USER S MANUAL. Manual for Panel Mount Process Indicator. HTA INSTRUMENTATION (P) LTD. Your One Stop for Instrumentation, Calibration & Service

Size: px

Start display at page:

Download "USER S MANUAL. Manual for Panel Mount Process Indicator. HTA INSTRUMENTATION (P) LTD. Your One Stop for Instrumentation, Calibration & Service"

Shauna Young
6 years ago
Views:

Member of SN Registrars (Holdings) Ltd 8327 USER S MANUAL Manual for Panel Mount Process Indicator EQ-DS8B-IRRB EQ-DS8B-IRRB HTA INSTRUMENTATION (P) LTD.

1 Member of SN Registrars (Holdings) Ltd 8327 USER S MANUAL Manual for Panel Mount Process Indicator EQ-DS8B-IRRB EQ-DS8B-IRRB HTA INSTRUMENTATION (P) LTD. Your One Stop for Instrumentation, Calibration & Service # 73, Ramachandra Agrahara, Near T.R. Mills, Chamarajpet, Bangalore , INDIA Phone: , , Fax: Website : sales@htaipl.com ISO900:205 ISO 900:205 CERTIFIED Page - /

2 << Applications The Instrument can measure any range of Current or Voltage signal input. The user can select data remained or top value remained. The instrument can be use with 2 wire transmitter, Pressure Sensor, 4 wire weight Sensor and so on. For Nonlinear input, the instrument can process for 20 stages. As well the instrument can be with RS485 communication. The input, output and the power supply is isolated. Name of Parts 2. When used with Pressure sensor. The Instrument can supply DC2V auxiliary power & the sensor output is 2mV/V. Select input signal mv. 2 90~260V AC 6 3. When used with Ohm meter. Input 0-400Ù Select input signal rt. 8 24V+ 8 Gnd +mv 20 PV SV <</RST V(mV) AL Ù(ºC) AL2 V (ma)al3 << Malfunction Estimate:. No Display : Check all the connection & wiring if it is correct. Specially pay attention to the power supply terminals & signal input terminals, please do not wrong connect. As well pay attention to do not short the output terminals by strong current. 2. Wrong Display : Check it the PVF=0.00 Check if the input signal is conformity with the selected symbol. For RTD input, please use low impedance cable. The 3 wire should at the same length. 3. Wrong Control : When the instrument lost control, please check if the output diagram connection is correct. Or check if the components for output part damaged. 4. UUUU, LLLL : When the instrument displays "UUUU", it means the input signal exceeds the measured Usp range. When the instrument displays "LLLL", it means the input signal lower the measured Lsp range, or input signal terminal connection is Measured Value (PV) / Various Parameter Symbols Parameter Value / Rate Value / ct / AL Indication Lamps for Alarm V(mV) AL ON : Output OFF : No Alarm Indication Lamps for Alarm 2 Ù (ºC) AL2 ON : Output OFF : No Alarm Output Unit Indication Lamp / Alarm 3 (ma) Select / Confirm Key Shift / Clear / Reset Key Up Key Down Key 2 Page - 02/ V 9 20 R 90~260V AC 2 Page - /

3 Diagram Connections : * Please subject to the diagram on the product if any changes Application Examples. When used with 2 wire Transmitter. The Instrument can supply DC 24V auxiliary power, and isolate analogue output 4 ~ 20mA. Select input signal ma. 90~260V AC ~20mA +24V 8 24V ma 7 Gnd 8 Page -0/ Input Signal Specification: Input Signal Types A(AA/DA) ma V(AV/DV) mv Rt Pt TC Range 0~5A, 0~2A 0~mA, 0~0mA, 4~20mA 0~5V, 0~0V, 0~500V 0~0mV, ±00mV 0~400, 0~0K Cu50, Cu00, 50~50 C 200~650 C K : 0~320 C J : 0~300 C E : 0~000 C T : 50~400 C B : 0~820 C R : 0~700 C S : 0~600 C Input Impedance CT configurable K 2M 0.2mA 0.2mA 2M Factory Setting Indicate when order 4~20mA DC 0~0V 0~75mV 0~400 Indicate when order Pt00 High Voltage / Current Input or data remained function need special order. Al3 also can be use as analogue output, but you can select only one of them. but not both Non-Linerar Input need special order EQ - DS8B Ordering Code EQ-DS8B I R R R 4 B Default : Input signals : ma, V, mv, rt and pt for option Auxiliary Power Supply : A : DC +2V / 30mA B : DC + 24V / 30mA Communication : Non : No communication 2 : RS232 4 : RS485 AL3 : R : Relay S : SSR / Logic T : SCR N : No Alarm AL2 : R : Relay S : SSR / Logic T : SCR N : No Alarm AL : R : Relay S : SSR / Logic T : SCR N : No Alarm Analogue : Default : No Analogue I : DC 0 ~0mA or DC 4 ~ 20mA Power Supply : Default : AC 90 ~ 260V 50 / 60Hz E : DC 24V DS8B Series of process Indicator Size : 48H x 96W X80L K Page - 03/

4 Specifications : Power Supply : 90~260V AC or 8-30V AC/DC Consumption : 5VA Accuracy : 0.3% F.S. ± 2 digit Sampling Rate : 8 Times / Second Alarm Relay : NO AC 250V/3A or DC 30V /3A cos = Input : Refer the input signal selection Analogue : 0-0V or 4-20mA, free set for control O/P Range by software Auxiliary Power : DC 2 / 24V / 30mA Communication : RS232 or RS485 (Optional) Dimensions : Analogue Low Value Setting Range : LSP brl USP Analogue High Value Setting Range : LSP brh USP Baud Rate select :9 2K Bit/ s 2/3 (reserve) Factory Setting = 9.6Kbit/s Communication Address Selection Range : 000~ F/C NO= º C Yes = º F Parameter Lock W 48H 84L 4 Page -04/ 9 Page - 09/

5 << Press / V key for more than 3 seconds. can enter / quit from the V second grade parameters setting Input Signal Selection : ma V mv Rt Pt Tc Low Display Setting Range : 999~9999 Input High Display Setting Range : 999~9999 Parameter Setting :. Alarm Setting : In the displaying estate, press and hold key for more than 3 seconds, enter alarm mode parameters setting menu. Press << / RST key. LED flashes. Press / key to modify, and then press key to confirm. Press key to read the following parameters one by one. 2. Rate Setting : In displaying estate, press <</RST key and LED flashes, then you can modify the value by Up and Down key. The factory setting is.00. Once the user want to set it to be other value, then PV=Rate (USP-LSP) + LSP USP means Up limit, LSP means Down limit. << Decimal Point Setting : 0~3 Stands for 0000, 000.0, and AL Hysteresis Range : ± 50.0 AL2 Hysteresis Range : ± 50.0 AL3 Hysteresis Range : ± Zero Point Clear : In the displaying estate, without key operation, when the input zero point, press and hold <</RST key for more than 2 seconds. It is for the sensor zero point clear. 4. The instrument will return to the measuring estate without any operation for 25 seconds. Special Function : The instrument can be input by up to 2 signals, the up and down LED can display the measuring value. The instrument can calculate the two input value, so it also can be used as a watt meter. 8 Page -08/ 5 Page - 05/

6 Operation Process : Power ON Alarm 2 Setting, Range LSP AL2 USP All LED on Alarm 2 Mode Setting H : High L : Low Input Signal Type Alarm 2 Hysteresis Value Setting Range : ±50.0 Up limit Down limit PV display Rate Setting Alarm 3 Setting, Range LSP AL3 USP Alarm 3 Mode Setting H : High L : Low Alarm Parameter Setting Alarm 3 Hysteresis Value Setting Range : ±50.0 >3S Measuring Display Rate Setting Offset Value : Display = PV PVF : ± 50 Alarm Setting Range LSP AL USP Alarm mode Setting H : High L : Low Alarm Hysteresis Value Setting. Range : ±50.0 Offset Value : Display = PV PVF : ± 50 Parameter Lock password LCK=000 means the parameter can be modified LCK=00 is for read only 6 Page -06/ 7 Page - 07/

AI-501 INTELLIGENT INDICATING/ALARMING INSTRUMENT. Operation Instruction

AI-501 INTELLIGENT INDICATING/ALARMING INSTRUMENT Operation Instruction CONTENTS Page MAIN FEATURES... 2 ORDERING CODE.3 TECHNICAL SPECIFICATION.5 FRONT PANEL AND OPERATION..6 PARAMETER AND SETTING...