Test Report. Wireless 11g + Bluetooth Combo MiniPCI Card. Applicant MICRO-STAR INT L CO., LTD No.69,Li-De St,Jung-He City,Taipei Hsien 235,Taiwan

Transcription

1 Test Report Product Name Model No. Wireless 11g + Bluetooth Combo MiniPCI Card MS-6855B, MP54G-BT2 Applicant MICRO-STAR INT L CO., LTD Address No.69,Li-De St,Jung-He City,Taipei Hsien 235,Taiwan Date of Receipt Mar. 04, 2005 Issued Date Mar. 15, 2005 Report No. 053L038EI The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Page: 1 of 35

2 Test Report Certification Issued Date : Mar. 15, 2005 Report No. : 053L038EI Product Name Wireless 11g + Bluetooth Combo MiniPCI Card Applicant MICRO-STAR INT L CO., LTD Address No.69,Li-De St,Jung-He City,Taipei Hsien 235,Taiwan Manufacturer MICRO-STAR INT L CO., LTD Model No. MS-6855B, MP54G-BT2 Rated Voltage AC 230V/50Hz Working Voltage DC 3.3V (Power by PC) Trade Name MSI Applicable Standard ETSI EN :V1.4.1 ( ) Test Result Complied The test results relate only to the samples tested. The test report is under the previsions of Directive 1999/5/EC, Article 3.2. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Documented By : ( Rita Huang ) Tested By : 0914 ILAC MRA ( Tom Hsieh ) Approved By : ( Gene Chang ) Page: 2 of 35

3 TABLE OF CONTENTS Report No.: 053L038EI Description Page 1. GENERAL INFORMATION EUT Description Tested System Details Configuration of tested System EUT Exercise Software Test Facility Effective radiated Power Test Equipment Test Setup Test Condition Limits Test Procedure Uncertainty Test Specification Test Result Peak Power Density Test Equipment Test Setup Test Condition Limits Test Procedure Uncertainty Test Specification Test Result Frequency Range Test Equipment Test Setup Test Condition Limits Test Procedure Uncertainty Test Specification Test Result Spurious Emission Test Equipment Test Setup Test Condition Limits Test Procedure Uncertainty Test Specification Test Result Measurement Uncertainty Values EMC Reduction Method During Compliance Testing Test Result Test Data of Effective Radiated Power Test Data of Peak Power Density Test Data of Frequency Range Test Data of Spurious Emission Attachment 1: EUT Test Photographs Attachment 2: EUT Detailed Photographs Page: 3 of 35

4 1. GENERAL INFORMATION 1.1. EUT Description Product Name Wireless 11g + Bluetooth Combo MiniPCI Card Trade Name MSI Model No. MS-6855B, MP54G-BT2 Frequency Range MHz Channel Number 13 Data Speed DSSS: 1, 2, 5.5, 11MHz OFDM: 6, 9, 12, 18, 24, 36, 48, 54MHz Channel separation 5 MHz Type of Modulation DSSS / OFDM Channel Control Auto Antenna Type Connector Antenna Gain 2.99dBi (Test Antenna is MS-1002) Power Adapter MFR: FSP M/N: FSP090-1ADC21 Input: V ~1.6A, 50-60Hz Output: 19.0V 4.74A MAX (90WMAX) Cable out: Non-Shielded, 1.8m with two ferrite cores bonded. Power Cord: Non-Shielded, 1.8m Antenna List Manufacturer Model Peak Gain 1 High-Tek Group MS dbi 2 FAVORTRON AN dbi 3 Well Green Technology E12B 1.92 dbi 4 Walsin technology FIC 1.56 dbi 5 High-Tek Group CLEVO 285P 0.47 dbi 6 FAVORTRON M300N dbi 7 FAVORTRON 258KA dbi 8 FOXCONN N dbi 9 High-Tek Group CLEVO dbi 10 SmartAnt UniWill U dbi 11 High-Tek Group MS dbi 12 High-Tek Group MS dbi 13 FAVORTRON D900T 1.82 dbi 14 High-Tek Group MS dbi 15 SmartAnt MS dbi Page: 4 of 35

5 Working Frequency of Each Channel: Channel Frequency Channel Frequency Channel Frequency Channel Frequency Channel 01: 2412 MHz Channel 02: 2417 MHz Channel 03: 2422 MHz Channel 04: 2427 MHz Channel 05: 2432 MHz Channel 06: 2437 MHz Channel 07: 2442 MHz Channel 08: 2447 MHz Channel 09: 2452 MHz Channel 10: 2457 MHz Channel 11: 2462 MHz Channel 12: 2467 MHz Channel 13: 2472 MHz Note: 1. The EUT is including two models, The MS-6855B for MSI and the MP54G-BT2 PRO for different marketing requirement. 2. Regards to the frequency band operations; two rate that were included the lowest and highest frequency of channel were selected to perform the test, then show on this report. 3. This device is a composite device in accordance with ETSI regulations. The EMC was measured and made a test report that the report number is 053L038E. 4. QuieTek has verified all construction and function in typical operation. All the test modes were carried out with the EUT in normal operation, which was shown in this test report and defined as: EMI Mode Mode 1: Transmitter 11Mbps Mode 1: Transmitter 54Mbps Mode 2: Receiver 11Mbps Mode 2: Receiver 54Mbps Page: 5 of 35

6 1.2. Tested System Details The types for all equipment, plus descriptions of all cables used in the tested system (including inserted cards) are: Product Manufacturer Model No. Serial No. Power Cord (1) Notebook PC ASUS S NP Non-Shielded, 1.8m (2) Matrix MSI N/A N/A N/A Signal Cable Type N/A Signal Cable Description N/A 1.3. Configuration of tested System EUT (2) Notebook (1) 1.4. EUT Exercise Software (1) Setup the EUT and simulators as shown on 1.3 (2) Turn on the power of all equipment. (3) Notebook PC reads data from disk. (4) Messages will be transmitted and received through EUT. (5) Test is based on the mandatory continuous transmitter. (6) Repeat the above procedure (4) to (5) Page: 6 of 35

7 1.5. Test Facility Ambient conditions in the laboratory: Items Test Item Required Actual Temperature ( C) ETSI EN Humidity (%RH) Site Description: July 03, 2002 Accreditation on NVLAP NVLAP Lab Code: June 11, 2001 Accreditation on DNV Statement No. : LAB11 April 18, 2001 Accreditation on Nemko Certificate No.: ELA 165 May 03, 2001 Accreditation on TUV Rheinland Certificate No.: ILAC MRA Site Name: Site Address: Quietek Corporation No. 5, Ruei-Shu Valley, Ruei-Ping Tsuen, Lin-Kou Shiang, Taipei, Taiwa, R.O.C. TEL : / FAX : service@quietek.com Page: 7 of 35

8 2. Effective radiated Power 2.1. Test Equipment The following test equipments are used during the radiated emission tests: Equipment Manufacturer Model No./Serial No. Last Cal. Remark Spectrum Analyzer Advantest R3162C / May, 2004 Temperature Chamber TDE CHM 150CT Mar., 2005 Note: 1. All equipment upon which need to calibrated are with calibration period of 1 year Test Setup Conduction Power Measurement Spectrum 12dBuV Temperature Chamber Power Supply 2.3. Test Condition Standard Temperature and Humidity, Standard Test Voltage 2.4. Limits The effective radiated power is defined as the total power of the transmitter. The effective radiated power shall be equal to or less than -10 dbw (100 mw) e.i.r.p. This limit shall apply for any combination of power level and intended antenna assembly. Page: 8 of 35

9 2.5. Test Procedure The following method of measurement shall apply to both conducted and radiated measurements. The measurement shall be performed using normal operation of the equipment with modulation, using the test data sequence, applied. Using a suitable means, the output of the transmitter shall be coupled to a diode detector; the output of the diode detector shall be connected to the vertical channel of an oscilloscope; the combination of the diode detector and the oscilloscope shall be capable of faithfully reproducing the envelope peaks and the duty cycle of the transmitter output signal. The measurement shall be repeated at the lowest, the middle, and highest frequency of the stated frequency range. FHSS equipment shall be made to hop continuously to each of these three frequencies separately Uncertainty The measurement uncertainty is defined as ± 1.27dB 2.7. Test Specification According to ETSI EN :V1.4.1 ( ) 2.8. Test Result The emission from the EUT was below the specified limits. The worst-case emissions are shown in section 8. The acceptance criterion was met and the EUT passed the test. Page: 9 of 35

10 3. Peak Power Density 3.1. Test Equipment The following test equipments are used during the radiated emission tests: Equipment Manufacturer Model No./Serial No. Last Cal. Remark Spectrum Analyzer Advantest R3162C / May, 2004 Note: 1. All equipment upon which need to calibrated are with calibration period of 1 year Test Setup EUT RF Cable SMA Connecter Spectrum Analyzer 3.3. Test Condition Standard Temperature and Humidity, Standard Test Voltage 3.4. Limits The maximum spectral power density is defined as the highest level of power in Watts per Hertz generated by the transmitter within the power envelope. For equipment using FHSS modulation, the maximum spectral power density shall be limited to -10 dbw (100 mw) per 100 khz e.i.r.p. For equipment using other types of modulation, the maximum spectral power density shall be limited to-20 dbw(10 mw) per MHz e.i.r.p. Page: 10 of 35

11 3.5. Test Procedure The maximum spectral power density shall be determined using a spectrum analyzer of adequate bandwidth for the type of modulation being used in combination with an RF power meter. Connect an RF power meter to the IF output of the spectrum analyzer and correct its reading using a known reference source, e.g. a signal generator. The above procedure shall be repeated for each of the three frequencies identified by the procedure given in limit (subclause ) Where the spectrum analyzer bandwidth is non-gaussian, a suitable correction factor shall be determined and applied. Where a spectrum analyzer is equipped with a facility to measure power density, this facility may be used instead of the above procedure Uncertainty The measurement uncertainty is defined as ± 1.27 db 3.7. Test Specification According to ETSI EN :V1.4.1 ( ) 3.8. Test Result The emission from the EUT was below the specified limits. The worst-case emissions are shown in section 8. The acceptance criterion was met and the EUT passed the test. Page: 11 of 35

12 4. Frequency Range 4.1. Test Equipment Equipment Manufacturer Model No./Serial No. Last Cal. Remark Spectrum Analyzer Advantest R3162C / May, 2004 Temperature Chamber TDE CHM 150CT Mar., 2005 Note: 1. All equipment upon which need to calibrated are with calibration period of 1 year Test Setup Conduction Power Measurement Spectrum 12dBuV Temperature Chamber 4.3. Test Condition Power Supply Standard Temperature and Humidity, Standard Test Voltage 4.4. Limits The frequency range of the equipment is determined by the lowest and highest frequencies occupied by the power envelope. f H is the highest frequency of the power envelope: it is the frequency furthest above the frequency of maximum power where the output power drops below the level of -80 dbm/hz e.i.r.p. spectral power density (-30 dbm if measured in a100 khz bandwidth). f L is the lowest frequency of the power envelope; it is the frequency furthest below the frequency of maximum power where the output power drops below the level equivalent to -80 dbm/hz e.i.r.p. spectral power density (or -30 dbm if measured in a 100 khz bandwidth). Page: 12 of 35

13 For a given operating frequency, the width of the power envelope is (f H - f L). In equipment that allows adjustment or selection of difference operation frequencies, the power envelope takes up difference positions in the allowed band. The frequency range is determined by the lowest value of f L and the highest value of f H resulting from the adjustment of the equipment to the lowest and highest operating frequencies. For all equipment the frequency range shall lie within the band 2.4GHz to GHz (f L > 2.4GHz and f H < GHz) Test Procedure The measurement procedure shall be as follows: a) Place the spectrum analyzer in video averaging mode with a minimum of 50 sweeps selected and activate the transmitter with modulation applied. The RF emission of the equipment shall be displayed on the spectrum analyzer; b) Select lowest operating frequency of the equipment under test; c) Using the marker of the spectrum analyzer, find lowest frequency below the operating frequency at which spectral power density drops below the level given in limit (subclause 5.2.3); d) Select the highest operating frequency of the equipment under test; e) Find the highest frequency at which the spectral power density drops below the value given in limit (subclause ); f) The difference between the frequencies measured in steps c) and e) is the frequency range Uncertainty The measurement uncertainty is defined as ± 100 khz 4.7. Test Specification According to ETSI EN :V1.4.1 ( ) 4.8. Test Result The emission from the EUT was below the specified limits. The worst-case emissions are shown in section 8. The acceptance criterion was met and the EUT passed the test. Page: 13 of 35

14 5. Spurious Emission 5.1. Test Equipment The following test equipment are used during the radiated emission test: Test Site Equipment Manufacturer Model No./Serial No. Last Cal. Site # 1 Test Receiver R & S ESVS 10 / /003 July, 2004 Spectrum Analyzer Advantest R3162/ May, 2004 Pre-Amplifier Advantest BB525C/ 3307A01812 May, 2004 Bilog Antenna SCHAFFNER CBL6112B / 2697 Nov., 2004 Site # 2 Test Receiver R & S ESCS 30 / / 022 Nov., 2004 Spectrum Analyzer Advantest R3162 / May, 2004 Pre-Amplifier Advantest BB525C/3307A01814 May, 2004 Bilog Antenna SCHAFFNER CBL6112B / 2705 Oct., 2004 Horn Antenna ETS 3115 / July, 2004 Pre-Amplifier QTK QTK-AMP-01/ 0001 July, 2004 Site # 3 Test Receiver R & S ESI 26 / / 004 May, 2004 Spectrum Analyzer Advantest R3162 / May, 2004 Pre-Amplifier QTK QTK-AMP-03 / 0003 May, 2004 Bilog Antenna SCHAFFNER CBL6112B / 2697 May, 2004 Horn Antenna ETS 3115 / July, 2004 Pre-Amplifier QTK QTK-AMP-01 / 0001 July, 2004 Note: 1. All equipments that need to calibrate are with calibration perio d of 1 year. 2. Mark X test instruments are used to measure the final test results Test Setup 3m FRP Dome 1m to 4m Non-Conducted Table Load EUT Antenna Mast Bilog or Horn Antenna Antenna height can be moved from 1m to 4m, Antenna and turntable distance 3m 1.5 m Test Receiver Fully Soldered Ground Plane TO Controller To Receiver Page: 14 of 35

15 5.3. Test Condition Standard Temperature and Humidity, Standard Test Voltage 5.4. Limits Transmitter limits for narrowband spurious emission Frequency Range Limit when operating Limit when in standby 30MHzto 1 GHz -36 dbm -57 dbm Above 1 GHz to GHz -30 dbm -47 dbm 1.8 GHz to 1.9 GHz 5.15 GHz to 5.3 GHz -47 dbm -47 dbm Transmitter limits for wideband spurious emission Frequency Range Limit when operating Limit when in standby 30MHzto 1 GHz -86 dbm/hz -107 dbm/hz Above 1 GHz to GHz -80 dbm/hz -97 dbm/hz 1.8 GHz to 1.9 GHz 5.15 GHz to 5.3 GHz -97 dbm/hz -97 dbm/hz Narrowband spurious emission limit for receivers Frequency Range 30MHzto 1 GHz Above 1 GHz to GHz Limit -57 dbm -47 dbm Wideband spurious emission limit for receivers Frequency Range 30MHzto 1 GHz Above 1 GHz to GHz Limit -107 dbm/hz -97 dbm/hz Page: 15 of 35

16 5.5. Test Procedure The EUT and its simulators are placed on a turn table which is 1.5 meters above ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 3 meters.the antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. Broadband antenna (calibrated bi-log and horn antenna) are used as a receiving antenna. Both horizontal and vertical polarization of the antenna are set on measurement. And a high frequency preamlifier were used increase the sensitivity of the measuring. In order to find the maximum emission, all of the interface cables must be manipulated according to ETSI EN :V1.4.1 ( ) on radiated measurement. The additional notch filter below 1GHz was used to measure the level of harmonics radiated emission during field dtrength of harmonics measurement. The bandwidth setting on the field strength meter (R & S Spectrum Analyzer FSP40 )is 100 khz. The frequency range from 30MHz to 12.75GHz is checked Uncertainty The measurement uncertainty above 1G is defined as ± 3.9 db under 1G is defined as ± 3.8 db 5.7. Test Specification According to ETSI EN :V1.4.1 ( ) 5.8. Test Result The emission from the EUT was below the specified limits. The worst-case emissions are shown in section 8. The acceptance criterion was met and the EUT passed the test. Page: 16 of 35

17 6. Measurement Uncertainty Values The maximum values of the absolute measurement uncertainties of the measurements defined in the present document shall not exceed the values given below: Parameter Uncertainty Radio frequency ± 1 x10 5 Total RF power, conducted ± 1.5 db RF power density, conducted ± 3 db Spurious emissions, conducted ± 3 db All emissions, radiated ± 6 db Temperature ± 1 o C Humidity ± 5 % DC and low frequency voltages ± 3 % Page: 17 of 35

18 7. EMC Reduction Method During Compliance Testing No modification was made during testing. Page: 18 of 35

19 8. Test Result The test results in the emission and the immunity were performed according to the requirements of measurement standard and process. Quietek Corporation is assumed full responsibility for the accuracy and completeness of these measurements. The test data of the emission is listed as below. All the tests were carried out with the EUT in normal operation, which was defined as: EMI Mode Mode 1: Transmitter 11Mbps Mode 1: Transmitter 54Mbps Mode 2: Receiver 11Mbps Mode 2: Receiver 54Mbps Page: 19 of 35

20 8.1. Test Data of Effective Radiated Power Product : Wireless 11g + Bluetooth Combo MiniPCI Card Test Item : Effective Radiated Power Test Mode : Mode 1: Transmitter 11Mbps Antenna Gain: 2.99dBi, Duty Cycle: 1, Cable Loss: 0.5dB Test Conditions Channel Freq. (MHz) Reading Level (dbm) Emission Level (dbm) Limit (dbm) Tnom (25) o C Vnom (230) V Tmax (35) o C Vmax (253) V Tmax (35) o C Vmin (207) V Tmin (0) o C Vmax (253) V Tmin (0) o C Vmin (207) V * Emission Level = Reading Level + Antenna Gain + 10 log (1/Duty Cycle) Remark: Channel 1 Channel 7 Channel 13 Lowest frequency at the appropriate spurious emission level Middle frequency at the appropriate spurious emission level Highest frequency at the appropriate spurious emission level Page: 20 of 35

21 Product : Wireless 11g + Bluetooth Combo MiniPCI Card Test Item : Effective Radiated Power Test Mode : Mode 1: Transmitter 54Mbps Antenna Gain: 2.99dBi, Duty Cycle: 1, Cable Loss: 0.5dB Test Conditions Channel Freq. (MHz) Reading Level (dbm) Emission Level (dbm) Limit (dbm) Tnom (25) o C Vnom (230) V Tmax (35) o C Vmax (253) V Tmax (35) o C Vmin (207) V Tmin (0) o C Vmax (253) V Tmin (0) o C Vmin (207) V * Emission Level = Reading Level + Antenna Gain + 10 log (1/Duty Cycle) Remark: Channel 1 Channel 7 Channel 13 Lowest frequency at the appropriate spurious emission level Middle frequency at the appropriate spurious emission level Highest frequency at the appropriate spurious emission level Page: 21 of 35

22 8.2. Test Data of Peak Power Density Product : Wireless 11g + Bluetooth Combo MiniPCI Card Test Item : Peak Power Density Test Mode : Mode 1: Transmitter 11Mbps Channel Freq. Reading Level Measure Level Limit (MHz) (dbm) (dbm) (dbm/mhz) Antenna Gain: 2.99dBi, Duty Cycle: 1, Cable Loss: 0.45dB * Measure Level = Reading Level + Antenna Gain + 10 log (1/Duty Cycle) Test Result PASS Remark: Channel 1 Channel 7 Channel 13 Lowest frequency at the appropriate spurious emission level Middle frequency at the appropriate spurious emission level Highest frequency at the appropriate spurious emission level Page: 22 of 35

23 Product : Wireless 11g + Bluetooth Combo MiniPCI Card Test Item : Peak Power Density Test Mode : Mode 1: Transmitter 54Mbps Channel Freq. Reading Level Measure Level Limit (MHz) (dbm) (dbm) (dbm/mhz) Antenna Gain: 2.99dBi, Duty Cycle: 1, Cable Loss: 0.45dB * Measure Level = Reading Level + Antenna Gain + 10 log (1/Duty Cycle) Test Result PASS Remark: Channel 1 Channel 7 Channel 13 Lowest frequency at the appropriate spurious emission level Middle frequency at the appropriate spurious emission level Highest frequency at the appropriate spurious emission level Page: 23 of 35

24 8.3. Test Data of Frequency Range Product : Wireless 11g + Bluetooth Combo MiniPCI Card Test Item : Frequency Range Test Mode : Mode 1: Transmitter 11Mbps Test Conditions Tnom (25) o C Vnom (230) V Tmax (35) o C Vmax (253) V Tmax (35) o C Vmin (207) V Tmin (0) o C Vmax (253) V Tmin (0) o C Vmin (207) V Frequency (MHz) F L F H F L F H F L F H F L F H F L F H Test Result F L : MHz F H : MHz Remark: F L F H Lowest frequency at the appropriate spurious emission level Highest frequency at the appropriate spurious emission level Page: 24 of 35

25 Product : Wireless 11g + Bluetooth Combo MiniPCI Card Test Item : Frequency Range Test Mode : Mode 1: Transmitter 54Mbps Test Conditions Tnom (25) o C Vnom (230) V Tmax (35) o C Vmax (253) V Tmax (35) o C Vmin (207) V Tmin (0) o C Vmax (253) V Tmin (0) o C Vmin (207) V Frequency (MHz) F L F H F L F H F L F H F L F H F L F H Test Result F L : MHz F H : MHz Remark: F L F H Lowest frequency at the appropriate spurious emission level Highest frequency at the appropriate spurious emission level Page: 25 of 35

26 8.4. Test Data of Spurious Emission Product : Wireless 11g + Bluetooth Combo MiniPCI Card Test Item : Spurious Emission Test Site : No.3 OATS Test Mode : Mode 1: Transmitter 11Mbps (Channel 1) Frequency Measurement Reading Correction Factor Limit Margin (MHz) (dbm) (dbm) (db) (dbm) (db) Peak Detector (Horizontal) Peak Detector (Vertical) Note: 1. All Reading are peak value. 2., means this data is the worst emission level. 3. Emission Level = Reading Level + Correction Factor Page: 26 of 35

27 Product : Wireless 11g + Bluetooth Combo MiniPCI Card Test Item : Spurious Emission Test Site : No.3 OATS Test Mode : Mode 1: Transmitter 11Mbps (Channel 13) Frequency Measurement Reading Correction Factor Limit Margin (MHz) (dbm) (dbm) (db) (dbm) (db) Peak Detector (Horizontal) Peak Detector (Vertical) Note: 1. All Reading are peak value. 2., means this data is the worst emission level. 3. Emission Level = Reading Level + Correction Factor Page: 27 of 35

28 Product : Wireless 11g + Bluetooth Combo MiniPCI Card Test Item : Spurious Emission Test Site : No.3 OATS Test Mode : Mode 1: Transmitter 54Mbps (Channel 1) Frequency Measurement Reading Correction Factor Limit Margin (MHz) (dbm) (dbm) (db) (dbm) (db) Peak Detector (Horizontal) Peak Detector (Vertical) Note: 1. All Reading are peak value. 2., means this data is the worst emission level. 3. Emission Level = Reading Level + Correction Factor Page: 28 of 35

29 Product : Wireless 11g + Bluetooth Combo MiniPCI Card Test Item : Spurious Emission Test Site : No.3 OATS Test Mode : Mode 1: Transmitter 54Mbps (Channel 13) Frequency Measurement Reading Correction Factor Limit Margin (MHz) (dbm) (dbm) (db) (dbm) (db) Peak Detector (Horizontal) Peak Detector (Vertical) Note: 1. All Reading are peak value. 2., means this data is the worst emission level. 3. Emission Level = Reading Level + Correction Factor Page: 29 of 35

30 Product : Wireless 11g + Bluetooth Combo MiniPCI Card Test Item : Spurious Emission Test Site : No.3 OATS Test Mode : Mode 2: Receiver 11Mbps (Channel 1) Frequency Measurement Reading Correction Factor Limit Margin (MHz) (dbm) (dbm) (db) (dbm) (db) Peak Detector (Horizontal) Peak Detector (Vertical) Note: 1. All Reading are peak value. 2., means this data is the worst emission level. 3. Emission Level = Reading Level + Correction Factor Page: 30 of 35

31 Product : Wireless 11g + Bluetooth Combo MiniPCI Card Test Item : Spurious Emission Test Site : No.3 OATS Test Mode : Mode 2: Receiver 11Mbps (Channel 13) Frequency Measurement Reading Correction Factor Limit Margin (MHz) (dbm) (dbm) (db) (dbm) (db) Peak Detector (Horizontal) Peak Detector (Vertical) Note: 1. All Reading are peak value. 2., means this data is the worst emission level. 3. Emission Level = Reading Level + Correction Factor Page: 31 of 35

32 Product : Wireless 11g + Bluetooth Combo MiniPCI Card Test Item : Spurious Emission Test Site : No.3 OATS Test Mode : Mode 2: Receiver 54Mbps (Channel 1) Frequency Measurement Reading Correction Factor Limit Margin (MHz) (dbm) (dbm) (db) (dbm) (db) Peak Detector (Horizontal) Peak Detector (Vertical) Note: 1. All Reading are peak value. 2., means this data is the worst emission level. 3. Emission Level = Reading Level + Correction Factor Page: 32 of 35

33 Report No. 053L038EI Product : Wireless 11g + Bluetooth Combo MiniPCI Card Test Item : Spurious Emission Test Site : No.3 OATS Test Mode : Mode 2: Receiver 54Mbps (Channel 13) Frequency Measurement Reading Correction Factor Limit Margin (MHz) (dbm) (dbm) (db) (dbm) (db) Peak Detector (Horizontal) Peak Detector (Vertical) Note: 1. All Reading are peak value. 2., means this data is the worst emission level. 3. Emission Level = Reading Level + Correction Factor Page:33 of 35

34 Report No. 053L038EI Attachment 1: EUT Test Photographs Page:34 of 35

35 Attachment 1: EUT Test Setup Photographs Front View of Radiated Test Back View of Radiated Test Page : 1 of 2

36 Front View of Radiated Test (Horn) Back View of Radiated Test (Horn) Page : 2 of 2

37 Report No. 053L038EI Attachment 2: EUT Detailed Photographs Page:35 of 35

38 Attachment 2 : EUT Detailed Photographs (1) EUT Photo (2) EUT Photo Page : 1 of 10

39 (3) EUT Photo (4) EUT Photo Page : 2 of 10

40 (5) EUT Photo (6) EUT Photo Page : 3 of 10

41 (7) EUT Photo (8) EUT Photo Page : 4 of 10

42 (9) EUT Photo (10) EUT Photo Page : 5 of 10

43 (11) EUT Photo (12) EUT Photo Page : 6 of 10

44 (13) EUT Photo (14) EUT Photo Page : 7 of 10

45 (15) EUT Photo (16) EUT Photo Page : 8 of 10

46 (17) EUT Photo (18) EUT Photo Page : 9 of 10

47 (19) EUT Photo (20) EUT Photo Page : 10 of 10