CERTIFICATE. Issued Date: Oct. 03, 2006 Report No.: 069L003-IT-CE-P11V04

Transcription

1 CERTIFICATE Issued Date: Oct. 03, 2006 Report No.: 069L003-IT-CE-P11V04 This is to certify that the following designated product Product : Barebone Trade name : MSI Model Number : MS-6429, Saturn 865, MS-6434, Saturn 800, MS-6437, Saturn 890 Company Name : MICRO-STAR INTL Co., LTD. This product, which has been issued the test report listed as above in QuieTek Laboratory, is based on a single evaluation of one sample and confirmed to comply with the requirements of the following EMC standard. EN 55022: 1998+A1: 2000+A2: 2003 EN 55024: 1998+A1: 2001+A2: 2003 EN : 2000 IEC Edition 1.2: EN : A1: 2001 IEC : 2002+A1: 2002 IEC : 2004 IEC Edition 1.1: IEC Edition 2.1: IEC Edition 1.1: IEC Second Edition: TEST LABORATORY George Chen / President No.5-22, Ruei-Shu Valley, Ruei-Ping Tsuen Lin Kou Shiang, Taipei 244 Taiwan, R.O.C. TEL: FAX: service@quietek.com

2 Test Report Product Name : Barebone Model No. : MS-6429, Saturn 865, MS-6434, Saturn 800, MS-6437, Saturn 890 Applicant : MICRO-STAR INT L Co., LTD. Address : No. 69, Li-De St., Jung-He City, Taipei Hsien, Taiwan, R.O.C. Date of Receipt : 2006/08/28 Issued Date : 2006/10/02 Report No. : 069L003-IT-CE-P11V04 The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standard through the calibration of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by CNLA, NVLAP or any agency of the Government. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation.

3 Declaration of Conformity The following product is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility Directive (89/336/EEC). The listed standards as below were applied: The following Equipment: Product : Barebone Model Number : MS-6429, Saturn 865, MS-6434, Saturn 800, MS-6437, Saturn 890 Trade Name : MSI This product is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility Directive (89/336/EEC). For the evaluation regarding EMC, the following standards were applied: RFI Emission: EN 55022:1998+A1:2000+A2:2003 Class B : Product family standard EN :2000 Class D : Limits for harmonic current emission EN :1995+A1:2001 : Limitation of voltage fluctuation and flicker in low-voltage supply system Immunity: EN 55024:1998+A1:2001+A2:2003 : Product family standard The following importer/manufacturer is responsible for this declaration: Company Name : Company Address : Telephone : Facsimile : Person is responsible for marking this declaration: Name (Full Name) Position/ Title Date Legal Signature

4 QTK No.: 069L003-IT-CE-P11V04 Statement of Conformity This certifies that the following designated product: Product : Barebone Model Number : MS-6429, Saturn 865, MS-6434, Saturn 800, MS-6437, Saturn 890 Trade Name : MSI Company Name : MICRO-STAR INTL Co., LTD. This product is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility Directive (89/336/EEC). For the evaluation regarding EMC, the following standards were applied: RFI Emission: EN 55022:1998+A1:2000+A2:2003 Class B : Product family standard EN :2000 Class D : Limits for harmonic current emission EN :1995+A1:2001 : Limitation of voltage fluctuation and flicker in low-voltage supply system Immunity: EN 55024:1998+A1:2001+A2:2003 : Product family standard TEST LABORATORY 0914 George Chen / President The verification is based on a single evaluation of one sample of above-mentioned products. It does not imply an assessment of the whole production and does not permit the use of the test lab. Logo. QuieTek Corporation / No.5-22, Ruei-Shu Valley, Ruei-Ping Tsuen Lin Kou Shiang, Taipei 244 Taiwan, R.O.C. Tel: , Fax: , service@quietek.com

5 Test Report Certification Issued Date : 2006/10/03 Report No. : 069L003-IT-CE-P11V04 Product Name : Barebone Applicant : MICRO-STAR INT L Co., LTD. Address : No. 69, Li-De St., Jung-He City, Taipei Hsien, Taiwan, R.O.C. Manufacturer : MICRO-STAR INT L Co., LTD. Model No. : MS-6429, Saturn 865, MS-6434, Saturn 800, MS-6437, Saturn 890 Rated Voltage : AC 230 V / 50 Hz EUT Voltage : AC V, 50-60Hz Trade Name : MSI Applicable Standard : EN 55022: 1998+A1: 2000+A2: 2003 Class B EN 55024: 1998+A1: 2001+A2: 2003 EN :2000EN :1995+A1:2001 AS/NZS CISPR 22: 2006 Test Result : Complied Performed Location : Linkou EMC laboratory No.5-22,Ruei-Shu Valley, Ruei-Ping Tsuen Lin Kuo Shiang, Taipei, 244 Taiwan, R.O.C. TEL: / FAX: Documented By : ( Rita Huang ) Reviewed By : ( Kent Yao ) Approved By : ( George Chen ) Page: 2 of 176

6 Laboratory Information We, QuieTek Corporation, are an independent EMC and safety consultancy that was established the whole facility in our laboratories. The test facility has been accredited by the following accreditation Bodies in compliance with ISO 17025, EN and Guide 25: Taiwan R.O.C. : BSMI, DGT, CNLA Germany : TUV Rheinland Norway : Nemko, DNV USA : FCC, NVLAP Japan : VCCI The related certificate for our laboratories about the test site and management system can be downloaded from QuieTek Corporation s Web Site : The address and introduction of QuieTek Corporation s laboratories can be founded in our Web site : If you have any comments, Please don t hesitate to contact us. Our contact information is as below: HsinChu Testing Laboratory : No.75-2, 3rd Lin, Wangye Keng, Yonghxing Tsuen, Qionglin Shiang, Hsinchu County 307, Taiwan, R.O.C. TEL: / FAX: service@quietek.com 1313 LinKou Testing Laboratory : No. 5-22, Ruei-Shu Valley, Ruei-Ping Tsuen, Lin-Kou Shiang, Taipei, Taiwan, R.O.C. TEL : / FAX : service@quietek.com 0914 Page: 3 of 176

7 TABLE OF CONTENTS Description Page 1. General Information EUT Description Mode of Operation Tested System Details Configuration of Tested System EUT Exercise Software Technical Test Summary of Test Result List of Test Equipment Measurement Uncertainty Test Environment Conducted Emission (Main Terminals) Test Specification Test Setup Limit Test Procedure Deviation from Test Standard Test Result Test Photograph Conducted Emissions (Telecommunication Ports) Test Specification Test Setup Limit Test Procedure Deviation from Test Standard Test Result Test Photograph Radiated Emission Test Specification Test Setup Limit Test Procedure Deviation from Test Standard Test Result Test Photograph Harmonic Current Emission Page: 4 of 176

8 6.1. Test Specification Test Setup Limit Test Procedure Deviation from Test Standard Test Result Test Photograph Voltage Fluctuation and Flicker Test Specification Test Setup Limit Test Procedure Deviation from Test Standard Test Result Test Photograph Electrostatic Discharge Test Specification Test Setup Limit Test Procedure Deviation from Test Standard Test Result Test Photograph Radiated Susceptibility Test Specification Test Setup Limit Test Procedure Deviation from Test Standard Test Result Test Photograph Electrical Fast Transient/Burst Test Specification Test Setup Limit Test Procedure Deviation from Test Standard Test Result Page: 5 of 176

9 10.7. Test Photograph Surge Test Specification Test Setup Limit Test Procedure Deviation from Test Standard Test Result Test Photograph Conducted Susceptibility Test Specification Test Setup Limit Test Procedure Deviation from Test Standard Test Result Test Photograph Power Frequency Magnetic Field Test Specification Test Setup Limit Test Procedure Deviation from Test Standard Test Result Test Photograph Voltage Dips and Interruption Test Specification Test Setup Limit Test Procedure Deviation from Test Standard Test Result Test Photograph Attachment EUT Photograph Page: 6 of 176

10 1. General Information 1.1. EUT Description Product Name Barebone Trade Name MSI Model No. MS-6429, Saturn 865, MS-6434, Saturn 800, MS-6437, Saturn 890 Mode 1 Component CPU Mother Board HDD VGA Card LAN Card Sound Card Power Supply DDR-RAM AMD AM2 Sempran(tm), 1.8GHz ADM Processor MSI, MS-7253 Seagate, ST320014A On Board On Board On Board FSP, ATX350F-C Micron, PC2-4200U C0 Mode 2 & Mode 3 Component CPU Intel, Pentium IV (LGA775), 3.4GHz/200MHz, FSB: 800MHz Intel, Pentium IV (LGA775), 3.3GHz/133MHz, FSB: 533MHz Mother Board MSI, MS-7222 HDD Seagate, ST380021A VGA Card On Board LAN Card On Board Sound Card On Board Power Supply FSP, ATX350F-C DDR-RAM Transcend, Page: 7 of 176

11 Mode 4 & Mode 5 Component CPU Mother Board HDD VGA Card LAN Card Sound Card Power Supply DDR-RAM Intel, Pentium IV (LGA775), 3.4GHz/200MHz, FSB: 800MHz Intel, Pentium IV (LGA775), 3.3GHz/133MHz, FSB: 533MHz MSI, MS-7101 Maxtor, 6H500FO On Board On Board On Board FSP, ATX350F-C SAMSUNG, PC3200U EO Note: 1. The different of the each model is shown as below: Model Number MS-6429, Saturn 865 MS-6434, Saturn 800 MS Saturn 890 Description Marketing requirement Marketing requirement Marketing requirement Page: 8 of 176

12 1.2. Mode of Operation QuieTek has verified the construction and function in typical operation. All the test modes were carried out with the EUT in normal operation, which was shown in this test report and defined as: Pre-Test Mode Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Mode 3:MS-6434,Intel Pentium IV(LGA 775)3.3GHz/133MHz,D-Sub(1280*1024/85Hz) Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Mode 5:MS-6429,Intel Pentium IV(LGA 775)3.3GHz/133MHz,D-Sub(1280*1024/85Hz) Mode 6:MS-6437,AMD AM2 Sempron 3400+,D-Sub(1280*1024/85Hz) Mode 7:MS-6437,AMD AM2 Sempron 3400+,D-Sub(800*600/60Hz) Mode 8:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(800*600/60Hz) Mode 9:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(800*600/60Hz) Final Test Mode Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Emission Mode 3:MS-6434,Intel Pentium IV(LGA 775)3.3GHz/133MHz,D-Sub(1280*1024/85Hz) Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Mode 5:MS-6429,Intel Pentium IV(LGA 775)3.3GHz/133MHz,D-Sub(1280*1024/85Hz) Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Immunity Mode 3:MS-6434,Intel Pentium IV(LGA 775)3.3GHz/133MHz,D-Sub(1280*1024/85Hz) Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Mode 5:MS-6429,Intel Pentium IV(LGA 775)3.3GHz/133MHz,D-Sub(1280*1024/85Hz) Page: 9 of 176

13 1.3. Tested System Details The types for all equipments, plus descriptions of all cables used in the tested system (including inserted cards) are: Mode 1 Product Manufacturer Model No. Serial No. Power Cord 1 Modem ACEEX DM Non-Shielded, 1.8m 2 Monitor SONY CPD-G Non-Shielded, 1.8m 3 Walkman AIWA HS-TA164 N/A N/A 4 Microphone & Earphone 5 Microphone & Earphone N/A MIC-06 N/A N/A ROSA RSM-900 N/A Non-Shielded, 1.5m 6 Keyboard COMPAQ KB-0133 B55940MGAPK00W N/A 7 Mouse COMPAQ M-S69 44H0 N/A 8 Printer EPSON StyLus C63 FAPY Non-Shielded, 1.9m 9 Speaker IBM IBM FRU PN 09N Speaker IBM IBM FRU PN 09N Speaker IBM IBM FRU PN 09N COMBO HDD TeraSys F12-UF A b0013 Non-Shielded, 1.8m 13 COMBO HDD TeraSys F12-UF A b0011 Non-Shielded, 1.8m 14 COMBO HDD TeraSys F12-UF A b0002 Non-Shielded, 1.8m 15 COMBO HDD TeraSys F12-UF A b0019 Non-Shielded 1.8m 16 COMBO HDD TeraSys F12-UF A m0031 Non-Shielded 1.8m 17 COMBO HDD TeraSys F12-UF A b0013 Non-Shielded, 1.8m 18 Notebook PC DELL PPT N/A Non-Shielded, 0.8m N/A N/A N/A N/A N/A N/A Page: 10 of 176

14 Mode 2 & Mode 3 & Mode 4 & Mode 5 Product Manufacturer Model No. Serial No. Power Cord 1 Modem ACEEX DM Non-Shielded, 1.8m 2 Monitor SONY CPD-G Non-Shielded, 1.8m 3 Walkman AIWA HS-TA164 N/A N/A 4 Microphone & PCHOME N/A N/A N/A Earphone 5 Microphone & PCHOME N/A N/A N/A Earphone 6 Keyboard COMPAQ KB-0133 B55940MGAPK00W N/A 7 Mouse COMPAQ M-S69 44H0 N/A 8 Printer EPSON StyLus C63 FAPY Non-Shielded, 1.9m 9 COMBO HDD TeraSys F12-UF A m0031 Non-Shielded 1.8m 10 COMBO HDD TeraSys F12-UF A b0013 Non-Shielded, 1.8m 11 COMBO HDD TeraSys F12-UF A m0031 Non-Shielded 1.8m 12 COMBO HDD TeraSys F12-UF A b0019 Non-Shielded 1.8m 13 COMBO HDD TeraSys F12-UF A b0013 Non-Shielded, 1.8m 14 COMBO HDD TeraSys F12-UF A m0031 Non-Shielded 1.8m 15 Notebook PC DELL PPT N/A Non-Shielded, 0.8m Page: 11 of 176

15 1.4. Configuration of Tested System Mode 1 Connection Diagram Signal Cable Type Signal cable Description A RS232 Cable Shielded, 1.5m B D-SUB Cable Shielded, 1.8m, with two ferrite cores bonded C Audio Cable Non-Shielded, 1.6m D Earphone & Microphone Cable Non-Shielded, 1.6m E Earphone & Microphone Cable Non-Shielded, 1.6m F Keyboard Cable Shielded, 1.8m G Mouse Cable Shielded, 1.8m H Printer Cable Shielded, 1.2m I Audio Cable Non-Shielded, 1.6m J Audio Cable Non-Shielded, 1.6m K Audio Cable Non-Shielded, 1.6m L USB Cable Shielded, 1.5m M USB Cable Shielded, 1.5m N USB Cable Shielded, 1.5m O USB Cable Shielded, 1.5m P USB Cable Shielded, 1.5m Q USB Cable Shielded, 1.5m R LAN Cable Non-Shielded, 3.0m Page: 12 of 176

16 Mode 2 & Mode 3 & Mode 4 & Mode 5 Connection Diagram Signal Cable Type Signal cable Description A RS232 Cable Shielded, 1.5m B D-SUB Cable Shielded, 1.8m, with two ferrite cores bonded C Audio Cable Non-Shielded, 1.6m D Earphone & Microphone Cable Non-Shielded, 1.6m E Earphone & Microphone Cable Non-Shielded, 1.6m F Keyboard Cable Shielded, 1.8m G Mouse Cable Shielded, 1.8m H Printer Cable Shielded, 1.2m I USB Cable Shielded, 1.5m J USB Cable Shielded, 1.5m K USB Cable Shielded, 1.5m L USB Cable Shielded, 1.5m M USB Cable Shielded, 1.5m N USB Cable Shielded, 1.5m O LAN Cable Shielded, 3.0m Page: 13 of 176

17 1.5. EUT Exercise Software 1 Setup the EUT and simulators as shown on Turn on the power of all equipment and EUT. 3 EUT reads data from disk. 4 EUT Computer sends H pattern to monitor and printer, the printer will print H pattern on paper. 5 EUT reads and writes data into and from modem. 6 EUT will read data from floppy disk and then writes the data into floppy disk, same operation for hard disk. 7 Repeat the above procedure 3 to 6 8 EUT Connect another simulation PC through LAN port and carry out Read/Write work each other. Page: 14 of 176

18 2. Technical Test 2.1. Summary of Test Result No deviations from the test standards Deviations from the test standards as below description: Emission Performed Item Normative References Test Performed Deviation Conducted Emission EN 55022:1998+A1:2000+A2:2003 Class B Yes No AS/NZS CISPR 22: 2006 Impedance Stabilization EN 55022:1998+A1:2000+A2:2003 Class B Yes No Network AS/NZS CISPR 22: 2006 Radiated Emission EN 55022:1998+A1:2000+A2:2003 Class B Yes No AS/NZS CISPR 22: 2006 Power Harmonics EN :2000 Yes No Voltage Fluctuation and Flicker EN :1995+A1:2001 Yes No Immunity Performed Item Normative References Test Performed Deviation Electrostatic Discharge IEC Edition 1.2: Yes No Radiated susceptibility IEC :2002+A1:2002 Yes No Electrical fast transient/burst IEC :2004 Yes No Surge IEC Edition 1.1: Yes No Conducted susceptibility IEC Edition 2.1: Yes No Power frequency magnetic field IEC Edition 1.1: Yes No Voltage dips and interruption IEC nd Edition: Yes No Page: 15 of 176

19 2.2. List of Test Equipment Conducted Emission / SR1 Instrument Manufacturer Type No. Serial No Cal. Date EMI Test Receiver R&S ESCS / /02/18 LISN R&S ESH3-Z / /02/14 LISN R&S ENV / /07/13 Pulse Limiter R&S ESH3-Z /09/04 Impedance Stabilization Network / SR1 Instrument Manufacturer Type No. Serial No Cal. Date Capacitive Voltage Probe Schaffner CVP2200A /11/11 EMI Test Receiver R&S ESCS / /02/18 LISN R&S ENV / /07/13 LISN R&S ESH3-Z / /02/14 lmpedance Stabilization Network Schaffner ISN T /07/15 Pulse Limiter R&S ESH3-Z /09/04 RF Current Probe FCC F-65 10KHz~1GHz /11/11 Radiated Emission / Site3 Instrument Manufacturer Type No. Serial No Cal. Date Bilog Antenna Schaffner Chase CBL6112B /08/09 Broadband Horn Antenna Schwarzbeck BBHA /07/25 EMI Test Receiver R&S ESI / /06/19 EMI Test Receiver R&S ESCS / /05/11 Horn Antenna Schwarzbeck BBHA9120D /08/10 Pre-Amplifier MITEQ AMF-4D P /01/03 Pre-Amplifier QTK N/A N/A 2006/01/03 Spectrum Analyzer Advantest R /10/24 Power Harmonics / SR3 Instrument Manufacturer Type No. Serial No Cal. Date AC Power Source(Harmonic) Schaffner NSG 1007 HK /6/29 IEC X Analyzer(Flicker) Schaffner CCN X /06/29 Voltage Fluctuation and Flicker / SR3 Instrument Manufacturer Type No. Serial No Cal. Date AC Power Source(Harmonic) Schaffner NSG 1007 HK /6/29 IEC X Analyzer(Flicker) Schaffner CCN X /06/29 Electrostatic Discharge / SR6 Instrument Manufacturer Type No. Serial No Cal. Date ESD Simulator System KeyTek MZ-15/EC /08/02 Horizontal Coupling Plane(HCP) QuieTek HCP AL50 N/A N/A Vertical Coupling Plane(VCP) QuieTek VCP AL50 N/A N/A Page: 16 of 176

20 Radiated susceptibility / CB5 Instrument Manufacturer Type No. Serial No Cal. Date AF-BOX R&S AF-BOX ACCUST N/A Audio Analyzer R&S UPL /03/16 Bilog Antenna Schaffner Chase CBL6112B /01/03 Broad-Band Antenna Schwarzbeck VULB /08/02 CMU200 UNIV.RADIOCOMM R&S CMU /03/16 Directional Coupler A&R DC /08/03 Dual Microphone Supply B&K /08/04 Mouth Simulator B&K /08/04 Power Amplifier A&R 100W10000M7 A N/A Power Amplifier A&R 30S1G N/A Power Meter R&S NRVD(P.M) /04/21 Pre-Amplifier A&R 150A N/A Probe Microphone B&K /08/04 Signal Generator R&S SMY02(9K-208 0) / /10/03 Electrical fast transient/burst / SR2 Instrument Manufacturer Type No. Serial No Cal. Date Schaffner NSG 2050 System Mainframe Surge / SR6 Instrument Manufacturer Type No. Serial No Cal. Date Schaffner NSG 2050 System Mainframe EMC immunity system Thermo EMCPRO PLUS /12/01 Conducted susceptibility / SR6 Instrument Manufacturer Type No. Serial No Cal. Date Schaffner NSG 2070 RF-Generator N/A N/A N/A N/A N/A Power frequency magnetic field / SR3 Instrument Manufacturer Type No. Serial No Cal. Date Induction Coil Interface Schaffner INA N/A Magnetic Loop Coil Schaffner INA IN N/A Magnetic/Electric field measuring system Lackmann Phymetric MV3 N/A N/A Triaxial ELF Magnetic Field Meter F.B.BELL /05/30 Voltage dips and interruption / SR6 Instrument Manufacturer Type No. Serial No Cal. Date Schaffner NSG 2050 System Mainframe EMC immunity system Thermo EMCPRO PLUS /12/01 Page: 17 of 176

21 Schaffner NSG 2050 System Mainframe Instrument Manufacturer Type No. Serial No Cal. Date Burst 4.8KV/16A Generator with CDN Schaffner PNW SC 2005/12/28 Damped osc. Wave 100kHz and 1MHz Schaffner PNW SC 2005/12/28 Double AC Source Variator Schaffner NSG 642A /12/28 Hybrid surge pulse 1.2/50uS Schaffner PNW LU 2006/01/03 PQT Generator Schaffner PNW SC 2006/01/02 Pulse COUPLING NETWORK Schaffner CDN SC 2005/12/28 Schaffner NSG 2070 RF-Generator Instrument Manufacturer Type No. Serial No Cal. Date CDN Schaffner CAL U100A /03/27 CDN Schaffner TRA U /03/27 CDN M016S Schaffner CAL U100A /03/27 CDN M016S Schaffner TRA U /03/27 CDN T002 Schaffner CAL U /03/27 CDN T002 Schaffner TRA U /03/27 CDN T400 Schaffner CAL U /03/27 CDN T400 Schaffner TRA U /03/27 Coupling Decoupling Network Schaffner CDN M016S /03/27 Coupling Decoupling Network Schaffner CDN M016S /03/27 Coupling Decoupling Network Schaffner CDN T /03/27 Coupling Decoupling Network Schaffner CDN T /03/27 EM-CLAMP Schaffner KEMZ /04/21 Page: 18 of 176

22 2.3. Measurement Uncertainty Conducted Emission The measurement uncertainty is evaluated as ± 2.26 db. Impedance Stabilization Network The measurement uncertainty is evaluated as ± 2.26 db. Radiated Emission The measurement uncertainty is evaluated as ± 3.19 db. Electrostatic Discharge As what is concluded in the document from Note2 of clause of ISO/IEC 17025: 1999[2], the requirements for measurement uncertainty in ESD testing are deemed to have been satisfied, and the testing is reported in accordance with the relevant ESD standards. The immunity test signal from the ESD system meet the required specifications in IEC through the calibration report with the calibrated uncertainty for the waveform of voltage and timing as being 1.63 % and 2.76%. Radiated susceptibility As what is concluded in the document from Note2 of clause of ISO/IEC 17025: 1999[2], the requirements for measurement uncertainty in RS testing are deemed to have been satisfied, and the testing is reported in accordance with the relevant RS standards. The immunity test signal from the RS system meet the required specifications in IEC through the calibration for the uniform field strength and monitoring for the test level with the uncertainty evaluation report for the electrical filed strength as being 2.72 db. Electrical fast transient/burst As what is concluded in the document from Note2 of clause of ISO/IEC 17025: 1999[2], the requirements for measurement uncertainty in EFT/Burst testing are deemed to have been satisfied, and the testing is reported in accordance with the relevant EFT/Burst standards. The immunity test signal from the EFT/Burst system meet the required specifications in IEC through the calibration report with the calibrated uncertainty for the waveform of voltage, frequency and timing as being 1.63 %, and 2.76%. Surge As what is concluded in the document from Note2 of clause of ISO/IEC 17025: 1999[2], the requirements for measurement uncertainty in Surge testing are deemed to have been satisfied, and the testing is reported in accordance with the relevant Surge standards. The immunity test signal from the Surge system meet the required specifications in IEC through the calibration report with the calibrated uncertainty for the waveform of voltage and timing as being 1.63 % and 2.76%. Conducted susceptibility Page: 19 of 176

23 As what is concluded in the document from Note2 of clause of ISO/IEC 17025: 1999[2], the requirements for measurement uncertainty in CS testing are deemed to have been satisfied, and the testing is reported in accordance with the relevant CS standards. The immunity test signal from the CS system meet the required specifications in IEC through the calibration for unmodulated signal and monitoring for the test level with the uncertainty evaluation report for the injected modulated signal level through CDN and EM Clamp/Direct Injection as being 3.72 db and 2.78 db. Power frequency magnetic field As what is concluded in the document from Note2 of clause of ISO/IEC 17025: 1999[2], the requirements for measurement uncertainty in PFM testing are deemed to have been satisfied, and the testing is reported in accordance with the relevant PFM standards. The immunity test signal from the PFM system meet the required specifications in IEC through the calibration report with the calibrated uncertainty for the Gauss Meter to verify the output level of magnetic field strength as being 2 %. Voltage dips and interruption As what is concluded in the document from Note2 of clause of ISO/IEC 17025: 1999[2], the requirements for measurement uncertainty in DIP testing are deemed to have been satisfied, and the testing is reported in accordance with the relevant DIP standards. The immunity test signal from the DIP system meet the required specifications in IEC through the calibration report with the calibrated uncertainty for the waveform of voltage and timing as being 1.63 % and 2.76%. Page: 20 of 176

24 2.4. Test Environment Performed Item Items Required Actual Temperature ( C) Conducted Emission Humidity (%RH) Barometric pressure (mbar) Temperature ( C) Impedance Stabilization Humidity (%RH) Network Barometric pressure (mbar) Temperature ( C) Radiated Emission Humidity (%RH) Barometric pressure (mbar) Temperature ( C) Electrostatic Discharge Humidity (%RH) Barometric pressure (mbar) Temperature ( C) Radiated susceptibility Humidity (%RH) Barometric pressure (mbar) Temperature ( C) Electrical fast transient/burst Humidity (%RH) Barometric pressure (mbar) Temperature ( C) Surge Humidity (%RH) Barometric pressure (mbar) Temperature ( C) Conducted susceptibility Humidity (%RH) Barometric pressure (mbar) Temperature ( C) Power frequency Humidity (%RH) Page: 21 of 176

25 magnetic field Voltage dips and interruption Barometric pressure (mbar) Temperature ( C) Humidity (%RH) Barometric pressure (mbar) Page: 22 of 176

26 3. Conducted Emission (Main Terminals) 3.1. Test Specification According to EMC Standard : EN and AS/NZS CISPR 22: Test Setup 3.3. Limit Limits Frequency (MHz) QP AV Remarks: In the above table, the tighter limit applies at the band edges. Page: 23 of 176

27 3.4. Test Procedure The EUT and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.). This provides a 50 ohm /50uH coupling impedance for the measuring equipment. The peripheral devices are also connected to the main power through a LISN that provides a 50ohm/50uH coupling impedance with 50ohm termination. (Please refers to the block diagram of the test setup and photographs.) Both sides of A.C. line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed on conducted measurement. Conducted emissions were invested over the frequency range from 0.15MHz to 30MHz using a receiver bandwidth of 9kHz Deviation from Test Standard No deviation. Page: 24 of 176

28 3.6. Test Result Site : SR-1 Time : 2006/09/26-01:10 Limit : CISPR_B_00M_QP Margin : 10 EUT : BAREBONE Probe : LISN-020(L) - Line1 Power : AC 230V/50Hz Note : Mode 1 Page: 25 of 176

29 Site : SR-1 Time : 2006/09/26-01:12 Limit : CISPR_B_00M_QP Margin : 0 EUT : BAREBONE Probe : LISN-020(L) - Line1 Power : AC 230V/50Hz Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) QUASIPEAK QUASIPEAK 3 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 26 of 176

30 Site : SR-1 Time : 2006/09/26-01:12 Limit : CISPR_B_00M_AV Margin : 0 EUT : BAREBONE Probe : LISN-020(L) - Line1 Power : AC 230V/50Hz Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) AVERAGE AVERAGE 3 * AVERAGE AVERAGE AVERAGE AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 27 of 176

31 Site : SR-1 Time : 2006/09/26-01:13 Limit : CISPR_B_00M_QP Margin : 10 EUT : BAREBONE Probe : LISN-020(N) - Line2 Power : AC 230V/50Hz Note : Mode 1 Page: 28 of 176

32 Site : SR-1 Time : 2006/09/26-01:15 Limit : CISPR_B_00M_QP Margin : 0 EUT : BAREBONE Probe : LISN-020(N) - Line2 Power : AC 230V/50Hz Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) QUASIPEAK QUASIPEAK 3 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 29 of 176

33 Site : SR-1 Time : 2006/09/26-01:15 Limit : CISPR_B_00M_AV Margin : 0 EUT : BAREBONE Probe : LISN-020(N) - Line2 Power : AC 230V/50Hz Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) AVERAGE AVERAGE 3 * AVERAGE AVERAGE AVERAGE AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 30 of 176

34 Site : SR-1 Time : 2006/09/26-02:23 Limit : CISPR_B_00M_QP Margin : 10 EUT : BAREBONE Probe : LISN-020(L) - Line1 Power : AC 230V/50Hz Note : Mode 2 Page: 31 of 176

35 Site : SR-1 Time : 2006/09/26-02:25 Limit : CISPR_B_00M_QP Margin : 0 EUT : BAREBONE Probe : LISN-020(L) - Line1 Power : AC 230V/50Hz Note : Mode 2 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) QUASIPEAK QUASIPEAK 3 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 32 of 176

36 Site : SR-1 Time : 2006/09/26-02:25 Limit : CISPR_B_00M_AV Margin : 0 EUT : BAREBONE Probe : LISN-020(L) - Line1 Power : AC 230V/50Hz Note : Mode 2 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) AVERAGE AVERAGE 3 * AVERAGE AVERAGE AVERAGE AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 33 of 176

37 Site : SR-1 Time : 2006/09/26-02:26 Limit : CISPR_B_00M_QP Margin : 10 EUT : BAREBONE Probe : LISN-020(N) - Line2 Power : AC 230V/50Hz Note : Mode 2 Page: 34 of 176

38 Site : SR-1 Time : 2006/09/26-02:28 Limit : CISPR_B_00M_QP Margin : 0 EUT : BAREBONE Probe : LISN-020(N) - Line2 Power : AC 230V/50Hz Note : Mode 2 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) QUASIPEAK QUASIPEAK 3 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 35 of 176

39 Site : SR-1 Time : 2006/09/26-02:28 Limit : CISPR_B_00M_AV Margin : 0 EUT : BAREBONE Probe : LISN-020(N) - Line2 Power : AC 230V/50Hz Note : Mode 2 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) AVERAGE AVERAGE 3 * AVERAGE AVERAGE AVERAGE AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 36 of 176

40 Site : SR-1 Time : 2006/09/26-02:29 Limit : CISPR_B_00M_QP Margin : 10 EUT : BAREBONE Probe : LISN-020(L) - Line1 Power : AC 230V/50Hz Note : Mode 3 Page: 37 of 176

41 Site : SR-1 Time : 2006/09/26-02:31 Limit : CISPR_B_00M_QP Margin : 0 EUT : BAREBONE Probe : LISN-020(L) - Line1 Power : AC 230V/50Hz Note : Mode 3 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) QUASIPEAK QUASIPEAK 3 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 38 of 176

42 Site : SR-1 Time : 2006/09/26-02:31 Limit : CISPR_B_00M_AV Margin : 0 EUT : BAREBONE Probe : LISN-020(L) - Line1 Power : AC 230V/50Hz Note : Mode 3 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) AVERAGE AVERAGE 3 * AVERAGE AVERAGE AVERAGE AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 39 of 176

43 Site : SR-1 Time : 2006/09/26-02:31 Limit : CISPR_B_00M_QP Margin : 10 EUT : BAREBONE Probe : LISN-020(N) - Line2 Power : AC 230V/50Hz Note : Mode 3 Page: 40 of 176

44 Site : SR-1 Time : 2006/09/26-02:33 Limit : CISPR_B_00M_QP Margin : 0 EUT : BAREBONE Probe : LISN-020(N) - Line2 Power : AC 230V/50Hz Note : Mode 3 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) QUASIPEAK QUASIPEAK 3 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 41 of 176

45 Site : SR-1 Time : 2006/09/26-02:33 Limit : CISPR_B_00M_AV Margin : 0 EUT : BAREBONE Probe : LISN-020(N) - Line2 Power : AC 230V/50Hz Note : Mode 3 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) AVERAGE AVERAGE 3 * AVERAGE AVERAGE AVERAGE AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 42 of 176

46 Site : SR-1 Time : 2006/09/26-03:28 Limit : CISPR_B_00M_QP Margin : 10 EUT : BAREBONE Probe : LISN-020(L) - Line1 Power : AC 230V/50Hz Note : Mode 4 Page: 43 of 176

47 Site : SR-1 Time : 2006/09/26-03:30 Limit : CISPR_B_00M_QP Margin : 0 EUT : BAREBONE Probe : LISN-020(L) - Line1 Power : AC 230V/50Hz Note : Mode 4 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) QUASIPEAK QUASIPEAK 3 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 44 of 176

48 Site : SR-1 Time : 2006/09/26-03:30 Limit : CISPR_B_00M_AV Margin : 0 EUT : BAREBONE Probe : LISN-020(L) - Line1 Power : AC 230V/50Hz Note : Mode 4 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) AVERAGE AVERAGE 3 * AVERAGE AVERAGE AVERAGE AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 45 of 176

49 Site : SR-1 Time : 2006/09/26-03:30 Limit : CISPR_B_00M_QP Margin : 10 EUT : BAREBONE Probe : LISN-020(N) - Line2 Power : AC 230V/50Hz Note : Mode 4 Page: 46 of 176

50 Site : SR-1 Time : 2006/09/26-03:32 Limit : CISPR_B_00M_QP Margin : 0 EUT : BAREBONE Probe : LISN-020(N) - Line2 Power : AC 230V/50Hz Note : Mode 4 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) QUASIPEAK QUASIPEAK 3 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 47 of 176

51 Site : SR-1 Time : 2006/09/26-03:32 Limit : CISPR_B_00M_AV Margin : 0 EUT : BAREBONE Probe : LISN-020(N) - Line2 Power : AC 230V/50Hz Note : Mode 4 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) AVERAGE AVERAGE 3 * AVERAGE AVERAGE AVERAGE AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 48 of 176

52 Site : SR-1 Time : 2006/09/26-03:34 Limit : CISPR_B_00M_QP Margin : 10 EUT : BAREBONE Probe : LISN-020(L) - Line1 Power : AC 230V/50Hz Note : Mode 5 Page: 49 of 176

53 Site : SR-1 Time : 2006/09/26-03:35 Limit : CISPR_B_00M_QP Margin : 0 EUT : BAREBONE Probe : LISN-020(L) - Line1 Power : AC 230V/50Hz Note : Mode 5 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) QUASIPEAK 2 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 50 of 176

54 Site : SR-1 Time : 2006/09/26-03:35 Limit : CISPR_B_00M_AV Margin : 0 EUT : BAREBONE Probe : LISN-020(L) - Line1 Power : AC 230V/50Hz Note : Mode 5 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) AVERAGE AVERAGE 3 * AVERAGE AVERAGE AVERAGE AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 51 of 176

55 Site : SR-1 Time : 2006/09/26-03:36 Limit : CISPR_B_00M_QP Margin : 10 EUT : BAREBONE Probe : LISN-020(N) - Line2 Power : AC 230V/50Hz Note : Mode 5 Page: 52 of 176

56 Site : SR-1 Time : 2006/09/26-03:38 Limit : CISPR_B_00M_QP Margin : 0 EUT : BAREBONE Probe : LISN-020(N) - Line2 Power : AC 230V/50Hz Note : Mode 5 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) QUASIPEAK 2 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 53 of 176

57 Site : SR-1 Time : 2006/09/26-03:38 Limit : CISPR_B_00M_AV Margin : 0 EUT : BAREBONE Probe : LISN-020(N) - Line2 Power : AC 230V/50Hz Note : Mode 5 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) AVERAGE AVERAGE 3 * AVERAGE AVERAGE AVERAGE AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 54 of 176

58 3.7. Test Photograph Test Mode : Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Description : Front View of Conducted Test Test Mode : Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Description : Back View of Conducted Test Page: 55 of 176

59 Test Mode : Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Description : Front View of Conducted Test Test Mode : Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Description : Back View of Conducted Test Page: 56 of 176

60 Test Mode : Mode 3:MS-6434,Intel Pentium IV(LGA 775)3.3GHz/133MHz,D-Sub(1280*1024/85Hz) Description : Front View of Conducted Test Test Mode : Mode 3:MS-6434,Intel Pentium IV(LGA 775)3.3GHz/133MHz,D-Sub(1280*1024/85Hz) Description : Back View of Conducted Test Page: 57 of 176

61 Test Mode : Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Description : Front View of Conducted Test Test Mode : Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Description : Back View of Conducted Test Page: 58 of 176

62 Test Mode : Mode 5:MS-6429,Intel Pentium IV(LGA 775)3.3GHz/133MHz,D-Sub(1280*1024/85Hz) Description : Front View of Conducted Test Test Mode : Mode 5:MS-6429,Intel Pentium IV(LGA 775)3.3GHz/133MHz,D-Sub(1280*1024/85Hz) Description : Back View of Conducted Test Page: 59 of 176

63 4. Conducted Emissions (Telecommunication Ports) 4.1. Test Specification According to EMC Standard : EN and AS/NZS CISPR 22: Test Setup 4.3. Limit Limits Frequency (MHz) QP AV Remarks: The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz~0.50 MHz. Page: 60 of 176

64 4.4. Test Procedure Telecommunication Port: The mains voltage shall be supplied to the EUT via the LISN when the measurement of telecommunication port is performed. The common mode disturbances at the telecommunication port shall be connected to the ISN, which is 150 ohm impedance. Both alternative cables are tested related to the LCL requested. The measurement range is from 150kHz to 30MHz. The bandwidth of measurement is set to 9kHz. The 60dB LCL ISN is used for cat. 5 cable, 50dB LCL ISN is used for cat. 3 and 80dB LCL is used for alternative one Deviation from Test Standard No deviation. Page: 61 of 176

65 4.6. Test Result Site : SR-1 Time : 2006/09/26-05:00 Limit : ISN_Voltage_B_10db_00M_QP Margin : 10 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 1: ISN 100Mbps Page: 62 of 176

66 Site : SR-1 Time : 2006/09/26-05:02 Limit : ISN_Voltage_B_10db_00M_QP Margin : 0 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 1: ISN 100Mbps Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) QUASIPEAK QUASIPEAK 3 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 63 of 176

67 Site : SR-1 Time : 2006/09/26-05:02 Limit : ISN_Voltage_B_10db_00M_AV Margin : 0 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 1: ISN 100Mbps Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) AVERAGE AVERAGE 3 * AVERAGE AVERAGE AVERAGE AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 64 of 176

68 Site : SR-1 Time : 2006/09/26-05:03 Limit : ISN_Voltage_B_10db_00M_QP Margin : 10 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 1: ISN 10Mbps Page: 65 of 176

69 Site : SR-1 Time : 2006/09/26-05:06 Limit : ISN_Voltage_B_10db_00M_QP Margin : 0 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 1: ISN 10Mbps Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK 5 * QUASIPEAK QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 66 of 176

70 Site : SR-1 Time : 2006/09/26-05:06 Limit : ISN_Voltage_B_10db_00M_AV Margin : 0 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 1: ISN 10Mbps Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) AVERAGE AVERAGE 3 * AVERAGE AVERAGE AVERAGE AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 67 of 176

71 Site : SR-1 Time : 2006/09/26-04:38 Limit : ISN_Voltage_B_10db_00M_QP Margin : 10 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 2: ISN 100Mbps Page: 68 of 176

72 Site : SR-1 Time : 2006/09/26-04:41 Limit : ISN_Voltage_B_10db_00M_QP Margin : 0 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 2: ISN 100Mbps Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK 5 * QUASIPEAK QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 69 of 176

73 Site : SR-1 Time : 2006/09/26-04:41 Limit : ISN_Voltage_B_10db_00M_AV Margin : 0 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 2: ISN 100Mbps Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) AVERAGE AVERAGE AVERAGE AVERAGE 5 * AVERAGE AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 70 of 176

74 Site : SR-1 Time : 2006/09/26-04:31 Limit : ISN_Voltage_B_10db_00M_QP Margin : 10 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 2: ISN 10Mbps Page: 71 of 176

75 Site : SR-1 Time : 2006/09/26-04:35 Limit : ISN_Voltage_B_10db_00M_QP Margin : 0 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 2: ISN 10Mbps Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK 5 * QUASIPEAK QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 72 of 176

76 Site : SR-1 Time : 2006/09/26-04:35 Limit : ISN_Voltage_B_10db_00M_AV Margin : 0 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 2: ISN 10Mbps Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) AVERAGE AVERAGE 3 * AVERAGE AVERAGE AVERAGE AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 73 of 176

77 Site : SR-1 Time : 2006/09/26-04:04 Limit : ISN_Voltage_B_10db_00M_QP Margin : 10 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 4: ISN 100Mbps Page: 74 of 176

78 Site : SR-1 Time : 2006/09/26-04:07 Limit : ISN_Voltage_B_10db_00M_QP Margin : 0 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 4: ISN 100Mbps Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK 6 * QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 75 of 176

79 Site : SR-1 Time : 2006/09/26-04:07 Limit : ISN_Voltage_B_10db_00M_AV Margin : 0 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 4: ISN 100Mbps Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) AVERAGE AVERAGE AVERAGE AVERAGE AVERAGE 6 * AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 76 of 176

80 Site : SR-1 Time : 2006/09/26-04:09 Limit : ISN_Voltage_B_10db_00M_QP Margin : 10 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 4: ISN 10Mbps Page: 77 of 176

81 Site : SR-1 Time : 2006/09/26-04:12 Limit : ISN_Voltage_B_10db_00M_QP Margin : 0 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 4: ISN 10Mbps Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK 6 * QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 78 of 176

82 Site : SR-1 Time : 2006/09/26-04:12 Limit : ISN_Voltage_B_10db_00M_AV Margin : 0 EUT : BAREBONE Power : AC 230V/50Hz Probe : ISN-T400 - Line1 Note : Mode 4: ISN 10Mbps Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (db) 1 * AVERAGE AVERAGE AVERAGE AVERAGE AVERAGE AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 79 of 176

83 4.7. Test Photograph Test Mode : Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Description : Front View of ISN Test Test Mode : Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Description : Back View of ISN Test Page: 80 of 176

84 Test Mode : Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Description : Front View of ISN Test Test Mode : Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Description : Back View of ISN Test Page: 81 of 176

85 Test Mode : Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Description : Front View of ISN Test Test Mode : Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Description : Back View of ISN Test Page: 82 of 176

86 5. Radiated Emission 5.1. Test Specification According to EMC Standard : EN and AS/NZS CISPR 22: Test Setup 5.3. Limit Frequency (MHz) Limits Distance (m) dbuv/m Remark: 1. The tighter limit shall apply at the edge between two frequency bands. 2. Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. Page: 83 of 176

87 5.4. Test Procedure The EUT and its simulators are placed on a turn table which is 0.8 meter above ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 10 meters. The antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. Both horizontal and vertical polarization of the antenna are set on measurement. In order to find the maximum emission, all of the interface cables must be manipulated on radiated measurement. Radiated emissions were invested over the frequency range from 30MHz to1ghz using a receiver bandwidth of 120kHz. Radiated was performed at an antenna to EUT distance of 10 meters Deviation from Test Standard No deviation. Page: 84 of 176

88 5.6. Test Result Site : OATS-3 Time : 2006/09/26-14:13 Limit : CISPR_B_10M_QP Margin : 6 EUT : BAREBONE Probe : CBL6112B-(2704) - HORIZONTAL Power : AC 230V/50Hz Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv/m) (db) (dbuv/m) 1 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 85 of 176

89 Site : OATS-3 Time : 2006/09/26-14:03 Limit : CISPR_B_10M_QP Margin : 6 EUT : BAREBONE Probe : CBL6112B-(2704) - VERTICAL Power : AC 230V/50Hz Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv/m) (db) (dbuv/m) QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK 6 * QUASIPEAK QUASIPEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 86 of 176

90 Site : OATS-3 Time : 2006/09/01-16:33 Limit : CISPR_B_10M_QP Margin : 6 EUT : BAREBONE Probe : CBL6112B-(2704) - HORIZONTAL Power : AC 230V/50Hz Note : Mode 2 Frequency (MHz) Correct Factor Reading Level Measure Level Margin (db) Limit (dbuv/m) Detector Type (db) (dbuv/m) QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK 6 * QUASIPEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 87 of 176

91 Site : OATS-3 Time : 2006/09/01-16:22 Limit : CISPR_B_10M_QP Margin : 6 EUT : BAREBONE Probe : CBL6112B-(2704) - VERTICAL Power : AC 230V/50Hz Note : Mode 2 Frequency (MHz) Correct Factor Reading Level Measure Level Margin (db) Limit (dbuv/m) Detector Type (db) (dbuv/m) QUASIPEAK 2 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 88 of 176

92 Site : OATS-3 Time : 2006/09/25-14:58 Limit : CISPR_B_10M_QP Margin : 6 EUT : BAREBONE Probe : CBL6112B-(2704) - HORIZONTAL Power : AC 230V/50Hz Note : Mode 3 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv/m) (db) (dbuv/m) QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK 7 * QUASIPEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 89 of 176

93 Site : OATS-3 Time : 2006/09/25-14:26 Limit : CISPR_B_10M_QP Margin : 6 EUT : BAREBONE Probe : CBL6112B-(2704) - VERTICAL Power : AC 230V/50Hz Note : Mode 3 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv/m) (db) (dbuv/m) 1 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 90 of 176

94 Site : OATS-3 Time : 2006/09/05-10:04 Limit : CISPR_B_10M_QP Margin : 6 EUT : BAREBONE Probe : CBL6112B-(2704) - HORIZONTAL Power : AC 230V/50Hz Note : Mode 4 Frequency (MHz) Correct Factor Reading Level Measure Level Margin (db) Limit (dbuv/m) Detector Type (db) (dbuv/m) QUASIPEAK QUASIPEAK QUASIPEAK 4 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 91 of 176

95 Site : OATS-3 Time : 2006/09/05-10:03 Limit : CISPR_B_10M_QP Margin : 6 EUT : BAREBONE Probe : CBL6112B-(2704) - VERTICAL Power : AC 230V/50Hz Note : Mode 4 Frequency (MHz) Correct Factor Reading Level Measure Level Margin (db) Limit (dbuv/m) Detector Type (db) (dbuv/m) QUASIPEAK QUASIPEAK 3 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 92 of 176

96 Site : OATS-3 Time : 2006/09/25-17:20 Limit : CISPR_B_10M_QP Margin : 6 EUT : BAREBONE Probe : CBL6112B-(2704) - HORIZONTAL Power : AC 230V/50Hz Note : Mode 5 Frequency (MHz) Correct Factor Reading Level Measure Level Margin (db) Limit (dbuv/m) Detector Type (db) (dbuv/m) QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK 5 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 93 of 176

97 Site : OATS-3 Time : 2006/09/25-16:55 Limit : CISPR_B_10M_QP Margin : 6 EUT : BAREBONE Probe : CBL6112B-(2704) - VERTICAL Power : AC 230V/50Hz Note : Mode 5 Frequency (MHz) Correct Factor Reading Level Measure Level Margin (db) Limit (dbuv/m) Detector Type (db) (dbuv/m) QUASIPEAK 2 * QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK QUASIPEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 94 of 176

98 5.7. Test Photograph Test Mode : Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Description : Front View of Radiated Test Test Mode : Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Description : Back View of Radiated Test Page: 95 of 176

99 Test Mode : Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Description : Front View of Radiated Test Test Mode : Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Description : Back View of Radiated Test Page: 96 of 176

100 Test Mode : Mode 3:MS-6434,Intel Pentium IV(LGA 775)3.3GHz/133MHz,D-Sub(1280*1024/85Hz) Description : Front View of Radiated Test Test Mode : Mode 3:MS-6434,Intel Pentium IV(LGA 775)3.3GHz/133MHz,D-Sub(1280*1024/85Hz) Description : Back View of Radiated Test Page: 97 of 176

101 Test Mode : Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Description : Front View of Radiated Test Test Mode : Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Description : Back View of Radiated Test Page: 98 of 176

102 Test Mode : Mode 5:MS-6429,Intel Pentium IV(LGA 775)3.3GHz/133MHz,D-Sub(1280*1024/85Hz) Description : Front View of Radiated Test Test Mode : Mode 5:MS-6429,Intel Pentium IV(LGA 775)3.3GHz/133MHz,D-Sub(1280*1024/85Hz) Description : Back View of Radiated Test Page: 99 of 176

103 6. Harmonic Current Emission 6.1. Test Specification According to EMC Standard : EN Test Setup 6.3. Limit (a) Limits of Class A Harmonics Currents Harmonics Order n Maximum Permissible harmonic current A Harmonics Order n Maximum Permissible harmonic current A Odd harmonics Even harmonics n * 8/n n * 15/n Page: 100 of 176

104 (b) Limits of Class B Harmonics Currents For Class B equipment, the harmonic of the input current shall not exceed the maximum permissible values given in table that is the limit of Class A multiplied by a factor of 1.5. (c) Limits of Class C Harmonics Currents Harmonics Order Maximum Permissible harmonic current Expressed as a percentage of the input current at the fundamental frequency n % λ * n 39 3 (odd harmonics only) *λ is the circuit power factor (d) Limits of Class D Harmonics Currents Harmonics Order n Maximum Permissible harmonic current per watt ma/w Maximum Permissible harmonic current A n 39 (odd harmonics only) 3.85/n See limit of Class A Page: 101 of 176

105 6.4. Test Procedure The EUT is supplied in series with power analyzer from a power source having the same normal voltage and frequency as the rated supply voltage and the equipment under test. And the rated voltage at the supply voltage of EUT of 0.94 times and 1.06 times shall be performed Deviation from Test Standard No deviation. Page: 102 of 176

106 6.6. Test Result Product Barebone Test Item Test Mode Power Harmonics Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Date of Test 2006/09/23 Test Site No.3 Shielded Room Test Result: Pass Source qualification: Normal Current & voltage waveforms Current (Amps) Voltage (Volts) Harmonics and Class D limit line European Limits Current RMS(Amps) Harmonic # Test result: Pass Worst harmonic was #3 with 60.51% of the limit. Page: 103 of 176

107 Test Result: Pass Source qualification: Normal THC(A): 0.44 I-THD(%): POHC(A): POHC Limit(A): Highest parameter values during test: V_RMS (Volts): Frequency(Hz): I_Peak (Amps): I_RMS (Amps): I_Fund (Amps): Crest Factor: Power (Watts): Power Factor: Harm# Harms(avg) 100%Limit %of Limit Harms(max) 150%Limit %of Limit Status Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Dynamic limits were applied for this test. The highest harmonics values in the above table may not occur at the same window as the maximum harmonics/limit ratio. 2:According to EN paragraph 7 the note 1 and 2 are valid for all applications having an active input power >75W. Others the result should be pass. Page: 104 of 176

108 Product Barebone Test Item Power Harmonics Test Mode Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Date of Test 2006/09/23 Test Site No.3 Shielded Room Test Result: Pass Source qualification: Normal Current & voltage waveforms Current (Amps) Voltage (Volts) Harmonics and Class D limit line European Limits Current RMS(Amps) Harmonic # Test result: Pass Worst harmonic was #3 with 59.83% of the limit. Page: 105 of 176

109 Test Result: Pass Source qualification: Normal THC(A): 0.52 I-THD(%): POHC(A): POHC Limit(A): Highest parameter values during test: V_RMS (Volts): Frequency(Hz): I_Peak (Amps): I_RMS (Amps): I_Fund (Amps): Crest Factor: Power (Watts): Power Factor: Harm# Harms(avg) 100%Limit %of Limit Harms(max) 150%Limit %of Limit Status Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Dynamic limits were applied for this test. The highest harmonics values in the above table may not occur at the same window as the maximum harmonics/limit ratio. 2:According to EN paragraph 7 the note 1 and 2 are valid for all applications having an active input power >75W. Others the result should be pass. Page: 106 of 176

110 Product Barebone Test Item Power Harmonics Test Mode Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Date of Test 2006/09/23 Test Site No.3 Shielded Room Test Result: Pass Source qualification: Normal Current & voltage waveforms Current (Amps) Voltage (Volts) Harmonics and Class D limit line European Limits Current RMS(Amps) Harmonic # Test result: Pass Worst harmonic was #3 with 59.75% of the limit. Page: 107 of 176

111 Test Result: Pass Source qualification: Normal THC(A): 0.49 I-THD(%): POHC(A): POHC Limit(A): Highest parameter values during test: V_RMS (Volts): Frequency(Hz): I_Peak (Amps): I_RMS (Amps): I_Fund (Amps): Crest Factor: Power (Watts): Power Factor: Harm# Harms(avg) 100%Limit %of Limit Harms(max) 150%Limit %of Limit Status Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Dynamic limits were applied for this test. The highest harmonics values in the above table may not occur at the same window as the maximum harmonics/limit ratio. 2:According to EN paragraph 7 the note 1 and 2 are valid for all applications having an active input power >75W. Others the result should be pass. Page: 108 of 176

112 6.7. Test Photograph Test Mode : Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Description : Power Harmonics Test Setup Test Mode : Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Description : Power Harmonics Test Setup Page: 109 of 176

113 Test Mode : Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Description : Power Harmonics Test Setup Page: 110 of 176

114 7. Voltage Fluctuation and Flicker 7.1. Test Specification According to EMC Standard : EN Test Setup 7.3. Limit The following limits apply: - the value of P st shall not be greater than 1.0; - the value of P lt shall not be greater than 0.65; - the value of d(t) during a voltage change shall not exceed 3.3 % for more than 500 ms; - the relative steady-state voltage change, d c, shall not exceed 3.3 %; - the maximum relative voltage change, d max, shall not exceed; a) 4 % without additional conditions; b) 6 % for equipment which is: - switched manually, or - switched automatically more frequently than twice per day, and also has either a delayed restart (the delay being not less than a few tens of seconds), or manual restart, after a power supply interruption. NOTE The cycling frequency will be further limited by the P st and P 1t limit. For example: a d max of 6%producing a rectangular voltage change characteristic twice per hour will give a P 1t of about Page: 111 of 176

115 c) 7 % for equipment which is: - attended whilst in use (for example: hair dryers, vacuum cleaners, kitchen equipment such as mixers, garden equipment such as lawn mowers, portable tools such as electric drills), or - switched on automatically, or is intended to be switched on manually, no more than twice per day, and also has either a delayed restart (the delay being not less than a few tens of seconds) or manual restart, after a power supply interruption. P st and P 1t requirements shall not be applied to voltage changes caused by manual switching Test Procedure The EUT is supplied in series with power analyzer from a power source having the same normal voltage and frequency as the rated supply voltage and the equipment under test. And the rated voltage at the supply voltage of EUT of 0.94 times and 1.06 times shall be performed Deviation from Test Standard No deviation. Page: 112 of 176

116 7.6. Test Result Product Barebone Test Item Test Mode Voltage Fluctuation and Flicker Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Date of Test 2006/09/23 Test Site No.3 Shielded Room Test Result: Pass Status: Test Completed Pst i and limit line European Limits Pst :27:36 Plt and limit line Plt :27:36 Parameter values recorded during the test: Vrms at the end of test (Volt): Highest dt (%): 0.00 Test limit (%): 3.30 Pass Time(mS) > dt: 0.0 Test limit (ms): Pass Highest dc (%): 0.00 Test limit (%): 3.30 Pass Highest dmax (%): 0.00 Test limit (%): 4.00 Pass Highest Pst (10 min. period): Test limit: Pass Highest Plt (2 hr. period): Test limit: Pass Page: 113 of 176

117 Product Barebone Test Item Voltage Fluctuation and Flicker Test Mode Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Date of Test 2006/09/23 Test Site No.3 Shielded Room Test Result: Pass Status: Test Completed Pst i and limit line European Limits Pst :32:00 Plt and limit line Plt :32:00 Parameter values recorded during the test: Vrms at the end of test (Volt): Highest dt (%): 0.00 Test limit (%): 3.30 Pass Time(mS) > dt: 0.0 Test limit (ms): Pass Highest dc (%): 0.00 Test limit (%): 3.30 Pass Highest dmax (%): 0.00 Test limit (%): 4.00 Pass Highest Pst (10 min. period): Test limit: Pass Highest Plt (2 hr. period): Test limit: Pass Page: 114 of 176

118 Product Barebone Test Item Voltage Fluctuation and Flicker Test Mode Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Date of Test 2006/09/23 Test Site No.3 Shielded Room Test Result: Pass Status: Test Completed Pst i and limit line European Limits Pst :58:57 Plt and limit line Plt :58:57 Parameter values recorded during the test: Vrms at the end of test (Volt): Highest dt (%): 0.00 Test limit (%): 3.30 Pass Time(mS) > dt: 0.0 Test limit (ms): Pass Highest dc (%): 0.00 Test limit (%): 3.30 Pass Highest dmax (%): 0.00 Test limit (%): 4.00 Pass Highest Pst (10 min. period): Test limit: Pass Highest Plt (2 hr. period): Test limit: Pass Page: 115 of 176

119 7.7. Test Photograph Test Mode : Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Description : Flicker Test Setup Test Mode : Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Description : Flicker Test Setup Page: 116 of 176

120 Test Mode : Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Description : Flicker Test Setup Page: 117 of 176

121 8. Electrostatic Discharge 8.1. Test Specification According to Standard : IEC Test Setup 8.3. Limit Item Environmental Phenomena Units Test Specification Performance Criteria Enclosure Port Electrostatic Discharge kv(charge Voltage) ±8 Air Discharge ±4 Contact Discharge B Page: 118 of 176

122 8.4. Test Procedure Direct application of discharges to the EUT: Contact discharge was applied only to conductive surfaces of the EUT. Air discharges were applied only to non-conductive surfaces of the EUT. During the test, it was performed with single discharges. For the single discharge time between successive single discharges will be keep longer 1 second. It was at least ten single discharges with positive and negative at the same selected point. The selected point, which was performed with electrostatic discharge, was marked on the red label of the EUT. Indirect application of discharges to the EUT: Vertical Coupling Plane (VCP): The coupling plane, of dimensions 0.5m x 0.5m, is placed parallel to, and positioned at a distance 0.1m from, the EUT, with the Discharge Electrode touching the coupling plane. The four faces of the EUT will be performed with electrostatic discharge. It was at least ten single discharges with positive and negative at the same selected point. Horizontal Coupling Plane (HCP): The coupling plane is placed under to the EUT. The generator shall be positioned vertically at a distance of 0.1m from the EUT, with the Discharge Electrode touching the coupling plane. The four faces of the EUT will be performed with electrostatic discharge. It was at least ten single discharges with positive and negative at the same selected point Deviation from Test Standard No deviation. Page: 119 of 176

123 8.6. Test Result Product Barebone Test Item Test Mode Electrostatic Discharge Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Date of Test 2006/09/27 Test Site No.6 Shielded Room Item Amount of Discharge Voltage Required Criteria Complied To Criteria (A,B,C) Results Air Discharge kV -8kV B B B B Pass Pass Contact Discharge kV -4kV B B A A Pass Pass Indirect Discharge 50 +4kV B A Pass (HCP) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Front) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Left) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Back) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Right) 50-4kV B A Pass Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. NR: No Requirement Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at kv. No false alarms or other malfunctions were observed during or after the test. Remark: The Contact discharges were applied at least total 200 discharges at a minimum of four test points. Page: 120 of 176

124 Product Barebone Test Item Electrostatic Discharge Test Mode Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Date of Test 2006/09/27 Test Site No.6 Shielded Room Item Amount of Discharge Voltage Required Criteria Complied To Criteria (A,B,C) Results Air Discharge kV -8kV B B B B Pass Pass Contact Discharge kV -4kV B B A A Pass Pass Indirect Discharge 50 +4kV B A Pass (HCP) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Front) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Left) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Back) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Right) 50-4kV B A Pass Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. NR: No Requirement Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at kv. No false alarms or other malfunctions were observed during or after the test. Remark: The Contact discharges were applied at least total 200 discharges at a minimum of four test points. Page: 121 of 176

125 Product Barebone Test Item Electrostatic Discharge Test Mode Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Date of Test 2006/09/27 Test Site No.3 Shielded Room Item Amount of Discharge Voltage Required Criteria Complied To Criteria (A,B,C) Results Air Discharge kV -8kV B B B B Pass Pass Contact Discharge kV -4kV B B A A Pass Pass Indirect Discharge 50 +4kV B A Pass (HCP) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Front) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Left) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Back) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Right) 50-4kV B A Pass Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. NR: No Requirement Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at kv. No false alarms or other malfunctions were observed during or after the test. Remark: The Contact discharges were applied at least total 200 discharges at a minimum of four test points. Page: 122 of 176

126 8.7. Test Photograph Test Mode : Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Description : ESD Test Setup Test Mode : Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Description : ESD Test Setup Page: 123 of 176

127 Test Mode : Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Description : ESD Test Setup Page: 124 of 176

128 9. Radiated Susceptibility 9.1. Test Specification According to Standard : IEC Test Setup 9.3. Limit Item Environmental Units Test Performance Phenomena Specification Criteria Enclosure Port Radio-Frequency MHz Electromagnetic Field Amplitude Modulated V/m(Un-modulated, rms) % AM (1kHz) 3 80 A Page: 125 of 176

129 9.4. Test Procedure The EUT and load, which are placed on a table that is 0.8 meter above ground, are placed with one coincident with the calibration plane such that the distance from antenna to the EUT was 3 meters. Both horizontal and vertical polarization of the antenna and four sides of the EUT are set on measurement. In order to judge the EUT performance, a CCD camera is used to monitor EUT screen. All the scanning conditions are as follows: Condition of Test Remarks 1. Field Strength 3 V/m Level 2 2. Radiated Signal AM 80% Modulated with 1kHz 3. Scanning Frequency 80MHz MHz 4 Dwell Time 3 Seconds 5. Frequency step size f : 1% 6. The rate of Swept of Frequency 1.5 x 10-3 decades/s 9.5. Deviation from Test Standard No deviation. Page: 126 of 176

130 9.6. Test Result Product Barebone Test Item Test Mode Radiated susceptibility Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Date of Test 2006/09/26 Test Site Chamber5 Field Complied Frequency Position Polarity Required Strength To Criteria (MHz) (Angle) (H or V) Criteria (V/m) (A,B,C) Results FRONT H 3 A A PASS FRONT V 3 A A PASS BACK H 3 A A PASS BACK V 3 A A PASS RIGHT H 3 A A PASS RIGHT V 3 A A PASS LEFT H 3 A A PASS LEFT V 3 A A PASS UP H 3 A A PASS UP V 3 A A PASS DOWN H 3 A A PASS DOWN V 3 A A PASS Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information There was no observable degradation in performance. EUT stopped operation and could / could not be reset by operator at at frequency MHz. No false alarms or other malfunctions were observed during or after the test. V/m Page: 127 of 176

131 Product Barebone Test Item Radiated susceptibility Test Mode Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Date of Test 2006/09/26 Test Site Chamber5 Field Complied Frequency Position Polarity Required Strength To Criteria (MHz) (Angle) (H or V) Criteria (V/m) (A,B,C) Results FRONT H 3 A A PASS FRONT V 3 A A PASS BACK H 3 A A PASS BACK V 3 A A PASS RIGHT H 3 A A PASS RIGHT V 3 A A PASS LEFT H 3 A A PASS LEFT V 3 A A PASS UP H 3 A A PASS UP V 3 A A PASS DOWN H 3 A A PASS DOWN V 3 A A PASS Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information There was no observable degradation in performance. EUT stopped operation and could / could not be reset by operator at at frequency MHz. No false alarms or other malfunctions were observed during or after the test. V/m Page: 128 of 176

132 Product Barebone Test Item Radiated susceptibility Test Mode Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Date of Test 2006/09/26 Test Site Chamber5 Field Complied Frequency Position Polarity Required Strength To Criteria (MHz) (Angle) (H or V) Criteria (V/m) (A,B,C) Results FRONT H 3 A A PASS FRONT V 3 A A PASS BACK H 3 A A PASS BACK V 3 A A PASS RIGHT H 3 A A PASS RIGHT V 3 A A PASS LEFT H 3 A A PASS LEFT V 3 A A PASS UP H 3 A A PASS UP V 3 A A PASS DOWN H 3 A A PASS DOWN V 3 A A PASS Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information There was no observable degradation in performance. EUT stopped operation and could / could not be reset by operator at at frequency MHz. No false alarms or other malfunctions were observed during or after the test. V/m Page: 129 of 176

133 9.7. Test Photograph Test Mode : Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Description : Radiated Susceptibility Test Setup Test Mode : Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Description : Radiated Susceptibility Test Setup Page: 130 of 176

134 Test Mode : Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Description : Radiated Susceptibility Test Setup Page: 131 of 176

135 10. Electrical Fast Transient/Burst Test Specification According to Standard : IEC Test Setup Limit Item Environmental Phenomena I/O and communication ports Fast Transients Common Mode Input DC Power Ports Fast Transients Common Mode Input AC Power Ports Fast Transients Common Mode Units kv (Peak) Tr/Th ns Rep. Frequency khz kv (Peak) Tr/Th ns Rep. Frequency khz kv (Peak) Tr/Th ns Rep. Frequency khz Test Specification Performance Criteria / / /50 5 B B B Page: 132 of 176

136 10.4. Test Procedure The EUT is placed on a table that is 0.8 meter height. A ground reference plane is placed on the table, and uses a 0.1m insulation between the EUT and ground reference plane. The minimum area of the ground reference plane is 1m*1m, and 0.65mm thick min, and projected beyond the EUT by at least 0.1m on all sides. Test on I/O and communication ports: The EFT interference signal is through a coupling clamp device couples to the signal and control lines of the EUT with burst noise for 1minute. Test on power supply ports: The EUT is connected to the power mains through a coupling device that directly couples the EFT/B interference signal. Each of the Line and Neutral conductors is impressed with burst noise for 1 minute. The length of the signal and power lines between the coupling device and the EUT is 0.5m Deviation from Test Standard No deviation. Page: 133 of 176

137 10.6. Test Result Product Barebone Test Item Test Mode Electrical fast transient/burst Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Date of Test 2006/09/26 Test Site No.2 Shielded Room Inject Line Polarity Voltage kv Inject Time (Second) Inject Method Required Criteria Complied to Criteria Result L+N+PE ± 1kV 60 CDN B B PASS LAN ± 1 kv 90 Clamp B A PASS Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at Line. No false alarms or other malfunctions were observed during or after the test. kv of Page: 134 of 176

138 Product Barebone Test Item Electrical fast transient/burst Test Mode Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Date of Test 2006/09/26 Test Site No.2 Shielded Room Inject Line Polarity Voltage kv Inject Time (Second) Inject Method Required Criteria Complied to Criteria Result L+N+PE ± 1kV 60 CDN B B PASS LAN ± 1 kv 90 Clamp B A PASS Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at Line. No false alarms or other malfunctions were observed during or after the test. kv of Page: 135 of 176

139 Product Barebone Test Item Electrical fast transient/burst Test Mode Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Date of Test 2006/09/26 Test Site No.2 Shielded Room Inject Line Polarity Voltage kv Inject Time (Second) Inject Method Required Criteria Complied to Criteria Result L+N+PE ± 1kV 60 CDN B B PASS LAN ± 1 kv 90 Clamp B A PASS Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at Line. No false alarms or other malfunctions were observed during or after the test. kv of Page: 136 of 176

140 10.7. Test Photograph Test Mode : Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Description : EFT/B Test Setup Test Mode : Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Description : EFT/B Test Setup - Clamp Page: 137 of 176

141 Test Mode : Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Description : EFT/B Test Setup Test Mode : Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Description : EFT/B Test Setup - Clamp Page: 138 of 176

142 Test Mode : Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Description : EFT/B Test Setup Test Mode : Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Description : EFT/B Test Setup - Clamp Page: 139 of 176

143 11. Surge Test Specification According to Standard : IEC Test Setup Limit Item Environmental Phenomena Units Signal Ports and Telecommunication Ports(See 1) and 2) ) Surges Tr/Th us Line to Ground kv Input DC Power Ports Surges Tr/Th us Line to Ground kv AC Input and AC Output Power Ports Surges Tr/Th us Line to Line kv Line to Ground kv Notes: Test Specification Performance Criteria 1.2/50 (8/20) ± 1 1.2/50 (8/20) ± /50 (8/20) ± 1 ± 2 1) Applicable only to ports which according to the manufacturer s may directly to outdoor cables. 2) Where normal functioning cannot be achieved because of the impact of the CDN on the EUT, no immunity test shall be required. B B B Page: 140 of 176

144 11.4. Test Procedure The EUT and its load are placed on a table that is 0.8 meter above a metal ground plane measured 1m*1m min. and 0.65mm thick min. And projected beyond the EUT by at least 0.1m on all sides. The length of power cord between the coupling device and the EUT shall be 2m or less. For Input and Output AC Power or DC Input and DC Output Power Ports: The EUT is connected to the power mains through a coupling device that directly couples the Surge interference signal. The surge noise shall be applied synchronized to the voltage phase at 0 0, 90 0, 180 0, and the peak value of the a.c. voltage wave. (Positive and negative) Each of Line-Earth and Line-Line is impressed with a sequence of five surge voltages with interval of 1 min Deviation from Test Standard No deviation. Page: 141 of 176

145 11.6. Test Result Product Barebone Test Item Test Mode Surge Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Date of Test 2006/09/23 Test Site No.6 Shielded Room Inject Line Polarity Angle Voltage kv Time Interval (Second) Inject Method Required Criteria Complie d to Criteria Result L-N ± 0 1kV 60 Direct B A PASS L-N ± 90 1kV 60 Direct B A PASS L-N ± 180 1kV 60 Direct B A PASS L-N ± 270 1kV 60 Direct B A PASS L-PE ± 0 2kV 60 Direct B A PASS L-PE ± 90 2kV 60 Direct B A PASS L-PE ± 180 2kV 60 Direct B A PASS L-PE ± 270 2kV 60 Direct B A PASS N-PE ± 0 2kV 60 Direct B A PASS N-PE ± 90 2kV 60 Direct B A PASS N-PE ± 180 2kV 60 Direct B A PASS N-PE ± 270 2kV 60 Direct B A PASS Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at kv of Line. No false alarms or other malfunctions were observed during or after the test. Page: 142 of 176

146 Product Barebone Test Item Surge Test Mode Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Date of Test 2006/09/23 Test Site No.6 Shielded Room Voltage Time Complie Inject Inject Required Polarity Angle Interval d to Line Method Criteria kv (Second) Criteria Result L-N ± 0 1kV 60 Direct B A PASS L-N ± 90 1kV 60 Direct B A PASS L-N ± 180 1kV 60 Direct B A PASS L-N ± 270 1kV 60 Direct B A PASS L-PE ± 0 2kV 60 Direct B A PASS L-PE ± 90 2kV 60 Direct B A PASS L-PE ± 180 2kV 60 Direct B A PASS L-PE ± 270 2kV 60 Direct B A PASS N-PE ± 0 2kV 60 Direct B A PASS N-PE ± 90 2kV 60 Direct B A PASS N-PE ± 180 2kV 60 Direct B A PASS N-PE ± 270 2kV 60 Direct B A PASS Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at kv of Line. No false alarms or other malfunctions were observed during or after the test. Page: 143 of 176

147 Product Barebone Test Item Surge Test Mode Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Date of Test 2006/09/23 Test Site No.6 Shielded Room Voltage Time Complie Inject Inject Required Polarity Angle Interval d to Line Method Criteria kv (Second) Criteria Result L-N ± 0 1kV 60 Direct B A PASS L-N ± 90 1kV 60 Direct B A PASS L-N ± 180 1kV 60 Direct B A PASS L-N ± 270 1kV 60 Direct B A PASS L-PE ± 0 2kV 60 Direct B A PASS L-PE ± 90 2kV 60 Direct B A PASS L-PE ± 180 2kV 60 Direct B A PASS L-PE ± 270 2kV 60 Direct B A PASS N-PE ± 0 2kV 60 Direct B A PASS N-PE ± 90 2kV 60 Direct B A PASS N-PE ± 180 2kV 60 Direct B A PASS N-PE ± 270 2kV 60 Direct B A PASS Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at kv of Line. No false alarms or other malfunctions were observed during or after the test. Page: 144 of 176

148 11.7. Test Photograph Test Mode : Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Description : SURGE Test Setup Test Mode : Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Description : SURGE Test Setup Page: 145 of 176

149 Test Mode : Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Description : SURGE Test Setup Page: 146 of 176

150 12. Conducted Susceptibility Test Specification According to Standard : IEC Test Setup CDN Test Mode EM Clamp Test Mode Page: 147 of 176

151 12.3. Limit Item Environmental Phenomena Units Signal Ports and Telecommunication Ports Radio-Frequency Continuous Conducted Input DC Power Ports Radio-Frequency Continuous Conducted Input AC Power Ports Radio-Frequency Continuous Conducted Test Procedure MHz V (rms, Un-modulated) % AM (1kHz) MHz V (rms, Un-modulated) % AM (1kHz) MHz V (rms, Un-modulated) % AM (1kHz) Test Specification Performance Criteria A A A The EUT are placed on a table that is 0.8 meter height, and a Ground reference plane on the table, EUT are placed upon table and use a 10cm insulation between the EUT and Ground reference plane. For Signal Ports and Telecommunication Ports The disturbance signal is through a coupling and decoupling networks (CDN) or EM-clamp device couples to the signal and Telecommunication lines of the EUT. For Input DC and AC Power Ports The EUT is connected to the power mains through a coupling and decoupling networks for power supply lines. And directly couples the disturbances signal into EUT. Used CDN-M2 for two wires or CDN-M3 for three wires. All the scanning conditions are as follows: Condition of Test Remarks 1. Field Strength 130dBuV(3V) Level 2 2. Radiated Signal AM 80% Modulated with 1kHz 3. Scanning Frequency 0.15MHz 80MHz 4 Dwell Time 3 Seconds 5. Frequency step size f : 1% 6. The rate of Swept of Frequency 1.5 x 10-3 decades/s Deviation from Test Standard No deviation. Page: 148 of 176

152 12.6. Test Result Product Barebone Test Item Test Mode Conducted susceptibility Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Date of Test 2006/09/26 Test Site No.6 Shielded Room Frequency Voltage Inject Tested Port Required Performanc Result Range Applied Method of Criteria e Criteria (MHz) dbuv(v) EUT Complied To 0.15~ (3V) CDN AC IN A A PASS 0.15~ (3V) CDN LAN A A PASS Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at dbuv(v) at frequency MHz. No false alarms or other malfunctions were observed during or after the test. The acceptance criteria were met, and the EUT passed the test. Page: 149 of 176

153 Product Barebone Test Item Conducted susceptibility Test Mode Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Date of Test 2006/09/26 Test Site No.6 Shielded Room Frequency Voltage Inject Tested Port Required Performanc Result Range Applied Method of Criteria e Criteria (MHz) dbuv(v) EUT Complied To 0.15~ (3V) CDN AC IN A A PASS 0.15~ (3V) CDN LAN A A PASS Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at dbuv(v) at frequency MHz. No false alarms or other malfunctions were observed during or after the test. The acceptance criteria were met, and the EUT passed the test. Page: 150 of 176

154 Product Barebone Test Item Conducted susceptibility Test Mode Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Date of Test 2006/09/26 Test Site No.6 Shielded Room Frequency Voltage Inject Tested Port Required Performanc Result Range Applied Method of Criteria e Criteria (MHz) dbuv(v) EUT Complied To 0.15~ (3V) CDN AC IN A A PASS 0.15~ (3V) CDN LAN A A PASS Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at dbuv(v) at frequency MHz. No false alarms or other malfunctions were observed during or after the test. The acceptance criteria were met, and the EUT passed the test. Page: 151 of 176

155 12.7. Test Photograph Test Mode : Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Description : Conducted Susceptibility Test Setup Test Mode : Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Description : Conducted Susceptibility Test Setup - CDN Page: 152 of 176

156 Test Mode : Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Description : Conducted Susceptibility Test Setup Test Mode : Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Description : Conducted Susceptibility Test Setup - CDN Page: 153 of 176

157 Test Mode : Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Description : Conducted Susceptibility Test Setup Test Mode : Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Description : Conducted Susceptibility Test Setup - CDN Page: 154 of 176

158 13. Power Frequency Magnetic Field Test Specification According to Standard : IEC Test Setup Limit Item Environmental Phenomena Enclosure Port Power-Frequency Magnetic Field Test Procedure Units Hz A/m (r.m.s.) Test Specification Performance Criteria 50 1 A The EUT and its load are placed on a table which is 0.8 meter above a metal ground plane measured at least 1m*1m min. The test magnetic field shall be placed at central of the induction coil. The test magnetic Field shall be applied 10 minutes by the immersion method to the EUT. And the induction coil shall be rotated by 90 in order to expose the EUT to the test field with different orientation (X, Y, Z Orientations) Deviation from Test Standard No deviation. Page: 155 of 176

159 13.6. Test Result Product Barebone Test Item Test Mode Power frequency magnetic field Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Date of Test 2006/09/27 Test Site No.3 Shielded Room Polarization Frequency Magnetic Required Performance Test Result (Hz) Strength Performance Criteria (A/m) Criteria Complied To X Orientation 50 1 A A PASS Y Orientation 50 1 A A PASS Z Orientation 50 1 A A PASS Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at of Line. No false alarms or other malfunctions were observed during or after the test. The acceptance criteria were met, and the EUT passed the test. kv Page: 156 of 176

160 Product Barebone Test Item Power frequency magnetic field Test Mode Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Date of Test 2006/09/27 Test Site No.3 Shielded Room Polarization Frequency Magnetic Required Performance Test Result (Hz) Strength Performance Criteria (A/m) Criteria Complied To X Orientation 50 1 A A PASS Y Orientation 50 1 A A PASS Z Orientation 50 1 A A PASS Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at of Line. No false alarms or other malfunctions were observed during or after the test. The acceptance criteria were met, and the EUT passed the test. kv Page: 157 of 176

161 Product Barebone Test Item Power frequency magnetic field Test Mode Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Date of Test 2006/09/27 Test Site No.3 Shielded Room Polarization Frequency Magnetic Required Performance Test Result (Hz) Strength Performance Criteria (A/m) Criteria Complied To X Orientation 50 1 A A PASS Y Orientation 50 1 A A PASS Z Orientation 50 1 A A PASS Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at of Line. No false alarms or other malfunctions were observed during or after the test. The acceptance criteria were met, and the EUT passed the test. kv Page: 158 of 176

162 13.7. Test Photograph Test Mode : Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Description : Power Frequency Magnetic Field Test Setup Test Mode : Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Description : Power Frequency Magnetic Field Test Setup Page: 159 of 176

163 Test Mode : Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Description : Power Frequency Magnetic Field Test Setup Page: 160 of 176

164 14. Voltage Dips and Interruption Test Specification According to Standard : IEC Test Setup Limit Item Environmental Phenomena Input AC Power Ports Voltage Dips Voltage Interruptions Units % Reduction Period % Reduction Period % Reduction Period Test Specification Performance Criteria 30 C 25 >95 B 0.5 > 95 C 250 Page: 161 of 176

165 14.4. Test Procedure The EUT and its load are placed on a table which is 0.8 meter above a metal ground plane measured 1m*1m min. And 0.65mm thick min. And projected beyond the EUT by at least 0.1m on all sides. The power cord shall be used the shortest power cord as specified by the manufacturer. For Voltage Dips/ Interruptions test: The selection of test voltage is based on the rated power range. If the operation range is large than 20% of lower power range, both end of specified voltage shall be tested. Otherwise, the typical voltage specification is selected as test voltage. The EUT is connected to the power mains through a coupling device that directly couples to the Voltage Dips and Interruption Generator. The EUT shall be tested for 30% voltage dip of supplied voltage and duration 25 Periods, for 95% voltage dip of supplied voltage and duration 0.5 Periods with a sequence of three voltage dips with intervals of 10 seconds, and for 95% voltage interruption of supplied voltage and duration 250 Periods with a sequence of three voltage interruptions with intervals of 10 seconds. Voltage phase shifting are shall occur at 0 0, 45 0, 90 0,135 0,180 0,225 0, 270 0,315 0 of the voltage Deviation from Test Standard No deviation. Page: 162 of 176

166 14.6. Test Result Product Barebone Test Item Test Mode Voltage dips and interruption Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Date of Test 2006/09/26 Test Site No.6 Shielded Room Voltage Dips and Interruption Reduction(%) Angle Test Duration (Periods) Required Performance Criteria Performance Test Result Criteria Complied To 30(161V) 0 25 C A PASS 30(161V) C A PASS 30(161V) C A PASS 30(161V) C A PASS 30(161V) C A PASS 30(161V) C A PASS 30(161V) C A PASS 30(161V) C A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information The nominal voltage of EUT is 230V. EUT stopped operation and could / could not be reset by operator at of Line. No false alarms or other malfunctions were observed during or after the test. The acceptance criteria were met, and the EUT passed the test. Page: 163 of 176 kv

167 Product Barebone Test Item Voltage dips and interruption Test Mode Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Date of Test 2006/09/26 Test Site No.6 Shielded Room Voltage Dips and Interruption Reduction(%) Angle Test Duration (Periods) Required Performance Criteria Performance Test Result Criteria Complied To 30(161V) 0 25 C A PASS 30(161V) C A PASS 30(161V) C A PASS 30(161V) C A PASS 30(161V) C A PASS 30(161V) C A PASS 30(161V) C A PASS 30(161V) C A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information The nominal voltage of EUT is 230V. EUT stopped operation and could / could not be reset by operator at of Line. No false alarms or other malfunctions were observed during or after the test. The acceptance criteria were met, and the EUT passed the test. kv Page: 164 of 176

168 Product Barebone Test Item Voltage dips and interruption Test Mode Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Date of Test 2006/09/26 Test Site No.6 Shielded Room Voltage Dips and Interruption Reduction(%) Angle Test Duration (Periods) Required Performance Criteria Performance Test Result Criteria Complied To 30(161V) 0 25 C A PASS 30(161V) C A PASS 30(161V) C A PASS 30(161V) C A PASS 30(161V) C A PASS 30(161V) C A PASS 30(161V) C A PASS 30(161V) C A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) B A PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS >95(0V) C C PASS Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information The nominal voltage of EUT is 230V. EUT stopped operation and could / could not be reset by operator at of Line. No false alarms or other malfunctions were observed during or after the test. The acceptance criteria were met, and the EUT passed the test. kv Page: 165 of 176

169 14.7. Test Photograph Test Mode : Mode 1:MS-6437,AMD AM2 Sempron 3400+,D-Sub(2048*1536/60Hz) Description : Voltage Dips Test Setup Test Mode : Mode 2:MS-6434,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(1920*1440/60Hz) Description : Voltage Dips Test Setup Page: 166 of 176

170 Test Mode : Mode 4:MS-6429,Intel Pentium IV(LGA 775)3.4GHz/200MHz,D-Sub(2048*1536/75Hz) Description : Voltage Dips Test Setup Page: 167 of 176

171 15. Attachment EUT Photograph (1) EUT Photo (MS-6437) (2) EUT Photo Page: 168 of 176

172 (3) EUT Photo (4) EUT Photo Page: 169 of 176

173 (5) EUT Photo (6) EUT Photo (MS-6434) Page: 170 of 176

174 (7) EUT Photo (8) EUT Photo Page: 171 of 176

175 (9) EUT Photo (10) EUT Photo Page: 172 of 176

176 (11) EUT Photo (MS-6429) (12) EUT Photo Page: 173 of 176

177 (13) EUT Photo (14) EUT Photo Page: 174 of 176

178 (15) EUT Photo (16) EUT Photo Page: 175 of 176

179 (17) EUT Photo (18) EUT Photo Page: 176 of 176