 NH Fuses LNH0080M LNH260M Description Current rating (A) Cat ref. Size A LNH0050M 63A LNH0063M 80A LNH0080M 00A LNH000M Size 00 25A LNH025M 60A LNH060M Size 00A LNH00M 25A LNH25M 60A LNH60M 200A LNH200M 250A LNH250M Size 2 60A LNH260M 200A LNH2200M 250A LNH2250M 35A LNH235M 400A LNH2400M 2 Subject to technical modification / New Ended Replacement

23 Load break switches - DIN or screw mount Description The HA series is a range of multipole load disconnector switches with manual operation. They enable making and breaking on load and safety isolation of any low voltage installation. Technical data - Visualised breaking - Double breaking per phase - 3 or 4 pole - Padlockable handle - Auxiliary contacts - Rotary handles - Extension shafts - Complying with IEC For replacement parts, please contact customer service on Technical information Page 75 *Please check availability with your local Hager sales office at time of order Load break switches - DIN or screw mount Description Width Characteristics Module mm Cat ref. 3 pole 400V~ 6 mod In 80A 08 HA304 6 mod In 00A 08 HA305 6 mod In 25A 08 HA mod In 60A 42 HA mod In 200A 42 HA mod In 250A 42 HA309M 4 pole 400V~ 6 mod In 25A 08 HA mod In 200A 42 HA408 HA305 Accessories Description Characteristics Cat ref. Auxiliary contacts NC + NO HZ022 Terminal shrouds To suit HA307/HA308/HA408 mod HZ062 Switch line or load side (Cable lug connection) To suit HA307/HA308 mod HZ072 Switch line or load side c/- cable clamp Interlocked handle - Black IP55 80 to 250A HZC00 for use with extension shaft NOTE: does not replace rotary handle Extension shaft - 200mm 80 to 250A HZC03 HZC00 HZC03 HZ022 HZC062 HZC072 Subject to technical modification / New Ended Replacement 3

24 Load break switches - Screw mount only Description The HA series is a range of multipole load disconnector switches with manual operation. They enable making and breaking on load and safety isolation of any low voltage installation. Fiberglass reinforced polyester case, self extinguishable, resists creepage distance and arc, tropicalised. Technical data - Ith (40 ): 250 to 600A - Un 400 / 690V AC - Visualised breaking - Double breaking per phase - 3 or 4 pole - Padlockable handle - Auxiliary contacts - Complying with IEC Note: Handle and shaft must be ordered separately. For replacement parts, please contact customer service on Technical information Page 75 *Please check availability with your local Hager sales office at time of order Load break switches - screw mount only HA354 Description Characteristics Cat ref. 3 pole 400V~ In 250A HA354 In 400A HA356 In 630A HA358 In 800A HA360 In 250A HA362 In 600A HA364 4 pole 400V~ In 400A - AC23 HA457 In 630A - AC23 HA458 Accessories HZC003 HZC06 Description Characteristics Modules Cat ref. Auxiliary contacts 25 to 600A HZ023 NO + NC AC, 5A, 250V Terminal shrouds - 3 pcs To suit HA354 mod HZC203 Switch line or load side To suit HA356/HA358/ mod HZC205 Switch line or load side Interlocked handle - Black IP55 00 to 630A HZC002 for use with extension shaft 800 to 600A NOTE: does not replace rotary handle HZC003 Extension Shaft 00 to 630A HZC02-320mm 800 to 600A HZC06 HZ023 HZC203 4 Subject to technical modification / New Ended Replacement

25 Manual Transfer Switches Description Manual transfer switches allow manual switching, changeover switching or ON load power circuit permutation. For safety breaking. - 4 pole - Mounting on perforated plates or crossbars. - Lockable in position: I, O or II HI452, HI454 and HI456 can be mounted in quadro M distribution boards. Complies with EN Connection with terminals For replacement parts, please contact customer service on Technical information: Page 76 *Please check availability with your local Hager sales office at time of order Manual transfer switches Description In/A Cat ref. 4 pole 60 HI452* Non-modular design 250 HI454* 400 HI456* 630 HI458* 800 HI460* 250 HI462* 600 HI464* HI452 Manual transfer switch accessories Description Characteristics Cat ref. Interlocked handle 60 to 630A HZI002* for use with extension shaft - 3 positions: 0-I-II 800 to 600A HZI003* - Locked with 3 padlocks NOTE: does not replace rotary handle Extension Shaft 60 to 630A HZC02-320mm 800 to 600A HZC06 Auxiliary contacts 25 to 600A, NO + NC HZ60* Terminal shrouds 4P In/A: 25 to 200A HZC202* 4P In/A: 200 to 400A HZC204* 4P In/A: 400 to 630A HZC206* Terminal covers for switches 250 to 400A HZI202* for switches 630A HZI203* for switches 800 to 250A HZI204* for switches 600A HZI205* Busbars for switches 250A HZ57* for switches 400A HZ58* for switches 630A HZ59* for switches 800 to 000A HZ62* for switches 250A HZ63* for switches 600A HZ64* HZI002 HZC02 HZ60 HZC202 Subject to technical modification / New Ended Replacement 5

26 Automatic Transfer Switches Description Automatic transfer switches allow automatic switching, changeover switching or ON load power circuit permutation. For safety breaking. - 4 pole - Mounting on plain or perforated plates. - Lockable in position: O Complies with EN Connection with terminals For replacement parts, please contact customer service on Technical information: Page 78 *Please check availability with your local Hager sales office at time of order HIC425G Automatic transfer switches Description 4 pole - 3 positions: 0-I-II In/A Cat. ref. w/o autom. transf. relay Cat. ref. with autom. transf. relay Cat. ref. with energy mngmt. 25 HIB42M* HIC42G* HIC42E* 60 HIB46M* HIC46G* HIC46E* 200 HIB420M* HIC420G* HIC420E* 250 HIB425M* HIC425G* HIC425E* 400 HIB440M* HIC440G* HIC440E* 630 HIB463M* HIC463G* HIC463E* 800 HIB480M* HIC480G* HIC480E* 000 HIB490M* HIC490G* HIC490E* 250 HIB49M* HIC49G* HIC49E* 600 HIB492M* HIC492G* HIC492E* Automatic transfer switch accessories HZC002 HZI9 Description Characteristics Cat ref. Terminal shrouds 4P In/A: 25 to 200A HZC202* 4P In/A: 200 to 400A HZC204* 4P In/A: 400 to 630A HZC206* Remote interfaces changeover status display HZI90* changeover status and control display HZI9* Terminal covers for switches 250 to 400A HZI202* for switches 630A HZI203* for switches 800 to 250A HZI204* for switches 600A HZI205* Busbars for switches 250A HZ57* for switches 400A HZ58* for switches 630A HZ59* for switches 800 to 000A HZ62* for switches 250A HZ63* for switches 600A HZ64* HZI205 HZ59 6 Subject to technical modification / New Ended Replacement

27 Fuse combination switches with handle Functions The HFD Series of Hager isolators are manually operated multipolar fuse combination switches. They break or switch OFF/ON load and provide safety isolation with protection against over current for any low voltage electrical circuit. - Double break by phase (top and bottom of fuse) - Protection against overcurrent by fuse circuit-breakers with high breaking capacity (00kA eff.) - IP2 protection with terminal shrouds - Compact - TEST position for testing control circuits without power using U type auxiliary contacts. Complies with standards - IEC IEC IEC EN DIN VDE VDE 0660 Part 07 Note: Interlocked handle and shaft must be ordered separately. For replacement parts, please contact customer service on *Please check availability with your local Hager sales office at time of order Fuse combination switches Description In/A Fuse sizes Length Modules (7.5mm) Cat ref. 3 pole 400V~ min. 24 HFD32* min. 24 HFD36* min. 72 HFD325* min. 72 HFD340* HFD32 Fuse combination switch accessories Description Characteristics Cat ref. Interlocked handle - Black IP55 25 to 400A HZC002* for use with extension shaft NOTE: does not replace rotary handle Extension Shaft 25 to 400A HZC02* - 320mm Auxiliary contacts NO HZF30* - suitable for switches 25 to 400A NC HZF302* Terminal shrouds 3P In/A: 00 to 60A HZF202* 3P In/A: 250 to 400A HZF204* HZC002 HZC02 HZF30 HZF204 Subject to technical modification / New Ended Replacement 7

28 Earth leakage relays & toroids Description This range of earth leakage relays were designed on an electronic basis, which ensure the monitoring of earth fault currents. When the fault current rises above the selected level, the outputs of the relay operate & depending on the relay selected, it can have both adjustable sensitivity and time delay that can provide selectivity/discrimination. The relays are linked with detection toroids. Common characteristics - Standard DIN EN , IEC60755, IEC Fixed & adjustable devices - Positive safety: the relay trips in the event of a break in the connection between relay & toroid. - Positive / local reset required after a fault is detected. - Protected against nuisance tripping - Class A - Output: c/o contact 250V~ 6A AC - Visual display of fault - Supply voltage 230V +/- 20% 50/60Hz Connection capacity - Flexible - to 2.5mm - Stranded/rigid -.5 to 4mm Premium features - Adjustable sensitivity & time delay (sealable) - Display of fault current prior to triggering relay (5%-75%) - Extra output contact (250V-AC/6A) to enable remote indication of fault currents above 50% of Irn - Remote test and reset by three wire link Technical information Page 80 Earth leakage relays HR50 HR520 Description Width Cat ref. Without delay mod HR502 c/o contact 250V 6A ~ AC Fixed sensitivity = 300mA Trips immediately Standard 3 mod HR50 c/o contact 250V 6A ~ AC Adjustable sensitivity Irn= 0.03/0./0.3/0.5//3/0A Adjustable time delay rt= 0/0./0.3/0.4/0.5//3sec Premium 3 mod HR520 c/o contact 250V 6A ~ AC Fail safe contact 250V 6A ~ AC Pre-alarm contact 250V 6A ~ AC Adjustable sensitivity Irn= 0.03/0./0.3/0.5//3/0A Adjustable time delay rt= 0/0./0.3/0.4/0.5//3sec Bargraph = 5% - 75% Irn Integral toroid c/o contact 250V 6A ~ AC Adjustable sensitivity Irn= 0.03/0./0.3/0.5//3A Adjustable time delay rt= 0/0./0.3/0.5/0.75/sec Ø of toroid: 35mm 6 mod HR44 Circular section toroids HR700 Characteristics Inside Ø of toroid: 30mm Inside Ø of toroid: 35mm Inside Ø of toroid: 70mm Inside Ø of toroid: 05mm Inside Ø of toroid: 40mm Cat ref. HR700 HR70 HR702 HR703 HR704 8 Subject to technical modification / New Ended Replacement

29 MCCBs x60 - Settings and adjustments MCCBs x60 TM 220/240V AC IEC /45V AC IEC HHA Icu 35 ka 25 ka Ics 25 ka 20 ka HNA Icu 85 ka 40 ka Ics 40 ka 20 ka PUSH TO TRIP Magnetic and thermal settings â ê Ir (x In) TRIP ô 6 TM - Thermal magnetic setting In 6-50 A A A 60 A Imag 600 A 000 A 500 A 600 A Magnetic adjustment fixed > 0 x In Thermal adjustment from 0.63 to x In Subject to technical modification 9

30 MCCBs x60 - Settings and adjustments Tripping curve MCCB x Instantaneous trip current : 6A to 50A : 600A +/- 20A 63A to 80A : 000A +/- 200A 00 A to 25A : 500A +/- 300A 60A : 600A +/- 320A Tripping time (sec) From cold state 0 60A 25A, 50A 80A 00A, 40A 63A 32A 25A 20A 6A From warm state (rated current) 0. The magnetic thereshold tripping curves is mean value. The tripping area is Irm ±20%. 0.0 Thermal constraint curve at 45A (Let-through energy) MCCB x Current limiting curve at 45A (Let-through peak current) MCCB x I 2 2 t (A s) 0 6 HHA...up to 25kA HNA...up to 40kA 60A 25A 00A 80A 63A 50A 40A 32A A Ip (ka) 0 HHA...up to 25kA HNA...up to 40kA A 25 A 00 A A 50 A 32 A 40 A 25 A Iccp (ka rms) Iccp (ka rms) Subject to technical modification

31 MCCBs x60 - Dimensions and characteristics Dimensions MCCB x60 A B 96. A B C P P P C 45 4P Terminal covers for extended straight connections A C A B C P B 2P P P Terminal cover for extended spreader connections A 60.5 A B C B 3P P Subject to technical modification 2

32 AI MCCBs x60 - Dimensions and characteristics Connection Connection with end lugs min. 6 o max.70 o min. 6 o max.95 o 6mm max 64 6Nm 2 % noir 6 mm Max. PUSH TO TRIP min. 6 o max. 50 o 5 85 min. 35 o 35 o to 50 o = 25Nm 60 o to 85 o = 25Nm max. 85 o 2 % noir Interphase barriers L PUSH TO TRIP HYA09H 50 Ech. 40% Ech. 60% 55 PUSH TO TRIP L Ech. 60% AI_H60_T_3 22 Subject to technical modification

33 MCCBs x60 - Dimensions and characteristics Extended straight connections 7 3P 28 Ø mm 92 6 Nm 4P Extended spreader connections Ø 8 3P Ø Nm mm PUSH TO TRIP 4P Direct rotary handle (3 P) 74.5 (4 P) Extended rotary handle (3 P) 74.5 (4 P) Subject to technical modification 23

34 MCCBs x60 - Dimensions and characteristics Auxiliaries Auxiliaries for MCCBs TRIP PUSH TO TRIP Mounting combination for auxiliaries and releases AX Auxiliary contact 4 P 3 P SH Shunt trip AX AL SH / UV AL Alarm contact UV Undervoltage release 24 Subject to technical modification

35 MCCBs x250 - Settings and adjustments MCCBs x250 TM 220/240V AC IEC /45V AC IEC HNB Icu 85 ka 40 ka Ics 40 ka 20 ka PUSH TO TRIP Magnetic and thermal settings â ê 6 TRIP PUSH TO TRIP l i (xin) 0,8 0,63 l r (xin) 6 Thermal adjustment from 0.63 to x In Magnetic adjustment from 6 to 3 x In (00-200A) from 5 to x In (250A) TM - Thermal magnetic setting A 250A Ir (x In) â x In Ii (x In) ê x In x In x In/Ii ô 0-00% %0 Ech. 50% 00% xin / Ii 3 0 l i (xin) 0.63 l r (xin) ô ê â Ech. 80 % Subject to technical modification 25

36 MCCBs x250 - Settings and adjustments Tripping curve MCCB x Instantaneous trip current : 00A : 300A +/- 260A 25A : 625A +/- 325A 60A : 2080A +/- 46A 200A : 2600A +/- 520A 225A : 2925A +/- 585A 250A : /- 550A 000 From cold state Tripping me (sec) 00 0 From hot state x In(A) Thermal constraint curve at 45V (Let-through energy) MCCB x A Current limiting curve at 45V (Let-through peak current) MCCB x A HNB...up to 40kA 0.3 I 2 2 t (A s) Ip (ka) Iccp (ka rms) Iccp (ka rms) Subject to technical modification

37 MCCBs x250 - Dimensions and characteristics Dimensions MCCB x (3 P) 40 (4 P) PUSH TO TRIP Terminal covers for extended straight connections A C A B C 3P P B PUSH TO TRIP Subject to technical modification 27

38 MCCBs x250 - Dimensions and characteristics Accessories Terminal cover for extended spreader connections A 64 A B C 3P B 4P PUSH TO TRIP Terminal cover for rear connections B A C A B C 3P P PUSH TO TRIP Terminal covers for collar terminals A C A B C B 3P P Subject to technical modification

39 MCCBs x250 - Dimensions and characteristics Connection Extended straight and spreader connections 23 6 mm Max. 23 Ø Nm 65 2 Nm PUSH TO TRIP PUSH TO TRIP PUSH TO TRIP Ø.5 3P Ø 3P Ø Ech. 60% P P Rear connections 4P Ech. 27% 3P mm AI_H60_T_3 AI_H60_T_3 92 Subject to technical modification 29

40 MCCBs x250 - Dimensions and characteristics Connection by collar 20mm max,9,7,9, mm Max. Connection with end lugs Ø mm max.,9,9,7, mm max Nm 3,7 3, L L H 5540.a min. 35 o max. 50 o 5 3,7 85 3,7 min. 35 o max. 85 o 35 o to 50 o = 25Nm 60 o to 85 o 2 % noir 55 = 25Nm PUSH TO TRIP Ech. 60% PUSH TO TRIP PUSH TO TRIP Interphase barriers AI_H60_T_3 30 Subject to technical modification

41 MCCBs x250 - Dimensions and characteristics Accessories Rotary handle (3P/4P) PUSH TO TRIP Extended rotary handle 2 (3P/4P) PUSH TO TRIP Motor operator Rated operating voltage Operating current (A) Starting current (A) Operating method Operating time (s) Operating switch rating Power supply required Dielectric properties (min) 24V DC HXB040H V AC HXB042H 24V DC V AC 4 24V DC V AC 8 direct drive ON 0. OFF 0. RESET 0. 00V, 0.A, opening voltage 44V, current 4mA 300 VA minimum 24V DC 000 V AC V AC 500 V AC Subject to technical modification 3

42 MCCBs x250 - Dimensions and characteristics Auxiliaries Auxiliaries for MCCBs 6 TRIP PUSH TO TRIP Mounting combination for auxiliaries and releases AX Auxiliary contact 4 P 3 P SH Shunt trip AX AX AL SH / UV AL Alarm contact UV Undervoltage release 32 Subject to technical modification

43 MCCBs h250 - Settings and adjustments MCCBs h250 LSI HNC 220/240 V AC (ka) 380/45 V AC (ka) 660/690 V AC (ka) Icu Ics HEC Icu Ics Electronic trip unit setting (LSI) Characteristics (*) Use 3P 4P Generator protection pos. pos., 4 and 7 Standard protection pos. 2 and 3 pos. 2, 5 and 8 Motor protection pos. 4 and 5 pos. 3, 6 and 9 L - Long delay - protection against overloads: Ir and tr settings S - Short delay - protection against short circuits: Isd and tsd settings I - Instantaneous - max. instantaneous threshold (< 0 ms) in case of short circuit: 2.5 to 0 x Ir. T Ir adjustable xin IR (A) Ir (A) Characteristics x Ir I PICK UP Subject to technical modification 33

44 MCCBs h250 - Settings and adjustments MCCB h250 3P LSI Tripping time (s) , 2, 3, x Ir(A) LSI 250A 2 (3P) LSI â Ir (x In) ê Characteristics 3P In A 250A Long time delay Short time delay Inst NP Ir (x In) tr, tn (s) Isd (xir) tsd (s) Ii (xir) In (x In) 0.4 ok 0.5 ok 0.63 ok 0.8 ok 0.85 ok 0.9 ok 0.95 ok ok s at 2 xir s at 2 xir 0. 4 (max x In) 4 5s at 6 xir s at 6 xir Subject to technical modification

45 MCCBs h250 - Settings and adjustments MCCB h250 4P LSI Tripping time (s) 0, 4, 7 2, 5, 8 3, 6, x Ir(A) LSI 250A 2 (4P) LSI â Ir (x In) ê Characteristics 4P In A 250A Long time delay Short time delay Inst NP Ir (x In) tr, tn (s) Isd (xir) tsd (s) Ii (xir) In (x In) 0.4 ok 0.5 ok 0.63 ok 0.8 ok 0.85 ok 0.9 ok 0.95 ok ok s at 2 xir s at 2 xir 5 0% 3 7.5s at 6 xir s at 2 xir s at 2 xir s at 6 xir s at 2 xir s at 2 xir s at 6 xir (max 3 x In) 50% 00% Subject to technical modification 35

46 MCCBs h250 - Settings and adjustments Thermal constraint curve at 45V (Let-through energy) MCCB h I 2 2 t (A s) 0 6 HNC... up to 50kA HEC... up to 70kA Iccp (ka rms) Current limiting curve at 45V (Let-through peak current) MCCB h Ip (ka) HNC... up to 50kA HEC... up to 70kA Iccp (ka rms) Subject to technical modification

47 MCCBs h250 - Dimensions and characteristics Dimensions MCCBs A 25.5 A 3P 05 4P 40 PUSH TO TRIP A 3P 05 4P 40 Terminal cover for rear connections 7.5 A 96 A 3P 05 4P Accessories Terminal covers for extended straight connections A Subject to technical modification 37

48 MCCBs h250 - Dimensions and characteristics Connection Extended straight and spreader connections P Ø Nm Connection with end lugs Ø Nm Connection by collar â ê 20 max. 6 mm Max. 9 Nm min. 35 mm 2 max. 20 mm min. 35 mm 2 max. 20 mm 2 9 Nm 2 % noir PUSH TO TRIP 38 Subject to technical modification

49 MCCBs h250 - Dimensions and characteristics Rear connections 4P 3P Nm Accessories Direct rotary handle Subject to technical modification 39

50 MCCBs h250 - Dimensions and characteristics Extended rotary handle x Motor operator Rated operating voltage Operating current (A) Starting current (A) Operating method Operating time (s) Operating switch rating Power supply required Dielectric properties 24V DC HXC040H V AC HXC042H 24V DC V AC 4 24V DC V AC 8 direct drive ON 0. OFF 0. RESET 0. 00V, 0.A, opening voltage 44V, current 4mA 300 VA minimum 24V DC 000 V AC V AC 500 V AC 40 Subject to technical modification

51 MCCBs h250 - Dimensions and characteristics Auxiliaries Auxiliaries for MCCBs 6 TRIP Mounting combination for auxiliaries and releases AX Auxiliary contact 4 P 3 P SH Shunt trip AX AL SH / UV UV Undervoltage release AL Alarm contact Subject to technical modification 4

52 MCCBs h630 - Settings and adjustments MCCBs h630 LSI HND HED 220/240 V AC (ka) 380/45 V AC (ka) 660/690 V AC (ka) Icu Ics Icu Ics Electronic trip unit setting (LSI) T Ir adjustable A B ,6, S 0.S 3, x Ir I B2 Ir (A) Characteristics ON xir NP 2 3 L - Long delay - protection against overloads: Ir and tr settings S - Short delay - protection against short circuits: Isd and tsd settings I - Instantaneous - max. instantaneous threshold (< 0 ms) in case of short circuit: 2,5 to 0 x Ir (400A) and 2,5 to 8 x Ir (630A). PICK UP OFF 0.5xIR TEST IN â Long delay current Ir setting ê Other curve characteristics setting (tr, Isd, tsd) ô Neutral protection against overloads setting (*) Characteristic : use for generators protection. Characteristic 2 to 4 - standard protection: options allow coordination optimisation with other products. Characteristic 5 to 7 - motor protection: use positions according to motor starting characteristics. 42 Subject to technical modification

53 MCCBs h630 - Settings and adjustments Tripping curve MCCB h630 LSI (400A) Tripping time (s) , 7 7 5, 6 0., 2, 3, x Ir(A) Electronic trip unit setting (LSI) MCCB h630 LSI (400A) LSI â Ir (x In) ê Characteristics ô Neutral protection In A 400A Long time delay Short time delay Inst Ir (x In) tr, tn (s) Isd (xir) tsd (s) Ii (xir) 0.4 ok 0.5 ok 0.63 ok 0.8 ok ok 0.95 ok ok s at 2 xir s at 2 xir s at 6 xir 5 0s at 6 xir 6 9s at 6 xir 7 29s at 6 xir 0% 50% 00% (max 3 x In) Subject to technical modification 43

54 MCCBs h630 - Settings and adjustments Tripping curve MCCB h630 LSI (630A) Tripping time (s) , 6 0., 2, 3, x Ir(A) Electronic trip unit setting (LSI) MCCB h630 LSI (630A) LSI â Ir (x In) ê Characteristics ô Neutral protection In A 630A Long time delay Short time delay Inst Ir (x In) tr (s) Isd (xir) tsd (s) Ii (xir) 0.4 ok 0.5 ok 0.63 ok 0.8 ok ok 0.95 ok ok s at 2 xir s at 2 xir s at 6 xir 5 0s at 6 xir 6 6s at 6 xir 0% 50% 00% (max 3 x In) 44 Subject to technical modification